Sony PCG-V505BCK, PCG-V505BCP, PCG-V505BX, PCG-V505BXP User Guide

Welcome

Congratulations on your purchase of this Sony VAIO® computer, and welcome to the online VAIO® Computer User Guide. This user guide provides detailed information on all aspects of using your new VAIO computer, from keyboard functions to preinstalled software programs. In the left navigation window, click the topics you want to learn more about, and that information will be displayed in this main window.

View the Electronic Flyer, which provides updates and supplemental information about your computer.

View the VAIO® Computer Specifications, which lists your computer's hardware specifications and preinstalled software information, such as descriptions and contact information.

Page 1

Powering Your Computer

Your VAIO® computer comes with a battery and an AC adapter. This chapter explains how to install and use these supplied accessories to power your computer. It also describes ways you can efficiently utilize the battery as a power source.

Using AC Power



Using the Battery



Conserving Battery Power



Page 2

Using AC Power

The supplied battery is not charged when you receive your computer. To use your computer immediately, use the supplied AC adapter as the power source. While the computer uses AC power, it automatically charges the battery if it is inserted. See Using the Battery for more information on installing and using your battery.

Connecting the AC adapter



Turning on the computer



Page 3

Connecting the AC adapter

To connect the AC adapter

Plug the AC adapter cable into the DC IN port.

Connecting the AC Adapter to the Computer

Plug the power cord into the AC adapter and an AC outlet.

Use only the supplied AC adapter with your computer.

Page 4

Turning on the computer

To turn on the computer

Lift the lid of the computer by sliding the front switch to the right and lifting the lid. You may need to hold the bottom of the computer firmly to lift the lid.

Opening the Computer

Slide the power switch to the right until the power indicator turns on.

Turning on the Computer

If you slide and hold the power switch, the computer turns off.

If the computer screen is too dark or too bright, follow these steps to adjust the brightness:

To increase brightness, press the Fn and F5 keys, and then press the Up Arrow or the Right Arrow



key.

To decrease brightness, press the Fn and F5 keys, and then press the Down Arrow or the Left



Arrow key.

Page 5

Using the Battery

Your computer, depending on the model you purchased, may come equipped with one battery bay and one multipurpose bay that supports a second battery. If your computer comes with two bays, you can purchase a second rechargeable battery to extend your computing time. For information on how to extend the life of the battery, see Conserving Battery

Power for more information.

Inserting a battery



Removing a battery



Locating battery information



Charging a battery



Notes on batteries



Frequently asked questions



When operating your computer on battery power, your computer's CPU speed is reduced.

The battery that comes with your computer is not fully charged at the time of purchase.

The brightness of your computer screen automatically dims when you switch from AC power to battery power. To

increase the brightness, press the Fn and F5 keys, and then press the Up Arrow or Right Arrow key.

Page 6

Inserting a battery

To insert a battery

Turn the computer over, and slide the LOCK/UNLOCK switch on the bottom of the computer to the UNLOCK position.

Align the grooves on the battery with the tabs on the back of the computer.

Inserting a Battery

Slide the battery into the computer until it clicks into place.

Slide the LOCK/UNLOCK switch into the LOCK position.

If a port replicator is attached to your computer, do not insert or remove the battery. Lifting and turning the computer with the port replicator attached could cause a temporary loss of power.

Some programs and peripheral devices prevent the system from automatically entering Hibernate mode. If you are using battery power, save your data frequently to avoid data loss and manually activate a power saving mode. See Using power

saving modes for more information.

Page 7

Removing a battery

If you are not using the computer for an extended period of time, remove the battery from the computer to avoid damaging the battery. You can remove the battery when the computer is on or off.

If the computer is on, connect the AC adapter and exit a power saving mode before you remove the battery.

To remove a battery

Turn the computer over, and slide the LOCK/UNLOCK switch on the bottom of the computer to the UNLOCK position.

Push and hold the RELEASE switch.

While holding the RELEASE switch, slide the battery away from the computer.

Remov ing a Battery

Page 8

Locating battery information

You can display information for the battery installed in your computer.

To view battery information

Click Start on the Windows® taskbar, and click Control Panel.

Click Performance and Maintenance, and click Power Options. The Power Options Properties window appears.

Select the Power Meter tab. The total remaining battery charge is listed as a percentage. If your computer comes with more than one battery, you can view information on both batteries or just the primary battery.

You may also use the power icon on the Windows® taskbar to quickly view battery information. See To display the

power icon on the taskbar for instructions on how to set up this shortcut.

To display the power icon on the taskbar

Click Start on the Windows® taskbar, and click Control Panel.

Click Performance and Maintenance, and click Power Options. The Power Options Properties window appears.

Select the Advanced tab, and then select Always show icon on the taskbar in the Options box. The power icon appears on the taskbar. See the power icon descriptions below for more information.

You can rollover the power icon to view the remaining battery charge, and you can double-click the power icon to open the Power Meter window, which also displays the remaining battery charge.

Power icon Power status

Computer is using AC power.

Computer is using AC power and charging the battery.

Battery is charging.

Battery is fully charged.

Battery is discharging.

No battery is inserted in the computer.

Page 9

Charging a battery

You will need to charge the battery if battery power drops below 10 percent or you have not used the battery for a long time. The lithium-ion battery supplied with your computer may be recharged at any time, whether you wait until the battery is completely or partially discharged. Charging a partially discharged battery does not affect battery life. If you charge the battery and find that battery power is still low, the battery may be reaching the end of its life, and you may need to replace it.

The battery supplied with your computer is not charged at the time of purchase.

To charge a battery

You can charge the battery when the computer is on or off. However, the battery will charge faster when the computer is off. Charging the battery takes several hours. See your VAIO® Computer Specifications on the Welcome page for the approximate time needed to charge your battery.

Charge the battery at temperatures between 50°F and 80°F (10°C to 30°C). Lower temperatures require more time to charge.

Insert the battery into the battery bay.

Connect the AC adapter to the computer. The computer automatically charges the battery as long as the computer is using AC power.

The battery indicator blinks while the battery charges. The battery indicator stops blinking when the battery is fully charged.

When using two batteries, the battery you insert first charges first. The second battery you insert begins charging when the first battery is 85 percent charged.

Battery Indicators

Battery indicator status Description

On The computer is using battery power.

Single blink The battery is running out of power.

Double blink The battery is charging.

Off The computer is using AC power.

Page 10

Notes on batteries

Never leave the battery in temperatures above 140°F (60°C), such as under direct sunlight or in a car parked in the



sun.

While the battery is in use or being discharged, the battery heats up. This is normal and is not cause for concern.



Keep the battery away from all sources of heat.



Keep the battery dry.



Do not open or disassemble the battery.



Do not expose the battery to any mechanical shock.



Battery life is shorter in a cold environment because of decreased battery efficiency at low temperatures.



Page 11

Frequently asked questions

How do I know when the battery is charged?

To determine the remaining battery charge, see Locating battery information.

When is the computer using AC power?

When the computer is directly connected to the AC adapter, it uses AC power, even if a battery is installed.

When should I recharge the battery?

When the battery level falls below 10 percent.



When both the battery and power indicators blink.



When you have not used the battery for a long time.



When should I replace the battery?

If the battery power is still low after charging it, the battery may be reaching the end of its life and should be replaced.

Should I be concerned that the installed battery is warm?

No, it is normal for the battery to be warm when it is powering the computer.

Page 12

Conserving Battery Power

You may use the power saving modes and PowerPanel utility or power schemes to conserve battery power. Conserving battery power may significantly extend your computing time, depending on how you use your computer.

Using power saving modes



Using PowerPanel utility



Frequently asked questions



Page 13

Using power saving modes

In addition to the normal operating mode, which allows you to turn off specific devices to save power, your computer has two distinct power saving modes: Standby and Hibernate. Use the Standby and Hibernate power saving modes to override a power profile setting and initiate immediate action.

Standby — Saves the state of the system and peripheral devices in memory (RAM). Power consumption is reduced



to a minimum. The system remains on, and the computer screen (LCD) is off.

Hibernate — Saves the state of the system and peripheral devices to the hard disk. Power consumption is reduced



to the lowest possible setting without being completely off. Hibernate mode consumes the lowest level of power. Your computer enters Hibernate mode when the remaining battery charge drops below 5 percent, regardless of the setting you select.

Since some software programs and peripheral devices prevent the system from entering Hibernate mode, save your data frequently to avoid data loss.

To activate Standby mode

Press the Fn and Esc keys. The power indicator blinks in this mode.

Press any key to return to normal mode.

To activate Hibernate mode

Press the Fn and F12 keys, or press the power button and release it immediately. Do not move the computer until the power indicator turns off.

Slide the power switch to the right to return to normal mode.

If the computer does not activate Hibernate mode, see Frequently asked questions for more information.

Page 14

Using PowerPanel utility

The PowerPanel utility enables you to select and customize a predefined power management profile to conserve battery life. The following table describes all the predefined power management profiles in PowerPanel. Your computer is set to Maximum Battery Life by default. You can customize the settings for all the following profiles, except the Disable Power Management profile.

Profile

Icon Description

Maximum Performance

Provides the best system performance but conserves minimal power.

Maximum Battery Life Provides power saving features to give you maximum battery life and good performance. It slows the computer and puts it into Standby mode after a specified time.

Ultimate Battery Life Extends the Maximum Battery Life by stopping power to the optical drive.

Power Management Off Disables all power management settings, such as Standby and Hibernate modes. You cannot change the settings of this profile.

AC Power Indicates when AC power is in use. Similar to the Power Management Off setting. Power Management automatically loads the AC profile unless you disable this feature.

Games Disables the display and the Hard Disk Standby timer.

Presentation Keeps the display on at all times while conserving power. This option is ideal for slide show presentations. You can establish settings for LCD (Video) Standby, Hard Disk Standby, and Standby mode to optimize power management for your system.

Camera Optimizes performance and power requirements for camera usage.

DVD

Optimizes performance and power requirements for DVD usage.

Word Processing

Optimizes power management with longer time-outs on the hard disk and display screen. You can also establish settings for LCD (Video) Standby, Hard Disk Standby, and Standby mode to optimize power management for your system.

Spreadsheet

Optimizes performance and power requirements for spreadsheet programs.

Communications

Extends battery life by initiating a quick display time-out. The Internal modem remains powered on. You can also establish settings for LCD (Video) Standby, Hard Disk Standby, and Standby mode to optimize power management for your system.

Automatic Profile Selection Automatically selects a profile suitable for active software programs.

Page 15

Do not choose the Automatic Profile Selection when connected to AC power.

To select a profile

Right-click the CPU icon on the Taskbar Notification area.

Select Profiles, and click the profile name on the shortcut menu. The profile settings are implemented instantly. See Using PowerPanel utility for descriptions of available profiles.

When you use the battery to power your computer, your system automatically selects the Maximum Battery Life power management profile by default. If you select a different power management profile while using battery power, that profile is selected automatically the next time you use the battery to power your computer.

See PowerPanel Help for information on customizing the power management profiles.

To customize your profile settings

You can customize your profile settings to sustain enough power for a particular computing function.

Right-click the CPU icon on the Taskbar Notification area.

Select Edit/Create Profiles from the shortcut menu.

In the left panel, select the profile you want to change.

Right-click the setting under System, LCD(Video), Hard Disk, or Other Devices that you want to change. See the following table for a description of each power management setting.

Make your changes from the drop-down menu.

Click File, and click Save.

Power management settings Description

CPU Control1 Controls the processor speed. You can select either Performance, Adaptive, Battery Life, or More Battery Life. These selections are listed in order from the greatest to least amount of power consumed.

System

Standby Timer Controls the time it takes the system to activate the Standby mode when it is idle. The longer you allow the computer to sit idle while it is not in a power saving mode the more power the computer consumes.

Hibernate Timer Controls the time it takes the system to activate the Hibernate mode when it is idle. The longer you allow the computer to sit idle while it is not in a power saving mode the more power the computer consumes. Hibernate mode conserves more power than Standby mode.

Thermal Control Strategy1 (CPU fan control) (On selected models) Controls the speed of the processor fan. You can set the fan speed to Quiet, which conserves the most power, or Performance.

Lid Close Action Controls the state of your system when you close the computer's lid. You can select either Standby or Hibernate mode, or you can select LCD Off. Hibernate or LCD Off conserves the most power.

Hibernate on Low Battery Controls the state of your system when the battery power is low. You can turn this setting On or Off. Selecting On conserves the most power when the battery is low.

LCD Brightness Controls the brightness of the computer screen (LCD). You can select a brightness level of one to nine, with

Page 16

one being the darkest setting. The darker you set the computer screen the more power you conserve.

LCD Standby Timer Controls the time it takes the system to turn off power to the computer screen (LCD) when the system is idle. The system itself still functions on full power.

HDD Standby Timer Controls the time it takes the system to turn off power to the hard disk drive when the system is idle. This setting only turns off power to the hard disk drive.

i.LINK Port Controls power to the i.LINK® port. Disabling power to the i.LINK port conserves power.

Memory Stick Port Power-saving Controls power to the Memory Stick media slot. Disabling power to the Memory Stick slot conserves power.

Optical Drive Power-Saving Controls power to the optical drive. Disabling power to the optical drive conserves power.

Slows the process or s peed.

Page 17

Frequently asked questions

Can my computer enter Hibernate mode while using battery power?

Your computer can enter Hibernate mode while using battery power, but some software programs and peripheral devices prevent the system from entering Hibernate mode at all. If you are using a program that prevents the system from entering Hibernate mode, save your data frequently. See To activate Hibernate mode for information on how you can manually activate Hibernate mode.

Why doesn't my computer enter Hibernate mode?

You may first need to enable Hibernate mode. Follow these steps:

Click Start on the Windows® taskbar, and click Control Panel.

Click Performance and Maintenance, and click Power Options. The Power Options Properties window appears.

Select the Hibernate tab.

Click to check the box next to Enable hibernation.

Page 18

Internet and Network Connections

Internet Connections



Network Connections



Connecting Another VAIO Computer



Page 19

Internet Connections

This section describes the basic steps for setting up your dial-up or Ethernet connection to the Internet. The New Connection Wizard guides you through the process of connecting to the Internet and choosing an Internet service provider (ISP) or setting up an existing account. When you connect to the Internet, you can register your VAIO® computer, use online services, and gain access to Sony Computing Support.

Setting up a dial-up Internet connection



Setting up an Ethernet Internet connection



Customizing your Internet connection



Frequently asked questions



Page 20

Setting up a dial-up Internet connection

Before you can connect to the Internet, you need to connect your computer to a telephone line via a telephone cable (not supplied). Once you set up your telephone cable, you're ready to connect to the Internet.

To connect a telephone cable

Locate the Modem jack on your computer. For location information, see Locating Ports and Controls in the Setting Up chapter of your printed VAIO® Computer Quick Start.

Plug one end of the telephone cable into the Modem jack. Make sure it clicks into place.

Plug the other end into the wall jack.

Connecting a Telephone Cable

Your computer does not work with party lines, cannot be connected to a coin-operated telephone, and may not work with multiple telephone lines or a private branch exchange (PBX). Some of these connections may result in excess electrical current and could cause a malfunction in the internal modem.

If you connect a telephone cable coming through a splitter, the modem or connected device may not work properly.

To set up a dial-up connection to the Internet

Connect your computer to a telephone line. See To connect a telephone cable for more information.

Click Start, point to All Programs, Accessories, Communications, and click New Connection Wizard. The New Connection Wizard appears.

New Connection Wizard

Page 21

Click Next. If the Location Information dialog box appears, follow the on-screen instructions.

If it is not already selected, click to select Connect to the Internet, and click Next.

Follow the on-screen instructions.

Page 22

Setting up an Ethernet Internet connection

Your computer accommodates both 10BASE-T and 100BASE-TX Ethernet connections, with data transfer speeds of between 10 and 100 Mbps.

To connect an Ethernet cable

Locate the Ethernet port on your computer. For location information, see "Locating Controls and Ports" in the Setting Up chapter of your printed VAIO® Computer Quick Start.

Connecting an Ethernet Cable

Plug one end of the Ethernet cable into your computer's Ethernet port and the other into the network connection.

To set up an Ethernet connection to the Internet

Connect your computer to a network connection.

Click Start, point to All Programs, Accessories, Communications, and click New Connection Wizard. The New Connection Wizard appears.

New Connection Wizard

Page 23

Click Next. If the Location Information dialog box appears, follow the on-screen instructions.

If it is not already selected, click to select Connect to the Internet, and click Next.

Follow the on-screen instructions.

Page 24

Customizing your Internet connection

The Internet Properties dialog box enables you to change the way you view the Internet. You can change your home page, fonts, language, and colors. You can also regulate content and set browsing preferences.

To open the Internet Properties dialog box

Click Start on the Windows® taskbar, and then Control Panel.

Click Network and Internet Connections, and then Internet Options. The Internet Properties dialog box appears.

Click the tabs to view options.

Make changes, and click Apply to activate your changes.

Click OK.

Page 25

Frequently asked questions

Why doesn't my modem work?

Make sure the telephone cable is securely plugged into the Modem jack on the computer and the wall jack. See To



connect a telephone cable for more information.

Make sure the telephone cable is working. Plug the cable into an ordinary telephone and listen for a dial tone.



Make sure the telephone number the program is dialing is correct.



Make sure the software you are using is compatible with the computer's modem. (All preinstalled Sony programs are



compatible.)

Why is my modem connection slow?

Your computer is equipped with a V.90 compatible modem. Many factors may influence modem connection speed, including telephone line noise or compatibility with telephone equipment, such as fax machines or other modems. If you think your modem is not connecting properly to other PC-based modems, fax machines, or your Internet Service Provider (ISP), follow these steps:

Ask your telephone company to verify your telephone line is free of any line noise.



If your problem is fax-related, make sure there are no problems with the fax machine you are calling and that it is



compatible with fax modems.

If you are having a problem connecting with your ISP, make sure the ISP is not experiencing technical problems.



If you have a second telephone line, try connecting the modem to that line.



Page 26

Network Connections

With a Sony computer, you can easily set up or connect to a variety of networks. The New Connection Wizard and Network Setup Wizard make it easy to gain access to remote and local area networks (LANs) using wireless, Ethernet, or dial-up connections.

For more information about networking, click Start, Help and Support, and then Networking and the Web.

Using Ethernet and dial-up connections



Using wireless network connections (selected models only)



Checking your network connection status



Frequently asked questions



Types of Networks*

* T he c omputers repres ented in this graphic may not be identic al to the model you purc has ed.

Page 27

Using Ethernet and dial-up connections

For setting up local area networks (LANs), Ethernet is a widely installed technology. Your computer accommodates both 10BASE-T and 100BASE-TX Ethernet connections, with data transfer speeds of between 10 and 100 Mbps.

To connect to a local area network using a telephone or Ethernet cable

Connect an Ethernet or telephone cable to your computer. See To connect an Ethernet cable and Setting up a

dial-up Internet connection for more information.

Connecting an Ethernet Cable

Click Start, point to All Programs, Accessories, Communications, and click Network Setup Wizard. The Network Setup Wizard appears.

Network Setup Wizard

Click Next. If you are prompted to the Local Information dialog box, follow the on-screen instructions.

Only connect 10BASE-T and 100BASE-TX cables to the Ethernet port . Do not connect any other type

of network cable or any telephone cable. Connecting cables other than those listed above may result in an electric current overload and could cause a malfunction, excessive heat, or fire in the port. To connect the unit to the network,

Page 28

see Using Ethernet and dial-up connections or contact your network administrator.

You can connect to your company network from a remote location and use data, programs, and network resources. See Microsoft® Windows® Help by clicking Help and Support from the Start menu, and then clicking Networking and the Web in the left panel.

To connect to a remote network using a telephone or Ethernet cable

Connect an Ethernet or telephone cable to your computer. See To connect an Ethernet cable and Setting up a

dial-up Internet connection for more information.

From the Start menu, point to All Programs, Accessories, Communications, and click New Connection Wizard.

Click Next. If you are prompted to the Local Information dialog box, follow the on-screen instructions.

Click Connect to the network at my workplace, and then click Next.

Follow the on-screen instructions.

Ask your network administrator for the detailed settings and devices needed to connect to an existing network.

Page 29

Using wireless network connections (selected models only)

A wireless local area network (LAN) is a network in which you can connect to a LAN through a wireless (radio) connection. You can opt to purchase a Sony Wireless LAN Access Point to set up a LAN.

The wireless LAN access point is designed for building a wireless LAN environment. Because a wireless LAN configuration requires no wiring, you can operate multiple computers more freely than ever before.

Your computer is equipped with a built-in mini PCI card that allows for wireless connections. For information about your computer's wireless capabilities, see the Welcome page to view your VAIO® Computer Specifications.

For more information on Sony Wireless LAN, go to http://www.sonystyle.com/vaio.

There are two types of wireless connections:

An infrastructure network is one that extends an existing wired local network to wireless devices by providing an



access point. The access point bridges the wireless and wired LAN and acts as a central controller for the wireless LAN. The access point coordinates transmission and reception from multiple wireless devices within a specific range.

A computer-to-computer (ad-hoc) network is one in which a local network is created only by the wireless devices



themselves, with no other central controller or access point. Each device communicates directly with other devices in the network. You can set up an ad-hoc network easily at home.

To connect to a wireless network

Make sure an access point is set up. See the instructions that accompanied the access point for more information.

Move the Wireless LAN switch to ON.

Turning on the Wireless Network Switch

Click the Wireless Network Connection icon on the taskbar. The Wireless Network Connection dialog box appears.

Wireless Network Connection

Page 30

From the Available wireless networks list, select the name of the network (access point) in which you want to connect. If you do not see the network name, see If the network does not appear in the Available wireless

networks list box.

If required, type the network key in the Network key box. (If necessary, ask the administrator for the key. The key should be between 5 and 13 ASCII characters or 10 to 26 hexadecimal characters.)

Retype the network key in the Confirm network key box.

Click Connect.

If the network does not appear in the Available wireless networks list box

Click Advanced on the Wireless Network Connection dialog box. The Wireless Network Connection Properties dialog box appears.

Wireless Network Connection Properties

Click Add in the Preferred networks box. The Wireless network properties dialog box appears.

Wireless Network Properties

Page 31

Type the name of the network (access point) you want to connect to in the Network name (SSID) box. (The name should be no more than 32 ASCII characters.)

The following steps are for networks that require a network key. If you do not know the network key or are not sure a network key is required, see the network administrator or the guide that accompanied your access point for more information.

Make sure the Data encryption (WEP enabled) check box is selected.

Click to cancel the The key is provided for me automatically check box.

Type the network key in the Network key box. (The key should be between 5 and 13 ASCII characters or 10 to 26 hexadecimal characters.)

Retype the network key in the Confirm network key box.

Click OK. The network name appears in the Preferred networks list box.

To set up a computer-to-computer (ad-hoc) network

Move the Wireless LAN switch to ON.

Turning on the Wireless Network Switch

Click the Wireless Network Connection icon on the taskbar. The Wireless Network Connection dialog box appears.

Wireless Network Connection

Page 32

Click Advanced. The Wireless Network Connection Properties dialog box appears.

Wireless Network Connection Properties

Click Add. The Wireless network properties dialog box appears.

Wireless Network Properties

Page 33

Type the name of the network you want to connect to in the Network name (SSID) box. (The name should be no more than 32 ASCII characters.)

Make sure the Data encryption (WEP enabled) check box is selected.

Click to cancel the The key is provided for me automatically check box.

Type a network key in the Network key box. (The key should be between 5 and 13 ASCII characters or 10 to 26 hexadecimal characters.)

Retype the network key in the Confirm network key box.

10.

Click to select This is a computer-to-computer (ad hoc) network; wireless access points are not used.

11.

Click OK. The network name appears in the Preferred networks list box.

12.

Click Advanced. The Advanced dialog box appears.

Advanced

13.

Click to select Computer-to-computer {ad hoc} networks only, and then click Close.

To disconnect from a wireless network

For computers with built-in wireless LAN functionality, move the Wireless LAN switch to OFF.



Turning off the wireless LAN functionality while accessing remote documents, files, or resources may result in data loss.

To disconnect from a computer-to-computer (ad-hoc) network

Page 34

Click the Wireless Network Connection icon on the taskbar. The Wireless Network Connection Status dialog box appears.

Click Properties. The Wireless Network Connection Properties dialog box appears.

On the Wireless Network tab, click Advanced. The Advanced dialog box appears.

Click to select Any available network (access point preferred), and click Close.

Page 35

Checking your network connection status

Whether you have a wireless, Ethernet, or dial-up connection, you can check the status of that connection.

To check your network connection status

Click Start on the taskbar, and click Control Panel, Network and Internet Connections, and Network Connections. The Network Connections window appears.

Under LAN or High-Speed Internet, click the enabled network connection to open the connection status window.

Wireless Network Connection Status

Page 36

Frequently asked questions

Why can't my computer connect to a wireless LAN access point?

Connection availability is affected by distance and obstructions. You may need to move your computer away from



obstructions or closer to any access point you may be using.

Make sure the Wireless LAN switch on the computer on.



Make sure power to the access point is on.



Make sure the access point is displayed in the Available networks window. For more information, see To connect to



a wireless network.

Make sure the encryption key is correct.



Why can't I access the Internet?



Check the access point settings. Refer to the instructions supplied with the access point.



Make sure your computer and the access point are connected to one another.



Move your computer away from obstructions or closer to any access point you may be using.



Make sure your computer is properly configured for Internet access.

Why is the data transfer speed slow?

The wireless LAN data transfer speed is affected by distance and obstructions between devices and access points.



Other factors include device configurations, radio conditions, and software compatibility. To maximize the data transfer speed, move your computer away from obstructions or closer to any access point you may be using.

If you are using a wireless LAN access point, the device may be temporarily overloaded depending on how many



other devices are communicated via the access point.

If your access point interferes with other access points, change the access point channel. See your access point



instructions for more information.

Why is the communication speed interrupted or slowed down when MPEG2 data is transferred?

The typical effective data transfer speed via an access point is 4-5 Mbps when adhering to the IEEE 802.11b standard. High-rate stream transfers with MPEG2 data may lower this rate.

How do I avoid data transfer interruptions?

When your computer is connected to an access point, data transfer interruptions may occur when using large files



or if the computer is in close proximity to microwaves and cordless telephones.

Move the computer closer to the access point.



Make sure the access point connection is intact. For more information, see Checking your network connection



status.

Change the access point channel. See your access point instructions for more information.



Can I connect to a IEEE 802.11a device?

Computers with built-in wireless LAN support the IEEE 802.11b standard only. Devices connecting to a wireless LAN using the IEEE 802.11a standard cannot connect to devices using the IEEE 802.11b standard.

What are channels?

Wireless LAN communication occurs on divided frequency bands known as channels. Third-party wireless LAN access point channels may be preset to different channels from Sony devices.

If you are using a wireless LAN access point, refer to connectivity information contained in your access point instructions.

Page 37

Connecting Another VAIO Computer

The preinstalled Microsoft® Windows® XP operating system enables you to connect a compatible i.LINK®1 cable (not supplied) between your VAIO® computer and another compatible computer.

Connecting VAIO computers



Disconnecting VAIO computers



Frequently asked questions



i.LINK is a trademark of Sony us ed to des ignate that a produc t c ontains an I E E E 1 3 9 4 c onnection. T he i.LIN K c onnec tion may vary, depending on the software programs, operating system, and c ompatible i.LI N K devic es. A ll products with an i.LI N K c onnec tor may not c ommunic ate with eac h other. Refer to the documentation that came with your compatible i.LIN K devic e for information on operating c onditions and proper c onnec tion. Before c onnecting compatible i.LI N K P C peripherals to your system, s uc h as a C D-RW or hard dis k drive, c onfirm their operating s ystem c ompatibility and required operating conditions.

Page 38

Connecting VAIO computers

When you connect two VAIO computers, you can use one computer to edit, copy, or delete files on the other computer. You can also print from a printer attached to either computer.

To connect VAIO computers

Plug one end of the i.LINK cable into the i.LINK port on each computer.

Click Start on the Windows® taskbar, and click Control Panel.

Click Network and Internet Connections, and click Set up or change your home or small office network. The Network Setup Wizard appears.

Network Setup Wizard

Follow the on-screen Network Setup Wizard instructions.

When you are prompted, type in a unique computer name for each computer. You will use this unique name to differentiate the two computers once they are networked together.

The Workgroup name should remain the same for the two networked computers.

When you finish the Network Setup Wizard on-screen instructions, click Start on the Windows® taskbar and click My Computer.

Click My Network Places in the Other Places menu. The My Network Places window appears.

Click View workgroup computers in the Network Tasks menu. Computers networked under the same workgroup name are displayed in this window.

Connecting Another Computer*

* T his graphic is for illus tration purpos es only. T he c omputers in this graphic may not res emble the model you purc has ed.

Page 39

Disconnecting VAIO computers

You can disconnect two VAIO® computers when the computers are on or off.

To disconnect VAIO computers when the computers are on

Close all open files that are shared with the connected computers.

Unplug the i.LINK® cable from the i.LINK port on each computer.

To disconnect VAIO computer when the computers are off

Unplug the i.LINK cable from the i.LINK port on each computer.



Page 40

Frequently asked questions

Why can't I establish a connection between two VAIO computers?

Your computer may not recognize an i.LINK1 connection if the i.LINK cable is not plugged securely into the i.LINK



ports. Disconnect the i.LINK cable and securely reconnect it to both computers. If neither computer responds after a few moments, restart both computers.

If the computers do not recognize the i.LINK connection after resuming from a power saving mode (Standby or



Hibernate), restart both computers. For more information, see Connecting VAIO computers.

i.LINK is a trademark of Sony us ed only to des ignate that a produc t c ontains an I E E E 1 3 9 4 c onnection. T he i.LIN K c onnec tion may vary, depending on the software applications, operating s ys tem, and c ompatible i.LI NK devices. A ll products with an i.LI N K c onnec tion may not c ommunic ate with eac h other. Refer to the documentation that came with your compatible i.LIN K devic e for information on operating c onditions and proper c onnec tion. Before c onnecting compatible i.LI N K P C peripherals to your system, s uc h as C D-RW or hard dis k drive, c onfirm their operating s ys tem c ompatibility and required operating conditions.

Page 41

CDs and DVDs

Inserting and Ejecting CDs or DVDs



Copying and Playing CDs



Playing DVDs



Page 42

Inserting and Ejecting CDs or DVDs

Avoid using adhesive labels to identify your CDs or DVDs. Adhesive labels may damage the optical drive if they come off while the disc is in the drive.

To insert a disc

Turn on the computer or exit a power saving mode (Standby or Hibernate) if one is active. For more information, see Using power saving modes.

Press the Eject button on the optical drive cover to open the drive tray. The drive tray slides out.

Ejecting the Drive Tray

Place a disc on the drive tray with the label facing up.

You can play some DVDs on both sides. Insert this type of DVD with the label you want to play facing up.

Inserting a Disc

Press the disc onto the tray until the disc clicks securely into place.

If you do not seat the disc firmly over the hub, the disc may come loose while it is in the drive. A loose

disc may damage the optical drive and make opening the drive tray difficult.

Push the drive tray gently to close it. The Busy indicator on the drive cover blinks while your computer is reading data from the drive.

To eject a disc

Turn on the computer or exit a power saving mode (Standby or Hibernate) if one is active. For more information, see Using power saving modes.

Close all programs that access the optical drive, and wait for the Busy indicator on the drive cover to turn off.

Press the Eject button on the drive cover to open the drive tray. The drive tray slides out.

If the Eject button does not work, turn off the computer and insert a thin, straight object (such as a paper clip)

Page 43

into the manual eject hole next to the Eject button.

Lift the disc from the drive.

Push the drive tray gently to close it.

Page 44

Copying and Playing CDs

Your computer comes equipped with a CD-RW/DVD drive, which plays DVD and most DVD-R discs, and reads and writes data to CD-R and CD-RW discs.

Playing CDs



Copying files to a CD-RW or CD-R



Page 45

Playing CDs

Before you play an audio CD, you may need to enable your computer's audio feature.

To enable the audio feature

Click Start on the Windows® taskbar, and then click Control Panel, Performance and Maintenance, and System. The System Properties dialog box appears.

As a shortcut, you can press Fn + the Windows key + Insert to open the System Properties dialog box.

Select the Hardware tab, and in the Device Manager box, click Device Manager. A window with a listing of the computer's hardware devices appears.

Double-click the type of the optical drive installed on the computer, such as DVD/CD-ROM drives1, to open the submenu.

Double-click the listed optical drive, and select the Properties tab.

Click to select the Enable digital CD audio for this CD-ROM device check box if it is not already selected.

Click OK.

To adjust the volume for playing CDs and DVDs

Some programs have built-in volume controls, which you can adjust. If there are no volume controls, then adjust the volume of your computer's built-in speakers by doing one of the following:

Using the Function keys. An on-screen display may appear, notifying you when a change occurs.



To increase volume, press the Fn and F4 keys, and then press or .



To decrease volume, press the Fn and F4 keys, and then press or .



Using the Volume icon.



Double click the Volume icon on the Taskbar Notification area. The Volume Control dialog box



appears.

In the Volume Control and Wave columns, move the Volume sliders up to increase volume and down to



decrease volume.

To play an audio CD

Insert the disc into the optical drive. See To insert a disc.

If nothing appears on the desktop once you insert an audio CD disc, then click Start, point to All Programs, and click to open a CD program, such as SonicStage. If the Audio CD window appears, click to select an option.

Audio CD

Page 46

O ptical drive types vary, depending on the model you purc has ed.

Page 47

Copying files to a CD-RW or CD-R

You can copy files to CD-R or CD-RW discs if your VAIO® computer is equipped with a CD-RW/DVD drive or DVD-RW drive. Before you write data to a CD-RW or CD-R disc, read the following notes to avoid a computer malfunction and ensure the best writing results:

Deactivate the screen saver and exit anti-virus software.



Deactivate memory-resident disc utilities to avoid data loss.



Disable the FindFast program if it is installed on your computer. Click Start and point to All Programs to see a list of



programs on your computer.

Connect and use the AC adapter to power your computer or make sure your battery is at least 50 percent charged.



See Powering Your Computer for more information.

To copy files to a CD-RW or CD-R

Insert a blank CD-R or CD-RWdisc into the optical drive. For more information, see Inserting and Ejecting CDs or

DVDs.

If the CD Drive window appears, click Take no action.

CD Drive

Open Windows Explorer by pressing the Windows key and the E key simultaneously.

In the Folders panel on the left, locate the file(s) or folder(s) you want to copy and either:

Right-click the file(s) or folder(s), point to Send To, and click the optical drive1 name.



Drag the file(s) or folder(s) onto the optical drive icon in the Files Stored on This Computer panel.



Close Windows Explorer.

Click Start, and My Computer.

Click the optical drive icon under Devices with Removable Storage. A new window appears with the file(s) or folder(s) you want to copy listed under Files Ready to Be Written to the CD.

In the CD Writing Tasks box, click Write these files to CD.

Follow the instructions on the CD Writing Wizard.

CD Writing Wizard

Page 48

Do not strike or shake the computer while writing data to a disc.

T he read/write drive letter des ignation may vary, depending on your s ystem's hardware configuration.

Page 49

Playing DVDs

You can play DVDs in your computer's optical drive and view the video on the computer screen.

Playing DVDs on your computer



Frequently asked questions



Page 50

Playing DVDs on your computer

Your computer is equipped with an optical drive that enables you to watch DVDs and most DVD-R discs on your computer.

To play a DVD while using AC power

Close all open programs.

Insert the DVD into the optical drive.

Open a preinstalled DVD program, such as WinDVD, by following these steps:

Click Start on the taskbar, and point to All Programs.

Select a program, such as InterVideo WinDVD 4, to play the DVD. For instructions on how to use a program, see the help guide included with the DVD program

To play a DVD while using battery power

Set the power management profile to DVD.

Close all open programs.

Right-click the CPU icon on the Taskbar Notification area.

Select Profiles from the shortcut menu, and then select DVD from the submenu. You can also select Automatic Profile Selection, which sets the power management profile to DVD whenever a DVD is

inserted into the optical drive. See Conserving Battery Power for more information.

Insert the DVD into the optical drive.

Open a preinstalled DVD program, such as WinDVD, by following these steps:

Click Start on the taskbar, and point to All Programs.

Select a program, such as WinDVD, to play the DVD. For instructions on how to use a program, see the help guide included with the DVD program.

Some discs recorded at 20 or 24 bits may produce noise while playing. If you have audio devices

connected, this may damage your hearing and the speakers. Reduce the volume before playing a DVD.

Do not switch power saving modes while the computer is playing a DVD.

Do not use memory-resident utility software to speed up disc access when playing a DVD. This may cause the computer to malfunction.

Page 51

Frequently asked questions

How do I maintain CDs and DVDs?

Avoid touching the surface of the disc with your fingers. Fingerprints and dust on the surface of the disc may cause



reading errors.

Try using canned compressed air to clean dusty discs.



Do not clean the disc with solvents (such as benzine, thinner, alcohol, commercially available cleaners, or anti-static



spray), which may damage the disc. To clean the disc, follow these steps:

Hold the edge of the disc, and use a soft cloth to wipe the surface from the center out.

If the disc is badly soiled, moisten a soft cloth with water, wring it out well, and use it to wipe the surface of the disc from the center out.

Wipe off any remaining moisture with a dry, soft cloth.

Do not drop or bend the disc.



Why does my computer freeze when I try to read a disc?

The disc your computer is trying to read may be dirty or damaged. Follow these steps:



Restart the computer by clicking Start, Turn Off Computer, and Restart.

Eject the disc from the optical drive.

Examine the disc for dirt or damage. If the disc is dirty, see How do I maintain CDs and DVDs? for instructions on how to clean it.

What do I do if the drive tray won't open?

Make sure the computer is on.



Press the Eject button on the optical drive.



If the Eject button does not work, click Start on the Windows® taskbar, and click My Computer. Right click the optical



drive icon, and select Eject from the shortcut menu.

If none of the above options work, insert a thin, straight object (such as a paper clip) in the manual eject hole to



the right of the Eject button.

Why won't the optical drive work?

If you are using the battery to power your computer, the battery profile may be set to Ultimate Battery Life. In order to extend battery life, this profile does not provide power to the optical drive. You can either customize the Ultimate Battery Life profile to provide power to the optical drive or select a different power management profile.

To customize the Ultimate Battery Life profile

Right-click the CPU icon on the Taskbar Notification area and select Edit/Create Profiles from the shortcut menu.

In the left panel, click Ultimate Battery Life.

In the right panel, right click Power-saving Mode and select Off.

To select a different power management profile

Right-click the CPU icon on the Taskbar Notification area.

Point to Profiles, and click to select a profile from the menu.

For more information about power management profiles, see Using PowerPanel utility.

Page 52

What do I do if the optical drive isn't playing my CD or DVD properly?

Make sure the disc was inserted into the drive with the label facing up.



Make sure the necessary program(s) is installed according to the manufacturer's instructions.



If the CD or DVD is dirty or damaged, the computer will stop responding. Follow these steps:



Restart the computer by pressing Ctrl+Alt+Delete, and selecting Restart from the Shut Down menu of the Windows Task Manger dialog box.

Remove the CD or DVD from the optical drive.

Check the disc for dirt or damage. If you need to clean the disc, see How do I maintain CDs and DVDs? for instructions.

If you are playing a CD or DVD and cannot hear sound, follow these steps:



Double-click the Volume icon on the Taskbar Notification area, and click to cancel the Volume Control and CD Audio Mute check boxes.

Check the volume setting in the audio mixer.

If you are using external speakers, check the volume settings on the speakers and the connections between the speakers and the computer.

Make sure the CD audio feature is enabled and the correct driver software is installed. Follow these steps:

Click Start on the Windows® taskbar, click Control Panel, Performance and Maintenance, and System. The System Properties window appears.

Select the Hardware tab, and click Device Manager in the Device Manager box. A window with a listing of the computer's hardware devices appears.

If a "X" or an exclamation point appear on the listed device, you may need to enable the device or reinstall the drivers.

Double-click the optical drive to open the submenu.

Double-click the listed drive name, and select the Properties tab.

Click to select the Enable digital CD audio for this CD-ROM device check box, if it is not selected.

You can confirm the driver software by selecting the Driver tab, and clicking Driver Details.

Click OK to close the window.

Make sure an adhesive label was not attached to the CD or DVD. Adhesive labels can come off while the disc is in



the optical drive and damage the drive or cause it to malfunction.

If a region code warning appears, the disc may be incompatible with the optical drive. Check the DVD package to



make sure the region code is compatible with the optical drive.

If you notice condensation on the computer, do not use the computer for at least one hour. Condensation can



cause the computer to malfunction.

Why did the computer screen (LCD) go blank?

Your computer screen may go blank if the computer has lost power or has entered a power saving mode (Standby



or Hibernate). If the computer is in LCD (Video) Standby mode, press any key to activate the computer screen. See

Using power saving modes for more information.

Make sure the computer is plugged into a power source and is on. The power indicator on the computer will be on if



the computer is on.

If your computer is using battery power, make sure the battery is inserted properly and is charged. See Using the



Battery for more information.

Page 53

If the display mode is set to external display, use the Fn+F7 key combination. See Selecting a display for more



information.

Page 54

Printer Connections

Printing With Your Computer



Page 55

Printing With Your Computer

Your computer is compatible with many popular printers. However, to ensure the best performance, printers must be compatible with the Microsoft® Windows® operating system installed on your computer.

Connecting a printer



Disconnecting a printer



Frequently asked questions



Page 56

Connecting a printer

You can easily connect a printer to your computer or port replicator (if applicable). The New Hardware Wizard enables you to easily install the printer software, but some printers require separate driver software installation. See the instructions that accompanied your printer for more information.

To connect a USB printer

Plug the USB cable into the USB port on your computer. See "Locating Controls and Ports" in the "Setting Up" chapter of your printed VAIO® Computer Quick Start.

Plug the other end of the USB cable into the USB port on the printer.

Turn the printer on. The Found New Hardware Wizard appears on the computer screen.

Connecting a USB Printer

See the guide that accompanied the printer for more information on its installation and use.

To connect a printer (port replicators only)

Plug the printer cable into the Printer port on your port replicator. See Locating Ports and Jacks.

Plug the other end of the printer cable into the port on the printer.

Connecting a Printer

Page 57

Restart your computer by clicking Start, Turn Off Computer, and Restart. If the New Hardware Wizard appears, follow the on-screen instructions.

Make sure the computer recognizes the printer. Follow these steps:

Click Start, Control Panel, Printers and Other Hardware, and then Printers and Faxes.



If the computer recognizes the printer, it will be listed in the Printers and Other Hardware window. If the computer does not recognize the printer, you may need to install the printer driver software. See the guide that accompanied the printer for more information.

See the guide that accompanied the printer for more information on its installation and use.

Page 58

Disconnecting a printer

You can disconnect the printer cable when the computer is on or off. Disconnecting a printer when the computer is in a power saving mode (Standby or Hibernate) may cause the computer to malfunction.

To disconnect a printer

Make sure all printing jobs are completed.

Unplug the printer cable from the computer.

Page 59

Frequently asked questions

Why can't I print a document?

Make sure the printer is on, and the printer cable is securely connected to the ports on your printer and computer.



See Connecting a printer for more information.

Make sure the printer is compatible with the Microsoft® Windows® operating system installed on your computer.



You may need to install the printer driver software before you use the printer. See the guide that accompanied the



printer for more information.

If the printer is not functioning after the computer resumes from a power saving mode (Standby or Hibernate), then



restart the computer.

If the bidirectional communication functions are provided with your printer, disabling the functions on your computer



may enable printing. Follow these steps:

Click Start, and then Control Panel.

Click Printers and Other Hardware.

Click Printers and Faxes.

Right-click an unused printer and select Properties.

Click the Ports tab.

Click to cancel the Enable bidirectional support check box.

Click OK.

This change to the settings disables the bidirectional communication functions of your printer, such as data transfer, status monitoring, and remote panel.

Page 60

Computer Features

Using the Touch Pad



Using Memory Stick Media



Using the Multilingual User Interface Language Option



Changing the Window Design of Sony Programs



Page 61

Using the Touch Pad

A pointing device called a touch pad is located in front of the keyboard. You can point to, select, drag, and scroll objects on the screen using the built-in touch pad.

Describing the touch pad



Customizing the touch pad



Frequently asked questions



Page 62

Describing the touch pad

Locating the Touch Pad

Touch Pad Action Description

Sliding one finger Equivalent to using a mouse to place the pointer on an item.

Tapping once Equivalent to pressing the left button once.

Tapping twice Equivalent to pressing the left button twice.

Sliding one finger while pressing the left button Equivalent to using the mouse to drag an item.

Moving your finger along the right edge of the touch pad Equivalent to scrolling vertically. (The scroll function is available only with programs that support a touch pad scroll feature.)

Moving your finger along the bottom to scroll horizontally Equivalent to scrolling horizontally. (The scroll function is available only with programs that support a touch pad scroll feature.)

Page 63

Customizing the touch pad

Sony Notebook Setup lets you customize, enable, or disable the touch pad. Open the Mouse Properties dialog box to set your touch pad and mouse preferences, such as changing pointers, enabling or disabling the tapping feature, clicking both buttons simultaneously, and adjusting the touch pad speed.

To customize the touch pad and mouse

Right-click the Touchpad icon on the Windows® taskbar, and click Mouse Properties from the shortcut menu.



The Mouse Properties dialog box appears.

To enable the touch pad

Press the Windows key . The Start menu appears.

Press P until All Programs is selected, and press Enter.

Press S until Sony Notebook Setup is selected, and press Enter. A submenu appears with Sony Notebook Setup preselected.

Press Enter. The Sony Notebook Setup dialog box appears.

Press the Right Arrow key to select the Device tab.

Press the Tab key to select the Default button, and press Enter. A pop-up window appears.

Press the Left Arrow key to select OK, and press Enter. The Enable Touchpad option is automatically selected.

Press the Tab key to select the Apply button, and press Enter.

Click OK.

To disable the touch pad

Click Start on the Windows® taskbar, and point to All Programs.

Point to Sony Notebook Setup, and click Sony Notebook Setup in the submenu. The Sony Notebook Setup dialog box appears.

Click the Device tab.

In the left panel, click to cancel the Pointing Device check box.

Click Apply. A Sony Notebook Setup message appears.

Click Yes.

Page 64

Frequently asked questions

What do I do if the touch pad does not work?

Try restarting your computer. Follow these steps:



Press the Windows key .

Press U. The Turn off computer window opens.

Press R to restart the computer.

If the computer does not restart,



Press the Ctrl+Alt+Delete keys simultaneously. The Windows Task Manager window appears.

Press and release Alt to highlight the menu bar, and press the Right Arrow key to select Shut Down .

Press Enter.

Press R to restart the computer.

If you still cannot restart your computer, press and hold the power button to turn off the computer.



If the pointer does not move while playing a disc, press Ctrl+Alt+Delete simultaneously to stop playback and



restart the computer.

If you are still experiencing problems, make sure another mouse is not installed.



You may have disabled the touch pad without connecting a mouse to the computer. See To enable the touch pad.



How do I change the left and right button assignments?

If your computer is interpreting a single-click as a double-click, you may want to change the button assignments. Follow these steps:

Click Start on the Windows® taskbar and click Control Panel and Printers and Other Hardware and Mouse. The Mouse Properties dialog box appears.

On the Buttons tab, select your preferences in the Button Selection box.

Click Apply to install your settings.

Click OK to close the window.

Page 65

Using Memory Stick Media

This compact, portable, and versatile recording medium has a data capacity exceeding that of a floppy disk. Memory Stick media is specially designed for exchanging and sharing digital data with compatible products. Because it is removable, the media can be used for external data storage.

Selecting Memory Stick media



Inserting Memory Stick media



Viewing the contents



Write-protecting Memory Stick media



Formatting Memory Stick media



Removing Memory Stick media



Frequently asked questions



Page 66

Selecting Memory Stick media

Your VAIO® computer is equipped with a Memory Stick® slot that supports certain types of Memory Stick® media.

Page 67

About Memory Stick media

Memory Stick® media are a compact, portable, and versatile data storage media designed for exchanging and sharing digital data with compatible devices. The following types of Memory Stick media are available, but compatibility with your computer can vary.

MagicGate Memory Stick media (MG Memory Stick media) — Provides copyright protection with authentication and



encryption, using Sony® MagicGate technology. Authentication ensures that protected content is only transferred between compliant devices and media. Protected content can be recorded and transferred in an encrypted format to prevent unauthorized duplication or playback. You can store different data formats on a single Memory Stick media.

Memory Stick PRO media — Provides MagicGate copyright protection and high-speed transfer features when used



with compatible Memory Stick PRO devices. VAIO® computers support Memory Stick PRO media for data storage purposes only. Currently, high-speed data transfer and the MagicGate technology features, such as authentication and encryption, are not available. You can store different data formats on a single Memory Stick media.

Memory Stick media — Provides data storage only. The Memory Stick media does not provide MagicGate technology



or high-speed data transfer. You can store different data formats on a single Memory Stick media.

Currently, Sony® SonicStage and OpenMG software are not compatible with the new Memory Stick PRO media. Sony suggests using only MG Memory Stick media to store and transfer any data created with SonicStage or OpenMG software.

Visit the Sony Computing Support Web site at http://www.sony.com/pcsupport regularly for the latest information on the new Memory Stick PRO media.

Memory Stick media do not support video file playback directly from the media. Copy the video file to your hard disk drive and then play back the file.

Page 68

Inserting Memory Stick media

The media slot accommodates only one Memory Stick media at a time.

To insert Memory Stick media

Insert the Memory Stick media with the arrow facing up and toward the Memory Stick media slot.

Inserting the media in the wrong direction may damage the connector pins.

Carefully slide the Memory Stick media into the slot until it clicks in place. The Memory Stick media indicator briefly blinks.

Inserting Memory Stick Media

Page 69

Viewing the contents

Depending on the model you purchased, the Sony Memory Stick window may appear when you insert a Memory Stick

media. From this window, you can choose to view, print, copy or organize your Memory Stick images or data. If the Sony Memory Stick window does not appear when you insert your Memory Stick media, then follow these steps:

To view the contents

From the Start menu, click My Computer. The My Computer window appears.

Click Sony MemoryStick. The Sony MemoryStick window appears, displaying the contents stored on the Memory Stick media.

Page 70

Write-protecting Memory Stick media

Memory Stick® media is designed with a write-protect tab to protect data from accidental erasure or overwriting. Move the tab to the right or left to set or release write-protection. When the write-protect tab of the Memory Stick media is set to LOCK, data cannot be recorded or erased.

Write-protect off Data can be saved on the Memory Stick media.

Write-protect on Data can be read from but not saved on the Memory Stick media.

Using the Write-Protect Tab

Page 71

Formatting Memory Stick media

Memory Stick® media is formatted for immediate use when you purchase it. If you need to reformat Memory Stick media, use the Memory Stick Formatter that is provided with the media. For more information about using Memory Stick Formatter, refer to Formatter Help.

Formatting Memory Stick media erases all data, including music data, previously saved to it. Before you

reformat Memory Stick media, confirm that the media does not contain files you want to keep. Back up important data before formatting the media.

To format Memory Stick media

Insert the Memory Stick media into the Memory Stick media slot. See To insert Memory Stick media for more information.

From the Start menu, click My Computer. The My Computer window appears.

Right-click Sony MemoryStick, and click Format from the menu. The Format Sony MemoryStick dialog box appears.

Select Quick Format in the Format options box, and then click Start.

Page 72

Removing Memory Stick media

If the Memory Stick® media is removed prematurely, a blue screen with a message may appear prompting you to continue or exit. Reinsert the media into the slot and press Enter to continue. This enables the media to finish reading or writing data.

To remove Memory Stick media

Wait a minimum of 10 seconds after the Memory Stick media finishes reading or writing data before removing the media.

Make sure the access light is off.

Push the Memory Stick media in toward the computer.

When the Memory Stick media ejects, pull it out.

Be careful when removing the Memory Stick media, as it may not eject completely from the slot.

Page 73

Frequently asked questions

Why can't I open my image files?

You may need to reformat your Memory Stick media.

Formatting Memory Stick media erases all data, including music data, previously saved to it. Before you

reformat Memory Stick media, back up important data and confirm that the media does not contain files you want to keep.

Copy the data from the Memory Stick media onto your computer's hard disk to save data or images.

Format the Memory Stick media using Memory Stick Formatter software preinstalled on your computer. For instructions about formatting a Memory Stick media, see Formatting Memory Stick media.

Why can't I save music files onto my Memory Stick media?

Only MagicGate Memory Stick media can be used with copyright protected data, such as music.



Using recorded music requires permission of the copyright holders.



Sony is not responsible for music files that cannot be recorded from a CD or downloaded from other sources.



Can I copy images from a digital video camera using Memory Stick media?

Yes, and you can view video clips that you have recorded with Memory Stick media-compatible video camera recorders.

How do I prevent damage to the Memory Stick media?

Do not use the media in locations that are subject to static electricity or electrical noise.



Do not touch the media connector with your finger or metallic objects.



Do not attach labels other than the supplied label to a media.



Do not bend, drop, or apply strong shock to the media.



Do not disassemble or modify the media.



Do not allow the media to get wet.



How do I extend the life of the Memory Stick media?

Use the supplied storage case. See the instructions that came with your media for more information on its use.



Do not use or store the media in a location that is subject to:



Extremely high temperatures, such as in a car parked in the sun



Direct sunlight



High humidity or places with corrosive substances



Page 74

Using the Multilingual User Interface Language Option

(Microsoft® Windows® XP Professional only) After you have initially setup your new VAIO® computer, you can change the language displayed in Microsoft® Windows® XP Professional operating system. The multilingual user interface (MUI) language option changes the text controlled by Windows XP Professional operating system. Menus, help files, and icons generated by Windows XP Professional are shown in your selected language. All other programs are displayed in English as the default language.

The multilingual user interface language option is not designed to replace a localized version of the Microsoft Windows® XP Professional operating system. Under certain conditions, some third-party software applications may not function properly.

To Change the Language Option

Click Start on the Windows® taskbar, and then click Control Panel.

Click Date, Time, Language and Regional Options, and then click Regional and Language Options. The Regional and Language Options dialog box appears.

Click the Languages tab.

From the Language used in menus and dialogs shortcut menu, select the desired language:

English



francais



Português



español



Click Apply. The Change Regional Options pop-up window appears.

Click OK.

Click Start on the Windows® taskbar, and then click Logoff.

Additional users can also change to their desired language(s) without affecting your existing language settings.

Page 75

Changing Numbers, Currency, Time, and Date Formats

You can change your operating system's number, currency, time, and date formats to coordinate with your chosen country or language settings.

To change these formats

Click Start on the Windows taskbar, and then click Control Panel.

Click Date, Time, Language and Regional Options, and click Regional and Language Options. The Regional and Language Options dialog box appears.

From the Regional Options tab, click the Standards and formats shortcut menu to view the available country choices. Select the desired country.

Click Customize to change the number, currency, time, and date settings.

Click OK.

Page 76

Changing the Window Design of Sony Programs

This feature changes the appearance, such as color, of certain Sony programs.

To change the window design

Click Start, and then Control Panel.

In the left panel, click Switch to Classic View.

Double-click UI Design Selector.

Click << or >> to view the designs.

Click Apply to select a design that appears in the center window. The UI Design Selector window design changes. The window design for your Sony software will match the UI Design Selector window.

Click OK.

Page 77

Mice and Keyboards

Using the Keyboard



Connecting External Mice and Keyboards



Page 78

Using the Keyboard

Your keyboard is very similar to a typewriter's, but your computer keyboard has additional keys that perform specific computer-related tasks.

Key descriptions



Combinations and functions with the Windows key



Indicator Lights



Combinations and functions with the Fn key



Page 79

Key descriptions

Key Description

Numeric keypad

Contains the keys found on a typical calculator. Use the numeric keypad area to type numbers or to perform mathematical calculations, such as addition and subtraction. Numbers appear on the front beveled edge of the numeric keys. Press the Num Lock key to activate the numeric keypad. (When you do so, the Num Lock indicator light turns on.) Press the Num Lock key again to deactivate the numeric keypad.

Arrow keys

The Left, Right, Up, and Down arrow keys move the pointer on the screen. They also function as the Home, End, Page Up, and Page Down keys, respectively, when the Fn key is pressed.

Correction keys

The Insert, Back Space, and Delete keys enable you to make corrections to keystrokes.

Function keys

The 12 function keys along the top of the keyboard are used to perform designated tasks. For example, in many programs, F1 is the Help key. The task associated with each function key may vary from one program to the next.

Escape key

The Esc (Escape) key is used to cancel commands.

Print Screen key

The Print Screen key takes an electronic snapshot of the screen and moves it to the Clipboard. You can then paste the screen shot into a document and print it.

Operator keys

Page 80

(Ctrl, Alt, Shift keys)

Several keys are always used with at least one other key: Ctrl, Alt, and Shift. When held down with another key, the Ctrl (Control) and Alt (Alternate) keys offer another way to give commands. For example, in many programs, instead of choosing the Save command from a menu, you can hold down Ctrl and press S (referred to as Ctrl+S ). The Shift key operates the same way as on a typewriter; it is used to produce capital letters or special symbols, such as @ and $.

Windows key

The key with the Microsoft® Windows® operating system logo displays the Start menu; it is the equivalent of clicking Start on the taskbar. See Combinations and functions with the Windows key for more information. Fn key

The Fn key is used in combination with other keys to issue commands. See Combinations and

functions with the Fn key for more information.

Applications key

The Applications key displays a shortcut menu of context-sensitive choices. Pressing this key is the equivalent of clicking the right mouse button.

Page 81

Combinations and functions with the Windows key

Combination Function

+F1 Displays the VAIO Help and Support Center window.

+Tab Switches the selected button on the taskbar.

+D Displays the desktop.

+E Displays the Windows Explorer window.

+F Displays the Search Results window, where you can find a file or folder. This is the equivalent of selecting

Search from the Start menu.

+Ctrl+F Displays the Search Results - Computers window, where you can locate other computers. This is the

equivalent of selecting Search, and then Computer from the Start menu.

+M Minimizes all displayed windows.

Shift+ +M Returns all minimized windows to their previous size.

+R Displays the Run window. This is the equivalent of selecting Run from the Start menu.

Fn+ +Insert Displays the System Properties window. This is the equivalent of selecting Control Panel, and then System from the Start menu.

Page 82

Indicator Lights

Indicator Function

Power

Turns on when the power to the computer is on, blinks in Standby mode, and turns off when the computer is in Hibernate mode or off. Battery

Turns on when the computer is using battery power, blinks when the battery is running out of power, double-blinks when the battery is charging. Memory Stick®

Turns on when data is read from or written to the Memory Stick media. (Do not enter Standby mode or turn off the computer when this indicator is on.) When the indicator is off, the Memory Stick media is not being used. Hard Disk

Turns on when data is read from or written to the hard disk. Do not enter Standby mode or turn off the computer when this indicator is on. Num Lock

Press this key to activate the numeric keypad. Press it a second time to deactivate the numeric keypad. The numeric keypad is not active when the indicator is off. Caps Lock

Press this key to type letters in uppercase. Letters appear in lowercase if you press Shift while the indicator is on. Press the key a second time to turn off the indicator. Normal typing resumes when the Caps Lock indicator is off. Scroll Lock

Press this key to change how you scroll the display. Normal scrolling resumes when the Scroll Lock indicator is off. The Scroll Lock key functions differently depending on the program you are using and does not work with all programs. Wireless LAN1 Turns on when the wireless LAN function is running.

O n selected models only.

Page 83

Combinations and functions with the Fn key

Combinations/

Feature Function

Fn+F3 Toggles the built-in speakers off and on.

Fn+F4 Adjusts the built-in speaker volume. An on-screen display appears notifying you when a change occurs.

To increase volume, press Fn+F4 and then press or .

To decrease volume, press Fn+F4 and then press or .

Fn+F5 Adjusts the brightness of the computer screen (LCD).

To increase brightness, press Fn+F5 and then press or .

To decrease brightness, press Fn+F5 and then press or .

Fn+F7 Toggles the display between the computer screen (LCD), a connected external device, such as a monitor or projector, and both the LCD and external device.

Select one display at a time when playing a DVD. Connect the cable before you turn on the computer; otherwise, Fn+F7 will not work. Fn+F12 Puts the system into Hibernate mode, a power management state. To return the system to normal operating mode, press the power button. Hibernate mode consumes the lowest level of power. Fn+Esc Puts the system into Standby mode, a power management state. To return the system to the active state, press any key or the power button.

Page 84

Connecting External Mice and Keyboards

Your computer is compatible with many popular mice and keyboards. To function properly, the device you connect must be compatible with the Microsoft® Windows® operating system installed on your computer. For information about your computer's built-in keyboard and key functions, see Key descriptions.

Connecting a mouse or keyboard



Disconnecting a mouse or keyboard



Frequently asked questions



Page 85

Connecting a mouse or keyboard

Your computer can be on or off when connecting a universal serial bus (USB) mouse or keyboard. If you connect the mouse or keyboard when the computer is on, you may need to restart the computer for it to recognize the device. See Frequently

asked questions for more information.

To connect a USB mouse or keyboard to your computer

Plug the USB cable into the USB port . See "Locating Controls and Ports" in the "Setting Up" chapter of your printed VAIO® Computer Quick Start. (One USB port supports one USB connection.)

If the New Hardware Wizard appears, follow the on-screen instructions to complete the installation process.

Although the New Hardware Wizard guides you through the software installation, some devices require separate driver software installation. See the instructions that accompanied your mouse or keyboard for more information

Connecting a USB Mouse or Keyboard

Page 86

Disconnecting a mouse or keyboard

You can disconnect a USB mouse or keyboard when the computer is on or off. Disconnecting the mouse or keyboard when the computer is in a power saving mode (Standby or Hibernate) may cause the computer to malfunction.

To disconnect a mouse or keyboard

Unplug the USB cable from the USB port.



Page 87

Frequently asked questions

What do I do if the computer doesn't recognize the mouse?

Make sure the mouse is securely plugged into the port. See Connecting a mouse or keyboard for more information.



Restart the computer with the mouse connected to the computer.



What do I do if the pointer doesn't move when I use the mouse?

Make sure another mouse is not installed.



If you are playing a disc, press the Ctrl+Alt+Delete keys simultaneously to stop playback and restart the computer.



If you still cannot use the pointer, restart the computer. You can restart the computer three different ways:



Press the Windows key , and press U. When the Turn Off Computer window appears, press R.



Press the Ctrl+Alt+Delete keys simultaneously. When the Windows Task Manager window appears, press



the Alt key to highlight the menu bar, and press the Right Arrow key to select Shut Down. Press Enter, and then press R.

Press and hold the power button. When the computer turns off, press the power button again to restart the



computer.

Page 88

Floppy Disks and PC Cards

Using a Floppy Disk Drive



Using PC Cards



Page 89

Using a Floppy Disk Drive

You can connect a floppy disk drive to your computer. The floppy disk drive enables you to read or write data to a floppy disk.

Connecting a floppy disk drive



Inserting and removing floppy disks



Protecting floppy disks



Disconnecting a floppy disk drive



Storing a floppy disk drive



Frequently asked questions



Page 90

Connecting a floppy disk drive

You can connect a floppy disk drive when your computer is on or off. Connecting the drive when the computer is in a power saving mode (Standby or Hibernate) may cause the computer to malfunction.

To connect a USB floppy disk drive

Close any active programs to prevent data loss.

Plug the USB cable (with the USB icon facing upward) into the USB port . The Found New Hardware pop-up message appears.

Connecting a Floppy Disk Drive

Page 91

Inserting and removing floppy disks

To write data to a disk, use one that is not write-protected or disable the write-protect feature. The floppy disk drive cannot write data to a disk if it is inserted into the drive improperly.

To insert a floppy disk

Hold the floppy disk with the label facing up.

Push the floppy disk into the drive until it clicks into place.

Inserting a Floppy Disk

Do not open the shutter manually and touch the surface of the floppy disk.

To remove a floppy disk

Close all programs that access the floppy disk.

Wait for the LED indicator on the floppy disk drive to turn off.

Push the Eject button, and remove the disk.

To avoid losing data, do not push the Eject button when the LED indicator is on.

Remov ing a Floppy Disk

Page 92

Protecting floppy disks

Do not open the shutter manually or touch the surface of the floppy disk.



Keep floppy disks away from magnets, direct sunlight, and heat sources.



Page 93

Disconnecting a floppy disk drive

You can disconnect a USB floppy drive when the computer is off by disconnecting the USB cable from the computer. Disconnecting the drive when the computer is in a power saving mode (Standby or Hibernate) may cause the computer to malfunction.

To disconnect a USB floppy drive while the computer is on

Double-click the Safely Remove Hardware icon on the taskbar. The Safely Remove Hardware dialog box appears.

Click to select the floppy drive in the Hardware devices window, if it is not already selected.

Click Stop. The Stop a Hardware device window appears.

Make sure the floppy drive is selected, and click OK. A message appears stating it is safe to remove the hardware device.

Page 94

Storing a floppy disk drive

Fold the floppy disk drive cable and connector into the side compartment on the floppy disk drive.

Storing a Floppy Disk Drive

Page 95

Frequently asked questions

Why doesn't the Safely Remove Hardware icon appear on the taskbar when the drive is connected?

The computer does not recognize the floppy disk drive. First, make sure the USB cable is properly connected to the USB port. If you need to secure the connection, wait a few moments for the computer to recognize the drive. If the icon still does not appear, follow these steps:

Close all programs that were accessing the floppy disk drive.

Wait for the LED indicator on the floppy disk drive to turn off.

Push the Eject button, and remove the disk.

Reconnect the floppy disk drive by inserting the USB connector (with the USB icon facing upward) into the USB

port .

Restart the computer by clicking Start on the Windows® taskbar, Turn Off Computer, and then Restart.

Why is the drive unable to write data to a floppy disk?

Make sure the floppy disk is properly inserted in the drive. See Inserting and removing floppy disks for instructions on how to insert the disk properly.

If the disk is inserted properly and you are still unable to write data to it, the disk may be full or write-protected. You can either use a floppy disk that is not write-protected or disable the write-protect feature by moving the write-protect tab on the bottom of the disk to the close position.

Page 96

Using PC Cards

Your computer includes one or more PC Card slots. A PC Card enables you to connect devices such as an optical drive, floppy disk drive, or Network Interface Card (NIC).

See your VAIO® Computer Specifications for the type of PC Card that is compatible with your computer. These slots are compatible with CardBus. If your computer has more than one PC Card slot, use the lower slot for Type III PC Cards. You do not need to turn off your computer to insert or remove a PC Card.

Inserting PC Cards



Removing PC Cards



Connecting and disconnecting PC Card drives



Frequently asked questions



Page 97

Inserting PC Cards

Your computer may contain PC Card slot protectors. Remove these protectors before you insert a PC Card into the slot. See To remove slot protectors.

Some PC Cards may require you to disable idle devices when using the PC Card. You can use Sony Notebook Setup to disable these devices.

To open Sony Notebook Setup

Click Start on the Windows taskbar, and then click All Programs.

Point to Sony Notebook Setup, and click Sony Notebook Setup. The Sony Notebook Setup dialog box appears.

To insert a PC Card

Make sure the front label of the PC Card is facing up.

Push the PC Card gently into the slot. The system automatically detects the PC Card.

Do not force a PC Card into the slot; this may damage the connector pins.

When a PC Card is inserted, do not place your computer in a bag or case. Pressure or shock to a PC Card may damage your computer.

Touching the head of the PC Card will not damage the connector pins, but damage may occur if the head of the PC Card is sticking out of the PC Card slot while the computer is being transported.

Inserting a PC Card

Page 98

Removing PC Cards

You can remove PC Cards while the computer is on or off. PC Cards draw power from the computer when they are inserted into the PC Card slot, whether or not you use the card.

If you are not using your PC Card and you are using a battery as a power source, remove the PC Card from the PC Card slot to conserve battery power.

To remove a PC Card while your computer is on

Double-click the Safely Remove Hardware icon on the taskbar. The Safely Remove Hardware dialog box appears.

Click to select the PC Card in the Hardware devices window, if it is not already selected.

Click Stop. The Stop a Hardware device window appears.

Make sure the PC Card is selected, and click OK. A message appears stating it is safe to remove the hardware device.

Push the Release button. The Release button pops out.

Push the Release button a second time. The PC Card pops out.

Gently pull the card out of the slot.

To remove a PC Card while the computer is off

Push the Release button once. The Release button pops out.

Push the Release button a second time. The PC Card pops out.

Gently pull the card out of the slot.

To remove slot protectors

Push the Release button once. The Release button pops out.

Push the Release button a second time. The slot protector pops out.

Pull the protector out of the slot.

Page 99

Connecting and disconnecting PC Card drives

The PC Card drive enables you to read data stored on a DVD or CD. Your computer may come with an external PC Card drive, depending on the model you purchased. If you wish to purchase a PC Card drive, shop Sony online at

http://www.sonystyle.com/vaio or contact your local retailer.

If you connect a non-Sony DVD drive to your VAIO® computer, DVD playback may not function properly. The

supplied DVD software must be installed to play a DVD. For best performance, use a Sony compatible DVD drive.

To connect a PC Card drive

You can connect a PC Card drive while the computer is on or off. Connecting the drive when the computer is in a power saving mode (Standby or Hibernate) may cause the computer to malfunction.

Instructions on connecting an optical drive may vary, depending on the specific drive you purchased.

Remove the PC Card from the bottom of the optical drive.

Remov ing a PC Card

Insert the PC Card into the PC Card slot with the arrow facing the slot. See To insert a PC Card for more information.

Remove the protective cover that is attached to the lens of the optical drive before you use the drive. See Inserting

and Ejecting CDs or DVDs for information on how to open the optical drive to access the lens.

See the guide that accompanied your optical drive for more information on its installation and use.

To disconnect a PC Card drive

Close all programs accessing the PC Card drive.

Double-click the Safely Remove Hardware icon on the taskbar. The Safely Remove Hardware window appears.

Select the PC Card drive in the Hardware devices window, if it is not already selected.

Click Stop. The Stop a Hardware device window appears.

Make sure the PC Card drive is selected, and click OK. A message appears stating it is now safe to remove the hardware device.

Eject the PC Card from the PC Card slot.

Page 100

Sony PCG-V505BCK, PCG-V505BCP, PCG-V505BX, PCG-V505BXP User Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Welcome

Powering Your Computer

Using AC Power

Connecting the AC adapter

Turning on the computer

Using the Battery

Inserting a battery

Removing a battery

Locating battery information

Charging a battery

Notes on batteries

Frequently asked questions

Conserving Battery Power

Using power saving modes

Using PowerPanel utility

Frequently asked questions

Internet and Network Connections

Internet Connections

Setting up a dial-up Internet connection

Setting up an Ethernet Internet connection

Customizing your Internet connection

Frequently asked questions

Network Connections

Using Ethernet and dial-up connections

Using wireless network connections (selected models only)

Checking your network connection status

Frequently asked questions

Connecting Another VAIO Computer

Connecting VAIO computers

Disconnecting VAIO computers

Frequently asked questions

CDs and DVDs

Inserting and Ejecting CDs or DVDs

Copying and Playing CDs

Playing CDs

Copying files to a CD-RW or CD-R

Playing DVDs

Playing DVDs on your computer

Frequently asked questions

Printer Connections

Printing With Your Computer

Connecting a printer

Disconnecting a printer

Frequently asked questions

Computer Features

Using the Touch Pad

Describing the touch pad

Customizing the touch pad

Frequently asked questions

Using Memory Stick Media

Selecting Memory Stick media

About Memory Stick media

Inserting Memory Stick media

Viewing the contents

Write-protecting Memory Stick media

Formatting Memory Stick media

Removing Memory Stick media

Frequently asked questions

Using the Multilingual User Interface Language Option

Changing Numbers, Currency, Time, and Date Formats

Changing the Window Design of Sony Programs

Mice and Keyboards

Using the Keyboard

Key descriptions

Combinations and functions with the Windows key

Indicator Lights

Combinations and functions with the Fn key

Connecting External Mice and Keyboards

Connecting a mouse or keyboard

Disconnecting a mouse or keyboard

Frequently asked questions

Floppy Disks and PC Cards

Using a Floppy Disk Drive

Connecting a floppy disk drive

Inserting and removing floppy disks

Protecting floppy disks