• Design and specifications are subject to
change without notice.
S400
9-876-364-05
本機の仕様および外観は、改良のため予告なく変更
•
することがあります が 、ご了承ください。
NOTEBOOK COMPUTER
Information in this document is subject to
change without notice.
Sony, VAIO and CLIE are trademarks or registered trademarks of Sony. Microsoft,Windows,
Windows Media, Outlook, Bookshelf and other
Microsoft products are trademarks or registered
trademarks of Microsoft Corporation in the
United States and other countries.The word
Bluetooth and the Bluetooth logo are trademarks
of Bluetooth SIG, Inc. AMD, AMD logo, AMD
Duron and combinations there of, 3DNow!, are
trademarks of Adv anced Micro Devices, Inc. Intel
Inside logo, Pentium and Celeron are trademarks
or registered trademarks of Intel Corporation.
Transmeta, the Transmeta logo, Crusoe Processor, the Crusoe logo and combinations there of
are trademarks of Transmeta Corporation in the
USA and other countries. Graffiti, HotSync,
PalmModem, and Palm OS are resistered trademarks, and the Hotsync logo and Palm are trademarks of Palm,Inc. or its subsidiaries. (M) and
Motrola are trademarks of Motrora, Inc. Other
Motrola products and services with (R) mark like
Dragomball are the trademarks of Motrola, Inc.
All other names of systems, products and
servicesin this manual are trademarks or registered trademarks of their respective owners. In
this manual, the (TM) or (R) mark are not specified.
Caution Markings for Lithium/Ion Battery - The
following or similar texts shall be provided on
battery pack of equipment or in both the operating and the service instructions.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer. Discard used batteries according to the
manufacturer’s instructions.
CAUTION: The battery pack used in this device
may present a fire or chemical burn hazard if
mistreated. Do not disassemble, heat above
100ºC (212ºF) or incinerate. Dispose of used battery promptly. Keep away from children.
CAUTION: Changing the back up battery.
•Overcharging, short circuiting, reverse charging, multilati on or incineration of the cells must
be avoided to prevent one or more of the following occurrences; release of toxic materials,
release of hydrogen and/or oxygen gas, rise in
surface temperature.
• If a cell has leaked or vented, it should be replaced immediately while avoiding to touch it
without any protection.
Service and Inspection Precautions
1. Obey precautionary markings and
instructions
Labels and stamps on the cabinet, chassis, and
components identify are as requiring special precautions. Be sure to observe these precautions,
as well as all precautions listed in the operating
manual and other associated documents.
2. Use designated parts only
The set’s components possess important safety
characteristics, such as noncombustibility and the
ability to tolerate large voltages. Be sure that replacement parts possess the same safety characteristics as the originals. Also remember that the
0 mark, which appears in circuit diagrams and
parts lists, denotes components that have particularly important safety functions; be extra sure to
use only the designated components.
3. Always follow the original
designwhen mounting parts and
routing wires
The original layout includes various safety features, such as inclusion of insulating materials
(tubes and tape) and the mounting of parts above
the printer board. In addition, internal wiring has
been routed and clamped so as to keep it away
from hot or high-voltage parts. When mounting
parts or routing wires, therefore, be sure
toduplicate the original layout.
4. Inspect after completing service
After servicing, inspect to make sure that all
screws, components, and wiring have been returned to their original condition. Also check the
area around the repair location to ensure that repair work has caused no damage, and confirm
safety.
5. When replacing chip components...
Never reuse components. Also remember that
the negative side of tantalum capacitors is easily
damaged by heat.
6. When handling flexible print
boards...
• The temperature of the soldering-iron tip
should be about 270ºC.
• Do not apply the tip more than three times to
the same pattern.
• Handle patterns with care; never apply force.
Caution: Remember that hard disk drives
areeasily damaged by vibration. Always
handlewith care.
ATTENTION AU COMPOSANT AYANT
RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE
MARQUE 0 SUR LES DIAGRAMMES
SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES
COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS
DANSCE MANUEL OU DANS LES
SUPPÉMENTS PUBLIÉS PAR SONY.
[MAX]1024MB1024MB1024MB
AC adaptorPCGA-AC16V6PCGA-AC16V6PCGA-AC16V6PCGA-AC16V6PCGA-AC16V6PCGA-AC16V6PCGA-AC16V6
BatteryPCGA-BP2TPCGA-BP2TPCGA-BP2TPCGA-BP2TPCGA-BP2TPCGA-BP2TPCGA-BP2T
internal W-LAN
OSXP HomeXP HomeXP ProXP Pro, XP HomeXP ProXP HomeXP Home
[MA]
1
ULV P-M 1GHz
or M-Cel 800MHz
CD-RW/DVD-ROM
or DVD-RW
256MB × 1 or 512MB × 1
or 512MB × 2
1024MB
ULV P-M 1GHzULV P-M 1GHzULV P-M 1GHz
CD-RW/DVD-ROM
or DVD-RW
512MB × 1
or 512MB × 2
CD-RW/DVD-ROMCD-RW/DVD-ROM
512MB × 1512MB × 1
1024MB1024MB1024MB
aaaaaaa
[MA]
1
[MA]
1
[MA]
3
CPU
Graphic
LCD
HDD
OPT-DRIVE
MEMORY1
AC adaptor
Battery
internal W-LAN
OS
• The trademarks of registered trademarks of above table, refer to page 2.
• The model that is accompanied by asterisk (∗) is the CTO model.
∗1= Reference Number of the "PCG-TR3 Series" Service Manual
M/B
HDD
LCD
Memory
Battery
Opt.Drive
Internal W-LAN
Office
OS
1
[MA]
The parts marked "a" are commonly used in all models. For the component of
theparts that are not shown here, please refer to the PCG-TR3 Service Manual.