Sony PCG-K12FP, PCG-K12P, PCG-K13, PCG-K13F, PCG-K13Q Service Manual

...
PCG-GRZ530
SERVICE MANUAL
Ver 1-2002K
Revision History
For American Area
US Model
CanadianModel
S400
Confidential
• Design and specifications are subject to change without notice.
9-876-035-01
NOTEBOOK COMPUTER
Information in this document is subject to change without notice.
Sony, VAIO and CLIE are trademarks or registered trademarks of
Sony. Microsoft, Windows, Windows Media, Outlook, Bookshelf
and other Microsoft products are trademarks or registered trademarks
of Microsoft Corporation in the United States and other countries.
The word Bluetooth and the Bluetooth logo are trademarks of
Bluetooth SIG, Inc. AMD, the AMD logo, other AMD product names
and combinations thereof are trademarks of Advanced Micro
Devices, Inc. Intel Inside logo, Pentium and Celeron are trademarks
or registered trademarks of Intel Corporation. Transmeta, the
Transmeta logo, Crusoe Processor, the Crusoe logo and
combinations thereof are trademarks of Transmeta Corporation in
the USA and other countries. Graffiti, HotSync, PalmModem, and
Palm OS are resistered trademarks, and the Hotsync logo and Palm
are trademarks of Palm, Inc. or its subsidiaries. (M) and Motrola
are trademarks of Motrora, Inc. Other Motrola products and services
with (R) mark like Dragomball are the trademarks of Motrola, Inc.
All other names of systems, products and services in this manual
are trademarks or registered trademarks of their respective owners.
In this manual, the (TM) or (R) mark are not specified.
Caution Markings for Lithium/Ion Battery - The following or similar
texts shall be provided on battery pack of equipment or in both the
operating and the service instructions.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer. Discard used batteries according to the
manufacturer’s instructions.
CAUTION: The battery pack used in this device may present a fire
or chemical burn hazard if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
Dispose of used battery promptly.
Keep away from children.
CAUTION: Changing the back up battery.
• Overcharging, short circuiting, reverse charging, multilation or
incineration of the cells must be avoided to prevent one or more of
the following occurrences; release of toxic materials, release of
hydrogen and/or oxygen gas, rise in surface temperature.
• If a cell has leaked or vented, it should be replaced immediately
while avoiding to touch it without any protection.
Service and Inspection Precautions
1. Obey precautionary markings and instructions
Labels and stamps on the cabinet, chassis, and components identify areas requiring special precautions. Be sure to observe these precautions, as well as all precautions listed in the operating manual and other associated documents.
2. Use designated parts only
The set’s components possess important safety characteristics, such as noncombustibility and the ability to tolerate large voltages. Be sure that replacement parts possess the same safety characteristics as the originals. Also remember that the 0 mark, which appears in circuit diagrams and parts lists, denotes components that have particularly important safety functions; be extra sure to use only the designated components.
3. Always follow the original design when mounting parts and routing wires
The original layout includes various safety features, such as inclusion of insulating materials (tubes and tape) and the mounting of parts above the printer board. In addition, internal wiring has been routed and clamped so as to keep it away from hot or high-voltage parts. When mounting parts or routing wires, therefore, be sure to duplicate the original layout.
4. Inspect after completing service
After servicing, inspect to make sure that all screws, components, and wiring have been returned to their original condition. Also check the area around the repair location to ensure that repair work has caused no damage, and confirm safety.
5. When replacing chip components...
Never reuse components. Also remember that the negative side of tantalum capacitors is easily damaged by heat.
6. When handling flexible print boards...
• The temperature of the soldering-iron tip should be about 270C.
• Do not apply the tip more than three times to the same pattern.
• Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are easily damaged by vibration. Always handle with care.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
— 2 —
Confidential
PCG-GRZ530 (AM)

TABLE OF CONTENTS

Section Title Page
CHAPTER 1. BLOCK DIAGRAM ............................... 1-1
(to 1-2)
CHAPTER 2. FRAME HARNESS DIAGRAM ........ 2-1
(to 2-2)
CHAPTER 3. EXPLODED VIEWS AND
PARTS LIST............................................ 3-1
3-1. Main Section .................................................................... 3-2
3-2. LCD Section – Made by HI – .......................................... 3-5
3-3. Connector Section (CH Type Only)................................. 3-7
(to 3-8)
CHAPTER 4. OTHERS ................................................... 4-1
4-1. Replacing the CPU .......................................................... 4-1
1. Removing the CPU .......................................................... 4-1
2. Installing the CPU ............................................................ 4-1
(to 4-1)
History of the changes is shown as the “Revision History” at the end of this data.
— 3 —
Confidential
PCG-GRZ530 (AM)
CHAPTER 1.
BLOCK DIAGRAM
USB Ri ght
CONN
USB Left
CONN
USB Rear
CONN
MS
CONN
EEPRO M
On DIMM1
RJ 45
For SPD
Pentium 4
Processor
512KB L2
478pins
uFCPGA
USB3
USB2
Memory
Stick
Module
For SPD
EEPROM
On DIMM 2
EEPROM
For Passw ord
RJ-45
Port-0
Port-3
Port-3
Port-2 Port-2
Port-4
SMBUS2
EEPROM
For ClockG
CPU Local Bus
Port-1
Port-5
IDE(ATA100)
EN
Internal
HDD
Port0-5
Primary
Reserved
Reserved
Secondary
Chipset : Intel 845MZ
Memory
CONTROLLER
HUB (MCH)
593 FCBGA
AGP x 4
IO Control Hub
ICH3 -m
FW82801CAM
200MHz Memory Bus
(DDR1600)
DDR(SO-DIMM)
Total max memory size
512MB
Ether
PHY
EEPROM
For LAN
RJ-45
RJ-45
LPC
SMBUS 2
Re fer to Clock Gene rator
Graphics
M7CSP16
Vide o Memory
16MB
CARDBUS
& i.LINK
RICOH R5C5 52
Bus #2 Dev #5
CLKGEN
9870GTD
Block Diagram
AT I
i.LINK 0
IM I
PCI BUS(3.3V)
For i.LINK
EEPR OM
BLOCK DIAGRAM Rev. 0.60
SMBUS2
LCD CONN
TV- Out
CardBus/16b itCard
15inch XGA
SONY
Cable
TV-Out
S-Video-Ou t
PC Card
Connector
2 Slot
TV-Out
LineOut
i.LINK0
Dock -VGA DB-15
VGA DSUB-15
i.LINK
AV Out
Port Repricator
TV-Out
LineOut
S-Video-Out
Out
AV
RJ11
DC Jack
DC in
RJ-11
Multi Purpose Bay
2nd
Battery
BATTERY2
Power
Circuit
1st
Battery
Optical
Drive
BATTERY1
MDC
(Mod em
Daughter
Card)
Module
RJ-11
AC LINK
t
u
O
e
n
i
L
LINE-OUT
Audio
YMF753
(Yamaha)
H
e
a
AMP, etc.
PHONE
OUT
Dock-VGA DB-15
JOG
Controller
JOG
Parallele
SMBUS1
LID
& SM BUS MUX
SMBUS0
I/O Expander
BATTERY1
FAN0 ATF0
Other
Control
BATTERY2
Parallele
RJ-45
Serial
Parallele
PS/2
USB3
USB2
DCin
FWH
8Mb
(Flash BIOS
ROM)
S
M
I
C
MIC
IN
p
e
a
k
e
r
Speak er
L&R
d
p
h
o
n
e
Super I/O
SMsC
LPC47N227
Parallele
Internal Key Board
H8S/2149
KBC/EC
SPIC
Serial
PS/2
TouchPad
Membrane
VGA
DB-15
RJ45
Serial
Parallele
PS/2
USB
CONN
USB
CONN
DC Jack
1/1
Confidential
1-21-1
(END)
PCG-GRX530 (AM)
Loading...
+ 9 hidden pages