Page 1
SWITCHER PROCESSOR PACK
MVS8000SF-C
MULTI FORMAT SWITCHER PROCESSOR
MVS-8000SF
HK-PSU04
MKS-8110HD
MKS-8160HD
MKS-8170HD
MKS-8210HD
MKS-8440HD
MKS-8210K1
MKS-8110SD
MKS-8160SD
MKS-8170SD
MKS-8210SD
MKS-8440SD
MKS-8440K1
MKS-8110M
MKS-8160M
MKS-8170M
MKS-8210M
MKS-8440M
MKS-8420M
INSTALLATION MANUAL
1st Edition (Revised 2)
Page 2
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
MVS-8000SF Serial No. 10001 and Higher
MKS-8110HD Serial No. 10001 and Higher
MKS-8110SD Serial No. 10001 and Higher
MKS-8110M Serial No. 10001 and Higher
MKS-8160HD Serial No. 10001 and Higher
MKS-8160SD Serial No. 10001 and Higher
MKS-8160M Serial No. 10001 and Higher
MKS-8170HD Serial No. 10001 and Higher
MKS-8170SD Serial No. 10001 and Higher
MKS-8170M Serial No. 10001 and Higher
MKS-8210HD Serial No. 10001 and Higher
MKS-8210SD Serial No. 10001 and Higher
MKS-8210M Serial No. 10001 and Higher
MKS-8420M Serial No. 10001 and Higher
MKS-8440HD Serial No. 10001 and Higher
MKS-8440SD Serial No. 10001 and Higher
MKS-8440M Serial No. 10001 and Higher
MKS-8210K1 Serial No. 10001 and Higher
MKS-8440K1 Serial No. 10001 and Higher
HK-PSU04 Serial No. 10001 and Higher
MVS-8000SF
Page 3
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.
6. When performing the installation, keep the rear of
the unit 10 cm (4 inches) or more away from walls
in order to obtain proper exhaust and radiation of
heat.
When using a LAN cable:
For safety,do not connect to the connector for
peripheral device wiring that might have excessive
voltage.
MVS-8000SF
1 (P)
Page 4
Page 5
Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 3
Related manuals......................................................................................................... 3
Contents ..................................................................................................................... 3
1. Installation
1-1. Operating Environment ...............................................................................1-1
1-2. Power Supply .............................................................................................. 1-1
1-2-1. Power Specifications ..................................................................1-1
1-2-2. Recommended Power Cord ........................................................ 1-1
1-3. Installation Space (External dimensions) .................................................... 1-2
1-3-1. MVS8000SF-C ........................................................................... 1-2
1-4. Installing the Options .................................................................................. 1-3
1-4-1. Installing the Plug-in Boards ...................................................... 1-3
1-4-2. Installing the Connector Board ..................................................1-6
1-4-3. Installing the HK-PSU04 ...........................................................1-7
1-4-4. Upgrade ...................................................................................... 1-7
1-4-5. Installing the MKS-8420M ........................................................ 1-8
1-5. Rack Mounting ............................................................................................ 1-9
1-6. Matching Connectors ................................................................................ 1-11
1-7. Input/Output Signals of Connectors .......................................................... 1-12
1-8. Checks on Completion of Installation ....................................................... 1-14
1-8-1. Description of On-board Switches and LEDs ..........................1-14
1-8-2. Checks on the Switch Setting the Number of
Power Supply Units.................................................................. 1-57
1-9. System Connection.................................................................................... 1-58
MVS-8000SF
2. Service Overview
2-1. Troubleshooting .......................................................................................... 2-1
2-2. Periodic Inspection and Maintenance ......................................................... 2-2
2-2-1. Cleaning .....................................................................................2-2
2-3. About the Data Backup Capacitor ............................................................... 2-2
1
Page 6
Page 7
Purpose of this manual
Related manuals
Manual Structure
This manual is the installation manual of Switcher Processor Pack MVS8000SF-C
and their optional boards and units.
This manual is intended for use by trained system and service engineers, and
describes the information on installing the MVS8000SF-C.
The following manuals are prepared for MVS8000SF-C and their optional boards
and units.
..
. Operation Manual (Supplied with MVS8000SF-C)
..
This manual describes the application and operation of MVS8000SF-C.
..
. System Setup Manual (Available on request)
..
This manual describes the information that is required to connect the MVS-8xxx/
MVE-8000/DCU-8000/CCP-8000 to the MVS-8000 system, and to start up the
system.
If this manual is required, please contact your local Sony Sales Office/Service
Center.
Contents
..
. Maintenance Manual (Available on request)
..
This manual describes the detailed service information.
If this manual is required, please contact your local Sony Sales Office/Service
Center.
This manual is organized by following sections.
Section 1 Installation
This section describes the operating environment, power supply, installation space,
installation of optional boards and units, rack mounting, connectors, input and
output signals of connectors, checking upon completion of installation, and system
configuration.
Section 2 Service Overview
This section describes the troubleshooting and periodic inspection and maintenance.
MVS-8000SF
3
Page 8
Page 9
Section 1
For customers in the U.S.A. and Canada
1 Power cord, 125 V 10 A (2.4 m) : ! 1-557-377-11
AC inlet
1
Installation
1-1. Operating Environment
Operating guaranteed temperature : +5 dC to +40 dC
Performance guaranteed temperature : +10 dC to +35 dC
Operating humidity : 10 % to 90 %
(relative humidity)
Storage temperature : _20 dC to +60 dC
Mass : Approx. 45 kg
(when all options
are installed)
Prohibited locations for installation
. Areas where the unit will be exposed do direct sunlight
or any other strong lights.
. Dusty areas
. Areas subject to vibration.
. Areas with strong electric or magnetic fields.
. Areas near heat sources.
. Areas subject to electrical noise.
. Areas subject where is subjected to static electricity.
Ventilation
The inside of the MVS8000SF-C is cooled by a fan (on
both sides).
The power supply can be damaged if the exhaust vent (on
both sides) and air intake (front panel) are blocked or the
fan is stopped.
Therefore, leave a blank space of more than 10 cm in the
front and back of the MVS8000SF-C.
m
. As the inrush current at turn-on is a maximum 60 A (at
100 V)/110 A (at 230 V), the capacity of the AC power
source must be commensurate with this load.
If the capacity of the AC power is not adequately large,
the AC power source braker will operate or the unit will
abnormally operate.
. This system contains the two power supply units as the
standard configuration. A fourth, redundant, power
supply may be installed as an option.
When starting up this system, be sure to turn on the
power of all the power supply units.
1-2-2. Recommended Power Cord
w
. The power cord is not supplied with the MVS8000SF-C.
Be sure to use the power cord that is applicable to places
in the area.
To avoid a fire or an electric shock, be sure to use the
designated power cord.
. Do not damage the power cord otherwise a fire or
electric shock may result.
1-2. Power Supply
1-2-1. Power Specifications
A switching regulator is used for the power supply of this
unit. The voltage within the range of 100 V to 240 V can
be used without changing the supply voltage.
Power requirements : AC 100 to 240 V ± 10 %
Power frequency : 50/60 Hz
Current consumption : 100 V : 10 A, 240 V : 4.2 A
MVS-8000SF
(with all options installed)
For customers in the all European countries
1 Power cord, 250 V 10 A (2.4 m) : ! 1-782-929-21
1
AC inlet
1-1
Page 10
1-3. Installation Space (External dimensions)
1-3. Installation Space (External dimensions)
1-3-1. MVS8000SF-C
520
482
465
440
375
7
35
37.6
279.4
354(8U)
17.5
339
144.5 115.5 115.5
61
370
35
1-2
Unit : mm
MVS-8000SF
Page 11
1-4. Installing the Options
1-4. Installing the Options
The MVS8000SF-C is shipped from the factory with the
necessary option boards (refer to the following table)
already installed in accordance with the specified system
configuration.
The following options are available for the MVS-8000SF.
MVS-8000SF Option List
Model name Board Structure
Plug-in board
MKS-8110HD _ CNI-9 board
17 Input Board
MKS-8110SD _ CNI-10 board
17 Input Board
MKS-8110M _ CNI-22 board
17 Input Board
MKS-8160HD OUT-23 board CNO-11 board
8 Output Board
MKS-8160SD OUT-24 board CNO-17B board
8 Output Board
MKS-8160M OUT-27 board CNO-23 board
8 Output Board
MKS-8170HD DIF-119 board _
DME Interface Board
MKS-8170SD DIF-122 board _
DME Interface Board
MKS-8170M DIF-141 board _
DME Interface Board
MKS-8210HD DI-40 board _
Mix/Effect Board Set
MKS-8210SD DI-41 board _
Mix/Effect Board Set
MKS-8210M DI-43 board _
Mix/Effect Board Set
MKS-8420M CC-90 board _
Color Corrector Board
MKS-8440HD DIO-62 board _
Frame Memory Board Set
MKS-8440SD DIO-63 board _
Frame Memory Board Set
DO-41 board _
MIX-45 board _
KPC-16 board _
DO-42 board _
MIX-45 board _
KPC-16 board _
DO-44 board _
MIX-45 board _
KPC-16 board _
MY-102 board _
MY-102 board _
Connector board
Model name Board Structure
Plug-in board
MKS-8440M DIO-74 board _
Frame Memory Board Set
MKS-8210K1 DI-43 board _
1 M/E Upgrade Kit
MKS-8440K1 DIO-74 board _
Frame Memory Upgrade Kit
HK-PSU04 __
Power Supply Unit
MY-102 board _
DO-44 board _
Connector board
1-4-1. Installing the Plug-in Boards
Each plug-in board of the Multi Format Switcher MVS8000SF is allocated to a specific slot into which they must
be installed. Check to see that the respective plug-in boards
are installed in their respective slots.
The name of the board is shown near the eject lever at the
right-most end of each plug-in board.
The respective slot numbers to which plug-in boards that
are allocated are shown inside the front panel of the MVS8000SF. Install the respective plug-in board according to
this instruction.
n
Check to see that connectors of the plug-in boards are
securely into the MB-974 board of the MVS-8000SF
without loose contact.
If any plug-in board is inserted into the incorrect slot, it
causes a system error and the system will not work correctly.
c
Be sure to turn off the POWER switch before starting
installation work.
If installation work is started with the POWER switch left
on, it may cause electrical shock or damage to printed
circuit boards.
MVS-8000SF
1-3
Page 12
1-4. Installing the Options
Installation Procedure
1. Turn off the main power of the MVS-8000SF and
disconnect the AC power cord from the wall outlet.
2. Loosen the four screws (with drop-safe) and remove
the front panel to the arrow.
Screws
(with drop-safe)
4. While the eject levers are opened as shown in the
illustration, insert the plug-in board into the board
guide rail.
Front panel
Screws (with drop-safe)
3. Remove the six screws and remove the plug-in board
loose-proof assembly.
B3 x 5
Eject levers
Extract PWB stopper
assembly
1-4
B3 x 5
MVS-8000SF
Page 13
1
1
Eject lever Eject lever
1-4. Installing the Options
Name of option Name of board Slot on the
front side
MKS-8210HD/SD/M*1DO-41/DO-42/ 3, 8
DO-44 board
MIX-45 board 4, 9
KPC-16 board 5, 10
DI-40/DI-41/ 6, 11
DI-43 board
MKS-8170HD/SD/M DIF-119/DIF-122/ 7
DIF-141 board
MKS-8420M CC-90 board 12
MKS-8160HD/SD/M*2OUT-23/OUT-24/ 14 , 15
OUT-27 board
MKS-8440HD/SD/M DIO-62/DIO-63/ 16
DIO-74 board
MY-102 board 17
*1 : Note when installing the MKS-8210HD/8210SD/8210M
The MKS-8210HD/8210SD/8210M must be inserted into the specified
slot only for M/E. Be sure to insert it into the correct slot without fail.
The slots into which the MKS-8210HD/8210SD/8210M can be inserted
are determined in accordance with the configuration of M/Es as shown
in the following table.
Slot M/E
SLOT 3 to 6 M/E 1
SLOT 8 to 11 PGM/PST
5. While closing the eject levers in the direction of arrow
1, push in the plug-in board.
*2 : Relation between the slots in which OUT-23/OUT-24/OUT-27 boards
(MKS-8160HD/8160SD/8160M) are installed and OUTPUT is shown
below.
Slot OUTPUT
SLOT 14 1 to 8
SLOT 15 9 to 16
6. Attach the plug-in board loose-proof assembly and the
front panel by reversing the installation steps of 2, 3.
MVS-8000SF
1-5
Page 14
1-4. Installing the Options
1-4-2. Installing the Connector Board
1. Remove the two screws and remove the blank panel.
n
To install the connector board into the slot in which
the other board is installed already, loosen the two
fixing screws and remove the connector board that is
installed already.
2. Insert the connector board horizontally level and
secure it with the two fixing screws.
Fixing screw
Connector board
Blank panel
B3 x 5
n
Store the removed blank panel in a safe place.
B3 x 5
Fixing screw
Name of option Name of board Slot on the rear side
MKS-8110HD CNI-9 board IN 1 to 17
MKS-8110SD CNI-10 board 18 to 34
MKS-8110M CNI-22 board
MKS-8160HD CNO-11 board Insert into the slot on the
MKS-8160SD CNO-17B board
MKS-8160 M CNO-23 board
rear that corresponds to
the slot on the front side.
1-6
MVS-8000SF
Page 15
1-4. Installing the Options
1-4-3. Installing the HK-PSU04
The HK-PSU04 is used after it is installed in the MVS8000SF.
n
Before installing the HK-PSU04, be sure to turn off the
main power. If the HK-PSU04 is installed while the main
power is turned on, it can result in electrical shock or
damage to printed circuit boards.
Installation procedure
1. Remove the front panel of the MVS-8000SF.
(Refer to Section 1-4-1.)
2. Remove the two screws (B3 x 5) fixing the power
supply cover, and remove the power supply cover.
3. Remove the two screws (PSW3 x 6) fixing the blank
panel to the location where the HK-PSU04 is going to
be installed. Then remove the blank panel.
4. Push the portion of the HK-PSU04 marked by the
arrow and insert the HK-PSU04 into deep end as far as
it will go.
5. Secure the HK-PSU04 with the two screws removed in
step 3.
HK-PSU04
PSW3 x 6
PSW3 x 6
Blank panel
B3 x 5
PSW
3 x 6
PS cover
B3 x 5
n
Store the removed blank panel in a safe place.
6. Attach the power supply cover and the front panel by
reversing the installation steps of 1, 2.
1-4-4. Upgrade
The MVS-8000 system can be upgraded by the use of the
following upgrade kit.
Name of upgrade Name of board Slot on the
kit front side
MKS-8210K1 DO-44 board 3, 8
DI-43 board 6, 11
MKS-8440K1 DIO-74 board 16
1. When MKS-8210K1 is used
Exchange the DO-41/42 boards of the M/E unit that
you want to upgrade, with the DO-44 board of the
upgrade kit. Also, exchange the DI-40/41 boards that
you want to upgrade, with the DI-43 board of the
upgrade kit.
MVS-8000SF
2. When MKS-8440K1 is used
Exchange the DIO-62/63 boards in the slot 16 with the
DIO-74 board of the upgrade kit.
1-7
Page 16
1-4. Installing the Options
1-4-5. Installing the MKS-8420M
MKS-8420M consists of the following boards.
. CC-90 board : 1 piece
. CPU-DK module : 3 pieces
CC-90 board installation
Refer to “1-4-1. Installing the Plug-in Boards”.
CPU-DK module installation
Replace a CPU-DK module on the following boards with
each CPU-DK module of MKS-8420M.
Replacement procedure of the CPU-DK module is described as follows using the OUT-23 board as an example.
Other boards (DIF-119, DIF-122, DIF-141, OUT-24,
OUT-27, XPT-21) can also be replaced in the same way.
Front side slot No. Board name (The installed boards are
7 DIF-119 or DIF-122 or DIF-141
13 XPT-21
14 OUT-23 or OUT-24 or OUT-27
(*1) : MKS-8170HD, MKS-8170SD, MKS-8170M
Depending on the system configuration, above DME Interface Board
is not installed in slot 7.
different depending on the system
configuration.)
(*1)
c
Be sure to turn off the POWER switch before starting
installation work.
If installation work is started with the POWER switch left
on, it may cause electrical shock or damage to printed
circuit boards.
Removal
1. Remove the OUT-23 board from the MVS-8000SF.
2. Remove the two screws and washers. Remove the
bracket (K).
3. Remove the CPU-DK module from the connector of
the board.
4. Peel off the heat conduction sheet 1 (SDI) from the
removed CPU-DK module.
n
The heat conduction sheet 1 (SDI) will be reused.
Installation
1. Attach the heat conduction sheet 1 (SDI) that is
removed in step 4 of removal procedure to the new
CPU-DK module.
2. Insert the CPU-DK module connector (PN1) to the
connector (CN1501) on the OUT-23 board.
n
Confirm that the connector is securely inserted to its
root.
Bracket (K)
Heat conduction
sheet 1 (SDI)
CPU-DK
module
PN1
B3 x 6
W3,
MIDDLE
CN1501
3. Install the OUT-23 board by reversing the steps of
removal.
The illustration shows the OUT-23 board.
1-8
MVS-8000SF
Page 17
1-5. Rack Mounting
1-5. Rack Mounting
The MVS-8000SF is mounted in the 19-inch standard rack.
To mount the MVS-8000SF in the rack, use the specified
rack mount kit and follow the procedure described below.
Specified rack mount kit : RMM-10
n
If other than the specified rack mount kit is used, the unit
may not be mounted in the 19-inch standard rack.
Parts of the RMM-10
. Rack tool 2 pcs
. Right rack mount adapter 1 pc
. Left rack mount adapter 1 pc
. Rack tool attaching screw 6 pcs
(B4 x 6 : 7-682-560-09)
. Rack tool attaching screw 6 pcs
(B4 x 10 : 7-682-560-10)
Other required parts
To mount in the rack, the rack mount kit RMM-10 and the
following part are required.
. Screw for rack mounting 4 pcs
(B5 x 12 : 7-682-576-04)
2. Rack Mounting Procedure
This section describes the rack mounting procedure using
the RMM-10 rack mount kit.
n
Tighten the screws to the following torque.
Tightening torque : 120 x 10_2 N.m {12.2 kgf.cm}
1. Attach the rack tool to the side of the equipment using
the specified six screws.
n
Use B4 x 6 screws.
B4 x 6
Rack tool
1. Precautions for Rack Mounting
w
. To prevent the rack from falling or moving, fix the rack
on a flat and steady floor using bolt or others.
If the rack falls due to the weight of the equipment, it
may cause death or injury.
. Be sure to use the specified rack mount kit.
If not, injury may result and the equipment may fall due
to insufficient strength.
. After rack mounting, be sure to tighten the screws on the
rack angle and fix the unit in the rack.
If the screws on the rack angle are not tightened, the unit
may slip from the rack and fall, causing injury.
c
When mounting the unit in the rack, note the following:
. Be sure to mount in the rack with two persons or more.
. Be careful not to catch your fingers or hands in the rack
mount rail or others.
. Mount in the rack in a stable position.
n
If several units are mounted in a rack, it is recommended to
install a ventilation fan to prevent temperature rise inside
the rack.
Rack tool
B4 x 6
MVS-8000SF
1-9
Page 18
1-5. Rack Mounting
2. Loosen the screws on the rear of the right and left
adapters and adjust the length of the adapter according
to the depth of the rack.
(The illustration below shows the left adapter.)
Adapter
Portion of
the rail
B4 x 6
B4 x 6
n
Maximum depth of adapter : 750 mm
Minimum depth of adapter : 595 mm
3. Attach the right and left adapters to the rack completely using the specified six screws.
(The illustration below shows the left adapter.)
6. Align the groove of the rack tool at the side of the
equipment with the rail, and slide the equipment to the
rear.
n
The rack tools are hooked on the rails as shown below.
Rack tool
Rail Rail
Rack tool
7. Fix the rack angle in the rack using the specified
screws.
8U
B4 x 10
4U
1U
31.75
31.75
B4 x 10
Unit : mm
4. Tighten the screws (B4 x 6 : two screws each on the
right and left) for adjusting the length of the adapter
completely (the screws that were loosened in step 2).
5. Remove the front panel of the equipment.
(Refer to Section 1-4-1.)
1-10
B5 x 12
B5 x 12
8. Attach the front panel to the equipment.
(Refer to Section 1-4-1.)
MVS-8000SF
Page 19
1-6. Matching Connectors
Use the following connectors, cables or equivalents when connecting cables to the unit.
Model name Panel indication Connector name Matching connector and cable
Name Sony part No.
MKS-8110SD/HD/M PRIMARY INPUTS BNC, 75 Z Belden 8281 coaxial _
MKS-8160SD/HD/M OUTPUTS 1 to 8
MVS-8000SF REF IN BNC, 75 Z Belden 8281 coaxial _
*1 : The following crimp contact is required for the plug.
AWG#18 to #22 : 1-566-493-21
AWG#22 to #24 : 1-564-774-11
AWG#24 to #30 : 1-564-775-11
*2 : Conforms to the IEEE 802.3 Ethernet 100BASE-TX standards.
1 to 17 cable (SDTV system)
or
Belden 1694 coaxial
cable (HDTV system)
REF OUT
cable
EXT
REMOTE 1 to 4 D-sub 9-pin, Female D-sub 9-pin, Male
TERMINAL Connector 9-pin, Male 1-560-651-00
Junction Shell 9-pin 1-561-749-00
GPI D-sub 25-pin, Female D-sub 25-pin, Male
Connector 25-pin, Male 1-560-904-11
Junction Shell 25-pin 1-563-377-11
DATA RJ-45 modular jack
*2
__
CTRL
DME 1A, 1B, 2A, 2B MDR 68-pin, Female Dedicated cable _
(supplied with the
MVE-8000)
1-6. Matching Connectors
*1
*1
MVS-8000SF
1-11
Page 20
1-7. Input/Output Signals of Connectors
1-7. Input/Output Signals of Connectors
The input/output signals of the connectors at the rear panel
are as follows.
TERMINAL : RS-232C (D-sub 9-pin, Female)
to Terminal
5
_ EXT VIEW _
Pin No. Signal Name Function
1 DCD Data Carrier detect
2 RXD Received data
3 TXD Transmitted data
4 DTR Data terminal ready
5 GND Ground
6 DSR Data set ready
7 RTS Request to send
8 CTS Clear to send
9 __
(*1) :Pins 1, 4 and 6 are internally connected together on the CN-2133
board.
(*2) :Pins 7 and 8 are internally connected together on the CN-2133 board.
GPI : (D-sub 25-pin, Female)
INPUT x 8, TTL
OUTPUT x 4, relay contacts 30 V 0.1 A
(resistive load)
OUTPUT x 4, open collector, 30 V rated voltage
13
25
1
69
(*1)
(*1)
(*1)
(*2)
(*2)
1
14
Pin No. Signal Name Function
11 GPI OUT 6 General-purpose relay
12 GPI OUT 8
output (B)
(*4)
13 GPI OUT COM Ground for open collector
output
14 GND Ground
15 GPI IN 1 General-purpose input
16 GPI IN 3
17 GPI IN 5
18 GPI IN 7
19 GPI OUT 1A General-purpose relay
20 GPI OUT 2A
output (A)
(*3)
21 GPI OUT 3A
22 GPI OUT 4A
23 GPI OUT 5 General-purpose open
24 GPI OUT 7
collector output
(*4)
25 GPI OUT COM Ground for open collector
output
n
A and B of the same number constitute a pair of relay
contacts.
<Relay>
(*3)
GPI OUT x B
GPI OUT x A
x : 1-4
(*4)
<Open collector output>
GPI OUT 5-8
GPI OUT COM
+V
EXT VIEW
Pin No. Signal Name Function
1 GND Ground
2 GND Ground
3 GPI IN 2 General-purpose input
4 GPI IN 4
5 GPI IN 6
6 GPI IN 8
7 GPI OUT 1B General-purpose open
8 GPI OUT 2B
collector output (B)
9 GPI OUT 3B
10 GPI OUT 4B
1-12
(*3)
MVS-8000SF
Page 21
REMOTE 1 to 4 : RS-422A (D-sub 9-pin, Female)
<DEVICE> (*5) from External Devices
1-7. Input/Output Signals of Connectors
5
1
69
_ EXT VIEW _
Pin No. Signal Name Function
1 FG Frame ground
2TX_ Transmitted data (_)
3RX+ Received data (+)
4 GND Common ground
5 _ No Connection
6 GND Common ground
7TX+ Transmitted data (+)
8RX_ Received data (_)
9 _ No Connection
(*5) <DEVICE> : Controlling equipment
DATA/CTRL : 100BASE-TX, RJ-45 (8-pin)
1
8
_ EXT VIEW _
Pin No. Signal Name Function
1TX+ Transmitted data (+)
2TX_ Transmitted data (_)
3RX+ Received data (+)
4 _ No Connection
5 _ No Connection
6RX_ Received data (_)
7 _ No Connection
8 _ No Connection
MVS-8000SF
1-13
Page 22
1-8. Checks on Completion of Installation
1-8. Checks on Completion of Installation
1-8-1. Description of On-board Switches and LEDs
n
The number shown in the parentheses ( ) indicated the address on the circuit board.
1. CA-44 board (MVS-8000SF)
AB C D E
D1003
D1002
D1013
D901
D902
D1032
D1033
ND101
ND102
ND501
ND502
ND701
ND702
S104
S502
S702
CN103
CN503
CN703
1
2
3
4
5
E4
E5
TP1002
TP1003
TP1001
CN1003
CN1002
S302
S301
D309
D310
D601
D602
D801
D802
S102
S103
S101
S501
S701
D101
D102
D103
D104
D501
D502
D503
D504
D701
D702
D703
D704
D12
SW1
SW2
D10
D13
A
D18
D19
D14
D15
D16
D17
TP101
TP102
TP103
TP104
TP501
TP502
TP503
TP504
TP701
TP702
TP703
TP704
B
CPU-DR
Module
(MAIN CPU)
S303
G
F
E
D
C
654321
E3
D1
IF-844
(S-BUS)
TP2
S1E1
12345
F
E
D
C
CPU-DK
B
Module
A
(COM CPU-1)
12345
F
E
D
C
CPU-DK
B
Module
A
(COM CPU-2)
AB
1
A
TP1
D100
2
D101
D200
B
3
DI2
DI3
DI2
DI3
12
DI6
DI6
DI7
SW2
DI7
SW2
DI8
SW1
DI8
SW1
DI4
DI1
DI4
DI1
TP1031
SG-272
E2
E1
A side/Component side
<LED>
D101, D102, D103, D104 (A-4), ND101, ND102 (A-3) :
MAIN CPU status LED
Main CPU status indication.
D309 (A-2) : RESET status LED
System reset status indication.
Lit when S301 is pressed or the power voltage drops to
+3.3 V.
D310 (A-2) : CPU RESET status LED
CA-44 board reset status indication.
Lit when S302 is pressed or the power voltage drops to
+3.3 V.
D501 (A-4), D502, D503, D504 (A-5) : COM CPU-1
status LED
COM CPU-1 status indication.
1-14
D601 (A-2) : COM1 ACT status LED
COM CPU-1 Ethernet communication status indication.
Lit while data send or receive is in progress.
D602 (A-2) : COM1 100 status LED
COM CPU-1 Ethernet communication speed status
indication.
Lit : 100 Mb/s
Not lit : 10 Mb/s
D701, D702 (A-4), D703, D704 (A-5) : COM CPU-2
status LED
COM CPU-2 status indication.
D801 (A-2) : COM2 ACT status LED
COM CPU-2 Ethernet communication status indication.
Lit while data send or receive is in progress.
MVS-8000SF
Page 23
1-8. Checks on Completion of Installation
D802 (A-2) : COM2 100 status LED
COM CPU-2 Ethernet communication speed status
indication.
Lit : 100 Mb/s
Not lit : 10 Mb/s
D901 (A-2) : REF EXT status LED
REF IN signal presence/absence status indication.
Lit when the REF signal is input to the REF IN connector.
Not lit when the REF signal is not input to the REF IN
connector.
D902 (A-2) : PLL LOCK status LED
REF IN signal format status indication.
Lit when the REF IN signal matches with the switcher
format setup.
D1002 (A-2) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D1003 (A-1) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
D1013 (A-2) :
++
+5 V
++
+5 V power supply status indication.
Lit when the +5 V power is supplied.
D1032 (A-2) : SBUS TX status LED
S-BUS send status indication.
Lit while the data send is in progress.
D1033 (A-2) : SBUS RX status LED
S-BUS receive status indication.
Lit while the data receive is in progress.
ND501, ND502 (A-4) : COM CPU-1 status LED
COM CPU-1 status indication.
ND701, ND702 (A-4) : COM CPU-2 status LED
COM CPU-2 status indication.
<Switch>
S101 (A-3) : Mode setting switch for the main CPU
Sets the modes of the main CPU.
Default setting when shipped from the factory is all OFF.
S102 (A-2) : Group ID setting switch for LAN
Sets the group ID for connecting LAN.
For details, refer to “System Setup Manual”.
S103 (A-2) : Unit ID setting switch for LAN
Sets the unit ID for connecting LAN.
For details, refer to “System Setup Manual”.
S104 (A-4) : Monitor reset switch for the main
CPU
Pressing this switch resets the system while maintaining
this unit through the main CPU control terminal connector.
S301 (A-1) : System reset switch
Pressing this switch activates the system reset and the
system re-starts.
S302 (A-1) : CA-CPU reset switch
Pressing this switch resets the CA-44 board.
S303 (B-1) : Switch setting the number of the
power supply units
Sets the number of the power supply units that are required
for this unit.
Default setup when shipped from the factory is bits 1, 2 and
4 :
OFF, and bits 3 : ON.
S501 (A-4) : Modes setting switch for the COM CPU-1
Sets the modes of the COM CPU-1.
Default setting when shipped from the factory is all OFF.
S502 (A-4) : Monitor reset switch for the COM CPU-1
Pressing this switch resets the system while maintaining
this unit through the COM CPU-1 control terminal.
S701 (A-4) : Modes setting switch for the COM
CPU-2
Default setting when shipped from the factory is all OFF.
S702 (A-4) : Monitor reset switch for the COM CPU-2
Pressing this switch resets the system while maintaining
this unit through the COM CPU-2 control terminal.
<Connector>
CN103 (A-4) : TERMINAL pin
This pin is connected to the main CPU control terminal
and used during maintenance.
Conforms to RS-232C.
MVS-8000SF
1-15
Page 24
1-8. Checks on Completion of Installation
CN503 (A-5) : TERMINAL pin
This pin is connected to the COM CPU-1 control terminal
and used during maintenance.
Conforms to RS-232C.
CN703 (A-5) : TERMINAL pin
This pin is connected to the COM CPU-2 control terminal
and used during maintenance.
Conforms to RS-232C.
CN1003 (A-3) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
CN1002 (A-5) : TERMINAL pin
This pin is connected to the S-BUS CPU control terminal
and used during maintenance.
Conforms to RS-232C.
<TEST terminal>
E1 (E-5), E2 (E-1), E3 (C-3), E4 (A-5), E5 (A-1) :
GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
TP101, TP102, TP103, TP104 (A-4) : Main CPU
status check terminal
Main CPU status check terminal.
<LED on the CPU DR module> : Main CPU
D10 (green) (A-1) : RUN status LED
RUN status indication.
Lit when the CPU-DR module starts operating.
D12 (green) (A-4) : CD (Card Detect) status LED
Lit when the CPU-DR module is inserted correctly into the
parent board.
D13 (green) (A-1) :
++
+2.5 V
++
Indicates the statue of the +2.5 V power that is generated
by the VCC (CORE) and supplied to the CPU-DR module.
Lit while the specified power is turned on.
D14, D15, D16, D17 (A-3) (green) : STATUS1 to
STATUS4 status LED
Used for maintenance purpose. Only the STATUS1 LED is
lit in normal operation.
D18 (green) (A-4) :
++
+3.3 V
++
Indicates the statue of the VCC (I/O) power that is supplied to the CPU-DR module.
Lit while the specified power is turned on.
D19 (green) (A-4) : CORE status LED
Indicates the statue of the VCC (CORE) power that is
supplied to the CPU-DR module.
Lit while the specified power is turned on.
TP501 (A-4), TP502, TP503, TP504 (A-5) : COM
CPU-1 status check terminal
COM CPU-1 status check terminal.
TP701, TP702, TP703, TP704 (A-5) : COM CPU-2
status check terminal
COM CPU-2 status check terminal.
TP1001 (A-1) :
++
+3.3 V check terminal
++
+3.3 V measuring terminal.
TP1002 (A-1) :
++
+12 V check terminal
++
+12 V measuring terminal.
TP1003 (A-1) :
++
+5 V check terminal
++
+5 V measuring terminal.
TP1031 (D-4) : SBUS RX check terminal
S-BUS communication line measuring terminal.
<Switch on the CPU DR module> : Main CPU
SW1 (A-1) : RESET switch
Pressing this switch resets the CPU-DR module.
n
In some machines in which the CPU-DR module is
installed, the system reset may be activated.
SW2 (A-2) : MODE switch
8-pin DIP switch
Used only for production in the assembly factory. All
switches are set to OFF for normal operation.
<LED on the CPU DK module> : COM CPU-1
: COM CPU-2
DI1 (green) (B-5) : CD (Card Detect) status LED
Lit when the CPU-DK module is inserted correctly to the
parent board.
DI2 (green) (F-3) : RUN status LED
Lit when the CPU-DK module starts operating.
1-16
MVS-8000SF
Page 25
1-8. Checks on Completion of Installation
DI3 (F-3), DI6 (F-3), DI7 (F-3), DI8 (F-4) (green) :
STATUS1 to STATUS4 LED
Used for maintenance purpose. Only the STATUS1 LED is
lit in normal operation.
DI4 (green) (B-5) :
++
+3.3 V
++
Indicates the status of the VCC (CORE) and VCC (I/O)
powers that are supplied to the CPU-DK module.
<Switch on the CPU DK module> : COM CPU-1
: COM CPU-2
SW1 (D-5) : RESET switch
Pressing this switch resets the CPU-DK module.
n
In some machines in which the CPU-DK module is
installed, the system reset may be activated.
SW2 (C-5) : MODE switch
8-pin DIP switch
Used only for production in the assembly factory. All
switches are set to OFF for normal operation.
Default setting when shipped from the factory is all OFF.
<LED on the SG-272 board>
D100 (B-1) : REF OK status LED
Lit while V sync of the reference input is detected.
D101 (B-1) : REF EXT status LED
Lit while sync signal is input to the reference input.
D200 (B-1) : LOCK status LED
Lit while the machine is locked to the reference signal.
<LED on the IF-844 board> : S-BUS
D1 (B-1) : SBUS RX status LED
Lit when receiving data.
<Switch on the IF-844 board> : S-BUS
S1 (B-3) : RESET switch
Pressing this switch resets the IF-844 board.
<TEST terminal on the IF-844 board>
E1 (B-3) : GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
TP1 (A-2) : RX check terminal
S-BUS communication line measuring terminal.
TP2 (A-3) : TEST terminal
Terminal for testing.
MVS-8000SF
1-17
Page 26
1-8. Checks on Completion of Installation
2. DO-41 board (MKS-8210HD)/DO-42 board (MKS-8210SD)/DO-44 board (MKS-8210M)
AB C DE F GH J K L MN P R
1
2
3
D1
TP2
D5
4
TP10
D6
TP1
D7
5
TP3
D9
D8
6
CN1
E1
E2
TP4500TP6000
TP4
TP4501TP6001
TP4000
TP4001
TP4002TP4502TP6002
E3
7
S1
8
E8
9
TP1002
TP1001
TP1000
TP1502
TP1501
TP1500 TP2000 TP2500 TP3000 TP3500
E4
TP2002
TP2001
TP2502
TP2501
E5
TP3002
TP3001
TP3502
TP3501
E7
10
11
12
TP5
13
TP6
TP7
E6
TP8
TP9
DO-41 board A side/Component side
1-18
MVS-8000SF
Page 27
1-8. Checks on Completion of Installation
AB C DE F GH J K L MN P R
1
2
E6
3
D1
TP2
D6
4
TP1
D7
TP3
5
D9
D8
6
CN1
7
TP6002
TP6001
E2
TP4
TP4002
TP4500TP6000
TP4001
E1
TP4000
E3
S1
8
9
10
11
12
13
..
. DO-41/42 board
..
TP1000
TP1001
E4
TP1500 TP2000 TP2500 TP3000 TP3500
TP1501
TP1502
TP2001
TP1002
<LED>
D1 (A-3) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
E5
TP2002
TP8
E7
TP9
TP2501
TP5
TP2502
TP3001
TP3002
TP3501
TP6
TP3502
TP7
DO-42 board A side/Component side
D8 (A-6) : CONF2 status LED
D10 to L10 FPGA (Spartan II) CONFIG DONE status
indication.
Not lit when configuration is completed.
D5 (A-4) :
++
+5 V (DO-41 board)
++
+5 V power supply status indication.
Lit when the +5 V power is supplied.
D6 (A-4) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D7 (A-5) :
++
+2.5 V
++
+2.5 V power supply status indication.
Lit when the +2.5 V power is supplied.
MVS-8000SF
D9 (A-5) : CONF1 status LED
H2 to L2 FPGA (Spartan II) CONFIG DONE status
indication.
Not lit when configuration is completed.
<Switch>
S1 (A-8) : Reset switch
Pressing this switch initializes the DO-41/42 board.
<Connector>
CN1 (A-6) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
1-19
Page 28
1-8. Checks on Completion of Installation
<TEST terminal>
E1 (F-6), E2 (J-4), E3 (L-6), E4 (E-9), E5 (J-9), E-6 (M-12),
E-7 (N-9), E-8 (A-9) : GND terminal (DO-41 board)
Use this terminal as the earth point for measuring the
respective check terminals.
E1 (M-4), E2 (G-4), E3 (L-6), E4 (E-8), E5 (G-8), E6 (A-2),
E7 (N-9) :
GND terminal (DO-42 board)
Use this terminal as the earth point for measuring the
respective check terminals.
TP1 (A-4) :
++
+3.3 V check terminal
++
+3.3 V measuring terminal.
TP2 (A-4) :
++
+12 V check terminal
++
+12 V measuring terminal.
TP3 (A-5) :
++
+2.5 V check terminal
++
+2.5 V measuring terminal.
TP4 (H-6), TP5 (H-13) : CK (clock for video signal)
signal check terminal
Used when checking the clock for video signal.
TP1000 (E-9), TP1500 (F-9), TP2000 (G-9), TP2500
(J-9), TP3000 (K-9), TP3500 (M-9), TP4000 (K-4),
TP4500 (J-4), TP6000 (H-4) : PLL LOCK signal
check terminal (DO-41 board)
PLL-LOCK signal measuring terminal.
TP1001 (C-10), TP1501 (E-10), TP2001 (F-10),
TP2501 (H-10), TP3001 (J-10), TP3501 (K-10),
TP4001 (M-3), TP4501 (K-3), TP6001 (J-3) : EAV_C
signal check terminal (DO-41 board)
EAV_C signal measuring terminal.
TP1001 (D-10), TP1501 (F-10), TP2001 (G-10),
TP2501 (H-10), TP3001 (K-9), TP3501 (L-9), TP4001 (L-3),
TP4501 (J-3), TP6001 (H-3) : EAV_C signal check
terminal (DO-42 board)
EAV_C signal measuring terminal.
TP1002 (C-9), TP1502 (E-9), TP2002 (F-9), TP2502 (H-9),
TP3002 (J-9), TP3502 (K-9), TP4002 (M-3), TP4502 (K-3),
TP6002 (J-3) : EAV_Y signal check terminal (DO41 board)
EAV_Y signal measuring terminal.
TP6 (L-13) : VD (vertical sync) signal check
terminal
Used when checking the VD signal supplied from the
mother board.
TP7 (L-13) : CKX (control timing) signal check
terminal
Used when checking the CKX signal supplied from the
mother board.
TP8 (M-13) : HD (horizontal sync) signal check
terminal
Used when checking the HD signal supplied from the
mother board.
TP9 (M-13) : FLOE (field odd even) signal check
terminal
Used when checking the FLOE signal supplied from the
mother board.
TP10 (A-4) :
++
+5 V check terminal (DO-41 board)
++
+5 V measuring terminal.
TP1002 (D-10), TP1502 (F-10), TP2002 (G-10),
TP2502 (J-10), TP3002 (K-9), TP3502 (L-9), TP4002 (L-3),
TP4501 (J-3), TP6002 (H-3) : EAV_Y signal check
terminal (DO-42 board)
EAV_Y signal measuring terminal.
TP1000 (D-8), TP1500 (E-8), TP2000 (F-8), TP2500 (H-8),
TP3000 (J-8), TP3500 (L-8), TP4000 (L-4), TP4500 (K-4),
TP6000 (H-4) : VCO-FRQ signal check terminal
VCO-FRQ signal measuring terminal.
1-20
MVS-8000SF
Page 29
1-8. Checks on Completion of Installation
AB C DE F GH J K L MN P R
1
2
D1
3
TP1
D9504
4
5
6
7
TP9501
D9004
TP9001
D5
E8
E2
E1
TP4
E3
S2
8
CN1
S1
9
10
11
12
13
..
. DO-44 board
..
E4 E5
<LED>
D1 (A-3) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
D5 (A-4) : CONF ERR status LED
FPGA (EP20K100E) CONFIG DONE status indication.
Not lit when all configurations are completed.
D9004 (A-4) :
++
+1.8 V
++
+1.8 V power supply status indication.
Lit when the +1.8 V power is supplied.
E7
E6
TP5
TP8
DO-44 board A side/Component side
TP9
<Switch>
S1 (A-9) : Reset switch
Pressing this switch initializes the DO-44 board.
S2 (A-8) : JTAG switch
Used only for production in the assembly factory. Set this
switch to ON only when writing program in the JTAG
device with ISP.
<Connector>
CN1 (A-8) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
D9504 (A-3) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
MVS-8000SF
<TEST terminal>
E1 (G-6), E2 (G-4), E3 (L-6), E4 (D-8), E5 (J-8), E-6 (M-12),
E-7 (N-9), E-8 (A-5) : GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
1-21
Page 30
1-8. Checks on Completion of Installation
TP1 (A-3) :
++
+12 V check terminal
++
+12 V measuring terminal.
TP4 (H-6), TP5 (H-13), TP9 (N-13) : CK (clock for
video signal) signal check terminal
Used when checking the clock for video signal.
TP8 (M-13) : HD (horizontal sync) signal check
terminal
Used when checking the HD signal supplied from the
mother board.
TP9001 (A-4) :
++
+1.8 V check terminal
++
+1.8 V measuring terminal.
TP9501 (A-4) :
++
+3.3 V check terminal
++
+3.3 V measuring terminal.
1-22
MVS-8000SF
Page 31
3. MIX-45 board (MKS-8210HD/SD/M)
AB C DE F GH J K L MN P R
1
2
3
S1701
D3704
4
TP3700
D3702
TP3723
D3701
TP3717
D3700
5
TP3702
6
1-8. Checks on Completion of Installation
TP3605
TP3610
TP3606
7
E3719
S1702
D1
D2
D2201
D2202
D2206
8
9
10
11
12
13
CN1703
D2203
D2204
D2205
D12
SW2
SW1
D10
D13
D18
D19
D14
D15
D16
D17
A
TP1702
C
B
CPU-DR
Module
D
654321
G
F
E
<LED>
D1 (A-9) : MIXER (Y) status LED
MIXER (Y) CONFIG DONE status indication.
Not lit when configuration is completed.
TP3611
TP1801
TP3607
TP3604
TP3602
TP3603
TP3601
A side/Component side
D2202 (A-10) : TBC-B system status LED
TBC-B system CONFIG DONE status indication.
Not lit when configuration is completed.
D2 (A-9) : MIXER (C) status LED
MIXER (C) CONFIG DONE status indication.
Not lit when configuration is completed.
D2201 (A-9) : TBC-A system status LED
TBC-A system CONFIG DONE status indication.
Not lit when configuration is completed.
MVS-8000SF
D2203, D2204, D2205 (A-8) : MIX-CPU status LED
Indicates the CPU status on the MIX board.
D2206 (A-10) : P-XPT status LED
PXPT CONFIG DONE status indication.
Not lit when configuration is completed.
D3700 (A-5) :
++
+1.8 V
++
+1.8 V power supply status indication.
Lit when the +1.8 V power is supplied.
1-23
Page 32
1-8. Checks on Completion of Installation
D3701 (A-5) :
++
+2.5 V
++
+2.5 V power supply status indication.
Lit when the +2.5 V power is supplied.
D3702 (A-4) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D3704 (A-4) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light on, the fuse may have blown.
<Switch>
S1701 (A-4) : MIX-CPU reset switch
Pressing this switch initializes the CPU on the MIX-45 board.
S1702 (A-8) : Monitor reset switch
The reset switch that is used to reset the monitor during
maintenance through the terminal.
<Connector>
CN1703 (A-8) : TERMINAL pin
TERMINAL pin
This pin is connected to the control terminal and used
during maintenance.
Conforms to RS-232C.
TP3603 (N-12) : CKX (control timing) signal check terminal
Use this terminal to check the CKX signal supplied from
mother board.
TP3604 (N-12) : VD (vertical sync) signal check terminal
Use this terminal to check the VD signal supplied from
mother board.
TP3605 (N-5) : Buffered VD0 (vertical sync) signal
check terminal
Use this terminal to check the VD signal that is used on
this board.
TP3606 (P-6) : Buffered CKX0 (switching) signal
check terminal
Use this terminal to check the CKX signal that is used in
this circuit board.
TP3607 (N-12) : CK (clock for video) signal check
terminal
Use this terminal to check the clock for video signal that is
used in this circuit board.
TP3610 (N-6) : Buffered HD0 (horizontal sync)
signal check terminal
Use this terminal to check the HD signal that is used in this
circuit board
CN2201 (A-6) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
TP3611 (N-7) : Buffered FLOE0 (field odd even)
signal check terminal
Use this terminal to check the FLOE signal that is used in
this circuit board.
<TEST terminal>
E3719 (A-7) : GND terminal
Use this terminal as the earth point for measuring the
TP3700 (A-4) :
+12 V measuring terminal.
respective check terminals.
TP3702 (A-5) :
TP1702 (B-8) : CPU CK (CPU clock) signal check terminal
+1.8 V measuring terminal.
Use this terminal to check the CPU clock for video signal.
TP3717 (A-5) :
TP1801 (K-7) : DLY_WE terminal
+2.5 V measuring terminal.
Use this terminal to check the Write_Enable signal of the
delay circuit.
TP3723 (A-4) :
+3.3 V measuring terminal.
TP3601 (N-13) : FLOE (field odd even) signal
check terminal
Use this terminal to check the FLOE signal from the
mother board.
TP3602 (N-13) : HD (horizontal sync) signal check terminal
Use this terminal to check the HD signal supplied from
mother board.
<LED on the CPU DR module> (C11)
Refer to < LED on the CPU DR module > in “1. CA-44
board”.
<Switch on the CPU DR module> (C11)
Refer to < Switch on the CPU DR module > in “1. CA-44
board”.
++
+12 V check terminal
++
++
+1.8 V check terminal
++
++
+2.5 V check terminal
++
++
+3.3 V check terminal
++
1-24
MVS-8000SF
Page 33
4. KPC-16 board (MKS-8210HD/SD/M)
1-8. Checks on Completion of Installation
AB C DE F GH J K L MN P R
1
2
3
4
5
6
7
8
9
10
11
TP6060
TP6061
D6001
D6065
D6060
D6062
D6063
D6061
CN6000
D6108
D6107
D6106
D6105
D6104
D6103
D6102
D6101
D6100
D6109
TP6802
E6069 TP6068
TP6067
E6066
E6065
TP6801
E6064
E6063
TP6000
12
13
<LED>
D6001 (A-5) : RESET status LED
System reset status indication.
Lit when the +3.3 V power decreases.
D6060 (A-5) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D6061 (A-6), D6062 (A-5), D6063 (A-5) :
++
+1.8 V
++
+1.8 V power supply status indication.
Lit when the +1.8 V power is supplied.
D6065 (A-5) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
E6062
TP6800
TP6104
TP6103
TP6102
TP6101
A side/Component side
D6100 (A-10) : COMMON WASH FPGA CONFIG
DONE status LED
COMMON WASH FPGA CONFIG DONE status indication.
Not lit when configuration is completed.
D6101 (A-10) : WASH4 FPGA CONFIG DONE
status LED
WASH4 FPGA CONFIG DONE status indication.
Not lit when configuration is completed.
D6102 (A-10) : WASH3 FPGA CONFIG DONE
status LED
WASH3 FPGA CONFIG DONE status indication.
Not lit when configuration is completed.
MVS-8000SF
1-25
Page 34
1-8. Checks on Completion of Installation
D6103 (A-10) : WASH2 FPGA CONFIG DONE
status LED
WASH2 FPGA CONFIG DONE status indication.
Not lit when configuration is completed.
D6104 (A-9) : WASH1 FPGA CONFIG DONE status
LED
WASH1 FPGA CONFIG DONE status indication.
Not lit when configuration is completed.
D6105 (A-9) : KEYER4 FPGA CONFIG DONE
status LED
KEYER4 FPGA CONFIG DONE status indication.
Not lit when configuration is completed.
D6106 (A-9) : KEYER3 FPGA CONFIG DONE
status LED
KEYER3 FPGA CONFIG DONE status indication.
Not lit when configuration is completed.
D6107 (A-9) : KEYER2 FPGA CONFIG DONE
status LED
KEYER2 FPGA CONFIG DONE status indication.
Not lit when configuration is completed.
D6108 (A-9) : KEYER1 FPGA CONFIG DONE
status LED
KEYER1 FPGA CONFIG DONE status indication.
Not lit when configuration is completed.
D6109 (A-10) : WKG FPGA CONFIG DONE status
LED
WKG FPGA CONFIG DONE status indication.
Not lit when configuration is completed.
TP6060 (A-2) :
++
+3.3 V check terminal
++
+3.3 V measuring terminal.
TP6061 (A-4), TP6067 (G-1), TP6068 (F-4) :
++
+1.8 V
++
check terminal
+1.8 V measuring terminal.
TP6101 (N-13) : VD (vertical sync) signal check
terminal
Used to check the VD signal supplied from the mother
board.
TP6102 (N-13) : CKX (control timing) signal check
terminal
Used to check the CKX signal supplied from the mother
board.
TP6103 (N-13) : HD (horizontal sync) signal check
terminal
Used to check the HD signal supplied from the mother
board.
TP6104 (N-12) : FLOE (field odd even) signal
check terminal
Used to check the FLOE signal supplied from the mother
board.
TP6800 (N-13) : HALF VIDEO CLOCK signal check
terminal
Used to check the HALF VIDEO CLOCK signal.
TP6801 (N-10) : VCLK (clock for video signal)
signal check terminal
Used to check the clock for video signal
<Connector>
CN6000 (A-6) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
<TEST terminal>
E6062 (N-12), E6063 (N-7), E6064 (N-1), E6065 (K-
10), E6066 (K-4), E6069 (E-4), : GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
TP6000 (P-8) : SYS_CLK signal check terminal
Used for checking the SYSTEM CLOCK signal.
1-26
TP6802 (A-11) : DLY_WE terminal
Used to check the Write-Enable signal of the delay circuit.
MVS-8000SF
Page 35
1-8. Checks on Completion of Installation
5. DI-40 board (MKS-8210HD)/DI-41 board (MKS-8210SD)/DI-43 board (MKS-8210M)
AB C DE F GH J K L MN P R
1
2
TP2000
TP2003
TP2001
TP2004
TP2005
TP2002
TP5007
TP5006
TP5002
TP5005
TP5004
TP5001
TP5003
TP5000
TP5507
TP5506
TP5502
TP5505
TP5504
TP5501
TP5503
TP5500
3
D1
TP3
D2
TP1
4
D3
TP2
5
D5
D6
CN1
6
S1
E1
TP3007
TP3006
TP3002
TP3005
TP3004
TP3001
TP3003
TP3000
TP3507
TP3506
TP3502
TP3505
TP3504
TP3501
TP3503
TP3500
TP8007
TP8006
TP8002
TP8005
TP8004
TP8001
TP8003
TP8000
TP4007
TP4006
TP4002
TP4005
TP4004
TP4001
TP4003
TP4000
TP4507
TP4506
TP4502
TP4505
TP4504
TP4501
TP4503
TP4500
7
E7
8
9
TP2500
TP2503
TP2501
TP2504
TP2505
TP2502
TP1000
TP1003
TP1001
TP1004
TP1005
TP1002
TP1006
TP1007
TP1500
TP1503
TP1501
TP1504
TP1505
TP1502
TP1506
TP1507
TP7000
TP7003
TP7001
TP7004
TP7005
TP7002
TP7006
TP7007
TP7500
TP7503
TP7501
TP7504
TP7505
TP7502
TP7506
TP7507
TP6500
TP6503
TP6501
TP6504
TP6505
TP6502
TP6506
TP6507
TP6000
TP6003
TP6001
TP6004
TP6005
TP6002
E6
10
11
E5
12
13
TP201
TP202
TP203
TP204
DI-40 board A side/Component side
MVS-8000SF
1-27
Page 36
1-8. Checks on Completion of Installation
AB C DE F GH J K L MN P R
1
2
3
D1
TP3
D2
TP1
4
D3
TP2
E1
D5
D6
5
6
7
8
9
10
TP2001
11
12
CN1
S1
TP2000
TP3001 TP3501 TP4501 TP5001
TP3000 TP3500 TP4000 TP4500 TP5000 TP5500
E3
TP2500
TP1001TP2501 TP1501 TP7001 TP7501 TP6001TP6501
TP1000
E4
TP1500 TP6000TP6500TP7000 TP7500
E5
E2
TP4001
E7
TP5501
E6
13
..
. DI-40/41 board
..
<LED>
D1 (A-3) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
D2 (A-4) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D3 (A-4) :
++
+2.5 V
++
+2.5 V power supply status indication.
Lit when the +2.5 V power is supplied.
D5 (A-5) : CONF1 status LED
H2 to L2 FPGA (Spartan II) CONFIG DONE status
indication.
Not lit when configuration is completed.
1-28
TP201
TP202
TP203
TP204
DI-41 board A side/Component side
D6 (A-5) : CONF2 status LED
D10 to L10 FPGA (Spartan II) CONFIG DONE status
indication.
Not lit when configuration is completed.
<Switch>
S1 (A-6) : DI reset switch
Pressing this switch initializes the DI-40 and D-I41 boards.
<Connector>
CN1 (A-6) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
<TEST terminal>
E1 (C-6), E2 (J-2), E3 (P-5), E4 (B-11), E5 (H-11), E6 (N-8),
E7 (A-7) : GND terminal bard
Use this terminal as the earth point for measuring the
respective check terminals.
MVS-8000SF
Page 37
1-8. Checks on Completion of Installation
E1 (A-4), E2 (J-2), E3 (F-6), E4 (D-11), E5 (H-11), E6
(N-8), E7 (L-12) : GND terminal (DI-41 board)
Use this terminal as the earth point for measuring the
respective check terminals.
TP1003 (D-8), TP1503 (E-8), TP2003 (A-8), TP2503 (B-8),
TP3003 (D-5), TP3503 (E-4), TP4003 (H-5), TP4503 (K-5),
TP5003 (L-5), TP5503 (N-5), TP6003 (L-8), TP6503 (K-8),
TP7003 (G-8), TP7503 (H-8), TP8003 (G-4) :
FRAME signal check terminal (DI-40 board)
TP1 (A-4) :
++
+3.3 V check terminal
++
FRAME signal measuring terminal.
+3.3 V measuring terminal.
TP1004 (D-8), TP1504 (E-8), TP2004 (A-8), TP2504 (B-8),
TP2 (A-4) :
+2.5 V measuring terminal.
++
+2.5 V check terminal
++
TP3004 (D-5), TP3504 (E-4), TP4004 (H-5), TP4504 (K-5),
TP5004 (L-5), TP5504 (N-5), TP6004 (L-8), TP6504 (K-8),
TP7004 (G-8), TP7504 (H-8), TP8004 (G-4) : CRC
TP3 (A-3) :
+12 V measuring terminal.
TP201 (N-13) : VD (vertical sync) signal check terminal
VD signal measuring terminal.
++
+12 V check terminal
++
signal check terminal (DI-40 board)
CRC signal measuring terminal.
TP1005 (D-8), TP1505 (E-8), TP2005 (A-8), TP2505 (B-8),
TP3005 (D-5), TP3505 (E-4), TP4005 (H-5), TP4505 (K-5),
TP5005 (L-5), TP5505 (N-5), TP6005 (L-8), TP6505 (K-8),
TP202 (N-13) : CKX (control timing) signal check terminal
CKX signal measuring terminal.
TP7005 (G-8), TP7505 (H-8), TP8005 (G-4) : SIG
DET signal check terminal (DI-40 board)
SIG_DET signal measuring terminal.
TP203 (P-13) : HD (horizontal sync) signal check terminal
HD signal measuring terminal.
TP1006 (D-8), TP1506 (E-8), TP2006 (A-8), TP2506 (B-8),
TP3006 (D-5), TP3506 (E-4), TP4006 (H-4), TP4506 (K-4),
TP204 (P-13) : FLOE (field odd even) signal check
terminal
FLOE signal measuring terminal.
TP5006 (L-4), TP5506 (N-4), TP6006 (L-11), TP6506 (K-8),
TP7006 (G-8), TP7506 (H-8), TP8006 (G-4) : EAV_Y
signal check terminal (DI-40 board)
EAV_Y signal measuring terminal.
TP1000 (D-8), TP1500 (E-8), TP2000 (A-8), TP2500 (B-8),
TP3000 (D-5), TP3500 (E-4), TP4000 (H-5), TP4500 (K-5),
TP5000 (L-5), TP5500 (N-5), TP6000 (L-8), TP6500 (K-8),
TP7000 (G-8), TP7500 (H-8), TP8000 (G-4) : 1R001
signal check terminal (DI-40 board)
1R001 signal measuring terminal.
TP1007 (D-8), TP1507 (E-8), TP2007 (A-8), TP2507 (B-8),
TP3007 (D-5), TP3507 (E-4), TP4007 (H-4), TP4507 (K-4),
TP5007 (L-4), TP5507 (N-4), TP6007 (L-11), TP6507 (K-8),
TP7007 (G-8), TP7507 (H-8), TP8007 (G-4) : EAV_C
signal check terminal (DI-40 board)
EAV_C signal measuring terminal.
TP1001 (D-8), TP1501 (E-8), TP2001 (A-8), TP2501 (B-8),
TP3001 (D-5), TP3501 (E-4), TP4001 (H-5), TP4501 (K-5),
TP5001 (L-5), TP5501 (N-5), TP6001 (L-8), TP6501 (K-8),
TP7001 (G-8), TP7501 (H-8), TP8001 (G-4) : HANC
signal check terminal (DI-40 board)
HANC signal measuring terminal.
TP1000 (E-9), TP1500 (F-9), TP2000 (B-9), TP2500 (C-9),
TP3000 (C-4), TP3500 (E-4), TP4000 (H-4), TP4500 (J-4),
TP5000 (L-4), TP5500 (M-4), TP6000 (M-9), TP6500 (L-9),
TP7000 (H-9), TP7500 (J-9), TP8000 (F-4) :
VCO_FRQ signal check terminal (DI-41 board)
VCO_FRQ signal measuring terminal.
TP1002 (D-8), TP1502 (E-8), TP2002 (A-8), TP2502 (B-8),
TP3002 (D-5), TP3502 (E-4), TP4002 (H-5), TP4502 (K-5),
TP5002 (L-5), TP5502 (N-5), TP6002 (L-8), TP6502 (K-8),
TP7002 (G-8), TP7502 (H-8), TP8002 (G-4) : LINE
signal check terminal (DI-40 board)
LINE signal measuring terminal.
TP1001 (D-11), TP1501 (E-11), TP2001 (A-11),
TP2501 (C-11), TP3001 (D-2), TP3501 (F-2), TP4001 (J-2),
TP4501 (K-2), TP5001 (M-2), TP5501 (N-3), TP6001 (L-11),
TP6501 (K-11), TP7001 (G-11), TP7501 (H-11),
TP8000 (F-4) : EAV_Y signal check terminal (DI-41
board)
EAV_Y signal measuring terminal.
MVS-8000SF
1-29
Page 38
1-8. Checks on Completion of Installation
AB C DE F GH J K L MN P R
1
2
3
4
5
6
7
8
9
10
11
12
D1
TP1
D9551
TP9501
D9051
TP9001
D401
E7
S1
S101
CN101
E2
TP3001
E1
TP2501TP2001
TP1001 TP1501 TP7001 TP7501 TP6501 TP6001
TP3501 TP8001 TP4001 TP4501 TP5001
E3
TP5501
E6
13
..
. DI-43 board
..
<LED>
D1 (A-3) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
D401 (A-6) : CONF ERR status LED
FPGA (EP20K100E) CONFIG DONE status indication.
Not lit when all configurations are completed.
D9051 (A-5) :
++
+1.8 V
++
+1.8 V power supply status indication.
Lit when the +1.8 V power is supplied.
D9551 (A-4) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
DI-43 board A side/Component side
<Switch>
S1 (A-7) : DI reset switch
Pressing this switch initializes the DI-43 board.
S101 (A-8) : JTAG switch
Used only for production in the assembly factory. Set this
switch to ON only when writing program in the JTAG
device with ISP.
<Connector>
CN101 (A-8) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
<TEST terminal>
E1 (C-5), E2 (J-2), E3 (N-3), E4 (C-11), E5 (H-11), E6 (N-10),
E7 (A-6) : GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
1-30
MVS-8000SF
Page 39
1-8. Checks on Completion of Installation
TP1 (A-3) :
++
+12 V check terminal
++
+12 V measuring terminal.
TP501 (P-13) : HD (horizontal sync) signal check terminal
HD signal measuring terminal.
TP1001 (D-8), TP1501 (E-8), TP2001 (A-8), TP2501 (C-8),
TP3001 (D-5), TP3501 (F-5), TP4001 (H-5), TP4501 (K-5),
TP5001 (L-5), TP5501 (N-5), TP6001 (L-8), TP6501 (K-8),
TP7001 (G-8), TP7501 (H-8), TP8001 (G-5) : ERR
check terminal
SDI signal error measuring terminal.
TP9001 (A-5) :
++
+1.8 V check terminal
++
+1.8 V measuring terminal.
TP9501 (A-4) :
++
+3.3 V check terminal
++
+3.3 V measuring terminal.
MVS-8000SF
1-31
Page 40
1-8. Checks on Completion of Installation
6. DIF-119 board (MKS-8170HD)/DIF-122 board (MKS-8170SD)/DIF-141 board (MKS-8170M)
AB C DE F GH J K L MN P R
1
2
E3411
S2301
CN2301
CN2700
TP2301
S2300
3
4
5
6
7
8
9
10
11
12
13
D3404
D3402
D3401
D3400
DI1
DI4
SW1
SW2
E3421
E3429
D2800
D3100
D2700
D2703
D2702
D2701
E2300
CPU-DK
Module
DI8
DI7
DI6
DI3
DI2
E3426
E3425
E3419
TP3309
E3417
E3412
E3407
A
B
C
D
E
F
12345
E3410
TP1305
TP1304
TP1301
TP1303TP1302
TP1300
TP1500
TP3304
TP3305
TP3306
TP3307
E3427
TP3308
TP3301
E3408
TP3302
TP3300
TP3303
E3404
DIF-119 board A side/Component side
1-32
MVS-8000SF
Page 41
1-8. Checks on Completion of Installation
AB C DE F GH J K L MN P R
1
E3411
S2301
CN2301
CN2700
S2300
2
3
4
5
6
7
8
9
10
11
12
13
TP3401
D3404
TP3402
D3402
TP3400
D3401
TP3403
D3400
DI1
DI4
SW2
SW1
E3429
D2800
D3100
D2700
D2703
D2702
D2701
E2300
CPU-DK
Module
DI8
DI7
DI6
E3421
DI3
DI2
E3426
12345
A
B
C
D
E
F
TP1400
E3425
E3419
E3410
TP3310
TP1500TP1600
TP3307
TP3306
E3417
TP3304
TP3305
TP3308
E3427
E3414
E3408
TP3302
E3412
E3407
TP3303
E3404
..
. DIF-119/122 board
..
<LED>
D2700 (B-6) : TBC-1 system status LED
TBC-1 system CONFIG DONE status indication.
Not lit when configuration is completed.
D2701 (B-7), D2702 (B-6), D2703 (B-6) : MAIN CPU
status LED
Main CPU status indication.
D2800 (B-6) : XPT status LED
XPT CONFIG DONE status indication.
Not lit when configuration is completed.
D3100 (B-6) : TBC-2 system status LED
TBC-2 system CONFIG DONE status indication.
Not lit when configuration is completed.
D3400 (A-5) :
++
+1.8 V
++
+1.8 V power supply status indication.
Lit when the +1.8 V power is supplied.
DIF-122 board A side/Component side
D3401 (A-5) :
++
+2.5 V
++
+2.5 V power supply status indication.
Lit when the +2.5 V power is supplied.
D3402 (A-5) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D3404 (A-4) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
D3406 (A-5) :
++
+5 V
++
+5 V power supply status indication.
Lit when the +5 V power is supplied.
MVS-8000SF
1-33
Page 42
1-8. Checks on Completion of Installation
<Switch>
S2300 (A-9) : RESET switch
Pressing this switch resets the DIF-119 and 122 board.
S2301 (A-5) : MONITOR reset switch
The reset switch that is used to reset the monitor in the
maintenance from the TERMINAL.
<Connector>
CN2301 (A-6) : TERMINAL pin
This pin is connected to the CPU control terminal and used
during maintenance. Conforms to RS-232C.
CN2700 (A-6) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
<TEST terminal>
E2300 (B-8), E3404 (P-13), E3407 (N-8), E3408 (L-11),
E3410 (E-12), E3411 (P-1), E3412 (N-5), E3417 (K-5),
E3419 (E-7), E3421 (B-13), E3425 (E-3), E3426 (C-5),
E3427 (J-13), E3429 (B-5) : GND terminal (DIF-119
board)
Use this terminal as the earth point for measuring the
respective check terminals.
E2300 (B-8), E3404 (P-13), E3407 (N-8), E3408 (L-11),
E3410 (E-12), E3411 (P-1), E3412 (N-5), E3414 (L-2),
E3417 (K-5), E3419 (E-7), E3421 (B-13), E3425 (E-3),
E3426 (D-5), E3427 (K-12), E3429 (B-5) : GND
terminal (DIF-122 board)
Use this terminal as the earth point for measuring the
respective check terminals.
TP1300 (G12) : 1.001 signal check terminal (DIF119 board)
1.001 signal measuring terminal.
TP1301 (G-12) : HANC signal check terminal (DIF119 board)
HANC signal measuring terminal.
TP1302 (G-12) : LINE signal check terminal (DIF119 board)
LINE signal measuring terminal.
TP1303 (G-12) : FRAME signal check terminal
(DIF-119 board)
FRAME signal measuring terminal.
TP1304 (G-12) : CRC signal check terminal (DIF119 board)
CRC signal measuring terminal.
TP1305 (G-12) : SIGDET signal check terminal
(DIF-119 board)
SIGDET signal measuring terminal.
TP1500 (J-11) : RCLK signal check terminal (DIF119 board)
RCLK signal measuring terminal.
TP2301 (A-9) : CPU CK (CPU clock) signal check
terminal (DIF-119 board)
Used to check the CPU clock.
TP3300 (L-12) : FLOE (field odd even) signal
check terminal (DIF-119 board)
FLOE signal measuring terminal.
TP3301 (L-13) : HD (horizontal sync) signal check
terminal (DIF-119 board)
HD signal measuring terminal.
TP3302 (L-13) : CKX (control timing) signal check
terminal (DIF-119 board)
CKX signal measuring terminal.
TP3303 (M-13) : VD (vertical sync) signal check
terminal (DIF-119 board)
VD signal measuring terminal.
TP3304 (J-12) : VDO signal check terminal (DIF119 board)
VDO signal measuring terminal.
TP3305 (J-12) : HDO signal check terminal (DIF119 board)
HDO signal measuring terminal.
TP3306 (J-12) : FLOEO signal check terminal (DIF119 board)
FLOEO signal measuring terminal.
TP3307 (J-12) : CKXO signal check terminal (DIF119 board)
CKXO signal measuring terminal.
1-34
MVS-8000SF
Page 43
1-8. Checks on Completion of Installation
TP3308 (L-12) : CK (clock for video signal) signal
(DIF-119 board)
Uses this terminal when checking the clock signal for video.
TP3309 (H-5) : CK2 signal check terminal (DIF-119
board)
Uses this terminal when checking the clock signal for video.
TP1300 (F-12), TP1400 (D-12), TP1500 (J-12) ,
TP1600 (H-12) : VCO_FRQ signal check terminal
VCO_FRQ signal measuring terminal.
TP3302 (M-13) : CKX (control timing) signal check
terminal (DIF-122 board)
CKX signal measuring terminal.
TP3303 (M-13) : VD (vertical sync) signal check
terminal (DIF-122 board)
VD signal measuring terminal.
TP3304 (K-11) : VDO signal check terminal (DIF122 board)
VDO signal measuring terminal.
TP3401 (A-4) :
++
+12 V check terminal (DIF-122
++
board)
+12 V measuring terminal.
TP3402 (A-4) :
++
+3.3 V check terminal (DIF-122
++
board)
+3.3 V measuring terminal.
TP3403 (A-5) :
++
+1.8 V check terminal (DIF-122
++
board)
+1.8 V measuring terminal.
<LED on the CPU DK module> (C-10)
Refer to < LED on the CPU DR module > in “1. CA-44
board”.
<Switch on the CPU DK module> (C-10)
Refer to < Switch on the CPU DR module > in “1. CA-44
board”.
TP3305 (K-11) : HDO signal check terminal (DIF122 board)
HDO signal measuring terminal.
TP3306 (K-12) : FLOEO signal check terminal
(DIF-122 board)
FLOEO signal measuring terminal.
TP3307 (K-12) : CKXO signal check terminal (DIF122 board)
CKXO signal measuring terminal.
TP3308 (K-12) : CK27 signal check terminal (DIF122 board)
CK27 signal measuring terminal.
TP3310 (H-4) : CK1 signal check terminal (DIF-122
board)
Used to check the CK1 signal.
TP3400 (A-5) :
++
+2.5 V check terminal (DIF-122
++
board)
+2.5 V measuring terminal.
MVS-8000SF
1-35
Page 44
1-8. Checks on Completion of Installation
AB C DE F GH J K L MN P R
1
E3411
S2301
CN2301
CN2700
TP2301
S2300
2
3
4
5
6
7
8
9
10
11
12
13
TP3700
D3700
TP3600
D3703
TP3500
D3702
TP3400
D3701
D2700
S2700
DI1
DI4
SW2
SW1
E3429
D2703
D2702
D2701
E2300
CPU-DK
Module
DI8
DI7
DI6
E3421
DI3
DI2
E3426
12345
E3414
E3425
E3427
E3417
E3408
TP3300
TP3308
TP3301 TP3302
TP3309
E3419
A
B
C
D
E
F
TP1400
TP1300
E3410
E3412
E3407
TP3303
E3404
DIF-141 board A side/Component side
..
. DIF-141 board
..
<LED>
D2700 (A-7) : CONF ERR status LED
FPGA (EP20K100E and Spartan II) CONFIG DONE
status indication.
Not lit when all configurations are completed.
D2701 (B-7), D2702 (B-6), D2703 (B-6) : MAIN CPU
status LED
Main CPU status indication.
D3700 (A-4) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
D3701 (A-5) :
++
+1.8 V
++
+1.8 V power supply status indication.
Lit when the +1.8 V power is supplied.
D3702 (A-5) :
++
+2.5 V
++
+2.5 V power supply status indication.
Lit when the +2.5 V power is supplied.
D3703 (A-4) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
<Switch>
S2300 (A-9) : RESET switch
Pressing this switch resets the DIF-141 board.
S2301 (A-5) : MONITOR reset switch
The reset switch that is used to reset the monitor in the
maintenance from the TERMINAL.
1-36
MVS-8000SF
Page 45
1-8. Checks on Completion of Installation
S2700 (A-7) : JTAG switch
Used only for production in the assembly factory. Set this
switch to ON only when writing program in the JTAG
device with ISP.
<Connector>
CN2301 (A-6) : TERMINAL pin
This pin is connected to the CPU control terminal and used
during maintenance. Conforms to RS-232C.
CN2700 (A-6) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
<TEST terminal>
E2300 (B-8), E3404 (P-13), E3407 (N-8), E3408 (L-11),
E3410 (G-13), E3411 (P-1), E3412 (N-5), E3414 (L-2)
E3417 (K-5), E3419 (E-7), E3421 (B-13), E3425 (E-3),
E3426 (D-5),
E3427 (K-12), E3429 (B-5) : GND
terminal
Use this terminal as the earth point for measuring the
respective check terminals.
TP1300 (G-13), TP1400 (E-13) : ERR check
terminal
SDI signal error measuring terminal.
TP3309 (H-5) : CK2 signal check terminal
Uses this terminal when checking the clock signal for video.
TP3310 (G-11) : CK3 signal check terminal
Uses this terminal when checking the clock signal for video.
TP3400 (A-5) :
++
+1.8 V check terminal
++
+1.8 V measuring terminal.
TP3500 (A-4) :
++
+2.5 V check terminal
++
+2.5 V measuring terminal.
TP3600 (A-4) :
++
+3.3 V check terminal
++
+3.3 V measuring terminal.
TP3700 (A-4) :
++
+12 V check terminal
++
+12 V measuring terminal.
<LED on the CPU DK module> (C-10)
Refer to < LED on the CPU DR module > in “1. CA-44
Board”.
<Switch on the CPU DK module> (C-10)
Refer to < Switch on the CPU DR module > in “1. CA-44
Board”.
TP2301 (A-9) : CPU CK (CPU clock) signal check
terminal
Used to check the CPU clock.
TP3300 (L-13) : FLOE (field odd even) signal
check terminal
FLOE signal measuring terminal.
TP3301 (M-13) : HD (horizontal sync) signal check
terminal
HD signal measuring terminal.
TP3302 (M-13) : CKX (control timing) signal check
terminal
CKX signal measuring terminal.
TP3303 (M-13) : VD (vertical sync) signal check
terminal
VD signal measuring terminal.
TP3308 (L-12) : CK1 (clock for video signal) signal
Uses this terminal when checking the clock signal for video.
MVS-8000SF
1-37
Page 46
1-8. Checks on Completion of Installation
7. XPT-21 board (MVS-8000SF)
AB C DE F GH J K L MN P R
1
2
TP2
3
4
5
6
7
8
9
10
CN3901
11
12
13
CN3301
D3401
D2
D3
D4
CN3303
CN3001
S3401
S3301
TP1
DI1
DI4
SW2
SW1
CPU-DK
Module
D8D7D6D3D2
E10
E9
A
B
C
D
TP3401
E
F
12345
E7
E1
E8
E2
E5
E3
TP3001E4
E6
TP3004
TP3003
TP3005
TP3002
A side/Component side
<LED>
D3401 (A-5) : RESET status LED
System reset status indication.
Lit when S3401 is pressed or the power voltage drops to
+3.3 V.
D3 (A-5) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D4 (A-6) :
++
+2.5 V
++
+2.5 V power supply status indication.
Lit when the + 2.5 V power is supplied.
D2 (A-5) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
1-38
<Switch>
S3401 (A-8) : XPT-RESET switch
Pressing this switch initializes the CPU on the XPT-21
board.
S3301 (A-10) : MONITOR switch
Factory use only. (Do not change the setting.)
<Connector>
CN3001 (A-8) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
CN3301 (A-4) : TERMINAL pin
This pin is connected to the CPU control terminal and used
during maintenance.
Conforms to RS-232C.
MVS-8000SF
Page 47
1-8. Checks on Completion of Installation
CN3303 (A-6) : DEBUG terminal
Not used.
This terminal conforms to RS-232C.
CN3901 (A-11) : IEEE1394 terminal
Not used.
This terminal conforms to IEEE1394.
<TEST terminal>
E1 (P-4), E2 (P-8), E3 (P-12), E4 (L-12), E5 (J-11),
E6 (H-13), E7 (H-4), E8 (H-8), E9 (D-8), E10 (E-4) :
GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
TP1 (B-4) :
++
+
3.3 V check terminal
++
+3.3 V measuring terminal.
TP2 (D-3) :
++
+2.5 V check terminal
++
+2.5 V measuring terminal.
TP3001 (M-12) : VCLK signal check terminal
VCLK signal measuring terminal.
<LED on the CPU DK module> (C-10)
Refer to < LED on the CPU DK module > in “1. CA-44
board”.
<Switch on the CPU DK module> (C-10)
Refer to < Switch on the CPU DK module > in “1. CA-44
board”.
TP3002 (L-13) : VD (vertical sync) signal check
terminal
VD signal measuring terminal.
TP3003 (L-13) : HD (horizontal sync) signal check
terminal
HD signal measuring terminal.
TP3004 (L-13) : FLOE (Field Odd Even) signal
check terminal
FLOE signal measuring terminal.
TP3005 (L-13) : CKX (control timing) signal check
terminal
CKX signal measuring terminal.
TP3401 (H-12) : EXT_CLK check terminal
CPU clock measuring terminal.
(KOA CPU clock check terminal)
MVS-8000SF
1-39
Page 48
1-8. Checks on Completion of Installation
8. OUT-23 board (MKS-8160HD)/OUT-24 board (MKS-8160SD)/OUT-27 board (MKS-8160M)
AB C DE F GH J K L MN P R
1
2
3
4
5
6
7
8
9
10
11
12
13
S100
D100
TP101
D104
TP102
D105
TP103
D106
TP104
D1400
D1401
CN1400
S1501
CN1502
D503
D502
D501
DI1
DI4
SW2
SW1
CPU-DK
Module
D8D7D6D3D2
TP1006TP1106TP1206TP1306
TP1008TP1108TP1208TP1308
TP1007TP1107TP1207TP1307
TP1002
TP1005
TP1004
TP1003
TP502
TP501
E107
TP606
E102
E103
TP206 TP207
TP1001
TP1000
TP706TP806TP906
A
B
C
*
D
TP908
TP907
TP808
TP807
E
F
12345
E104
TP205
TP708
TP707
TP601
TP600
TP203
TP204
TP608
TP607
TP602
TP605
TP604
TP603
TP202
TP201
E105
OUT-23 board A side/Component side* : The CPU-DK module is installed only in the OUT-23 board of slot 14.
1-40
MVS-8000SF
Page 49
1-8. Checks on Completion of Installation
AB C DE F GH J K L MN P R
1
2
S100
D100
3
TP101
D107
D104
TP102
4
D105
TP103
D106
TP104
D1400
5
D1401
CN1400
6
7
S1501
CN1502
D503
8
D502
D501
9
A
E103
E108
TP1001TP1101TP1201TP1301
TP1000TP1100TP1200TP1300
TP701TP801TP901
TP601
E101
TP1002TP1102TP1202TP1302
TP502
TP501
E107
DI1
10
DI4
11
SW1
12
13
SW2
CPU-DK
Module
D8D7D6D3D2
B
C
*
D
E
F
12345
E109
* : The CPU-DK module is installed only in the OUT-24 board of slot 14.
..
. OUT-23/24 board
..
<LED>
D100 (A-3) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
D104 (A-3) :
++
+5 V (OUT-23 board)
++
+5 V power supply status indication.
Lit when the +5 V power is supplied.
D104 (A-4), D107 (A-3) :
++
+5 V (OUT-24 board)
++
+5 V power supply status indication.
Lit when the +5 V power is supplied.
D105 (A-4) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
TP602
TP204
TP203
TP202
TP201
E105
TP800
TP702TP802TP902
TP600TP700TP900
E104
TP205
OUT-24 board A side/Component side
D106 (A-4) :
++
+2.5 V
++
+2.5 V power supply status indication.
Lit when the +2.5 V power is supplied.
D501, D502, D503 (A-8) : OUT-CPU status LED
OUT-23 and OUT-24 boards CPU status indication.
D1400 (A-5) : TBC-1 system status LED
TBC-1 system CONFIG DONE status indication.
Not lit when configuration is completed.
D1401 (A-5) : TBC-2 system status LED
TBC-2 system CONFIG DONE status indication.
Not lit when configuration is completed.
MVS-8000SF
1-41
Page 50
1-8. Checks on Completion of Installation
<Switch>
S100 (A-3) : OUT-CPU RESET switch
Pressing this switch initializes the CPU on the OUT-23/24
board.
S1501 (A-7) : MONITOR reset switch
The reset switch that is used to reset the monitor during
maintenance through the terminal.
<Connector>
CN1400 (A-5) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
CN1502 (A-8) : TERMINAL pin
This pin is connected to the control terminal and used
during maintenance.
<TEST terminal>
E102 (E-7), E103 (H-6), E104 (J-12), E105 (P-13),
E107 (P-6) : GND terminal (OUT-23 board)
Use this terminal as the earth point for measuring the
respective check terminals.
TP203 (N-12) : HD (horizontal sync) signal check
terminal (OUT-23 board)
HD signal measuring terminal.
TP204 (N-13) : FLOE (field odd even) signal check
terminal
FLOE signal measuring terminal.
TP203 (P-12) : HD (horizontal sync) signal check
terminal (OUT-24 board)
HD signal measuring terminal.
TP204 (P-12) : FLOE (Field Odd Even) signal
check terminal
FLOE signal measuring terminal.
TP205 (J-13), TP206 (J-7) : CK (clock for video)
signal check terminal (OUT-23 board)
Uses this terminal when checking the clock signal for video.
TP205 (J-13), TP206 (J-6) : EAV_C signal check
terminal (OUT-24 board)
CLOCK signal measuring terminal.
E103 (J-6), E104 (K-13), E105 (P-13), E107 (P-5),
E109 (D-13), E108 (J-1), E1010 (P-1) : GND
terminal (OUT-24 board)
TP207 (K-7) : VCO CLOCK signal check terminal
(OUT-23 board)
VCO CLOCK signal measuring terminal.
Use this terminal as the earth point for measuring the
respective check terminals.
TP501 (P-5) : CPU_OE signal check terminal
CPU_OE signal measuring terminal.
TP101 (A-3) :
+12 V measuring terminal.
++
+12 V check terminal
++
TP502 (P-5) : CPU_WE signal check terminal
CPU_WE signal measuring terminal.
TP102 (A-4) :
+5 V measuring terminal.
++
+5 V check terminal
++
TP600 (N-12), TP1000 (N-5) : 1R001 signal check
terminal (OUT-23 board)
TP103 (A-4) :
++
+3.3 V check terminal
++
1R001 signal measuring terminal.
+3.3 V measuring terminal.
TP601 (N-12), TP1001 (N-5) : HANC signal check
TP104 (A-4) :
+2.5 V measuring terminal.
TP104 (A-5) :
+2.5 V measuring terminal.
++
+2.5 V check terminal (OUT-23 board)
++
++
+2.5 V (OUT-24 board)
++
terminal (OUT-23 board)
HANC signal measuring terminal.
TP602 (N-11), TP1002 (N-5) : LINE signal check
terminal (OUT-23 board)
LINE signal measuring terminal.
TP201 (P-13) : VD (vertical sync) signal check terminal
VD signal measuring terminal.
TP603 (N-12), TP1003 (N-5) : FRAME signal check
terminal (OUT-23 board)
TP202 (P-12) : CKX (control timing) signal check terminal
FRAME signal measuring terminal.
CKX signal measuring terminal.
1-42
MVS-8000SF
Page 51
TP604 (N-12), TP1004 (N-5) : CRC signal check
terminal (OUT-23 board)
CRC signal measuring terminal.
TP605 (N-11), TP1005 (N-5) : SIG_DET signal
check terminal (OUT-23 board)
SIG_DET signal measuring terminal.
TP606 (N-8), TP706 (L-9), TP806 (J-9), TP906 (G-9),
TP1006 (N-2), TP1106 (L-2), TP1206 (J-2), TP1306
(F-2) : PLL_LOCK signal check terminal (OUT-23
board)
PLL_LOCK signal measuring terminal.
TP607 (N-10), TP707 (L-10), TP807 (J-10), TP907
(G-10), TP1007 (N-4), TP1107 (L-4), TP1207 (J-4),
TP1307 (F-4) : EAV_Y signal check terminal (OUT23 board)
EAV_Y signal measuring terminal.
1-8. Checks on Completion of Installation
TP602 (P-10), TP702 (L-10), TP802 (J-10), TP902 (G-10),
TP1002 (N-4), TP1102 (L-4), TP1202 (J-4), TP1302 (F-4) :
EAV_Y signal check terminal (OUT-24 board)
EAV_Y signal measuring terminal.
TP608 (N-10), TP708 (L-10), TP808 (J-10), TP908 (G-10),
TP1008 (N-3), TP1108 (L-3), TP1208 (J-4), TP1308 (F-4) :
EAV_C signal check terminal (OUT-23 board)
EAV_C signal measuring terminal.
TP600 (M-12), TP601 (M-8), TP700 (K-11), TP701 (K-8),
TP800 (H-12), TP801 (H-8), TP900 (E-12), TP901 (F-8),
TP1000 (M-5), TP1001 (M-2), TP1100 (J-5), TP1101 (K-2),
TP1200 (G-5), TP1201 (G-2), TP1300 (E-5), TP1301 (E-2) :
V_FRQ signal check terminal (OUT-24 board)
V_FRQ signal measuring terminal.
<LED on the CPU DK module> (C10)
Refer to < LED on the CPU DR module > in “1. CA-44
board”.
<Switch on the CPU DK module> (C10)
Refer to < Switch on the CPU DR module > in “1. CA-44
board”.
MVS-8000SF
1-43
Page 52
1-8. Checks on Completion of Installation
ABCDEFGHJ K LMNP
1
2
S1
D1
3
TP1
D9504
D9004
TP9001
TP9501
4
D1600
S1600
E1
5
CN1400
6
E5
TP1200TP1300TP1400TP1500
TP702
TP701
E2
TP700
E3
E6
TP800TP900TP1000TP1100
TP205E7
TP203
TP204
TP202
TP201
E4
7
8
9
10
11
12
S2100
CN1902
D702
D701
D700
DI1
DI4
SW2
SW1
TP2100
CPU-DK
Module
D8D7D6D3D2
A
B
C
*
D
E
F
12345
* : The CPU-DK module is installed only in the OUT-27 board of slot 14. OUT-27 board A side/Component side
..
. OUT-27 board
..
<LED>
D1 (A-3) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
<Switch>
S1 (A-3) : OUT-CPU RESET switch
Pressing this switch initializes the CPU on the OUT-27
board.
If this LED does not light, the fuse may have blown.
S1600 (A-5) : JTAG switch
D700, D701, D702 (A-8) : OUT-CPU status LED
OUT-27 board CPU status indication.
Used only for production in the assembly factory. Set this
switch to ON only when writing program in the JTAG
device with ISP.
D1600 (A-4) : CONF ERR status LED
FPGA (EP20K100E) CONFIG DONE status indication.
Not lit when all configurations are completed.
S2100 (A-7) : MONITOR reset switch
The reset switch that is used to reset the monitor during
maintenance through the terminal.
D9004 (A-4) :
++
+1.8 V
++
+1.8 V power supply status indication.
Lit when the +1.8 V power is supplied.
D9504 (A-3) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
1-44
MVS-8000SF
Page 53
1-8. Checks on Completion of Installation
<Connector>
CN1600 (A-5) : ISP common connector
Used only for production in the assembly factory. Used for
TP2100 (B-8) : CPU CK (CPU clock) signal check
terminal
Uses this terminal when checking the CPU clock.
program writing into the JTAG device with ISP.
TP9001 (A-4) :
CN1902 (A-7) : TERMINAL pin
+1.8 V measuring terminal.
This pin is connected to the control terminal and used
during maintenance.
TP9501 (A-4) :
+3.3 V measuring terminal.
<TEST terminal>
E1 (A-5), E2 (N-1), E3 (N-5), E4 (N-12), E5 (J-1), E6 (G-7),
E7 (G-12) : GND terminal
Use this terminal as the earth point for measuring the
<LED on the CPU DK module> (C10)
Refer to < LED on the CPU DR module > in “1. CA-44
Board”.
respective check terminals.
<Switch on the CPU DK module> (C10)
TP1 (A-3) :
++
+12 V check terminal
++
+12 V measuring terminal.
Refer to < Switch on the CPU DR module > in “1. CA-44
Board”.
TP201 (M-12) : VD (vertical sync) signal check terminal
VD signal measuring terminal.
TP202 (M-12) : CKX (control timing) signal check terminal
CKX signal measuring terminal.
++
+1.8 V check terminal
++
++
+3.3 V check terminal
++
TP203 (M-12) : HD (horizontal sync) signal check
terminal
HD signal measuring terminal.
TP204 (M-12) : FLOE (field odd even) signal check
terminal
FLOE signal measuring terminal.
TP205 (J-12), TP206 (J-7) : CK (clock for video)
signal check terminal
Uses this terminal when checking the clock signal for video.
TP700 (N-3) : CPU_CS2 signal check terminal
CPU_CS2 signal measuring terminal.
TP701 (M-5) : CPU_OE signal check terminal
CPU_OE signal measuring terminal.
TP702 (M-5) : CPU_WE signal check terminal
CPU_WE signal measuring terminal.
TP800 (L-11), TP900 (K-11), TP1000 (H-11), TP1100 (G-11),
TP1200 (L-5), TP1300 (K-5), TP1400 (H-5), TP1500 (G-5) :
ERR check terminal
SDI signal error measuring terminal.
MVS-8000SF
1-45
Page 54
1-8. Checks on Completion of Installation
9. DIO-62 board (MKS-8440HD)/DIO-63 board (MKS-8440SD)/DIO-74 board (MKS-8440M)
AB C DE F GH J K L MN P R
1
2
3
TP2
TP100
4
TP1
TP3
5
6
7
S1
D1
D5
D6
D7
D100
D101
TP2000
TP2001
TP2002
E5
TP2501
TP2502
TP2500
TP3001
TP3002
E4
TP4
TP3000
TP3501
TP3502
TP3500
E1
E2
8
E6
9
TP4001
TP4002
TP4000
TP4501
TP4502
TP4500
TP5001
TP5002
TP5000
TP5501
TP5502
TP5500
10
TP1007
TP1006
TP1002
11
TP1005
TP1004
TP1001
TP1503
TP1000
12
13
TP1507
TP1506
TP1502
TP1505
TP1504
TP1501
TP1503
TP1500
E7
TP5TP6
TP7
TP8
TP9
E3
TP10
DIO-62 board A side/Component side
1-46
MVS-8000SF
Page 55
1-8. Checks on Completion of Installation
AB C DE F GH J K L MN P R
1
2
D1
3
TP2
D6
TP1
D7
4
TP3
E6
5
D100
D101
6
CN1
7
S1
8
TP1001
9
10
TP1500
TP1000
11
12
13
E7
TP2000
E5
TP4000
TP1501
TP4002
TP2500 TP3000 TP3500
TP2001
TP4001
TP6
TP2501
TP2502TP2002
E4
TP4500 TP5000 TP5500
TP4501
TP4502
TP5
TP4
TP3001
TP3002
TP5001
TP5002
TP7
TP8
TP9
TP10
TP5501
TP5502
E1
TP3501
TP3502
E2
E3
..
. DIO-62/63 board
..
<LED>
D1 (A-3) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
D5 (A-3) :
++
+5 V (DIO-62 board)
++
+5 V power supply status indication.
Lit when the +5 V power is supplied.
D6 (A-4) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D7 (A-5) :
++
+2.5 V
++
+2.5 V power supply status indication.
Lit when the +2.5 V power is supplied.
DIO-63 board A side/Component side
D100 (A-5) : CONF1
H2 to L2 FPGA (Spartan II) CONFIG DONE status
indication.
Not lit when configuration is completed.
D101 (A-6) : CONF2
D10 to L10 FPGA (Spartan II) CONFIG DONE status
indication.
Not lit when configuration is completed.
<Switch>
S1 (A-7) : DIO reset switch
Pressing this switch initializes the CPU on the DIO-62 and
DIO-63 board.
<Connector>
CN1 (A-6) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
MVS-8000SF
1-47
Page 56
1-8. Checks on Completion of Installation
<TEST terminal>
E1 (N-3), E2 (P-6), E3 (P-11), E4 (H-6), E5 (F-3), E6 (A-8),
E7 (E-12) : GND terminal (DIO-62 board)
Use this terminal as the earth point for measuring the
respective check terminals.
E1 (N-2), E2 (P-6), E3 (P-10), E4 (H-6), E5 (F-3), E6 (A-5),
E7 (A-12) : GND terminal (DIO-63 board)
Use this terminal as the earth point for measuring the
respective check terminals.
TP1 (A-4) :
++
+3.3 V check terminal
++
+3.3 V measuring terminal.
TP2 (A-3) :
++
+12 V check terminal
++
+12 V measuring terminal.
TP4 (K-6), TP5 (L-13), TP6 (H-13) : CK (clock for
video) signal check terminal (DIO-62 board)
Uses this terminal when checking the clock signal for video.
TP7 (N-13) : VD (vertical sync) signal check
terminal (DIO-62 board)
VD signal measuring terminal.
TP8 (P-13) : CKX (control timing) signal check
terminal (DIO-62 board)
CKX signal measuring terminal.
TP9 (P-13) : HD (horizontal sync) signal check
terminal (DIO-62 board)
HD signal measuring terminal.
TP10 (P-13) : FLOE (field odd even) signal check
terminal (DIO-62 board)
FLOE signal measuring terminal.
TP4 (K-6), TP5 (J-13), TP6 (H-13) : CK (clock for
video) signal check terminal (DIO-63 board)
Uses this terminal when checking the clock signal for video.
TP7 (L-12) : VD (vertical sync) signal check
terminal (DIO-63 board)
VD signal measuring terminal.
TP8 (L-12) : CKX (control timing) signal check
terminal (DIO-63 board)
CKX signal measuring terminal.
TP9 (L-12) : HD (horizontal sync) signal check
terminal (DIO-63 board)
HD signal measuring terminal.
TP10 (L-12) : FLOE (field odd even) signal check
terminal (DIO-63 board)
FLOE signal measuring terminal.
TP100 (A-4) :
++
+5 V check terminal (DIO-62 board)
++
+5 V measuring terminal.
TP3 (A-5) :
++
+2.5 V check terminal
++
+2.5 V measuring terminal.
TP1000 (E-11), TP1500 (F-11) : 1R001 signal check
terminal (DIO-62 board)
1R001 signal measuring terminal.
TP1001 (E-11), TP1501 (F-11) : HANC signal check
terminal (DIO-62 board)
HANC signal measuring terminal.
TP1002 (E-11), TP1502 (F-11) : LINE signal check
terminal (DIO-62 board)
LINE signal measuring terminal.
TP1003 (E-11), TP1503 (F-11) : FRAME signal
check terminal (DIO-62 board)
FRAME signal measuring terminal.
TP1004 (E-11), TP1504 (F-11) : CRC signal check
terminal (DIO-62 board)
CRC signal measuring terminal.
TP1005 (E-11), TP1505 (F-11) : SIG DET signal
check terminal (DIO-62 board)
SIG DET signal measuring terminal.
TP1006 (E-11), TP1506 (F-11), TP2001 (G-3),
TP2501 (J-3), TP3001 (K-3), TP3501 (M-3), TP4001 (G-9),
TP4501 (J-9), TP5001 (K-9), TP5501 (M-9) : EAV_Y
signal check terminal (DIO-62 board)
EAV_Y signal measuring terminal.
TP1007 (E-10), TP1507 (F-10), TP2002 (G-3), TP2502 (J-3),
TP3002 (K-3), TP3502 (M-3), TP4002 (G-9), TP4502 (J-9),
TP5002 (K-9), TP5502 (M-9) :
EAV_C signal check
terminal (DIO-62 board)
EAV_C signal measuring terminal.
1-48
MVS-8000SF
Page 57
TP2000 (H-2), TP2500 (K-2), TP3000 (L-3), TP3500
(N-3), TP4000 (L-3), TP4500 (K-8), TP5000 (L-8),
TP5500 (N-8) : PLL_LOCK signal check terminal
(DIO-62 board)
PLL_LOCK signal measuring terminal.
TP1000 (D-11), TP1500 (E-11), TP2000 (G-2),
TP2500 (J-2), TP3000 (K-2), TP3500 (M-2), TP4000 (G-7),
TP4500 (J-7), TP5000 (K-7), TP5500 (M-7) :
VCO_FRQ signal check terminal (DIO-63 board)
VCO_FRQ signal measuring terminal.
TP1001 (E-9), TP1501 (G-9), TP2001 (H-5), TP2501 (J-5),
TP3001 (L-5), TP3501 (N-9), TP4001 (H-10), TP4501 (K-10),
TP5001 (L-10), TP5501 (N-9) : EAV_Y signal check
terminal (DIO-63 board)
EAV_Y signal measuring terminal.
TP2002 (H-5), TP2502 (J-5), TP3002 (L-5), TP3502 (N-4),
TP4002 (H-10), TP4502 (J-10), TP5002 (L-10),
TP5502 (N-10) : EAV_C signal check terminal
(DIO-63 board)
EAV_C signal measuring terminal.
1-8. Checks on Completion of Installation
MVS-8000SF
1-49
Page 58
1-8. Checks on Completion of Installation
AB C DE F GH J K L MN P R
1
2
3
4
5
6
7
8
9
10
11
12
D1
TP1
D3
TP9501
D2
TP9001
D501
E6
S601
CN601
S1
E1
E5
TP102
E4
TP1001
TP1501
E7
TP201
TP202
TP203
TP204
E2
E3
TP101
13
..
. DIO-74 board
..
<LED>
D1 (A-3) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
D2 (A-4) :
++
+1.8 V
++
+1.8 V power supply status indication.
Lit when the +1.8 V power is supplied.
D3 (A-4) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D501 (A-4) : CONF ERR
FPGA (EP20K100E) CONFIG DONE status indication.
Not lit when all configurations are completed.
TP103TP104
DIO-74 board A side/Component side
<Switch>
S1 (A-9) : DIO reset switch
Pressing this switch initializes the CPU on the DIO-74
board.
S601 (A-8) : JTAG switch
Used only for production in the assembly factory. Set this
switch to ON only when writing program in the JTAG
device with ISP.
<Connector>
CN601 (A-8) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
1-50
MVS-8000SF
Page 59
<TEST terminal>
E1 (N-2), E2 (P-6), E3 (P-10), E4 (H-6), E5 (F-3), E6 (A-5),
E7 (C-12) : GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
1-8. Checks on Completion of Installation
TP1 (A-3) :
++
+12 V check terminal
++
+12 V measuring terminal.
TP101 (P-12), TP102 (J-6), TP103 (J-13), TP104 (D-13) :
CK (clock for video) signal check terminal
Uses this terminal when checking the clock signal for video.
TP201 (L-12) : VD (vertical sync) signal check
terminal
VD signal measuring terminal.
TP202 (L-12) : CKX (control timing) signal check
terminal
CKX signal measuring terminal.
TP203 (L-12) : HD (horizontal sync) signal check
terminal
HD signal measuring terminal.
TP204 (L-12) : FLOE (field odd even) signal check
terminal
FLOE signal measuring terminal.
TP9001 (A-4) :
++
+1.8 V check terminal
++
+1.8 V measuring terminal.
TP9501 (A-4) :
++
+3.3 V check terminal
++
+3.3 V measuring terminal.
TP1001 (D-11), TP1501 (E-11) : ERR check terminal
SDI signal error measuring terminal.
MVS-8000SF
1-51
Page 60
1-8. Checks on Completion of Installation
10. MY-102 board (MKS-8440HD/SD/M)
AB C DE F GH J K L MN P R
1
2
3
4
S202
D201
D202
5
D203
S201
D3
D2
6
D1
7
CN14
8
CN12
9
10
11
12
13
D12
SW2
SW1
D10
D13
D18
D19
D14
D15
D16
D17
B
A
TP203
TP204
E
D
C
CPU-DR
Module
E601
G
F
654321
E508
TP504
TP506
TP505
TP507
TP905
TP904
TP704
E801
TP906
E1001
E123
E131TP706TP705
E124
E132
E121
E130
E122
E129
<LED>
D1, D2, D3 (A-6) : MY-CPU status LED
Status indication of the CPU on the MY-102 board.
D201 (A-5) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
D202 (A-5) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D203 (A-5) :
++
+1.8 V
++
+1.8 V power supply status indication.
Lit when the +1.8 V power is supplied.
A side/Component side
<Switch>
S201 (A-5) : MY-CPU reset switch
Pressing this switch initializes the CPU on the MY-102
board.
S202 (A-5) : MONITOR reset switch
The reset switch that is used to reset the monitor during
maintenance through the terminal.
<Connector>
CN12 (A-8) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
CN14 (A-7) : TERMINAL pin
This pin is connected to the CPU control terminal and used
during maintenance.
Conforms to RS-232C.
1-52
MVS-8000SF
Page 61
<TEST terminal>
E121 (P-8), E122 (P-10), E123 (P-3), E124 (P-4),
E129 (P-11), E130 (P-9), E131 (P-4), E132 (P-5),
E508 (E-12), E601 (D-7), E801 (N-7), E1001 (N-12) :
GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
1-8. Checks on Completion of Installation
TP203 (C-3) :
++
+3.3 V check terminal
++
+3.3 V measuring terminal.
TP204 (C-5) :
++
+1.8 V check terminal
++
+1.8 V measuring terminal.
TP504 (F-2) : CKX (control timing) signal check
terminal
CKX signal measuring terminal.
TP505 (E-12), TP706 (L-4), TP906 (L-8) : FLOE
(field odd even) signal check terminal
FLOE signal measuring terminal.
TP506 (E-12), TP704 (L-4), TP904 (K-8) : VD
(vertical sync) signal check terminal
VD signal measuring terminal.
TP507 (F-12), TP705 (K-4), TP905 (K-8) : HD
(horizontal sync) signal check terminal
HD signal measuring terminal.
<LED on the CPU DR module> (C-10)
Refer to < LED on the CPU DR module > in “1. CA-44
board”.
<Switch on the CPU DR module> (C-10)
Refer to < Switch on the CPU DR module > in “1. CA-44
board”.
MVS-8000SF
1-53
Page 62
1-8. Checks on Completion of Installation
11. CC-90 board (MKS-8420M)
ABCDEFGHJ KLMNPR
1
2
TP101
D107
3
TP9501
D101
TP9001
D102
4
TP9301
D103
10
11
12
13
5
6
7
8
9
CN401
S101
E101
S2001
CN2001
TP402
S400
D12
SW2
SW1
D10
D13
D803
D804
D805
D801
D802
E106
A
D18
D19
D14
D15
D16
D17
B
E107
E103
TP401
TP400
E
D
C
CPU-DR
Module
F
G
654321
E108
TP1200
TP205
TP202
TP201
E105
TP900
E104
TP204
TP203
<LED>
D107 (A-3) :
++
+12 V
++
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light on, the fuse may have blown.
D101 (A-3) :
++
+3.3 V
++
+3.3 V power supply status indication.
Lit when the +3.3 V power is supplied.
D102 (A-4) :
++
+1.8 V-1
++
+1.8 V-1 power supply status indication.
Lit when the +1.8 V-1 power is supplied.
D103 (A-4) :
++
+1.8 V-2
++
+1.8 V-2 power supply status indication.
Lit when the +1.8 V-2 power is supplied.
A side/Component side
D803, D804, D805 (A-10) : CC-CPU status LED
Indicates the CPU status on the CC-90 board.
D801 (A-10) : DLL status LED
Indicates lock/unlock of the DLL (Delay Locked Loop) in
the CC-90 board.
If this LED lit, the DLL can possibly be unlocked.
D802 (A-10) : FPGA CONFIG status LED
CC-90 board FPGA CONFIG DONE status indication.
Not lit when all configurations are completed.
1-54
MVS-8000SF
Page 63
1-8. Checks on Completion of Installation
<Switch>
S2001 (A-5) : JTAG switch
Used only for production in the assembly factory. Set this
switch to ON only when writing program in the JTAG
device with ISP.
S101 (A-8) : CC-CPU reset switch
Pressing this switch initializes the CPU on the CC-90
board.
S400 (A-8) : Monitor reset switch
The reset switch that is used to reset the monitor during
maintenance through the terminal.
<Connector>
CN2001 (A-6) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
CN401 (A-7) : Terminal pin
This pin is connected to the control terminal and used
during maintenance.
Conforms to RS-232C.
<TEST terminal>
E101 (A-5), E103 (D-5), E104 (L-12), E105 (N-8),
E106 (B-8), E107 (B-13), E108 (J-9) : GND terminal
Use this terminal as the earth point for measuring the
respective check terminals.
TP401 (C-7) : CPU half clock signal check
terminal
Use this terminal to check the CPU half clock signal.
TP402 (B-7) : CPU clock signal check terminal
Use this terminal to check the CPU clock signal.
TP900 (M-10), TP1200 (K-10) : ERR check terminal
SDI signal error measuring terminal.
TP201 (L-13) : VD (vertical sync) signal check
terminal
Use this terminal to check the VD signal that is used in this
circuit board.
TP202 (L-12) : CKX (control timing) signal check
terminal
Use this terminal to check the CKX signal that is used in
this circuit board.
TP203 (M-13) : HD (horizontal sync) signal check
terminal
Use this terminal to check the HD signal that is used in this
circuit board.
TP204 (M-12) : FLOE (field odd even) signal check
terminal
Use this terminal to check the FLOE signal that is used in
this circuit board.
TP101 (A-3) :
++
+12 V check terminal
++
+12 V measuring terminal.
TP9501 (A-3) :
++
+3.3 V check terminal
++
+3.3 V measuring terminal.
TP9001 (A-4) :
++
+1.8 V-1 check terminal
++
+1.8 V-1 measuring terminal.
TP9301 (A-4) :
++
+1.8 V-2 check terminal
++
+1.8 V-2 measuring terminal.
TP400 (C-8) : System clock signal check terminal
Use this terminal to check the system clock signal supplied
from CPU module.
MVS-8000SF
TP205 (L-12) : VCLK (clock for video signal)
signal check terminal
Use this terminal to check the clock for video signal.
<LED on the CPU DR module> (C11)
Refer to < LED on the CPU DR module > in “1. CA-44
Board”.
<Switch on the CPU DR module> (C11)
Refer to < Switch on the CPU DR module > in “1. CA-44
Board”.
1-55
Page 64
1-8. Checks on Completion of Installation
12. CNI-9 board (Suffix : -12) (MKS-8110HD)
AB CDE FGHJ K L
1
2
3
4
S101
S201
S301
S401
S501
S601
S701
S801
S901
S1001
S1101
S1201
S1301 S1401
CNI-9 board A side/Component side
<Switch>
S101 (A-3), S201, S301 (B-3), S401, S501 (C-3), S601 (D-3), S701, S801 (E-3), S901 (F-3),
S1001, S1101 (G-3), S1201 (H-3), S1301, S1401 (J-3), S1501, S1601 (K-3), S1701 (L-3) :
Output band-width compensation switch
They are the output band-width compensation ON/OFF switches.
Use these switches in the factory setting positions.
Factory setting
S101 to S1701 : All OFF
S1501
S1601
S1701
1-56
MVS-8000SF
Page 65
1-8. Checks on Completion of Installation
1-8-2. Checks on the Switch Setting the Number of Power Supply Units
Before turning on the power of the MVS-8000SF, confirm that the switch S303 on the CA-44 board is set
in the following position (default setting).
S303 (B-1)/CA-44 board : Switch setting the number of power supply units (DIP type)
S303-1 : OFF
S303-2 : OFF
S303-3 : ON
S303-4 : OFF
AB C D E
1
S303
G
F
E
D
C
B
A
2
654321
12345
F
E
D
C
CPU-DK
B
Module
A
(COM CPU-1)
CPU-DR
Module
3
4
(MAIN CPU)
IF-844
5
(S-BUS)
12345
F
E
D
C
CPU-DK
B
Module
A
(COM CPU-2)
AB
1
A
2
B
3
12
SG-272
MVS-8000SF
1-57
Page 66
1-9. System Connection
1-9. System Connection
Configure the MVS-8000 system connections referring to the connection example as shown below.
1. Connection example
Reference
video signal
Ethernet switchEthernet switch
*b
DATA CTRL REMOTE 1
Reference video signal
*a*a
Reference
video signal
*b
DATA LAN
REMOTE
*b
BKS-R series
CTRL EDITOR
Editing Control System
CTRL
DATA
DME Processor Pack
MVE-8000
BVE-9100
PERIPH
System Control Unit
MKS-8010
HDS-X series
Switcher Processor Pack
MVS8000SF-C
Device Control Unit Pack DCU-8000
PERIPH
VTR DDR
*a : Connect each LAN (CTRL, DATA) to the separate Ethernet switches respectively.
However, a single Ethernet switch can be used for connecting each LAN.
*b : Terminate the system with the 75 Z terminators supplied. The 75 Z terminators are supplied with the equipment.
1-58
Reference
video signal
Audio mixer
Crossover cable
BNC cable
*b
MVS-8000SF
Page 67
2. Flow of Video Signals
1-9. System Connection
DME Processor Pack
MVE-8000
Camera
VTR
Routing Switcher
MONITOR
SWITCHER B
DME 1B
PRIMARY INPUTS
1 to 34
Switcher Processor Pack
MVS8000SF-C
Reference video
signal
Reference video
signal
*c
*c
OUTPUTS
1 to 16
SWITCHER A
AC100 to 240 V Power Supply
AC100 to 240 V Power Supply
DME 1A
*a
*b
AC100 to 240 V Power Supply
AC100 to 240 V Power Supply
AC100 to 240 V Power Supply
*b
*b
*b
VTR
68-pin Cable
Video Signal Input
Video Signal Output
Video/Key Signal
AC Power Supply
*a : For the AC power cord, refer to “Optional Items” of the “DME Processor Pack MVE-8000” Operation Manual.
*b : For the AC power cord, refer to “Optional Items” of the “Multi-Format Switcher Processor MVS-8000”
Operation Manual (15 page).
*c : Terminate the system with the 75 Z terminators supplied with this unit.
MVS-8000SF
1-59
Page 68
Page 69
2-1. Troubleshooting
A picture is not displayed
on the monitor screen even
though the main power of
the MVS-8000SF is turned
on.
Are the standard boards
installed into the specified
slots?
Install the standard boards
into the specified slots.
(Refer to MVS-8000SF
Maintenance Manual.)
Are the option boards
installed into the specified
slots?
Are the input and output
cables connected correctly?
Install the option boards into
the specified slots.
(Refer to Section 1-4.)
YES
Is the Software installed
correctly?
YES
The MVS-8000SF is
probably defective.
YES
NO
NO
Install the software correctly.
(Refer to the Use s Guide.)
NO
Check connections of the
input and output equipment.
NO
YES
Section 2
Service Overview
The main power of the MVS-8000 cannot be
turned on. (Indicator does not light green.)
The main power of the
MVS-8000SF cannot be
turned on. (Indicator does
not light green.)
Are two or more power
switches of the MVS-8000SF
turned on?
YES
Is the power cord of the
MVS-8000SF connected
correctly?
YES
The power supply unit is
probably defective.
Set two or more power
NO
switches of the MVS-8000SF
to on.
NO
Connect it correctly.
The monitor picture is not displayed correctly.
MVS-8000SF
2-1
Page 70
2-2. Periodic Inspection and Maintenance 2-3. About the Data Backup Capacitor
2-2.
Periodic Inspection and Maintenance
2-2-1. Cleaning
1. Front panel
The filter on the rear of the front panel can easily accumulate the dust. Be sure to remove dust by cleaning as
follows.
(1) Remove the front panel. (Refer to Section 1-4-1.)
(2) Remove the dust accumulated on the filter with a
vacuum cleaner.
n
Cleaning the filter by washing in water is recommended when there is a heavy accumulation of dust.
Be sure to dry the filter completely after it has been
washed.
Front panel
2. Fan
MVS-8000SF is air-cooled by the fans (on both sides).
If dust has accumulated in the intake of the fan, air is
prevented from flowing smoothly and this may result in a
temperature rise inside the machine. This may have an
adverse effect on performance and the life of the machine.
Cleaning of the fan every month is recommended.
Contact your local Sony Sales Office/Service Center for
information on cleaning the fan.
Fan
Fans
Filter
Fans
Fan
2-3. About the Data Backup Capacitor
A large capacitor is installed on the CA-44 board in order
to backup the memory storing the setup and other data in
the MVS-8000SF.
Leave the main power of the MVS-8000SF turned on for
one hour or longer in order to charge the large capacitor.
The data can be backed up for about one week when the
capacitor is fully charged under the normal operating
temperature.
2-2
MVS-8000SF
Page 71
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
MVS-8000SF
Page 72
MVS8000SF-C (SY) E
3-620-565-03
Printed in Japan
Sony Corporation 2003. 3 16
B&P Company ©2002
Loading...