Sony MVS-8000A-C, MVS8000AS-C, MVS-8000A, MVS-8000ASF Installation Manual
SWITCHER PROCESSOR PACK
MVS-8000A-C
MVS8000AS-C
MULTI FORMAT SWITCHER PROCESSOR
MVS-8000A
MVS-8000ASF
HK-PSU04
MKS-8160A
MKS-8162A
MKS-8210A
MKS-8440A
MKS-8110M
MKS-8111M
MKS-8161M
MKS-8170M
MKS-8420M
BZS-8250
INSTALLATION MANUAL
1st Edition (Revised 1)
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
MVS-8000A Serial No. 10001 and Higher
MVS8000ASF Serial No. 10001 and Higher
HK-PSU04 Serial No. 10001 and Higher
MKS-8160A Serial No. 10001 and Higher
MKS-8162A Serial No. 10001 and Higher
MKS-8210A Serial No. 10001 and Higher
MKS-8440A Serial No. 10001 and Higher
MKS-8110M Serial No. 10001 and Higher
MKS-8111M Serial No. 10001 and Higher
MKS-8161M Serial No. 10001 and Higher
MKS-8170M Serial No. 10001 and Higher
MKS-8420M Serial No. 10001 and Higher
BZS-8250
MVS-8000A/8000ASF
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.
6. When performing the installation, keep the rear of
the unit 10 cm (4 inches) or more away from walls
in order to obtain proper exhaust and radiation of
heat.
When using a LAN cable:
For safety,do not connect to the connector for
peripheral device wiring that might have excessive
voltage.
MVS-8000A/8000ASF
1 (P)
Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 3
Related manuals ......................................................................................................... 3
Contents ..................................................................................................................... 3
1. Installation
1-1. Operating Environment ...............................................................................1-1
1-2. Power Supply .............................................................................................. 1-1
1-2-1. Power Specifications ..................................................................1-1
1-2-2. Recommended Power Cord ........................................................ 1-1
1-3. Installation Space (External dimensions) .................................................... 1-2
1-3-1. MVS-8000A ...............................................................................1-2
1-3-2. MVS-8000ASF ..........................................................................1-3
1-4. Installing the Options .................................................................................. 1-4
1-4-1. Installing the Plug-in Boards ...................................................... 1-4
1-4-2. Installing the Connector Board ..................................................1-6
1-4-3. Installing the HK-PSU04 ...........................................................1-9
1-4-4. Installing the BZS-8250 ............................................................. 1-9
1-5. Rack Mounting .......................................................................................... 1-10
1-6. Matching Connectors ................................................................................ 1-12
1-7. Input/Output Signals of Connectors .......................................................... 1-13
1-8. Checks on Completion of Installation ....................................................... 1-15
1-8-1. Description of On-board Switches and LEDs ..........................1-15
1-8-2. Checks on the Switch Setting the Number of
Power Supply Units.................................................................. 1-31
1-9. System Connection.................................................................................... 1-32
MVS-8000A/8000ASF
2. Service Overview
2-1. Troubleshooting .......................................................................................... 2-1
2-2. Periodic Inspection and Maintenance ......................................................... 2-2
2-2-1. Cleaning .....................................................................................2-2
2-3. About the Data Backup Capacitor............................................................... 2-3
1
Purpose of this manual
Related manuals
Manual Structure
This manual is the installation manual of Switcher Processor Pack MVS-8000A-C/
MVS8000AS-C and their optional boards and units.
This manual is intended for use by trained system and service engineers, and
describes the information on installing the MVS-8000A-C/MVS8000AS-C system.
The following manuals are prepared for MVS-8000A-C/MVS8000AS-C and their
optional boards and units.
..
. Operation Manual (Supplied with MVS-8000A-C/MVS8000AS-C)
..
This manual describes the application and operation of MVS-8000A-C/
MVS8000AS-C.
..
. System Setup Manual (Available on request)
..
This manual describes the information that is required to connect the MVS-8xxx/
MVE-8000/DCU-8000/CCP-8000 to the MVS-8000 system, and to start up the
system.
If this manual is required, please contact your local Sony Sales Office/Service
Center.
Contents
..
. Maintenance Manual (Available on request)
..
This manual describes the detailed service information.
If this manual is required, please contact your local Sony Sales Office/Service
Center.
..
. “Semiconductor Pin Assignments” CD-ROM (Available on request)
..
This “Semiconductor Pin Assignments” CD-ROM allows you to search for
semiconductors used in B&P Company equipment.
Semiconductors that cannot be searched for on this CD-ROM are listed in the
maintenance manual for the corresponding unit. The maintenance manual contains
a complete list of all semiconductors and their ID Nos., and thus should be used
together with the CD-ROM.
Part number: 9-968-546-XX
This manual is organized by following sections.
Section 1 Installation
This section describes the operating environment, power supply, installation space,
installation of optional boards and units, rack mounting, connectors, input and
output signals of connectors, checking upon completion of installation, and system
configuration.
MVS-8000A/8000ASF
Section 2 Service Overview
This section describes the troubleshooting and periodic inspection and maintenance.
3
Section 1
For customers in the U.S.A. and Canada
1 Power cord, 125 V 10 A (2.4 m) : ! 1-557-377-11
AC inlet
1
Installation
1-1. Operating Environment
Operating guaranteed temperature : +5 dC to +40 dC
Performance guaranteed temperature : +10 dC to +35 dC
Operating humidity : 10 % to 90 %
(relative humidity)
Storage temperature : _20 dC to +60 dC
Mass (when all options are installed) :
MVS-8000A : Approx. 51 kg
MVS-8000ASF : Approx. 28 kg
Prohibited locations for installation
. Areas where the unit will be exposed do direct sunlight
or any other strong lights.
. Dusty areas
. Areas subject to vibration.
. Areas with strong electric or magnetic fields.
. Areas near heat sources.
. Areas subject to electrical noise.
. Areas subject where is subjected to static electricity.
Ventilation
The inside of the MVS-8000A-C/MVS8000AS-C (MVS8000A series hereafter) is cooled by a fan (both sides).
The power supply can be damaged if the exhaust vent
(both sides) and air intake (front panel) are blocked or the
fan is stopped.
Therefore, leave a blank space of more than 10 cm in the
front and both sides of the DVS-9000 series).
m
. As the inrush current at turn-on is a maximum 120 A (at
100 V)/150 A (at 230 V), the capacity of the AC power
source must be commensurate with this load.
If the capacity of the AC power is not adequately large,
the AC power source braker will operate or the unit will
abnormally operate.
. The MVS-8000A contains the two power supply units as
the standard configuration. A maximum of four power
supply units may be installed. When starting up the
MVS-8000A, be sure to turn on the power of two or
more power supply units.
. The MVS-8000ASF contains the single power supply
unit as the standard configuration. A maximum of two
power supply units may be installed. When starting up
the MVS-8000ASF, be sure to turn on the power of one
or more power supply units.
1-2-2. Recommended Power Cord
w
. Use the approved Power Cord (3-core mains lead)/
Appliance Connector/Plug with earthing-contacts that
conforms to the safety regulations of each country if
applicable.
. Use the Power Cord (3-core mains lead)/Appliance
Connector/Plug conforming to the proper ratings (Voltage, Ampere).
If you have questions on the use of the above Power Cord/
Appliance Connector/Plug, please contact your local Sony
Sales Office/Service Center.
1-2. Power Supply
1-2-1. Power Specifications
A switching regulator is used for the power supply of this
unit. The voltage within the range of 100 V to 240 V can
be used without changing the supply voltage.
Power requirements : AC 100 to 240 V ± 10 %
Power frequency : 50/60 Hz
Current consumption (when all options are installed) :
MVS-8000A : 15 to 6.25 A
MVS-8000ASF : 7.5 to 3.1 A
MVS-8000A/8000ASF
c
. Never use an injured power cord.
. Plugging the power cord in the AC inlet, push as far as it
will go.
For customers in the all European countries
1 Power cord, 250 V 10 A (2.4 m) : ! 1-782-929-12
1
AC inlet
1-1
1-3. Installation Space (External dimensions)
1-3-1. MVS-8000A
520
7
482
465
440
375
35
354 (8U)
17.5
144.5 115.5 115.5
61
370
51
Unit : mm
1-2
MVS-8000A/8000ASF
B3
B3
B3
B3
1-3-2. MVS-8000ASF
520
7
482
465
440
375
35
176 (4U)
17.5
144.5 115.5 115.5
61
380
B3
B3
B3
B3
51
Unit : mm
MVS-8000A/8000ASF
1-3
1-4. Installing the Options
1-4-1. Installing the Plug-in Boards
The MVS-8000A-C/MVS8000AS-C is shipped from the
factory with the necessary option boards (refer to the
following table) already installed in accordance with the
specified system configuration.
The following options are available for the MVS-8000A/
8000ASF.
MVS-8000A/8000ASF Option List
Model name Board configuration
Plug-in board
MKS-8160A OUT-28 board CNO-25 board
(MVS-8000A only)
24 Output Board
MKS-8162A CNO-25 board _
(MVS-8000ASF only)
12 Output Connector Board
MKS-8210A MIX-48A board _
Mix/Effect Board
MKS-8440A MY-112B board _
Frame Memory Board
MKS-8170A DIF-141 board _
DME Interface Board
MKS-8420A CC-90 board _
Color Correction Board
MKS-8161M _ CNO-24 board
(MVS-8000A only)
8 Monitor Output Board
MKS-8110M _ CNI-22 board
17 Input Board
MKS-8111M _ CNI-23 board
(MVS-8000A only)
Additional 12 Input Board
HK-PSU04 __
Power Supply Unit
BZS-8250
Simple P/P Software
* : BZS-8250 is the software options.
*
__
Connector board
c
Be sure to turn off the POWER switch before starting
installation work.
If installation work is started with the POWER switch left
on, it may cause electrical shock or damage to printed
circuit boards.
Each plug-in board of the Production Switcher Processor
MVS-8000A/8000ASF is allocated to a specific slot into
which they must be installed. Check to see that the respective plug-in boards are installed in their respective slots.
The name of the board is shown near the eject lever at the
right-most end of each plug-in board.
Names of the plug-in boards and the slot numbers, to
which the plug-in boards are allocated, are shown on the
Extract PWB stopper assembly inside the front panel of the
MVS-8000A/8000ASF. Install the respective plug-in
boards according to this instruction.
m
. Check to see that connectors of the plug-in boards are
securely inserted into the mother board (MVS-8000A :
MB-1014 board, MVS-8000ASF : MB-1034 board)
without loose contact.
If any plug-in board is inserted into the incorrect slot, it
causes a system error and the system will not work
correctly.
. After installing the plug-in board, the software must be
installed. Install the software of V4.20 or later version.
For installing the software, refer to the user’s guide of
the MVS-8000A/8000ASF system.
1-4
MVS-8000A/8000ASF
Installation Procedure
Eject levers
(The illustration shows the MVS-8000A.)
1. Turn off the main power of this unit (MVS-8000A or
MVS-8000ASF) and disconnect the AC power cord
from the wall outlet.
2. Loosen the four screws (with drop-safe) and remove
the front panel to the arrow.
Screw (with
drop-safe)
Screw (with
drop-safe)
4. While the eject levers are opened as shown in the
illustration, insert the plug-in board into the board
guide rail.
Front panel
(The illustration shows the MVS-8000A.)
Screws
(with drop-safe)
3. Remove the fixing screws (MVS-8000A: 6 screws, MVS8000ASF: 4 screws) and remove the Extract PWB
stopper assembly.
B3 x 5
Extract PWB stopper
assembly
B3 x 5
(The illustration shows the MVS-8000A.)
MVS-8000A/8000ASF
1-5
5. While closing the eject levers in the direction of arrow
1, push in the plug-in board.
1-4-2. Installing the Connector Board
1. Remove the two screws and remove the blank panel.
n
Store the removed blank panel in a safe place.
B3 x 5
Blank panel
1
Eject lever Eject lever
(The illustration shows the MVS-8000A.)
1
6. Attach the plug-in board loose-proof assembly and the
front panel by reversing the installation steps of 2, 3.
MVS-8000A option
Name of option Name of board
MKS-8160A OUT-28 board 14
MKS-8210A MIX-48A board 1, 3
MKS-8440A MY-112B board 15, 16
MKS-8170M DIF-141 board 4
MKS-8420M CC-90 board 13
Slot on the front side
MVS-8000ASF option
B3 x 5
(The illustration shows the MVS-8000A.)
Name of option Name of board
MKS-8210A MIX-48A board 1
MKS-8440A MY-112B board 7
MKS-8170M DIF-141 board 2
MKS-8420M CC-90 board 6
1-6
Slot on the front side
MVS-8000A/8000ASF
2. Insert the connector board horizontally level and
secure it with the two fixing screws.
Screws
(with drop-safe)
Connector board
Screws
(with drop-safe)
(The illustration shows the MVS-8000A.)
MVS-8000A option
Name of option Name of board
MKS-8160A CNO-25 board 14, 15
MKS-8161M CNO-24 board 5
MKS-8110M CNI-22 board 9, 10, 11
MKS-8111M CNI-23 board 7
Slot on the rear side
MVS-8000ASF option
Name of option Name of board
MKS-8162A CNO-25 board 6
MKS-8110M CNI-22 board 4
Slot on the rear side
MVS-8000A/8000ASF
1-7
Loading...