Sony MPK-TRV2 Operating manual

Marine Pack

3-859-264-21 (1)

Operating Instructions Mode d’emploi Manual de instrucciones Manual de instruções

F E P

MPK-TRV2

1997 by Sony Corporation

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

English

Table of contents

Features ........................................................................................ 2

Supplied accessories................................................................... 3

Precautions .................................................................................. 4

Labeling the parts and controls ................................................ 5

Position of the adaptor and the remote control cable ........... 6

Notes on the O-ring .................................................................... 8

Attaching the video camera recorder to the marine pack .... 9

Recording................................................................................... 13

When the LEAK lamp flashes................................................. 14

Removing the video camera recorder ................................... 15

Underwater recording ............................................................. 16

Specifications............................................................................. 17

Prerecording checklist.............................................................. 17

Features

The MPK-TRV2 marine pack allows the following 8 mm video camera recorders to be used underwater.

CCD-TR1*/TR1E* CCD-TR3*/TR3E* CCD-TR8*/TR8E* CCD-TR18E* CCD-TR330/TR330E CCD-TR340E CCD-TR401E CCD-TR402E CCD-TR403 CCD-TR410E CCD-TR420/TR420E CCD-TR440/TR440E CCD-TR490/TR490E CCD-TR501E CCD-TR502E CCD-TR503E CCD-TR506/TR506E CCD-TR507 CCD-TR510E CCD-TR520E CCD-TR555/TR555E CCD-TR590/TR590E CCD-TR610E* CCD-TR620E CCD-TR710E* CCD-TR720E CCD-TR740E CCD-TR760E* CCD-TR810E* CCD-TR820E CCD-TR825E CCD-TR910*/TR910E*

CCD-TR920E CCD-TR1100E CCD-TR2200*/TR2200E* CCD-TR2300*/TR2300E* CCD-TR3000*/TR3000E* CCD-TR3100E CCD-TR3300*/TR3300E* CCD-TR3400E CCD-TRV10E CCD-TRV11/TRV11E CCD-TRV12/TRV12E CCD-TRV14E CCD-TRV21/TRV21E CCD-TRV24E CCD-TRV30/TRV30E CCD-TRV31*/TRV31E* CCD-TRV34 CCD-TRV40/TRV40E CCD-TRV41*/TRV41E* CCD-TRV44/TRV44E CCD-TRV51*/TRV51E* CCD-TRV54E CCD-TRV56E CCD-TRV60E CCD-TRV61E* CCD-TRV64E CCD-TRV70/TRV70E CCD-TRV81E* CCD-TRV91*/TRV91E* CCD-TRV94/TRV94E CCD-TRV101/TRV101E

This mark indicates that this product is a genuine accessory for Sony video products. When purchasing Sony video products, Sony recommends that you purchase accessories with this “GENUINE VIDEO ACCESSORIES” mark.

• Recording at a depth of 75 meters (246 feet) is

possible.

• The following operations can be performed

underwater.

Power on/off Auto focusing on/off (Only models marked with *) Recording start/stop Power zooming

If there are specks or dust in focus on the front glass of the marine pack, move the power zoom lever towards the T (telephoto) side slightly so that the zoom indicator inside the viewfinder moves towards T. (See the illustration below.)

Zoom indicator in the viewfinder

We recommend you use a wide-conversion lens (not supplied) when using the marine pack.

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Supplied accessories

Adaptor A (1)

Adaptor B (1)

O-rings (2)

Grease (1)

F E

Adaptor C (1)

Mounting screw plate (1)

Accessory belt (1)

Viewfinder adaptor (1)

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Precautions

On the video camera recorder

Take care not to expose the equipment to salty air. Do not drip water on the equipment.

• Do not open the marine pack while at sea or at the

seaside. Preparations such as installing and checking the equipment should be made in a place with low humidity and no salty air.

• When a video camera recorder is to be used near the sea

for a long time, we recommend that it be checked periodically by a Sony dealer.

• If the equipment becomes wet, take it immediately to the

nearest Sony dealer for preventive maintenance.

On the video camera recorder power source

We recommend you use battery packs with a large capacity. However, in some cases battery packs NP-99/4500/F930 cannot be attached to the video camera recorder.

On the marine pack

• If you open and join the front and rear shells in a place

with high temperature and high humidity, moisture condensation may occur when you put the marine pack in the water, causing the front glass to fog.

• The waterproof integrity of the marine pack is maintained

by the O-ring, and the groove and surface where it touches. Be especially careful not to damage or deform that area.

• Do not leave the marine pack under direct sunlight for a

long period of time, otherwise the temperature in the marine pack may rise and the equipment inside may be damaged.

• If you cannot avoid leaving the marine pack under direct

sunlight, be sure to cover the marine pack with a towel or other protection.

• Do not throw the marine pack into the water. Lower it

gently into the water.

On maintenance

After recording in the sea, submerge the marine pack with the buckles tightly fastened in fresh water for a while to remove the sea water. Then rinse it with fresh water and dry it with a soft cloth.

• Every time you use the marine pack and the video camera

recorder underwater, clean the video camera recorder and the inside of the marine pack with a dry soft cloth. Do not use any type of solvent, such as alcohol or benzine for cleaning, as this may damage the finish.

• When you store the marine pack, grease the O-ring and

put it in the groove correctly. Join the front and rear shells then put in a cool place without fastening the buckles. Avoid storing the marine pack in a hot or very cold place, in a place subject to direct sunlight or excessive dust, or together with naphthalene or camphor as. This will damage the marine pack.

• If water comes between the rear shell and the rubber part,

remove the rubber and clean it with a dry soft cloth.

On transportation

• When transporting the marine pack, be sure to remove

the video camera recorder from the marine pack.

• When transporting the marine pack by air or by car, use a

marine pack carrying case (not supplied).

On recording underwater

• Check that the equipment operates correctly and that

there is no water leak at a depth of about one meter (3 feet) before you dive deeper.

• Be sure to follow the safety rules for diving, such as

diving period and depth.

• Remove the bubbles from the outside of the front glass.

Sony does not accept liability for damage to the video camera recorder, battery, etc. in the marine pack or for the loss of prerecorded material if a water leak caused by incorrect operation occurs.

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Labeling the parts and controls

• For the use of each part or control, see the pages indicated in parenthesis.

Eyecup

Rear shell

Power zoom lever T/W (13)

Grip

START/STOP button (13)

Buckles (11, 12)

Accessory shoes for underwater video lights (16)

Accessory shoe

Front shell

Underwater microphone (monaural)

Front glass

Video cable connector (14)

Lead weight

Video output jack

Remote control cable (10)

Camera mount (10)

O-ring (8)

Microphone cable (10)

AUTO FOCUS ON/OFF button (13)

STANDBY/ LOCK switch (13)

REC LEAK

LEAK lamp (yellow) (14)

REC (recording) lamp (red) (13)

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Position of the adaptor and the remote control cable

The position of the adaptor and the mounting screw plate depend on the video camera model. See the following page when adjusting the adaptor and mounting screw plate position.

Check the position for the video camera recorder you use. Mounting instructions are explained in “Attaching the video camera recorder to the marine pack” on page 9.

Position of the mounting screw plate on the adaptor

Put the mounting screw plate on the number of the adaptor depending upon the model of video camera recorder.

Adaptor A

Mounting screw plate

Adaptor A

To disassemble after using.

Adaptor B

Mounting screw plate

Adaptor B

Attach adaptor C to adaptor B.

Adaptor C

Adaptor B

To detach adaptor C from adaptor B.

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Video camera recorder CCD-

Position of the mounting screw plate on the adaptor

Without a wideconversion lens

With a wideconversion lens

Video camera recorder CCD-

Position of the mounting screw plate on the adaptor

Without a wideconversion lens

With a wideconversion lens

TRV30/TRV40/TRV70 TRV30E/TRV40E/TRV60E/ TRV70E

TR330/TR403/TR420/ TR440/TR490/TR590 TR330E/TR340E/TR401E/ TR402E/TR410E/TR420E/ TR440E/TR490E/TR510E/ TR520E/TR590E

TR1/TR3/TR8 TR1E/TR3E/TR8E/TR18E

TR506/TR507/TR501E/ TR502E/TR503E/TR506E/ TR620E/TR720E/TR740E TRV11/TRV12/TRV21/ TRV34/TRV44/TRV10E/ TRV11E/TRV12E/TRV14E/ TRV21E/TRV24E/TRV44E

TRV94/TRV54E/TRV56E/ TRV94E

TR3000/TR3000E

TR555/TR555E

TRV101/TRV101E

TR910/TR610E/TR710E/ TR760E/TR810E/TR910E

B2 B9

B3 B6 B3 B7

B4 B6

TR2200/TR2300/TR3300/ TR2200E/TR2300E/ TR3100E/TR3300E/ TR3400E/TRV31/TRV41/ TRV51/TRV91/TRV31E/ TRV41E/TRV51E/TRV61E/ TRV81E/TRV91E

TRV64E/TRV820E/ TRV825E/TRV920E

TR1100E

A, B adaptor to be used. 1, 2, 3... corresponding number on the adaptor.

B4 B7

B5 B8

B5 B9

Notes

• The CCD-TRV101/TRV101E video camera recorders cannot be fitted with a wide conversion lens.

• When you attach a wide conversion lens to the CCD-TR820E/TR825E/TR1100E/TR2200/TR2200E/TR3100E/TRV10E/ TRV11/TRV11E/TRV12/TRV12E/TRV21/TRV21E/TRV31/TRV31E/TRV41/TRV41E/TRV51/TRV51E/TRV61E/ TRV81E/TRV91/TRV91E video camera recorders, you cannot attach the viewfinder adaptor.

• When you attach a wide conversion lens to the CCD-TRV10E/TRV11/TRV11E/TRV12/TRV12E/TRV21/TRV21E video camera recorders, you cannot attach Sony battery NP-99/4500.

• When you attach a wide conversion lens to the CCD-TR1100E/TR2200/TR2200E/TR2300/TR2300E/TR3100E/TR3300/ TR3300E/TR3400E video camera recorders, you cannot attach Sony battery NP-F930.

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Notes on the O-ring

The O-ring assures the waterproof function of the marine pack. To maintain waterproof integrity, use it correctly. Incorrect handling may cause water to leak in.

O-ring

Front shell Rear shell

Check that there are no scratches or cracks.

Scratches or cracks on the O-ring may cause water to leak in. If the O-ring is damaged in this way, replace it with a new one. Do not remove the O-ring from the groove with a metal tool or a tool with a sharp point.

Crack

Scratches

Grease the O-ring

The grease protects the O-ring from wear. Check that there are no cracks or dust on the O-ring, then grease it using your finger. While greasing, double check that there are no cracks or dust. Never use cloth or paper to apply grease because the fibers may cling. Do not use any type of grease other then the supplied one, or it may damage the O-ring. If you run out of silicone grease (2-115-921-01) you can purchase it from your nearest Sony Service Center.

Do not twist the O-ring.

Put the O-ring in the groove evenly. Never twist it.

Not this way

Do not pinch the O-ring with the marine pack.

Remove any dust, sand or hair from the O-ring.

Make sure there is no dust, sand or hair on the O-ring, in the groove, or on the surface of the marine pack where the O-ring touches. If there is, clean it completely, or the Oring and the surface of the marine pack may be damaged and water may leak in.

Dust

Surface of the marine pack where the O-ring touches

O-ring groove

Hair

Sand

When joining the front and rear shells, take care not to pinch the O-ring between them shells. If this happens, not only will the O-ring be damaged, but water may leak in.

Storage

Put the supplied spare O-rings in the original carton and store it in a cool place.

• Do not expose the O-ring to direct sunlight.

• Do not place a heavy object on the O-ring.

• Do not fold the O-ring.

Useful life of the O-ring.

Depending upon maintenance and the length of use, we recommend changing the O-ring every one or two years. The O-ring (3-952-928-01) can be replaced at your nearest Sony Service Center.

O-ring

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Attaching the video camera recorder to the marine pack

Remove the lens cap, shoulder strap, filter, etc.,

from the video camera recorder.

Attach the wide conversion lens (not supplied).

By attaching the wide conversion lens, the shooting coverage becomes wider, and the subject size becomes smaller.

When using adaptor A, attach it to the video

camera recorder.

Check that the position of the mounting screw plate is correct. (See pages 6 and 7.) When using adaptor B, skip this step.

Attach a charged battery pack and insert a video

cassette.

Attach the Viewfinder adaptor.

If the viewfinder adaptor is loose when it is attached, bend the eyecup of the camcorder and attach it again.

Adjust the video camera recorder.

Refer to the operation manual of your video camera recorder.

Set the POWER

switch to CAMERA.

CAMERA

The following adjustments are needed when your video camera recorder has the corresponding function. Refer to the operation manual of the video camera recorder for details.

White balance

Shutter speed Program AE Brightness

Normally set to w (outdoor). Set to e (indoor) for night diving.

Set where no indicator appears. Set where no indicator appears. Turn off the indicator.

Set the STANDBY

switch to STANDBY.

On some video camera recorder models, you cannot adjust the focus with the button on the marine pack. Set the focus to auto focus mode (see page 2).

(continued)

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Attaching the video camera recorder to the marine pack

Attach the video camera recorder to the marine pack.

Check the position of the adaptor. (See pages 6 and 7.)

When using adaptor A

Connect the remote control cable to

l REMOTE.

Connect the microphone cable to MIC. (The sound is recorded in monaural.)

Slide the video camera

recorder into the marine pack until the hooks of the camera mount catch the adaptor.

Fasten the screw.

When using adaptor B

Align the right side of the

adaptor with the hooks of the camera mount, then push down the adaptor.

adaptor B

Fasten the screw.

Screwdriver

Camera mount

Connect the microphone cable to MIC

jack of the video camera recorder. (The sound is recorded in monaural.)

Attach the video camera recorder

to the adaptor.

Connect the remote control cable to the

l REMOTE jack of the video camera recorder.

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Raise the buckles until they stop.

Buckles

Fasten the video camera recorder with the

accessory belt.

When you fasten the video camera recorder with accessory belt, take care not to touch the zoom button.

O-ring

Check the O-ring and grease it slightly.

Accessory belt

(continued)

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Attaching the video camera recorder to the marine pack

Attach the front shell to the rear shell.

Put the front shell on the rear

shell.

Press the top of both grips

firmly.

Align here as shown in the illustration.

Lower both buckles at the

same time until they are locked. You will hear a click.

Now you are ready for underwater recording.

Set the STANDBY/LOCK switch of the marine pack to LOCK. If you set it to STANDBY, the battery may be used up before recording.

Note

When the viewfinder adaptor is attached to the viewfinder of your camcorder, you get a wide view of what appears in the viewfinder screen. However, when viewed from an angle, the screen may appear distorted.

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Recording

REC LEAK

Check that the equipment operates correctly and that there is no water leak at a depth of about one meter (3 feet) before you dive deeper.

Set the STANDBY/LOCK switch to

STANDBY.

The REC lamp (red) lights up during recording.

AUTO FOCUS ON/OFF button

Power zoom lever

Press START/STOP button to start recording.

To zoom

Slide the power zoom lever towards T for telephoto (subject appears closer) or W for wide-angle (subject appears farther away). The zooming speed can be changed on some video camera recorder models from a slow speed to faster by sliding the zooming lever a little more.

Wide-angle Telephoto

When you set the power zoom lever to the full wideangle position (macro), specks or bubbles on the front glass may come into focus. In this case, slide the power zoom lever a little towards T and return towards W.

To keep a subject in focus

After you focus on a subject, press the AUTO FOCUS ON/ OFF button to set the video camera recorder to manual focus mode. Even if fish swim between the video camera recorder and the subject, you can still keep the subject in focus.

Note On some video camera recorder models, the AUTO FOCUS ON/OFF button is not operative. Set the video camera recorder to auto focus mode (see page 2).

To stop recording

Press the START/STOP button.

(continued)

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Recording

To attach/detach the lid of the video cable connector

A video cable connector is provided so that video equipment can be connected to the marine pack in the future.

Note

Do not remove the lid underwater.

When you reattach the lid, grease the O-ring of the lid before inserting it into the connector.

To detach To attach

O-ring

While

pull out.

While pressing here,

press in.

pressing here,

When the LEAK lamp flashes

If water happens to leak in, the LEAK lamp (yellow) flashes.

In such a case, remove the marine pack from the water as soon as possible, keeping it horizontal. Be sure to surface following the safety rules for diving. Dry the marine pack with a soft cloth and then open it. To switch off the lamp, disconnect the remote control cable. Check the cause of the leak.

If the video camera recorder is wet, take it to the nearest Sony dealer immediately.

REC LEAK

LEAK lamp (yellow)

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Removing the video camera recorder

Before opening the marine pack, rinse it with fresh water and dry with a soft cloth.

Note

When you open the marine pack, follow this procedure to prevent the video camera recorder from getting wet.

Remove the accessories.

Open the marine pack.

Before opening the marine pack, rinse it with

fresh water and dry with a soft cloth.

Unfasten both buckles and remove the front

shell.

• Dry the marine pack well.

• Wipe off any water between the front and rear shells with

a towel.

• Make sure you are dry. Take care that no water drips

from your wet suit.

Insert the remote control plug and the microphone

plug where they were.

Microphone plug

Remote control plug

Take the video camera recorder out of the front

shell.

Remove the

viewfinder adaptor.

Disconnect the remote

control cable.

Disconnect the

microphone cable.

Remove the adaptor.

Adaptor A

Adaptor B

Unfasten the

screw.

Detach the video

camera recorder.

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Underwater recording

Recording underwater is different from recording on land because it is affected by the clarity, depth of the water and the light conditions. The following are hints for good recording underwater.

Color characteristics underwater

Water absorbs light, especially red light, so that objects in deep water are seen as bluish. The color of objects is affected by the clarity of the water.

Best time for recording

The best recording time is from 10:00 a.m. to 2:00 p.m. When the sun its highest, optimum results can be obtained.

Subject size underwater

Since the refractive index underwater is higher than that in air, an object appears 1/4 more closer, and therefore larger. This phenomenon affects the lens on the video camera recorder as well as the human eye. Using a wide- conversion lens (not supplied) is recommended.

Camera work In slow and stable motion

Underwater video light

In deep water or under rocks where direct sunlight does not reach, recording with an underwater video light is recommended. To record at night, use a powerful underwater video light.

Underwater video light such as Sony HVL-M20/ ML20/80DA (not supplied)

When recording, keep your body stable. An unstable shot will be magnified on the TV screen. Move the video camera recording as slowly as possible. As most of the object underwater move, you can record a good programme without moving the video camera recorder.

Attachable to the left and right shoes

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Specifications

Prer ecording checklist

Compatible video camera recorder

See page 2.

Material Aluminum alloy, glass, plastic, lead Waterproofing O-ring, 2 buckles Usable depth Up to 75 meters (246 feet) Underwater microphone

Condenser microphone (monaural)

Controllable function

Power on/off, recording start/stop, auto focus on/off, power zooming

Dimensions

327 mm (127/8 in.)337 mm (133/8 in.)

Mass Approx. 8 kg (17 lb 10 oz) Supplied accessories

Adaptor A (1)/B (1)/C (1) Mounting screw plate (1) O-rings (2) Grease (1) Accessory belt (1) Viewfinder adaptor (1)

Recommended accessories

Underwater video light HVL-M20, HVL-

ML20, HVL-80DA

Carrying case LCH-M40

To make sure that you do not miss shooting opportunities, go over the following checklist.

Item

Battery pack Video cassette

201 mm (8 in.)

Microphone cable, remote control cable

Video camera recorder

O-ring

Buckles

Checkpoints

• Fully charged.

• A cassette is inserted.

• Tape length will cover the

planned recording time.

• The tape is wound to the point

where recording is to begin.

• The safety tab on the cassette is in

the correct position. (The window is not red.)

• Firmly connected to the

respective jacks of the video camera recorder (p. 10).

• Set POWER to CAMERA (p. 9).

• Set STANDBY/LOCK to

STANDBY (p. 9).

• No scratches or cracks.

• No dust, sand or hair around it.

• Correctly set in the groove (p. 8).

• Correctly fastened (p. 12).

Design and specifications are subject to change without notice.

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Français

Tables des matières

Caractéristiques .......................................................................... 2

Accessoires fournis ..................................................................... 3

Précautions .................................................................................. 4

Nomenclature.............................................................................. 5

Position de l’adaptateur et du câble de télécommande ........ 6

Remarques sur le joint torique.................................................. 8

Fixation du camescope dans le Marine Pack .......................... 9

Enregistrement .......................................................................... 13

Si le témoin LEAK clignote ..................................................... 14

Retrait du camescope ............................................................... 15

Enregistrement sous-marin ..................................................... 16

Spécifications............................................................................. 17

Liste des vérifications avant enregistrement ........................ 17

Caractéristiques

Le Marine Pack MPK-TRV2 permet d’utiliser dans l’eau les camescopes 8 mm suivants.

Ce logo indique qu’il s’agit d’un accessoire d’origine pour les produits vidéo Sony. Quand vous achetez des produits vidéo Sony, Sony vous recommande les accessoires portant le logo “GENUINE VIDEO ACCESSORIES”.

• Un enregistrement à une profondeur de 75 mètres

(246 pieds) est possible.

• Les fonctions suivantes sont utilisables sous l’eau.

Mise sous/hors tension Mise en/hors service de l’autofocus (modèles signalés par un* seulement) Marche/arrêt d’enregistrement Zoom électrique

Si de la poussière ou des taches apparaissent sur la vitre avant du Marine Pack, pousser légèrement le levier du zoom électrique vers “T” (téléphoto) pour que le témoin à l’intérieur du viseur se déplace vers “T”. (Voir l’illustration ci-dessous.)

Témoin de zoom dans le viseur.

Lorsque vous utilisez le Marine pack, nous vous conseillons d’utiliser un convertisseur grand angle (non fourni).

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Accessoires fournis

Adaptateur A (1)

Adaptateur B (1)

Joints toriques (2)

Graisse (1)

F E

Adaptateur C (1)

Plaque de montage (1)

Sangle à accessoires (1)

Adaptateur de viseur (1)

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Précautions

A propos du camescope

Veiller à ne pas exposer le camescope aux embruns marins et à ne pas le mouiller.

• Eviter d’ouvrir le Marine Pack en mer ou sur une plage.

Les préparatifs, tels que la mise en place et la vérification de l’appareil, doivent être effectués dans un endroit sec et à l’abri de l’air marin.

• Si le camescope doit être utilisé en mer pendant

longtemps, il est conseillé de le faire vérifier régulièrement par un revendeur Sony.

• Si le camescope a été mouillé, l’emporter immédiatement

chez le revendeur Sony pour le faire contrôler.

Source d’alimentation du camescope

Nous vous conseillons d’utiliser des batteries rechargeables ayant une grande capacité. Cependant avec certains camescopes, les batteries rechargeables NP-99/4500/F930 ne peuvent pas être utilisées.

A propos du Marine Pack

• Si le Marine Pack est plongé dans l’eau après avoir été

ouvert et scellé dans un endroit très chaud et très humide, une condensation d’eau risque de se produire qui peut embuer le verre.

• L’étanchéité du Marine Pack dépend du joint torique ainsi

que de la rainure et de la surface avec lesquels il est en contact. Veiller tout particulièrement à ne pas endommager ou déformer ces pièces.

• Ne pas laisser le Marine Pack en plein soleil pendant une

durée prelongée, car l’élévation de la température interne peut endommager le camescope qui se trouve à l’intérieur.

• Si le Marine Pack doit être laissé en plein soleil, prendre

soin de le recouvrir d’une serviette ou autre.

• Ne pas jeter le Marine Pack dans l’eau, mais l’immerger

avec précaution.

Entretien

Après avoir filmé sous l’eau, plonger le Marine Pack, toutes boucles fermées, pendant un certain temps dans de l’eau douce. Le rincer ensuite à l’eau douce, puis le sécher avec un chiffon sec.

• Chaque fois que le Marine Pack est utilisé avec le

camescope sous l’eau, nettoyer le camescope et l’intérieur du Marine Pack avec un chiffon doux et sec. Ne pas utiliser de solvants, tels que l’alcool ou la benzine, pour ne abîmer la finition.

• Avant de ranger le Marine Pack, graisser les joints

toriques puis les insérer comme il faut dans les rainures. Fermer le Marine Pack et le mettre dans un endroit frais sans serrer les boucles. Eviter d’entreposer le Marine Pack dans un endroit très chaud ou froid, en plein soleil, dans un endroit poussiéreux ou avec de la naphtaline ou du camphre, car il pourrait être endommagé.

• Si de l’eau rentre entre la partie arrière et la partie en

caoutchouc, enlever le caoutchouc et le nettoyer avec un chiffon doux.

Transport

• Avant de transporter le Marine Pack, en retirer le

camescope.

• Pour transporter le Marine Pack en avion ou en voiture,

utiliser une valise de transport (non fournie).

Enregistrement sous-marin

• Avant la plongée, il est conseillé de vérifier que l’appareil

fonctionne et que l’eau ne s’infiltre pas à l’intérieur à un mètre de profondeur (trois pieds).

• Respecter strictement les règles de plongée, notamment

en ce qui concerne la durée et la profondeur.

• Avant un enregistrement, enlever les bulles sur l’extérieur

du verre avant.

Sony décline toute responsabilité pour les dégâts que le camescope, la batterie et les autres composants du Marine Pack ainsi que le matériel enregistré peuvent avoir subis suite à une infiltration d’eau provenant d’une utilisation inadéquate.

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

Nomenclature

• Pour l’utilisation de chaque élément ou commande, voir les pages indiquées entre parenthèses.

Oeilleton

Partie arrière

Levier de zoom électrique T/W (13)

Poignée

Boucles (11, 12)

Touche de marche/arrêt (START/STOP) (13)

Griffe porte-accessoires pour torche vidéo sousmarine (16)

Griffe porte-accessoires

Partie avant

Microphone sous-marin (monophonique)

Verre avant

Connecteur de câble vidéo (14)

Plomb

Prise de sortie vidéo

Monture du camescope (10)

Câble de télécommande (10)

Joint torique (8)

Câble de microphone (10)

Touche de mise en/hors service de l’autofocus (AUTO FOCUS ON/OFF) (13)

Commutateur d’attente/verrouillage (STANDBY/LOCK) (13)

REC LEAK

Témoin d’infiltration (jaune) (LEAK) (14)

Témoin d’enregistrement (rouge) (REC) (13)

Sony MPK-TRV2 (EN,F,E,P) 3-859-264-2X

+ 47 hidden pages