SONY KV-XS29M80, KV-XS29M97 Service Manual

BG-3S
CHASSIS
MODEL COMMANDER DEST. CHASSIS NO.
KV-XS29M80 RM-954 E SCC-U13L-A KV-XS29M97 RM-953 Hong Kong SCC-U17L-A
MODEL COMMANDER DEST. CHASSIS NO.
(RM-953) (RM-954)
TRINITRON
®
COLOR TV
KV-XS29M80/XS29M97
RM-954 RM-953
Power requirements 110-240 V AC, 50/60 Hz Power consumption (W) Indicated on the rear of the TV Television system B/G, I, D/K, M Color system PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58 Channel coverage
B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41 I UHF: B21 to B68 / CATV: S01 to S03, S1 to S41 D/K VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60
M VHF: A2 to A13 / UHF: A14 to A79 /
˘ (Antenna) 75-ohm external terminal Audio output 8W + 8W Number of terminal
D (Video) Input: 3 Output: 1 Phono jacks; 1 VP-P, 75 ohms (Audio) Input: 3 Output: 1 Phono jacks; 1 VP-P, 500 mVrms
(S Video) Input: 2 Y : 1 Vp-p, 75 ohms,
2 (Headphone) Output: 1 Minijack
Picture tube 29 inch
Tube size (cm) 72 Measured diagonally Screen size (cm) 68 Measured diagonally
Dimension (w/h/d, mm) 794 × 573 × 517 Mass (kg) 50
SPECIFICATIONS
(KV-XS29M80)
Note
CATV: S01 to S03, S1 to S41, Z1 to Z39
CATV: A-8 to A-2, A to W+4, W+6 to W+84
unbalanced, sync negative
C : 0.286 Vp-p, 75 ohms
CAUTION
SHOR T CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE MET AL CHASSIS, CR T SHIELD , OR CARBON P AINTED ON THE CR T, AFTER REMO VING THE ANODE.
Design and specifications are subject to change without notice.
SAFETY-RELA TED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE SCHEMA TIC DIA GRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERA TION. REPLA CE THESE COMPONENTS WITH SONY P ARTS WHOSE P ART NUMBERS APPEAR AS SHO WN IN THIS MANU AL OR IN SUPPLEMENTS PUBLISHED BY SONY .
– 2 –
KV-XS29M80/XS29M97
SPECIFICATIONS
(KV-XS29M97)
Power requirements 220-240 V AC, 50/60 Hz Power consumption (W) Indicated on the rear of the TV Television system B/G, I, D/K, M Color system PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58 Stereo system NICAM Stereo B/G, I; A2 Stereo (German) B/G Channel coverage
B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41 I UHF: B21 to B68 / CATV: S01 to S03, S1 to S41 D/K VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60
CATV: S01 to S03, S1 to S41, Z1 to Z39
M VHF: A2 to A13 / UHF: A14 to A79 /
CATV: A-8 to A-2, A to W+4, W+6 to W+84
˘ (Antenna) 75-ohm external terminal Audio output 6W + 6W 10% Distortion 3D WOOFER 15W Number of terminal
D (Video) Input: 4 Output: 1 Phono jacks; 1 VP-P, 75 ohms (Audio) Input: 4 Output: 1 Phono jacks; 500 mVrms
(S Video) Input: 2 Y : 1 Vp-p, 75 ohms,
unbalanced, sync negative
C : 0.286 Vp-p, 75 ohms
(Component Input: 1 Phono jacks:
Video) Y : 1.0 Vp-p, 75 ohms,
sync negative
C
B : 0.7 Vp-p, 75 ohms
CR : 0.7 Vp-p, 75 ohms Audio : 500 mVrms
2 (Headphone) Output: 1 Minijack
Picture tube 29 inch
Tube size (cm) 72 Measured diagonally Screen size (cm) 68 Measured diagonally
Dimension (w/h/d, mm) 794 × 589 × 517 Mass (kg) 54
Note
RM-954 RM-953
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
– 3 –
KV-XS29M80/XS29M97
RM-954 RM-953
TABLE OF CONTENTS
Section Title Page
SELF DIAGNOSIS FUNCTION................................ 5
1. GENERAL ........................................................................ 9
2. DISASSEMBLY
2-1. 3D Speaker Box Removal ....................................... 40
2-2. Rear Cover Removal................................................ 40
2-3. Speaker Removal ..................................................... 40
2-4. Chassis Assy Removal ............................................. 40
2-5. F Bracket Removal .................................................. 41
2-6. Service Position ....................................................... 41
2-7. Replacement of Parts ............................................... 41
2-7-1. Replacement of Control Button ..................................... 41
2-7-2. Replacement of Light Guide .......................................... 41
2-8. D3 Board Removal .................................................. 42
2-9. PWB Holder Removal ............................................. 42
2-10. Terminal Bracket Removal...................................... 42
2-11. P2, B5 and B7 Boards Removal .............................. 42
2-12. H5 Board Removal .................................................. 43
2-13. A and B3 Boards Removal ...................................... 43
2-14. Picture Tube Removal.............................................. 43
3. SET-UP ADJUSTMENTS
3-1. Beam Landing .......................................................... 45
3-2. Convergence............................................................. 46
3-3. Focus Adjustment .................................................... 47
3-4. G2 (Screen) and White Balance Adjustments......... 48
Section Title Page
5. DIAGRAMS
5-1. Block Diagram ......................................................... 59
5-2. Frame Schematic Diagram ...................................... 63
5-3 Circuit Boards Location .......................................... 67
5-4. Schematic Diagrams and Printed Wiring Boards ... 68
(1) Schematic Diagram of A (1/2) Board...................... 71
(2) Schematic Diagram of A (2/2) Board...................... 75
(3) Schematic Diagram of B3 Board ............................ 79
(4) Schematic Diagrams of B5 and B7 Boards............. 83
(5) Schematic Diagram of C Board .............................. 87
(6) Schematic Diagram of P2 Board ............................. 91
(7) Schematic Diagram of D3 Board ............................ 94
(8) Schematic Diagram of H5 Board ............................ 97
(9) Schematic Diagram of VM1 Board........................ 101
(10) Schematic Diagram of F Board.............................. 103
(11) Schematic Diagram of J4 Board............................. 104
5-5. Semiconductors....................................................... 106
6. EXPLODED VIEWS
6-1. Speaker Bracket ...................................................... 109
6-2. Chassis .................................................................... 110
6-3. Picture Tube ............................................................ 111
6-4. 3D Speaker.............................................................. 112
7. ELECTRICAL PARTS LIST...................................... 113
4. CIRCUIT ADJUSTMENT
4-1. Adjustments with Commander ................................ 49
4-2. Adjustment Method ................................................. 50
4-3. Picture Quality Adjustments.................................... 55
4-4. A Board Adjustment After IC003 (Memory)
Replacement............................................................. 55
4-5. Picture Distortion Adjustment................................. 56
– 4 –
KV-XS29M80/XS29M97
RM-954 RM-953
SELF DIAGNOSTIC FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICAT ORS
When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.
Diagnostic
Item
Description
• Power does not turn on
• +B overcurrent (OCP) or overvoltage (OVP)
• Vertical deflection stopped
• Horizontal deflection overdrive
• White balance failure (no PICTURE)
• Micro reset
No. of times
STANDBY/TIMER
lamp flashes
Does not light
2 times
5 times
Self-diagnostic
display/Diagnostic
result
002:000 or 002:001~255 003:001~255 004:001~255
at the same time
005:000 or 005:001~225
101:00 or
101:001~225
Probable
Cause
Location
• Power cord is not plugged in.
• Fuse is burned out F4601 (F)
• H.OUT Q511 is shorted. (A board)
• IC701 is shorted. (C board)
• -13V is not supplied. (A board)
• IC 503 faulty (A board)
• G2 is improperly adjusted. (Note 2)
• CRT problem.
• Video OUT IC701 is faulty. (C board)
• IC301 is faulty. (A board)
• No connection A board to C board.
• Discharge CRT (C Board)
• Static discharge
• External noise
Detected
Symptoms
• Power does not come on.
• No power is supplied to the TV.
• AC power supply is faulty.
• Power does not come on.
• Load on power line is shorted.
• Has entered standby state after horizontal raster.
• Vertical deflection pulse is stopped.
• Power line is shorted or power supply is stopped.
• No raster is generated.
• CRT cathode current detection reference pulse output is small.
• Power is shut down shortly, after this return back to normal.
• Detect Micro latch up.
Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.
The symptom that is diagnosed first by the microcontroller is displayed on the screen.
Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.
– 5 –
KV-XS29M80/XS29M97
RM-954 RM-953
2. DISPLA Y OF STANDBY/TIMER LIGHT FLASH COUNT
2 times
5 times
Lamp ON 0.3 sec. Lamp OFF 0.3 sec.
Lamp OFF 3 sec.
STANDBY/SLEEP lamp
Diagnostic Item Flash Count* +B overcurrent/overvoltage 2 times Vertical deflection stopped
White balance failure 5 times * One flash count is not used for self-diagnostic.
3. STOPPING THE STANDBY/TIMER FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp from flashing.
– 6 –
KV-XS29M80/XS29M97
RM-954 RM-953
4. SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as power sometimes shuts off or screen sometimes goes out that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screendisplay] / channel [5] / Sound volume [-] / Power ON
˘
Note that this differs from entering the service mode (mode volume [+]).
Self-Diagnosis screen display
SELF DIAGNOSTIC
002 : 000 003 : 000 004 : 000 005 : 001
101 : 000
Numeral "0" means that no fault has been detected.
Numeral "1" means a fault has been detected.
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic screen is being displayed.
Channel [8] / 0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
– 7 –
KV-XS29M80/XS29M97
RM-954 RM-953
6. SELF-DIAGNOSTIC CIRCUIT
FROM
CRT
FROM
[+B] Q604 C
[V] Q509/507
IC301
Y/CHROMA JUNGLE
IK-IN
MP/
18 51
PROTECT
SDA
4635
IC001
SYSTEM
IO-8DAT
O-LED
IO-SDAT
MEMORY
B-DAT
54521
IC003
[+BovercurrentªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven verticals in a period, the unit will automatically turn off.
[Verticaldeflectionstopped] Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.
[Verticaldeflectionovercurrent] Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.
[Whitebalancefailure] If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301. TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
– 8 –
The operating instructions mentioned here are partial abstracts
2
WARNING
• Dangerously high voltages are present inside the TV.
• Operate the TV only between 110 – 240 V AC. (For Hong Kong only: 220 – 240 V AC).
To prevent fire or shock hazard, do not expose the TV to rain or moisture.
Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only.
Do not open the cabinet and the rear cover of the TV. Refer servicing to qualified personnel.
Do not install the TV in hot, humid or excessively dusty places.
Do not install the TV in a confined space, such as a bookcase or built-in cabinet. Do not block the ventilation openings of the TV.
Pull the power cord out by the plug. Do not pull the power cord itself. Disconnect the TV if you are not going to use it for several days.
For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms.
Install the TV in a stable position. Do not allow children to climb onto it.
Do not plug in too many appliances to the same power socket. Do not damage the power cord.
Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not scratch the picture tube.
Using Your New TV
4
Using Your New TV
Getting Started
Step 1
Connect the antenna
If you wish to connect a VCR, see the
Connecting a VCR
diagram below
.
Connecting a VCR
To watch the video, press (see page 12).
KV-XS29M80/XS29M50
: Signal flow
To video and audio outputs
KV-XS29M93
IEC connector (not supplied)
or
: Signal flow
Antenna cable (not supplied)
Antenna cable (not supplied)
Rear of TV
To
1, 2 or 3
(video input)
(yellow)
-L (MONO) (white)
-R (red)
Audio/Video cable (not supplied)
To S video output
Rear of TV
VCR
To ˘ (antenna)
To antenna output
To (S video input)
To (S video input)
Rear of TV
To antenna output
To ˘ (antenna)
Antenna cable (not supplied)
VCR
(yellow)
-L (MONO) (white)
-R (red)
To video and audio outputs
To
1 or 2
(video input)
VIDEO
VIDEO IN
VIDEO OUT
AUDIO R L
12
L
(MONO)
R
WOOFER
123
L
(MONO)
R
R
L
Y
C
B
C
R
VIDEO
VIDEO IN
VIDEO OUT
AUDIO R L
S video cable (not supplied)
Audio/Video cable (not supplied)
To S video output
Antenna cable (not supplied)
: Signal flow
S video cable (not supplied)
from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
– 9 –
SECTION 1-1
GENERAL
(KV-XS29M80)
KV-XS29M80/XS29M97
RM-954 RM-953
5
Using Your New TV
Using Your New TV
Notes
If you connect a monaural VCR, connect the yellow plug to
(the yellow
jack) and the black plug to
-L (MONO) (the white jack).
If you connect a VCR to the ˘ (antenna) terminal, preset the signal
output from the VCR to the program number 0 on the TV.
If both
(S video input) and 1 (video input) at the rear of your TV
are input at the same time, the
(S video input) is automatically
selected. To view 1 (video input), disconnect the S video cable.
When no signal is input to the connected video equipment, the TV screen becomes blue.
KV-XS29M93 only
Do not connect video equipment to the 3 (video input) jacks at the front and the rear of your TV at the same time; otherwise the picture will not be displayed properly on the screen.
Step 2
Insert the batteries into the remote
Note
Do not use old batteries nor use different types of batteries together.
Step 3
Preset the channels automatically
Tips
If you want to stop the automatic channel presetting, press MENU twice.
If your TV has preset an unwanted channel or cannot preset a particular
channel, then preset your TV manually (see page 26).
Note (KV-XS29M80/XS29M50 only)
During automatic channel presetting, your TV screen will indicate
B/G”,
I”, ”D/K or M for the TV system (TV SYS).
Front of TV
1
2
CAUTION
Do not connect the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.
7
Using Your New TV
Using Your New TV
Connecting optional components
You can connect optional audio/video components, such as a VCR, multi disc player, DVD, camcorder, video game or stereo system.
To watch the picture of the connected equipment, press (see page 12).
Connecting a camcorder/video game equipment using the (video input) jacks
Notes
You can also connect video equipment to the … 1 or 2 (video input) jacks at the rear of your TV.
If both
(S video input) and 3 (video input) at the front of your TV
are input at the same time, the
(S video input) is automatically
selected. To view 3 (video input), disconnect the S video cable.
KV-XS29M93 only
Do not connect video equipment to the 3 (video input) jacks at the front and the rear of your TV at the same time; otherwise the picture will not be displayed properly on the screen.
Connecting audio/video equipment using the Ú (monitor output) jacks
KV-XS29M80
To S video output
Front of TV
Camcorder
Video game equipment
To video and audio outputs
: Signal flow
To (S video input)
To
3
(video input)
or
Audio/Video cable (not supplied)
S video cable (not supplied)
(MONO)
continued
(yellow)
-L (MONO)
(white)
-R (red)
Rear of TV
To antenna output
To video and audio inputs
or
Audio system
To audio inputs
VCR
: Signal flow
To Ú (monitor output)
Antenna cable (not supplied)
Audio/Video cable (not supplied)
12
L
(MONO)
R
10
KV-XS29M80/XS29M97
RM-954 RM-953
Using Your New TV
10
Securing the TV
To prevent the TV from falling, secure the TV using one of the following methods:
A
With the supplied screws, attach the band to the TV stand and to the rear of the TV using the provided hole.
or
B
Put the cord or chain through the clamps to secure the TV against a wall or pillar.
Note
Use only the supplied screws. Use of other screws may damage the TV.
20 mm
A
B
3.8mm
or
Using Your New TV
8
Connecting optional components (continued)
(yellow)
-L (MONO)
(white)
-R (red)
Rear of TV
To antenna output
To video and audio inputs
or
Audio system
To audio inputs
VCR
: Signal flow
To Ú (monitor output)
Antenna cable (not supplied)
Audio/Video cable (not supplied)
WOOFER
123
L
(MONO)
R
R
L
Y
C
B
C
R
Note
If you select DVD on your TV scr
een, no signal will be output at the Ú
(monitor output) jacks (see page 12).
Connecting a DVD player using the (video input) jacks
KV-XS29M80
KV-XS29M93 (not used for this model.)
DVD player
Audio/Video cable (not supplied)
(yellow)
-L (MONO) (white)
-R (red)
To 1, or 2 (video input)
: Signal flow
VIDEO
R-AUDIO-L
LINE OUT
123
L
(MONO)
R
Rear of TV
KV-XS29M93
VIDEO
R-AUDIO-L
LINE OUT
123
L
(MONO)
R
DVD player
Audio/Video cable (not supplied)
(yellow)
-L (MONO) (white)
-R (red)
To 1, 2, or 3 (video input)
: Signal flow
Rear of TV
11
KV-XS29M80/XS29M97
RM-954 RM-953
11
Using Your New TV
Using Your New TV
Watching the TV
This section explains functions used while watching TV. Most operations can be done using the remote.
1
Press U to turn on the TV.
When the TV is in the standby mode (the u indicator on the TV is lit red), press u on the remote or PROGR +/– on the TV.
2
Press PROGR +/– or number buttons to select the TV program.
For double digit numbers, press ÷, then the number (e.g., for 25, press ÷, then 2 and 5).
¤
u … ;
Number buttons
JUMP
. +/–
PROGR +/–
1 4 7
-/--
2 5 8 0
3 6 9
FAVORITE
SOUND
MODE
PIC MODE
ENTER
MENU
A/B
SURROUND
MENU +/–/ENTER
or
u indicator
1
2
3
4
5
6
7
8 0
-/--
9
To select a TV program quickly
(1) Press and hold PROGR +/
–.
(2) Release PROGR +/
– when the desir
ed program number appears.
Note
When you select a TV program quickly, the picture may be disrupted. This does not indicate a malfunction.
continued
Using Your New TV
12
To
Turn off temporarily
Turn off completely
Adjust the volume
Mute the sound
Watch the video input (VCR, camcorder, etc.)
Jump back to the previous channel
Display the on-screen information*
Do this
Press u. The
u
indicator on the TV lights up red.
Press U on the TV.
Press ¸ +/–.
Press ¤.
Press to select VIDEO 1, VIDEO 2 , VIDEO 3 or DVD (KV-XS29M93 only). To return to the TV program, press ;.
Press JUMP.
Press
.
* The picture, sound, and either the program number or video mode are
displayed. The on-screen display for the picture and sound information disappears after about 3 seconds.
Changing the menu language
You can change the menu language as well as the on-screen language.
For details on how to use the menu, see
Intr
oducing the menu system
on page 19.
Additional tasks
1
Press MENU.
2
Press + or to select theSET UP icon (
), then
press ENTER.
3
Make sure LANGUAGE
is
selected, then press ENTER.
4
Press + or – to select the desired language (e.g,
), then press ENTER.
The selected menu language appears.
To return to the normal screen
Press MENU.
Watching the TV (continued)
MENU
ENTER
ENTER
ENTER
+
– 12 –
KV-XS29M80/XS29M97
RM-954 RM-953
14
Advanced Operations
Advanced Operations
SOUND MODE
Selecting the picture and sound modes
You can select picture and sound modes and adjust the setting to your preference in PERSONAL option.
Selecting the picture mode
Press PIC MODE repeatedly until you get the desired picture mode.
Select To
DYNAMIC receive high contrast pictures.
STANDARD receive normal contrast pictures.
SOFT receive mild pictures.
PERSONAL receive the last adjusted picture setting from the ADJUST
option in the A/V CONTROL
menu (see page 21).
Selecting the sound mode
Press SOUND MODE repeatedly until you get the desired sound mode.
Select To
DYNAMIC listen to dynamic and clear sound that emphasizes the low and
high tones.
DRAMA listen to sound that emphasizes voice and high tones.
SOFT receive soft sound.
PERSONAL receive the last adjusted sound setting from the ADJUST
option in the A/V CONTROL
menu (see page 21).
Tip
You can also set the picture and sound modes using the menu (see
Changing the A/V CONTROL
setting on page 21).
PIC MODE
PERSONAL
SOFT
STANDARD
DYNAMIC
DYNAMIC
DRAMA
SOFT
PERSONAL
FAVORITE
SOUND MODE
PIC MODE
ENTER
MENU
A/B
SURROUND
PIC MODE
SOUND
MODE
13
Using Your New TV
Using Your New TV
Setting the Wake Up timer
1
Press
until the desired
period of time appears.
The Wake Up timer starts immediately after you have set it.
2
Select the TV program or video mode you want to display when you wake up.
3
Press u or set the Sleep timer if you want the TV to turn off automatically.
The
indicator on the TV lights up orange.
To cancel the Wake Up timer
Press
until WAKE UP TIMER: OFF” appears or turn off the TV’s
main power.
Note
If no buttons or controls are pressed for more than two hours after the TV is turned on using the Wake Up timer, the TV automatically goes into the standby mode. To continue watching the TV, press any button or control on the TV or the remote.
Setting the Sleep timer
Press
until the desired
period of time appears.
The Sleep timer starts immediately after you have set it.
To cancel the Sleep timer
Press
until SLEEP TIMER: OFF” appears or turn the TV off.
WAKE UP TIMER:10M
WAKE UP TIMER:OFF
WAKE UP TIMER:12H00M
After 10 minutes
No Wake Up Timer After 12 hours
SLEEP TIMER:30M
SLEEP TIMER:60M
SLEEP TIMER:OFF
SLEEP TIMER:90M
After 30 minutes
No Sleep Timer
After 60 minutes
After 90 minutes
13
KV-XS29M80/XS29M97
RM-954 RM-953
15
Advanced Operations
1
Press FAVORITE.
2
Press the number button from 1 to 6 to select the desired channel.
Tip
To program your favorite channels, see
Pr
ogramming your favorite
channels on page 24.
Viewing your favorite channels
You can display and select six of your favorite channels directly from your TV screen.
Number buttons
FAVORITEFAVORITE
1 4 7
-/--
2 5 8 0
3 6 9
FAVORITE
SOUND
MODE
PIC MODE
ENTER
MENU
A/B
SURROUND
FAVORITE
1
1
2
3
4
5
6
Advanced Operations
16
Advanced Operations
Press SURROUND repeatedly until you receive the desired surround sound.
Listening with surround sound
The surround feature enables you to enjoy the sound effects of a concert hall or movie theater.
Select To
HIGH listen to sound that spreads out over a large area, giving the feeling
of being at a concert hall.
LOW listen to the sound that gives the feeling of being at a live concert.
OFF turn off the surround sound.
The surround of your TV is categorized as TruSurround.
TM
is a trademark of SRS Labs, Inc. SRS and the SRS symbol are registered trademarks of SRS Labs, Inc. in the United States and selected foreign countries. SRS and TruSurround are incorporated under license from SRS Labs, Inc. and are protected under United States Patent Nos. 4,748,669 and 4,841,572 with numerous additional issued and pending foreign patents.
SURROUND
FAVORITE
SOUND MODE
PIC MODE
ENTER
MENU
A/B
SURROUND
SURROUND: LOW
SURROUND: HIGH
SURROUND: OFF
SURROUND
KV-XS29M80/XS29M97
RM-954 RM-953
14
19
Adjusting Your Setup (MENU)
Introducing the menu system
The MENU button lets you open a menu and change the settings of your TV. Here's an overview of the menu system.
Level 1 Level 2 Level 3/Function
A/V CONTROL
PICTURE MODE
Select the picture mode.
“DYNAMIC” n “STANDARD” n “SOFT” n “PERSONAL” n “ADJUST”
ADJUST Adjust the PERSONAL option. PICTURE
n
COLORnBRIGHTnHUEnSHARP
SOUND MODE
Select the sound mode.
“DYNAMIC” n “DRAMA” n “SOFT” n “PERSONAL” n “ADJUST”
ADJUST Adjust the PERSONAL option.
BASSnTREBLEnBALANCEnBBE*
SURROUND Select the surround mode.
HIGHn LOWnOFF
SET UP”“LANGUAGE”
Change the menu language.
ENGLISH”–
(Chinese)/
(Arabic)/
(Thai)
CHILD LOCK Block the channel independently.
PIC ROTATION” Adjust the picture position.
FAVORITE CH”
Program favorite channels.
INTELLIGENT VOL
Adjust volume automatically.
CH PRESET”“AUTO PROGRAM” Preset channels automatically.
MANUAL PROGRAM
Preset channels manually.
SKIP Skip unwanted or unused program positions.
TV SYS Select the TV system.
“B/G”n “I”n “D/K”n “M”
COL SYS Select the color system.
AUT
On
PAL nSECAMnNTSC3.58nNTSC4.43
Return icon
A/V CONTROL icon
SET UP icon
CH PRESET icon
Name of the current menu
Menu level 3
Menu level 2
Adjusting Your Setup (MENU)
Menu level 1
* The BBE is manufactured by Sony Corporation under license from BBE
Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No. 4,482,866. The word “BBE” and the BBE symbol are the trademarks of BBE Sound, Inc.
Adjusting Your Setup (MENU)
continued
20
Adjusting Your Setup (MENU)
How to use the menu
You can use the buttons on the remote and on the TV as well to display the menu and adjust the settings.
1
Press MENU to display the menu.
2
Press + or – to select the desired item.
3
Press ENTER to confirm your option and go to the next menu level.
Other menu operations
To Press
Adjust the setting value +/–
Return to the previous menu level ENTER
Cancel the menu MENU
+ / – /ENTER
MENU
Front of TV
Tips
To return from Menu Level 2 to Level 1, press + / – to select the return icon (
), then press ENTER.
• You can also use the buttons on the TV for menu operations. ¸ +/– work as + /– on the remote and works as ENTER on the remote.
Notes
If more than 60 seconds elapse between entries, the menu screen automatically disappears.
With better resolution of the on-screen fonts, interlace scanning might cause flickers on some parts of the menu screen. This does not indicate a malfunction.
FAVORITE
SOUND MODE
PIC MODE
ENTER
MENU
A/B
SURROUND
MENU
ENTER
+
+
PROGR
AUTO
PROGR
MENU
Introducing the menu system (continued)
15
KV-XS29M80/XS29M97
RM-954 RM-953
KV-XS29M80/XS29M97
21
Adjusting Your Setup (MENU)
Changing the “A/V CONTROL” setting
The A/V CONTROL
menu allows
you to change the picture and sound settings.
1
Press MENU.
2
Make sure the
A/V
CONTROL icon (
) is selected, then press ENTER.
3
Press + or to select eitherPICTURE MODE
”, “SOUND MODE, orSURROUND, then press
ENTER.
4
Press + or – to select the desired option, then press ENTER.
For Select
PICTURE MODE
either DYNAMIC, ST
ANDARD, SOFT, PERSONAL*, or ADJUST.
SOUND MODE
either DYNAMIC”, “DRAMA”, “SOFT”, “PERSONAL*, or ADJUST”.
SURROUND either HIGH, LOW, or OFF.
* When the “PERSONAL” mode is selected, the last adjusted pictur
e
and sound settings from the “ADJUST” option ar
e received (see
page 22).
Tip
For details on the options under
PICTURE MODE
”, “SOUND MODE
and SURROUND, see page 14 and 16 r
espectively.
To return to the normal screen
Press MENU.
+ / – /ENTER
MENU
FAVORITE
SOUND MODE
PIC MODE
ENTER
MENU
A/B
SURROUND
ENTER
ENTER
ENTER
continued
22
Adjusting Your Setup (MENU)
Adjusting the
ADJUST options under
PICTURE MODE
1
Press + or – to select the desired item (e.g.,
COLOR),
then press ENTER.
2
Adjust the value according to the following table, then press ENTER.
For Press – to Press + to
PICTURE
decrease picture contrast increase picture contrast
COLOR
decrease color intensity increase color intensity
BRIGHT
darken the picture brighten the picture
HUE
* increase red picture tones increase green picture tones
SHARP
soften the picture sharpen the picture
* You can adjust
HUE
for the NTSC color system only.
3
Repeat the above steps to adjust other items.
The adjusted settings will be received when you select
PERSONAL
.
Adjusting the
ADJUST
options under
SOUND MODE
1
Press + or – to select the desired item (e.g.,
BALANCE
),
then press ENTER.
2
Adjust the value according to the following table, then press ENTER.
For Press – to Press + to
BASS
decrease the bass increase the bass
TREBLE
decrease the treble increase the treble
BALANCE
increase the left speakers volume
increase the right speakers volume
BBE
select HIGH for higher enhancement of sound clarity; select LOW for lower enhancement of sound clarity; select OFF to turn off the BBE sound
3
Repeat the above steps to adjust other items.
The adjusted settings will be received when you select
PERSONAL.
Tip
For details on the menu system and how to use the menu, refer to “Introducing the menu system
on page 19.
ENTER
COLOR 80
BALANCE 00
ENTER
Changing the “A/V CONTROL” setting
(continued)
RM-954 RM-953
16
23
Adjusting Your Setup (MENU)
Changing the SET UP setting
The SET UP menu allows you to change the menu language, block channels, adjust the picture position, program your favorite channels and adjust volume automatically.
MENU
Number buttons
+ / – / ENTER
1 4 7
-/--
2 5 8 0
3 6 9
FAVORITE
SOUND
MODE
PIC MODE
ENTER
MENU
A/B
SURROUND
1
Press MENU.
2
Press + or to select theSET UP icon (
), then
press ENTER.
3
Press + or – to select the desired option (e.g.,
INTELLIGENT VOL
”),
then press ENTER.
Select To
LANGUAGE Change the menu language (see
Changing the menu
language on page 12).
CHILD LOCK
Prevent children from watching certain channels (see
Blocking the channels (
CHILD LOCK“)” on page 25).
PIC ROTATION“ Adjust the picture position when it is not aligned to the
TV screen. Press + or – to adjust the picture position, then press ENTER.
FAVORITE CH“ Program channels for direct selection (see
Pr
ogramming
your favorite channels
on page 24).
INTELLIGENT VOL
Adjust the volume of each TV program automatically. Press + or – to select “ON”, then pr
ess ENTER. To turn off the “Intelligent Volume function, select OFF, then press ENTER.
To return to the normal screen.
Press MENU.
ENTER
ENTER
+
+
PIC ROTATION
ENTER
continued
24
Adjusting Your Setup (MENU)
Changing the
SET UP setting (continued)
1
Press MENU.
2
Press + or to select theSET UP icon (
), then
press ENTER.
3
Press + or to selectFAVORITE CH, then
press ENTER twice.
4
Press + or –, or number buttons to program the desired channel (e.g., PR03), then press ENTER.
5
To continue programming other favorite channels, press + or – and then press ENTER. After that, repeat step 4.
To return to the normal screen
Press MENU.
Tip
For details on the menu system and how to use the menu, refer toIntroducing the menu system
on page 19.
or
ENTER
ENTER
ENTER
1
2
3
4
5
6
7
8 0
-/--
9
ENTER
+
++
+++++++
PRO
R02
:
B/G
COL S YS
:
AUTO
AUTO PROGRAM M S T
+
++
+++++++
PRO
R02
:
B/G
COL S YS
:
AUTO
AUTO PROGRAM S
T
3
+
Programming your favorite channels
The FAVORITE CH feature enables you to program up to six channels for direct selection.
17
KV-XS29M80/XS29M97
RM-954 RM-953
KV-XS29M80/XS29M97
25
Adjusting Your Setup (MENU)
1
Press MENU.
2
Press + or to select theSET UP icon (
), then
press ENTER.
3
Press + or to selectCHILD LOCK, then press
ENTER.
4
Press + or –, or number buttons to select the desired channel, then press ENTER.
5
Press + or – to select ON, then press ENTER.
The lock symbol (
)
appears on the screen.
To unlock the channel, select OFF.
6
To continue locking other channels, press ENTER and then repeat step 4 to 5.
To return to the normal screen
Press MENU.
Note
If you preset a locked channel, that particular channel will be unlocked automatically (see page 26).
Blocking the channels (
CHILD LOCK)
You can prevent your children from watching certain channels by using the CHILD LOCK featur
e.
or
ENTER
ENTER
ENTER
1
2
3
4
5
6
7
8 0
-/--
9
ENTER
+
+
+
+
ENTER
26
Adjusting Your Setup (MENU)
Select
AUTO PROGRAM
MANUAL PROGRAM
SKIP
TV SYS
COL SYS
To
preset channels automatically.
preset channels manually. See Presetting channels manually on page 27.
skip unwanted or unused program numbers. 1 Press + or – until the unused or unwanted program
number appears, then press ENTER.
2 Press + or – to select “ON”, then pr
ess ENTER.
To put the skipped program number back on, select OFF, then press ENTER.
select the TV system. See
Pr
esetting channels manually
on page 27.
select the color system. Normally, set this to “AUTO”.
Changing the Channel Preset (CH PRESET) setting
The CH PRESET menu allows you to adjust the setup of your TV. For example, you can receive a channel with a weak signal that fails to be tuned in by automatic presetting.
1
Press MENU.
2
Press + or to select theCH PRESET icon (
),
then press ENTER.
3
Press + or – to select the desired option (e.g., SKIP), then press ENTER.
ENTER
ENTER
+
+
+ / – /ENTER
MENU
FAVORITE
SOUND MODE
PIC MODE
ENTER
MENU
A/B
SURROUND
RM-954 RM-953
18
27
Adjusting Your Setup (MENU)
Presetting channels manually
1
After selecting
MANUAL PROGRAM, select the program number to which you want to preset a channel. (1) Make sure “PR” is
selected , then press ENTER.
(2)
Press + or – until the program number you want to preset (e.g., program number
10) appears on the menu, then press ENTER
.
2
Select the desired channel.
(1) Press + or – to select
either VHF LOW,
VHF HIGH orUHF, then press
ENTER.
(2) Press + or – until the
desired channel picture appears on the TV screen, then press ENTER.
3
If the sound of the desired channel is abnormal, select the appropriate TV system.
(1) Press + or – to select
TV SYS, then press ENTER.
(2) Press + or – until the
sound becomes normal (e.g., “M”), then press ENTER.
ENTER
+
+ +
+
+ +
ENTER
ENTER
ENTER
+
+ +
+
+ +
continued
ENTER
ENTER
+
+ +
+
+ +
28
Adjusting Your Setup (MENU)
ENTER
ENTER
ENTER
+
+ +
+
+ +
+
4
If you are not satisfied with the picture and sound quality, you may improve them by using fine tuning.
(1) Press + or – to select
FINE, then press ENTER.
(2) Press + or – to select
MANUAL, then press ENTER.
(3) Press + or – until the
picture and sound quality are optimal, then press ENTER.
The + or – icon on the menu flashes while tuning.
To return to the normal screen
Press MENU.
Notes
If you preset a locked channel, that particular channel will be unlocked automatically (see page 25).
The TV system (
TV SYS) and the fine tuning (
FINE) settings ar
e
memorized for each program number.
Changing the Channel Preset (CH PRESET) setting (continued)
19
KV-XS29M80/XS29M97
RM-954 RM-953
29
Additional Information
Additional Information
Self-diagnosis function
Your TV is equipped with a self-diagnosis function. If there is a problem with your TV, the
u
indicator flashes red. The number of
times the
u
indicator flashes indicates the possible causes.
1
Check that the red flashes of the
u
indicator is about 3 seconds per interval.
2
Count the number of times the
u
indicator flashes.
3
Press U (main power) to turn off your TV.
4
Inform your nearest Sony service center about the number of times the
u
indicator flashes. Be sure to note the model name and serial number located on the rear of your TV.
Front of TV
u indicator
Additional Information
30
Additional Information
Troubleshooting
If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer .
Possible causeSymptom
Solutions
Snowy picture
Noisy sound
Distorted picture
Noisy sound
Good picture
Noisy sound
No picture
No sound
Connection is loose or the cable is damaged.
Channel presetting is inappropriate or incomplete.
The antenna type is inappropriate.
The antenna direction is inappropriate.
Signal transmission is low.
Broadcast signals are too strong.
The TV system setting or channel presetting is inappropriate or incomplete.
The power cord, antenna or VCR is not connected.
The TV is not turned on.
Check the antenna cable and connection on the TV, VCR and on the wall.
Display the CH PRESET menu and select MANUAL PROGRAM to preset the channel again.
Check the antenna type (
VHF/UHF”).
Contact a Sony dealer for advice.
Adjust the antenna direction. Contact a Sony dealer for advice.
Try using a booster.
Turn off or disconnect the booster if it is
in use.
If the sound of all the channels are noisy, display the CH PRESET menu and check the TV system (
TV SYS) setting,
then select “AUTO PROGRAM” to pr
eset
the channels again.
If the sound of some channels are noisy, select the channel, then display the
CH PRESET menu and select the appropriate TV system (TV SYS”).
Check the power cord, antenna and the VCR connections.
Press u (power).
Press U (main power) on the TV to turn
off the TV for about five seconds, then turn it on again.
Page
4
26
26
26
4
12
11
20
KV-XS29M80/XS29M97
RM-954 RM-953
31
Additional Information
Press ¸ + to increase the volume level.
Press ¤ to cancel the muting.
Press A/B until a good sound is
heard. (KV-XS29M93 only)
Do not use a hair dryer or other equipment near the TV.
Adjust the antenna direction for minimum interference. Contact a Sony dealer for advice.
Use a highly directional antenna.
Use the fine tuning (
FINE) function.
Adjust the antenna direction. Contact a
Sony dealer for advice.
Turn off or disconnect the booster if it is in use.
Display the A/V CONTROL
menu and
select ADJUST of PICTURE MODE
”,
then adjust the COLOR level.
Display the CH PRESET menu and
check the color system (
COL SYS)
setting (usually set this to
AUT
O).
Adjust the antenna direction. Contact a Sony dealer for advice.
Keep external speakers or other electrical equipment away from the TV. Do not move the TV while the TV is turned on. Press U (main power) on the TV to turn off the TV for about five minutes, then turn it on again.
Press A/B until AUTO appears on the screen.
The volume level is too low.
The sound is muted.
Broadcast signal has a
transmission problem.
There is local interference from cars, neon signs, hair dryers, power generators, etc.
Broadcast signals are reflected by nearby mountains or buildings.
The antenna direction is inappropriate.
Use of a booster is inappropriate.
The color level setting is too low.
The color system setting is inappropriate.
The antenna direction is inappropriate.
The magnetic disturbance from external speakers or other equipment, or the direction of the earths magnetic field may affect the TV.
The stereo reception setting is inappropriate.
Possible causeSymptom Solutions
Page
12
12
17
28
21
26
17
Good picture
No sound
Dotted lines or stripes
Double images or ghosts
No color
Abnormal color patches
TV cannot receive stereo broadcast signal. (KV-XS29M93 only)
continued
32
Additional Information
Possible causeSymptom
Solutions
Troubleshooting (continued)
Page
4
17
23
28
29
Connection is loose or
the cable is damaged.
The antenna direction is inappropriate.
Broadcast signal has a transmission problem.
The terrestrial magnetism affects your TV set.
There is interference from external sources, e.g., heavy machineries, nearby broadcast station.
Your TV may need service.
Changes in room temperature sometimes make the TV cabinet expand or contract, making a noise. This does not indicate a malfunction.
The TVs demagnetizing function is working. This does not indicate a malfunction.
Stereo broadcast sound switches on and off or is distorted.
or
The sound switches between monaural and stereo frequently. (KV-XS29M93 only)
Picture slant
Lines moving across the TV screen.
The
u
indicator on your TV flashes red a number of times between 3-second intervals.
TV cabinet creaks.
A “boom” sound is heard when the TV is turned on.
Check the antenna cable and connection on the TV, VCR and on the wall.
Adjust the antenna direction. Contact a Sony dealer for advice.
Press A/B until a good sound is heard.
Display the SET UP menu and adjustPIC ROTATION” so that the picture is
aligned to the TV screen.
Use the fine tuning (
FINE) function.
Contact your nearest Sony service center.
21
KV-XS29M80/XS29M97
RM-954 RM-953
33
Additional Information
Identifying parts and controls
Front panel
(MONO)
PROGR
AUTO
PROGR
MENU
PageFunction
Preset channels automatically.5 Turn off completely or 11
turn on the TV. Select program number. 11 Adjust volume. 12 Select TV or video input. 12 Display the menu. 20 Headphones jack.
AUTO PROGR
!
PROGR +/– 2 +/–
t
MENU
i
Button
continued
34
Additional Information
Remote control
1 4 7
-/--
2 5 8 0
3 6 9
FAVORITE
SOUND
MODE
PIC MODE
ENTER
MENU
A/B
SURROUND
Identifying parts and controls (continued)
Button function
For general TV operations
For Teletext operations
Names/symbols of buttons on the remote are indicated in different colors to represent the available functions.
Label color
White
Green
Page
Button
Function
PROGR +/– 0 – 9, ÷
. +/– u
… ; ¤
JUMP Timer operations
PIC MODE SOUND MODE FAVORITE SURROUND A/B
(KV-XS29M93 only) Menu operations
MENU + or – ENTER
Teletext operations (Not used for KV-XS29M93/XS29M80/XS29M50)
p
(red, green,
yellow, blue)
Select program number. 11
Input numbers. 11
Adjust volume. 12
Turn off temporarily or turn on the TV. 12
Select TV or video input. 12
Display the TV program. 12
Mute the sound. 12
Display on-screen information.
12
Jump to previous channel. 12
Set TV to turn on automatically.
13
Set TV to turn off automatically.
13
Select picture mode. 14
Select sound mode. 14
Display favorite channels. 15
Select surround mode. 16
Select stereo/bilingual mode.
17
Display the menu. 20
Select and adjust item. 20
Confirm selected item. 20
Display Teletext broadcast.
Enlarge the Teletext display.
Reveal concealed information. –
Stop Teletext page from scrolling.
Display Teletext service contents.
Show TV screen while – waiting for Teletext page.
Access a Fastext menu
KV-XS29M80/XS29M97
RM-954 RM-953
22
8
Using Your New TV
Notes
Some DVD player terminals may be labeled differently:
Since the high quality pictures on a DVD disc contain a lot of information,
picture noise may appear. In this case, adjust the sharpness (
SHARP) in the
PERSONAL ADJUST menu of the PICTURE MODE menu (see page 25).
Connect your DVD player directly to your TV. Connecting the DVD player through other video equipment will cause unwanted picture noise.
Connecting a DVD player using the
(component
video input) jacks
1 Connect R and L under
(component video input) on your TV to the LINE OUT,
AUDIO R and L output connectors on your DVD player.
2 Using a component video cable, connect Y, C
B
, and C
R
under
(component video
input) on your TV to the COMPONENT VIDEO OUT Y, C
B
, and C
R
output
connectors on your DVD player.
DVD player
To L (white) R (red)
Audio cable (not supplied)
To component video output
Component video cable (not supplied)
To audio output
: Signal flow
To (component video input)
Connect To (on the DVD player)
Y (green) Y C
B
(blue) C
b
, B-Y or P
B
CR (red) C
r
, R-Y or P
R
VIDEO
R-AUDIO-L
LINE OUT
Y
COMPONENT VIDEO OUT
S VIDEO OUT
CB C
R
R
L
Y
C
B
C
R
Connecting optional components (continued)
Connecting a DVD player using the (video input) jacks
Connect 1, 2, or 3 (video input)
/
(audio/video) connectors on your TV to
LINE OUT on your DVD player.
VIDEO
R-AUDIO-L
LINE OUT
123
L
(MONO)
R
DVD player
Audio/Video cable (not supplied)
(yellow)
-L (MONO) (white)
-R (red)
To 1, 2, or 3 (video input)
: Signal flow
7
Using Your New TV
Using Your New TV
Connecting optional components
You can connect optional audio/video components, such as a VCR, multi disc player, camcorder, video game or stereo system. To watch the picture of the connected equipment, press (see page 11).
Connecting a camcorder/video game equipment using the (video input) jacks
Notes
You can also connect video equipment to the … 1, 2 or 3 (video input)
jacks at the rear of your TV.
If both
(S video input) and 3 (video input) at the front of your TV
are input at the same time, the
(S video input) is automatically
selected. To view 3 (video input), disconnect the S video cable.
Do not connect video equipment to the … 3 (video input) jacks at the
front and the rear of your TV at the same time; otherwise the picture will not be displayed properly on the screen.
Connecting audio/video equipment using the Ú (monitor output) jacks
Note
When connecting a monaural VCR, connect the yellow plug to
(the
yellow jack) and the black plug to
-L (MONO) (the white jack).
To S video output
Front of TV
Camcorder
Video game equipment
To video and audio outputs
(yellow)
-L (MONO)
(white)
-R (red)
Rear of TV
To antenna output
To video and audio inputs
or
Audio system
To audio inputs
VCR
: Signal flow
: Signal flow
To (S video input)
To
3 (video input)
To Ú (monitor output)
or
Audio/Video cable (not supplied)
S video cable (not supplied)
Antenna cable (not supplied)
Audio/Video cable (not supplied)
(MONO)
WOOFER
123
L
(MONO)
R
R
L
Y
C
B
C
R
continued
25
KV-XS29M80/XS29M97
RM-954 RM-953
KV-XS29M80/XS29M97
9
Using Your New TV
Using Your New TV
Securing the TV
To prevent the TV from falling, secure the TV using one of the following methods:
A
With the supplied screws, attach the band to the TV stand and to the rear of the TV using the provided hole.
or
B
Put the cord or chain through the clamps to secure the TV against a wall or pillar.
Note
Use only the supplied screws. Use of other screws may damage the TV.
20 mm
A
B
3.8 mm
or
10
Using Your New TV
Watching the TV
This section explains functions used while watching TV. Most operations can be done using the remote.
1
Press U to turn on the TV.
When the TV is in the standby mode (the u indicator on the TV is lit red), press u on the remote or PROGR +/– on the TV.
2
Press PROGR +/– or number buttons to select the TV program.
For double digit numbers, press ÷, then the number (e.g., for 25, press ÷, then 2 and 5).
To select a TV program quickly
(1) Press and hold PROGR +/
–.
(2) Release PROGR +/
– when the desir
ed program number appears.
Note
When you select a TV program quickly, the picture may be disrupted. This does not indicate a malfunction.
¤
u … ;
Number buttons
JUMP
. +/–
PROGR +/–
MENU
V/b/v/B/ENTER
or
u indicator
1
2
3
4
5
6
7
8 0
-/--
9
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
SOUND
MODE
SURROUND
PIP PROGR
PIP PROGR
ENTER
PIC
MODE
RM-954 RM-953
26
12
Using Your New TV
Setting the Wake Up timer
1
Press
until the desired
period of time appears.
2
Select the TV program or video mode you want to display when you wake up.
3
Press u or set the Sleep timer if you want the TV to turn off automatically.
The
indicator lights up orange.
To cancel the Wake Up timer
Press
until WAKE UP TIMER: OFF appears or turn off the TV’s
main power.
Notes
The Wake Up timer starts immediately after the on-screen display disappears.
If no buttons or controls are pressed for more than two hours after the TV is turned on using the Wake Up timer, the TV automatically goes into the standby mode. To continue watching the TV, press any button or control on the TV or the remote.
Setting the Sleep timer
Press
until the desired
period of time appears.
To cancel the Sleep timer
Press
until SLEEP TIMER: OFF appears or turn the TV off.
WAKE UP TIMER:10M
WAKE UP TIMER:OFF
After 10 minutes
No Wake Up Timer
WAKE UP TIMER:12H00M
After 12 hours
SLEEP TIMER:30M
SLEEP TIMER:60M
SLEEP TIMER:OFF
SLEEP TIMER:90M
After 30 minutes
No Sleep Timer
After 60 minutes
After 90 minutes
Watching the TV (continued)
11
Using Your New TV
Using Your New TV
To
Turn off temporarily
Turn off completely
Adjust the volume
Mute the sound
Watch the video input (VCR, camcorder, etc.)
Jump back to the previous channel
Display the on-screen information*
Do this
Press u. The u indicator on the TV lights up red.
Press U on the TV.
Press . +/–.
Press ¤.
Press
to select VIDEO 1”, “VIDEO 2 or VIDEO 3”.
To return to the TV program, press
;
.
Press JUMP.
Press
.
Additional tasks
ENTER
To return to the normal screen
Press MENU.
ENTER
ENTER
ENTER
ENTER
continued
+
* The picture, sound, and either the program number or video mode are
displayed. The on-screen display for the picture and sound information disappears after about 3 seconds.
Changing the menu language
You can change the menu language as well as the on-screen language.
For details on how to use the menu, see
Intr
oducing the menu system
on page 22.
1
Press MENU.
2
Press V or v to select the SET UP icon (
), then
press ENTER.
3
Make sure “LANGUAGE” is selected, then press ENTER.
4
Press V or v to select the desired language (e.g.,
), then press
ENTER.
The selected menu language appears.
27
KV-XS29M80/XS29M97
RM-954 RM-953
13
Advanced Operations
SOUND MODE
PIC MODE
Selecting the picture and sound modes
You can select picture and sound modes and adjust the setting to your preference in PERSONAL option.
Selecting the picture mode
Press PIC MODE repeatedly until you get the desired picture mode.
Select To
DYNAMIC receive high contrast pictures.
STANDARD receive normal contrast pictures.
SOFT receive mild pictures.
PERSONAL receive the last adjusted picture setting from the ADJUST
option in the A/V CONTROL
menu (see page 24 and 25).
Selecting the sound mode
Press SOUND MODE repeatedly until you get the desired sound mode.
Select To
DYNAMIC listen to dynamic and clear sound that emphasizes the low and
high tones.
DRAMA listen to sound that emphasizes voice and high tones.
SOFT receive soft sound.
PERSONAL receive the last adjusted sound setting from the ADJUST
option in the A/V CONTROL
menu (see page 24 and 25).
Tip
You can also set the picture and sound modes using the menu (seeChanging the A/V CONTROL
setting on page 24).
PERSONAL
SOFT
STANDARD
DYNAMIC
DYNAMIC
DRAMA
SOFT
PERSONAL
PIC
MODE
Advanced Operations
Advanced Operations
14
Advanced Operations
1
1
Press FAVORITE.
2
Press the number button from 1 to 6 to select the desired channel.
Tip
To program your favorite channels, see
Pr
ogramming your favorite
channels on page 28.
Viewing your favorite channels
You can display and select six of your favorite channels directly from your TV screen.
Number buttons
FAVORITE
1
2
3
4
5
6
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
SOUND
MODE
SURROUND
PIP PROGR
PIP PROGR
ENTER
PIC
MODE
28
KV-XS29M80/XS29M97
RM-954 RM-953
15
Advanced Operations
Watching two programs at the same time
— PIP
With the Picture-in-Picture (PIP) feature, you can display a different TV program or video directly within the main picture.
Displaying the PIP screen
Press
.
/
/
/
V/v/ENTER
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
SOUND
MODE
SURROUND
PIP PROGR
PIP PROGR
ENTER
PIC
MODE
continued
16
Advanced Operations
Additional PIP tasks
To
change a TV program in the PIP screen
change a video input in the PIP screen
swap pictures between the main and PIP screens
freeze the PIP screen
To return to the normal screen
Press
.
Tips
You can also display the PIP screen using the menu (see
Changing the
PIP setting on page 26).
You can change the position of the PIP screen (see “Changing the PIP
setting on page 26).
Notes
When you display a video input on the PIP screen at a faster/slower
speed, the picture may be disrupted depending on the VCR type.
If you display different color systems on the PIP screen, the size of the PIP
screen may be different and the picture may be disrupted. This does not indicate a malfunction of the TV.
Press
V or v.
.
.
.
To unfreeze the screen, press the
button again.
Watching two programs at the same time—PIP (continued)
29
KV-XS29M80/XS29M97
RM-954 RM-953
17
Advanced Operations
Press SURROUND repeatedly until you receive the desired surround sound.
Select To
HIGH listen to sound that spreads out over a large area, giving the feeling
of being at a concert hall.
LOW listen to the sound that gives the feeling of being at a live concert.
OFF turn off the surround sound.
The surround of your TV is categorized as TruSurround.
TM
is a trademark of SRS Labs, Inc. SRS and the SRS symbol are
registered trademarks of SRS Labs, Inc. in the United States and selected foreign countries. SRS and TruSurround are incorporated under license from SRS Labs, Inc. and are protected under United States Patent Nos. 4,748,669 and 4,841,572 with numerous additional issued and pending foreign patents.
Listening with surround sound
The surround feature enables you to enjoy the sound effects of a concert hall or movie theater.
FAVORITE
SOUND
MODE
SURROUND
PIP PROGR
PIP PROGR
ENTER
SURROUND: LOW
SURROUND: HIGH
SURROUND: OFF
SURROUND
18
Advanced Operations
1
2
3
4
5
6
7
8 0
-/--
9
PIC
MODE
Broadcasting On-screen display (Selected sound)
NICAM stereo
NICAM bilingual
NICAM monaural
Selecting a stereo or bilingual program
You can enjoy stereo sound or bilingual programs of NICAM and A2 (German) stereo systems.
Press A/B repeatedly until you receive the sound you want.
The on-screen display changes to show the selected sound and the  indicator on the TV lights up red.
When receiving a NICAM program
A/B
NICAM
MONO
(Stereo sound)
(Regular sound)
NICAM
MAIN
MONO
(Main sound)
(Regular sound)
NICAM
SUB
(Sub sound)
NICAM
MAIN
MONO
(Main sound)
(Regular sound)
30
KV-XS29M80/XS29M97
RM-954 RM-953
19
Advanced Operations
MONO
AUTO
System
NICAM
A2 (German)
Receiving area
Hong Kong, Singapore, New Zealand, Malaysia, Thailand, etc.
Australia, Malaysia, Thailand, etc.
When receiving an A2 (German) program
Receiving area for NICAM and A2 (German) programs
Notes
If the signal is very weak, the sound becomes monaural automatically.
If the stereo sound is noisy when receiving a NICAM program, select
MONO. The sound becomes monaural, but the noise is reduced.
Before receiving a NICAM stereo program in China, please check the
NICAM broadcast condition at your area. When receiving a NICAM stereo program, the receiving conditions might vary depending on area. In addition, different strength of the NICAM broadcast signal might affect the receiving quality.
If the sound is distorted or noisy when receiving a monaural program through the ˘ (antenna) terminal
Press A/B repeatedly until MONO appears on the scr
een.
To cancel the monaural sound setting, press A/B again until AUTO appears on the screen.
Notes
The MONO or AUT
O setting is memorized for each program
position.
You cannot receive stereo broadcast signal when the TV is in the
MONO
setting. Normally set the TV to
AUT
O.
STEREO
MONO
(Stereo sound)
(Regular sound)
MAIN
SUB
(Main sound)
(Sub sound)
Broadcasting On-screen display (Selected sound)
A2 (German) stereo
A2 (German) bilingual
22
Adjusting Your Setup (MENU)
*
The BBE is manufactured by Sony Corporation under license from BBE Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No. 4,482,866. The word BBE and the BBE symbol are the trademarks of BBE Sound, Inc.
Introducing the menu system
The MENU button lets you open a menu and change the settings of your TV. Here’s an overview of the menu system.
Level 1 Level 2 Level 3/Function
A/V CONTROL
PICTURE MODE
Select the picture mode.
“DYNAMIC” n “STANDARD” n “SOFT” n “PERSONAL” n “ADJUST”
ADJUST Adjust the PERSONAL option
“PICTURE” n “COLOR” n “BRIGHT” n “HUE” n “SHARP”
SOUND MODE
Select the sound mode.
“DYNAMIC” n “DRAMA” n “SOFT” n “PERSONAL“ n “ADJUST”
ADJUST Adjust the PERSONAL option.
“BASS” n “TREBLE” n “BALANCE” n “BBE”
*
SURROUND Select the surround mode.
“HIGH” n “LOW” n “OFF”
PIP”“PIP POSITION”
Change the position of the PIP screen.
PIP Display a sub screen within the main picture.
SWAP Exchange program between main screen and sub
screen
SET UP”“LANGUAGE Change the menu language.
ENGLISH -
(Chinese)/
(Arabic)/
(Thai)
CHILD LOCK
Lock the channel independently.
PIC ROTATION” Adjust the picture position.
FAVORITE CH” Program favorite channels.
INTELLIGENT VOL
Adjust volume automatically.
CH PRESET”“AUTO PROGRAM” Preset channels automatically.
MANUAL PROGRAM
Preset channels manually.
SKIP Skip unwanted or unused program positions.
TV SYS Select the TV system.
“B/G” n “I” n “D/K” n “M”
COL SYS Select the color system.
“AUTO” n “PAL ” n “SECAM” n “NTSC3.58” nNTSC4.43
Return icon
A/V CONTROL icon
PIP icon
CH PRESET icon
Name of the current menu
Menu level 3
Menu level 2
Adjusting Your Setup (MENU)
Menu level 1
SET UP icon
Menu guide icon
31
KV-XS29M80/XS29M97
RM-954 RM-953
Loading...
+ 78 hidden pages