Sony KV-XF29M97, KV-XF29M67 Service manual

Self Diagnosis
Supported model
5MODEL COMMANDER DEST. CHASSIS NO.

KV-XF29M97 RM-953 India SCC-U22L-A KV-XF29M67 RM-953 India SCC-U22M-A

MODEL COMMANDER DEST. CHASSIS NO.
BG-3S
CHASSIS
PIC MODE
2
1
3
5
4
6
7
9
8
-/--
0
FAVORITE
SOUND
SURROUND
MODE
TRINITRON
®
COLOR TV
KV-XF29M97/XF29M67
RM-953
Power requirements 110-240 V AC, 50/60 Hz Power consumption (W) Indicated on the rear of the TV Television system B/G, I, D/K, M Color system PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58 Channel coverage
B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41 I UHF: B21 to B68 / CATV: S01 to S03, S1 to S41 D/K VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60
M VHF: A2 to A13 / UHF: A14 to A79 /
˘ (Antenna) 75-ohm external terminal Audio output 6W + 6W 3D WOOFER 15W Number of terminal
D (Video) Input: 3 Output: 1 Phono jacks; 1 VP-P, 75 ohms (Audio) Input: 3 Output: 1 Phono jacks; 500 mVrms
(S Video) Input: 2 Y : 1 Vp-p, 75 ohms,
2 (Headphone) Output: 1 Minijack
Picture tube 29 inch
Tube size (cm) 72 Measured diagonally Screen size (cm) 68 Measured diagonally
Dimension (w/h/d, mm) 794 × 589 × 517 Mass (kg) 54

SPECIFICATIONS

Note
CATV: Z1 to Z39, S01 to S03, S1 to S41
CATV: A-8 to A-2, A to W+4, W+6 to W+84
unbalanced, sync negative
C : 0.286 Vp-p, 75 ohms
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
– 2 –
!!
! ON
!!

TABLE OF CONTENTS

KV-XF29M97/XF29M67
RM-953
Section Title Page
SELF DIAGNOSIS FUNCTION................................ 4
1. GENERAL........................................................................ 8
2. DISASSEMBLY
2-1. 3D Speaker Box Removal ....................................... 27
2-2. Rear Cover Removal................................................ 27
2-3. Speaker Removal ..................................................... 27
2-4. Chassis Assy Removal ............................................. 27
2-5. F Bracket Removal .................................................. 28
2-6. Service Position ....................................................... 28
2-7. Replacement of Parts ............................................... 28
2-7-1. Replacement of Control Button ..................................... 28
2-7-2. Replacement of Light Guide .......................................... 28
2-8. D1 Board Removal .................................................. 29
2-9. PWB Holder Removal ............................................. 29
2-10. Terminal Bracket Removal ...................................... 29
2-11. H3 Board Removal .................................................. 29
2-12. P1 Board Removal ................................................... 30
2-13. A and B3 Boards Removal ...................................... 30
2-14. Picture Tube Removal.............................................. 30
Section Title Page
5. DIAGRAMS
5-1. Block Diagram ......................................................... 47
5-2. Frame Schematic Diagram ...................................... 51
5-3 Circuit Boards Location .......................................... 55
5-4. Schematic Diagrams and Printed Wiring Boards ... 56
(1) Schematic Diagram of A (1/2) Board...................... 59
(2) Schematic Diagram of A (2/2) Board...................... 63
(3) Schematic Diagrams of F and J2 Boards ................... 67
(4) Schematic Diagram of B3 Board ............................ 71
(5) Schematic Diagram of C Board .............................. 79
(6) Schematic Diagram of P1 Board ............................. 83
(7) Schematic Diagrams of B2 and H3 Boards ............ 86
(8) Schematic Diagram VM1 Board ............................. 91
(9) Schematic Diagram D2 Board................................. 93
5-5. Semiconductors........................................................ 90
6. EXPLODED VIEWS
6-1. Speaker Bracket ...................................................... 99
6-2. Chassis .................................................................... 100
6-3. Picture Tube ............................................................ 101
6-4. 3D Speaker.............................................................. 102
3. SET-UP ADJUSTMENTS
3-1. Beam Landing .......................................................... 32
3-2. Convergence............................................................. 33
3-3. Focus Adjustment .................................................... 35
3-4. G2 (Screen) and White Balance Adjustments ......... 36
4. CIRCUIT ADJUSTMENT
4-1. Adjustments with Commander ................................ 37
4-2. Adjustment Method ................................................. 38
4-3. Picture Quality Adjustments.................................... 43
4-4. Display Position Adjustment................................... 43
4-5. A Board Adjustment After IC003 (Memory)
Replacement............................................................. 43
4-6. Picture Distortion Adjustment................................. 44
7. ELECTRICAL PARTS LIST...................................... 103
– 3 –
KV-XF29M97/XF29M67
RM-953

SELF DIAGNOSTIC FUNCTION

The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICAT ORS
When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.
Diagnostic
Item
Description
• Power does not turn on
• +B overcurrent (OCP) or overvoltage (OVP)
• Vertical deflection stopped
• Horizontal deflection overdrive
• White balance failure (no PICTURE)
• Micro reset
No. of times
STANDBY/TIMER
lamp flashes
Does not light
2 times
5 times
Self-diagnostic
display/Diagnostic
result
002:000 or 002:001~255 003:001~255 004:001~255
at the same time
005:000 or 005:001~225
101:00 or
101:001~225
Probable
Cause
Location
• Power cord is not plugged in.
• Fuse is burned out F4601 (F)
• H.OUT Q511 is shorted. (A board)
• IC701 is shorted. (C board)
• -13V is not supplied. (A board)
• IC 503 faulty (A board)
• G2 is improperly adjusted. (Note 2)
• CRT problem.
• Video OUT IC701 is faulty. (C board)
• IC301 is faulty. (A board)
• No connection A board to C board.
• Discharge CRT (C Board)
• Static discharge
• External noise
Detected
Symptoms
• Power does not come on.
• No power is supplied to the TV.
• AC power supply is faulty.
• Power does not come on.
• Load on power line is shorted.
• Has entered standby state after horizontal raster.
• Vertical deflection pulse is stopped.
• Power line is shorted or power supply is stopped.
• No raster is generated.
• CRT cathode current detection reference pulse output is small.
• Power is shut down shortly, after this return back to normal.
• Detect Micro latch up.
Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.
The symptom that is diagnosed first by the microcontroller is displayed on the screen.
Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.
– 4 –
2. DISPLA Y OF STANDBY/TIMER LIGHT FLASH COUNT
2 times
5 times
KV-XF29M97/XF29M67
RM-953
Lamp ON 0.3 sec. Lamp OFF 0.3 sec.
Lamp OFF 3 sec.
STANDBY/SLEEP lamp
Diagnostic Item Flash Count* +B overcurrent/overvoltage 2 times Vertical deflection stopped
White balance failure 5 times * One flash count is not used for self-diagnostic.
3. STOPPING THE STANDBY/TIMER FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp from flashing.
– 5 –
KV-XF29M97/XF29M67
RM-953
4. SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as power sometimes shuts off” or screen sometimes goes out that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screendisplay] / channel [5] / Sound volume [-] / Power ON
˘
Note that this differs from entering the service mode (mode volume [+]).
Self-Diagnosis screen display
SELF DIAGNOSTIC
002 : 000 003 : 000 004 : 000 005 : 001
101 : 000
Numeral "0" means that no fault has been detected.
Numeral "I" means a fault has been detected.
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic screen is being displayed.
Channel [8] / 0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
– 6 –
6. SELF-DIAGNOSTIC CIRCUIT
KV-XF29M97/XF29M67
RM-953
FROM
[+B] Q604 C
[V] Q509/507
[+BovercurrentªOCPº]
FROM
CRT
IC301
Y/CHROMA JUNGLE
IK-IN
MP/
18 51
PROTECT
SDA
Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
4635
IC001
SYSTEM
IO-8DAT
O-LED
IO-SDAT
MEMORY
B-DAT
54521
IC003
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven verticals in a period, the unit will automatically turn off.
[Verticaldeflectionstopped] Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.
[Verticaldeflectionovercurrent] Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.
[Whitebalancefailure] If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301. TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
– 7 –
KV-XF29M97/XF29M67
2
To prevent fire or shock hazard, do not expose the TV to rain or moisture.
Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only.
Do not open the cabinet and the rear cover of the TV. Refer servicing to qualified personnel.
Do not install the TV in hot, humid or excessively dusty places.
Do not install the TV in a confined space, such as a bookcase or built-in cabinet. Do not block the ventilation openings of the TV.
Do not pull the power cord to disconnect the TV. Pull it out by the plug.
Disconnect the power cord if you are not going to use the TV for several days.
Install the TV in a stable position. Do not allow children to climb onto it.
Do not plug in too many appliances to the same power socket. Do not damage the power cord.
Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not scratch the picture tube.
WARNING
• Dangerously high voltages are present inside the TV.
• TV operating voltage: 110 – 240 V AC.
4
Using Your New TV
Getting Started
Step 1
Connect the antenna
If you wish to connect a VCR, see the
Connecting a VCR
diagram below
.
CAUTION
Do not connect the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.
Connecting a VCR
To watch the video, press
(see page 10).
Using Your New TV
IEC connector (not supplied)
To video and audio outputs
VCR
(yellow)
-L (MONO) (white)
-R (red)
To S video output
Antenna cable (not supplied)
To 1, 2 or 3 (video input)
Audio/Video cable (not supplied)
S video cable (not supplied)
: Signal flow
To (S video input)
To antenna output
To ˘ (antenna)
or
: Signal flow
Antenna cable (not supplied)
Antenna cable (not supplied)
Rear of TV
Rear of TV
VIDEO
VIDEO IN
VIDEO OUT
AUDIO
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
– 8 –
SECTION 1

GENERAL

RM-953
5
Using Your New TV
Using Your New TV
1
2
Front of TV
Notes
If you connect a monaural VCR, connect the yellow plug to
(the yellow
jack) and the black plug to
-L (MONO) (the white jack).
If you connect a VCR to the ˘ (antenna) terminal, preset the signal output from the VCR to the program number 0 on the TV.
If both
(S video input) and 1 (video input) at the rear of your TV
are input at the same time, the
(S video input) is automatically
selected. To view 1 (video input), disconnect the S video cable.
Do not connect video equipment to … 3 (video input) at the front and the rear of your TV at the same time; otherwise the picture will not be displayed properly on the screen.
When no signal is input to the connected video equipment, the TV screen becomes blue.
Step 2
Insert the batteries into the remote
Note
Do not use old batteries nor use different types of batteries together.
Step 3
Preset the channels automatically
Tip
If you want to stop the automatic channel presetting, press MENU twice.
Now You Are Ready. . .
To watch your TV, see page 9.
AUTO
PROGR
1
ONE-PUSH AUTOMATIC PROGRAMMING
ONE-PUSH AUTO
MATIC PROGRAMM
ING
AUTO PROGRAM
TV SYS:AUTO
VHF LOW
PR:01
PROGR
6
Using Your New TV
Connecting the 3D WOOFER
3D WOOFER
Black wire
Red wire
1
2
1
Attach the 3D WOOFER into the footholds on the top of your TV.
2
Connect the wires to the 3D WOOFER (8 ) terminals at the rear of your TV. The red wire should be connected to the red terminal and the black wire to the black terminal.
Notes
Connect only the supplied 3D WOOFER; otherwise your TV may malfunction.
Unplug your TV from the wall outlet when connecting the 3D WOOFER.
To prevent a malfunction caused by a short circuit of the terminals, make
sure that none of the 3D WOOFER wire strands stick out, making contact with the neighbouring speaker terminal.
You can enjoy high quality sound by connecting the 3D WOOFER.
Rear of TV
9
KV-XF29M97/XF29M67
RM-953
8
Using Your New TV
Securing the TV
To prevent the TV from falling, secure the TV using one of the following methods:
A
With the supplied screws, attach the band to the TV stand and to the rear of the TV using the provided hole.
or
B
Put the cord or chain through the clamps to secure the TV against a wall or pillar.
Note
Use only the supplied screws. Use of other screws may damage the TV.
20 mm
A
B
3.8 mm
or
7
Using Your New TV
Using Your New TV
Connecting optional components
You can connect optional audio/video components, such as a VCR, multi disc player, camcorder, video game or stereo system.
To watch the picture of the connected equipment, press (see page 10).
Connecting a camcorder/video game equipment using the (video input) jacks
Notes
You can also connect video equipment to the … 1, 2 or 3 (video input) jacks at the rear of your TV.
If both (S video input) and … 3 (video input) at the front of your TV are input at the same time, the
(S video input) is automatically
selected. To view 3 (video input), disconnect the S video cable.
Connecting audio/video equipment using the Ú (monitor output) jacks
Note
When connecting a monaural VCR, connect the yellow plug to
(the
yellow jack) and the black plug to
-L (MONO) (the white jack).
To S video output
Front of TV
Camcorder
Video game equipment
To video and audio outputs
(yellow)
-L (MONO)
(white)
-R (red)
Rear of TV
To antenna output
To video and audio inputs
or
Audio system
To audio inputs
VCR
: Signal flow
: Signal flow
To (S video input)
To
3 (video input)
To Ú (monitor output)
or
Audio/Video cable (not supplied)
S video cable (not supplied)
Antenna cable (not supplied)
Audio/Video cable (not supplied)
or
3
(
MONO
)
– 10 –
KV-XF29M97/XF29M67
RM-953
9
Using Your New TV
Using Your New TV
Watching the TV
This section explains functions used while watching TV. Most operations can be done using the remote.
1
Press U to turn on the TV.
When the TV is in the standby mode (the u indicator on the TV is lit red), press u on the remote or PROGR +/– on the TV
.
2
Press PROGR +/– or number buttons to select the TV program.
For double digit numbers, press ÷, then the number (e.g., for 25, press ÷, then 2 and 5).
3
Press
. +/– to adjust the
volume.
¤
u … ;
Number buttons
JUMP
. +/–
PROGR +/–
continued
MENU
V
/
b
/
v
/
B
/ENTER
or
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
PIC
MODE
SOUND
MODE
SURROUND
1
2
3
4
5
6
7
8 0
-/--
9
PROGR
10
Using Your New TV
To
Turn off temporarily Turn off completely Mute the sound Watch the video input
(VCR, camcorder, etc.)
Jump back to the previous channel Display the on-screen information*
* The picture, sound, and either the program number or video mode are
displayed. The on-screen display for the picture and sound information disappears after about 3 seconds.
Changing the menu language
You can change the menu language as well as the on-screen language. For details on how to use the menu, see
How to use the menu
on page 21.
1
Press MENU.
2
Press V or v to select the SET UP icon (
), then
press ENTER.
3
Make sure LANGUAGE/
is selected, then press ENTER.
4
Press V or v to select
, then press
ENTER. The menu language changes to Arabic.
Do this
Press u. The u indicator on the TV lights up red. Press U on the TV. Press ¤. Press to select VIDEO 1, VIDEO 2 and
VIDEO 3. To return to the TV program, press ;.
Press JUMP. Press
.
Additional tasks
Watching the TV (continued)
To return to the normal screen
Press MENU.
MENU
PICTURE MODE : DYNAMIC SOUND MODE :
DYNAMIC
SURROUND : OFF
A/V CONTROL
LANGUAGE/ : ENGLISH
CHILD LOCK : PR01 OFF PIC ROTATION FAVORITE CH INTELLIGENT VOL : ON
SET UP
LANGUAGE/ :
LANGUAGE : ENGLISH CHILD LOCK PIC ROTATI FAVORITE C INTELLIGEN
SET UP
– 11 –
KV-XF29M97/XF29M67
RM-953
12
Advanced Operations
SOUND MODE
Advanced Operations
PIC MODE
Selecting the picture and sound modes
You can select picture and sound modes and adjust the setting to your preference in PERSONAL option.
Selecting the picture mode
Press PIC MODE repeatedly until you get the desired picture mode.
Select To
DYNAMIC receive high contrast pictures. STANDARD receive normal contrast pictures. SOFT receive mild pictures. PERSONAL receive the last adjusted picture setting from the ADJUST
option in the A/V CONTROL menu (see page 22 and 23).
Selecting the sound mode
Press SOUND MODE repeatedly until you get the desired sound mode.
Select To
DYNAMIC listen to dynamic and clear sound that emphasizes the low and
high tones. DRAMA listen to sound that emphasizes voice and high tones. SOFT receive soft sound. PERSONAL receive the last adjusted sound setting from the ADJUST option
in the A/V CONTROL menu (see page 22 and 23).
Tip
You can also set the picture and sound modes using the menu (seeChanging the A/V CONTROL setting on page 22 and 23).
PERSONAL
SOFT
STANDARD
DYNAMIC
PIC MODE
DYNAMIC
DRAMA
SOFT
PERSONAL
SOUND MODE
11
Using Your New TV
Using Your New TV
Setting the Wake Up timer
1
Press
until the desired period of time appears.
The Wake Up timer starts immediately after you have set it.
2
Select the TV program or video mode you want to display when you wake up.
3
Press u or set the Sleep timer if you want the TV to turn off automatically.
The
indicator lights up orange.
To cancel the Wake Up timer
Press
until WAKE UP TIMER: OFF appears or turn off the
TVs main power.
Note
If no buttons or controls are pressed for more than two hours after the TV is turned on using the Wake Up timer, the TV automatically goes into the standby mode. To continue watching the TV, press any button or control on the TV or the remote.
Setting the Sleep timer
Press
until the desired period of time appears.
The Sleep timer starts immediately after you have set it.
To cancel the Sleep timer
Press
until SLEEP TIMER: OFF appears or turn the TV off.
WAKE UP TIMER:10M
WAKE UP TIMER:OFF
WAKE UP TIMER:12H00M
After 10 minutes
No Wake Up Timer After 12 hours
SLEEP TIMER:30M
SLEEP TIMER:60M
SLEEP TIMER:OFF
SLEEP TIMER:90M
After 30 minutes
No Sleep Timer
After 60 minutes
After 90 minutes
12
KV-XF29M97/XF29M67
RM-953
13
Advanced Operations
1
Press FAVORITE.
2
Press the number button from 1 to 6 to select the desired channel.
Tip
To program your favorite channels, see
Pr
ogramming your favorite
channels on page 26.
Viewing your favorite channels
You can display and select six of your favorite channels directly from your TV screen.
Number buttons
FAVORITE
Advanced Operations
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
FAVORITE CH
. PR01 PR02 PR03
. PR04 PR05 PR06
1
1
2
3
4
5
6
FA
FAVORITE
14
Advanced Operations
Watching two programs at the same time
—PIP
With the Picture-in-Picture (PIP) feature, you can display a different TV program or video directly within the main picture.
Displaying the PIP screen
Press
.
/
/
/
V/v/ENTER
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
PIC
MODE
SOUND
MODE
SURROUND
13
KV-XF29M97/XF29M67
RM-953
15
Advanced Operations
Additional PIP tasks
To
change a TV program in the PIP screen change a video input in the PIP screen swap pictures between the main
and PIP screens
freeze the PIP screen
To return to the normal screen
Press
.
Tips
You can also display the PIP screen using the menu (see
Adjusting the
PIP setting on page 24).
You can change the position of the PIP screen (see “Adjusting the PIP setting on page 24).
Notes
When you display a video input on the PIP screen at a faster/slower speed, the picture may be disrupted depending on the VCR type.
If you display different color systems on the PIP screen, the size of the PIP screen may be different and the picture may be disrupted. This does not indicate a malfunction of the TV.
Press
V or v, then press ENTER.
. .
.
To unfreeze the screen, press the
button again.
16
Advanced Operations
Press SURROUND repeatedly until you receive the desired surround sound.
Select To
HIGH listen to sound that spreads out over a large area, giving the feeling
of being at a concert hall. LOW listen to the sound that gives the feeling of being at a live concert. OFF turn off the surround sound.
The surround of your TV is categorized as TruSurround.
TM
is a trademark of SRS Labs, Inc. SRS and the SRS symbol are registered trademarks of SRS Labs, Inc. in the United States and selected foreign countries. SRS and TruSurround are incorporated under license from SRS Labs, Inc. and are protected under United States Patent Nos. 4,748,669 and 4,841,572 with numerous additional issued and pending foreign patents.
SURROUND
Listening with surround sound
The surround feature enables you to enjoy the sound effects of a concert hall or movie
FAVORITE
SOUND
MODE
SURROUND
SURROUND: LOW
SURROUND: HIGH
SURROUND: OFF
SURROUND
14
KV-XF29M97/XF29M67
RM-953
17
Advanced Operations
Broadcasting On-screen display (Selected sound)
NICAM stereo
NICAM bilingual
NICAM monaural
Selecting a stereo or bilingual program
You can enjoy stereo sound or bilingual programs of NICAM and A2 (German) stereo systems.
Press A/B
repeatedly until you receive the sound you want.
The on-screen display changes to show the selected sound and the  indicator on the TV lights up red.
When receiving a NICAM program
A/B
continued
1
2
3
4
5
6
7
8 0
-/--
9
PIC
MODE
A/B
STEREO
NICAM
MONO
(Stereo sound)
(Regular sound)
NICAM
MAIN
MONO
(Main sound)
(Regular sound)
NICAM
SUB
(Sub sound)
NICAM
MAIN
MONO
(Main sound)
(Regular sound)
18
Advanced Operations
Selecting a stereo or bilingual program (continued)
When receiving an A2 (German) program
Notes
If the signal is very weak, the sound becomes monaural automatically.
If the stereo sound is noisy when receiving a NICAM program, selectMONO. The sound becomes monaural, but the noise is reduced.
If the sound is distorted or noisy when receiving a monaural program through the ˘ (antenna) terminal
Press A/B
repeatedly until
MONO appears on the scr
een.
To cancel the monaural sound setting, press A/B
again until
AUTO appears on the screen.
Notes
The MONO or AUT
O setting is memorized for each program
position.
You cannot receive stereo broadcast signal when the TV is in the
MONO
setting. Normally set the TV to
AUT
O.
MONO
AUTO
Broadcasting On-screen display (Selected sound)
A2 (German) stereo
A2 (German) bilingual
STEREO
MONO
(Stereo sound)
(Regular sound)
MAIN
SUB
(Main sound)
(Sub sound)
15
KV-XF29M97/XF29M67
RM-953
19
Adjusting Your Setup (MENU)
Introducing the menu system
The MENU button lets you open a menu and change the settings of your TV. Here's an overview of the menu system.
Level 1 Level 2 Level 3/Function
A/V CONTROL PICTURE MODE Select the picture mode.
DYNAMIC n STANDARD n SOFT n PERSONAL n ADJUST
ADJUST Adjust the PERSONAL option.
PICTURE n COLOR n BRIGHTn HUEn SHARP
SOUND MODE Select the sound mode.
DYNAMIC n DRAMA n SOFT n PERSONAL n ADJUST
ADJUST Adjust the PERSONAL option.
BASSn TREBLE n BALANCEn BBE
*
SURROUND Select the surround mode.
HIGHn LOW n OFF
PIP PIP POSITION Change the position of the PIP screen.
PIP Display a sub screen within the main picture. SWAP Exchange program between main screen and sub
screen.
SET UP LANGUAGE Change the menu language.
ENGLISH -
(Arabic) CHILD LOCK Lock the channel independently. PIC ROTATION Adjust the picture position. FAVORITE CH Program favorite channels. INTELLIGENT VOL Adjust volume automatically.
Return icon
A/V CONTROL icon
PIP icon
CH PRESET icon
Name of the current menu
Menu level 3
Menu level 2
Adjusting Your Setup (MENU)
Menu level 1
SET UP icon
Menu guide icon
Adjusting Your Setup (MENU)
continued
20
Adjusting Your Setup (MENU)
Level 1 Level 2 Level 3/Function
CH PRESET AUTO PROGRAM Preset channels automatically.
MANUAL PROGRAM Preset channels manually. SKIP Skip unwanted or unused program positions. TV SYS Select the TV system.
B/G, I, D/K, M
COL SYS Select the color system.
AUTO n PALn SECAM n NTSC3.58 n NTSC4.43
*
The BBE is manufactured by Sony Corporation under license from BBE Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No. 4,482,866. The word BBE and the BBE symbol are the trademarks of BBE Sound, Inc.
Introducing the menu system (continued)
16
KV-XF29M97/XF29M67
RM-953
21
Adjusting Your Setup (MENU)
How to use the menu
You can use the buttons on the remote and on the TV as well to display the menu and adjust the settings.
1
Press MENU to display the menu.
2
Press V or v to select the desired item.
3
Press ENTER to confirm your option and go to the next menu level.
Other menu operations
To Press
Adjust the setting value V, b, v or B Move to the next/previous menu level* b or B Cancel the menu MENU
Note
If more than 60 seconds elapse between entries, the menu screen automatically disappears.
Tips
If you want to exit from Menu Level 2 to Menu Level 1, press V or v until the return icon (
) is highlighted, then press ENTER.
You can also use the buttons on the TV for menu operations. ¸ +/– works as V or v on the remote and works as ENTER on the remote.
V/b/v/B/ENTER
MENU
Front of TV
0
-/--
FAVORITE
PICTURE MODE : DYNAMIC SOUND MODE :
DYNAMIC
SURROUND : OFF
A/V CONTROL
MENU
CH PRESET
MANUAL PROGRAM SKIP:PR05 ON TV SYS:B/G COL SYS:AUTO
AUTO PROGRAM
CH PRESET
MANUAL PROGRAM SKIP:PR05 ON TV SYS:B/G COL SYS:AUTO
AUTO PROGRAM
PROGR
ONE-PUSH AUTOMATIC PROGRAMMING
22
Adjusting Your Setup (MENU)
V/b/v/B/ENTER
MENU
Changing the A/V CONTROL setting
The A/V CONTROL menu allows you to change the picture and sound settings.
1
Press MENU.
2
Make sure the A/V CONTROL icon (
) is selected, then press ENTER.
3
Press V or v to select either
PICTURE MODE, SOUND MODE, or SURROUND, then press ENTER.
4
Press V or v to select the desired option, then press ENTER.
For Select
PICTURE MODE either DYNAMIC, STANDARD, SOFT, PERSONAL*, or ADJUST. SOUND MODE either DYNAMIC, DRAMA, SOFT, PERSONAL*, or ADJUST.
SURROUND either HIGH, LOW, or OFF.
* When the PERSONAL mode is selected, the last adjusted picture
and sound settings from the ADJUST option are received.
Tip
For details on the options under
PICTURE MODE
”, “SOUND MODE
and SURROUND, see page 12 and 16 r
espectively.
To return to the normal screen
Press MENU.
FAVORITE
A/V CONTROL
SOUND MODE:DYNAMIC SURROUND:OFF
:DYNAMIC
PICTURE MODE
A/V CONTROL
DRAMA
SOFT
ADJUST
PERSONAL
SURROUND:
SOUND MODE
PICTURE MODE
DYNAMIC
– 17 –
KV-XF29M97/XF29M67
RM-953
23
Adjusting Your Setup (MENU)
Adjusting the ADJUST options under PICTURE MODE
1
Press V or v to select the desired item (e.g., COLOR), then press ENTER.
2
Adjust the value according to the following table, then press ENTER.
For Press v/B to Press V/b to
PICTURE decrease picture contrast increase picture contrast COLOR decrease color intensity increase color intensity BRIGHT darken the picture brighten the picture HUE* increase red picture tones increase green picture tones SHARP soften the picture sharpen the picture
* You can adjust HUE for the NTSC color system only.
3
Repeat the above steps to adjust other items.
The adjusted settings will be received when you select PERSONAL.
Adjusting the ADJUST options under SOUND MODE
1
Press V or v to select the desired item (e.g., BALANCE), then press ENTER.
2
Adjust the value according to the following table, then press ENTER.
For Press v/B to Press V/b to
BASS decrease the bass increase the bass TREBLE decrease the treble increase the treble BALANCE increase the left speaker’s volume
increase the right speakers volume
BBE select “HIGH” for higher enhancement of sound clarity;
select LOW for lower enhancement of sound clarity; select OFF to turn off the BBE sound
3
Repeat the above steps to adjust other items.
The adjusted settings will be received when you select PERSONAL.
Tip
For details on the menu system and how to use the menu, refer toIntroducing the menu system
on page 19 and
How to use the menu
on page 21.
COLOR 80
BALANCE 00
24
Adjusting Your Setup (MENU)
MENU
Adjusting the PIP setting
With the Picture-In-Picture (PIP) feature, you can display a sub screen within the main picture of different TV programs or video inputs.
1
Press MENU.
2
Press V or v to select the PIP icon (
), then press
ENTER.
3
Press V or v to select the desired option, then press ENTER.
V/b/v/B/ENTER
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
PIC
MODE
SOUND
MODE
SURROUND
MENU
A/V CONTROL
SOUND MODE:DYNAMIC SURROUND:OFF
:DYNAMIC
PICTURE MODE
PIP
PIP:OFF SWAP
PIP POSITION :
– 18 –
KV-XF29M97/XF29M67
RM-953
25
Adjusting Your Setup (MENU)
Select To
POSITION change the position of the PIP screen.
Press V or v to select the desired position, then press ENTER.
PIP display a sub screen within the main picture.
Press V or v to select ON, then pr
ess ENTER.
To cancel, press
or select PIP : OFF, then press ENTER.
SWAP exchange program between main screen and sub-screen.
To return to the normal screen
Press MENU.
Tip
For details on the menu system and how to use the menu, refer toIntroducing the menu system
on page 19 and
How to use the menu
on page 21.
26
Adjusting Your Setup (MENU)
Changing the SET UP setting
The SET UP menu allows you to change the menu language, lock channels, adjust the picture position, program your favorite channels and adjust volume automatically.
Programming your favorite channels
The FAVORITE CH feature enables you to program up to six channels for direct selection.
1
Press MENU.
2
Press V or v to select the SET UP icon (
), then
press ENTER.
3
Press V or v to select FAVORITE CH, then press ENTER twice.
4
Press V or v, or number buttons to program the desired channel (e.g., PR03), then press ENTER.
5
To continue programming other favorite channels, press V or v and then press ENTER. After that, repeat step 4.
To return to the normal screen
Press MENU.
MENU
Number buttons
or
V/b/v/B/ENTER
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
1
2
3
4
5
6
7
8 0
-/--
9
SET UP
CHILD LOCK:PR00 OFF PIC ROTATION FAVORITE CH INTELLIGENT VOL:OFF
LANGUAGE/ :ENGLISH
FAVORITE CH
PR01
PR02 PR05 PR07 PR06
PR04
5
FAVORITE CH
PR03
PR02 PR05 PR07 PR06
PR04
– 19 –
KV-XF29M97/XF29M67
RM-953
27
Adjusting Your Setup (MENU)
Using the CHILD LOCK feature
You can prevent your children from watching certain channels by using the CHILD LOCK feature.
1
Press MENU.
2
Press V or v to select the SET UP icon (
), then
press ENTER.
3
Press
V or v
to select CHILD LOCK, then press ENTER.
4
Press V or v, or number buttons to select the desired channel, then press ENTER.
5
Press V or v to select ON, then press ENTER.
The lock symbol (
)
appears on the screen.
To unlock the channel, select OFF.
6
To continue locking other channels, press ENTER and then repeat step 4 to 5.
To return to the normal screen
Press MENU.
or
continued
1
2
3
4
5
6
7
8 0
-/--
9
SET UP
CHILD LOCK:PR00 OFF PIC ROTATION FAVORITE CH INTELLIGENT VOL:OFF
LANGUAGE/ :
ENGLISH
SET UP
CHILD LOCK PR
00
FAVORITE C ON
PIC ROTATI
LANGUAGE/ :
INTELLIGENT
OFF
SET UP
CHILD LOCK PR06
FAVORITE C ON
PIC ROTATI
LANGUAGE/ :
INTELLIGENT
OFF
SET UP LANGUAGE/ :ENGLISH
CHILD LOCK: PR06
ON PIC ROTATION FAVORITE CH INTELLIGENT VOL:OFF
28
Adjusting Your Setup (MENU)
1
Press MENU.
2
Press V or v to select the SET UP icon (
), then
press ENTER.
3
Press V or v to select the desired option (e.g., INTELLIGENT VOL), then press ENTER.
Select To
LANGUAGE/
Change the menu language (see
Changing the menu
language on page 10).
CHILD LOCK Prevent children from watching certain channels (see
Using the CHILD LOCK feature on page 26).
PIC ROTATION Adjust the picture position when it is not aligned to the
TV screen. Press V, b, v or B to adjust the picture position, then press ENTER.
FAVORITE CH Program channels for direct selection (see
Pr
ogramming
your favorite channels
on page 25).
INTELLIGENT VOL Adjust the volume of each program automatically.
Press V or v to select ON, then pr
ess ENTER.
To turn off the Intelligent Volume function, select
OFF,
then press ENTER.
To return to the normal screen
Press MENU.
Tip
For details on the menu system and how to use the menu, refer toIntroducing the menu system
on page 19 and
How to use the menu
on page 21.
Changing other SET UP menu options
Changing the SET UP setting (continued)
SET UP
CHILD LOCK:PR00 OFF PIC ROTATION FAVORITE CH INTELLIGENT VOL:OFF
LANGUAGE/ :
ENGLISH
SET UP
CHILD LOCK OFF
FAVORITE C
PIC ROTATI
INTELLIGENT VOL
LANGUAGE/ :
ON
PIC ROTATION
20
KV-XF29M97/XF29M67
RM-953
29
Adjusting Your Setup (MENU)
Changing the Channel Preset (CH PRESET) setting
The CH PRESET menu allows you to adjust the setup of your TV. For example, you can receive a channel with a weak signal that fails to be tuned in by automatic presetting.
Presetting channels manually
1
Press MENU.
2
Press V or v to select the CH PRESET icon (
),
then press ENTER.
3
Press V or v to select MANUAL PROGRAM, then press ENTER.
4
Select the program number to which you want to preset a channel.
(1) Make sure “PR” is
selected , then press ENTER.
(2) Press V or v until the
program number you want to preset (e.g., program number 10) appears on the menu, then press ENTER.
V/b/v/B/ENTER
MENU
continued
FAVORITE
SOUND MODE
SURROUND
CH PRESET
MANUAL PROGRAM SKIP:PR05 ON TV SYS:B/G
COL SYS:AUTO
AUTO PROGRAM
MANUAL PROGRAM
TV SYS:B/G
VHF LOW FINE:AUTO
PR: 01
SENS:HIGH
PR: 01
MANUAL PROGRAM
TV SYS:B/G
VHF LOW FINE:AUTO
SENS:HIGH
MANUAL PROGRAM
TV SYS:B/G
VHF LOW FINE:AUTO
PR:10
SENS:HIGH
30
Adjusting Your Setup (MENU)
Changing the Channel Preset (CH PRESET) setting (continued)
5
Select the desired channel.
(1) Press V or v to select
either VHF LOW, VHF HIGH or UHF, then press ENTER.
(2) Press V or v until the
desired channel picture appears on the TV screen, then press ENTER.
6
If the sound of the desired channel is abnormal, select the appropriate TV system.
(1) Press V or v to select
TV SYS, then press ENTER.
(2) Press V or v until the
sound becomes normal (e.g., M), then press ENTER.
MANUAL PROGRAM
TV SYS:B/G
VHF LOW FINE:AUTO
PR:10
SENS:HIGH
VHF LOW
MANUAL PROGRAM
TV SYS:B/G
FINE:AUTO
PR:10
SENS:HIGH
MANUAL PROGRAM
TV SYS: I
D/K
VHF LOW FINE:AUTO
PR:10 B/G
M
SENS:HIGH
MANUAL PROGRAM
VHF LOW
FINE:AUTO
PR:10
TV SYS: M
SENS:HIGH
– 21 –
KV-XF29M97/XF29M67
RM-953
31
Adjusting Your Setup (MENU)
7
If you are not satisfied with the picture and sound quality, you may improve them by using fine tuning.
(1) Press V or v to select
FINE, then press ENTER.
(2) Press V or v to select
MANUAL, then press ENTER.
(3) Press V, b, v or B until
you are satisfied with the picture and sound quality, then press ENTER.
The + or – icon on the menu flashes while tuning.
8
If the TV signal is too strong and the picture is distorted, you may reduce the TV receiving sensitivity.
(1) Press V or v to select
SENS, then press
ENTER.
(2) Press V or v to select
LOW, then press ENTER.
To return to the normal screen
Press MENU.
Notes
If you preset a locked channel, that particular channel will be unlocked automatically (see page 27).
The TV system (TV SYS),
SENS and the fine tuning (FINE) settings are
memorized for each program number.
continued
MANUAL PROGRAM
TV SYS:M MANUAL
VHF LOW FINE:
PR:02 AUTO
SENS:HIGH
MANUAL PROGRAM
TV SYS:M
VHF LOW FINE:
PR:10
– +
AUTO
MANUAL
SENS: HIG
MANUAL PROGRAM
VHF LOW
FINE: MANUAL
PR:10
TV SYS:M
SENS:HIGH
MANUAL PROGRAM
TV SYS:M LOW
VHF LOW
PR:10 HIGH
SENS:
FINE:AUTO
MANUAL PROGRAM
TV SYS:M
VHF LOW
FINE:AUTO
PR:10
SENS:LOW
32
Adjusting Your Setup (MENU)
Changing other CH PRESET menu options
1
Press MENU.
2
Press V or v to select the CH PRESET icon (
), then
press ENTER.
3
Press V or v to select the desired option (e.g., SKIP), then press ENTER.
Select
AUTO PROGRAM MANUAL PROGRAM
TV SYS
COL SYS SKIP
Tip
For details on the menu system and how to use the menu, refer toIntroducing the menu system
on page 19 and
How to use the menu
on page 21.
Note
If you preset a locked channel, that particular channel will be unlocked automatically.
To
preset channels automatically. preset channels manually. See Presetting channels
manually on page 26 and 27. select the TV system. See
Pr
esetting channels manually
on page 26 and 27. select the color system. Normally, set this to “AUTO”. skip unwanted or unused program numbers.
1 Press V or v until the unused or unwanted program
number appears, then press ENTER.
2 Press V or v to select ON, then pr
ess ENTER.
To put the skipped program number back on, select OFF, then press ENTER.
Changing the Channel Preset (CH PRESET) setting (continued)
CH PRESET
MANUAL PROGRAM SKIP:PR05 ON TV SYS:B/G
COL SYS:AUTO
AUTO PROGRAM
CH PRESET
MANUAL PRO PR
10
SKIP: TV SYS:B/G ON COL SYS:AU OFF
AUTO PROGR
– 22 –
KV-XF29M97/XF29M67
RM-953
33
Additional Information
Additional Information
Self-diagnosis function
Your TV is equipped with a self-diagnosis function. If there is a problem with your TV, the u indicator flashes red. The number of times the u indicator flashes indicates the possible causes.
1
Check that the red flashes of the u indicator is about 3 seconds per interval.
2
Count the number of times the u indicator flashes.
3
Press U (main power) to turn off your TV.
4
Inform your nearest Sony service center about the number of times the u indicator flashes. Be sure to note the model name and serial number located on the rear of your TV.
Front of TV
34
Additional Information
Troubleshooting
If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer.
Possible causeSymptom
Solutions
Check the antenna cable and connection on the TV, VCR and on the wall. (page 4)
Display the CH PRESET menu and
select MANUAL PROGRAM to preset the channel again. (page 29 and 30)
Check the antenna type (VHF/UHF).
Contact a Sony dealer for advice.
Adjust the antenna direction. Contact a
Sony dealer for advice.
Try using a booster.
Display the CH PRESET menu and select MANUAL PROGRAM
. Then,
select
SENS: ON. (page 22)
Turn off or disconnect the booster if it is in use.
If the sound of all the channels are noisy, display the CH PRESET menu and select the appropriate TV system (page 30), then select “AUTO PROGRAM to preset the channels again. (page 32)
If the sound of some channels are noisy, select the channel, then display the CH PRESET menu and select the appropriate TV system. (page 30)
Check the power cord, antenna and the VCR connections.
Press u (power).
Press U (main power) on the TV to turn
off the TV about five seconds, then turn it on again.
Connection is loose or the cable is damaged.
Channel presetting is inappropriate or incomplete.
The antenna type is inappropriate.
The antenna direction is inappropriate.
Signal transmission is low.
Broadcast signals are too
strong.
The TV system setting is inappropriate.
The power cord, antenna or VCR is not connected.
The TV is not turned on.
Snowy picture
Noisy sound
Distorted picture
Noisy sound
Good picture
Noisy sound
No picture
No sound
23
KV-XF29M97/XF29M67
RM-953
KV-XF29M97/XF29M67
35
Additional Information
Additional Information
Press ¸ + to increase the volume level.
Press ¤ to cancel the muting.
Press A/B
until a good sound is
heard.
Do not use a hair dryer or other equipment near the TV.
Adjust the antenna direction for minimum interference. Contact a Sony dealer for advice.
Use a highly directional antenna.
Adjust the antenna direction. Contact a
Sony dealer for advice.
Turn off or disconnect the booster if it is in use.
Display the A/V CONTROL menu and select ADJUST of PICTURE MODE, then adjust the COLOR level. (page 22 and 23)
Display the CH PRESET menu and check the color system (COL SYS) setting (usually set this to AUTO). (page 32)
Adjust the antenna direction. Contact a Sony dealer for advice.
Keep external speakers or other electrical equipment away from the TV. Do not move the TV while the TV is turned on. Press U (main power) on the TV to turn off the TV for about five minutes, then turn it on again.
Press A/B
until “AUTO” appears on
the screen.
Good picture
No sound
Dotted lines or stripes
Double images or ghosts
No color
Abnormal color patches
TV cannot receive stereo broadcast signal.
The volume level is too low.
The sound is muted.
Broadcast signal has a
transmission problem.
There is local interference from cars, neon signs, hair dryers, power generators, etc.
Broadcast signals are reflected by nearby mountains or buildings.
The antenna direction is inapproprite.
Use of a booster is inappropriate.
The color level setting is too low.
The color system setting is inappropriate.
The antenna direction is inapproriate.
There are magnetic effects from external speakers or other electrical equipment that may affect the TV.
The direction of the earth
s
magnetic field may affect the TV.
The stereo reception setting is inappropriate.
Possible causeSymptom
Solutions
36
Additional Information
Possible causeSymptom
Solutions
Check the antenna cable and connection on the TV, VCR and on the wall. (page 4)
Adjust the antenna direction. Contact a Sony dealer for advice.
Press A/B
until a good sound is
heard.
Keep external speakers or other electrical equipment away from the TV.
Display the SET UP menu and adjustPIC ROTATION” so that the picture is
aligned to the TV screen. (page 28)
Contact your nearest Sony service center.
Connection is loose or the
cable is damaged.
The antenna direction is inappropriate.
Broadcast signal has a transmission problem.
The magnetic disturbance from external speakers or other equipment, or the direction of the earth
s magnetic field may affect the TV.
Your TV may need service.
Changes in room
temperature sometimes make the TV cabinet expand or contract, making a noise. This does not indicate a malfunction.
The TVs demagnetizing function is working. This does not indicate a malfunction.
Stereo broadcast sound switches on and off or is distorted.
or
The sound switches between monaural and stereo frequently.
Picture slant
The
u
indicator on your TV flashes red for about 3 seconds per interval.
TV cabinet creaks.
A “boom” sound is heard when the TV is turned on.
RM-953
24
37
Additional Information
Identifying parts and controls
Refer to the pages indicated in parentheses ( ) for details.
Front panel
1
U
(main power) button (9)
2 AUTO PROGR (auto program) button (5) 3 MENU button (21) 4 PROGR +/ (program) buttons (9) 5
¸
+/– (volume) buttons (9)
6
(TV/video) button (10)
7
2
(Headphone) jack
ONE-PUSH AUTOMATIC PROGRAMMING
PROGR
38
Additional Information
1 ¤ (muting) button (10) 2
(display) button (10)
3 PIC MODE button (12) 4 u (power) button (9) 5 A/B button (15) 6 (video) button (10) 7 ; (TV) button (10) 8 Number buttons (10) 9 JUMP button (10)Menu operation buttons (21)
MENU button V/b/v/B buttons
SURROUND button (16) !™ Timer setting buttons (11)
(wake up timer) (sleep timer)
FAVORITE button (13)
Remote Control
SOUND MODE button (12) !∞ . (volume) +/ buttons (9)PROGR +/ button (9)Teletext operation buttons
(not used for KV-XF29M97/ XF29M67/XF25M97/XF25M67)
(text)
yellow
(enlarge)
blue
(reveal) V/b/v/B/ENTER (hold)
(index)
red
(text clear)
green
Button function
For general TV operations For Teletext operations For PIP operations
Names/symbols of buttons on the remote are indicated in different colors to represent the available functions.
Label color
White Green Yellow
5
4
3
6
8
9
!¡ !™
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
PIC
MODE
SOUND MODE
SURROUND
1 2
7
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
PIC
MODE
SOUND
MODE
SURROUND
!∞
25
KV-XF29M97/XF29M67
RM-953
KV-XF29M97/XF29M67
39
Additional Information
!• PIP operation buttons (24-25)
(TV/video) (freeze) (swap) (PIP)
V/v ENTER – for PIP PROGR
1
2
3
4
5
6
7
8 0
-/--
9
FAVORITE
PIC
MODE
SOUND MODE
SURROUND
!•
RM-953
26
Loading...
+ 60 hidden pages