Sony KV-XA51M61, KV-XA21M83, KV-XA21M93, KV-XA21N93, KV-XA21P80 Service Manual

REVISION HISTORY

BG-3R

CHASSIS

MODEL

KV-XA21M83 KV-XA21M93 KV-XA21M83 KV-XA51M61 KV-XA21N93 KV-XA21P80

NO DATE DESCRIPTION OF REVISION

PA RT NO. : 9-872-249-01

SERVICE MANUAL BG-3R

CHASSIS

MODEL COMMANDER DEST. CHASSIS NO.

KV-XA21M83 RM-952 India SCC-U60A-A KV-XA21M93 RM-952 India SCC-U60B-A KV-XA21M83 RM-952 Vietnam SCC-U56D-A KV-XA51M61 RM-952 Indonesia SCC-U59A-A KV-XA21N93 RM-915 Philippines SCC-U61A-A KV-XA21P80 RM-952 ME SCC-U48M-A

MODEL COMMANDER DEST. CHASSIS NO.

POWERTVDISPLAY

MUTING

VIDEO

MTS

ENT

JUMP

CHVOL

SOUND MODE

FAVORITE

SELECT

WAKE UP

PIC MODE

SLEEP

AUTO

ADD/

CABLE

PROGRAM

ERASE

RM-915

JUMP

SOUND

PROGRÁ

MODE

FAVORITE

RM-952

TRINITRON

COLOR TV

KV-XA21M83/XA21M93/XA51M61/XA21P80

RM-952

KV-XA21N93

RM-915

Power requirements 110-240 V AC, 50/60 Hz

Power consumption (W) Indicated on the rear of the TV

Television system B/G KV-XA21P80

M KV-XA21N93

Color system PAL, PAL 60, NTSC4.43, NTSC3.58 (AV IN) KV-XA21P80

NTSC3.58, PAL*, PAL 60*, SECAM*, NTSC4.43* *AV IN only KV-XA21N93

Stereo/Bilingual system MTS KV-XA21N93

Channel coverage

B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41 KV-XA21P80

M VHF: 2 to 13 / UHF: 14 to 69 / CATV: 1 to 125 KV-XA21N93

˘˘

˘ (Antenna) 75-ohm external terminal

˘˘

Audio output (speaker) 5W + 5W KV-XA21P80

3W + 3W KV-XA21N93

3D Woofer 9W KV-XA21N93 only

Number of terminal

D (Video) Input: 2 Output: 1 ≥ Audio Input: 2 Output: 1 Phono jacks; 500 mVrms 2 (Headphone) Output: 1 Stereo minijack

Picture tube 21 inch

Tube size (cm) 54 Measured diagonally

Screen size (cm) 51 Measured diagonally

Dimension (w/h/d, mm) 640 × 452 × 496 KV-XA21P80

640 × 482 × 496 KV-XA21N93

Mass (kg) 26 KV-XA21P80

28 KV-XA21N93

SPECIFICATIONS

(KV-XA21P80/XA21N93)

Note

Phono jacks; 1 V

P-P

, 75 ohms

CAUTION

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.

Design and specifications are subject to change without notice.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

– 2 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

KV-XA21N93

SPECIFICATIONS

(Except KV-XA21P80/XA21N93 )

Note

Power requirements 110-240 V AC, 50/60 Hz

Power consumption (W) Indicated on the rear of the TV

Television system B/G, I, D/K, M

Color system PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58

Stereo/Bilingual system Nicam Stereo/ Bilingual B/G, I, D/K; A2 Stereo/Bilingual B/G KV-XA21M93/XA51M61

Teletext language English, Arabic, French KV-XA51M61 only

Channel coverage

B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41

I UHF: B21 to B68 / CATV: S01 to S03, S1 to S41

D/K VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60 /

CATV: S01 to S03, S1 to S41, Z1 to Z39

M VHF: A2 to A13 / UHF: A14 to A79 /

CATV: A-8 to A-2, A to W+4, W+6 to W+84

˘˘

˘ (Antenna) 75-ohm external terminal

˘˘

Audio output (speaker) 3W + 3W except KV-XA51M61

5W + 5W KV-XA51M61 only

3D WOOFER 9W except KV-XA51M61

Number of terminal

D (Video) Input: 2 Output: 1 ≥ Audio Input: 2 Output: 1 Phono jacks; 500 mVrms 2 (Headphone) Output: 1 Stereo minijack

Picture tube 21 inch Except KV-XA51M61

Tube size (cm) 54 Measured diagonally

Screen size (cm) 51 Measured diagonally

Picture tube KV-XA51M61

Tube size (mm) 545 Measured diagonally

Screen size (mm) 507 Measured diagonally

Dimension (w/h/d, mm) 620 × 482 × 496 except KV-XA51M61

620 x 452 x 496 KV-XA51M61

Mass (kg) 26 KV-XA51M61

28 except KV-XA51M61

Phono jacks; 1 VP-P, 75 ohms

RM-952

RM-915

CAUTION

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.

Design and specifications are subject to change without notice.

SAFETY-RELATED COMPONENT WARNING!!

– 3 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

RM-952

KV-XA21N93

RM-915

Section Title Page Section Title Page

SELF DIAGNOSTIC FUNCTION ..................... 5

1. GENERAL ........................................................ 8

2. DISASSEMBLY

2-1. 3D Speaker Box Removal ....................................... 36

2-2. Rear Cover Removal ............................................... 36

2-3. Speaker Removal .................................................... 36

2-4. Chassis Assy Removal ............................................ 36

2-5. F, H4 and K2 Boards Removal ............................... 36

2-6. J3 Board and Terminal Bracket Removal ............... 36

2-7. Service Position ...................................................... 37

2-8. Replacement Of Part ............................................... 37

2-8-2. Power Button ................................................ 37

2-8-1. Light Guide .................................................. 37

2-9. Picture Tube Removal ............................................. 37

3. SET-UP ADJUSTMENTS

3-1. Beam Lading ........................................................... 39

3-2. Convergence Adjusment ......................................... 40

3-3. Focus Adjustment .................................................... 42

3-4. G2 (Screen) and White Balance Adjustement ........ 42

4. CIRCUIT ADJUSTMENTS

4-1. Adjustment with Commander ................................. 43

4-2. Adjustment Method ................................................ 43

4-3. Picture Quality Adjustment .................................... 49

4-4. Deflection Adjustment ............................................ 49

4-5. A Board Ajustment After IC003 (memory)

Replacement ............................................................ 49

4-6. Picture Distortion Adjustment ................................ 50

5. DIAGRAMS

5-1. Block Diagram ......................................................... 51

5-2. Circuit Board Location ............................................ 52

5-3. Schematic Diagrams................................................. 52

(1) Schematic Diagrams of F, J3 and H4 Boards ... 55

(2) Schematic Diagram of A Board ....................... 56

(3) Schematic Diagram of C1 Board ...................... 73

(4) Schematic Diagrams of K2 and V1 Boards..... 75

Board Mark List ...................................................... 77

5-4. Voltage Measurements ............................................. 80

5-5. Waveforms ................................................................ 82

5-6. Printed Wiring Boards and Parts Location .............. 83

5-7. Semiconductors ........................................................ 91

6. EXPLODED VIEWS

6-1. Picture Tube.............................................................. 93

6-2. Chassis ...................................................................... 95

7. ELECTRICAL PARTS LIST ........................... 97

– 4 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

KV-XA21N93

SELF DIAGNOSTIC FUNCTION

The units in this manual contain a self-diagnostic function. If an error occurs, the STANBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANBY/ TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.

1. DIAGNOSTIC TEST INDICATORS

When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the problem. If there is more than one error, the lamp will identify the first of the problem areas.

Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.

Diagnostic

Item

Description

• Power does not turn on

No. of times

STANDBY/TIMER

lamp flashes

Does not light

Self-diagnostic

display/Diagnostic

result

—

Probable

Cause

Location

• Power cord is not plugged in.

• Fuse is burned out F4601 (F)

Detected

Symptoms

• Power does not come on.

• No power is supplied to the TV.

• AC power supply is faulty.

RM-952

RM-915

• +B overcurrent (OCP) or overvoltage (OVP)

• Vertical deflection stopped

• Horizontal deflection overdrive

• White balance failure (no PICTURE)

• Micro reset

2 times

5 times

—

002:000 or 002:001~255 003:001~255 004:001~255

at the same time

005:000 or 005:001~225

101:00 or

101:001~225

• H.OUT Q511 is shorted. (A board)

• IC700 is shorted (C1 board)

• -13V is not supplied. (A board)

• IC 503 faulty (A board)

• G2 is improperly adjusted. (Note 2)

• CRT problem.

• IC700 out is faulty (C1 board)

• IC301 is faulty. (A board)

• No connection A board to C1 board.

• Discharge CRT (C1 Board)

• Static discharge

• External noise

• Power does not come on.

• Load on power line is shorted.

• Has entered standby state after horizontal raster.

• Vertical deflection pulse is stopped.

• Power line is shorted or power supply is stopped.

• No raster is generated.

• CRT cathode current detection reference pulse output is small.

• Power is shut down shortly, after this return back to normal.

• Detect Micro latch up.

Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.

The symptom that is diagnosed first by the microcontroller is displayed on the screen.

Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.

*IC700 out is faulty (C1 board).

– 5 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

RM-952

KV-XA21N93

RM-915

2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT

2 times

3 times

Diagnostic Item Flash Count*

+B overcurrent/overvoltage 2 times Vertical deflection stopped

White balance failure 5 times

Lamp ON 0.3 sec.

Lamp OFF 0.3 sec.

Lamp OFF 3 sec.

* One flash count is not used for self-diagnostic.

STANDBY/SLEEP lamp

3. STOPPING THE STANDBT/TIMER FLASH

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp from flashing.

4. SELF-DIAGNOSTIC SCREEN DIPLAY

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen:

[To Bring Up Screen Test]

In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:

[Screendisplay] / channel [5] / Sound volume [-] / Power ON

Note that this differs from entering the service mode (mode volume [+]).

Self-Diagnosis screen display

SELF DIAGNOSTIC

002 : 000 003 : 000 004 : 000 005 : 001

101 : 000

Numeral "0" means that no fault has been detected.

Numeral "1" means a fault has been detected.

– 6 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

KV-XA21N93

5. HANDLINGOF SELF-DIAGNOSTIC SCREEN DISPLAY

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”.

Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.

[Clearing the result display]

To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic screen is being displayed.

Channel [8] / 0

[Quitting Self-diagnostic screen]

To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.

RM-952

RM-915

6. SELF-DIAGNOSTIC CIRCUIT

IC301

Y/CHROMA JUNGLE

FROM

CRT

FROM

[+B] Q604 C6

[V] Q509/507

IK-IN

MP/

PROTECT

SDA

[+BovercurrentªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to

ON and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven verticals in a period, the unit will automatically turn off.

IC001

SYSTEM

IO-8DAT B-DAT

O-LED

IO-SDAT

IC003

MEMORY

521

[Verticaldeflectionstopped] Occurs when an absence of the vertical deflection pulse is detected by Q509 and

IC001 shut down the power supply.

[Verticaldeflectionovercurrent] Occurs when an overcurrent on V drive line is detected by Q507. Power supply will

be shut down when detect this by IC001.

[Whitebalancefailure] If the RGB levels* do not balance or become low level within 5 seconds, this error

will be detected by IC301. TV will stay on, but there will be no picture.

* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)

– 7 –

The operating instruction mentioned here are partial abstracts

WARNING

• Dangerously high voltages are present inside the TV.

• Operate the TV only between 110 – 240 V AC.

To prevent fire or shock hazard, do not expose the TV to rain or moisture.

Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only.

Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel.

Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations.

Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet.

For children’s safety, do not leave children alone with the TV. Do not allow children to climb onto it.

Do not plug in too many appliances to the same power socket. Do not damage the power cord.

Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not scratch the picture tube.

For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms.

Pull the power cord out by the plug. Do not pull the power cord itself. Disconnect the TV before moving it or if you are not going to use it for several days.

Using Your New TV

Getting Started

Step 1

Connect the antenna

If you wish to connect a VCR, see the Connecting a VCR diagram below.

Using Your New TV

IEC connector (not supplied)

To video and audio outputs

(yellow)

-L (MONO) (white)

-R (red)

Audio/Video cable (not supplied)

Rear of TV

Connecting a VCR

To watch the video input, press t (see page 13).

: Signal flow

Antenna cable (not supplied)

To t 1 (video input)

Antenna cable (not supplied)

To antenna output

VCR

Rear of TV

VIDEO

VIDEO IN

VIDEO OUT

AUDIO

L(MONO)

To 8 (antenna)

from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.

KV-XA21M83/XA21M93/XA51M61/XA21P80

SECTION 1-2

GENERAL

(except KV-XA21N93)

– 8 –

KV-XA21N93

RM-952

RM-915

Using Your New TV

Step 2

Note

• Do not use old batteries nor use different types of batteries together.

Front of TV

Notes

• If you connect a monaural VCR, connect the yellow plug to

(the

yellow jack) and the black plug to

-L (MONO) (the white jack).

• If you connect a VCR to the 8 (antenna) terminal, preset the signal

output from the VCR to the program number 0 on the TV.

• When no signal is input from the connected video equipment, the TV screen becomes blue.

CAUTION

• Do not connect the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid that leaks from the batteries touches you, immediately wash it away with water.

Insert the batteries into the remote

Step 3

Preset the channels automatically

Tips

• If you want to stop automatic channel presetting, press SELECT twice.

• If your TV has preset an unwanted channel or cannot preset a particular

channel, then preset your TV manually (see page 10).

Note (except KV-XA21P80/XA51M61)

• During automatic channel presetting, your TV screen will indicate “B/G” , “I”, “D/K” or “M” for the TV system.

AUTO

PROGR

VHF LOW B/G

L(MONO) R

PROGR

SELECT

AUTO PROGR

Using Your New TV

Connecting the 3D WOOFER

(except KV-XA21P80/XA51M61)

You can enjoy high quality sound by connecting the 3D WOOFER.

Align the front of the 3D WOOFER to corners A and B of your TV. Place the 3D WOOFER into the footholds and adjust it until it is stable.

Connect the wires to the 3D WOOFER (8Ω) terminals at the rear of your TV. The red wire should be connected to the 3 red terminal and the black wire to the # black terminal.

Notes

• Connect only the supplied 3D WOOFER; otherwise your TV may

malfunction.

• Unplug your TV from the wall outlet when connecting the 3D WOOFER.

• To prevent a malfunction caused by a short circuit of the terminals, make

sure that none of the 3D WOOFER wire strands stick out, making contact with the neighbouring 3D WOOFER terminal.

Black wire

Red wire

WOOFER (8 )

– +

WOOFER (8 )

– +

3D WOOFER

Corner A

Corner B

– 9 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

KV-XA21N93

RM-952

RM-915

Using Your New TV

Connecting optional components

You can connect optional audio/video components, such as a VCR, multi disc player, camcorder, video game or stereo system.

To watch the video input of the connected equipment, press t (see page 13).

Connecting a camcorder/video game equipment using the t (video input) jacks

Note

• You can also connect video equipment to the t 1 (video input) jack at the rear of your TV.

Connecting audio/video equipment using the T (monitor output) jacks

Note

• If you connect a monaural VCR, connect the yellow plug to

(the yellow

jack) and the black plug to

-L (MONO) (the white jack).

(yellow)

-L (MONO)

(white)

-R (red)

Rear of TV

To antenna output

To video and audio inputs

Audio system

To audio inputs

VCR

: Signal flow

To T (monitor output)

Antenna cable (not supplied)

Audio/Video cable (not supplied)

L(MONO)

Front of TV

Camcorder

Video game equipment

To video and audio outputs

: Signal flow

(video input)

Audio/Video cable (not supplied)

(

MONO

)

L(MONO) R

PROGR

SELECT

AUTO PROGR

Using Your New TV

Securing the TV

To prevent the TV from falling, secure the TV using one of the following methods:

With the supplied screws, attach the band to the TV stand and to the rear of the TV using the provided hole.

Put the cord or chain through the clamps to secure the TV against a wall or pillar.

Note

• Use only the supplied screws. Use of other screws may damage the TV.

20 mm

3.8 mm

– 10 –

KV-XA21N93

RM-952

RM-915

KV-XA21M83/XA21M93/XA51M61/XA21P80

Using Your New TV

Presetting channels

You can preset up to 100 TV channels in numerical sequence from program number 1 using the remote and the buttons on your TV as well.

Presetting channels automatically

Press ! to turn on the TV.

Press AUTO PROGR.

Note (except KV-XA21P80/XA51M61)

• During automatic channel presetting, your TV screen will indicate

“B/G” ,

“I”, “D/K” or “M” for the TV system.

To preset channels automatically from a specified program number

(1) Press SELECT until

“AUT

O PROGRAM” appears.

(2) Press + or –.

The on-screen display will start flashing.

(3) Press PROGR +/– or the number buttons until the desir

ed program number

appears.

(4) Press + or –.

Number buttons

SELECT

2 +/–

PROGR +/–

+ or –

PIC MODE

JUMP

SOUND

MODE

FAVORITE

PROGR

VHF

LOW

B/G

AUTO

PROGR

L(MONO) R

PROGR

SELECT

AUTO PROGR

AUTO

PROGR

continued

Using Your New TV

Presetting channels (continued)

Presetting channels manually

Press SELECT until “MANUAL PROGRAM” appears.

Press + or –.

Press PROGR +/– or the number buttons until the desired program number appears.

Press + or – until the desired channel picture appears.

Press SELECT.

Note (except KV-XA21P80)

• If you preset a locked program number, that particular program number

will be unlock automatically (see page 18).

To change the TV system setting

If the picture or sound is abnormal when receiving programs through the

(antenna)

terminal

(1) Press SELECT until

“TV SYS” appears.

(2) Press + or – to select the appropriate

TV system until the picture or sound quality is optimal.

MANUAL PROGRAM

SELECT

VHF

LOW

B/G

-/--

PROGR

SELECT

TV SYS: B/G

B/G

I D/K

– 11 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

KV-XA21N93

RM-952

RM-915

Using Your New TV

To change the color system setting

If the color is abnormal when receiving programs through the

(antenna) terminal

or the

(video input) jack.

(1) Press SELECT until

“COLOR SYS” appears.

(2) Press + or – to select the appropriate

color system until the color is optimal.

Tip

• Normally set “COLOR SYS” to “AUT

O”.

Skipping program numbers

Press PROGR +/

– or the number buttons until the unused or unwanted

program number appears.

Press SELECT until

“MANUAL PROGRAM

” appears.

Press + or –.

Press PIC MODE.

Press SELECT.

To restore the skipped program number again

Preset the channel automatically or manually.

Tip

• You can also use SELECT and

+/– on the TV to preset channels and

skip program numbers.

To use the fine tuning (FINE) function

The fine tuning (FINE) function may help to reduce the following problems: double images and lines moving across the TV screen.

You can use the fine tuning function as below: (1) Select the program number you want to adjust.

(2) Press SELECT until

“MANUAL

PROGRAM” appears on the screen. (3) Press + or – on the remote control once. (4) Press

to display “FINE” on the scr

een.

(5) Press + or – continuously until the above problems are minimized.

The + or – icon on the screen flashes while tuning.

(6) Press SELECT to return to normal screen.

COLOR SYS: AUTO

AUTO

PAL SECAM

NTSC 3.58NTSC 4.43

Using Your New TV

Watching the TV

This section explains functions used while watching the TV. Most operations can be done using the remote.

Press ! to turn on the TV.

When the TV is in the standby mode (the 1 indicator on the TV is lit red), press

1 on the

remote or PROGR +/

– on

the TV.

Press PROGR +/

– or the number buttons to select the program number.

For double digit numbers, press -, then the number (e.g., for 25, press -, then 2 and 5).

Press 2 +/– to adjust the volume.

indicator

Number buttons

SELECT

2 +/–

PROGR +/–

+ or –

JUMP

L(MONO) R

PROGR

SELECT

AUTO PROGR

PROGR

SELECT

AUTO

PROGR

JUMP

SOUND

MODE

FAVORITE

PROGR

-/--

PROGR

– 12 –

KV-XA21N93

RM-952

RM-915

KV-XA21M83/XA21M93/XA51M61/XA21P80

Using Your New TV

Turn off temporarily

Turn off completely

Mute the sound

Watch the video input (VCR, camcorder, etc.)

Jump back to the previous program number

Display the on-screen information*

Adjust the volume of all program numbers automatically

Adjust the picture position when it is not aligned to the TV screen

Additional tasks

* The picture, sound, and either the program number or video input are

displayed. The on-screen display for the picture and sound information disappears after about three seconds.

Changing the on-screen display language

(KV-XA51M61/XA21M83(Vietnam))

Press SELECT until “LANGUAGE /

: ENGLISH”appears on the screen.

Press + or – to select “

“.

Tip

• You can also use SELECT and 2 +/– on the TV to select the on-screen

display language.

LANGUAGE / : ENGLISH

SELECT

/ LANGUAGE :

continued

PIC ROTATION

Press

1. The 1 indicator on the TV lights up red.

! on the TV.

t to select “VIDEO 1” or “VIDEO 2”. To return to the TV program, press a.

JUMP.

SELECT repeatedly until

“INTELLIGENT VOL

”

appears, then press + or – to select “ON”. To cancel, select “OFF”.

SELECT repeatedly until

“PIC ROT

ATION” appears, then press + or – to adjust the alignment of the picture position.

The

icon on the screen flashes while adjusting.

Using Your New TV

Turn off temporarily

Turn off completely

Mute the sound

Watch the video input (VCR, camcorder, etc.)

Jump back to the previous program number

Display the on-screen information*

Adjust the volume of all program numbers automatically

Adjust the picture position when it is not aligned to the TV screen

Additional tasks

* The picture, sound, and either the program number or video input are

displayed. The on-screen display for the picture and sound information disappears after about three seconds.

Changing the on-screen display language

(except KV-XA51M61/XA21M83(Vientam))

Press SELECT until “LANGUAGE /

: ENGLISH”appears on the screen.

Press + or – to select “

“.

Tip

• You can also use SELECT and 2 +/– on the TV to select the on-screen

display language.

Press

1. The 1 indicator on the TV lights up red.

! on the TV.

t to select “VIDEO 1” or “VIDEO 2”. To return to the TV program, press a.

JUMP.

SELECT repeatedly until “INTELLIGENT VOL

”

appears, then press + or – to select “ON”. To cancel, select “OFF”.

SELECT repeatedly until

“PIC ROT

ATION” appears, then press + or – to adjust the alignment of the picture position.

The

icon on the screen flashes while adjusting.

LANGUAGE / : ENGLISH

SELECT

LANGUAGE / :

continued

PIC ROTATION

– 13 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

KV-XA21N93

RM-952

RM-915

Using Your New TV

Setting the Wake Up timer

Press

until the desired

period of time appears.

The Wake Up timer starts immediately after you have set it.

Select the program number or video input you want to display when you wake up.

Press ?/1 or set the Sleep timer if you want the TV to turn off automatically.

The

indicator on the TV lights up orange.

To cancel the Wake Up timer

Press

until “WAKE UP TIMER: OFF” appears or turn off the TV’s

main power.

Note

• If no buttons or controls are pressed for more than two hours after the TV is turned on using the Wake Up timer, the TV automatically goes into the standby mode. To continue watching the TV, press any button or control on the TV or the remote.

Setting the Sleep timer

Press

until the desired

period of time appears.

The Sleep timer starts immediately after you have set it.

To cancel the Sleep timer

Press

until “SLEEP TIMER: OFF” appears or turn the TV off.

WAKE UP TIMER:10M

WAKE UP TIMER:OFF

WAKE UP TIMER:12H00M

After 10 minutes

No Wake Up timer After 12 hours

SLEEP TIMER:30M

SLEEP TIMER:60M

SLEEP TIMER:OFF

SLEEP TIMER:90M

After 30 minutes

No Sleep Timer

After 60 minutes

After 90 minutes

Watching the TV (continued)

Advanced Operations

Customizing the picture and sound

You can customize the picture and sound by selecting the picture and sound modes or by adjusting its settings.

You can change the sound effect by selecting the surround mode.

Selecting the picture and sound modes

To select the picture mode

Press PIC MODE repeatedly until you get the desired picture mode.

Select To

“DYNAMIC” receive high contrast pictures.

“STANDARD” receive normal contrast pictures.

“SOFT” receive mild pictures.

To select the sound mode

Press SOUND MODE repeatedly until you get the desired sound mode.

Select To

“DYNAMIC” listen to dynamic and clear sound that emphasizes the low and

high sound.

“DRAMA” listen to sound that emphasizes vocals and background music.

“SOFT” receive soft sound.

Advanced Operations

SOUND MODE

PIC MODE

SELECT + or –

JUMP

SOUND

MODE

FAVORITE

PROGR

STANDARDDYNAMIC

SOFT

PIC MODE

≥

DYNAMIC

≥

DRAMA

≥

SOFT

SOUND

MODE

Advanced Operations

continued

KV-XA21M83/XA21M93/XA51M61/XA21P80

– 14 –

KV-XA21N93

RM-952

RM-915

Advanced Operations

SELECT

PICTURE 60

PICTURE COLOR

BRIGHT

HUE*

BALANCE TREBLE

BASS

SHARP

SURROUND: ON

SELECT

OFF

Customizing the picture and sound (continued)

Press SELECT repeatedly until “SURROUND” appears.

Press + or – to select “ON”.

To turn off the surround mode, select “OFF” .

Adjusting the picture and sound settings

Press SELECT until the desired setting appears.

Each time you press SELECT, the setting item will change as follows:

Press + or – to adjust the item.

To adjust other items, repeat steps 1 to 2.

* “HUE” can be adjusted for the NTSC system only.

Notes

• When you select a picture or sound mode, the adjusted settings will be reset according to the selected mode.

• You can also use SELECT and

+/– on the TV to adjust the picture and

sound settings.

Selecting the surround mode

Advanced Operations

Viewing your favorite channels

(except KV-XA21P80)

You can display six of your favorite channels for quick and easy selection. You can program the favorite channel setting as well.

Selecting a favorite channel

Press FAVORITE.

Press the number button from 1 to 6 to select the desired favorite channel.

When you use the

“F

AVORITE CH”

feature for the first time, six preset favorite channels will appear.

FAVORITE

+ or –

PROGR +/–

Number buttons

Programming the favorite channel

Press PROGR +/

– or number buttons to select the program number you want to program (e.g., program number 8).

Press SELECT until

“FAVORITE CH SETUP

”

appears.

Press + or – to select the favorite channel you want to program (e.g., 3).

Press SELECT.

The selected favorite channel (e.g., 3) turns red for about one second.

To program other favorite channels, repeat steps 1 to 4.

JUMP

SOUND

MODE

FAVORITE

PROGR

FAVORITE

FAVORITE CH

1PR01 2 PR02 3PR03 4PR04 5 PR05 6PR06

-/--

PROGR

SELECT

FAVORITE CH SETUP :

SELECT

– 15 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

KV-XA21N93

RM-952

RM-915

Advanced Operations

Blocking the channels (CHILD LOCK)

You can lock some program numbers to prevent children from watching certain channels, by using the buttons on the remote control.

Select the program number you want to lock.

Press SELECT until

“CHILD LOCK” appears on the screen.

Press + or – to select “ON”.

The

symbol appears on

the screen.

To cancel, press + or – to select “OFF”. The symbol disappears from the screen.

Note

• If you preset a locked program number, that particular program number will be unlocked automatically (see page 10).

SELECT

+ or –

JUMP

SOUND

MODE

FAVORITE

PROGR

CHILD LOCK: OFF

SELECT

CHILD LOCK: ON

Advanced Operations

Enjoying stereo or bilingual programs

(KV-XA21M93/XA51M61 only)

You can enjoy stereo sound or bilingual programs of NICAM and A2 stereo systems.

Press A/B repeatedly until you receive the sound you want.

The on-screen display changes to show the selected sound.

The

indicator on the TV lights up red when receiving any stereo or bilingual program.

When receiving a NICAM program

Broadcasting On-screen display (Selected sound)

NICAM stereo

NICAM bilingual

NICAM monaural

NICAM

MONO

(Stereo sound)

(Regular sound)

NICAM

MAIN

MONO

(Main sound)

(Regular sound)

NICAM

SUB

(Sub sound)

NICAM

MAIN

MONO

(Main sound)

(Regular sound)

A/B

L(MONO) R

PROGR

SELECT

AUTO PROGR

indicator

JUMP

SOUND

MODE

FAVORITE

PROGR

continued

– 16 –

KV-XA21N93

RM-952

RM-915

KV-XA21M83/XA21M93/XA51M61/XA21P80

Advanced Operations

When receiving an A2 program

Notes

• If the signal is very weak, the sound becomes monaural automatically.

• If the stereo sound is noisy when receiving a NICAM program, select “MONO”. The sound becomes monaural, but the noise is reduced.

If the sound is distorted when receiving a monaural program through the 8 (antenna) terminal

Press A/B repeatedly until “MONO” appears on the scr

een.

To cancel the monaural sound setting, press A/B again until “AUTO” appears on the screen.

Notes

• The “MONO” or “AUT

O” setting is memorized for each program

number.

• You cannot receive stereo broadcast signal when the TV is in the

“MONO”

setting. Normally set the TV to

“AUT

O”.

Broadcasting On-screen display (Selected sound)

A2 stereo

A2 bilingual

STEREO

MONO

(Stereo sound)

(Regular sound)

MONO

AUTO

MAIN

SUB

(Main sound)

(Sub sound)

Enjoying stereo or bilingual programs (continued)

Advanced Operations

Viewing Teletext

(KV-XA51M61 only)

TV stations broadcast an information service called Teletext via some TV channels. Teletext allows you to receive various information, such as shares market or news.

Displaying Teletext

Select a TV channel that carries the Teletext broadcast you want to watch.

Press

to display the

text.

A Teletext page (normally the index page) is displayed. If there is no Teletext broadcast, “100” is displayed at the top left corner of the screen.

To turn off Teletext

Press a.

A/B

FASTEXT

P166 SECTEXT 166 FR1 MAR 03:59:09

Fom Singapore

To PARIS

To OSAKA

To ROM A

To SYDNEY

Day Dep/Arr Flight Alrcraft

1.6 220/0588 SQ28 747 2 2130/1225 PA115 L15 3 2115/1330 SQ26 747

2.7 2130/0745 SQ24

747

4 2300/0915 AZ487 747

2.5 1000/1715 SQ6 747

4.6 0930/2015 CX522 L10

1 2210/0610 SQ21A 747 2 2100/0835 SQ21A 747

JUMP

SOUND

MODE

FAVORITE

PROGR

– 17 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

KV-XA21N93

RM-915

RM-952

Advanced Operations

Additional Teletext tasks

display a Teletext page on the TV picture

check the contents of a Teletext service

select a Teletext page

Hold (pause) a Teletext display

reveal concealed information (e.g., an answer to a quiz)

enlarge the Teletext display

wait for a Teletext page while watching a TV program

* You can also select a Teletext page that appears in the colored column at

the bottom of the screen using the corresponding color-coded button on the remote.

Using FASTEXT

This feature allows you to quickly access a Teletext page that uses FASTEXT. When a FASTEXT program is broadcasted, the colored menus appear at the bottom of the screen. The colors of the menus correspond to the red x , green x , yellow x , and blue x colorcoded buttons on the remote.

To access a FASTEXT menu

Press the color-coded button on the remote corresponding to the menu you want. The menu page appears on the screen after several seconds.

Do this

Press

Each time you press

, the screen changes as

follows: Teletext t Teletext and TV t TV.

Press

. An overview of the Teletext contents and page numbers appear on the screen.

Press the number buttons to enter the three-digit page number of the desired Teletext page. * If you make a mistake, reenter the correct page number. To access the next or previous page, press PROGR +/–.

Press

to display the symbol

“

z ” at the top left

corner of the screen. To resume normal Teletext operation, press

Press

. To conceal the information, press the button again.

Press

. Each time you press

, the Teletext display changes as follows: Enlarge upper half t Enlarge lower half t Normal size.

1 Enter the Teletext page number that you want to

refer to, then press

2 When the page number is displayed, press

show the text.

Additional Information

Self-diagnosis function

Your TV is equipped with a self-diagnosis function. If there is a problem with your TV, the 1 indicator flashes red. The number of times the 1 indicator flashes indicates the possible causes.

Check that the 1 indicator flashes red a number of times between 3-second intervals.

Count the number of times the 1 indicator flashes.

Press ! (main power) to turn off your TV.

Inform your nearest Sony service center about the number of times the 1 indicator flashes. Be sure to note the model name and serial number located on the rear of your TV.

Front of TV

1 indicator

L(MONO) R

PROGR

SELECT

AUTO PROGR

– 18 –

KV-XA21N93

RM-952

RM-915

KV-XA21M83/XA21M93/XA51M61/XA21P80

Additional Information

Snowy picture

Noisy sound

Distorted picture

Noisy sound

Good picture

Noisy sound

No picture

No sound

Troubleshooting

(KV-XA21M83 Vietnam)

If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer.

Possible causeSymptom Solutions

• Connection is loose or the cable is damaged.

• Channel presetting is inappropriate or incomplete.

• The antenna type is inappropriate.

• The antenna direction is inappropriate.

• Signal transmission is low.

• Broadcast signals are too strong.

• The TV system setting is inappropriate.

• The power cord, antenna or VCR is not connected.

• The TV is not turned on.

–

• Check the antenna cable and connection on the TV, VCR and on the wall.

• Press SELECT until

“MANUAL

PROGRAM” appears on the screen, then preset the channel again.

• Check the antenna type (VHF/UHF). Contact a Sony dealer for advice.

• Adjust the antenna direction. Contact a Sony dealer for advice.

• Try using a booster.

• Turn off or disconnect the booster if it is in

use.

• If the sound of some channels are noisy, select the channel, then select the appropriate TV system (TV SYS).

• Check the power cord, antenna and the VCR connections.

• Press ?/1 (power).

• Press ! (main power) on the TV to turn

off the TV for about five seconds, then turn it on again.

Page

Additional Information

Good picture

No sound

Dotted lines or stripes

Double images or “ghosts”

No color

Abnormal color patches

• Press 2 + to increase the volume level.

• Press % to cancel the muting.

• Do not use a hair dryer or other

equipment near the TV.

• Adjust the antenna direction for minimum interference. Contact a Sony dealer for advice.

• Use a highly directional antenna.

• Use the fine tuning (FINE) function.

• Adjust the antenna direction. Contact a

Sony dealer for advice.

• Turn off or disconnect the booster if it is in use.

• Press SELECT until

“COLOR” appears

on the screen, then press + or – to adjust the color level.

• Press SELECT until

“COLOR SYS ”

appears on the screen, then check the color system setting (usually set this to

“AUTO”).

• Adjust the antenna direction. Contact a

Sony dealer for advice.

• Keep external speakers or other electrical equipment away from the TV. Do not move the TV while the TV is turned on. Press ! (main power) on the TV to turn off the TV for about five minutes, then turn it on again.

Possible cause

Symptom

Solutions

• The volume level is too low.

• The sound is muted.

• There is local

interference from cars, neon signs, hair dryers, power generators, etc.

• Broadcast signals are reflected by nearby mountains or buildings.

• The antenna direction is inappropriate.

• Use of a booster is inappropriate.

• The color level setting is too low.

• The color system setting is inappropriate.

• The antenna direction is inappropriate.

• The magnetic disturbance from external speakers or other equipment, or the direction of the earth’s magnetic field may affect the TV.

–

Page

continued

– 19 –

KV-XA21N93

RM-952

RM-915

KV-XA21M83/XA21M93/XA51M61/XA21P80

Additional Information

–

Picture slant

Lines moving across the TV screen.

The 1 indicator on your TV flashes red a number of times between 3-second intervals.

TV cabinet creaks.

A “boom” sound is heard when the TV is turned on.

Possible causeSymptom Solutions

• The magnetic disturbance from external speakers or other equipment, or the direction of the earth’s magnetic field may affect the TV.

• There is interference from external sources, e.g., heavy machineries, nearby broadcast station.

• Your TV may need service.

• Changes in room temperature sometimes make the TV ca

binet expand or contract, making a noise. This does not indicate a malfunction.

•

The TV’s demagnetizing function is working. This does not indicate a malfunction.

Page

•Keep external speakers or other electrical equipment away from the TV.

•Press SELECT until

“PIC ROT

ATION” appears on the screen, then press + or – to adjust the picture until it is optimal.

•Use the fine tuning (FINE) function.

•Contact your nearest Sony service center.

—

Troubleshooting (continued)

Good morning!

Additional Information

Snowy picture

Noisy sound

Distorted picture

Noisy sound

Good picture

Noisy sound

No picture

No sound

Troubleshooting

(KV-XA51M61/XA21M93/XA21M83(India))

If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer.

Possible causeSymptom Solutions

• Connection is loose or the cable is damaged.

• Channel presetting is inappropriate or incomplete.

• The antenna type is inappropriate.

• The antenna direction is inappropriate.

• Signal transmission is low.

• Broadcast signals are too strong.

• The TV system setting or channel presetting is inappropriate or incomplete.

• The selected sound is inappropriate.

• The power cord, antenna or VCR is not connected.

• The TV is not turned on.

–

• Check the antenna cable and connection on the TV, VCR and on the wall.

• Press SELECT until

“MANUAL

PROGRAM” appears on the screen, then preset the channel again.

• Check the antenna type (VHF/UHF). Contact a Sony dealer for advice.

• Adjust the antenna direction. Contact a Sony dealer for advice.

• Try using a booster.

• Turn off or disconnect the booster if it is in

use.

• If the sound of all the channels are noisy, check the TV system (TV SYS) setting, then press AUTO PROGR to preset the channels again.

• If the sound of some channels are noisy, select the channel, then select the appropriate TV system (TV SYS).

• If the sound of some channel are noisy, select the channel, then press A/B to select the main sound (KV-XA21M93 only).

• Check the power cord, antenna and the VCR connections.

• Press ?/1 (power).

• Press ! (main power) on the TV to turn

off the TV for about five seconds, then turn it on again.

Page

– 20 –

KV-XA21N93

RM-952

RM-915

Additional Information

Good picture

No sound

Dotted lines or stripes

Double images or “ghosts”

No color

Abnormal color patches

TV cannot receive stereo broadcast signal

• Press 2 + to increase the volume level.

• Press % to cancel the muting.

• Press A/B until a better sound is heard

• Do not use a hair dryer or other

equipment near the TV.

• Adjust the antenna direction for minimum interference. Contact a Sony dealer for advice.

• Use a highly directional antenna.

• Use the fine tuning (FINE) function.

• Adjust the antenna direction. Contact a

Sony dealer for advice.

• Turn off or disconnect the booster if it is in use.

• Press SELECT until

“COLOR” appears

on the screen, then press + or – to adjust the color level.

• Press SELECT until

“COLOR SYS ”

appears on the screen, then check the color system setting (usually set this to

“AUTO”).

• Adjust the antenna direction. Contact a

Sony dealer for advice.

• Press A/B until “AUTO” appears on the screen.

Possible cause

Symptom

Solutions

• The volume level is too low.

• The sound is muted.

• Broadcast signal has a

transmission problem.

• There is local interference from cars, neon signs, hair dryers, power generators, etc.

• Broadcast signals are reflected by nearby mountains or buildings.

• The antenna direction is inappropriate.

• Use of a booster is inappropriate.

• The color level setting is too low.

• The color system setting is inappropriate.

• The antenna direction is inappropriate.

• The magnetic disturbance from external speakers or other equipment, or the direction of the earth’s magnetic field may affect the TV.

• The stereo reception setting is inappropriate.

–

Page

continued

Additional Information

–

Possible causeSymptom Solutions

• Connection is loose or the cable is damaged.

• The antenna direction is inappropriate.

• Broadcast signal has a transmission problem.

• The magnetic disturbance from external speakers or other equipment, or the direction of the earth’s magnetic field may affect the TV.

• There is interference from external sources, e.g., heavy machineries, nearby broadcast station.

• Your TV may need service.

• Changes in room temperature sometimes make the TV ca

binet expand or contract, making a noise. This does not indicate a malfunction.

•

The TV’s demagnetizing function is working. This does not indicate a malfunction.

Page

• Check the antenna cable and connection on the TV, VCR and on the wall.

• Adjust the antenna direction. Contact a Sony dealer for advice.

• Press A/B until a better sound is heard.

• Keep external speakers or other electrical

equipment away from the TV.

•Press SELECT until

“PIC ROT

ATION” appears on the screen, then press + or – to adjust the picture until it is optimal.

•Use the fine tuning (FINE) function.

•Contact your nearest Sony service center.

—

Troubleshooting (continued)

Stereo broadcast sound switches on and off or is distorted.

The sound switches between monaural and stereo frequently.

Picture slant

Lines moving across the TV screen.

The 1 indicator on your TV flashes red a number of times between 3-second intervals.

TV cabinet creaks.

A “boom” sound is heard when the TV is turned on.

Good morning!

– 21 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

KV-XA21N93

RM-952

RM-915

KV-XA21M83/XA21M93/XA51M61/XA21P80

Additional Information

• Check the antenna cable and connection on the TV, VCR and on the wall.

• Press SELECT until

“MANUAL

PROGRAM” appears on the screen, then preset the channel again.

• Check the antenna type (VHF/UHF). Contact a Sony dealer for advice.

• Adjust the antenna direction. Contact a Sony dealer for advice.

• Try using a booster.

• Turn off or disconnect the booster if it is

in use.

• Check the power cord, antenna and the VCR connections.

• Press ?/1 (power).

• Press ! (main power) on the TV to turn

off the TV for about five seconds, then turn it on again.

Snowy picture

Noisy sound

Distorted picture

Noisy sound

No picture

No sound

Troubleshooting

(KV-XA21P80 only)

If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer .

Possible causeSymptom

Solutions

• Connection is loose or the cable is damaged.

• Channel presetting is inappropriate or incomplete.

• The antenna type is inappropriate.

• The antenna direction is inappropriate.

• Signal transmission is low.

• Broadcast signals are too strong.

• The power cord, antenna or VCR is not connected.

• The TV is not turned on.

Page

–

Additional Information

continued

Additional Information

Troubleshooting (continued)

Good picture

No sound

Dotted lines or stripes

Double images or “ghosts”

No color

Abnormal color patches

• Press 2 + to increase the volume level.

• Press % to cancel the muting.

• Do not use a hair dryer or other

equipment near the TV.

• Adjust the antenna direction for minimum interference. Contact a Sony dealer for advice.

• Use a highly directional antenna.

• Use the fine tuning (FINE) function.

• Adjust the antenna direction. Contact a

Sony dealer for advice.

• Turn off or disconnect the booster if it is in use.

• Press SELECT until

“COLOR” appears

on the screen, then press + or – to adjust the color level.

• Press SELECT until

“COLOR SYS ”

appears on the screen, then check the color system setting (usually set this to

“AUTO”).

• Adjust the antenna direction. Contact a

Sony dealer for advice.

Possible cause

Symptom

Solutions

• The volume level is too low.

• The sound is muted.

• There is local

interference from cars, neon signs, hair dryers, power generators, etc.

• Broadcast signals are reflected by nearby mountains or buildings.

• The antenna direction is inappropriate.

• Use of a booster is inappropriate.

• The color level setting is too low.

• The color system setting is inappropriate.

• The antenna direction is inappropriate.

• The magnetic disturbance from external speakers or other equipment, or the direction of the earth’s magnetic field may affect the TV.

–

Page

– 22 –

KV-XA21N93

RM-952

RM-915

Additional Information

–

Picture slant

Lines moving across the TV screen.

The

indicator on your TV flashes red a number of times between 3-second intervals.

TV cabinet creaks.

A “boom” sound is heard when the TV is turned on.

Possible causeSymptom Solutions

Good morning!

• The magnetic disturbance from external speakers or other equipment, or the direction of the earth’s magnetic field may affect the TV.

• There is interference from external sources, e.g., heavy machineries, nearby broadcast station.

• Your TV may need service.

•

Changes in room temperature sometimes make the TV cabinet expand or contract, making a noise. This does not indicate a malfunction.

• The TV’s demagnetizing function is working. This does not indicate a malfunction.

Page

•Keep external speakers or other electrical equipment away from the TV.

•Press SELECT until

“PIC ROT

ATION” appears on the screen, then press + or – to adjust the picture until it is optimal.

•Use the fine tuning (FINE) function.

•

Contact your nearest Sony service center.

—

Additional Information

Overview of controls

TV front panel

L(MONO) R

PROGR

SELECT

AUTO

PROGR

L(MONO) R

PROGR

SELECT

AUTO PROGR

PageFunctionButton

Preset channels automatically.5 Select the desired item. 11 Select program number. 12 Turn off completely or turn on 12

the TV. Adjust volume. 12 Standby indicator.12 Select TV or video input. 13 Wake Up indicator.14 Stereo/bilingual indicator.19

Headphone jack. –

AUTO PROGR SELECT PROGR +/–

2 +/–

(KV-XA21M93/XA51M61 only)

continued

– 23 –

KV-XA21M83/XA21M93/XA51M61/XA21P80

KV-XA21N93

RM-952

RM-915

KV-XA21M83/XA21M93/XA51M61/XA21P80

Additional Information

Remote Control

The names/symbols of buttons on the remote are indicated in different colors to represent the available functions.

Label color

White

Green

Button function

For general TV operations

For Teletext operations

PageButton Function

JUMP

SOUND

MODE

FAVORITE

PROGR

Select the desired item. Adjust value. Select program number. Input numbers. Adjust volume. Turn off temporarily or turn on

the TV. Select TV or video input. Display the TV program. Mute the sound. Display on-screen information. Jump to previous program

number.

Set TV to turn on automatically. Set TV to turn off automatically. Select picture mode. Select sound mode. Display favorite channels.

Select stereo/bilingual mode.

Display Teletext broadcast. Display Teletext service

contents. Stop Teletext display from

scrolling. Reveal concealed information. Enlarge the Teletext display. Show TV screen while waiting

for Teletext page. Access a FASTEXT menu.

10 10 12 12 12 12

13 13 13 13 13

14 14 15 15 17

–

– –

–

– – –

–

SELECT +/– PROGR +/– 0 – 9, 2 +/–

t a

JUMP

Timer operations

PIC MODE SOUND MODE FAVORITE Stereo/bilingual operations

(Not used for these models) A/B Teletext operations

(Not used for these models)

x (red, green,

yellow, blue)

Overview of controls (continued)

– 24 –

KV-XA21N93

RM-952

RM-915

The operating instruction mentioned here are partial abstracts

WARNING

• Dangerously high voltages are present inside the TV.

• Operate the TV only between 110-240 V AC.