Sony KV-PG21M70, KV-PG21P40L, KV-PG21P40N, KV-PG21P40, KV-PG21P70 Service Manual

REVISION HISTORY

BG-2T

CHASSIS

MODEL

KV-PG21M70 KV-PG21P40/L

(Pearl Blue)

KV-PG21P40/N

(Champange Gold)

KV-PG21P40 KV-PG21P70

NO DATE DESCRIPTION OF REVISION

PA RT NO. : 9-872-260-01

SERVICE MANUAL

BG-2T

CHASSIS

MODEL COMMANDER DEST. CHASSIS NO.

KV-PG21M70 RM-952 E SCC-U68A-A KV-PG21P40/L RM-952 Malaysia SCC-U71A-A

(Pearl Blue) (Blue)

KV-PG21P40/NRM-952 Malaysia SCC-U71B-A

(Champange Gold) (Silver)

KV-PG21P40 RM-952 Singapore SCC-U66A-A KV-PG21P70 RM-952 E SCC-U68B-A

MODEL COMMANDER DEST. CHASSIS NO.

JUMP

SOUND

PROGRÁ

MODE

FAVORITE

TRINITRON

COLOR TV

KV-PG21P40/PG21M70/PG21P70

RM-952

Power requirements 110-240 V AC, 50/60 Hz

220-240 V AC, 50/60 Hz Malaysia only

Power consumption (W) Indicated on the rear of the TV

Television system B/G KV-PG21P70/PG21P40 only

B/G, I, D/K, M KV-PG21M70 only

Color system PAL, PAL 60, NTSC3.58 (AV IN), NTSC4.43 KV-PG21P70/PG21P40 only

PAL, PAL 60, SECAM, NTSC 3.58, NTSC 4.43 KV-PG21M70 only

Channel coverage

B/G VHF: E2 to E12

UHF: E21 to E69 CATV: S01 to S03, S1 to S41

I UHF: B21 to B68 KV-PG21M70

CATV: S01 to S03, S1 to S41

D/K VHF: C1 to C12, R1 to R12 KV-PG21M70

UHF: C13 to C57, R21 to R60 CATV: S01 to S03, S1 to S41, Z1 to Z39

M VHF: A2 to A13 KV-PG21M70

UHF: A14 to A79

CATV: A-8 to A-2, A to W+4, W+6 to W+84

˘ (Antenna) 75-ohm external terminal

Audio output (Speaker) 3W

Number of terminal

D Video Input: 2* Output: 1 Phono jacks; 1 VP-P, 75 ohms * One input lines available

≥ Audio Input: 2* Output: 1 Phono jacks; 500 mVrms * One input lines available

(Earphone) Output: 1 Monaural minijack

Picture tube 21 in.

Tube size (cm) 54 Measured diagonally

Screen size (cm) 51 Measured diagonally

Dimension (w/h/d, mm) 497 x 458 x 487

Mass (kg) 25

SPECIFICATIONS

Note

CAUTION

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.

Design and specifications are subject to change without notice.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

– 2 –

KV-PG21P40/PG21M70/PG21P70

RM-952

Section Title Page

SELF DIAGNOSTIC FUNCTION ................................... 4

1. GENERAL ................................................................. 7

2. DISASSEMBLY

2-1. Rear Cover Removal ............................................... 14

2-2. Speaker Removal .................................................... 14

2-3. Chassis Assy Removal ............................................ 14

2-4. Service Position ...................................................... 14

2-5. Terminal Bracket Removal ..................................... 14

2-6. Replacement Of Parts ............................................. 15

2-6-1. Replacement Of Light Guide ....................... 15

2-6-2. Replacement Of Power Button .................... 15

2-7. Picture Tube Removal ............................................. 15

3. SET-UP ADJUSTMENTS

3-1. Beam Landing ......................................................... 16

3-2. Convergence ............................................................ 17

3-3. Focus Adjustment .................................................... 19

3-4. G2 (SCREEN) and white balance adjustments ...... 19

4. CIRCUIT ADJUSTMENTS

4-1. Adjustment With Commander ................................ 20

4-2. Adjustment Method ................................................ 20

4-3. Picture Quality Adjustment .................................... 25

4-4. Deflection Adjustment ............................................ 25

4-5. A Board Ajustment After IC003 (MEMORY)

Replacement ............................................................ 25

4-6. Picture Distortion Adjustment ................................ 26

Section Title Page

5. DIAGRAMS

5-1. Block Diagram ........................................................ 27

5-2. Circuit Boards Location .......................................... 29

5-3. Schematic Diagram ................................................. 30

(1) Schematic Diagram of A Board ........................ 31

(2) Schematic Diagram of CV Board ..................... 35

5-4. Voltage Measurement ............................................. 37

5-5. Waveforms .............................................................. 40

5-6. Printed Wiring Boards and Parts Location ............. 41

5-7. Semiconductors ....................................................... 44

6. EXPLODED VIEWS

6-1. Picture tube and Chassis ......................................... 46

7. ELECTRICAL PARTS LIST.................................... 47

– 3 –

KV-PG21P40/PG21M70/PG21P70

RM-952

SELF DIAGNOSTIC FUNCTION

The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/ TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.

1. DIAGNOSTIC TEST INDICATORS

When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the problem. If there is more than one error, the lamp will identify the first of the problem areas.

Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.

Diagnostic

Item

Description

• Power does not turn on

• +B overcurrent (OCP)

• Horizontal deflection overdrive

• White balance failure (no PICTURE)

• Vertical deflection stopped

• Micro reset

No. of times

STANDBY/TIMER

lamp flashes

Does not light

2 times

4 times

—

Self-diagnostic

display/Diagnostic

result

—

002:000 or

002:001~255

004:000 or

004:001~225

101:00 or

101:001~225

Probable

Cause

Location

• Power cord is not plugged in.

• Fuse is burned out F4601 (F)

• H.OUT Q801 is shorted. (A board)

• -13V is not supplied. (A board)

• IC 551 faulty (A board)

• Discharge CRT (CV Board)

• Static discharge

• External noise

Detected

Symptoms

• Power does not come on.

• No power is supplied to the TV.

• AC power supply is faulty.

• Power does not come on.

• Load on power line is shorted.

• Has entered standby state after horizontal raster.

• Power line is shorted or power supply is stopped.

• Vertical deflection pulse is stopped

• Power is shut down shortly, after this return back to normal.

• Detect Micro latch up.

Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.

The symptom that is diagnosed first by the microcontroller is displayed on the screen.

Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.

– 4 –

2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT

2 times

KV-PG21P40/PG21M70/PG21P70

RM-952

Diagnostic Item Flash Count*

+B overcurrent/overvoltage 2 times

4 times

Lamp ON 0.3 sec.

Lamp OFF 0.3 sec.

Lamp OFF 3 sec.

Vertical deflection stopped 4 times

* One flash count is not used for self-diagnostic.

STANDBY/SLEEP lamp

3. STOPPING THE STANDBY/TIMER FLASH

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp from flashing.

4. SELF-DIAGNOSTIC SCREEN DISPLAY

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen:

[To Bring Up Screen Test]

In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:

[Screendisplay] / channel [5] / Sound volume [-] / Power ON

Note that this differs from entering the service mode (mode volume [+]).

Self-Diagnosis screen display

SELF DIAGNOSTIC

002 : 000 004 : 000

101 : 000

Numeral "0" means that no fault has been detected.

– 5 –

KV-PG21P40/PG21M70/PG21P70

RM-952

5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”.

Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.

[Clearing the result display]

To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic screen is being displayed.

Channel [8] / 0

[Quitting Self-diagnostic screen]

To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.

6. SELF-DIAGNOSTIC CIRCUIT

FROM [+B] Q500

IC301

Y/CHROMA JUNGLE

MP/

PROTECT

SDA

[V] D553

IC001

SYSTEM

IO-8DAT B-DAT

O-LED

IO-SDAT

IC003

MEMORY

[+BovercurrentªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q500. If Q500 go to

ON and the voltage to pin 50 of IC301 more than 3.5V when V.SYNC is more than seven verticals in a period, the unit will automatically turn off.

[Verticaldeflectionstopped] Occurs when an absence of the vertical deflection pulse is detected by Pin 17 and

IC001 shut down the power supply.

[Whitebalancefailure] If the RGB levels* do not balance or become low level within 5 seconds, this error

will be detected by IC301. TV will stay on, but there will be no picture.

* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)

– 6 –

KV-PG21P40/PG21M70/PG21P70

PROGR

SELECT

(MONO)

L(MONO)R

★

RM-952

A Getting Started

Step 1

SELECT

PROGR

SELECT

Insert the batteries (supplied) into the remote.

Note

• Do not use old batteries nor use different types of batteries together.

Step 2

Connect the antenna cable (not supplied) to 8 at the rear of the TV.

Tip

• You can also connect your TV to other optional components. (See E)

Step 3

Plug in the power cord, then press ! on the TV to turn it on.

Step 4

Press SELECT and PROGR + on the TV at the same time for one to two seconds to preset the channels automatically. (See J)

Tip

• To stop the automatic channel presetting, press SELECT twice.

Step 5

Press SELECT on the remote until “LANGUAGE/ : ENGLISH” appears on the screen, then press + or – to change the on-screen display language.

WARNING (continued)

Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days.

Do not install the TV in an unstable position. Use a proper TV stand.

Securing the TV

Do not plug in too many appliances to the same power socket. Do not damage the power cord.

Do not place any objects on the TV.

B KV-PG21/TG21 only

To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV

20 mm

screws clamps band

3.8 mm

Screw the band to the TV stand and to the provided hole at the rear of your TV.

(1) Put a cord or chain through the

clamps.

(2) Screw one clamp to a wall or pillar

and the other clamp to the provided hole at the rear of your TV.

WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 110 – 240 V AC. (Malaysia: 220 – 240 V AC)

• Do not plug in the power cord until you have completed making all other connections;

GENERAL

SECTION 1

otherwise a minimum leakage current might flow through the antenna and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid that leaks from the batteries touches you, immediately wash it away with water.

For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms.

To prevent fire or shock hazard, do not expose the TV to rain or moisture.

Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet.

Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel.

Note

• Use only the supplied screws. Use of other screws may damage the TV.

TV front and rear panels

TV rear panel

For children’s safety, do not leave children alone with the TV. Do not allow children to climb onto it.

Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only.

Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not scratch the picture tube.

Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations.

TV front panel

Button Function

! Turn off completely or turn on the TV.

2 3

1 Standby indicator.

3 3 4

PROGR +/– Select program number.

2 +/– * Adjust volume.

t Select TV or video input.

SELECT Select the desired item.

i Headphone terminal. (KV-TG21 only)

8 9,qa

t Video input terminal.

8 Antenna terminal.

T Monitor output terminal.

* You can also use the 2 +/– buttons on the TV to work as the +/– buttons on the remote.

★

The R (audio input) jacks are only available for KV-TG21 only.

Remote control sensor.

Stereo/bilingual indicator. (KV-TG21 only)

Wake Up indicator.

Earphone terminal. (KV-PG21/PG14 only)

the Operating Instruction Manual remain as in the manual.

The operating instruction mentioned here are partial abstracts

from the Operating Instruction Manual. The page numbers of

– 7 –

KV-PG21P40/PG21M70/PG21P70

RM-952

Connecting optional components

Connecting to the video input terminal ( t )

TV front panel

TV rear panel

(MONO)

L(MONO)R

★

Audio/Video cable

(not supplied)

Antenna cable (not supplied)

Audio/Video cable

(not supplied)

Camcorder

Video game

equipment

★

Note

• Do not connect video equipment to the same time; otherwise the picture will not be displayed properly on the screen.

Connecting to the monitor output terminal (T)

TV rear panel

L(MONO)R

(video input) at the front and the rear of your TV at

Audio/Video cable

(not supplied)

Audio system

★

The R (audio input) jacks are only available for KV-TG21 only.

VCR

H Remote control

0 qa qs

SOUND

MODE

JUMP

PROGR

qj qk

FAVORITE

1 ?/1 Turn off temporarily or

2 a Display the TV program.

3 JUMP Jump to previous

4 PROGR +/– Select program number. 5 2 +/– Adjust volume. 6 SELECT Select the desired item. 7 PIC MODE Select picture mode.

9 +/– Adjust items.

qa % Mute the sound.

qd t Select TV or video input. qf 0 – 9, ÷ Input numbers.

Timer operations

qj Set TV to turn on

qk Set TV to turn off

Sound mode operations (KV-TG21M61 only)

qg SOUND MODE Select sound mode.

Stereo/bilingual operations (KV-TG21M61 only)

qh A/B Select stereo/bilingual

Teletext operations (KV-TG21M61 only)

8 x (red, green, Access a FASTEXT

yellow, blue) menu.

0 Reveal concealed

qs Display Teletext

ql FAVORITE

Button Function

turn on the TV.

program number.

Display on-screen information.

automatically.

mode.

information

broadcast.

Stop Teletext display from scrolling.

Enlarge the Teletext display.

Display Teletext service contents.

Show TV screen while waiting for Teletext page

Not function for your TV.

See

–

F Troubleshooting

If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer.

Symptom Solutions

Snowy picture,

noisy sound

Good picture,

noisy sound

No picture,no sound

Good picture, no sound

Dotted lines or stripes

Double images or

“ghosts”

No color

Abnormal color

patches

Teletext display is

incomplete (snowy

picture or double

images).

(KV-TG21M61 only)

The 1 (standby)

indicator on your TV

flashes red several

times after every

three seconds.

TV cabinet creaks.

A "boom" sound is

heard when the TV is

turned on.

• Check the antenna cable and connection on the TV, VCR and on the wall.

• Preset the channel manually again. (See J)

• Check the antenna setup. Contact a Sony dealer for advice.

• Select the appropriate TV system. (KV-PG21M70/PG14M40/TG21M61

only) (See J)

• Press A/B until the sound is optimal. (KV-TG21M61 only)

• Check the power cord, antenna and the VCR connections.

• Press ?/1 (power) or ! (main power) to turn on the TV.

• Press 2 + to increase the volume level.

• Press % to cancel the muting.

• Do not use a hair dryer or other equipment near the TV.

• Check the antenna setup. Contact a Sony dealer for advice.

• Use the fine tuning ("FINE") function. (See J)

• Turn off or disconnect the booster if it is in use.

• Check the antenna setup. Contact a Sony dealer for advice.

• Select the appropriate color system. (See J)

• Adjust the color level. (See K)

• Check the antenna setup. Contact a Sony dealer for advice.

•

Keep external speakers or other electrical equipment away from the TV. Press ! (main power) to turn off the TV for about 15 minutes, then turn it on again to demagnetize the TV.

• Check the antenna cable and connection on the TV, VCR and on the wall.

• Use the fine tuning (“FINE”) function. (See J)

• Check the antenna setup. Contact a Sony dealer for advice.

• Count the number of times the 1 (standby) indicator flashes. Press !

(main power) to turn off your TV. Contact your nearest Sony service center.

• Changes in room temperature sometimes make the TV cabinet expand or contract, making a noise. This does not indicate a malfunction.

• The TV's demagnetizing function is working. This does not indicate a malfunction.

I Setting the timers

You can turn on and off your TV by using the and buttons respectively.

Setting the Wake Up timer

\/1

JUMP

SOUND

PROGR

MODE

FAVORITE

Notes

• You can also cancel the Wake Up and Sleep timers by turning off the TV’s main power.

• If no buttons or controls are pressed for more than two hours after the TV is turned on using

the Wake Up timer, the TV automatically goes into standby mode.

Press until the desired period of time appears

on the screen.

WAKE UP TIMER:0H10M

(After 10 minutes)

WAKE UP TIMER:OFF (No Wake Up timer) (After 12 hours)

The Wake Up timer starts immediately after you have set it.

Select the program number or video input you

want to wake up to.

Press \/1, or set the Sleep timer if you want

the TV to turn off automatically.

indicator on the TV lights up orange when

The the TV goes into standby mode.

WAKE UP TIMER:12H00M

Setting the Sleep timer

Press until the desired period of time appears on the screen.

SLEEP TIMER:30M SLEEP TIMER:60M (After 30 minutes)

SLEEP TIMER:OFF SLEEP TIMER:90M (No Sleep timer)

The Sleep timer starts immediately after you have set it.

(After 60 minutes)

(After 90 minutes)

– 8 –

KV-PG21P40/PG21M70/PG21P70

PICTURE COLOR BRIGHT HUE

BALANCE TREBLE BASS

SHARP

d m

orn

ing!

Good morning!

RM-952

Presetting channels (continued)

To change the TV system setting (KV-PG21M70/PG14M40/TG21M61 only)

If the picture or sound is abnormal when receiving programs through the 8 (antenna) terminal

(1) Press SELECT until “TV SYS” appears on the screen.

(2) Press + or – to select the appropriate TV system until the picture or sound quality

is optimal.

B/G I D/K M

To change the color system setting

If the color is abnormal when receiving programs through the 8 (antenna) terminal or the t (video input) terminal

(1) Press SELECT until “COLOR SYS” appears on the screen.

(2) Press + or – to select the appropriate color system until the color is optimal.

AUTO PAL SECAM NTSC3.58 NTSC4.43

Note

• The color system “SECAM” is available for KV-PG21M70/PG14M40/TG21M61 only.

To skip program numbers

(1) Press PROGR +/– or the number buttons until the unused or unwanted program

number appears on the screen.

(2) Press SELECT until “MANUAL PROGRAM” appears on the screen.

(3) Press + or – once to enter the “MANUAL PROGRAM” mode.

(4) Press PIC MODE to skip the unused or unwanted program number.

(5) Press SELECT to exit the “MANUAL PROGRAM” mode.

Note

• To restore the skipped program number again, preset the channel automatically or manually.

To use the fine tuning function

The fine tuning (FINE) function may help to reduce the following problems: incomplete Teletext display (KV-TG21M61 only), double images and lines moving across the TV screen.

You can use the fine tuning function as below:

(1) Select the program number you want to adjust.

(2) Press SELECT until “MANUAL PROGRAM” appears on the screen.

(3) Press + or – once to enter the “MANUAL PROGRAM” mode.

to display “FINE” on the screen.

(4) Press

(5) Press + or – continuously until the above problems are minimized.

The + or – icon on the screen flashes while tuning.

(6) Press SELECT to exit the “MANUAL PROGRAM” mode.

Customizing the picture and sound

You can customize the picture and sound by selecting the picture and sound modes or by adjusting its settings.

Selecting the picture mode

Press PIC MODE to select the desired picture mode.

Select To

“DYNAMIC” view high contrast pictures.

“STANDARD” view normal contrast pictures.

JUMP

SOUND

MODE

SELECT

+ or –

PIC MODE

SOUND

MODE

FAVORITE

“SOFT” view mild pictures.

PROGR

Selecting the sound mode

B KV-TG21M61 only

Press SOUND MODE to select the desired sound mode.

Select To

“9 DYNAMIC” listen to dynamic and clear

“9 DRAMA” listen to sound that emphasizes

“9 SOFT” listen to soft sound.

sound that emphasizes the low and high sound.

vocals and background music.

Adjusting the picture and sound settings

Press SELECT until the desired setting appears.

Each time you press SELECT, the setting item will change as follows:

Press + or – to adjust the item.

To adjust other items, repeat steps 1 to 2.

Notes

•“BASS”, “TREBLE” and “BALANCE” can be adjusted for KV-TG21M61 only.

•“HUE” can be adjusted for the NTSC color system only.

• Reducing “SHARP” can also reduce picture noise.

Presetting channels

You can automatically preset up to 100 TV channels in numerical sequence from program number 1, or manually preset desired channels and channels that cannot be preset automatically.

Presetting channels automatically from a specified program number

Number buttons

SOUND

MODE

Press SELECT until “AUTO PROGRAM” appears

on the screen.

Press + or – once to enter the “AUTO

JUMP

PROGR

PROGRAM” mode.

The on-screen display will start flashing.

Press PROGR +/– or the number buttons until

+ or –

PIC MODE

SELECT

PROGR +/–

FAVORITE

the desired program number appears on the screen.

Press + or – to start presetting channels

automatically.

Presetting channels manually

Press SELECT until “MANUAL PROGRAM”

appears on the screen.

Press + or – once to enter the “MANUAL

PROGRAM” mode.

Press PROGR +/– or the number buttons until

the desired program number appears on the screen.

Press + or – until the desired channel picture

appears on the screen.

To preset other channels manually, repeat steps

3 to 4.

Adjusting the picture position

KV-PG21M70/PG21P70/PG21P40/TG21M61 only

If the picture is slanting, you can adjust the picture position using the “PIC ROTATION” function until it is optimal.

Slanting Optimal

Press SELECT repeatedly until “PIC ROTATION”

+ or –

FAVORITE

SELECT

Note

• To reduce the slanting picture, keep external speakers or other electrical equipment away from the TV.

appears on the screen.

Press + or – to adjust the picture position.

The + or icon on the screen flashes while adjusting.

– 9 –

KV-PG21P40/PG21M70/PG21P70

RM-952

Enjoying stereo or bilingual programs

KV-TG21M61 only

You can enjoy stereo sound or bilingual programs of NICAM and A2 stereo systems by using the A/B button.

When receiving a NICAM program

Broadcasting On-screen display (Selected sound)

NICAM

SOUND

MODE

A/B

FAVORITE

Notes

• If the stereo sound is noisy when receiving a stereo program, select “MONO”. The sound becomes monaural, but the noise is reduced.

• If the sound is distorted when receiving a monaural program through the 8 (antenna) terminal, press A/B repeatedly until “MONO” appears on the screen. To cancel the monaural sound setting, press A/B again until “AUTO” appears on the screen.

stereo

JUMP

NICAM

PROGR

bilingual

NICAM monaural

When receiving an A2 program

Broadcasting On-screen display (Selected sound)

A2 stereo

A2 bilingual

NICAM

(Stereo sound)

NICAM MAIN

NICAM SUB

(Main sound)

(Sub sound)

NICAM MAIN (Main sound)

MONO

(Regular sound)

MAIN

(Main sound)

MONO

(Regular sound)

MONO

(Regular sound)

MONO

(Regular sound)

STEREO

(Stereo sound)

SUB

(Sub sound)

Viewing Teletext

KV-TG21M61 only

Some TV stations broadcast an information service called Teletext which allows you to receive various information, such as stock market reports and news.

You can use the buttons on the remote to view Teletext.

To Do this

display a Teletext Press . Each time you press , the page on the screen changes as follows:

TV picture Teletext t Teletext and TV t TV.

JUMP

PROGR

check the contents Press . of a Teletext service An overview of the Teletext contents,

select a Teletext page Press the number buttons to enter the

hold (pause) a Press to display the symbol “z” at Teletext display the top left corner of the screen. To

reveal concealed Press . information (e.g., To conceal the information, press the an answer to a quiz) button again.

enlarge the Teletext Press . Each time you press , the display Teletext display changes as follows:

stand by for a Teletext 1 Enter the Teletext page number that page while watching you want to refer to, then press a TV program 2 When the page number is displayed,

select a FASTEXT Press x (red, green, yellow and blue) menu or the colored that corresponds to the desired menu or boxes page number.

If there is no Teletext broadcast, “100” is displayed at the top left corner of the screen.

including page numbers, appears on the screen.

three-digit page number of the desired Teletext page. If you make a mistake, reenter the correct page number. To access the next or previous page, press PROGR +/–.

resume normal Teletext viewing, press

or .

Enlarge upper half t Enlarge lower half t Normal size.

press

to show the text.

x (red,

green,

yellow,

blue)

SOUND MODE

FAVORITE

turn off Teletext Press a.

Note

• The FASTEXT feature can be used only when the FASTEXT broadcast is available.

– 10 –

One screw (+BVTP 3 × 12)

1 Push to direction of arrow

and remove

2-1. REAR COVER REMOVAL

1 Seven screws

(+BVTP 4 × 16)

1 Rear Cover

1 Four screws

washer head (BVTP 3 × 12)

Speaker

Push claw

1 One screw

(+BVTP 4 × 16)

2 Terminal Bracket

– 11 –

SECTION 2

DISASSEMBLY

2-2. SPEAKER REMOVAL

2-3. CHASSIS ASSY REMOVAL

2-4. SERVICE POSITION

Caution:

standing position.

Note:

placing the chassis into Service Position.

Do not take out CRT support block while TV set in

Undress necessary wires that creates tension while

2-5. TERMINAL BRACKET REMOVAL

2-6. REPLACEMENT OF PARTS

For replacements of light guide,unscrew them, exchange with new parts and fix them with screws respectively.

2-6-1. Replacement of Light Guide

KV-PG21P40/PG21M70/PG21P70

2-6-2. Replacement of Power Button

RM-952

KV-PG21P40/PG21M70/PG21P70

!™

!£

8 Demagnetic coil

4 Four screws

(washer head) (BVTP 3 × 12)

!º Two screws

(Tapping 5+ Crown Washer)

3 Speaker

(5 × 9cm)

6 Tension

spring

7 Chassis assy

5 Deflection

yoke

2 CV board

1 Anode cap

Coating earth assy

!∞ Picture tube

!¢ Cushion

Two screws (Tapping 5 + Crown Washer)

!¡

Holder DGC

Cushion (50x550) DGC

Cushion (35x250) DGC

A Board

CRT Support Block

Slim Beznet

CRT Support Block

Screw Location

Anode button

– 12 –

2-7. PICTURE TUBE REMOVAL

Note:

• Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom right and left.

• REMOVAL OF ANODE-CAP

NOTE : After removing the anode, short circuit the anode of the picture tube and

the anode cap to the metal chassis, CRT shield or carbon paint on the CRT.

• REMOVING PROCEDURES

RM-952

1 Turn up one side of the rubber cap in the direction indicated by the arrow a.

2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.

3 When one side of the rubber cap is separated from the anode button, the anode-cap

can be removed by turning up the rubber cap and pulling it up in the direction of the arrow c.

• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with sharp shaped objects. 2 Do not press the rubber too hard so as not to damage the inside of anode-cap.

A metal fitting called the shatter-hook terminal is built into the rubber.

3 Do not turn the foot of rubber over too hard.

The shatter-hook terminal will stick out or damage the rubber.

SECTION 3

SET-UP ADJUSTMENTS

KV-PG21P40/PG21M70/PG21P70

RM-952

The following adjustments should be made when a complete

realignment is required or a new picture tube is installed.

These adjustments should be performed with rated power

supply voltage unless otherwise noted.

Controls and switches should be set as follows unless otherwise

noted:

PICTURE control ........................................................... normal

BRIGHTNESS control................................................... normal

................................................................................................................................................................................................................................

Preparation :

In order to reduce the influence of geomagnetism on the set's picture tube, face it east or west. Switch on the set's power and degauss with the degausser.

Perform the adjustments in the following order :

1. Beam Landing

2. Convergence

3. Focus

4. White Balance

Note : Test Equipment Required.

1. Pattern Generator

2. Degausser

3. Oscilloscope

Purity control

3-1. BEAM LANDING

1. Input a white signal with the pattern generator. Contrast Brightness

2. Set the pattern generator raster signal to a green raster.

3. Move the deflection yoke to the rear and adjust with the purity control so that the green is at the center and the blue and the red take up equally sized areas on each side. (See Figures 3-1 through 3-4.)

4. Move the deflection yoke forward and adjust so that the entire screen is green. (See Figure 3-1.)

5. Switch the raster signal to blue, then to red and verify the condition.

6. When the position of the deflection yoke has been decided, fasten the deflection yoke with the screws and DY spacers.

7. If the beam does not land correctly in all the corners, use a magnet to adjust it. (See Figure 3-4.)

}

normal

Fig. 3-2

Blue

Red

Green

Fig. 3-3

Fig. 3-1

Purity control corrects this area.

Deflection yoke positioning corrects these areas.

Fig. 3-4

Disk magnets or rotatable disk magnets correct these areas (a-d).

– 13 –

KV-PG21P40/PG21M70/PG21P70

RM-952

3-2. CONVERGENCE

Preparation :

• Before starting this adjustment, adjust the focus, horizontal size and vertical size.

• Receive dot/hatch signal.

• Pic mode: Soft.

(1) Horizontal and Vertical Static Convergence

Center dot

R G B

H. STAT VR

V. STAT

Magnet

RV702

H. STAT

• Operation of V. Stat magnet If the V. Stat magnet is moved in the "a" and "b" arrows, the red, green and blue dots move as shown below.

b b

RGGBB

CV Board

1. (Moving vertically), adjust the V.STAT magnet so that the red, green and blue dots are on top of each other at the center of the screen.

2. (Moving horizontally), adjust the H.STAT VR control so that the red, green and blue dots are on top of each other at the center of the screen.

3. If the H.STAT variable resistor cannot bring the red, green and blue dots together at the center of the screen, adjust the horizontal convergence with the H.STAT variable resistor and the V.STAT magnet in the manner given below. (In this case, the H.STAT variable resistor and the V.STAT magnet influence each other, so be sure to perform adjustments while tracking.)

BMCPurity

BMC (Hexapole)

Purity

4 BMC (Hexapole) Magnet.

If the red, green and blue dots are not balanced or aligned, then use the BMC magnet to adjust in the manner described below.

RG B R G B R GB

DY pocket

V.STAT

– 14 –

+ 34 hidden pages

Sony KV-PG21M70, KV-PG21P40L, KV-PG21P40N, KV-PG21P40, KV-PG21P70 Service Manual

REVISION HISTORY

KV-PG21M70 RM-952 E SCC-U68A-A KV-PG21P40/L RM-952 Malaysia SCC-U71A-A

SPECIFICATIONS

TABLE OF CONTENTS

SELF DIAGNOSTIC FUNCTION

GENERAL

DISASSEMBLY

• REMOVAL OF ANODE-CAP

SET-UP ADJUSTMENTS

3-1. BEAM LANDING

3-2. CONVERGENCE