Sony KV-PF14DK7, KV-PF14L70, KV-PF14M40, KV-PF14M70, KV-PF14P10 Service manual

...
Self Diagnosis
Supported model
SERVICE MANUAL
MODEL COMMANDER DEST. CHASSIS NO.

KV-PF14DK7 RM-952 ME SCC-U30H-A KV-PF14L70 RM-952 ME SCC-U30M-A KV-PF14M40 RM-952 GE SCC-U12Q-A KV-PF14M70 RM-952 E SCC-U13J-A KV-PF14M70 RM-952 E SCC-U13J-A KV-PF14M70 RM-952 Hong Kong SCC-U17K-A

MODEL COMMANDER DEST. CHASSIS NO.
KV-PF14M70 RM-952 ME SCC-U30K-A KV-PF14P10 RM-952 OCE SCC-U2AE-A KV-PF14P70 RM-952 E SCC-U13G-A KV-PF14Q70 RM-952 E SCC-U13K-A KV-PF14Q70 RM-952 ME SCC-U30F-A
BG-3S
CHASSIS
TRINITRON
®
COLOR TV
KV -PF14DK7/PF14L70/PF14M40/PF14M70 KV -PF14P10/PF14P70/PF14Q70
RM-952
Power requirements 110-240 V AC, 50/60 Hz
220-240V AC, 50/60Hz Hong Kong/OCE
Power consumption (W) Indicated on the rear of the TV Television system B/G KV-PF14L70/PF14P10/
B/G, I, D/K, M KV-PF14M40/PF14M70
Color system PAL, PAL60, SECAM, NTSC4.43 KV-PF14Q70
PAL, PAL60, NTSC4.43, NTSC3.58 (AV IN) KV-PF14P70/PF14P10 PAL, PAL60, SECAM, NTSC4.43, NTSC3.58 (AV IN) KV-PF14L70 PAL, PAL60, SECAM, NTSC4.43, NTSC3.58 KV-PF14M40/PF14M70
Channel coverage
B/G VHF : E2 to E12
UHF : E21 to E69 CATV : S01 to S03, S1 to S41
I UHF : B21 to B68
CATV : S01 to S03, S1 to S41 KV-PF14M40/PF14M70
D/K VHF : C1 to C12, R1 to R12
UHF : C13 to C57 CATV : S01 to S03, S1 to S41, Z1 to Z39 KV-PF14M40/PF14M70
M VHF : A2 to A3
UHF : A14 to A79 CATV : A-8 to A-2, A-2 to W+4, W+60 to W+84 KV-PF14M40/PF14M70
˘˘
˘ (Antenna) 75-ohm external terinal
˘˘
Audio output 3W Number of terminal
(Video) Input : 2 Output : 1 Phono jacks; 1 Vp-p, 75 ohms (Audio) Input : 2 Output : 1 Phono jacks; 500 mVrms (Earphone) Output : 1 Minijack
Ø
Picture tube 14 inch
Tube size (cm) 37 Measured diagonally
Screen size (cm) 34 Measured diagonally Dimension (w/h/d, mm) 375 x 346 x 416 Mass (kg) 13

SPECIFICATIONS

Note
KV-PF14P70/PF14Q70
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE SCHEMA TIC DIA GRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL TO SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED.
– 2 –

TABLE OF CONTENTS

KV -PF14DK7/PF14L70/PF14M40/PF14M70 KV -PF14P10/PF14P70/PF14Q70
RM-952
Section Title Page
SELF DIAGNOSIS FUNCTION................................ 4
1. GENERAL .......................................................... 8
2. DISASSEMBLY
2-1. Rear Cover Removal................................................ 19
2-2. Chassis Assy Removal ............................................. 19
2-3. F Bracket Removal .................................................. 19
2-4. Service Position ....................................................... 19
2-5. Replacement of Parts ............................................... 20
2-5-1. Replacement of Control Button ....................... 20
2-5-2. Replacement of Bar Optical ............................. 20
2-6. Terminal Bracket Removal ...................................... 20
2-7. Degauss Coil Removal............................................. 20
2-8. Picture Tube Removal.............................................. 21
3. SET-UP ADJUSTMENTS
3-1. Beam Landing.......................................................... 22
3-2. Convergence............................................................. 23
3-3. Focus Adjustment .................................................... 25
3-4. G2 (Screen) and White Balance Adjustments......... 25
Section Title Page
5. DIAGRAMS
5-1 Block Diagram ......................................................... 37
5-2 Frame Schematic Diagram ...................................... 40
5-3 Circuit Boards Location .......................................... 42
5-4 Schematic Diagrams and Printed Wiring Boards ... 43
(1) Schematic Diagram of A(1/2) Board ................................. 45
(2) Scheamtic Diagram of A(2/2) Board ................................. 49
(3) Schematic Diagrams of C3 and F Boards ......................... 56
5-5 Semicondutors ......................................................... 61
6. EXPLODED VIEWS
6-1. Chassis ..................................................................... 64
7. ELECTRICAL PARTS LIST ............................... 66
4. CIRCUIT ADJUSTMENTS
4-1. Adjustments with Commander................................ 26
4-2. Adjustment Method ................................................. 27
4-3. Picture Quality Adjustments.................................... 32
4-4. A Board Adjustment After IC003 (Memory)
Replacement............................................................. 32
4-5. Picture Distortion Adjustment ................................. 33
– 3 –
KV -PF14DK7/PF14L70/PF14M40/PF14M70 KV -PF14P10/PF14P70/PF14Q70
RM-952

SELF DIAGNOSTIC FUNCTION

The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICA TORS
When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.
Diagnostic
Item
Description
• Power does not turn on
• +B overcurrent (OCP) or overvoltage (OVP)
• Vertical deflection stopped
• Horizontal deflection overdrive
• White balance failure (no PICTURE)
• Micro reset
No. of times
STANDBY/TIMER
lamp flashes
Does not light
2 times
5 times
Self-diagnostic
display/Diagnostic
result
002:000 or 002:001~255 003:001~255 004:001~255
at the same time
005:000 or 005:001~225
101:00 or
101:001~225
Probable
Cause
Location
• Power cord is not plugged in.
• Fuse is burned out F4601 (F board)
• H.OUT Q511 is shorted. (A board)
• -13V is not supplied. (A board)
• IC 503 faulty (A board)
• G2 is improperly adjusted. (Note 2)
• CRT problem.
• IC301 is faulty. (A board)
• No connection A board to C3 board.
• Discharge CRT (C3 Board)
• Static discharge
• External noise
Detected
Symptoms
• Power does not come on.
• No power is supplied to the TV.
• AC power supply is faulty.
• Power does not come on.
• Load on power line is shorted.
• Has entered standby state after horizontal raster.
• Vertical deflection pulse is stopped.
• Power line is shorted or power supply is stopped.
• No raster is generated.
• CRT cathode current detection reference pulse output is small.
• Power is shut down shortly, after this return back to normal.
• Detect Micro latch up.
Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.
The symptom that is diagnosed first by the microcontroller is displayed on the screen.
Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.
– 4 –
2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT
2 times
5 times
KV -PF14DK7/PF14L70/PF14M40/PF14M70 KV -PF14P10/PF14P70/PF14Q70
RM-952
Lamp ON 0.3 sec. Lamp OFF 0.3 sec.
Diagnostic Item Flash Count* +B overcurrent/overvoltage 2 times Vertical deflection stopped
White balance failure 5 times * One flash count is not used for self-diagnostic.
Lamp OFF 3 sec.
STANDBY/SLEEP lamp
3. STOPPING THE STANDBY/TIMER FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp from flashing.
– 5 –
KV -PF14DK7/PF14L70/PF14M40/PF14M70 KV -PF14P10/PF14P70/PF14Q70
RM-952
4. SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as power sometimes shuts off or screen sometimes goes out that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screendisplay] / channel [5] / Sound volume [-] / Power ON
˘
Note that this differs from entering the service mode (mode volume [+]).
Self-Diagnosis screen display
SELF DIAGNOSTIC
002 : 000 003 : 000 004 : 000 005 : 001
101 : 000
Numeral "0" means that no fault has been detected.
Numeral "1" means a fault has been detected.
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic screen is being displayed.
Channel [8] / 0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
– 6 –
6. SELF-DIAGNOSTIC CIRCUIT
KV -PF14DK7/PF14L70/PF14M40/PF14M70 KV -PF14P10/PF14P70/PF14Q70
RM-952
FROM
CRT
FROM
[+B] Q604 C3
[V] Q509/507
IC301
Y/CHROMA JUNGLE
IK-IN
MP/
18 51
PROTECT
SDA
4635
IC001
SYSTEM
IO-8DAT
O-LED
IO-SDAT
MEMORY
54521
B-DAT
IC003
[+BovercurrentªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven verticals in a period, the unit will automatically turn off.
[Verticaldeflectionstopped] Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.
[Verticaldeflectionovercurrent] Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.
[Whitebalancefailure] If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301. TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
– 7 –
KV -PF14DK7/PF14L70/PF14M40/PF14M70
2
WARNING
• Dangerously high voltages are present inside the TV.
• TV operating voltage: 110 – 240 V AC. (For Hong Kong/OCE: 220 – 240 V AC.)
To prevent fire or shock hazard, do not expose the TV to rain or moisture.
Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only.
Do not open the cabinet and the rear cover of the TV. Refer servicing to qualified personnel.
Do not install the TV in hot, humid or excessively dusty places.
Do not install the TV in a confined space, such as a bookcase or built-in cabinet. Do not block the ventilation openings of the TV.
Do not pull the power cord to disconnect the TV. Pull it out by the plug.
Disconnect the power cord during lightning storms or if you are not going to use the TV for several days.
Install the TV in a stable position. Do not allow children to climb onto it.
Do not plug in too many appliances to the same power socket. Do not damage the power cord.
Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not scratch the picture tube.
4
Using Your New TV
Getting Started
Step 1
Connect the antenna
If you wish to connect a VCR, see the
Connecting a VCR
diagram below
.
Using Your New TV
IEC connector (not supplied)
To video and audio outputs
VCR
(yellow)
(black)
Antenna cable (not supplied)
To 1 (video input)
Audio/Video cable (not supplied)
: Signal flow
To antenna output
Antenna cable (not supplied)
Rear of TV
Connecting a VCR
To watch the video, press
(see page 12).
or
: Signal flow
VIDEO
VIDEO IN
VIDEO OUT
AUDIO
1
Rear of TV
To ˘ (antenna)
KV -PF14P10/PF14P70/PF14Q70
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
– 8 –
SECTION 1

GENERAL

RM-952
5
Using Your New TV
Using Your New TV
Preset the channels automatically
Tips
If you want to stop automatic channel presetting, press SELECT twice.
If your TV has preset an unwanted channel or cannot preset a particular
channel, then preset your TV manually (see page 9).
Note (KV-PF14DK7/PF14M40/PF14M70)
During automatic channel presetting, your TV screen will indicate
B/G”,
I”, “D/K or M for the TV system.
Now You Are Ready. . .
To watch your TV, see page 11.
Notes
If you connect a stereo VCR, connect the yellow plug to
(the yellow
jack) and the white plug to
(the black jack).
If you connect a VCR to the ˘ (antenna) terminal, preset the signal output from the VCR to the program number 0 on the TV.
When no signal is input to the connected video equipment, the TV screen becomes blue.
Step 2
Note
Do not use old batteries nor use different types of batteries together.
Step 3
CAUTION
Do not connect the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground.
Insert the batteries into the remote
Front of TV
1
1
1
2
VHF
LOW
B/G
6
Using Your New TV
Connecting optional components
You can connect optional video components, such as a VCR, multi disc player, camcorder or video game.
To watch the picture of the connected equipment, press
(see page 12).
Connecting a camcorder/video game equipment using the (video input) jacks
Note
You can also connect video equipment to the … 1 (video input) jacks at the rear of your TV.
Connecting video equipment using the Ú (monitor output) jacks
Note
When connecting a stereo VCR, connect the yellow plug to
(the yellow
jack) and the white plug to
(the black jack).
Front of TV
Camcorder
Video game equipment
To video and audio outputs
(yellow)
(black)
Rear of TV
To antenna outputVCR
: Signal flow
To
2
(video input)
To Ú (monitor output)
or
Audio/Video cable (not supplied)
Antenna cable (not supplied)
2
1
Audio/Video cable (not supplied)
: Signal flow
To video and audio inputs
9
KV -PF14DK7/PF14L70/PF14M40/PF14M70
KV -PF14P10/PF14P70/PF14Q70
RM-952
8
Using Your New TV
TV
1
2
3
4
6
7
8
9
÷
0
5
JUMP
SOUND
MODE
FAVORITE
PROGR
Á
Presetting channels
You can preset up to 100 TV channels in numerical sequence from program number 1 using the remote and the buttons on your TV as well.
Presetting channels automatically
1
Press U to turn on the TV.
2
Press AUTO PROGR.
Note (KV-PF14DK7/PF14M40/PF14M70)
During automatic channel presetting, your TV screen will indicate
B/G”,
I”, “D/K or M for the TV system.
To preset channels automatically from a specified program number
(1) Press SELECT until
AUT
O PROGRAM” appears.
(2) Press + or –.
The on-screen display will start flashing.
(3) Press PROGR +/– or the number buttons until the desir
ed program number
appears.
(4) Press + or –.
u
Number buttons
SELECT
. +/–
PROGR +/–
+ or –
PIC MODE
VHF
LOW
B/G
7
Using Your New TV
Using Your New TV
Securing the TV
To prevent the TV from falling, secure the TV using one of the following methods:
A
With the supplied screws, attach the band to the TV stand and to the rear of the TV using the provided hole.
or
B
Put the cord or chain through the clamps to secure the TV against a wall or pillar.
Note
Use only the supplied screws. Use of other screws may damage the TV.
20 mm
A
B
3.8mm
or
10
KV -PF14DK7/PF14L70/PF14M40/PF14M70
KV -PF14P10/PF14P70/PF14Q70
RM-952
9
Using Your New TV
Using Your New TV
Presetting channels manually
1
Press SELECT until “MANUAL PROGRAM” appears.
2
Press + or –.
3
Press PROGR +/– or the number buttons until the desired program number appears.
4
Press + or – until the desired channel picture appears.
5
Press SELECT.
To change the color system setting
If the color is abnormal when receiving programs through the
˘
(antenna) terminal
or the
(video input) jack
(1) Press SELECT until
COL
SYS” appears.
(2) Press + or – to select the appropriate color
system until the color is optimal.
Tip
Normally set COL SYS to AUTO”.
Note
The color system
SECAM is not available for KV
-PF14P70/PF14P10.
The color system
NTSC3.58 is not available for KV
-PF14Q70.
continued
MANUAL PROGRAM
SELECT
VHF
LOW
B/G
or
1
2
3
4
5
6
7
8 0
-/--
9
PROGR
1
SELECT
COL SYS: AUTO
AUTO
PAL SECAM
NTSC 3.58
NTSC 4.43
10
Using Your New TV
To change the TV system setting (KV-PF14M40/PF14M70 only)
If the picture or sound is abnormal when receiving programs through the
˘
(antenna)
terminal (1) Press SELECT until
TV SYS appears.
(2) Press + or – to select the appropriate
TV system until the picture or sound quality is optimal.
Skipping program numbers
1
Press PROGR +/
– or the number buttons until the unused or unwanted
program number appears.
2
Press SELECT until
MANUAL PROGRAM
appears.
3
Press + or –.
4
Press PIC MODE.
5
Press SELECT.
To preset the skipped program number again
Preset the channel automatically or manually.
Tip
You can also use SELECT and
¸
+/– on the TV to preset channels and
skip program numbers.
To use the fine tuning (FINE) function
The fine tuning (FINE) function may help to reduce the following problems: double images and lines moving across the TV screen.
You can use the fine tuning function as below: (1) Select the program number you want to adjust.
(2) Press SELECT until
MANUAL
PROGRAM” appears on the screen. (3) Press + or – on the remote control once. (4) Press
to display “FINE” on the scr
een.
(5) Press + or – continuously until the above problems are minimized.
The + or – icon on the screen flashes while tuning.
(6) Press SELECT to return to normal screen.
Presetting channels (continued)
TV SYS: B/G
B/G
I
D/K M
11
KV -PF14DK7/PF14L70/PF14M40/PF14M70
KV -PF14P10/PF14P70/PF14Q70
RM-952
12
Using Your New TV
To
Turn off temporarily Turn off completely Mute the sound Watch the video input
(VCR, camcorder, etc.) Jump back to the previous channel Display the on-screen information* Adjust the volume of each TV
program automatically
Do this
Press u. The u indicator on the TV lights up red. Press U on the TV. Press ¤. Press
to select VIDEO 1 or VIDEO 2”.
To return to the TV program, press ;. Press JUMP. Press
.
Press SELECT repeatedly until
INTELLIGENT VOL
appears, then press + or – to select “ON”. To cancel, select “OFF”.
* The picture, sound, and either the program number or video mode are
displayed. The on-screen display for the picture and sound information disappears after about 3 seconds.
Changing the on-screen display language (except KV-PF14DK7/PF14L70/PF14M70(ME)/PF14Q70(ME))
1
Press SELECT until LANGUAGE /
: ENGLISHappears on the screen.
2
Press + or to select
“.
Tip
You can also use SELECT and . +/ on the TV to select the on-screen display language.
Additional tasks
Watching the TV (continued)
SELECT
LANGUAGE /
: ENGLISH
/ LANGUAGE
:
11
Using Your New TV
Using Your New TV
TV
1
2
3
4
6
7
8
9
÷
0
5
JUMP
SOUND
MODE
FAVORITE
PROGR
Á
Watching the TV
This section explains functions used while watching the TV. Most operations can be done using the remote.
1
Press U to turn on the TV.
When the TV is in the standby mode (the u indicator on the TV is lit red), press u on the remote or PROGR +/– on the TV
.
2
Press PROGR +/
– or the number buttons to select the TV program.
For double digit numbers, press ÷, then the number (e.g., for 25, press ÷, then 2 and 5).
3
Press
. +/– to adjust the
volume.
¤
u
;
Number buttons
SELECT
. +/–
PROGR +/–
+ or –
JUMP
or
continued
1
2
3
4
5
6
7
8 0
-/--
9
PROGR
– 12 –
KV -PF14DK7/PF14L70/PF14M40/PF14M70
KV -PF14P10/PF14P70/PF14Q70
RM-952
12
Using Your New TV
To
Turn of f temporarily Turn off completely Mute the sound Watch the video input
(VCR, camcorder, etc.) Jump back to the previous channel Display the on-screen information* Adjust the volume of each TV
program automatically
Do this
Press u. The u indicator on the TV lights up red. Press U on the TV. Press ¤. Press
to select VIDEO 1 or VIDEO 2”.
To return to the TV program, press ;. Press JUMP. Press
.
Press SELECT repeatedly until
INTELLIGENT VOL
appears, then press + or – to select “ON”. To cancel, select “OFF”.
* The picture, sound, and either the program number or video mode are
displayed. The on-screen display for the picture and sound information disappears after about 3 seconds.
Changing the on-screen display language (KV-PF14DK7/PF14L70/PF14M70(ME)/PF14Q70(ME))
1
Press SELECT until LANGUAGE /
: ENGLISHappears on the screen.
2
Press + or to select
“.
Tip
You can also use SELECT and . +/ on the TV to select the on-screen display language.
Additional tasks
Watching the TV (continued)
LANGUAGE / : ENGLISH
SELECT
LANGUAGE / :
13
Using Your New TV
Using Your New TV
Setting the Wake Up timer
1
Press
until the desired period of time appears.
2
Select the TV program or video mode you want to display when you wake up.
3
Press u or set the Sleep timer if you want the TV to turn off automatically.
The
indicator on the TV lights up orange.
To cancel the Wake Up timer
Press until WAKE UP TIMER: OFF appears or turn off the TVs main power.
Notes
The Wake Up timer starts immediately after the on-screen display disappears.
If no buttons or controls are pressed for more than two hours after the TV is turned on using the Wake Up timer, the TV automatically goes into the standby mode. To continue watching the TV, press any button or control on the TV or the remote.
Setting the Sleep timer
Press until the desired period of time appears.
To cancel the Sleep timer
Press until SLEEP TIMER: OFF appears or turn the TV off.
WAKE UP TIMER:10M
WAKE UP TIMER:OFF
WAKE UP TIMER:12H00M
After 10 minutes
No Wake Up timer After 12 hours
SLEEP TIMER:30M
SLEEP TIMER:60M
SLEEP TIMER:OFF
SLEEP TIMER:90M
After 30 minutes
No Sleep Timer
After 60 minutes
After 90 minutes
13
KV -PF14DK7/PF14L70/PF14M40/PF14M70
KV -PF14P10/PF14P70/PF14Q70
RM-952
14
Advanced Operations
SOUND
MODE
FAVORITE
PROGR
Á
Advanced Operations
SOUND MODE
Customizing the picture and sound
You can customize the picture and sound by selecting the picture and sound modes or by adjusting its settings.
Selecting the picture and sound modes
To select the picture mode
Press PIC MODE repeatedly until you get the desired picture mode.
Select To
DYNAMIC receive high contrast pictures. STANDARD receive normal contrast pictures. SOFT receive mild pictures.
To select the sound mode
Press SOUND MODE repeatedly until you get the desired sound mode.
Select To
DYNAMIC listen to dynamic and clear sound that emphasizes the low and
high sound. DRAMA listen to sound that emphasizes vocals and background music. SOFT receive soft sound.
PIC MODE
SELECT
+ or –
STANDARDDYNAMIC
SOFT
PIC MODE
DYNAMIC
DRAMA SOFT
SOUND
MODE
15
Advanced Operations
Advanced Operations
Adjusting the picture and sound settings
1
Press SELECT until the desired setting appears.
Each time you press SELECT, the setting item will change as follows:
2
Press + or – to adjust the item.
3
To adjust other items, repeat steps 1 to 2.
* HUE can be adjusted for the NTSC system only.
Notes
When you select a picture or sound mode, the adjusted settings will be reset according to the selected mode.
You can also use SELECT and
¸
+/– on the TV to adjust the picture and
sound settings.
SELECT
PICTURE
60
PICTURE COLOR
BRIGHT
HUE*
TREBLE BASS
SHARP
14
KV -PF14DK7/PF14L70/PF14M40/PF14M70
KV -PF14P10/PF14P70/PF14Q70
RM-952
16
Advanced Operations
TV
1
2
3
4
6
7
8
9
÷
0
5
JUMP
SOUND
MODE
FAVORITE
PROGR
Á
Blocking the channels (CHILD LOCK)
You can prevent a child from watching certain programs by using the buttons on the remote control.
1
Select the TV program you want to lock.
2
Press SELECT until
CHILD LOCK appears on the screen.
3
Press + or to selectON”.
The
symbol appears on
the screen. To unlock the channel,
press + or – to select OFF. The
symbol
disappears from the screen.
Note
If you preset a locked channel, that particular channel will be unlocked automatically.
SELECT
+ or –
CHILD LOCK: OFF
SELECT
CHILD LOCK: ON
1
17
Additional Information
Additional Information
Self-diagnosis function
Your TV is equipped with a self-diagnosis function. If there is a problem with your TV, the u indicator flashes red. The number of times the u indicator flashes indicates the possible causes.
1
Check that the u indicator flashes red a number of times between 3-second intervals.
2
Count the number of times the u indicator flashes.
3
Press U (main power) to turn off your TV.
4
Inform your nearest Sony service center about the number of times the u indicator flashes. Be sure to note the model name and serial number located on the rear of your TV.
Front of TV
Additional Information
u indicator
15
KV -PF14DK7/PF14L70/PF14M40/PF14M70
KV -PF14P10/PF14P70/PF14Q70
RM-952
18
Additional Information
Snowy picture
Noisy sound
Distorted picture
Noisy sound
Good picture
Noisy sound
No picture
No sound
Troubleshooting
(except KV-PF14P10)
If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer .
Possible causeSymptom
Solutions
Check the antenna cable and connection on the TV, VCR and on the wall. (page 4)
Press SELECT until
MANUAL
PROGRAM appears on the screen then preset the channel again. (page 9)
Check the antenna type (VHF/UHF).
Contact a Sony dealer for advice.
Adjust the antenna direction. Contact a
Sony dealer for advice.
Try using a booster.
Turn off or disconnect the booster if it is
in use.
If the sound of all the channels are
noisy, check the TV system (TV SYS) setting (page 10), then press AUTO PROGR to preset the channels again (page 8).
If the sound of some channels are noisy,
select the channel, then select the appropriate TV system (TV SYS). (page 10)
Check the power cord, antenna and the
VCR connections.
Press u (power).
Press U (main power) on the TV to turn
off the TV for about five seconds, then turn it on again.
Connection is loose or the cable is damaged.
Channel presetting is inappropriate or incomplete.
The antenna type is inappropriate.
The antenna direction is inappropriate.
Signal transmission is low.
Broadcast signals are too
strong.
The TV system setting or channel presetting is inappropriate or incomplete.
The power cord, antenna or VCR is not connected.
The TV is not turned on.
18
Additional Information
Snowy picture
Noisy sound
Distorted picture
Noisy sound
No picture
No sound
Troubleshooting
(KV-PF14P10 only)
If you find any problem while viewing your TV, please check the following guide. If any problem persists, contact your Sony dealer .
Possible causeSymptom
Solutions
Check the antenna cable and connection on the TV, VCR and on the wall. (page 4)
Press SELECT until
MANUAL
PROGRAM appears on the screen then preset the channel again. (page 9)
Check the antenna type (VHF/UHF). Contact a Sony dealer for advice.
Adjust the antenna direction. Contact a Sony dealer for advice.
Try using a booster.
Turn off or disconnect the booster if it is
in use.
Check the power cord, antenna and the VCR connections.
Press u (power).
Press U (main power) on the TV to turn
off the TV for about five seconds, then turn it on again.
Connection is loose or the cable is damaged.
Channel presetting is inappropriate or incomplete.
The antenna type is inappropriate.
The antenna direction is inappropriate.
Signal transmission is low.
Broadcast signals are too
strong.
The power cord, antenna or VCR is not connected.
The TV is not turned on.
16
KV -PF14DK7/PF14L70/PF14M40/PF14M70
KV -PF14P10/PF14P70/PF14Q70
RM-952
19
Additional Information
Possible causeSymptom
Solutions
continued
Good picture
No sound
Dotted lines or stripes
Double images or ghosts
N
o
color
Abnormal color patches
Press ¸ + to increase the volume level.
Press ¤ to cancel the muting.
Do not use a hair dryer or other
equipment near the TV.
Adjust the antenna direction for minimum interference. Contact a Sony dealer for advice.
Use a highly directional antenna.
Use the fine tuning (FINE) function.
(page 10)
Adjust the antenna direction. Contact a Sony dealer for advice.
Turn off or disconnect the booster if it is in use.
Press SELECT until
COLOR appears
on the screen, then press + or – to adjust the color level. (page 15)
Press SELECT until
COL
SYS appears on the screen, then check the color system setting (usually set this to
AUTO). (page 9).
Adjust the antenna direction. Contact a
Sony dealer for advice.
Keep external speakers or other electrical equipment away from the TV. Do not move the TV while the TV is turned on. Press U (main power) on the TV to turn off the TV for about five minutes, then turn it on again.
The volume level is too low.
The sound is muted.
There is local interference
from cars, neon signs, hair dryers, power generators, etc.
Broadcast signals are reflected by nearby mountains or buildings.
The antenna direction is inappropriate.
Use of a booster is inappropriate.
The color level setting is too low.
The color system setting is inappropriate.
The antenna direction is inappropriate.
The magnetic disturbance from external speakers or other equipment, or the direction of the earth
s magnetic field may affect the TV.
20
Additional Information
Lines moving across the TV screen.
The
u
indicator on your TV flashes red a number of times between 3-second intervals.
TV cabinet creaks.
A “boom” sound is heard when the TV is turned on.
T roubleshooting (continued)
Possible causeSymptom
Solutions
Use the fine tuning (FINE) function. (page 10)
Contact your nearest Sony service
center. (page 17)
There is interference from
external sources, e.g., heavy machineries, nearby broadcast station.
Your TV may need service.
Changes in room
temperature sometimes make the TV cabinet expand or contract, making a noise. This does not indicate a malfunction.
The TVs demagnetizing function is working. This does not indicate a malfunction.
17
KV -PF14DK7/PF14L70/PF14M40/PF14M70
KV -PF14P10/PF14P70/PF14Q70
RM-952
Loading...
+ 37 hidden pages