Sony KV-DZ29M30, KV-DZ29M61, KV-DZ29M91 Schematic
REVISION HISTORY
CX2
CHASSIS
MODEL
KV-DZ29M30
KV-DZ29M61
KV-DZ29M61
KV-DZ29M91
NO. SUFFIX DATE SUPP / CORR DESCRIPTION
1 -01 2006/08 _ _ 1st Issue
PA RT NO. : 9-872-925-01
SERVICE MANUAL
CX2
CHASSIS
MODEL COMMANDER DEST. CHASSIS NO.
KV-DZ29M30 RM-GA002 South Africa SCC-V77A-A
KV-DZ29M61 RM-GA002 Malaysia SCC-V78A-A
KV-DZ29M61 RM-GA002 GE SCC-V72A-A
KV-DZ29M91 RM-GA002 Russia SCC-V74A-A
MODEL COMMANDER DEST. CHASSIS NO.
RM-GA002
TRINITRON
®
COLOR TV
KV-DZ29M30/M61/M91
RM-GA002
TABLE OF CONTENTS
Section Title Page
SELF DIAGNOSTIC FUNCTION..................................3
1. DISASSEMBLY
1-1. Rear Cover Removal .................................................. 5
1-2. Speaker Removal ....................................................... 5
1-3. Chassis Assy Removal ............................................... 5
1-4. Service Position ......................................................... 5
1-5. D and D3 Boards Removal ........................................ 5
1-6. F1 Board Removal ..................................................... 5
1-7. H1 Board Removal .................................................... 6
1-8. A1 and B1 Boards Removal ...................................... 6
1-9. Picture Tube Removal................................................ 6
2. CIRCUIT BOARDS LOCATION ...................................8
3. ADVANCE OPERATION
3-1. "RESET" Function ..................................................... 9
4. SET-UP ADJUSTMENTS
4-1. Beam Landing Adjustment ...................................... 10
4-2. Convergence Adjustment ......................................... 11
4-3. Focus Adjustment .................................................... 13
4-4. G2 (SCREEN) Adjustments .................................... 13
4-5. Sub Brightness Adjustment ..................................... 13
4-6. White Balance Adjustment ...................................... 13
5. CIRCUIT ADJUSTMENTS
5-1. Adjustment With Commander ................................. 14
5-2. Adjustment Method ................................................. 15
5-3. Picture Quality Adjustments.................................... 48
5-4. Sub Hue/Col Adjustment ......................................... 48
5-5. Deflection Adjustments ........................................... 49
5-6. Picture Distortion Adjustment (1) ........................... 50
Section Title Page
6. DIAGRAMS
6-1. Block Diagram ......................................................... 51
6-2. Schematic Diagram Information ............................. 52
6-2-1. A1 Board – (Block 001)................................ 53
6-2-2. A1 Board – (Block 002)................................ 55
6-2-3. A1 Board – (Block 003)................................ 57
6-2-4. A1 Board – (Block 004)................................ 59
6-2-5. B1 Board – (Block 001) ................................ 60
6-2-6. B1 Board – (Block 002) ................................ 62
6-2-7. C Board Schematic Diagram ........................ 64
6-2-8. D Board – (Block 001) ................................. 66
6-2-9. D Board – (Block 002) ................................. 68
6-2-10. D3 Board Schematic Diagram .................... 69
6-2-11. F1 Board Schematic Diagram .................... 71
6-2-12. H1 Board Schematic Diagram .................... 72
6-2-13. VM1 Board Schematic Diagram ................ 74
6-3. Voltage Measurement and Waveform ...................... 76
6-4. Printed Wiring Boards ............................................. 82
6-5. Semiconductors ........................................................ 89
7. EXPLODED VIEWS
7-1. Picture Tube and Speaker Bracket .......................... 91
8. ELECTRICAL PARTS LIST........................................ 93
OPERATING INSTRUCTIONS
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE
ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE
SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
– 2 –
KV-DZ29M30/M61/M91
SELF DIAGNOSTIC FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically
begin to flash.
The number of times the lamp flashes translates to a probable source of the problem. If an error symptom cannot be
reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past
problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICATORS
When an error occurs, the STANDBY/TIMER lamp will flash a number of times to indicate the possible cause of the problem.
If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.
RM-GA002
Diagnostic
Item
Description
• Power does not
turn on
• +B overcurrent
(OCP)
• Horizontal
deflection failure
• +B overvoltage
(OVP)
• Vertical deflection
failure
• White balance
failure (no
PICTURE)
• 5V/9V failure
• Micro reset
• BT Power
Failure
No. of times
STANDBY/TIMER
lamp flashes
Does not light
2 times
3 times
4 times
5 times
8 times
—
9 times
Self-diagnostic
display/Diagnostic
result
—
2 OCP :000 or
2 OCP :001~255
3 OVP :000 or
3 OVP :001~255
4 VSTOP :000 or
4 VSTOP :001~255
5 AKB :000 or
5 AKB :001~255
8 SUP :0001 or
8 SUP :001~225
101 WDT :N/A
9 SUPBT:000 or
9 SUPBT :001~255
Probable
Cause
Location
• Power cord is not plugged in.
• Fuse is burned out F1601
(F1 Board)
• H.OUT Q6802 is shorted.
• PS6606 open, PS6605 open.
(D board)
• PH6602 faulty.
D6644 faulty, R6688 open.
• 10.5V is not supplied.
(D board)
• V.OUT IC6800 faulty
D6827 faulty
D6817 faulty
R6850 open
R6872 open (D board)
• G2 is improperly adjusted.
• CRT problem.
• Video OUT IC9001, 9002,
9003 are faulty. (C board)
• IC4301 CXA2170Q
(A1 board) are faulty.
• 5V regulator (IC2601) faulty.
• 9V regulator (IC2600) faulty.
• CRT Discharge (C Board)
• Static discharge
• External noise
BT MCV Failure
Detected
Symptoms
• Power does not turn on.
• No power is supplied to the
TV.
• AC power supply is faulty.
• Power does not turn on.
• Load on power line is
shorted.
• H pulse output is too high.
• Power does not come on.
• Vertical deflection pulse is
stopped.
• Vertical size is too small.
• Vertical deflection stopped.
• No raster is generated.
• CRT cathode current
detection reference pulse
output is small.
• TV Blank
• No Raster
• Power is shut down shortly,
after this return back to
normal.
• Detect Micro latch up.
• TV Blank
• No Raster
2. STANDBY INDICATOR BLINKING PROCESS
Lamp ON 300ms
Lamp OFF 300ms
The example above represents for 4 times blink
Lamp OFF 3 seconds
3. STANDBY INDICATOR ON TV FRONT PANEL
Standby indicator
– 3 –
KV-DZ29M30/M61/M91
RM-GA002
4. SELF DIAGNOSTIC SCREEN DISPLAY
SELF DIAGNOSTIC
2 OCP: 0
3 OVP: 0
4 VSTOP: 0
5 AKB: 0
8 SOP: 0
9 SOPBT: 0
01 WDT: N/A
5. HANDLING SELF DIAGNOSTIC SCREEN DISPLAY
No. Description Method
1. Display self diagnostic screen [Display] t [Channel ] t [Volume ] t [Power / TV]
2. Stop standby flash i) Turn off power switch on main.
3. Clear fault result In self diagnostic screen, press [Channel ] t -
4. Quit self diagnostic screen Turn off power switch of remote commander or main unit.
Numeral "0" means that no fault has been detected.
Numeral "1" means a fault has been detected.
Numeral "2" means two faults have been detected.
5
Note: The above must be performed while TV is on standby mode.
ii) Unplug power cord from the outlet.
8
Note: Diagnostic results display on screen is not automatically cleared. Therefore,
clear result after completion of repair.
6. SELF-DIAGNOSTIC CIRCUIT
FROM
CRT (IK)
[OCP] Q6804, D6821
[H] D6808, D6809
[V] Q6808, R6910
IC4301
RGB JUNGLE
IK_IN
57
H PROT
56
V PROT
CXA2170AQ
OVP
SDA
SYSTEM
6
9V
IC001
84
RED LED
5V
14,47,
82
IC004
MEMORY
SDA
7
524
[+B overcurrent OCP ] Occurs when an overcurrent on the +B(135) line is detected by Q6804.
If Q6804 go to ON, the voltage to the pin57 of IC4301 go to "HIGH".
The unit will automatically turn off.
[High voltage protector of Horizontal Deflection] Occurs when an overvoltage of horizontal pulse is detected by D6809.
If the voltage of anode D6809 and D6843 goes to High, the voltage to pin57
of IC4301 go to "HIGH".
The unit will automatically turn off.
[+B overvoltage OVP ] Occurs when an overvoltage on the +B(135) line is detected by D6635 and
Q6606. If Q6606 go to ON, the voltage to pin6 of IC001 go to "HIGH". The
unit will automatically turn off.
[Vertical deflection failure] Occurs when an absence of the vertical deflection pulse is detected by
Q6808 and R6910. Shut down the power supply.
[White balance failure] If the RGB levels do not balance or become low level within 5 seconds. This
error will be detected by IC4301.
TV will stay on, but there will be no picture.
[5V/9V failure] Occurs when 5V/9V is not supplied to Micon (IC001).
No raster will be detected or no picture.
– 4 –
SECTION 1
DISASSEMBLY
KV-DZ29M30/M61/M91
RM-GA002
1-1. REAR COVER REMOVAL
3 Rear cover
1 Eleven screws
(+BVTP 4 × 16)
2 One screw
(+BVTP 3 × 12)
1-2. SPEAKER REMOVAL
1 Two screws
(Washer Head)
(+P4x16)
1-3. CHASSIS ASSY REMOVAL 1-4. SERVICE POSITION
3
One stopper
2
1
One stopper
3 One screw
(+BVTP 3 × 12)
1i& 2 Make sure stopper is release & unscrew one screw
before taking out boards.
• Make sure all connector/bridge are fully inserted during
chassis installation.
1-5. D AND D3 BOARDS REMOVAL
2
1
1 Do not bend A1 board to avoid Bridge connector peel off.
2 Locate paper between A and D board to avoid heat sink touching.
3 Locate paper between A and C board to avoid heat sink touching.
• No need to connect earthing connector (F1 Board) during servicing.
1-6. F1 BOARD REMOVAL
1 Two screws
(+BVTP 3 × 12)
2 D3 Board
1 D Board
2 F1 Board
– 5 –
KV-DZ29M30/M61/M91
RM-GA002
1-8. A1 AND B1 BOARDS REMOVAL1-7. H1 BOARD REMOVAL
1 Two hooks
3 Two clips
2 A1 Board
2 H1 Board
1 Two hooks
4 B1 Board
1-9. PICTURE TUBE REMOVAL
Note:
• For KV-DZ29M30 (South Africa), the picture tube is upside down and the position for the anode cap and tension springs are
change accordingly.
• Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom right
and left.
1) Remove the Rear Cover.
2) Unplug all interconnecting leads from the Deflection Yoke, Neck Assy, Degaussing Coils and CRT grounding strap. Remove
Chassis Assy.
3) Place the TV set with the CRT face down on a cushion (jig).
qf Srew Tapping 7+ Crown Washer (x4)
qa Earth Coating Assy
0 Degaussing Coil
9 Holder, DGC
Removal (x2)
qs Supports, CRT Removal (x2)
qd Spring Tension
Removal (x2)
7 Loosen the Deflection Yoke
fixing screw and remove
4 Anode Cap Removal
8 Band, DGC Removal
6 Loosen the Neck Assembly
fixing screw and remove
Neck Assy & VM coil
5 C Board Removal
– 6 –
KV-DZ29M30/M61/M91
• REMOVAL OF ANODE-CAP
Note:
• After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or
carbon paint on the CRT.
RM-GA002
• REMOVING PROCEDURES
a
a
1 Turn up one side of the rubber cap in the direction
indicated by the arrow a.
b
b
2 Using a thumb pull up the rubber cap firmly in the direction
indicated by the arrow b.
c
Anode Button
3 When one side of the rubber cap is separated from the
anode button, the anode-cap can be removed by turning
up the rubber cap and pulling it up in the direction of the
arrow c.
• HOW TO HANDLE AN ANODE-CAP
1 Do not damage the surface of anode-caps with sharp
shaped objects.
2 Do not press the rubber too hard so as not to damage
the inside of anode-cap.
A metal fitting called the shatter-hook terminal is built
into the rubber.
3 Do not turn the foot of rubber over too hard.
The shatter-hook terminal will stick out or damage the
rubber.
– 7 –
KV-DZ29M30/M61/M91
RM-GA002
H1 Board
D3 Board
SECTION 2
CIRCUIT BOARDS LOCATION
C Board
D Board
B1 Board
A1 Board
VM1 Board
F1 Board
– 8 –
KV-DZ29M30/M61/M91
SECTION 3
ADVANCE OPERATION
3-1. "RESET" FUNCTION
1. Purpose
If a customer faces some setting problem that cannot be solved, using the "RESET" function some items will be
reset to its original setting or factory setting (shipping condition)
2. How to Operate
The following is to show on how to access to the "RESET" Function:User selection = press 'WEGA GATE' t selectt 'SETTING' t go to 'SETUP' page t select 'FACTORY
SETTINGS' t select 'YES'
3. Subsequent of Operation
RM-GA002
Sequential to the resetting operation, TV set would shut down once and automatically turn on again. The power-off
duration is expected to be about 500msec. Initial Setup Menu is displayed.
As a result, some items will be reset to their initial conditions (shipment condition) wheareas some others remain
at the last user selection.
Items that remain at the last user selection
Program No., PICTURE POSITION (included PICTURE
ROTATION and PICTURE V-POSITION), OSD Language, Fine tuning,
TV System, Skip, Program label, Program sorting, Video label,
Picture Adjustment (Picture, Brightness, Color Temperature, VM)
Setting t Custom, Sound Adjustment (100Hz,300Hz,
1KHz, 3KHz, 8KHz) setting t Custom.
Reset Items
Category Default Category Default
Video input RF user last setting
Main Volume 25
Scan mode 100Hz
Picture mode VIVID
Intelligent Picture ON
Sound mode DYNAMIC
Intelligent volume OFF
Surround OFF
Wide mode 4.3
Auto wide ON
*Program Block Reset particular, displayed
channel to unblock
Game mode OFF (Video) *Not available in RF
mode
D-NR OFF
Signal level ON
indicator
* Color System RF = Reset to Auto at the particular/displayed Video
= MI Reset to Auto CH, others keep user setting
Eco mode OFF
Wide mode Wide zoom
4.3 Default Wide zoom
V Center 00
V Size 00
Mute OFF
Initial setup menu Reactivate/ON
Twin size Center
*= Will reset only if watched/displayed during RESET operation
- For Multi model only
– 9 –
KV-DZ29M30/M61/M91
RM-GA002
SECTION 4
SET-UP ADJUSTMENTS
The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :
1. Beam Landing
2. Convergence
3. Focus
The controls and switch should be set as follows unless
otherwise noted:
4. G2(SCREEN)
5. White Balance
Picture Control....................................."NORMAL"
Brightness Control..............................."NORMAL"
Note : Test Equipment Required.
1. Pattern Generator 5. Oscilloscope
2. Degausser 6. Landing Checker
3. DC Power Supply 7. XCV Adjuster
4. Digital Multimeter
......................................................................................................................................................................................................................
Preparation :
• Feed in the white pattern signal.
6. Then move the DY forward and adjust so that the entire
screen becomes green.
• Before starting, degauss the entire screen with the
degausser.
• In order to reduce the geomagnetism on the set's picture
tube, face it east or west.
4-1. BEAM LANDING ADJUSTMENT
1. Input a raster signal with the pattern generator.
2. Loose the deflection yoke(DY) mounting screw, and set
the purity control to the center as shown below:-
Purity control
3. Position Neck Assy as shown below:-
Neck assy
Align the edge of
the neck assy with
the edge of the G2 grid.
G2G1 G3
4. Set the raster signal of the pattern generator to green.
5. Move the DY backward and adjust the purity control so
that green is in the center and blue and red are at the
sides evenly.
7. Now switch over raster signal to red then blue and
confirm the condition.
8. When the position of the DY is determined, tighten it with
the DY mounting screw.
9. If the beam does not land correctly in all the corners of
the screen, use magnet disc to correct it.
Purity control
corrects this area.
b
c
Deflection yoke positioning
corrects these areas.
a
d
a
d
b
Disk magnets or rotatable
disk magnets correct these
areas (a-d).
c
Red
Blue
Green
– 10 –
KV-DZ29M30/M61/M91
RM-GA002
4-2. CONVERGENCE ADJUSTMENT
Preparation:
• Before starting, perform FOCUS adjustment.
• Receive dot/cross hatch pattern.
• Picture Mode "CUSTOM" (PIC 90%, BRT 50%,
COL 50%, HUE 50%, SHP 50%).
a) Vertical Static Convergence
Center dot
R G B
R
G
B
4 pole
magnet
Y magnet
RV9001
4-pole
b) Horizontal Static Convergence
If the blue dots does not converge with the red and green
dots, use the 6 pole magnet to adjust in the manner
described below:-
RG B R G B R GB
RB
G
RG
Magnet
6 Pole
6 Pole Magnet
GB
RB
Purity
C1 Board
1. (Moving vertically), adjust the 4 pole magnet to converge
red, green and blue dots in the center of the screen.
2. Tilt the 4 pole magnet and adjust static convergence to
open or close the 4 pole magnet.
3. When the 4 pole magnet is moved in the direction of
arrow A and B, the red, green and blue dots moves as
shown below:-
A
B B
A
B
G
R
B
B
G
R
Moved RV9001 (H.STAT)
DY pocket
4 Pole Magnet
4 Pole
Magnet
c) Y Separation axis correction magnet adjustment.
1. Receive cross hatch signal.
2. Set Picture to "MINIMUM", Brightness to
"STANDARD".
3. Adjust the Y separation axis correction magnet on the
Neck Assembly so that the horizontal lines at the top
and bottom of the screen are straight.
Red
Red
Blue
Blue Red Blue
Neck assy Neck assy
RGGRB
B
VM1 Board VM1 Board
– 11 –
KV-DZ29M30/M61/M91
RM-GA002
d) Convergence Rough Adjustment
Preparation:
• Before starting this adjustment, adjust the horizontal and
vertical static convergence.
Input cross hatch pattern.
i) TLH
Adjust the horizontal convergence of red and blue dots
by inserting TLH Correction Plate to the DY pocket (left
or right).
ii) YCH
Adjust YCH to balance Y axis.
iii) TLV
Adjust the vertical convergence of red and blue dots.
iv) XCV
Adjust XCV to balance X-axis
B
R
TLH
XCV
RB
YCH
H-TRAP
B
R
ON DY:
TLV
TLV
DY pocket
TLH Plate
R
B
XCV
Fix a Permaloy Assy Correction to the misconverged
b
a
d
Permalloy assembly
c
a to d: Piece B(120), Convergence Correct
or
Permaloy Assy Correction
YCH
e) Screen Corner Convergence
Affix a Piece B(120), Convergence Correct/Permaloy
Assy Correction to the misconverged areas.
ba
a-d : screen-corner
misconvergence
cd
– 12 –
KV-DZ29M30/M61/M91
RM-GA002
4-3. FOCUS ADJUSTMENT
FOCUS adjustment should be completed before White
Balance adjustment.
1. Receive digital monoscope pattern.
2. Set Picture Mode to "STANDARD".
3. Adjust focus VR so that the center of the screen
becomes just focus.
4. Change the receiving signal to white pattern and blue
back.
5. Confirm magenta ring is not noticeable. In case magenta
ring is obvious, then adjust FOCUS VR to balance
magenta ring and FOCUS.
4-5. SUB BRIGHTNESS ADJUSTMENT
1. Set TV to RF Mode.
2. Input PAL monoscope to RF mode.
3. Set the following condition:
i) Receive RF PAL monoscope signal
ii) Set "PICTURE MODE" to "CUSTOM" and adjust
PICTURE to 0% and BRIGHTNESS to 50%.
iii) Adjust Sub BRT (service item COLR 006 SBRT)
to make 10 IRE Slightly glimmer.
iv) Apply the offset steps:
Sub Brightnes Offset
Inch Offset
29" Adjusted + 6 Steps
4-6. WHITE BALANCE ADJUSTMENT
1. Set to Service Mode.
2. Input white raster signal using signal generator to
Video 1.
3. Set picture mode to "VIVID".
4) Adjust White Balance
COLR 000 RDRV
001 GDRV
High Light (100IRE)
}
FLYBACK TRANSFORMER (T6805)
4-4. G2 (SCREEN) ADJUSTMENTS
1. Set the following condition:
- Picture and Brightness to "STANDARD".
- TV to Video mode.
2. Connect R,G,B of the C board cathode to oscilloscope.
3. Adjust Brightness to obtain the cathode value to the
value stated below.
Cathode setting voltage:
170 V ± 2 (VDC)
4. Adjust SCREEN VR [RV9001] on the FBT until the
scanning line disappears.
003 RCUT
004 GCUT
CA100, 100 PLUS: Adjustment Value
X = 0.2444
Y = 0.2466
Color temperature:
45,000°K + 8 MPCD
Cut off (10nit)
}
– 13 –
KV-DZ29M30/M61/M91
RM-GA002
SECTION 5
CIRCUIT ADJUSTMENTS
5-1. ADJUSTMENTS WITH COMMANDER
Service adjustments to this model can be performed using the supplied remote commander RM-GA002.
a. ENTERING SERVICE MODE
With the unit on standby
t [DISPLAY] t 5 t [VOL $+% ] t [POWER]
This operation sequence puts the unit into service mode.
This screen display is:
category in decimal item name in decimal NG command frequency video input name
WHBL 000 WBP 000 x SERVICE 50 S VIDEO 1
item no. service data NVM service field channel no./
release ID version in binary for factory color system (decimal)
CGA20 3.13M 0000 0000 FF FF NTSC3 00100
S_ _ : for SONY
A_ _ : for AIWA
L_ _ : BX1L Full
B_ _ : BX1L Basic
D_ _ : DVD Combo
C_ _ : CX1/CX2
Z_ _ : Sound special
_ _ _01 : Serial no. of the M/P release for each
_ _ _10 ~: use for FY04 BX1
_ _SB : Sub Hercules
software service data reserved power on time
For BP1 Board Version; and BT Version;
Category and release ID will be different.
The rest are the same. (Not use for this model)
destination
BP1 Board Version
category in decimal name in decimal
SUBP 000 IDXH 000
release ID version
CBP00 0.00
BT Version
category in decimal name in decimal
9090 000 UOF 000
release ID version
BT 0A14/M
item no. item service data
software
item no. item service data
software
b. METHOD OF CANCELLATION FROM SERVICE MODE
Set the standby condition (Press [POWER] button on the commander), then press [POWER] button again, hereupon it becomes
TV mode.
c. METHOD OF WRITE INTO MEMORY
1. Set to Service Mode.
2. Press 1 (UP) and 4 (DOWN), to select the adjustment item.
3. Change item by pressing 3, 6.
4. Press [MUTING] button to indicate WRITE on the screen.
5. Press - button to write into memory.
1, 4 Select the adjustment item.
r
3, 6 Raise/lower the data value.
r
[MUTING] Writes.
r
- Executes the writing.
– 14 –
KV-DZ29M30/M61/M91
d. MEMORY WRITE CONFIRMATION METHOD
1. After adjustment, pull out the plug from AC outlet, and then plug into AC outlet again.
2. Turn the power switch ON and set to Service Mode.
3. Call the adjusted items again to confirm adjustments were made.
e. OTHER FUNCTION VIA REMOTE COMMANDER
7, - All the data becomes the values in memory.
8, - All user control goes to the standard state.
Display, - Service data initialization (Be sure not to use usually.)
2, 5 Select Device or Category
5-2. ADJUSTMENT METHOD
Item Number 000 HPOS
This explanation uses H POSITION as an example.
1. Select "000 HPOS" with the 1 and 4 buttons, or 2 and 5.
2. Raise/lower the data with the 3 and 6 buttons.
3. Select the optimum state. (The standard is IF for PAL reception.)
4. Write with the
5. Execute the writing with the - button. (The WRITE display will be changed to red color while executing, and back to
SERVICE.)
Example on screen display :-
button. ( (mute icon))
RM-GA002
GREEN
WHBL 000 WBP 000 SERVICE 50 VIDEO 1
Adjusted with [3] and [6] buttons.
GREEN
WHBL 000 WBP 000 WRITE 50 VIDEO 1
write with .
RED
WHBL 000 WBP 000 WRITE 50 VIDEO 1
Write executed with [0].
The WRITE display
then returns to green
SERVICE
Use the same method for all Items. Use 1 and 4 to select the adjustment item, use 3 and 6 to adjust, write with
execute the write with -.
Note : 1. In [WRITE], the data for all items are written into memory together.
2. For adjustment items that have different standard data between 50Hz or 60Hz, be sure to use the respective input
signal after adjustment.
, then
– 15 –
Adjustment Item Table (Main Micon)
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC )deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD srehtOVUY)VT(LAP)VT(CSTN)VT(MACES)oediV(LAP)oediV(CSTN)oediV(MACESTUPNI-SMACESCSTN
CY000YLDY210510yaleD-Y TUPNI-S/VUY+)OEDIV/VT(*)MACES/CSTN/LAP(cimsoC
0011606001* 6001
100TAMC000300xirtaM)ASU/napaJ(CSTNroMACES-LAP 00
200LCA100100gnitimiLroloCcitamotuA 10
300BC000100ycneuqerFretneCssapdnaBamorhC )xif0:oediV*(VThtiwylnodilav00
400OBS100300tesffOkcalBMACES 10
500ESHC100300ytivitisneStnedICSTN/LAP 30
600OLC000100retliF)lleB(ehcolCfoycneuqerFretneC 00
700PRTC000100edoMparTamorhC srehto/MACES
00
10
800TDQ000100parTamorhCdnoceS srehto/MACES
00
00
900SPB000100eniLyaleDdnab-esaBamorhCfossapyB srehto/CSTN
00
00
010OCF000100nOroloCdecroF 00
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC )deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD
pmeTloC
)rehtoHGIH(
pmeTloC
)rehtoWOL(
pmeTloC
)rehtoMRON(
pmeTloC
)VUYHGIH(
pmeTloC
)VUYWOL(
pmeTloC
)VUYLAMRON(
pmeTloC
)BGRHGIH(
pmeTloC
)BGRWOL(
pmeTloC
)BGRMRON(
0edomciP1edomciP2edomciP
LBHW000PBW000300)woL:3,2,lamroN:1,hgiH:0(gnitteSpmeTroloC edoMerutciPcimsoC
001010
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC)deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD
edomciP
0
edomciP
1
edomciP
2
VToediVlamroN
)3:4(
DHxednI/niwT
paP/
rehtO
JDAS000EUHS700510euH-buS oediV/VT
6060
100FOIP000700)%57(ocE*02/)atad-02(*erutciP(tesffOerutciP REHTO/ITLUM/LAMRON/SMenignEFP
005 7 0
200CIP130721
0[lortnoCerutciP
-
])CSTN(36-0,)ITLUM(001
)ataDteseRresU=lanosreP:AG(ledoMerutciP
0010705
300LOC130721])CSTN(36-0,)ITLUM(001-0[lortnoCroloC )ataDteseRresU=lanosreP:AG(ledoMerutciP
260605
400TRB130721])CSTN(36-0,)ITLUM(001-0[lortnoCssenthgirB )ataDteseRresU=lanosreP:AG(ledoMerutciP
020505
500EUH130721])CSTN(36-0,)ITLUM(001-0[lortnoCeuH )ataDteseRresU=lanosreP:AG(ledoMerutciP
050505
600PHS130721]])CSTN(36-0,)ITLUM(001-0[lortnoCssenprahS )ataDteseRresU=lanosreP:AG(ledoMerutciP
050505
NOTE
a) In the initial value (detailed) colomn, the data after the slash mark ("/") refers to NTSC model data.
No ("/") means data is common for Multi and NTSC model.
b) Item remarked "*", please refer page 27 for the data.
c)
shaded items are no data.
d) Standard data listed on the Adjustment Item Table are reference values, therefore it may be different for each model and for each mode.
e) Note for the Different Data those are the standard data values written on the microprocessor. Therefore, the data values of the models are stored respectively in the memory.
In the case of a device replacement, adjustment by rewriting the data value is necessary for some items.
f) Multi ver3.15.
– 16 –
KV-DZ29M30/M61/M91
RM-GA002
– 17 –
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC)deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD 0506srehtOVUYVToediVtxeteleTpi-VTlangiSoN
CNYS000SYS000100tupnICNYSYnonoitazinorhcnyS cimsoC00
100OF
000300tnatsnoCemiT1esahP
)FR(langisoNrogninuTotuA/txeteleT/oediV/FFOPIVT/NOPIVT
0030100000
200DIV000100edoMtnedIoediV 06/05
0000
300LSF000100cnySlacitreVrofleveLgnicilSdecroF 00
400LSS000100rotarapeScnySleveLgnicilS 06/05
0000
500DIVS100700noitacifitnedIoediVrofnoitceleSecruoS srehtO/VUY
0000
600FROF200300ycneuqerFdleiFdecroF 20
700KVM000100gniyeKnoisiVorcaM 10
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC )deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD
srehtOBGReviLVT
)nyD(
VT
)srehtO(
oediV
)nyD(
oediV
)srehtO(
pmeTroloC
)HGIH(
pmeTroloC
)srehtO(
roloC
)WOL(pmeT
pmeTroloC
)LAMRON(
TCIP000AFC000300edoMretliFbmoC cimsoC00
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC)deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD VUYVToediV
WS0002VC000100noitceleSlangiStupnI2SBVC cimsoC00
100OVS10030084@niPISBVC/OVS/OVFIfonoitcnuFVUY/oediV/VT
201010
200LFD000100noitcetorPhsalF 00
300FTNI000100langisecafretniVUYfoytiraloP/edutilpmA 00
KV-DZ29M30/M61/M91
RM-GA002
KV-DZ29M30/M61/M91
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD
MEDS000SWMF000300rotaludomeDMFrofnoitceleSwodniW cimsoC20
100SSQ100100 )metsysMitlumAGrofA/N(edoMreifilpmA)SSQ(dnuoStilpSisauQ 10
200BPB000100retliFssapdnaBdnuoSfossapyB 00
300OLMA000100dnuoSMAroflangiStuptuOoiduA 00
400CVPH000100lortnoCemuloVenohPdaeH 00
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD
FIV000DFIO630360rotaludomeDFItesffO cimsoC63
100TCGA130360revo-ekaTCGA 72
200MTS000100edoMgninuThcraeS 10
300DG000100langiS1SBVCnoyaleDpuorG 00
400SCGA100300deepSCGAFI 10
500IFF000100LLPFIretliFtsaF 00
600IANL100100eulavlaitinitibANLpmAFR 00
700TANL591552leveLdlohserhTpmAFR 591
800NSNL400700dlohserhTleveLNSpmAFR 40
900DSNL200700dlohserhTporDleveLNSpmAFR 10
010XENL610360gnimiTporDNSkcehcpmAFR 03
110RTHC840721edoMresUpmAFRtesotgrPotuAretfadlohserhTlennahC 52
210RENT0001001-renutGL,0-renutsplA 10
RM-GA002
– 18 –
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC )deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD VTVToediVffOWOW/SRSdnuorrusurToeretsIonomIsrehtO
PSDS000LBB000510ruotnoCEBB dnuoS
PSD
4020
100HBB000510ssecorPEBB 4101
200WLBB000510tesffOruotnoCEBB
4040
300FOVS000510tesffOemuloVedoMtceffE/dnuorruS onomI/oeretsI/dnuorrusurT/)WOW/SRS(ffO
4090406040
400DAL000130tsujdAleveLredoceD 40
500MAL000130tsujdAleveLonoM 40
600NAL000130tsujdAleveLmaciN 22
700SAL000130tsujdAleveLPAS 80
800AAL000130tsujdAleveLCDA oediV/Lnon-VT/L-VTI)oruEnoN(oediV/vT
7100
900FES300700tceffEoeretS/onoMelbidercnI onomI/oeretsI
5030
010SAB000510tesffOssaBniaM
0202
110ERT000510tesffOelberTniaM
5272
2101QE000510tesffO)zH001(dnaBlennahCniaMrezilauqE 0000
3102QE000510tesffO)zH003(dnaBlennahCniaMrezilauqE 8181
4103QE000510tesffO)zH0001(dnaBlennahCniaMrezilauqE
0010
5104QE000510tesffO)zH0003(dnaBlennahCniaMrezilauqE
5060
6105QE000510tesffO)zH0008(dnaBlennahCniaMrezilauqE 1020
710TCFB500700lortnoCEBBdnaBUD,EBD 50
810NECS100510lortnoCretneCD3SRS 40
910APSS000510lortnoCecapSD3SRS 10
020WHBB000510edomWOWnitesffossecorpEBB
0000
120ERTS200700edomdnuorrusroftesffOelberT 10
220THBB000510edomVTnitesffOEBB 00
320ERTT200700edoMVTnitesffOelberT 30
4201QEC800510)zH001(ataDdnaBrezilauqEnI-retneC 60
5202QEC800510)zH003(ataDdnaBrezilauqEnI-retneC 90
6203QEC800510)zH0001(ataDdnaBrezilauqEnI-retneC 01
7204QEC800510)zH0003(ataDdnaBrezilauqEnI-retneC 01
8205QEC800510)zH0008(ataDdnaBrezilauqEnI-retneC 70
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD
TXT000VXT930360spilihProfnoitisoPlacitreVtxeteleT ossaciP93
100DHT010721tfihSegdEevitcAcnys-HtxeteleT 11
200RBT820130)edomllufrof(ssenthgirBBGRtxeteleT 61
300MRBT310130)edomXIMrof(ssenthgirBBGRtxeteleT 81
400DTSN000100)edomXIMotog:1,TXTlecnac:0(langiSdradnatSnoNfoM/C 00
500QCA000100)1-LAP,0-otuA(noitisiuqcAtxeteleT 00
(only for model with teletext function)
– 19 –
KV-DZ29M30/M61/M91
RM-GA002
– 20 –
JVTytilanoitcnuF.tinIegnaRnoitcnuF etoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD
CEDS000UTPS300510noitcetedreirracPASrofdlohserhTreppU dnuoS
PSD
80
100LTPS600510noitcetedreirracPASrofdlohserhTrewoL 51
200HTPS000130PASfoetumotuarofdlohserhTesioN 00
300YHPS400510PASfoetumotuarofezissiseretsyH 30
400HTMF000130dradnats2AMFni2CSfoetumotuarofdlohserhTesioN 81
500YHMF400510dradnats2AMFni2CSfoetumotuarofezissiseretsyH 70
600ELIN001552)PEDD(timilrorrerewolMACIN 05
700EUIN002552)PEDD(timilrorrereppuMACIN 002
800DMPE100300)PEDD(gnimmargorPysaECEDMED
1=1tiB3POdna0=SDTSdna0=DMPEfI
revoekatlliwyrogetacCKDSdnaelbasiDsiyrogetacCEDS
*
900SDTS910130sedomSSSdnaDSArofdexelpitlumstiB *
010AMVO100100noitpadanoitaludomrevoMF 00
110WBLF000300htdiwdnabretlifrotaludomedMA/MF 30
210DMDI000300edomSSSnideepstnediMF 00
310TMVO100200lanimonotevitalerdlohserhtlevelnoitaludomrevO 30
410IXCD000100retrevnIlortnoCgnilacSOXCDMACIN *
510GXCD000700niaGlortnoCgnilacSOXCDMACIN *
610LLCD110510)L(timiLlortnoCgnilacSOXCDMACIN 00
710HLCD000130)H(timiLlortnoCgnilacSOXCDMACIN *
810RKDI100300DTSMnaeroKrofgnittesDOMDI 00
JVTytilanoitcnuF.tinIegnaRnoitcnuF etoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD
CKDS000LLNK000552etyBrewoLdlohserhTrewoLteDesioNnaeroK
1=1tiB3POdna0=SDTSdna0=DMPEfI
revoekatlliwyrogetacCKDSdnaelbasiDsiyrogetacCEDS
100HLNK210552etyBrehgiHdlohserhTrewoLteDesioNnaeroK
200LHNK000552etyBrewoLdlohserhTreppUteDesioNnaeroK
300HHNK020552etyBrehgiHdlohserhTreppUteDesioNnaeroK
400CILK060552tnuocgniniatniamDItoliPtsoLnaeroK
500MILK100721reilpitlumtnuocgniniatniamDItoliPtsoLnaeroK
600CDSK600552tnuoCtceteDoeretSnaeroK
(only applicable for Korea model)
KV-DZ29M30/M61/M91
RM-GA002
JVTytilanoitcnuF
.tinIegnaRnoitcnuFetoN&elbaTeciveD
emaN
nommoC )deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD
0RN
)0elbaT(
1RN
)1elbaT(
2RN
)2elbaT(
3RN
)3elbaT(
4RN
)4elbaT(
0CSTN
)5elbaT(
1CSTN
)6elbaT(
1RN-FR
)1elbaT(
-FR
1CSTN
)6elbaT(
-VT
LAP
-VT
CSTN
OEDIV
LAP-
-OEDIV
CSTN
RN3
000TED3000700TEDD3
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
bmoCD3
707070707070707070
100ROC3000100RROCRND3
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
100000000010000010
200CFA000300NIAGCFA
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
303030303030303030
300GEH000300NIAGAHNEH 00
400RNC2000510MILRNCD2&KRNC-D2
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
003050509020003000
500CNY000700MILCN-Y;RELLECNACESIONY
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
003030507020103030
600RNY2000510NIAGRNYD2;KRNYD2
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
000020008010102000
700LNY2000300MILRNYD2
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
002030003020203030
800KLB000300PXEKLB 10
900RNC3000700MILRNCD3
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
000030307000000000
010KNC3000300KRNCD3
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
000000000000000000
110GNC3000700NIAGRNCD3
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
002020207000004000
210RNY3000700MILRNYD3
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
003030606000001000
310KNY3000300KRNYD3
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
001020000000001030
410GNY3000700NIAGRNYD3
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
002050606000001000
510YLDY000821YALEDTUPTUOY
/LAP-DIV/CSTN-VT/LAP-VT
CSTN-S/LAP-S/CSTN-DIV
30706040
610ACI000100OTUAPMALCTNI 10
710MCI000100LAUNAMPMALCTNI 00
810HNEC000100AHNEC 10
910KCI000100YEKPMALCTUPNI 10
020KGB000100YEKETAGTSRUB 10
120LSS000100FPLPESCNYS 00
– 21 –
KV-DZ29M30/M61/M91
RM-GA002
KV-DZ29M30/M61/M91
JVTytilanoitcnuF
.tinIegnaRnoitcnuFetoN&elbaTeciveD
emaN
nommoC )deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD
0RN
)0elbaT(
1RN
)1elbaT(
2RN
)2elbaT(
3RN
)3elbaT(
4RN
)4elbaT(
0CSTN
)5elbaT(
1CSTN
)6elbaT(
1RN-FR
)1elbaT(
-FR
1CSTN
)6elbaT(
-VT
LAP
-VT
CSTN
OEDIV
LAP-
-OEDIV
CSTN
-S
LAP
-S
CSTN
lamroN
)3:4(
DHxednI/niwT
paP/
rehtO
RN3
220RCEV000300EROCAHNEV
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
bmoCD3
001010300000101010
320GEV000300NIAGAHNEV
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
000010100000100010
420NEV000300LNAHNEV
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
000010100000100010
5201PMA0007001PMADH
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
606060606060606060
620VGDH000130VNIAGDH
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
818181818181818181
7202PMA0007002PMADH
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
606060606060606060
8201GDH0001301NIAGDH
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
313131313131313131
9203PMA0007003PMADH
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
505050505050105050
0302GDH0001302NIAGDH
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
404040404040104040
130PLSC000510PLSSCA&PLSMCA
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
514101015101010101
230PLSY000510PLSSYA&PLSMYA
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
515101400141414141
330SMCA000510TESFMCA&TESEMCA
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
510101015151510151
430SSCA000510TESFSCA&TESESCA
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
510101015151010101
530SMYA000510TESFMYA&TESEMYA
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
511101015151511151
630SSYA000510TESFSYA&TESESYA
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
511141015111014101
730LSCB000510PLSSCB&PLSMCB
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
51
0101015141510151
830LSYB000510PLSSYBPLSMYB
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
510101015141310121
930SMCB000510TESFMCB&TESEMCB
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
510101015151010101
040SSCB000510TESFSCB&TESESCB
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
510101015151010101
140SMYB000510TESFMYBTESEMYB
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
515101015151515151
240SSYB000510TESFSYBTESESYB
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
515101015151015101
340MCEC000700PMCEC
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
704070704040407040
440MCSC000510PMCSC
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
510151510000005100
540VH1F000510REV1F&REH1F
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
508050505050508050
640FERM000510FERM
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
207040404010607060
740YEDC000300EYEDC
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
203020202020003000
840YEDY000300EYEDY
/1tN/0TN/3RN/2RN/1RN/0RN
1CSTN-FR/1RN-FR
203020202020003000
940SAMH000700TUOKSAM-H
00
050SAMV000130TUOKSAM-V
00
RM-GA002
– 22 –
GVTytilanoitcnuF
laitinIegnaRnoitcnuFetoN&elbaTeciveD
emaN
nommoC
)deliateD(eulaVlaitinI
yrogetaCoNemaNceDceD
ciP
0edom
ciP
1edom
ciP
2edom
FRtpecxE
0edomciP
FRtpecxE
1edomciP
FRtpecxE
2edomciP
ITL000SFC100100noitceleSretliFruotnoC 10
100CDV100100gniroCtnednepeDoediVedoMerutciP
101010
200MED000100edoMnoitartsnomeD 00
300PDC400700yaleDecnanimuL 40
400KSD000100hctiwSenoTnikSedoMerutciP
000000
500KSA000100noitceleSelgnAenoTnikS 00
600KSW000100noitceleShtdiWenoTnikS 00
700KSS000100noitceleSeziSenoTnikS 00
800RGD100100hctiwStnemecnahnEneerGedoMerutciP
101000
900TGD700700hctiwStnemecnahnEneerGfodlohserhT 70
010RGG000100niaGtnemecnahnEneerG 00
110RGW000100htdiWtnemecnahnEneerG 00
210RGS000100eziStnemecnahnEneerG 00
310SDC100100ssenprahStnednepeDroloCedoMerutciP
101000
410TSC700700ssenprahStnednepeDroloCfodlohserhT 70
510ITC100100tnemevorpmItneisnarTroloCedoMerutciP
101000
610NOB000100noitasnepmoCtesffOkcalBedoMerutciP
000000
710DTB000360htcertSkcalBevitpadAedoMerutciP
000000
810DLN120360reifilpmAytiraeniL-noNedoMerutciP
121200
910WLN700700reifilpmAytiraeniL-noNfohtdiWpetS 70
020DGV130360ammaGelbairaVedoMerutciP
137272
120WGV000700ammaGelbairaVfohtdiWpetS 00
220DKP040360edutilpmAgnikaeP)srehtO/VT(*edoMerutciP
040341550402
320WKP800510edutilpmAgnikaePfohtdiWpetS 80
320DPS000360noitcerroCssenpeetSedoMerutciP
000000
520DRC050360leveLgniroC)srehtO/VT(*edoMerutciP
050300038100
620WRC900510leveLgniroCfohtdiWpetS 90
720ORC600510edoMoediVroftesffOleveLgniroC 60
820DWL130360noitcerroChtdiWeniL 13
920ITLE100100
ITLelbasiD/elbanE
]noitpo1XC-tsoP[lortnoc
10
– 23 –
KV-DZ29M30/M61/M91
RM-GA002
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC)deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD 0506
PBUS000HXDI500510noitisoplatnozirohDSOxednIataDtimsnarTossaciPbuSossaciPbuS50
100VXDI740360noitisoplacitrevDSOxednI)06/05(ataDtimsnarTossaciPbuS7474
200BXDI130130ssenthgirbDSOxednIataDtimsnarTossaciPbuS13
(only applicable for 2 tuners models)
– 24 –
KV-DZ29M30/M61/M91
RM-GA002
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC)deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD 0506VUYVToediVlangiSoN
SOCS000SYS100100tupnICNYSYnonoitazinorcnyS cimsoCbuS00
100OF000300tnatsnoCemiT1esahP )FR(langisoNrogninuTotuA/VT
003000
200DIV100100edoMtnedIoediV 06/05
0000
300LSF000100cnySlacitreVrofleveLgnicilSdecroF 00
400LSS000100rotarapeScnySleveLgnicilS 06/05
0000
500DIVS000700noitacifitnedIoediVrofnoitceleSecruoS VUY/oediV/VT
000000
600FROF300300ycneuqerFdleiFdecroF 20
700OVS00030084@niPISBVC/OVS/OVFIfonoitcnuF VUY/oediV/VT
000000
800EXDV
000100dnareifilpmaFInoisivneewtebgnilpuocfolortnoC
tiucricnoitasinorhcnys
00
900XDV
000100dnareifilpmaFInoisivneewtebgnilpuoC
tiucricnoitasinorhcnys
00
010YLDY210510tnemtsujdayaled-Y 00
110DFIO630360rotaludomeDFItesffO 63
210TCGA130360revo-ekaTCGA 13
310MTS100100edoMgninuThcraeS 00
410DG000100langiS1SBVCnoyaleDpuorG 00
510SCGA100300deepSCGAFI 00
610IFF000100LLPFIretliFtsaF 00
710SSMC000100tiucrictnedioedivehtroflangistupnicnysfonoitceleS 00
810PMAO300300edutilpmAlangiStuptuOoediV 30
910IAV000100noitcerroCedutilpmAlangiStuptuOImetsyS 00
020SWMF200300rotaludomeDMFrofnoitceleSwodniW 20
120SSQ
000100edoMreifilpmA)SSQ(dnuoStilpSisauQ
)ledoMAGtpecxe(
00
220BPB000100retliFssapdnaBdnuoSfossapyB 00
3202BPB0001002retliFssapdnaBdnuoSfossapyB 00
420TPS000100edomkcirtecnamrofrepcnyS 00
520D2E000100nipMEEDUAnolangistuptuooiduafonoitceleS 00
620CVPH000100lortnoCemuloVenohPdaeH 00
720GSD000100stuptuooiduaotstupnioiduamorfniaG 00
820DSV100100elbasidnacslacitreV 00
920ESHC100300ytivitisneStnedICSTN/LAP 20
– 25 –
(only applicable for 2 tuners models)
KV-DZ29M30/M61/M91
RM-GA002
– 26 –
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD
VTH000XAMV000360)XAMV+53=XAM(leveLemuloVmumixaM leveLemuloV00
100INIV520130norewoptaleveLemuloVlaitinI leveLemuloV52
200YBTS000100 )YBTSsyawla=1,sutatsrewoptsalehtwollof=0(sutatSrewoPtsaL rewoPtsaL00
300GRPI100721)sledomitluMrofylno(norewoptarebmuNmargorPlaitinI
ot0:lageL(rebmuNmargorP
)1otteserlliw,001>fi,99
10
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD
MTPO000THSA600700)nim5*atad(remitffotuhsotuA 00
100ETUM000100)delbane=1(hctiwSetuMlangiSoN 00
200LUFR510510)hf0nehwelbasiD(dekcolnUretfaretnuoCegnahClangiSFR 40
300KLFR510510)hf0nehwelbasiD(dekcoLretfaretnuoCegnahClangiSFR 00
400GNAL000300noitidnocgnippihsegaugnalDSO 00
500TXTH000100wsrotarapescnyS cimsoC00
600SSMC000100wscnyS cimsoC10
700OXCD060592eulaVOXCD ossaciP*
800CSID821552cedrolocybtsujdaOXCDrofatadOCSIDtegraT 431
900LBXE000510esioNetihWetanimilEotremiTgniknalBdednetxE 01
010SYST000300 )ledoMAG(]M:3,K/D:2,I:1,G/B:0[teseRtseTtaMVNnisySVTeziromeM 00
110LBL100100noitidnoclangiSoNtAnoitcudeRssenthgirB 00
210P32100100otuA:1,FFOecroF:0edoMnwoDlluP3/2 enignEFP10
310WSNL100100)ffO:0,otuA:1(noitidnocteseRtseT/gnippihSretsooBlangiS 10
410MTSD000100)elbasid:1,elbane:0(ybdnatSniedompotselbasiD 10
510MPSC000100)elbasid:1,elbane:0(yromeMtsaLrekaepSretneCelbanE 00
610WSRN100200)HGIH-2,woL-1,FFO-0(noitidnoCgnippihSretfagnitteSRN 10
KV-DZ29M30/M61/M91
RM-GA002
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC)deliateD(eulaVlaitinI
yrogetaC.oNemaNceDceD srehtOVUY
SUPO000FFOS000100)noCAhtiwybdnats:1,noCAhtiwyromemtsalwollof:0(ffoyatS
100RBCC510130ssenthgirBDSOCC
200HCPS100721noitidnoCgnippihSretfarebmuNlennahC
300ACPS100100)nOelbaC=1(noitidnoCgnippihSretfanoitceleSelbaC
400VUO000100)SUrofylno(slangiStupnIVUnolortnoCtesffO VUY/srehtOcimsoC
5002AFC000100)SUrofylno(nOretliFbmoCdecroF enoncimsoC
(only applicable for NTSC models)
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoCsrehtOMACESCSTN
yrogetaC.oNemaNceDceD
PVPO000SBPB000100)SBPB(edomoeretstaretlifssapdnabdnuosfossapyB cimsoC10
100CYWB000100)CYMB(metsysroloczHM85.3rofedomCYtahtdiwdnaB 00
200BSO000100)BSO(rotaludomedamorhcfoeslupyektsrublanretnifohtdiW 00
300VUYT000100)VUYTXT(noitcelestuptuoCC/TXT 10
400DCL000100)DCL(edoMDCL 10
500CKB000100noitisoPyeKtsruB )LAP(SREHTO/MACES/CSTN
001000
JVTytilanoitcnuF.tinIegnaRnoitcnuFetoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD
BTPO000LLAI000100)MVNnideziromemton(hctiwSetirWdradnatS X
1001BPO000552)detalerlangiSoediV(1noitpO
tibnoitporoF(
otreferatad
)03~92segap
2002BPO000552)detalergnidoceDoeretS(2noitpO
3003BPO000552)suoenallecsiM(3noitpO
4004BPO000552)suoenallecsiM(4noitpO
5005BPO000552)detaleregnaugnaLDSO(5noitpO 13egaprefer
– 27 –
KV-DZ29M30/M61/M91
RM-GA002
KV-DZ29M30/M61/M91
RM-GA002
Data Variant depend on models
Category No Name Stereo AV Stereo
SDEC 008 EPMD 02 01
009 STDS 31 13
014 DCXI 00 00
015 DCXG 03 00
017 DCLH 06 00
Category No Name Stereo AV Stereo
OPTM 007 DCXO 53 48
– 28 –
KV-DZ29M30/M61/M91
RM-GA002
ITEM INFORMATION
No. OPB1
Item WSS RF HD Front Component NR Composite SECAM Color Decoding DEC
KV-DZ29M30 0011010052
KV-DZ29M61 0011010052
(Malaysia)
KV-DZ29M61(GE) 0011010052
KV-DZ29M91 0011010052
WSS RF (Wide Screen Signaling in RF mode) 0 = disabled, 1 = enabled
HD Front (HD at front input) 0 = disabled, 1 = enabled
Component (Component [YCbCr] Terminals) 0 = 1 Component terminal
1 = 2 Component terminals
Composite (No. of Composite Terminals) 0 = 3 Composite terminals
1 = 4 Composite terminals
NR (Noise Reduction) 0 = NR disabled,
1 = enabled (Note: 3D Comb must be off when
NR is set to ON
SECAM (SECAM Color System) 0 = disabled,
1 = enabled (valid only if Color Decording
= 00 or 10)
Color decording (Color Crystal Selection) 00 = PAL/NTSC/SECAM (Multi)
01 = NTSC (3.58MHz)/SECAM
10 = PAL/NTSC/SECAM (4.43MHz)
11 = Reserved (Tri-Norma)
No. OPB2
Item REV NICAM REV A2 Thai Bilingual/ US ST Korean REV DEC
Force SAP ST
KV-DZ29M30 0101000080
KV-DZ29M61 0101000080
(Malaysia)
KV-DZ29M61(GE) 0101000080
KV-DZ29M91 0101000080
NICAM (NICAM Stereo) 0 = disabled, 1 = enabled
A2 (A2 [West German] Stereo/Bilingual) 0 = disabled, 1 = enabled
Thai Bilingual (A2 [Thai] Bilingual) 0 = disabled, 1 = enabled
Forced SAP (Force SAP mode only if US
ST is active) 0 = disabled, 1 = enabled
US ST (US Stereo) 0 = disabled, 1 = enabled
Korean ST (Korean Stereo) 0 = disabled, 1 = enabled
– 29 –
Loading...