Sony KV-AR21M30, KV-AR21M61, KV-AR21M81, KV-AR21M90 Service Manual

REVISION HISTORY

BX1S
CHASSIS
MODEL
KV-AR21M30 KV-AR21M61 KV-AR21M61 KV-AR21M61 KV-AR21M81
KV-AR21M90
NO. SUFFIX DATE SUPPL. / CORR DESCRIPTION
PART NO.: 9-872-364-03
2 -02 2004/4 Supp-1 Service Data Version Change (Page 70)
3 -03 2004/7 Corr-1 IC001 Part Number Change (Page 67)
SERVICE MANUAL
BX1S
CHASSIS
MODEL COMMANDER DEST. CHASSIS NO.
KV-AR21M30 RM-W101 Oceania SCC-V03A-A KV-AR21M61 RM-W100 GE SCC-V04D-A KV-AR21M61 RM-W100 Malaysia SCC-U96B-A KV-AR21M61 RM-W100 Thailand SCC-U94D-A KV-AR21M81 RM-W100 ME SCC-U90B-A KV-AR21M90 RM-W101 Hong Kong SCC-U97F-A
MODEL COMMANDER DEST. CHASSIS NO.
TRINITRON
®
RM-W101RM-W100
COLOR TV
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
(KV-AR21M61/KV-AR21M81)
Power requirements 110-240 V AC, 50/60 Hz KV-AR21M61(GE)/AR21M81
220-240 V AC, 50/60 Hz Malaysia and Thailand
Power consumption (W) Indicated on the rear of the TV
Television system B/G, I, D/K, M
Color system PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43
Stereo/Bilingual system NICAM Stereo / Bilingual B/G, I Except Thailand
A2 Stereo / Bilingual B/G
NICAM Stereo / Bilingual B/G, I, D/K; Thailand only A2 Stereo / Bilingual B/G
Teletext language English, French KV-AR21M61
English, Farsi (Persian) KV-AR21M81
Channel coverage
B/G VHF: E2 to E12 / UHF: E21 to E69
CATV: S01 to S03, S1 to S41
I UHF: B21 to B68
CATV: S01 to S03, S1 to S41
D/K VHF: C1 to C12, R1 to R12
UHF: C13 to C57, R21 to R60 CATV: S01 to S03, S1 to S41, Z1 to Z39
M VHF: A2 to A13
UHF: A14 to A79 CATV: A-8 to A-2, A to W+4, W+6 to W+84
8 (Antenna) 75-ohm external terminal
Audio output (Speaker) 10W + 10W
Number of terminal
D Video Input: 2 Output: 1 Phono jacks; 1 VP-P, 75 ohms 9 Audio Input: 2 Output: 1 Phono jacks; 500 mVrms
(S Video) Input: 1 Y: 1 Vp-p, 75 ohms, Except Thailand
(Component Input: 1 Phono jacks;
Video) Y: 1 Vp-p, 75 ohms,
2 (Headphone) Output: 1 Stereo minijack
Picture tube 21 in.
Tube size (cm) 54 Measured diagonally
Screen size (cm) 51 Measured diagonally
Dimension (w/h/d, mm) 589 x 463 x 479
Mass (kg) 27
SPECIFICATIONS
unbalanced, sync negative C: 0.286 Vp-p, 75 ohms
sync negative
B: 0.7 Vp-p, 75 ohms
C
R: 0.7 Vp-p, 75 ohms
C Audio: 500 mVrms
Note
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
– 2 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
SPECIFICATIONS
(KV-AR21M30/KV-AR21M90)
Power requirements 220-240 V AC, 50/60 Hz
Power consumption (W) Indicated on the rear of the TV
Television system B/G, I, D/K, M
Color system PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43
Stereo/Bilingual system NICAM Stereo / Bilingual B/G, I; A2 Stereo / Bilingual B/G
Channel coverage
B/G VHF: E2 to E12
UHF: E21 to E69 CATV: S01 to S03, S1 to S41
I UHF: B21 to B68
CATV: S01 to S03, S1 to S41
D/K VHF: C1 to C12, R1 to R12
UHF: C13 to C57, R21 to R60 CATV: S01 to S03, S1 to S41, Z1 to Z39
M VHF: A2 to A13
UHF: A14 to A79 CATV: A-8 to A-2, A to W+4, W+6 to W+84
8 (Antenna) 75-ohm external terminal
Audio output (Speaker) 10W + 10W
Number of terminal
D Video Input: 2 Output: 1 Phono jacks; 1 VP-P, 75 ohms 9 Audio Input: 2 Output: 1 Phono jacks; 500 mVrms
(S Video) Input: 1 Y: 1 Vp-p, 75 ohms,
unbalanced, sync negative C: 0.286 VP-P, 75 ohms
(Component Input: 1 Phono jacks;
Video) Y: 1 Vp-p, 75 ohms,
sync negative
B: 0.7 Vp-p, 75 ohms
C
R: 0.7 Vp-p, 75 ohms
C Audio: 500mVrms
2 (Headphone) Output: 1 Stereo minijack
Picture tube 21 in.
Tube size (cm) 54 Measured diagonally
Screen size (cm) 51 Measured diagonally
Dimension (w/h/d, mm) 589 x 463 x 479
Mass (kg) 27
Note
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CARBON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
– 3 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100

TABLE OF CONTENTS

Section Title Page
SELF DIAGNOSTIC FUNCTION.............................. 5
1. DISASSEMBLY
1-1. Rear Cover Removal ................................................. 8
1-2. Speaker Block Assy Removal................................... 8
1-3. Chassis Assy Removal .............................................. 8
1-4. Service Position ........................................................ 8
1-5. Terminal Bracket Removal ....................................... 8
1-6. A Board Removal ...................................................... 8
1-7. Picture Tube Removal ............................................... 9
2. SET-UP ADJUSTMENTS
2-1. Beam Landing ......................................................... 10
2-2. Convergence ............................................................ 11
2-3. Focus Adjustment .................................................... 13
2-4. G2 (SCREEN) Adjustments ................................... 13
2-5. White Balance Adjustment ..................................... 13
2-6. Sub Bright Adjustment ........................................... 13
3. CIRCUIT ADJUSTMENTS
3-1. Adjustment With Commander ................................ 14
3-2. Adjustment Method ................................................ 15
3-3. Picture Quality Adjustment .................................... 30
3-4. Deflection Adjustment ............................................ 30
3-5. Drive Adjustment .................................................... 31
3-6. Picture Distortion Adjustment ................................ 32
Section Title Page
4. DIAGRAMS
4-1. Block Diagram ........................................................ 33
4-2. Circuit Boards Location .......................................... 34
4-3. Schematic Diagram Information ............................ 34
4-3-1. CV Board Schematic Diagram .................... 35
4-3-2. A Board — Processer (Block A) .................. 36
4-3-3. A Board — Audio (Block B) ....................... 38
4-3-4. A Board — Power Supply (Block C) .......... 40
4-3-5. A Board — Deflection (Block D)................ 42
4-3-6. A Board — Tuner (Block E) ........................ 44
4-3-7. A Board — Jack (Block F) .......................... 46
4-4. Voltage Measurement and Waveforms ................... 49
4-5. Printed Wiring Boards and Parts Location ............. 53
4-6. Semiconductors ....................................................... 56
5. EXPLODED VIEWS
5-1. Chassis ..................................................................... 58
6. ELECTRICAL PARTS LIST .................................... 60
INSTRUCTION MANUAL
– 4 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100

SELF DIAGNOSTIC FUNCTION

The units in this manual contain a self diagnostic function. If an error occurs, the STANDBY (1) indicator will automatically begin to flash. A description of the self-diagnosis function is explained in the instruction manual. The number of times the STANDBY (1) indicator flashes translates to a probable source of the problem. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICATORS
When an errors occurs, the STANDBY (1) indicator will flash a set number of times to indicate the possible cause of the problem. If there is more than one error, the indicator will identify the first of the problem areas.
Result for all of the following diagnosis items are displayed on screen. No error has occured if the screen displays a "0".
Diagnosis
Item
Description
Power does not turn on
+B overcurrent (OCP)*
V-Protect
IK (AKB)
Power supply NG (+5V) for Video Processor
* If a +B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously. The symptom that is
diagnosed first by the mirco controller is displayed on the screen.
** Refer to Screen (G2) Adjustment in this manual.
No. of timer
STANDBY (1)
indicator flashes
Does not light
2 times
4 times
5 times
8 times
Self-Diagnostic
display/
Diagnosis result
2:0
or
2:1 ~ 255
4:0
or
4:1 ~ 255
5:0
or
5:1 ~ 255
8:0
or
8:1 ~ 255
Probable Cause
Location
• Power cord is not plugged in.
• Fuse is burned out (F600) A board.
• H OUT (Q805) is shorted. (A board) IC751 is shorted. (CV board)
• +13V is not supplied. (A board)
• IC804 is faulty. (A board)
• Video OUT (IC1545) is faulty. (A board)
• IC001 is faulty. (A board)
• Screen (G2) is improperly adjusted.**
• IC604 faulty.
• IC602 faulty.
Detected
Symptoms
• Power does not turn on.
• No power is supplied on TV.
• AC Power supply is faulty.
• Power does not come on.
• Load on power line is shorted.
• Has entered standby state after horizontal raster.
• Vertical deflection pulse is stopped.
• Power line is shorted or power supply is shorted.
• No raster is generated.
• CRT Cathode current detection reference pulse output is small.
• No power supply to CRT ANODE.
• No RASTER is generated.
– 5 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
2. DISPLAY OF STANDBY (1) INDICATOR
FLASH COUNT
Diagnostic Item Flash Count*
+B overcurrent 2 times V-Protect 4 times IK (AKB) 5 times Power Supply NG (+5V) 8 times for Video processor
Lamp ON 300ms
Lamp OFF 300ms
Lamp OFF 3 sec
* One flash count is not used for self-diagnosis.
STANDBY (1) indicator
3. STOPPING THE
STANDBY (1) INDICATOR FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY (1) indicator from flashing.
4. SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as "power sometimes shuts off" or "screen sometimes goes off" that cannot be confirmed, it is possible to bring up past occurrences of failure on the screen for confirmation.
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
Display
/ Channel 5 / Volume / Power / TV
˘
Note that this differs from entering the service mode (volume [+]).
The following screen will be displayed indicating the error count.
SELF DIAGNOSTIC
2 : 0 3 : N/A 4 : 0 5 : 1 8 : 0
101 : N/A
Numeral "0" means that no fault was detected. Numeral "1" means the number of a fault occurrence (1 ~ 255).
– 6 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to "0".
Unless the result display is cleared to "0", the self-diagnosis function will not be able to detect subsequent faults after completion of the repairs.
[Clearing the result display]
To clear the result display to "0", press buttons on the remote commander subsequent as shown below when the self-diagnostic screen is being displayed.
8 , -
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
6. SELF-DIAGNOSTIC CIRCUIT
FROM
CV BOARD
IC751 PIN 5
A BOARD
FROM
Q804
COLLECTOR
A BOARD
IC001
Y/CHROMA JUNGLE
IK
32
EHTO
A BOARD
IC804
V.OUT
F.B-PLS
A BOARD
IC001
SYSTEM
SDA1
3 1384
V.GUARD
RED LED
99
122
DISPLAY
A BOARD
IC003
MEMORY
5
SDA
[+B overcurrent $OCP%] Occurs when an overcurrent on the +B(135V) line is detected by pin 32 of IC001 (A board).
If the voltage of pin 32 of IC001 (A board) is more than 4V, the unit will automatically go to standby.
[V-PROTECT] Occurs when an absence of the vertical deflection pulse is detected by pin 13 of IC001
(A board).
[IK $AKB%] If the RGB levels* do not balance within 15 sec after the power is turned on, this error will
be detected by IC001 (A board). TV will stay on, but there will be 5 times LED blinking.
POWER SUPPLY NG (+5V) for VIDEO PROCESSOR
Occurs when IC001 internal HV protect detects an abnormal H-Pulse (frequency) due to improper power supply to IC001. TV cuts off high voltage power of anode CRT. No picture will be detected. eg: IC602, IC604 go faulty.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
– 7 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
SECTION 1

DISASSEMBLY

1-1. REAR COVER REMOVAL
2 Rear cover
1 Eight screws
(BVTP 4 × 16)
1-2. SPEAKER BLOCK ASSY REMOVAL
2 Speaker Block assy
1-3. CHASSIS ASSY REMOVAL 1-4. SERVICE POSITION
2 Four screws
(BVTP 4x16)
1-5. TERMINAL BRACKET REMOVAL 1-6. A BOARD REMOVAL
1 One screws (+BVTP 3 × 12)
2 Bracket FBT
4 Terminal bracket
3 One screws
(+BVTP 4 × 16)
A Board
– 8 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
1-7. PICTURE TUBE REMOVAL
Note:
The picture tube is upside-down for KV-AR21M30 (OCE) only and the position for the anode cap and tension springs are changed accordingly.
Please make sure the TV set is not in standing position before removing necessary CRT support located on bottom right and left.
1) Place the TV set with the CRT face down on a cushion jig.
2) Remove the rear cover.
3) Remove the Speaker Block Assy.
Nut, Special, CRT (x4)
qs Earth Coating Assy
9 Holder, DGC Removal (x2)
qa Spring Tension Removal
8 Support, CRT Removal (x2)
6 Loosen the Deflection Yoke
fixing screw and remove
4 Anode Cap Removal
0 Degaussing Coil
5 CV Board Removal
7 Chassis Assy Removal
• REMOVAL OF ANODE-CAP
Note:
After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the CRT.
REMOVING PROCEDURES
c
a
a
1 Turn up one side of the rubber cap in the direction
indicated by the arrow A.
b
b
2 Using a thumb pull up the rubber cap firmly in the di-
rection indicated by the arrow B.
3 When one side of the rubber cap is separated from
the anode button, the anode-cap can be removed by
anode button
turning up the rubber cap and pulling it up in the direction of the arrow C.
HOW TO HANDLE AN ANODE-CAP
1 Do not damage the surface of anode-caps with
sharp shaped objects.
2 Do not press the rubber too hard so as not to
damage the inside of anode-cap. A metal fitting called the shatter-hook terminal is built into the rubber.
3 Do not turn the foot of rubber over too hard.
The shatter-hook terminal will stick out or damage the rubber.
9
KV-AR21M30/AR21M90/AR21M61/AR21M81
Purity control
RM-W101 RM-W100

SET-UP ADJUSTMENTS

SECTION 2
The following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in the following order :
1. Beam Landing
2. Convergence
3. Focus Set the controls as follows unless otherwise noted:
VIDEO model ..................................................... Standard
PICTURE control .................................................. normal
BRIGHTNESS control .......................................... normal
4. Screen(G2)
5. White Balance
Note : Test Equipment Required.
1. Pattern Generator
2. Degausser
3. DC Power Supply
4. Digital Multimeter
5. Oscilloscope
......................................................................................................................................................................................................................
Preparation :
In order to reduce the influence of geomagnetism on
the set's picture tube, face it east or west.
Switch on the set's power and degauss with the
degausser.

2-1. BEAM LANDING

Picture Mode: DYNAMIC
1. Input a white signal with the pattern generator.
Contrast Brightness
}
normal
2. Set the pattern generator raster signal to a green
raster.
3. Move the deflection yoke to the rear and adjust with
purity control so that the green is at the center and the blue and the red take up equally sized areas on each side. (See Figures 2-1 through 2-4.)
4. Move the deflection yoke forward and adjust so that
the entire screen is green. (See Figure 2-1.)
5. Switch the raster signal to blue then to red and verify
the condition.
6. When the position of the deflection yoke has been
decided fasten the deflection yoke with the screws and DY spacers.
7. If the beam does not land correctly in all the corners,
use a magnet to adjust it. (See Figure 2-4.)
Purity control corrects this area.
b
Fig. 2-2
Blue
Red
Green
Fig. 2-3
Disk magnets or rotatable disk magnets correct these
a
areas (a-d).
d
c
Deflection yoke positioning corrects these areas.
b
c
a
d
Fig. 2-1 Fig. 2-4
– 10 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100

2-2. CONVERGENCE

Before starting this adjustment, adjust the focus, horizontal size and vertical size.
Receive dot/hatch signal.
Pic mode: Soft.
(1) Horizontal and Vertical Static Convergence
Center dot
R G B
H. STAT VR
R
G
B
V. STAT
Magnet
RV750 H. STAT
CV Board
Operation of V.STAT magnet
If the V.Stat magnet is moved in the A” and B arrows, the red, green and blue dots moves as shown below.
A
B
A
B
G
R
B
B
G
R
Moved RV750 H.STAT.
the red, green and blue dots move as shown below.
A
RGGBB
B
R
4. BMC (Hexapole) Magnet. If the red, green and blue dots are not balanced or aligned, then use the BMC magnet to adjust in the manner described below.
RG B R G B R GB
1. (Moving vertically), adjust the V.STAT magnet so that the red, green and blue dots are on top of each other at the center of the screen.
2. (Moving horizontally), adjust the H.STAT control so that the red, green and blue dots are on top of each other at the center of the screen.
3. If the H.STAT variable resistor cannot bring the red, green and blue dots together at the center of the screen, adjust the horizontal convergence with the H.STAT variable resistor and the V.STAT magnet in the manner given below. (In this case, the H.STAT variable resistor and the V.STAT magnet influence each other, so be sure to perform adjustments while tracking.)
BMCPurity
BMC (Hexapole)
Purity
RB
G
RG
GB
RB
DY pocket
V.STAT
V.STAT
– 11 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
(2) Convergence Rough Adjustment
Preparation:
Before starting this adjustment, adjust the horizontal static convergence and the vertical static convergence
B
R
B
R
TLH
RB
YCH
TLH Insert TLH Correction Plate to DY Pocket
(Left or Right)
YCH Insert YCH VOL on DY
TLV Rotate TLV VOL on DY
XCV Rotate XCV Adj core on DY
(3) Screen corner Convergence
1. Affix a Piece A (90), conv. correct corresponding to the misconverged areas.
R B
ON DY:
TLV
XCV
YCH
TLV
XCV
TLV
DY pocket
TLH Plate
XCV
ba
a-d : screen-corner misconvergence
cd
– 12 –
DY pocket
a
d
Piece A (90), conv. correct
b
c
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100

2-3. FOCUS ADJUSTMENT

FOCUS adjustment should be completed before the W/B adjustment:
1. Receive digital monoscope pattern.
2. Set picture mode: DYNAMIC.
3. Adjust focus VR to obtain a just focus at the center of the screen.
4. Change receiving signal to white pattern and blue back.
5. Confirm MAGENTA RING is not noticeable. Incase magenta ring is obvious, then adjust FOCUS VR to balance magenta ring and FOCUS.
FOCUS
SCREEN

2-5. WHITE BALANCE ADJUSTMENT

1. Set to Service Mode (Refer Section 3-1: ADJUSTMENTS WITH COMMANDER)
2. Input white raster signal.
3. Set Picture to <DYNAMIC mode>
4. Select RDRV (02) with to 25 with
3 and 6.
5. Adjust WHBL GDRV (03) and BDRV (04) with
4 and adjust the data with 3 and 6 for best white
1 and 4 and fixed the value
1 and
balance in Highlight condition.
6. Write into the memory by pressing [MUTING] then
7. Adjust WHBL BKOR (00) and BKOG (01) with
4 and adjust the level with 3 and 6 for best white
-.
1 and
balance cut-off condition.
8. Write into memory by pressing [MUTING] then
-.
9. US model need to apply only for colour temperature in Neutral.

2-6. SUB BRIGHT ADJUSTMENT

1. Set to service mode.
2. Brightness set to 50%, Picture....Minimum
3. Select WHBL SBRT (10) with SBRT (10) data with
3 and 6 so that the third stripe
from right dimly lit.
4. Write into the memory by pressing [MUTING] then
5. GA models C/O: 20 IRE
S/G: 30 IRE
1 and 4 and adjust
-.
FLYBACK TRANSFORMER (T802-14") FLYBACK TRANSFORMER (T801-21")

2-4. G2 (SCREEN) ADJUSTMENTS

1. Set the PICTURE & BRIGHTNESS to STANDARD.
2. Put the Video input mode signal.
3. Connect R,G,B of the CV board cathode to oscilloscope.
4. Adjust Brightness to obtain the cathode value to value below.
5. Adjust G2 (screen) on the FBT until picture shows the point before cut off.
165 ± 2VDC
– 13 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
SECTION 3

CIRCUIT ADJUSTMENTS

3-1. ADJUSTMENTS WITH COMMANDER

Service adjustments to this model can be performed using the supplied remote commander RM-W100 and RM-W101.
a. ENTERING SERVICE MODE
With the unit on standby
t [DISPLAY] t 5 t [VOL $+% ] t [POWER]
This operation sequence puts the unit into service mode. This screen display is:
category in decimal item name in decimal NG service command frequency video input name
GEOM 006 HSIZ 031 x SERVICE 60 S VIDEO 1
release ID version in binary for factory color system (decimal?)
SUS01 0.69U 0001 1111 FF FF NTSC3 65535
111 11 11 1 7 11 FG xy 111 000000 000000
S : for Sony A:Aiwa
U S : US/Latin/Taiwan E U : Europe G A : General Area J P : Japan
item no. service data NVM field channel no./
software service data reserved power on time
Status Byte Status Byte
Flash DCXO #1 SSD #2 SSD
VDSP_C Flag
CO_LOCKED
VDSP
Detected Stereo Type (Direct Value from CZ_ Stereo_Mode)
111 Needed for Nicam DCXO aligment Purpose
xy Value of x = 0 - Unknown, 1 - BTSC, 2 - A2, 3 - NICAM,
4 - KOREAN, 5 - Japan, 6 - AV Stereo Value of y = 0 - Mono, 1 - Stereo, 2 - Bilingual, 4 - SAP/Single
0 1 : serial no. of the M/P release
for each destination
b. METHOD OF CANCELLATION FROM SERVICE MODE
Set the standby condition (Press [POWER] button on the commander), then press [POWER] button again, hereupon it becomes TV mode.
c. METHOD OF WRITE INTO MEMORY
1. Set to Service Mode.
2. Press
3. Change item by pressing
1 (UP) and 4 (DOWN), to select the adjustment item.
3, 6.
4. Press [MUTING] button to indicate WRITE on the screen.
5. Press
- button to write into memory.
1, 4 Select the adjustment item.
r
3, 6 Raise/lower the data value.
r
[MUTING] Writes.
r
- Executes the writing.
d. MEMORY WRITE CONFIRMATION METHOD
1. After adjustment, pull out the plug from AC outlet, and then plug into AC outlet again.
2. Turn the power switch ON and set to Service Mode.
3. Call the adjusted items again to confirm adjustments were made.
– 14 –
e. OTHER FUNCTION VIA REMOTE COMMANDER
7, - All the data becomes the values in memory. 8, - All user control goes to the standard state. Display, - Service data initialization (Be sure not to use usually.) 2, 5 Select Device or Category

3-2. ADJUSTMENT METHOD

Item Number 000 HPOS This explanation uses H POSITION as an example.
1. Select "000 HPOS" with the
2. Raise/lower the data with the
3. Select the optimum state. (The standard is IF for PAL reception.)
4. Write with the [MUTING] button. (The display changes to WRITE.)
5. Execute the writing with the SERVICE.)
Example on screen display :-
GEOM 000 HPOS 039 SERVICE 50 VIDEO 1
1 and 4 buttons, or 2 and 5.
3 and 6 buttons.
- button. (The WRITE display will be changed to red color while excuting, and back to
GREEN
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
Adjusted with [3] and [6] buttons.
GREEN
GEOM 000 HPOS 039 WRITE 50 VIDEO 1
write with [MUTING].
RED
GEOM 000 HPOS 039 WRITE 50 VIDEO 1
Use the same method for all Items. Use [MUTING], then execute the write with
-.
Write executed with [0].
1 and 4 to select the adjustment item, use 3 and 6 to adjust, write with
The WRITE display then returns to green SERVICE
Note :1.In [WRITE], the data for all items are written into memory together.
2. For adjustment items that have different standard data between 50Hz or 60Hz, be sure to use the respective input signal after adjustment.
– 15 –
Adjustment Item Table
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD)deliateD(eulaVlaitinI/sserddAMVN
yrogetaC.oNemaNceDceD )sserddAevalS(nommoC050605w06w
MOEG000SOPH130360TSUJDA)SH(tfihSlatnoziroH )BGRNPJ+(06w/05w/06/05rossecorP-VT
24242424
100RAPH130360TSUJDAmargolellaraPlatnoziroH06w/05w/06/05)hA8(
13131313
200WOBH130360TSUJDAwoBlatnoziroH06w/05w/06/05
13131313
300NILV130360TSUJDAytiraeniLlacitreV06w/05w/06/05
13131313
400RCSV130360TSUJDAllorcSlacitreV06w/05w/06/05
13131313
500ZISH130360TSUJDA)WE(htdiWWE06w/05w/06/05
52525252
600WPWE130360TSUJDA)WP(htdiW/alobaraPWE )BGRNPJ+(06w/05w/06/05
13131313
700POCU710360TSUJDAalobaraPrenroCreppUWE06w/05w/06/05
13131313
800POCL710360TSUJDAalobaraPrenroCrewoLWE06w/05w/06/05
13131313
900ZTWE130360TSUJDAmuizeparTWE06w/05w/06/05
13131313
010PLSV130360TSUJDA)SV(epolSlacitreV06w/05w/06/05
13131313
110ZISV510360TSUJDAedutilpmAlacitreV06w/05w/06/05
51515151
210ROCS410360TSUJDA)CS(noitcerroC-S06w/05w/06/05
52525252
310SOPV130360TSUJDA)HSV(tfihSlacitreV06w/05w/06/05
13131313
410LBH000100XIFedoMgniknalBBGR06w/05w/06/05
10101010
510FBW700510XIF)FBW(gniknalBediWfognimiT06w/05w/06/05
70707070
610RBW700510XIF)RBW(gniknalBediWfognimiT06w/05w/06/05
01010101
710LBS000100XIFgniknalBecivreSenon00
810YPOC000100XIFaeraMVNzH06/05llaotatadOEGehtypoCenon00
– 16 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
– 17 –
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD )deliateD(eulaVlaitinI/sserddAMVN
yrogetaC.oNemaNceDceD
)sserddAevalS(nommoCpmeTloC
)rehtoHGIH(
pmeTloC
)rehtoWOL(
pmeTloC
)rehtoMRON(
pmeTloC
)VUYHGIH(
pmeTloC
)VUYWOL(
pmeTloC
)VUYLAMRON(
pmeTloC
)BGRHGIH(
pmeTloC
)BGRWOL(
pmeTloC
)BGRMRON(
srehtOBGRVUYedomciP
0
edomciP
1
edomciP
2
edomciP
3
LBHW000ROKB130360TSUJDARtesffOleveLkcalB )srehtO/BGR/VU(*)lamroN/WOL/HGIH(pmetlocrossecorP-VT
131313131313131313
100GOKB130360TSUJDAGtesffOleveLkcalB )srehtO/BGR/VU(*)lamroN/WOL/HGIH(pmetloc)hA8(
131313131313131313
200VRDR730360XIFRtnioPetihW )srehtO/BGR/VU(*)lamroN/WOL/HGIH(pmetloc)HA8(orP-VT
737373737373737373
300VRDG730360TSUJDAGtnioPetihW )srehtO/BGR/VU(*)lamroN/WOL/HGIH(pmetloc
131313131313131313
400VRDB730360TSUJDABtnioPetihW )srehtO/BGR/VU(*)lamroN/WOL/HGIH(pmetloc
131313131313131313
500GPL000100XIFteserPniaGBGR enon10
600RGP130721XIF)RGP(RniaGteserP enon
**
700GGP130721XIF)GGP(GniaGteserP enon
**
800BGP130721XIF)BGP(BniaGteserP enon
**
900FONG000510XIFtesffOniaGteserP enonpoolCCC51
010TRBS130360TSUJDAssenthgirB-buS VUY/BGR/srehtO
131313
110ORBS000300XIF)ciPtnegilletnI(tesffOssenthgirB-buS enon00
210LGE000100XIFmetsySCCCnipooLniaGelbanE enon10
310LGS000300XIFmetsySCCCnitnerruChgiHfonoitceleS enon00
410BKA000100XIFnoitazilibatStnerruCkcalB enon00
510SBC000100XIFgnitimiLtnerruCmaeBfoecneuqeSlortnoC enon00
610BBGR000300XIFgniknalBBGR enon00
710GBLB000100XIFtuptuOneerG&eulBfogniknalB enon00
810BFO000100XIFeulBtesffOleveLkcalB enon10
910RBSN000510XIFtesffOssenthgirBdradnatSnoN enon50
020PBW000300XIF)woL:3,2,lamroN:1,hgiH:0(gnitteSpmeTroloC edoMerutciP
00102010
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD )deliateD(eulaVlaitinI/sserddAMVN
yrogetaC.oNemaNceDceD
)sserddAevalS(nommoCVUYlap05
)VT(
lap05
)oediV(
maces05
)VT(
maces05 )oediV(
VT06oediV06VUY05VUY06BGR05BGR06edomciP
0
edomciP
1
edomciP
2
edomciP
3
ocE*cimanyD
)npJ(dts
ocE*cimanyD
)npJ(hcum
ocE*dradnatS
)npJ(dts
ocE*dradnatS
)npJ(hcum
dtsocE
)npJ(
hcumocE
)npJ(
VToediVVT
ediW
oediV ediW
MVA
)npJ(
ediWVA
)npJ(
JDAS000XAMP360360TSUJDAmumixaMerutciP )BGRNPJ+(>ediW/lamroN</)ediW/lamroN(*)oediV/VT( rossecorP-VT
737373730000
100EUHS700510TSUJDAeuH-buS oediV/VT
7070
200PHSS510360XIFssenprahS-buS )BGRNPJ+(VUY/oediV/VT
**
******
300OHSS000300XIF)ciPtnegilletnI(tesffOssenprahS-buS enon20
400LOCS130360TSUJDAroloC-buS /)oediv(maces05/)vt(maces05/)oediv(lap05/)vt(lap05
BGR06/BGR05/VUY06/VUY05/oediv06/VT06
13131313131313131313
500OOCS000300XIF)ciPtnegilletnI(tesffOroloC-buS enon20
600CIP130721XIF;)dilavni(001>,)dilav(001-0:AG[lortnoCerutciP
])dilavni(6tiberongi;)dilav(36-0:srehtO
)ataDteseRresU=lanosreP:AG(ledoMerutciP
0010856001
700LOC130721XIF;)dilavni(001>,)dilav(001-0:AG[lortnoCroloC
])dilavni(6tiberongi;)dilav(36-0:srehtO
)ataDteseRresU=lanosreP:AG(ledoMerutciP
65050405
800TRB130721XIF,)dilav(001-0:AG[lortnoCssenthgirB
tiberongi;)dilav(36-0:srehtO;)dilavni(001>
])dilavni(6
)ataDteseRresU=lanosreP:AG(ledoMerutciP
05050605
900EUH130721XIF;)dilavni(001>,)dilav(001-0:AG[lortnoCeuH
])dilavni(6tiberongi;)dilav(36-0:srehtO
)ataDteseRresU=lanosreP:AG(ledoMerutciP
05050505
010PHS130721XIF,)dilav(001-0:AG[lortnoCssenprahS
tiberongi;)dilav(36-0:srehtO;)dilavni(001>
])dilavni(6
)ataDteseRresU=lanosreP:AG(ledoMerutciP
06050505
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
KV-AR21M30/AR21M90/AR21M61/AR21M81
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD )deliateD(eulaVlaitinI/sserddAMVN
yrogetaC.oNemaNceDceD )sserddAevalS(nommoCsrehtOBGRVUY)VT(LAP)VT(CSTN)VT(MACES)oediV(LAP)oediV(CSTN)oediV(MACESTUPNI-SMACESCSTNVT
CY000QRFP000300XIFyaleDdnaycneuqerFretneCgnikaeP rossecorP-VT***
100APR####300XIFtoohSrevO&erPoitaR rehto/VT
20
20
200OPR200300XIFskaePevitageN&evitisoPfooitaR rehto/VT
20
20
300YLDY210510XIFyaleD-Y TUPNI-S/VUY+)OEDIV/VT(*)MACES/CSTN/LAP(
** * * * * * *
400TAMC000300XIFxirtaM)ASU/napaJ(CSTNroMACES-LAP )BGRNPJ(00
00
500LCA100100XIFgnitimiLroloCcitamotuA 10
600BC000100XIFycneuqerFretneCssapdnaBamorhC )xif0:oediV*(VThtiwylnodilav10
700OBS100300XIFtesffOkcalBMACES 00
800ESHC100300XIFytivitisneStnedICSTN/LAP 20
900OLC000100XIFretliF)lleB(ehcolCfoycneuqerFretneC 00
010PRTC000100XIFedoMparTamorhC srehto/MACES
00
10
110SPB000100XIFeniLyaleDdnab-esaBamorhCfossapyB srehto/CSTN
***
***
210OCF000100XIFnOroloCdecroF 00
310TNIT130360XIFlortnoCtniTdnaB-esaB srehto/VUY
13
13
410VUT000100XIFslangiSVUnolortnoCtniT 00
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD )deliateD(eulaVlaitinI/sserddAMVN
yrogetaC.oNemaNceDceD )sserddAevalS(nommoC0506srehtoVUYVToediVtxeteleTpi-VTlangisoN
CNYS000SYS000100XIFtupnICNYSYnonoitazinorhcnyS 00
100OF000300XIFtnatsnoCemiT1esahP )FR(langisoNrogninuTotuA/txeteleT/oediV/FFOPIVT/NOPIVT
3030100000
200DIV000100XIFedoMtnedIoediV 06/05
0000
300LSF000100XIFcnySlacitreVrofleveLgnicilSdecroF 00
400LSS000100XIFrotarapeScnySleveLgnicilS 06/05
0000
500DIVS100700XIFnoitacifitnedIoediVrofnoitceleSecruoS srehtO/VUY
0070
600FROF000300XIFycneuqerFdleiFdecroF 30
700KVM000100XIFgniyeKnoisiVorcaM 10
RM-W101 RM-W100
18
19
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD)deliateD(eulaVlaitinI/sserddAMVN
yrogetaC.oNemaNceDceD )sserddAevalS(nommoCVUYVToediV
WS0002VC000100XIFnoitceleSlangiStupnI2SBVC 00
100OVS100300XIF84@niPISBVC/OVS/OVFIfonoitcnuFVUY/oediV/VT
201010
200LFD000100XIFnoitcetorPhsalF 00
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD )deliateD(eulaVlaitinI/sserddAMVN
yrogetaC.oNemaNceDceD
)sserddAevalS(nommoCsrehtOBGReviLVT
)nyD(
VT
)srehtO(
oediV
)nyD(
oediV
)srehtO(
pmeTroloC
)HGIH(
pmeTroloC
)srehtO(
roloC
)WOL(pmeT
pmeTroloC
)LAMRON(
TCIP000LDAC700510XIFleveLevirDedohtaC 00
100AFC000300XIFedoMretliFbmoC ***
200COS200300XIFleveLgnippilCtfoS )hA8(00
300LWP100100XIFhctiwSgnitimiLetihWkaeP 10
400LTHW600510XIFgnitimiLetihWkaeP 00
500MAG100100XIFammaG 00
600STW100300XIFhctertSetihWdnalortnoCammaGsrehtO/eviL
10
10
700RFT000100XIFlangiSecnanimuLfooitaRrefsnarTCD )BGRNPJ+(srehtO/eviL
100010
800ROC300300XIFgniroC )srehto/anyD(*)oediV/VT(
00000000
900OROC000100XIF)ciPtnegilletnI(tesffOgniroC 00
010SKB300300XIFhctertSkcalBsrehto/BGR
2020
110SAA100100XIFhctertSkcalBehtffohctiwSotaerAkcalB 00
210KSD000100XIFlortnoCnikScimanyD 00
310SLB000100XIFhctertSeulB )SREHTO/HGIH(pmetloc
0000
410SLBN000100XIFtiucriChctertSeulBnoitarepO 00
510RRN000100XIFnoitcudeRdeRnoN )LAMRON/WOL/HGIH(pmetloc
10
1010
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
KV-AR21M30/AR21M90/AR21M61/AR21M81
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD )sserddAevalS(
FIV000DFIO630360XIFrotaludomeDFItesffO rossecorP-VT63
100TCGA130360XIFrevo-ekaTCGA )hA8(13
200MTS000100XIFedoMgninuThcraeS 10
300DG000100XIFlangiS1SBVCnoyaleDpuorG 00
400SCGA100300XIFdeepSCGAFI 10
500IFF000100XIFLLPFIretliFtsaF 00
600PMAO300300XIF)metsyS'L&Lylno(edutilpmAlangiStuptuOoediV 30
700IAV000100XIF)metsyS'L&Lylno(noitcerroCedutilpmAlangiStuptuOImetsyS 00
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD)deliateD(eulaVlaitinI/sserddAMVN
yrogetaC.oNemaNceDceD
)sserddAevalS(nommoCedomciP
0
edomciP
1
edomviP
2
edomciP
3
MV000DBGR300700XIFtuptuOMVottuptuOBGRfoyaleDenonrossecorP-VT20
100AMV300300XIFtuptuOMVfoedutilpmAenon)hA8(
**
200PAMV200300XIF)FFO:3,2,woL:1,hgiH:0(gnittesMVedoMerutciP
00102000
300OMMV300300XIFedoMMV 10
RM-W101 RM-W100
20
21
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD )sserddAevalS(
MEDS000SWMF000300XIFrotaludomeDMFrofnoitceleSwodniW rossecorP-VT20
100SSQ100100XIF)ledoMAGtpecxe(edoMreifilpmA)SSQ(dnuoStilpSisauQ )hA8(10
200BPB000100XIFretliFssapdnaBdnuoSfossapyB 00
300OLMA000100XIFdnuoSMAroflangiStuptuOoiduA 00
400CVPH000100XIFlortnoCemuloVenohPdaeH 00
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveDnommoC
yrogetaC.oNemaNceDceD )sserddAevalS(
TXT000VXT930360XIFspilihProfnoitisoPlacitreVtxeteleT redoceDtxeT93
100DHT500721XIFtfihSegdEevitcAcnus-HtxeteleT 50
200RBT400510XIFssenthgirBBGRtxeteleT 11
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
KV-AR21M30/AR21M90/AR21M61/AR21M81
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD
)sserddAevalS(
)deliateD(eulaVlaitinI/sserddAMVN
yrogetaC.oNemaNceDceD nommoC)oruE(L-VTVToediVffOWOW/SRSdnuorrusurToeretsIonomI
PSDS000MVA200700XIFedoMLVA DSS20
100VVA500510XIFleveLecnerefeRLVA )h0B(90
200LBB000510XIFruotnoCEBB
****
300HBB000510XIFssecorPEBB
****
400WLBB000510XIFtesffOruotnoCEBB
****
500FOVS000510XIFtesffOemuloVedoMtceffE/dnuorruS onomI/oeretsI/dnuorrusurT/)WOW/SRS(ffO
0070002000
600FOVI000700XIFtesffOevitisoPemuloVretsaM 60
700FOVE000700XIFtesffOevitageNemuloVretsaM 60
800DAL000130XIFtsujdAleveLredoceD 50
900MAL000130XIFtsujdAleveLonoM 50
010NAL000130XIFtsujdAleveLmaciN 71
110SAL000130XIFtsujdAleveLPAS 80
210AAL000130XIFtsujdAleveLCDA oediV/Lnon-VT/L-VTI)oruEnoN(oediV/vT
000000
310FES300700XIFtceffEoeretS/onoMelbidercnI onomI/oeretsI
5030
410L1A000552XIFtfeLemuloV1XUA 00
510R1A000552XIFthgiRemuloV1XUA 00
610SAB800510XIFtesffOssaBniaM
****
710ERT800510XIFtesffOelberTniaM
****
8101QE800510XIFtesffO)zH001(dnaBlennahCniaMrezilauqE
****
9102QE800510XIFtesffO)zH003(dnaBlennahCniaMrezilauqE
****
0203QE800510XIFtesffO)zH0001(dnaBlennahCniaMrezilauqE
****
1204QE800510XIFtesffO)zH0003(dnaBlennahCniaMrezilauqE
****
2205QE800510XIFtesffO)zH0008(dnaBlennahCniaMrezilauqE
****
320TCFB500700XIFlortnoCEBBdnaBUD,EBD
****
420NECS100510XIFlortnoCretneCD3SRS 40
520APSS000510XIFlortnoCecapSD3SRS 10
620WHBB000510XIFedomWOWnitesffossecorpEBB
****
720ERTS200700XIFedomdnuorrusroftesffOelberT
****
820THBB000510XIFedomVTnitesffOEBB 00
920AWD000000XIF???AWD 00
030ERTT200700XIFedoMVTnitesffOelberT 20
RM-W101 RM-W100
– 22 –
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD
)sserddAevalS(
nommoC
yrogetaC.oNemaNceDceD
CEDS000UTPM300510XIF)CSTB(noitcetedtolipXPMrofdlohserhTreppU DSS20
100LTPM900510XIF)CSTB(noitcetedtolipXPMrofdlohserhTrewoL )h0B(50
200UTPS300510XIFnoitcetedreirracPASrofdlohserhTreppU 80
300LTPS600510XIFnoitcetedreirracPASrofdlohserhTrewoL 51
400HT1C000130XIF1CSfonoitcetedrofdlohserhTlamroN 00
500PA1C000130XIF1CSfonoitcetedrofdlohserhTmargorPotuA 00
600HTPS000130XIFPASfoetumotuarofdlohserhTesioN 00
700YHPS400510XIFPASfoetumotuarofezissiseretsyH 30
800HTMF000130XIFdradnats2AMFni2CSfoetumotuarofdlohserhTesioN 81
900YHMF400510XIFdradnats2AMFni2CSfoetumotuarofezissiseretsyH 70
010HTTB000130XIFreirracoeretsCSTBfoetumotuarofdlohserhTesioN 00
110YHTB400510XIFoeretsCSTBfoetumotuarofezissiseretsyH 30
210HTJE000130XIFreirracbusMFJAIEfoetumotuarofdlohserhTesioN 00
310YHJE400510XIFreirracbusMFJAIEfoetumotuarofezissiseretsyH 40
410YLNO000100XIFtuptuoCEDnoMACINdetalerylnoecudorpeR 00
510MAXE000100XIF)PEDD(LdradnatsnietumotuafoesacniecruoskcabllaF 00
610TMIN000100XIF)PEDD(etarrorretibnodnepednoitcnufetumotuaMACIN 00
710ELIN001552XIF)PEDD(timilrorrerewolMACIN 05
810EUIN002552XIF)PEDD(timilrorrereppuMACIN 002
910DMPE100300XIF)PEDD(gnimmargorPysaECEDMED 20
020SDTS910130XIFsedomSSSdnaDSArofdexelpitlumstiB 13
120AMVO100100XIFnoitpadanoitaludomrevoMF 00
220WBLF000300XIFhtdiwdnabretlifrotaludomedMA/MF 30
320DMDI000300XIFedomSSSnideepstnediMF 00
420LAPF000100XIFgnidocedCSTBrofycneuqefeniL 00
520TMVO100200XIFlanimonotevitalerdlohserhtlevelnoitaludomrevO 30
620IXCD000100XIFretrevnIlortnoCgnilacSOXCDMACIN *
720GXCD000700XIFniaGlortnoCgnilacSOXCDMACIN *
820LLCD110510XIF)L(timiLlortnoCgnilacSOXCDMACIN 00
920HLCD000130XIF)H(timiLlortnoCgnilacSOXCDMACIN *
030UEDI100300XIFDTS2AnaeporuErofgnittesDOMDI 00
130RKDI100300XIFDTSMnaeroKrofgnittesDOMDI 00
230PJDI100300XIFDTSJAIErofgnittesDOMDI 10
– 23 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
KV-AR21M30/AR21M90/AR21M61/AR21M81
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD
)sserddAevalS(
nommoCetoN
yrogetaC.oNemaNceDceD
BTPO000LLAI000100XIF)MVNnideziromemton(hctiwSetirWdradnatS 00
1001BPO000552XIF)detalermetsyS(1noitpO
*****
kramerroF *****
otreferesaelP
llaroftiBnoitpO
63egaPnosledom
45egaPot
2002BPO000552XIF)detalerlangiSoediV(2noitpO
*****
3003BPO000552XIF)detalergnidoceDoeretS(3noitpO
*****
4004BPO000552XIF)suoenallecsiM(4noitpO
*****
5005BPO000552XIF)suoenallecsiM(5noitpO
*****
6006BPO000552XIF)detaleregaugnaLDSO(6noitpO
*****
JVTytilanoitcnuF.tinIegnaRATADnoitcnuFetoN&elbaTemaNeciveD
)sserddAevalS(
)deliateD(eulaVlaitinI/sserddAMVN
yrogetaC.oNemaNceDceD nommoC0506
MTPO000THSA600700XIF)nim5*atad(remitffotuhsotuA 00
100BDSO000510XIFssenthgirbDSO h06orciM/RMM50
200HDSO500510XIFnoitisoPlatnoziroHDSO h06orciM/RMM50
300VDSO730360XIFnoitisoPlacitreVDSO 06/05h06orciM/RMM
3613
400ETUM000100XIF)delbane=1(hctiwSetuMlangiSoN 00
500LUFR510510XIF)hf0nehwelbasiD(dekcolnUretfaretnuoCegnahClangiSFR 40
600KLFR510510XIF)hf0nehwelbasiD(dekcoLretfaretnuoCegnahClangiSFR 00
700LUVA510510XIF)hF0nehwelbasiD(dekcolnUretfaretnuoCegnahClangiSVA 40
800KLVA510510XIF)hF0nehwelbasiD(dekcoLretfaretnuoCegnahClangiSVA 00
900GNAL000300XIFnoitidnocgnippihsegaugnalDSO 00
010TXTH000100XIFwsrotarepescnyS )A8(rossecorP-VT00
110SSMC000100XIFwscnyS )A8(rossecorP-VT10
210OXCD060592XIFeulaVOXCD PSD/h06orciM/RFS95
310LBXE000510XIFesioNetihWetanimilEotremiTgniknalBdednetxE 70
410SYST000300XIF )ledoMAG(]K/D:3,M:2,I:1,G/B:0[teseRtseTtaMVNnisySVTeziromeM 00
510UOVT100100XIFlangistuohtiwetuM:1,ffoetuMsyawlA:0noitidnocetumtuoVT 00
RM-W101 RM-W100
24
NOTE
shaded items are fixed data.
Standard data listed on the Adjustment Item Table are reference values, therefore it may be different for each model and for each mode.
Note for Different Data Those are the standard data values written on the microprocessor. Therefore, the data values of the modes and stored respectively in the memory.
In case of a device replacement, adjustment by rewriting the data value is necessary for some items.
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
Data Variant depend on models
Category No Name Model Data
WHBL 006 PGR With VM A864 69
Without VM A864 61
007 PGG With VM A865 69
Without VM A865 61
008 PGB With VM A866 69
Without VM A866 61
Category No Name Model Data
VM 001 VMA With VM A87D 03
Without VM A87D 00
Category No Name Model Table
PAL NTSC SECAM PAL NTSC SECAM YUV S-Input
(TV) (TV) (TV) (VIDEO) (VIDEO) (VIDEO)
YC 003 YDLY Comb Model A851 08 A852 08 A853 08 A8D8 11 A8DC 09 A8DD 11 A8DE 09 A8DF 09
Non-Comb Model A851 02 A852 02 A853 10 A8D8 2 A8DC 2 A8DD 2 A8DE 09 A8DF 09
Category No Name Model Table
TV Video YUV
SADJ 002 SSHP
Category No Name Model Data
PICT 001 CFA Comb models A86D 00
Category No Name Model Data
YC 000 PFRQ Comb models A86B 01
Category No Name Model Table
YC 011 BPS Comb models AAF6 01 AAF5 00
Category No Name NVM Address AR21 BT21 HW21 AR14 HW21 BM14/21
SDSP 002 BBL A8E6 01 00 00 01 00 00
003 BBH A8E6 05 00 00 04 00 00 004 BBLW A839 06 06 06 06 06 06 016 BAS A8FA 13 13 00 00 13 00 017 TRE A8FB 14 14 12 13 14 00 018 EQ1 AA00 12 09 00 07 11 00 019 EQ2 AA01 04 09 01 00 00 00 020 EQ3 AA02 10 09 00 00 00 00 021 EQ4 AA03 09 10 11 10 00 00 022 EQ5 AA04 10 11 11 00 12 00 023 BFCT AAF9 05 00 00 05 00 00 026 BBHW AA23 00 00 00 00 00 00 027 STRE AA24 01 01 01 01 01 01
21" Comb models
21"Non-Comb models &
All 14" models
Non-Comb models A86D 01
Non-Comb models A86B 00
Non-Comb models AAF6 00 AAF5 00
A859 35 A85A 35 A898 35
A859 35 A85A 38 A898 35
NTSC Others
series (AV Stereo) 3D series non-3D & BT21
Category No Name NVM Address Stereo models Non-stereo models
SDEC 26 DCXI AA48 01 00
027 DCXG AA48 03 00 029 DCLH AA47 06 00
– 25 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
ITEM INFORMATION No. OPB1
Item
KV-AR21M30
KV-AR21M61 (GE)
KV-AR21M61 (Malaysia)
KV-AR21M61 (Thailand)
KV-AR21M81
KV-AR21M90
No. OPB2
Item
KV-AR21M30
KV-AR21M61 (GE)
KV-AR21M61 (Malaysia)
KV-AR21M61 (Thailand)
KV-AR21M81
KV-AR21M90
Speed Search
0
0
0
0
0
0
SPEED SEARCH (Time of speed search) 00 = disabled (original cycle speed)
TV System Selection 0 = disabled, 1 = enabled
D1(JPN)
AV Multi/
PAM(GA 0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
M/N(US)
0
0
0
0
0
0
Component
1
1
1
1
1
1
L
0
0
0
0
0
0
Composite (SCART) Color Decording
1
1
1
1
1
1
M
1
1
1
1
1
1
0
0
0
0
0
0
B/G
1
1
1
1
1
1
01 = 4 time speed from the original 10 = 6 time speed from the original 11 = 8 time speed from the original
SECAM
1
1
1
1
1
1
I
1
1
1
1
1
1
0
0
0
0
0
0
D/K
1
1
1
1
1
1
0
0
0
0
0
0
DEC
79
79
79
79
79
79
DEC
116
116
116
116
116
116
D1 (D1 Terminal) 0 = not available, 1 = available AV Multi/ (AV Multi Terminal) - JP 0 = not available, 1 = available PAM Portable Audio Mode - GA 0 = not available, 1 = available Component (Component [YCbCr] Terminals) 0 = not available, 1 = available Composite (No. of Composite Terminals) 00 = no composite terminal
(Euro:no Scart) BX1L:No Video
(SCART) (No. of SCART Terminals) 01 = 1 composite terminal
(Euro:1 Scart) BX1L:2 Video in
10 = 2 composite terminals
(Euro:2 Scart) BX1L:3 Video in
11 = 3 composite terminals
(Euro:no terminal) BX1L:4 Video in SECAM (SECAM Color System) 0 = not available, 1 = available Color decoding (Color Crystal Selection) 00 = PAL/NTSC/SECAM (Multi)
01 = NTSC (3.58MHz) 10 = PAL/NTSC/SECAM (4.43MHz) 11 = PAL/NTSC (Tri-Norma)
– 26 –
No. OPB3
Item
KV-AR21M30
KV-AR21M61 (GE)
KV-AR21M61 (Malaysia)
KV-AR21M61 (Thailand)
KV-AR21M81
KV-AR21M90
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
HDEV
HDEV (High Deviation Mode) 0 = disabled, 1 = enabled NICAM ST (NICAM Stereo) 0 = disabled, 1 = enabled NICAM BI (NICAM Bilingual) 0 = disabled, 1 = enabled A2 ST/BI (A2 [West German]
Thai Bilingual (A2 [Thai] Bilingual)
JP/US ST (JP/US Stereo) 0 = disabled, 1 = enabled Korean ST (Korean Stereo) 0 = disabled, 1 = enabled MONO (Monaural Model) 0 = Stereo (SSD) Model
0
0
0
0
0
0
NICAM ST
1
1
1
1
0
1
NICAM BI
1
1
1
1
0
1
Stereo/Bilingual) 0 = disabled, 1 = enabled
or Force SAP if JP/US ST is active 0 = disabled, 1 = enabled
A2 ST
1
1
1
1
0
1
Thai Bilingual
0
0
0
1
0
0
0
0
0
0
0
0
Korean ST
0
0
0
0
0
0
JP/US ST
1 = Monuaral Model
MONO
0
0
0
0
0
0
DEC
112
112
112
112
00
112
No. OPB4
Item
KV-AR21M30
KV-AR21M61 (GE)
KV-AR21M61 (Malaysia)
KV-AR21M61 (Thailand)
KV-AR21M81
KV-AR21M90
Firmware/
SMAT
1
1
1
1
1
1
Firmware (SSD Firmware Downloading) 0 = disabled, 1 = enabled SMAT Surround Matrix 0 = Active, 1 = Passive 1 spk Models 1 Speaker Models 0 = 2 or 3 Speaker Models,
VM (Velocity Modulation) 0 = disabled, 1 = enabled Equalizer (5-band Equalizer Model) 0 = Bass/Treble Model, 1 = Equalizer Model Surround (US/GA Surround Selection) 0 = Off/Simulated/Surround
V-Chip (V-Chip Model) 0 = Channel Block Model (no rating)
TOP (Forced TOP) 0 = Auto Mode (TOP/FLOF), 1 = Forced TOP TEXT (Teletext Model) 0 = Non-Teletext Model, 1 = Teletext Model
1 spk
Models
0
0
0
0
0
0
VM
Equalizer
1
1
1
1
1
1
Surround
1
1
1
1
1
1
1
1
1
1
1
1
V-Chip
0
0
0
0
0
0
1 = 1 speaker Models
1 = Off/Simulated/WOW/TruSurround (US) 1 = Off/Simulated/SRS (3D) Surround (GA)
1 = Parental Control Model (rating)
To p
0
0
0
0
0
0
Te x t
0
1
1
1
1
0
DEC
184
185
185
185
185
185
– 27 –
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
No. OPB5
Item
KV-AR21M30
KV-AR21M61 (GE)
KV-AR21M61 (Malaysia)
KV-AR21M61 (Thailand)
KV-AR21M81
KV-AR21M90
Full
Surround
0
0
0
0
0
0
Full Surround (Full Surround option) 0 = Normal Surround Model
No Surround (No Surround Model) 0 = Surround Model, 1 = Non-Surround Model Forced 60 (Forced 60Hz in no signal) 0 = 50Hz, 1 = 60Hz ASD (Automatic Standard Detection) 0 = disabled, 1 = enabled Tilt (Tilt Correction/PIC Rotation) 0 = disabled, 1 = enabled IP Plus (Intelligent Picture Plus) 0 = disabled, 1 = enabled IP (Intelligent Picture) 0 = disabled, 1 = enabled Wide (Wide Mode/V-Compressed) 0 = disabled, 1 = enabled
No
Surround
0
0
0
0
0
0
Forced 60
0
0
0
0
0
0
ASD
1
1
1
1
1
1
Tilt
1
1
1
1
1
1
IP Plus
1
1
1
1
1
1
1 = Full Surround Model
(Off/simulated/surround/
SRS/WOW/TruSurround)
IP
1
1
1
1
1
1
Wide
1
1
1
1
1
1
DEC
31
31
31
31
15
31
– 28 –
No. OPB6
Item
KV-AR21M30
KV-AR21M61 (GE)
KV-AR21M61 (Malaysia)
KV-AR21M61 (Thailand)
KV-AR21M81
KV-AR21M90
KV-AR21M30/AR21M90/AR21M61/AR21M81
RM-W101 RM-W100
GA US
1
1
1
1
1
1
GA US (US Model Destination) 0 = US/CANADA/Latin
Latin (US Model Latin Destination) 0 = US/CANADA (No Volume Figure Display)
Feature 2 (Temporary for BX1L) 0 = Comb Not available
Feature 1 (Temporary for BX1L) 0 = PiP Not Available
Latin
0
0
0
0
0
0
REV
0
0
0
0
0
0
REV
0
0
0
0
0
0
OSD Language Selection
1
1
1
x
0
1
0
0
0
x
1
0
1 = Taiwan/Korea/Philippine
(Wake-up timer enable) (GA Surround Spec:OFF, SIMULATED, SRS)
1 = Latin (Volume Figure Display)
1 = Comb available
1 = PiP available
0
0
0
1
0
0
DEC
0
0
0
x
0
0
136
136
136
136
132
136
OSD Language Selection 01xx = French (English always available except JP) US 0x1x = Spanish
0xx1 = Portuguese
US 1x1x = Complicated Chinese (GA NTSC) 1xx1 = Korean
1xxx = Simplified Chinese
GA x1xx = Arabic
xx1x = Thai xxx1 = Vietnamese
0000 = Destination ADE
EU 0001 = Destination BL
0010 = Destination KR 0011 = Destination U
– 29 –
Loading...
+ 224 hidden pages