AV Preset ............................................................................................................................................12
PIP Position ........................................................................................................................................16
• Dangerously high voltages are present inside the TV.
• Operate the TV only between 220 - 240 V AC.
For your own safety, do not touch
any part of the TV, the power cord
and the antenna cable during
lightning storms.
Do not operate the TV if any
liquid or solid object falls into it.
Have it checked immediately by
qualified personnel only.
place any objects on the TV.
Do not
For children’s safety, do not leave
children alone with the TV. Do not
allow children to climb onto it.
Do not block the ventilation
openings of the TV.
Do not install the TV in a
confined space, such as a
bookcase or built-in cabinet.
Do not plug in too many
appliances to the same power
socket. Do not damage the
power cord.
To prevent fire or shock hazard, do
not expose the TV to rain or
moisture.
Clean the TV with a dry and
soft cloth.
Do not use benzine, thinner, or
any other chemicals to clean
the TV. Do not scratch the
picture tube.
Do not open the cabinet and the
rear cover of the TV as high
voltages and other hazards are
present inside the TV. Refer
servicing and disposal of the TV
to qualified personnel.
Your TV is recommended for
home use only.
Do not use the TV in any vehicle
or where it may be subject to
excessive dust, heat, moisture or
vibrations.
4
Safety Information
Install the TV on a stable TV
stand and floor which can
support the TV set weight.
Ensure that the TV stand
surface is flat and its area is
larger than the bottom area of
the TV.
Pull the power cord out by the
plug. Do not pull the power
cord itself. Even if your TV is
turned off, it is still connected to
the AC power source (mains) as
long as the power cord is
plugged in. Unplug the TV
before moving it or if you are not
going to use it for several days.
Overview of Remote Control Buttons
@¡
@º
!ª
!•
!¶
!§
!∞
!¢
!£
!™
9 Recording button: If Media Selector is switched to VCR, press this button to record programmes.
!º Media Selector:
With this remote control you can operate not only this TV but also the main functions of your VCR or DVD.
Switch on the device you want to operate and next press this button repeatedly to select the VCR, TV or
DVD. A green light will be momentarily lit to indicate the chosen function.
!¡ Selecting channels: Press this button to select the next or previous broadcast channel.
!™ Muting the Sound: Press this button to mute TV sound. Press again to restore the sound.
!£ Adjusting TV volume: Press this button to adjust the volume of the TV.
!¢ Displaying the menu system: Press this button to display the menu on the TV screen. Press again to
remove the menu display from the TV screen.
!∞ Selecting TV mode: Press this button to switch off PIP, teletext or video input.
!§ Selecting Sound effect: Press this button repeatedly to change the sound effect.
!¶ Selecting Picture mode: Press this button repeatedly to change the picture mode.
!• Displaying on Screen information: Press this button to display all on-screen indications. Press again
to cancel.
!ª Swapping screens: Whilst you are in “PIP” mode, press this button to swap the two screens.
@º
VCR or DVD on/off: Press this button to switch your VCR or DVD on or off.
@¡
PIP (Picture in Picture): Press this button to watch another source in a small picture (PIP) within the
main TV picture. Press again to cancel. To select the source you want to watch, refer to the chapter “PIP
Input” on page 16.
1
Before the first time you want to control a DVD or VCR by using this remote control, you have to set
it up depending on the brand of the device to be used. For more details, refer to chapter “Remote
Control Configuration for VCR or DVD” on page 20.
Besides TV functions, all coloured buttons as well as green symbols are also used for
Teletext operation. For more details, please refer to “Teletext” section of this instruction manual.
1 To Temporarily Switch Off TV:
Press this button to temporarily switch off TV (the standby indicatoron
the TV lights up). Press again to switch on TV from standby mode.
2
3
4
5
6
7
8
9
!º
!¡
To save energy we recommend switching off completely when TV is not in use.
After 15 minutes without a signal and without any button being
pressed, the TV switches automatically into standby mode.
2 Selecting input source: Press this button repeatedly until the desired
input symbol of the source appears on the TV screen.
3 Selecting channels:
If Media Selector is switched to TV or VCR, press this button to select
channels.
For double-digit programme numbers, enter the second digit within 2.5
seconds.
4 a) If Media Selector is switched to TV:
Press this button to watch the last channel selected (the last channel
watched for at least 5 seconds).
b) If Media Selector is switched to VCR:
For Sony’s VCR double-digit programme numbers, e.g. 23, press -/- -
first and then the buttons 2 and 3.
5 This button only works in Teletext mode.
6 Selecting screen format: Press this button repeatedly to change the
format of the screen. For more details refer to chapter “Auto Format” on
page 14.
7 Selecting Teletext: Press this button to switch on teletext.
8 a) If Media Selector is switched to TV:
• When MENU is switched on, use these buttons to operate the menu
system. For details refer to “Introducing and Using the Menu System”
on page 9.
• When MENU is switched off, press OK to show a channel overview.
Then pressorto select the channel and then press again the OK
button to watch the selected channel.
b)If Media Selector is switched to VCR or DVD:
Using these buttons you can control the main functions of your VCR or
DVD.
EN
Overview
5
Overview of TV Buttons
Auto Start Up Button
S video Input jack
Press on the
mark on the
door flap to
reveal the
control panel.
Programme Up or
Down Buttons (Selects
TV channels)
Volume control
buttons
Selecting
Input
source
Video
Input jack
Audio
Input jacks
Standby
indicator
On/Off
switch
Headphones
jack
Inserting Batteries into the Remote Control
• Make sure you insert the supplied batteries using the correct polarities.
• Always remember to dispose of used batteries in an environmental friendly way.
• To avoid battery leakage and damage to the ramote, remove the batteries from the remote if
you are not going to use it for several days. If any liquid that leaks from the batteries touches
you, immediately wash it away with water.
Connecting the Aerial and VCR
Connecting cables are not supplied.
Connect the
supplied
Scart adaptor
as it is shown.
Set the Scart
adaptor
switch to
“IN”.
For more details of VCR connection, please
refer to the section “Connecting Optional
Equipment” of this instruction manual.
VCR
Overview-Installation
6
Switching On the TV and Automatically Tuning
The first time you switch on your TV, a sequence of menu screens appear on the TV
enabling you to: 1) adjust the picture slant, 2) search and store all available channels
(TV Broadcast) and 3) change the order in which the channels (TV Broadcast) appear on
the screen.
However, if you need to change any of these settings at a later date, you can do that by
selecting the appropriate option in the (Set Up menu) or by pressing the Auto Start Up
Button on the TV set.
1 Connect the TV plug to the mains socket (220-240V AC,
50Hz)
Do not connect the power cord until you have
completed making all other connections; otherwise a
minimum leakage current might flow through the
aerial and other terminals to ground.
The first time that the TV set is connected, it is usually
turned on. If the TV is off, press the on/off button on
the TV set to turn on the TV.
The first time you switch on the TV, a menu screen
displays automatically on the TV.
2 Because of the earth’s magnetism, the picture might slant.
The Picture Rotation menu allows you to correct the
picture slant if it is necessary.
a) If it is not necessary, pressorto select Not
necessary and press OK.
b) If it is necessary, pressorto select Adjust now,
then press OK and correct any slant of the picture
between –5 and +5 by pressingor. Finally press
OK to store.
3 The Auto Tuning menu appears on the screen. Press the
OK button to select Yes.
If picture slants, please
adjust picture rotation
Not necessary
Adjust now
Do you want to start
automatic tuning?
Yes
No
EN
OK
OK
OK
OK
continued...
First Time Operation
7
4The TV starts to automatically search and store all
available broadcast channels for you.
This procedure could take some minutes. Please be
patient and do not press any buttons, otherwise the
automatic tuning will not be completed.
If no channels were found during the auto tuning
process then a new menu appears automatically on
the screen asking you to connect the aerial. Please
connect the aerial (see page 6) and press OK. The
auto tuning process will start again.
Auto Tuning
Programme: 01
Searching...
No channel found
Please connect aerial
Confirm
OK
OK
5After all available channels are captured and stored,
the Programme Sorting menu appears automaticallyon the screen enabling you to change the order in
which the channels appear on the screen.
a) If you wish to keep the broadcast channels in the
tuned order, go to step 6.
b) If you wish to store the channels in a different order:
1 Press theorbutton to select the programme
number with the channel (TV Broadcast) you wish
to rearrange, then press thebutton.
2 Press theorbutton to select the new
programme number position for your selected
channel (TV Broadcast), then press .
3 Repeat steps b)1 and b)2 if you wish to change
the order of the other channels.
6 Press the MENU button to remove the menu from the