4-206-161-31(1)
R
FD Trinitron
Colour Television
Instruction Manual
KV-28LS35U
KV-32LS35U
© 2001 by Sony Corporation
GB
NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM
A moulded plug complying with BS1363 is fitted to this equipment for your safety and
convenience.
Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or
BSI to BS 1362 (i.e. marked with 2 or @) must be used.
When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the
circuit should be protected by a 5 AMP FUSE at the distribution board.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse
cover after you change the fuse. Never use the plug without the fuse cover. If you should lose
the fuse cover, please contact your nearest Sony service centre.
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and replace the fuse.
• IMPORTANT
If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and
an appropriate plug fitted in accordance with the following instructions:
The wires in this mains lead are coloured in accordance with the following code:
Blue Neutral
Brown Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the
letter N or coloured black. The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red. Do not connect either wire to the
earth terminal in the plug which is marked by the letter E or by the safety earth symbol
or coloured green or green and yellow.
WARNING
• To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket
outlet. This plug cannot be used and should be destroyed.
• To prevent fire or shock hazard, do not expose the unit to rain or moisture.
• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing
to qualified personnel only.
2
Introduction
Thank you for choosing this Sony FD Trinitron Colour Television.
Before operating the TV, please read this manual thoroughly and retain it for future
reference.
• Symbols used in the manual:
• Informs you of possible hazards.
• Important information
• Information on a feature.
•1,2... Sequence of instructions.
• Shaded buttons on the remote control
OK
show you the buttons you have to press
to follow the sequence of the
instructions.
• Informs you of the result of instructions.
Table of Contents
Notice for Customers in the United Kingdom....................................................................................2
Introduction.............................................................................................................................................. 3
Safety Information................................................................................................................................... 4
Overview
Overview of Remote Control Buttons .................................................................................................. 5
Overview of TV Buttons ........................................................................................................................6
Installation
Inserting Batteries into the Remote Control ........................................................................................ 6
Connecting the Aerial and VCR ...........................................................................................................6
First Time Operation
Switching On the TV and Automatically Tuning ..............................................................................7
Menu system
Introducing and Using the Menu System............................................................................................9
Menu Guide:
Picture Adjustment .............................................................................................................................9
Sound Adjustment............................................................................................................................. 10
Sleep Timer.........................................................................................................................................11
Language ............................................................................................................................................11
Auto Tuning ....................................................................................................................................... 11
Programme Sorting ........................................................................................................................... 12
Programme Labels............................................................................................................................. 12
AV Preset ............................................................................................................................................12
Manual Programme Preset............................................................................................................... 13
Auto Format ....................................................................................................................................... 15
Noise Reduction................................................................................................................................. 15
AV2 Output ........................................................................................................................................ 16
RGB Centring ..................................................................................................................................... 16
Picture Rotation .................................................................................................................................16
Teletext............................................................................................................................................... 17
Additional Information
Connecting Optional Equipment ........................................................................................................ 18
Using Optional Equipment .................................................................................................................. 19
Remote Control Configuration for VCR/DVD.................................................................................20
Specifications.......................................................................................................................................... 21
Troubleshooting..................................................................................................................................... 22
Television Channel Guide for United Kingdom............................................................................... 23
Table of Contents
GB
3
Safety Information
This set is to operate on a 220240V AC supply only. Take care
not to connect too many
appliances to the same power
socket as this could result in fire
or electric shock.
Do not open the cabinet and the rear
cover of the TV. Refer to qualified
service personnel only.
Do not cover the ventilation
openings of the TV For
ventilation, leave a space of at
least 10cm all around the set.
For environmental and safety
reasons, it is recommended that
the TV set is not left in standby
mode when not in use. Disconnect
from the mains.
For your own safety, do not touch
any part of the TV, power lead or
aerial lead during lightning
storms.
Never place the TV in hot, humid
or excessively dusty places. Do
not install the TV where it may be
exposed to mechanical vibrations.
Never push objects of any kind into
the set as this could result in a fire
or electric shock. Never spill liquid
of any kind on the set. If any liquid
or solid object does fall through, do
not operate the TV. Have it checked
immediately by qualified
personnel.
To prevent fire or shock
hazard, do not expose the TV
to rain or moisture.
To prevent fire, keep inflammable
objects or naked lights (eg
candles) away from the TV.
Clean the TV with a soft, lightly
dampened cloth. Do not use
benzine, thinner or any other
chemicals to clean the TV. Do not
scratch the TV screen. As a safety
precaution, unplug the TV before
cleaning it.
Place the TV on a secure stable
stand. Do not allow children to
climb on to it. Do not place the TV
on its side or face up.
4
Safety Information
Pull out the power lead by the
plug. Do not pull on the power
lead itself.
Unplug the power lead before
moving the TV. Avoid uneven
surfaces, quick steps or excessive
force. If the set has been dropped
or damaged, have it checked
immediately by qualified service
personnel.
Take care not to place heavy
objects on the power lead as this
could result in damage.
We recommend you wind any
excess lead around the holders
provided on the rear of the TV.
Do not cover the ventilation
openings of the TV with items
such as curtains or newspapers
etc.
Overview of Remote Control Buttons
VCR or DVD on/off
Press to switch your VCR or DVD on or
off.
Selecting channels
If Media Selector is switched on TV or
VCR, press to select channels.
For double-digit programme numbers,
enter the second digit within 2.5 seconds.
Displaying on Screen information
Press to display all on-screen indications.
Press again to cancel.
Selecting Picture mode
Press repeatedly to change the
picture mode.
Selecting sound mode
Press repeatedly to change the
sound mode.
This button only works in Teletext mode.
Selecting TV mode
Press to switch off teletext or video input.
a) If Media Selector is switched
on TV:
• When MENU is switched on, use these
buttons to operate the menu system.
For details refer to “Introducing and
Using the Menu System” on page 9.
• When MENU is switched off, press OK
to show a channel overview. Then
press
and then press again the OK button to
watch the selected channel.
b) If Media Selector button is
switched on VCR or DVD:
Using these buttons you can control the
main functions of your VCR or DVD.
Displaying the menu system
Press to display the menu on the TV
screen. Press again to remove the menu
display from the TV screen.
Adjusting TV volume
Press to adjust the volume of the TV.
Muting the Sound
Press to mute TV sound. Press again to
restore the sound.
or to select the channel
Besides TV functions, all coloured buttons as well as green symbols are also used for
Teletext operation. For more details, please refer to “Teletext” section of this instruction
manual.
To Temporarily Switch Off TV
Press to temporarily switch off TV (the standby
indicator on TV lights up). Press again to switch on
TV from standby mode.
To save energy we recommend
switching off completely when TV is not
in use.
After 15 minutes without a signal
and without any button being
pressed, the TV switches
automatically into standby mode.
Selecting input source
Press repeatedly until the desired
input symbol of the source appears on
the TV screen.
a) If Media Selector button is
switched on TV:
Press to watch the last channel selected
(watched for at least 5 seconds).
b) If Media Selector button is
switched on VCR:
For Sony’s VCR double-digit
programme numbers, e.g. 23, press
-/- - first and then the buttons 2
and 3.
Selecting Screen format
Press repeatedly to change the
format of the screen. For more
details, refer to chapter “Auto
Format” on page 15.
Selecting Teletext
Press to switch on teletext.
Recording button
If Media Selector is switched on VCR,
press this button to record
programmes.
Media Selector
With this remote control you can
operate not only this TV but also the
main functions of your VCR or DVD.
Switch on the device you want to
operate and next press this button
repeatedly to select the VCR, TV or
DVD. A green light will be lit
momentarily.
An initial set up is required to
synchronise this remote control to
your VCR or DVD. It will depend on the
Brand of those products. For more
details, refer to chapter “Remote
Control Configuration for VCR or
DVD” on page 20.
Selecting channels
Press to select the next or previous
channel.
Overview
GB
5
Overview of TV Buttons
Auto Start Up Button
S video Input jack
Press on the
mark on the
door flap to
reveal the
control panel
Headphones
Selecting
Input
source
Video
Input jack
jack
Programme Up or
Down Buttons (Selects
TV channels)
Volume control
buttons
Audio
Input jacks
Standby
indicator
On/Off switch
Inserting Batteries into the Remote Control
Make sure you insert the supplied batteries using the correct polarities.
Always remember to dispose of used batteries in an environmental friendly way.
Connecting the Aerial and VCR
Connecting cables are not supplied.
or
OUT IN
VCR
For more details of VCR connection, please
refer to the section “Connecting Optional
Equipment” of this instruction manual.
Overview-Installation
6
Scart lead is optional.
Switching On the TV and Automatically Tuning
The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you to: 1) choose the language of the menu screen, 2) adjust the picture slant 3) search
and store all available broadcast channels and 4) change the order in which the broadcast
channels appear on the screen.
However, if you need to change any of these settings at a later date, you can do that by
selecting the appropriate option in the (Set Up menu) or by pressing the Auto Start Up
Button on the TV set.
1 Connect the TV plug to the mains socket (220-240V AC,
50Hz)
The first time the TV set is connected, it is usually turned
on. If the TV is off, press the on/off button on the TV
set to turn on the TV.
The first time you switch on the TV, a Language menu
displays automatically on the TV screen.
GB
2 Press the or button on the remote control to select
the language, then press the OK button to confirm your
selection. From now on all the menus will appear in the
selected language.
3 Because of the earth’s magnetism, the picture might slant.
The Picture Rotation menu allows you to correct the
picture slants if it is necessary.
a) If it is not necessary, press or to select Not
necessary and press OK.
b) If it is necessary, press or to select Adjust now,
then press OK and correct any slant of the picture
between –5 and +5 by pressing or . Finally press
OK to store.
Language
i
4
Svenska
Norsk
English
Nederlands
Français
Italiano
$
i
Select Language:
If picture slants, please
adjust picture rotation
Not necessary
Adjust now
First Time Operation
OK
OK
OK
OK
continued...
7
4 The Auto Tuning menu appears on the screen. Press the
OK button to select Yes.
Do you want to start
automatic tuning?
Yes
No
OK
OK
5The TV starts to automatically search and store all
available broadcast channels for you.
This procedure could take some minutes. Please be
patient and do not press any buttons, otherwise the
automatic tuning will not be completed.
If no channels were found during the auto tuning
process then a new menu appears automatically on
the screen asking you to connect the aerial. Please
connect the aerial (see page 6) and press OK. The
auto tuning process will start again.
6 After all available broadcast channels are captured
and stored, the Programme Sorting menu appears
automatically on the screen enabling you to change
the order in which the broadcast channels appear on
the screen.
a) If you wish to keep the broadcast channels in the
tuned order, go to step 7.
b) If you wish to store the broadcast channels in a
different order:
1 Press the or button to select the programme
number with the broadcast channel you wish
to rearrange, then press the button.
2 Press the or button to select the new
programme number position for your selected
broadcast channel, then press .
3 Repeat steps b)1 and b)2 if you wish to change
the order of the other broadcast channels.
Auto Tuning
Programme: 01
Channel: C21
Searching...
No channel found
Please connect aerial
Confirm
OK
Programme Sorting
Programme:
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58
Select channel:
Exit:
MENU
Programme Sorting
Programme:
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58 05 C27
Select new position:
Exit: MENU
OK
OK
OK
P
)
0
·
#
3
OK
p
OK
7 Press the MENU button to remove the menu from the
screen.
Your TV is now ready for use
First Time Operation
8
MENU
Introducing and Using the Menu System
Your TV uses an on-screen menu system to guide you through the operations. Use the
following buttons on the Remote Control to operate the menu system:
1 Press the MENU button to switch the first level menu on.
2 • To highlight the desired menu or option, press or .
• To enter to the selected menu or option, press .
• To return to the last menu or option, press .
• To alter settings of your selected option, press //or.
• To confirm and store your selection, press OK.
3 Press the MENU button to remove the menu from the screen.
Menu Guide
Level 1 Level 2 Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
OK
Reset
PICTURE ADJUSTMENT
The “Picture Adjustment” menu allows you to
alter the picture adjustments.
To do this: after selecting the item you want to
OK
alter press , then press repeatedly / /
or to adjust it and finally press OK to
store the new adjustment.
This menu also allows you to customise the
picture mode based on the programme you are
watching:
Personal (for individual settings).
Live (for live broadcast programmes, DVD
and Digital Set Top Box receivers).
Movie (for films).
MENU
OK
MENU
GB
• Brightness, Colour and Sharpness can only be altered if “Personal” mode is selected.
• Hue is only available for NTSC colour signal (e.g: USA video tapes).
• Select Reset and press OK to reset the picture to the factory preset levels.
continued...
Menu System
9
Level 1 Level 2 Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Sound Adjustment
Mode: Personal
Treble
Bass
Balance
Reset
Dual Sound: Mono
Detail Adjustment
OK
Sound Adjustment
Mode: Personal
Treble
Bass
Balance
Reset
Dual Sound: Mono
OK
Detail Adjustment
This menu also contains two submenus as following:
Mode Personal (for individual settings)
Rock
Pop
Jazz
*
Detail Adjustment Dolby
Virtual: Off: Normal.
Pro Logic surround.
Auto volume: Off: Volume level changes according
to the broadcast signal.
TV Speakers: Off: Sound from external amplifier
connected to the audio outputs on
the rear of the TV set.
SOUND ADJUSTMENT
The “Sound Adjustment” menu allows you to
alter the sound adjustments.
To do this: after selecting the item you want to
alter, press . then press repeatedly /
/ or to adjust it and finally press OK
to store the new adjustment.
OK
On: Simulates the sound effect of Dolby
On: Volume level of the channels will
stay the same, independent of the
broadcast signal (e.g. in the case of
advertisements).
On: Sound from the TV set.
• Treble and Bass can only be altered if “Personal” mode is selected.
• Select Reset and press OK to reset the sound to the factory preset levels.
• In case of a bilingual broadcast select Dual Sound and set A for sound channel 1, B for sound channel
2 or Mono for mono channel if available. For a stereo broadcast you can choose Stereo or Mono.
• If you are listening to the TV through headphones, “Dolby Virtual” option will automatically be
switched to “Off”.
• If you switch “Dolby Virtual” to “On”, the “Auto volume” option will automatically be switched to
“Off” and vice versa.
*
This TV has been designed to create the “Dolby Surround” sound effect by simulating the sound
of four speakers with two speakers, when the broadcast audio signal is Dolby Surround encoded.
The sound effect can also be improved by connecting a suitable external amplifier (for details refer
to “Connecting to external audio Equipment” on page 19).
*
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D
symbol are trademarks of Dolby Laboratories.
continued...
Menu System
10
Level 1 Level 2 Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
SLEEP TIMER
The “Sleep Timer” option in the “Timer” menu
allows you to select a time period for the TV to
switch itself automatically into the standby
mode.
Timer
Sleep Timer: Off
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Timer
Sleep Timer: Off
To do this: after selecting the option press ,
then press or to set the time period delay
(max. of 4 hours) and finally press OK to store.
• While watching the TV, you can press the
OK
OK
button on the remote control to display the
time remaining.
• One minute before the TV switches itself into
standby mode, the time remaining is displayed on
the TV screen automatically.
LANGUAGE
The “Language” option in the “Set Up” menu
allows you to select the language that the
menus are displayed in.
OK
To do this: after selecting the option, press
GB
and then proceed in the same way as in the step
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
OK
Detail Set Up
2 of the section “Switching On the TV and Automatically Tuning”.
OK
AUTO TUNING
The “Auto Tuning” option in the “Set Up”
menu allows you to automatically search for
and store all available TV broadcast channels.
OK
To do this: after selecting the option, press
and then proceed in the same way as in TV
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
OK
Detail Set Up
steps 4 and 5 of the section “Switching On the
TV and Automatically Tuning”.
OK
continued...
Menu System
11
Level 1 Level 2 Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
OK
Detail Set Up
PROGRAMME SORTING
The “Programme Sorting” option in the “Set
Up” menu allows you to change the order in
which the broadcast channels appear on the
screen.
To do this: after selecting the option, press
and then proceed in the same way as in step 6 b)
of the section “Switching On the TV and
Automatically Tuning”.
OK
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
PROGRAMME LABELS
The “Programme Labels” option in the “Set
Up” menu allows you to name a broadcast
channel using up to five characters (letters or
OK
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
OK
Detail Set Up
numbers).
To do this:
1 After selecting the option, press , then
press or to select the programme
number with the broadcast channel you wish
to name.
OK
2 Press . With the first element of the Label
column highlighted, press or to select
a letter or number (select “-“ for a blank), then
press to confirm this character. Select the
other four characters in the same way. Finally
press OK to store.
AV PRESET
The “AV Preset” option in the “Set Up” menu
allows you to designate a name to the external
equipment you have connected to the sockets of
OK
this TV.
To do this:
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
OK
Detail Set Up
1 After selecting the option, press , then
press or to select the input source you
wish to name (AV1 and AV2 are for the rear
Scarts and AV3 for side connectors). Then
press .
OK
2 In the label column automatically appears a
label:
a) If you want to use one of the 6 predefined
labels (CABLE, GAME, CAM, DVD,
VIDEO or SAT), press or to select
the desired label and finally press OK to
store.
b) If you want to set a different label, select
Edit and press . Then with the first
element highlighted, press or to
select a letter, number or “-“ for a blank,
then press to confirm this character.
Select the other four characters in the same
way and finally press OK to store.
12
Menu System
continued...
Level 1 Level 2 Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
OK
Detail Set Up
MANUAL PROGRAMME PRESET
The “Manual Programme Preset” option in the
“Set Up” menu allows you to:
a) Preset broadcast channels or a video input
source one by one to the programme order of
your choice. To do this:
1 After selecting the ”Manual Programme
Preset” option, press then with
Programme option highlighted press .
Press or to select on which
OK
programme number you want to preset the
broadcast channel (for VCR, select
programme number “0”). Then press .
2 After selecting the Channel option, press .
Then, press the number buttons to enter
directly the channel number of the TV
Broadcast or the channel of the VCR signal. If
you do not know the channel number,
press or to search for it. When you
tune the desired channel, press OK twice to
store.
Repeat all the above steps to tune and store more
channels.
b) Label a channel using up to five characters.
To do this: Highlighting the Programme
option, press the PROG +/- button to select
the programme number with the broadcast
channel you wish to name. When the TV
broadcast you want to name appears on the
screen, select the Label option and press .
Next press or to select a letter, number
or “-“ for a blank. Press to confirm this
character. Select the other four characters in
the same way. After selecting all the
characters, press OK twice to store.
GB
continued...
Menu System
13
Level 1 Level 2 Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
OK
Detail Set Up
c)Normally the automatic fine tuning (AFT) is
operating, however you can manually fine
tune the TV to obtain a better picture
if the picture is distorted.
To do this: while watching the channel (TV
Broadcast) you wish to fine tune, select the
AFT option and press . Next press
or to adjust the fine tuning between -15
and +15. Finally press OK twice to store.
OK
d) Skip any unwanted programme numbers
when they are selected with the PROG +/buttons.
To do this: Highlighting the Programme
option, press the PROG +/- button to select
the programme number you want to skip.
When the programme you want to skip
appears on the screen, select the Skip option
and press . Next press or to select
Yes. Finally press OK twice to confirm and
store.
To cancel this function afterwards, select “No”
instead of “Yes” in the step above.
14
Menu System
continued...
Level 1 Level 2 Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Detail Set Up
Auto Format
Noise Reduction:
AV2 Output:
RGB Centring:
Picture Rotation:
OK
Even if you have selected “On” or “Off” in the “Auto Format” option, you can always
modify the format of the screen by pressing repeatedly on the
remote control to select one of the following formats:
14:9: Compromise between 4:3 and 16:9 picture size.
Zoom: Widescreen format for letterbox movies.
AUTO FORMAT
The “Auto Format” option in the “Detail Set
Up” menu allows you to automatically change
the aspect ratio of the screen.
To do this: after selecting the option, press .
Then press or to select On (if you wish
On
Auto
the TV set to automatically switch the screen
TV
0
format according to the broadcast signal) or Off
0
(if you wish to keep your preference). Finally
OK
press OK to store.
14:9
Wide: For 16:9 broadcast.
Smart: Imitation of wide screen effect for 4:3 broadcast.
4:3: Conventional 4:3 picture size, full picture information.
In “Smart”, “Zoom” and “14:9” modes, parts of the top and
bottom of the screen are cut off. Press or to adjust the
position of the image on the screen (e.g. to read subtitles).
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Detail Set Up
Auto Format
Noise Reduction:
AV2 Output:
RGB Centring:
Picture Rotation:
OK
NOISE REDUCTION
The “Noise Reduction” option in the “Detail Set
Up” menu allows you to automatically reduce
the picture noise visible in the broadcast signal.
To do this: after selecting the option, press .
On
Auto
Then press or to select Auto. Finally
TV
0
0
press OK to confirm and store.
OK
To cancel this function afterwards, select “Off”
instead of “Auto” in the step above.
Zoom
GB
Wide
Smart
4:3
continued...
Menu System
15
Level 1 Level 2 Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
Detail Set Up
Auto Format
Noise Reduction:
AV2 Output:
RGB Centring:
Picture Rotation:
OK
If you select “AUTO”, the output signal will always be the same one that is displayed on
the screen.
If you have connected a decoder to the Scart :2/q or to a VCR connected to this Scart,
please remember to change back the “AV2 Output” to “AUTO” or “TV” for correct
unscrambling.
AV2 OUTPUT
The “AV2 Output” option in the “Detail Set Up”
menu allows you to select the source to be
output from the Scart connector :2/q. You
can record from this Scart any signal coming
from the TV or from external equipment
connected to the Scart connector :1/ or
On
Auto
TV
side connectors 3 and 3.
0
0
OK
If your VCR supports Smartlink, this
procedure is not necessary.
To do this: after selecting the option, press .
Then press or to select the desired
output signal: TV, AV1, AV3, YC3 or AUTO.
16
Menu System
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
RGB CENTRING
When connecting an RGB source, such as a
“PlayStation”, you may need to readjust the
horizontal position of the picture. In that case,
OK
Detail Set Up
Auto Format
Noise Reduction:
AV2 Output:
RGB Centring:
Picture Rotation:
OK
you can readjust it through the “RGB Centring”
option in the “Detail Set Up”.
On
Auto
To do this: while watching an RGB source select
TV
0
0
the “RGB Centring” option and press . Then
press or to adjust the centre of the
OK
picture between –10 and +10. Finally press OK
to confirm and store.
PICTURE ROTATION
Because of the earth’s magnetism, the picture
might slant. In this case, you can correct the
OK
Detail Set Up
Auto Format
Noise Reduction:
AV2 Output:
RGB Centring:
Picture Rotation:
OK
picture slant by using the option “Picture
Rotation” in the “Detail Set Up” menu.
To do this: after selecting the option, press .
On
Auto
Then press or to correct any slant of the
TV
0
0
picture between -5 and +5 and finally press OK
to store.
OK
Teletext
Teletext is an information service transmitted by most TV stations. The index page of the
teletext service (usually page 100) gives you information on how to use the service. To
operate teletext, use the remote control buttons as indicated below.
Make sure to use a broadcast channel with a strong signal, otherwise teletext errors
may occur.
To Switch On Teletext :
After selecting the TV channel which carries the teletext service you wish
to view, press .
To Select a Teletext page:
Input 3 digits for the page number, using the numbered buttons.
• If you have made a mistake, retype the correct page number.
• If the counter on the screen continues searching, it is because this page is not available. In that case,
input another page number
To access the next or preceding page:
Press PROG + ( ) or PROG - ().
TELETEXT
TELETEXT
TELETEXT
TELETEXT
TELETEXT
TELETEXT
TELETEXT
TELETEXT
Index
Index
Index
Index
Index
Index
Index
Index
Programme
Programme
Programme
Programme
Programme
Programme
Programme
Programme
News
News
News
News
News
News
News
News
Sport
Sport
Sport
Sport
Sport
Sport
Sport
Sport
Weather
Weather
Weather
Weather
Weather
Weather
Weather
Weather
25
25
25
25
25
25
25
25
153
153
153
153
153
153
153
153
101
101
101
101
101
101
101
101
98
98
98
98
98
98
98
98
To superimpose teletext on to the TV:
Whilst you are viewing teletext, press . Press it again to cancel teletext mode.
To freeze a teletext page:
Some teletext pages have sub-pages which follow on automatically. To stop them, press
/ . Press it again to cancel the freeze.
To reveal concealed information (e.g: answer to a quiz):
Press / . Press it again to conceal the information.
To Switch Off Teletext:
Press .
Fastext
Fastext service lets you access pages with one button push.
While you are in Teletext mode and Fastext is broadcast, a colour coded menu appears at
the bottom of the teletext page. Press the colour button (red, green, yellow or blue) to access
the corresponding page.
GB
Teletext
17
Connecting Optional Equipment
“PlayStation”*
Using the following instructions you can connect a wide range of optional equipment to
your TV set. (Connecting cables are not supplied).
D
F
E
VCR
VCR
VCRDVD
Decoder
S VHS/Hi8
DVC
camcorder
A
C
8mm/Hi8/
DVC
camcorder
B
VCRDVD
2
When you connect the headphones,
the TV speakers will automatically
be muted.
1
Decoder
* “PlayStation” is a product of Sony
Computer Entertainment, Inc.
* “PlayStation” is a trademark of Sony
Computer Entertainment, Inc.
Hi-fi
To avoid picture distorsion, do not connect external equipment to connectors A and B at
the same time.
Connecting a VCR:
To connect a VCR, please refer to the section “Connecting the aerial and VCR” of this instruction
manual. We recommend you connect your VCR using a scart lead. If you do not have a scart
lead, tune in the VCR test signal to the TV programme number “0” by using the “Manual
Programme Preset” option. (for details of how to manually programme these presets, see page
13, step a).
Refer to your VCR instruction manual to find out how to find the output channel of your VCR.
Connecting a VCR that supports Smartlink:
Smartlink is a direct link between the TV set and the VCR. For more information on
Smartlink, please refer to the instruction manual of your VCR.
If you use a VCR that supports Smartlink, please connect the VCR by using a Scart lead to
the Scart
:2/q F.
18
continued...
Additional Information
Connecting to external Audio Equipment:
Left Hi-Fi
Speaker
Plug in your Hi-Fi equipment to the audio output sockets E if you wish to amplify the audio
output from TV. Next, using the menu system, select the “Sound Adjustment” menu. Enter the
“Detail Adjustment” option and set “TV Speakers” to “Off”.
The audio level of the external speakers can be modified by pressing the volume buttons
on the remote control. Also treble and bass settings can be modified through the “Sound
Adjustment” menu.
To enjoy “Dolby Virtual” sound effect through your
Hi-Fi equipment:
Place the speakers of your equipment in front of your
sitting place and besides the TV set but keep a distance of
50 cm from each speaker to the TV set.
Then by using the menu system, select the menu “Sound
Adjustment”. Next select “Detail Adjustment” and set
“Dolby Virtual” to “On”.
~50°
Right Hi-Fi
Speaker
Using Optional Equipment
Your sitting position
1 Connect your equipment to the designated TV socket, as indicated in the previous page.
2 Switch on the connected equipment.
3 To watch the picture of the connected equipment, press the button repeatedly until the
correct input symbol appears on the screen.
Symbol Input Signals
1 • Audio / video input signal through the Scart connector D
• RGB input signal through the Scart connector D. This symbol appears only
if a RGB source has been connected.
2 • Audio / video input signal through the Scart connector F.
S
2 • S Video input signal through the Scart connector F.
3 • Video input signal through the phono socket B and Audio input signal
through C.
S
3 • S Video Input signal through the front S Video input jack A and Audio
signal through C.
4 Press button on the remote control to return to the normal TV picture.
For Mono Equipment
Connect the phono plug to the L/G/S/I socket on the front of the TV and select 3 or 3
input signal using the instructions above. Finally, refer to the “Sound Adjustment” section of
this manual and select “Dual Sound” “A” on the sound menu screen.
S
GB
Additional Information
19
Remote Control Configuration for VCR/DVD
This remote control is set by default to operate basic functions of this Sony TV, Sony DVD and
most of Sony VCR when batteries are initially installed. To control other VCR and DVD major
brands and some Sony VCR models, please complete the following steps:
•Before you start, look up the 3 digit code for your brand of DVD or VCR from the list
below. On those brands that have more than one code, enter the first code number.
•Sony will endeavour to update the software according to market changes.
Therefore, please refer to code table included with the remote control for
latest code set.
1 Press the Media Selector button on the remote control repeatedly until the
required VCR or DVD green light is lit.
If Media Selector is on TV position, code numbers will not be stored.
2 Before the green light goes out, press and hold the yellow button for
approximately 6 seconds until the green light starts flashing.
3 Whilst the green light is flashing, enter all three digits of the code for your
brand using the number buttons on the remote control.
If your selected code is entered correctly, all three green lights will be lit
momentarily.
4 Turn on your brand VCR or DVD and check that the main functions work.
• If your device is not working or some of the functions do not work
please check you entered the correct code set or try the next code listed
against the brand.
• Your brand codes may be lost if weak batteries are not replaced within
a few minutes. To reset your brand DVD or VCR please repeat the
above steps. A small label is added inside the battery door to allow you
to record your brand codes.
• Not all brands are covered and not all models of every brand may be covered.
1
2
3
VCR Brand List DVD Brand List
Brand Code Brand Code
SONY (VHS) 301, 302, 303, 308, 309 SONY 001
SONY (BETA) 303, 307, 310 AIWA 021
SONY (DV) 304, 305, 306 DENON 018, 027, 020, 002
AIWA 325, 331, 351 GRUNDIG 009, 028, 023, 024, 016, 003
AKAI 326, 329, 330 HITACHI 025, 026, 015, 004
DAEWOO 342, 343 JVC 006, 017
GRUNDIG 358, 355, 360, 361, 320, 351 KENWOOD 008
HITACHI 327, 333, 334 LG 015, 014
JVC 314, 315, 322, 344, 352, 353, LOEWE 009, 028, 023, 024, 016, 003
LG 332, 338 ONKYO 022
LOEWE 358, 355, 360, 361, 320, 351 PANASONIC 018, 027, 020, 002
MATSUI 356, 357 PHILIPS 009, 028, 023, 024, 016, 003
ORION 328 PIONEER 004
PANASONIC 321, 323 SAMSUNG 011, 014
PHILIPS 311, 312, 313, 316, 317, 318, SANYO 007
SAMSUNG 339, 340, 341, 345 THOMSON 012
SANYO 335, 336 TOSHIBA 003
SHARP 324 YAMAHA 018, 027, 020, 002
THOMSON 319, 350
TOSHIBA 337
20
Additional Information
354, 348, 349 MATSUI 013, 016
358, 359 SHARP 019, 027
Specifications
TV system:
I
Colour system:
PAL,
SECAM, NTSC 3.58, 4.43 (only Video In)
Channel Coverage:
I: UHF B21-B69
Picture Tube:
Flat Display FD Trinitron WIDE
• KV-28LS35U: 28” (approx. 71 cm.
measured diagonally)
• KV-32LS35U: 32” (approx. 82 cm.
measured diagonally)
Rear Terminals
:1/ 21-pin scart connector
(CENELEC standard)
including audio/video
input, RGB input, TV
audio/video output.
:2/q 21-pin Scart connector
(SMARTLINK)
Side Terminals
q3 S Video input – 4 pin DIN
…3 video input – phono jack
3 audio input – phono jacks
headphones jack
(CENELEC standard)
including audio / video
input, S video input,
selectable audio / video
output and Smartlink
interface.
audio outputs (Left/
Right) - phono jacks
Sound Output:
2 x 14 W (music power)
2 x 7 W (RMS)
Woofer:
20 W (music power)
10 W (RMS)
Power Consumption:
KV-28LS35U: 90 W
KV-32LS35U: 88 W
Standby Power Consumption:
0.54 W
Dimensions (w x h x d) :
KV-28LS35U: Approx. 806 x 497 x 540 mm.
KV-32LS35U: Approx. 891 x 564 x 584 mm.
Weight:
KV-28LS35U: 43 Kg.
KV-32LS35U: 60.5 Kg.
Accessories supplied:
1 Remote Control (RM-932)
2 Batteries (IEC designated)
Other features:
• Teletext, Fastext, TOPtext
• Sleep Timer
• Smartlink (direct link between your TV set
and a compatible VCR. For more
information on Smartlink, please refer to
the Instruction Manual of your VCR).
• Dolby Virtual
• Auto Format
GB
Design and specifications are subject to change without notice.
Ecological Paper- Totally Chlorine Free
Additional Information
21
Troubleshooting
Here are some simple solutions to the problems which may affect the picture and sound.
Problem
No picture (screen is dark) and no
sound.
Poor or no picture (screen is dark),
but good sound.
No picture or no menu information
from equipment connected to the
Scart connector.
Good picture, no sound.
No colour on colour programmes.
Distorted picture when changing
programmes or selecting teletext.
Picture slanted
Noisy picture when viewing a TV
channel.
No unscrambling or unstable picture
whilst viewing a scrambling channel
with a decoder connected through
the Scart connector
Remote control does not function.
The standby indicator on the TV
flashes.
If you continue to experience problems, have your TV serviced by qualified personnel.
Never open the casing yourself.
Additional Information
22
:2/q.
Solution
•Check the aerial connection.
• Plug the TV in and press the button on the front of
the TV.
•If the standby indicator is on, press TV button
on the remote control.
•Using the menu system, select the “Picture
Adjustment” menu and select “Reset” to return to the
factory settings.
•Check that the optional equipment is on and press the
button repeatedly on the remote control until the
correct input symbol is displayed on the screen.
• Press the +/- button on the remote control.
• Check that “TV Speakers” is “On” on the “Sound
Adjustment” menu.
• Check that headphones are not connected.
• Using the menu system, select the “Picture
Adjustment” menu and select “Reset” to return to
factory settings.
• Turn off any equipment connected to the Scart
connector on the rear of the TV.
• Using the menu system, select the “Picture Rotation”
option in the “Detail Set Up” menu to correct the
picture slant.
• Using the menu system, select the “Manual
Programme Preset” menu and adjust Fine Tuning
(AFT) to obtain better picture reception.
• Using the menu system, select the “Noise Reduction”
option in the “Detail Set Up” menu and select
“Auto” to reduce the noise in the picture.
• Using the menu system, select the “Set Up” menu.
Then enter to “Detail Set Up” option and set “AV2
Output” to “TV”.
• Check that the Media Selector on the remote control is
set according to the device you are using (VCR, TV or
DVD).
• If the remote control does not operate the VCR or DVD
even when the Media Selector has been set correctly.
Enter the necessary code set as explained on “Remote
Control Configuration for VCR/DVD” chapter of this
instruction manual.
• Replace the batteries.
• Contact your nearest Sony service centre.
Television Channel Number Guide for United Kingdom
Only the main transmitters are listed. Information regarding the regional sub-relay
channel numbers can be obtained by contacting The BBC Engineering Information Dept.,
Telephone Number 020 7852 5040.
GB
Additional Information
23
Sony España, S.A.
Printed in Spain
Ecological Paper - Totally Chlorine Free
Loading...