Sony KV-21LT1U, KV-14LT1U User Manual

Download

Page 1

4-206-416-31(1)

FD Trinitron Colour Television

Instruction Manual

KV-21LT1U KV-14LT1U

Page 2

NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362 (i.e. marked with 2 or @) must be used. When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

How to replace the fuse

Open the fuse compartment with a blade screwdriver, and replace the fuse.

• IMPORTANT

If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and an appropriate plug fitted in accordance with the following instructions: The wires in this mains lead are coloured in accordance with the following code: Blue Neutral Brown Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not connect either wire to the earth terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green and yellow.

WARNING

• To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket outlet. This plug cannot be used and should be destroyed.

• To prevent fire or shock hazard, do not expose the unit to rain or moisture.

• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to qualified personnel only.

Page 3

Introduction

Thank you for choosing this Sony FD Trinitron Colour Television.

Before operating the TV, please read this manual thoroughly and retain it for future reference.

• Symbols used in the manual:

• Informs you of possible hazards.

• Important information

• Information on a feature.

•1,2... Sequence of instructions.

• Shaded buttons on the remote control show you the buttons you have to press to follow

the sequence of the instructions.

• Informs you of the result of instructions.

Table of Contents

Notice for Customers in the United Kingdom....................................................................................2

Introduction.............................................................................................................................................. 3

Safety Information................................................................................................................................... 4

Overview

Overview of Remote Control Buttons .................................................................................................. 5

Overview of TV Buttons ........................................................................................................................6

Installation

Inserting Batteries into the Remote Control ........................................................................................ 6

Connecting an Indoor Aerial (only for KV-14LT1U) .........................................................................7

Connecting an Outdoor Aerial and VCR ............................................................................................7

First Time Operation

Switching On the TV and Automatically Tuning ..............................................................................8

Menu system

Introducing and Using the Menu System..........................................................................................10

Menu Guide ........................................................................................................................................... 10

Teletext............................................................................................................................................... 16

Additional Information

Connecting Optional Equipment ........................................................................................................ 17

Using Optional Equipment .................................................................................................................. 17

Specifications.......................................................................................................................................... 18

Troubleshooting..................................................................................................................................... 19

Television Channel Number Guide for United Kingdom............................................................... 20

Table of Contents

Page 4

Safety Information

This set is to operate on a 220240V AC supply only. Take care not to connect too many appliances to the same power socket as this could result in ﬁre or electric shock.

Do not open the cabinet and the rear cover of the TV. Refer to qualiﬁed service personnel only.

Do not cover the ventilation openings of the TV For ventilation, leave a space of at least 10cm all around the set.

For environmental and safety reasons, it is recommended that the TV set is not left in standby mode when not in use. Disconnect from the mains.

For your own safety, do not touch any part of the TV, power lead or aerial lead during lightning storms.

Never place the TV in hot, humid or excessively dusty places. Do not install the TV where it may be exposed to mechanical vibrations.

Never push objects of any kind into the set as this could result in a ﬁre or electric shock. Never spill liquid of any kind on the set. If any liquid or solid object does fall through, do not operate the TV. Have it checked immediately by qualiﬁed personnel.

To prevent ﬁre or shock hazard, do not expose the TV to rain or moisture.

To prevent ﬁre, keep inﬂammable objects or naked lights (eg candles) away from the TV.

Clean the TV with a soft, lightly dampened cloth. Do not use benzine, thinner or any other chemicals to clean the TV. Do not scratch the TV screen. As a safety precaution, unplug the TV before cleaning it.

Place the TV on a secure stable stand. Do not allow children to climb on to it. Do not place the TV on its side or face up.

Safety Information

Pull out the power lead by the plug. Do not pull on the power lead itself.

Unplug the power lead before moving the TV. Avoid uneven surfaces, quick steps or excessive force. If the set has been dropped or damaged, have it checked immediately by qualiﬁed service personnel.

Take care not to place heavy objects on the power lead as this could result in damage. We recommend you wind any excess lead around the holders provided on the rear of the TV.

Do not cover the ventilation openings of the TV with items such as curtains or newspapers etc.

Page 5

Overview of Remote Control Buttons

Muting the Sound

Press to mute TV sound. press again to restore the sound.

Displaying on Screen information

Press to display all on-screen indications. Press again to cancel.

Selecting channels

Press to select channels.

For double-digit programme numbers, e.g. 23, press -/-- first, then the buttons 2 and 3.

If you enter an incorrect first digit, this should be corrected by entering another digit (0-9) and then selecting

-/-- button again to enter the

programme number of your choice.

Selecting TV mode

Press to switch off teletext or video input.

Selecting Teletext

Press to switch on teletext.

This button only works in Teletext mode. Function associated to this button does not work with this TV.

Selecting Picture mode

Press repeatedly to change the picture mode.

Adjusting TV volume

Press to adjust the volume of the TV.

This button only works in Teletext mode. Function associated to this button does not work with this TV.

Selecting channels

Press to select the next or previous channel.

To Temporarily Switch Off TV

Press to temporarily switch off TV (the standby indicator on TV lights up). Press again to switch on TV from standby mode.

To save energy we recommend switching off completely when TV is not in use.

After 15 minutes without a

signal and without any button being pressed, the TV switches automatically into standby

mode.

Selecting input source

Press repeatedly until the desired

input symbol of the source appears on the TV screen.

Back to the channel last watched

Press to watch the last channel

selected (watched for at least 5 seconds).

Displaying the menu system

PROGR

Press to display the menu on the TV screen. Press again to remove the menu display from the TV screen.

Menu selection

•When MENU is switched on:

887

Scroll Up Scroll Down Previous menu or selection Next menu or selection

OK confirms your selection

•When MENU is switched off: OK Shows a channel overview. Press or to select the

channel and then, press again the OK button to watch the selected channel.

Selecting Screen format

Press to view programmes in 16:9 mode. Press again to return to 4:3 mode.

Besides TV functions, all coloured buttons as well as green symbols are also used for Teletext operation. For more details, please refer to "“Teletext” section of this instruction manual.

Overview

Page 6

Overview of TV Buttons

Selecting Input source

Video Input jack

Press on the mark on the front of the TV to reveal the front connectors.

Audio Input jack

Headphone jack

Auto Start Up Button

Volume control buttons

Programme Up or Down Buttons (Select TV channels)

Standby indicator

On/Off switch

Inserting Batteries into the Remote Control

Make sure to insert the supplied batteries using the correct polarities. Always remember you dispose of used batteries in an environmental friendly way.

Overview-Installation

Page 7

Connecting an Indoor Aerial

Scart lead is optional.

(only for KV-14LT1U)

For a better reception we recommend you connect an external aerial. However, where an external aerial is not available and your local UHF signal is strong you can connect the supplied loop aerial as follows:

1 Insert the loop aerial into the opening on top of the set until it clicks.

2 Connect the aerial connector to the aerial socket on the rear of the set.

3 After turning on the TV, adjust the aerial for optimum

reception.

Connecting an Outdoor Aerial and VCR

For more details of VCR connection, please refer to the section “Connecting Optional

Equipment” of this instruction manual.

Connecting cables are not supplied

OUT IN

VCR

Installation

Page 8

Switching On the TV and Automatically Tuning

The first time you switch on your TV, a sequence of menu screen appear on the TV enabling you to: 1) choose the language of the menu screen, 2) search and store all available channels (TV Broadcast) and 3) change the order in which the channels (TV Broadcast) appear on the screen. However, if you need to change the language menu, change or repeat the tuning (e.g. when you move house) or rearrange again the order of the channels afterwards, you can do that by selecting the appropriate menu in the (Set Up). For more information, refer to the “Menu Guide” section of this instruction manual. You can also do that by pressing the Auto Start Up Button on the TV set.

1 Connect the TV plug to the mains socket (220-240V AC,

50Hz) The first time the TV set is connected, it is usually turned on. If the TV is off, press the on/off button on the TV set to turn on the TV. The first time you press this button, a Language menu displays automatically on the TV screen.

2 Press the or button on the remote control to select

the language, then press the OK button to confirm your selection. From now on all the menus will appear in the selected language.

3 The Auto Tuning menu appears on the screen. Press the

OK button to select Yes.

4 A new menu appears on the screen asking you to check

that the aerial is connected. Ensure the aerial is connected and then press the OK button to start the automatic tuning.

The TV starts to automatically search and store all

available channels (TV Broadcast) for you.

This procedure could take some minutes. Please be patient and do not press any buttons, otherwise the automatic tuning will not be completed.

First Time Operation

Language

English Español Français Italiano Magyar Nederlands

Select Language:

Do you want to start

automatic tuning?

Yes

Please confirm that aerial is connected

Confirm

Auto Tuning

Programme: 01 Channel: C21

Searching...

continued...

Page 9

5 After all available channels are captioned and stored,

Programme Sorting

Select channel: Exit:

Programme: 01 TVE 02 TVE2 03 TV3 04 C33 05 C27 06 C58

Programme Sorting

Select new position: Exit: MENU

Programme: 01 TVE 02 TVE2 03 TV3 04 C33 05 C27 06 C58 05 C27

the Programme Sorting menu appears automatically on the screen enabling you to change the order in which the channels appear on the screen.

a) If you do not wish to change the channel order, go to

step 6.

b) If you wish to change the channel order:

1 Press the or button to select the programme

to rearrange, then press the button.

channel (TV Broadcast), then press .

number with the channel (TV Broadcast) you wish

2 Press the or button to select the new

programme number position for your selected

3 Repeat steps b)1 and b)2 if you wish to change

the order of the other channels.

6 Press the MENU button to remove the menu from the

screen.

Your TV is now ready for use

First Time Operation

Page 10

Introducing and Using the Menu System

Your TV uses an on-screen menu system to guide you through the operations. Use the following buttons on the Remote Control to operate the menu system:

1 Press the MENU button to switch the first level menu on.

2 • To highlight the desired menu or option, press or .

• To enter to the selected menu or option, press .

• To return to the last menu or option, press .

• To alter settings of your selected option, press //or.

• To confirm and store your selection, press OK.

3 Press the MENU button to remove the menu from the screen.

Menu Guide

Level 1 Level 2 Level 3 / Function

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue

Reset

PICTURE ADJUSTMENT

The “Picture Adjustment” menu allows you to alter the picture adjustments.

To do that: after selecting the item you want to

alter press , then press repeatedly / /

or to adjust it and finally press OK to store the new adjustment. This menu also allows you to customise the picture mode based on the programme you are watching:

Personal (for individual settings). Live (for live broadcast programmes). Movie (for films).

• Brightness, Colour and Sharpness can only be alterated if “Personal” mode is selected.

• Hue is only available for NTSC colour signal (e.g: USA video tapes).

• Select Reset and press OK to reset the picture to the factory preset levels.

Menu System

continued...

Page 11

Level 1 Level 2 Level 3 / Function

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

SLEEP TIMER

The “Sleep Timer” option in the “Timer” menu allows you to select a time period for the TV to switch itself automatically into the standby mode.

Timer

Sleep Timer: Off

On Timer: Off

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Timer

Sleep Timer: Off

On Timer: Off

Timer

Sleep Timer: Off

On Timer: i Off

To do that: after selecting the option press , then press or to set the time period delay (max. of 4 hours) and finally press OK to store.

• While watching the TV, you can press the

button on the remote control to display the time remaining.

• One minute before the TV switches itself into standby mode, the time remaining is displayed on the TV screen automatically.

ON TIMER

The “On Timer” option in the “Timer” menu allows you to select a time period for the TV to switch itself automatically on from standby

mode.

To do that: after selecting the option press ,

then press or to set the time period delay

Timer

Sleep Timer: Off

On Timer: Off

(max. 12 hours) and press OK to store. Finally press the standby button control. After the selected length of time the TV

on the remote

switches on automatically.

• The standby indicator on the TV set flashes regularly to indicate that “On Timer” is active.

• Any loss of power will cause these settings to be cleared.

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

LANGUAGE

The “Language” option in the “Set Up” menu allows you to select the language that the menus are displayed in.

To do that: after selecting the option, press and then proceed in the same way as in the step 2 of the section “Switching On the TV and

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

Automatically Tuning”.

continued...

Menu System

Page 12

Level 1 Level 2 Level 3 / Function

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

AUTO TUNING

The “Auto Tuning” option in the “Set Up” menu allows you to automatically search for and store all available TV channels.

To do that: after selecting the option, press and then proceed in the same way as in steps 3 and 4 of the section “Switching On the TV and Automatically Tuning”.

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

PROGRAMME SORTING

The “Programme Sorting” option in the “Set Up” menu allows you to change the order in which the channels (TV Broadcast) appear on

the screen.

To do that: after selecting the option, press

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

and then proceed in the same way as in step 5 b) of the section “Switching On the TV and Automatically Tuning”.

MANUAL PROGRAMME PRESET

The “Manual Programme Preset” option in the “Set Up” menu allows you to:

a) Preset channels or a video input source one

by one to the programme order of your choice. To do that:

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

Manual Programme Preset

Programme: Channel: Label: AFT: Skip: Confirm

1 After selecting the ”Manual Programme

Preset” option, press then with Programme option highlighted press . Press or to select on which

programme number you want to preset the channel (for VCR, select programme number “0”). Then press .

01 C 21

--TVE On No

Menu System

continued...

Page 13

Level 1 Level 2 Level 3 / Function

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

Manual Programme Preset

Programme: Channel: Label: AFT: Skip: Confirm

2 After selecting the Channel option, press . Then press or to select the channel

tuning (“C” for terrestrial channels or “S” for cable channels). Next press . After that, press the number buttons to enter directly the channel number of the TV Broadcast or the channel of the VCR signal. If you do not know the channel number, press or to search for it. When you tune the desired channel, press OK twice to store.

Repeat all the above steps to tune and store more channels.

01 C 21

b)Normally the automatic fine tuning (AFT) is

--TVE On No

operating, however you can manually fine tune the TV to obtain a better picture

reception in the case that the picture is distorted.

To do that: while watching the channel (TV Broadcast) you wish to fine tune, select the AFT option and press . Next press or to adjust the fine tuning between -15 and +15. Finally press OK twice to store.

c) Skip any unwanted programme numbers

when they are selected with the PROGR +/buttons.

To do that: Highlighting the Programme

option, press the PROGR +/- button to select

the programme number you want to skip. When the programme you want to skip appears on the screen, select the Skip option and press . Next press or to select Yes. Finally press OK twice to confirm and store.

To cancel this function afterwards, select “No” instead of “Yes” in the step above.

d) Label a channel using up to five characters.

To do that: Highlighting the Programme option, press the PROGR +/- button to select the programme number with the channel you wish to name. When the programme you want to name appears on the screen, select the Label option and press . Next press o “-“ for a blank. Press to confirm this character. Select the other four characters in the same way. After selecting all the characters, press OK twice to store.

r to select a letter, number or

continued...

Menu System

Page 14

Level 1 Level 2 Level 3 / Function

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

Advanced Features

Parental Lock: Noise Reduction: Auto Volume Ctrl.: RGB Centring: Picture Rotation:

PARENTAL LOCK

The “Parental Lock” option in the “Advanced Features” menu allows you to lock the buttons of the TV set. In this way after this option is selected and the TV set is switched off, the buttons on the TV do not work and the TV only works by using the remote control buttons.

Off On On 0

To do that: after selecting the option, press .

Then press or to select On. Press OK to

confirm and store and finally press on the remote control.

To cancel this function afterwards, select “Off” instead of “On” in the step above.

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

NOISE REDUCTION

The “Noise Reduction” option in the “Advanced Features” menu allows you to reduce the picture noise in case of a weak

Advanced Features

Parental Lock: Noise Reduction: Auto Volume Ctrl.: RGB Centring: Picture Rotation:

broadcasting signal.

To do that: after selecting the option, press .

Off

Then press or to select On. Finally press

On On 0

OK to confirm and store.

To cancel this function afterwards, select “Off”

instead of “On” in the step above.

AUTO VOLUME CONTROL

The “Auto Volume Ctrl.” option in the “Advanced Features” menu allows you to keep the same volume level of the channels,

Advanced Features

Parental Lock: Noise Reduction: Auto Volume Ctrl.: RGB Centring: Picture Rotation:

independent of the broadcast signal (e.g. in case of advertisement).

Off

To do that: after selecting the option, press .

On On 0

Then press o

OK to confirm and store.

To cancel this function afterwards, select “Off”

r to select On. Finally press

instead of “On” in the step above.

Menu System

continued...

Page 15

Level 1 Level 2 Level 3 / Function

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

Advanced Features

Parental Lock: Noise Reduction: Auto Volume Ctrl.: RGB Centring: Picture Rotation:

RGB CENTRING

When connecting an RGB source, such as a “PlayStation”, you may need to readjust the geometry of the picture. In that case, you can readjust it through the “RGB Centring” option in the “Advanced Features”.

Off On

To do that: while watching an RGB source select

On 0

the “RGB Centring” option and press . Then

press or to adjust the centre of the

picture between –10 and +10. Finally press OK to confirm and store.

Picture Adjustment

Mode: Personal Contrast Brightness Colour Sharpness Hue Reset

Set Up

Language Auto Tuning Programme Sorting Manual Programme Preset Advanced Features

PICTURE ROTATION (only for KV-21LT1U)

Because of the earth’s magnetism, the picture might slant. In this case, you can correct the

Advanced Features

Parental Lock: Noise Reduction: Auto Volume Ctrl.: RGB Centring: Picture Rotation:

pictures slant by using the option “Picture Rotation” in the “Advanced Features” menu.

Off

To do that: after selecting the option, press .

On On 0

Then press or to correct any slant of the

picture between -5 and +5 and finally press OK

to store.

Menu System

Page 16

Teletext

Teletext is an information service transmitted by most TV stations. The index page of the teletext service (usually page 100) gives you information on how to use the service. To operate teletext, use the remote control buttons as indicated below.

Make sure to use a channel (TV Broadcast) with a strong signal, otherwise teletext errors may occur.

To Switch On Teletext :

After selecting the channel (TV Broadcast) which carries the teletext you wish to view, press .

To Select a Teletext page:

Input 3 digits for the page number, using the numbered buttons.

• If you have made a mistake, retype the correct page number.

• If the counter on the screen continues searching, it is because this page is not available. In that case,

input another page number

To access the next or preceding page:

Press PROGR + ( ) or PROGR - ().

To superimpose teletext on to the TV:

Whilst you are viewing teletext, press . Press it again to cancel teletext mode.

To freeze a teletext page:

Some teletext pages have sub-pages which follow on automatically. To stop them, press

/ . Press it again to cancel the freeze.

To reveal concealed information (e.g: answer to a quiz):

Press / . Press it again to conceal the information.

TELETEXT

Index

Programme

Programme News

News

News Sport

Sport

Sport Weather

Weather

153

153 101

101

To Switch Off Teletext:

Press .

Fastext

Fastext service lets you access pages with one button push.

While you are in Teletext mode and Fastext is broadcast, a colour coded menu appears at the bottom of the teletext page. Press the colour button (red, green, yellow or blue) to access the corresponding page.

Teletext

Page 17

Connecting Optional Equipment

Decoder

Using the following instructions, you can connect a wide range of optional equipment to your TV set. (Connecting cables are not supplied).

Connecting a VCR:

To connect a VCR, please refer to the section “Connecting the aerial and VCR” of this instruction manual. We recommend you connect your VCR using a scart lead. If you do not have a scart lead, tune in the VCR test signal to TV programme number “0”. by using “Manual Programme Preset” option. (for details how to manual programme, see page 12, step a). Also refer to your VCR instruction manual to find out how to find the output channel of your VCR.

* “PlayStation” is a product of Sony Computer Entertainment, Inc. * “PlayStation” is a trademark of Sony Computer Entertainment, Inc.

8mm/Hi8/DVC camcorder

“PlayStation”*

VCR

Using Optional Equipment

1 Connect your equipment to the designated TV socket, as indicated above.

2 To watch the picture of the connected equipment, press the button repeatedly until the

correct input symbol appears on the screen.

Symbol Input Signals

1 • Audio / video input signal through the Scart connector C

• RGB input signal through the Scart connector C. This symbol appears only

if a RGB source has been connected.

2 • Video input signal through the phono socket A and Audio input signal

through B.

3 Switch on the connected equipment.

4 Press button on the remote control to return to the normal TV picture.

Additional Information

Page 18

Specifications

TV system:

Colour system:

PAL, SECAM NTSC 3.58, 4.43 (only Video In)

Channel Coverage:

I: UHF B21-B69

Picture Tube:

Flat Display FD Trinitron

Rear Terminals

:1/ 21-pin scart connector

(CENELEC standard) including audio/video

Front Terminals

…2 video input – phono jack 2 audio input – phono jack

headphones jack

Sound Output:

• KV-21LT1U:

1 x 8 W (music power) 1 x 4 W (RMS Mono)

• KV-14LT1U:

1 x 6 W (music power) 1 x 3 W (RMS Mono)

input, RGB input, TV audio/ video output.

Power Consumption:

• KV-21LT1U: 76 W

• KV-14LT1U: 54 W

Standby Power Consumption:

≤ 0.55 W

Dimensions (w x h x d):

• KV-21LT1U: Approx. 514 x 478 x 487 mm.

• KV-14LT1U: Approx. 393 x 358 x 415 mm.

Weight:

• KV-21LT1U: Approx. 24 Kg.

• KV-14LT1U: Approx. 11.5 Kg.

Accessories supplied:

1 Remote Control (RM-887) 2 Batteries (IEC designated) 1 Loop aerial (only for KV-14LT1U)

Other features:

• Teletext, Fastext, TOPtext

• Sleep Timer

• Wake UP Timer

• Smartlink (direct link between your TV set and a compatible VCR. For more

information on Smartlink, please refer to

the Instruction Manual of your VCR).

Design and specifications are subject to change without notice.

Ecological Paper- Totally Chlorine Free

Additional Information

Page 19

Troubleshooting

Here are some simple solutions to the problems which may affect the picture and sound.

Problem

No picture (screen is dark) and no sound.

Poor or no picture (screen is dark), but good sound.

No picture or no menu information from the equipment connected to the Scart connector.

Good picture, no sound.

No colour on colour programmes.

Distorted picture when changing programmes or selecting teletext.

Picture slanted (only for KV-21LT1U)

Noisy picture when viewing a TV channel.

Remote control does not function.

The standby indicator on the TV flashes even though the “On Timer” function is not in use.

Solution

•Check the aerial connection.

• Plug the TV in and press the button on the front of TV.

•If the standby indicator is on, press button on the remote control.

•Using the menu system, select the “Picture Adjustment” menu and select “Reset” to return to the

factory settings.

•Check that the optional equipment is on and press the

button repeatedly on the remote control until the correct input symbol is displayed on the screen.

• Press the +/- button on the remote control.

• Using the menu system, select the “Picture Adjustment” menu and select “Reset” to return to factory settings.

• Turn off any equipment connected to the Scart

connector on the rear of the TV.

• Using the menu system, select the “Picture Rotation”

option in the “Advanced Features” menu to correct the picture slant.

• Using the menu system, select the “Manual Programme Preset” menu and adjust Fine Tuning

(AFT) to obtain better picture reception.

• Using the menu system, select the “Noise Reduction”

option in the “Advanced Features” menu and select “On” to reduce the noise in the picture.

• Replace the batteries.

• Contact to your nearest Sony service centre.

In case of problems, have your TV serviced by qualified personnel. Never open the casing yourself.

Additional Information

Page 20

Television Channel Number Guide for United Kingdom

Only the main transmitters are listed. Information regarding the regional sub-relay channel numbers can be obtained by contacting The BBC Engineering Information Dept., Telephone Number 020 7852 5040.

Additional Information

Page 21

Printed in UK

Page 22

Page 23

Page 24

Printed in UK

Sony KV-21LT1U, KV-14LT1U User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual