Sony KDL-46HX850 Schematic
SERVICE MANUAL
Version Date Subject
1.0 4/2012 Original manual issue.
2.0 4/2012 Corrected P/N.(P.145)
3.0 4/2012 Corrected text.(P.7~13)
LCD Digital Color TV
9-888-487-03
HISTORY INFORMATION FOR THE FOLLOWING MANUAL:
ORIGINAL MANUAL ISSUE DATE: 4/2012
AZ3F CHASSIS
Segment: 3a-G
SERVICE MANUAL
LCD Digital Color TV
AZ3F CHASSIS
Segment: 3a-G
9-888-487-03
KDL-40/46/55HX850,853,855(AEP/UK/IT)
3
MODEL LIST
MODEL COLOR COMMANDER DEST.MODEL COLOR COMMANDER DEST.
KDL-40HX850 Black RM-ED047 AEP
KDL-40HX853 Black RM-ED047 AEP/UK
KDL-40HX855 Black RM-ED047 AEP/IT
KDL-46HX850 Black RM-ED047 AEP
KDL-46HX853 Black RM-ED047 AEP/UK
KDL-46HX855 Black RM-ED047 AEP/IT
KDL-55HX850 Black RM-ED047 AEP
KDL-55HX853 Black RM-ED047 AEP/UK
KDL-55HX855 Black RM-ED047 AEP/IT
KDL-40/46/55HX850,853,855(AEP/UK/IT)
4
WARNINGS AND CAUTIONS - ENGLISH
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
WARNING!!
An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis.
The chassis of this receiver is directly connected to the ac power line.
CARRYING THE TV
Be sure to follow these guidelines to protect your property and avoid causing serious injury.
• Carry the TV with an adequate number of people; larger size TVs require two or more people.
• Correct hand placement while carrying the TV is very important for safety and to avoid damages.
SAFETY-RELATED COMPONENT WARNING!!
Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony
parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identified in this manual.
Follow these procedures whenever critical components are replaced or improper operation is suspected.
KDL-40/46/55HX850,853,855(AEP/UK/IT)
5
WARNINGS AND CAUTIONS - FRENCH
ATTENTION!!
Ces instructions de service sont à l’usage du personnel de service qualifi é seulement.
Pour prévenir le risque de choc électrique, ne pas faire l’entretien autre que celui contenu dans le Mode d’emploi à moins que vous soyez qualifi é faire ainsi.
WARNING!!
Afi n d’eviter tout risque d’electrocution provenant d’un chássis sous tension, un transformateur d’isolement doit etre utilisé lors de tout dépannage. Le chássis de ce récepteur est
directement raccordé à l’alimentation du secteur.
POUR TRANSPORTER LE TÉLÉVISEUR
Tenez compte de ce qui suit pendant l’installation du téléviseur :
• Débranchez tous les câbles avant de transporter le téléviseur.
• Transportez le téléviseur avec le nombre de personnes approprié ; un téléviseur de grande taille doit être transporté par au moins deux personnes.
• Lors du transport du téléviseur, l’emplacement des mains est très important pour votre sécurité, ainsi que pour éviter de causer des dommages.
ALERTE!!
Afi n d’eviter tout risque d’electrocution provenant d’un chassis sous tension, un transformateur d’isolement doit etre utilise lors de tout depannage. Le chassis de ce recepteur est
directement raccorde a l’alimentation du secteur.
ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!
Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont d’une importance critique pour la securite du
fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages
de circuit dont l’importance est critique pour la securite du fonctionnement sont identifi es dans le present manuel. Suivre ces procedures lors de chaque remplacement de
composants critiques, ou lorsqu’un mauvais fonctionnement suspecte.
KDL-40/46/55HX850,853,855(AEP/UK/IT)
6
WARNINGS AND CAUTIONS
USE CAUTION WHEN HANDLING THE LCD PANEL
When repairing the LCD panel, be sure you are grounded by using a wrist band.
When repairing the LCD panel on the wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.
1) Do not press on the panel or frame edge to avoid the risk of electric shock.
2) Do not scratch or press on the panel with any sharp objects.
3) Do not leave the module in high temperatures or in areas of high humidity for an extended period of time.
4) Do not expose the LCD panel to direct sunlight.
5) Avoid contact with water. It may cause a short circuit within the module.
6) Disconnect the AC power when replacing the backlight (CCFL) or inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms.)
7) Always clean the LCD panel with a soft cloth material.
8) Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short.
9) Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).
10) It is recommended not to exceed 1 hour of Power-On nor Burn-in period with LCD panel face down condition, in repair activity.
KDL-40/46/55HX850,853,855(AEP/UK/IT)
7
1. HANDLING THE TENGO PANEL
When handling the TENGO panel, please follow the instructions below.
Hold more than 200mm from the short side
WARNINGS AND CAUTIONS
Fig.1
Fig.2
- Do not hold the panel at the end of the long side. Leave at least 200 mm with the short side. (Fig. 1)
- Always put down the panel with great caution. (Fig. 2)
KDL-40/46/55HX850,853,855(AEP/UK/IT)
8
Will bent easily
WARNINGS AND CAUTIONS
Fig.1 Fig.2 Fig.3
Fig.5
Fig.4
WARNING: Handling the panel as depicted below is strictly forbidden, otherwise resin separation / cracking of glass may occur.
1. DO NOT put the panel on a cushion which is not supporting the panel along its total length. (Fig.1)
2. DO NOT put the bottom of glass directly on the repair surface. (Fig.2)
3. DO NOT hold (and press) the glass side with the palm of your hand. (Fig.3)
4. DO NOT hold the short side of the panel. (Fig.4)
5. DO NOT hold only the glass plate when the glass side is up. (Fig.5)
KDL-40/46/55HX850,853,855(AEP/UK/IT)
9
WARNINGS AND CAUTIONS
Fig.3
Fig.4
When replacing the TENGO panel at service, please keep in mind the 10 guidelines on the following pages.
1. Unpack the cardboard box and pull out the panel with reinforcing plates. (Fig.3)
2. Together with the reinforcing plates, put down the panel horizontally with the face down. (Fig.4)
Note: Please use the reinforcing plates as operating table.
2. NOTES ON REPLACING THE TENGO PANEL
KDL-40/46/55HX850,853,855(AEP/UK/IT)
10
WARNINGS AND CAUTIONS
Fig.6Fig.5
3. Unpack the TENGO panel. (Fig.5)
4. Cut the protection bag at the centre of the back of panel. (Fig.6)
Note: As the bag will be used for repacking, please cut the protection bag carefully.
KDL-40/46/55HX850,853,855(AEP/UK/IT)
11
WARNINGS AND CAUTIONS
Fig.7 Fig.8
5. Assemble the TV set with the new panel. (Fig.7)
6. After assembling, attach the Stand Unit and position the TV upright. (Fig.8)
KDL-40/46/55HX850,853,855(AEP/UK/IT)
12
Hold more than 200mm from short side
WARNINGS AND CAUTIONS
Fig.10Fig.9
7. Position the plastic bag correctly on the package and place the replaced panel on it. (Fig.9)
Note: Do not hold the panel at the end of the long side. Leave at least 200 mm with the short side.
8. Align the bottom side of panel with the cushions on the package. (Fig.10)
Note: The glass surface may get damaged if you pack the panel in the wrong direction. Prevent hitting the glass of the panel to any package material.
KDL-40/46/55HX850,853,855(AEP/UK/IT)
13
Fig.11
Fig.12
WARNINGS AND CAUTIONS
9. Tape the plastic bag on the back of panel to protect the panel surface. (Fig.11)
10. Confirm the orientation of the panel again. The T-CON board side must be at the lower end.
11. Repack the panel in the original cardboard box. (Fig.12)
KDL-40/46/55HX850,853,855(AEP/UK/IT)
14
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
8. For safety reasons, repairing the Power board and/or Inverter board is prohibited.
KDL-40/46/55HX850,853,855(AEP/UK/IT)
15
SAFETY CHECK-OUT
Leakage Test
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed
metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’
instructions to use these instructions.
2. A battery-operated AC milliampmeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The
“limit” indication is 0.75 V, so analog meters must have an accurate low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of passive VOMs that are suitable. Nearly all
battery-operated digital multimeters that have a 2 VAC range are suitable (see Figure A).
How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground; the cover-plate retaining screw on most AC outlet boxes is also
at earth ground.
If the retaining screw is to be used as your earth ground, verify that it is at ground by measuring the resistance
between it and a cold-water pipe with an ohmmeter. The reading should be zero ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble- light (not a neon lamp) between the hot
side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side on the line; the
lamp should light at normal brilliance if the screw is at ground potential (see Figure B).
KDL-40/46/55HX850,853,855(AEP/UK/IT)
16
SELF DIAGNOSIS FUNCTION
DIAGNOSTIC TEST INDICATORS
When an error occurs, the STANDBY LED will flash a set number of times to
indicate the possible cause of the problem.
If there is more than one error, the LED will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen.
If the screen displays a “0”, no error has occurred .
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the STANDBY LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these
problems occur.
0.5
0.5
3
DISPLAY OF STANDBY LED FLASH COUNT
SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurrences of failure for
confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
5
*
: Note that this differs from entering the service mode (volume +)
*
DISPLAY TV POWERChannel Volume
STBY LED
Flash time
Service menu Item
name
(Screeen Display)
Diagnostic Item Description
2 MAIN_POWE Main 12 V failure
DC_ALERT Main 5.0/3.3/1.2 V failur
AUD_PROT Audio amp. Protection
HDMI_EQ HDMI equalizer/switch I2C NACK
TU_DEMOD Tuner or demodulator I2C NACK
4 LD_ERR LED driver failure/LED voltage protection
P_ID_ERR Panel ID EEPROM I2C NACK
HFR_ERR FRC device I2C NACK
TCON_ERR FRC device Initialization failure
TCON_ERR E Micro (PEM) not started
6 BACKLITE Backlight converter OVP
TEMP_ERR Over temperature protection
TEMP_ERR Temp. sens or I2C NACK
8 -
Software Error (Also the main board’s m em ory or Wi-
Fi module is a suspect)
9 - Not used
10 EMIT_ERR
Transmitter board not connected, protection
(3D models only)
11 - Not used
12 - Not used
3
5
7
KDL-40/46/55HX850,853,855(AEP/UK/IT)
17
SELFCHECK
000RESERVEDŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
000RESERVEDŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
002MAIN_POWEŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
003DC_ALERTŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
003AUD_PROTŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
003HDMI_EQŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
003TU_DEMODŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
004VLEDŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
004LD_ERRŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
005HFR_ERRŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
005TCON_ERR1108231325 ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ01
005P_ID_ERRŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
006BACKLITEŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
007TEMP_ERRŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
007FAN_ERRŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
010EMITTERŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
101VPC_WDTŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
102MEPS_WDTŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
103HOST_WDTŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ00
104STB
Y_WDTŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ ŞŞŞŞŞŞŞŞŞŞ 00
0081Ş00671Ş00088
SELF DIAGNOSIS FUNCTION
[SELF DIAGNOSTIC SAMPLE SCREEN DISPLAY]
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen.
After you have completed the repairs, clear the result display to “0”.
Clearing the Self Check Diagnostic List
1. Error history and Error count : Press the Channel 8 => Channel 0 .
2. Panel operation time : Press the Channel 7 => Channel 0 .
Exiting the Self-diagnostic screen
To exit the Self Diagnostic screen, turn off the power to the TV by pressing the POWER button on the remote or the POWER button on the TV.
Error count (00-99)
Error history (Last failure time beforehand) *1
Error history (Failure time before last) *1
Error history (The last failure time) *1
Item name
STBY LED flash time
Total operation time by hour (MAX:65535)
Boot count (MAX:65535)
Panel operation time by hour (MAX:65535)
CPU Watch-dog timer
*1 : Format of error history
YYMMDDhhmm (in UTC)
Example:1108231325 -> Aug 23 13:25 2011 UTC
KDL-40/46/55HX850,853,855(AEP/UK/IT)
18
SEC 1. DISASSEMBLY
• There are clutch in the yellow frame[ ]. Therefore please be careful in the case of the disassembly or assembly of parts.
Note: When removing the rear cover, to prevent damaging the rear cover, please refer to “
APPENDIX-1
”..
Note: Metal type Rear Cover is used in these models.
When handle the Rear Cover, please pay special attention to the sharp edges due to no curing finish.
When working, wearing gloves is recommended.
Location of the sharp edges, please refer to “
APPENDIX-2
”.
KDL-40/46/55HX850,853,855(AEP/UK/IT)
19
1-1. KDL-40HX850/853/855
1-1-1. BUNCHIN ASSY, HEAD COVER AND NECK
DISASSEMBLY
3 Screws (SCREW,+PSW M5X 16) P/N: FX0029601
1 2
3 Screws (SCREW,+PSW M5X 16) P/N: FX0029601
3 Screws (SCREW,+PSW M5X 16) P/N: FX0029601
3
NECK
HEAD COVER
BUNCHIN ASSY
KDL-40/46/55HX850,853,855(AEP/UK/IT)
20
16 Screws (SCREW,+PSW M3X 8) P/N: 2-580-593-01
7 Screws (SCREW +BVTP 4X12 TYPE2 IT-3) P/N:FX0005801
1-1. KDL-40HX850/853/855
DISASSEMBLY
6 Screws (SCREW,+PSW M3X 8) P/N: 2-580-593-01
1 2
3
1-1-2. BASE PLATE, BASE COVER, TOP PLATE, SPEAKER AND SOUND BAR STAND CABLE
SOUND BAR STAND CABLE
SPEAKER
BASE PLATE
TOP PLATE
BASE COVER
KDL-40/46/55HX850,853,855(AEP/UK/IT)
21
DISASSEMBLY
1-1-3. AC COVER AND POWER SUPPLY CORD
1 Screw (SCREW, +PSW M3X6 W12) P/N: FX0001901
1-1. KDL-40HX850/853/855
REAR COVERAC COVER
Note: When assemble the AC COVER, hold the AC COVER and tighten a screw.
POWER SUPPLY CORD
Note: Confirm Insulation sheet is seen.
CABLE CLAMPER
KDL-40/46/55HX850,853,855(AEP/UK/IT)
22
DISASSEMBLY
1-1-4. REAR COVER (1/2)
2 Screws (JOINT, SCREW) P/N: FX0050801
4 Screws (SCREW +BVTP 3X10 TYPE2 IT-3) P/N:FX0012779
14 Screws (SCREW, +PSW M3X6 W12) P/N: FX0001901
2 Screws (SCREW, ORNAMENTAL M6X12) P/N: FX0006302
1-1. KDL-40HX850/853/855
REAR COVER
Note: When screw top side 2 corner, please hold Rear Cover as below picture.
KDL-40/46/55HX850,853,855(AEP/UK/IT)
23
DISASSEMBLY
1-1-4. REAR COVER (2/2)
1-1. KDL-40HX850/853/855
1
2
KDL-40/46/55HX850,853,855(AEP/UK/IT)
24
DISASSEMBLY
1-1-5. SHEET, ANT(G)
1-1. KDL-40HX850/853/855
SHEET, ANT(G)
SHEET, ANT(G)
SHEET, ANT(G)
KDL-40/46/55HX850,853,855(AEP/UK/IT)
25
DISASSEMBLY
1-1-6. SWITCH UNIT
SWITCH UNIT
1-1. KDL-40HX850/853/855
SWITCH UNITSWITCH UNIT
1
32
KDL-40/46/55HX850,853,855(AEP/UK/IT)
26
1-1-7. ANTENNA
DISASSEMBLY
1-1. KDL-40HX850/853/855
1 2
1 2
<A>
<B>
<B><A>
1 Screw (SCREW (+PSW) (M3X6)) P/N: FX0001341
1 Screw (SCREW (+PSW) (M3X6)) P/N: FX0001341
ANTENNA
ANTENNA
ANTENNA
ANTENNA
KDL-40/46/55HX850,853,855(AEP/UK/IT)
27
1-1-8. WIRELESS LAN CARD
DISASSEMBLY
2
WIRELESS LAN CARD WIRELESS LAN CARD
1-1. KDL-40HX850/853/855
3
1
2 Screws (SCREW (+PSW) (M3X6)) P/N: FX0001341
WIRELESS LAN CARD
Note: Refer to the connection from the antenna when
installing a wireless module.
KDL-40/46/55HX850,853,855(AEP/UK/IT)
28
DISASSEMBLY
1-1-9. CONNECTOR, HARNESS AND FFC
FLEXIBLE FLAT CABLE
CONNECTOR ASSY 28P
1-1. KDL-40HX850/853/855
CONNECTOR ASSY 14P
HARNESS ASSY
KDL-40/46/55HX850,853,855(AEP/UK/IT)
29
1-1-10. UNDER BRACKET
DISASSEMBLY
1
BAP BOARD
UNDER BRACKET
1-1. KDL-40HX850/853/855
2
BAP BOARD
UNDER BRACKET
KDL-40/46/55HX850,853,855(AEP/UK/IT)
30
1-1-11. SIDE BRACKET
DISASSEMBLY
1-1. KDL-40HX850/853/855
1
2
SIDE BRACKET
SIDE BRACKET
BAP BOARD
BAP BOARD
Loading...