Sony KDL-40S4100, KDL-46S4100 Service Manual
HISTORY INFORMATION FOR THE FOLLOWING MANUAL:
SERVICE MANUAL
MODEL NAME REMOTE COMMANDER DESTINATION
KDL-40S4100
KDL-40S4100
KDL-40S4100
KDL-46S4100
KDL-46S4100
KDL-46S4100
RM-YD025 CANADA
RM-YD025 MEXICO
RM-YD025 US
RM-YD025 CANADA
RM-YD025 MEXICO
RM-YD025 US
FX
CHASSIS
ORIGINAL MANUAL ISSUE DATE: 4/2008
:UPDATED ITEM
☛
REVISION DATE SUBJECT
4/2008 No revisions or updates are applicable at this time.
5/2008 Reissue entire service manual to include PWBs.
8/2008 Reissue entire manual due to multiple updates.
10/2008 Removed Self Diagnosis logo from Front Cover and Self Diagnostic Function page.
Replaced pages 2 and 11.
Updated Table of Contents. Replaced page 3.
Added Inverter Connector Assembly to Disassembly Section. Replaced pages 12-20.
10/2008 Removed part number information for AC Inlet. Replaced page 55.
LCD DIGITAL COLOR TELEVISION
9-883-778-05
SERVICE MANUAL
MODEL NAME REMOTE COMMANDER DESTINATION
FX
CHASSIS
KDL-40S4100
KDL-40S4100
KDL-40S4100
KDL-46S4100
KDL-46S4100
KDL-46S4100
RM-YD025 CANADA
RM-YD025 MEXICO
RM-YD025 US
RM-YD025 CANADA
RM-YD025 MEXICO
RM-YD025 US
9-883-778-05
KDL-40S4100 RM-YD025
LCD DIGITAL COLOR TELEVISION
KDL-40S4100/46S4100
TABLE OF CONTENTS
SECTION TITLE PAGE SECTION TITLE PAGE
Specifi cations ................................................................................. 4
Warnings and Cautions - ENGLISH ............................................... 6
Warnings and Cautions - FRENCH ................................................ 7
Safety-Related Component Warning .............................................. 8
Safety Check-Out ......................................................................... 10
Self-Diagnostic Function ................................................................11
SECTION 1: DISASSEMBLY ............................................................... 12
1-1. Rear Cover Removal ............................................................ 12
1-2. Function Key Removal and H1 Board Removal ................... 12
1-3. A Board and G Board Removal ............................................ 13
1-4. Table-Top Stand Assembly and Under Cover Removal ....... 13
1-5. AC Inlet and Bracket Removal ............................................. 14
1-6. Structural Frames and Brackets Removal
(KDL-40S4100 Only) ............................................................ 14
1-7. Structural Frames and Brackets Removal
(KDL-46S4100 Only) ............................................................ 15
1-8. Loudspeaker Removal ......................................................... 16
1-9. Bottom Cover, H2 Board, H3 Board and
LED Lens Removal .............................................................. 16
1-10. LCD Panel Removal ............................................................. 17
1-10-1. Detaching the Inverter Connector Assembly ........... 17
1-10-2. Attaching the Inverter Connector Assembly ............. 18
1-10-3. Cleaning the LCD Panel .......................................... 18
1-11. Balancer (ETC-Inverter MT) Board Removal ....................... 19
Wire Dressing ............................................................................... 20
Overall View ......................................................................... 20
SECTION 2: SERVICE ADJUSTMENTS ............................................. 21
2-1. Resetting to Factory Defaults after Board Replacement ...... 21
SECTION 3: DIAGRAMS ..................................................................... 22
3-1. Circuit Boards Location ........................................................ 22
3-2. Printed Wiring Boards and
Schematic Diagrams Information ......................................... 22
3-3. Block Diagram ...................................................................... 24
3-4. Schematics and Supporting Information .............................. 25
A Board Schematic Diagram (1 of 19) .................................. 25
A Board Schematic Diagram (2 of 19) .................................. 26
A Board Schematic Diagram (3 of 19) .................................. 27
A Board Schematic Diagram (4 of 19) .................................. 28
A Board Schematic Diagram (5 of 19) .................................. 29
A Board Schematic Diagram (6 of 19) .................................. 30
A Board Schematic Diagram (7 of 19) .................................. 31
A Board Schematic Diagram (8 of 19) .................................. 32
A Board Schematic Diagram (9 of 19) .................................. 33
A Board Schematic Diagram (10 of 19) ................................ 34
A Board Schematic Diagram (11 of 19) ................................ 35
A Board Schematic Diagram (12 of 19) ................................ 36
A Board Schematic Diagram (13 of 19) ................................ 37
A Board Schematic Diagram (14 of 19) ................................ 38
A Board Schematic Diagram (15 of 19) ................................ 39
A Board Schematic Diagram (16 of 19) ................................ 40
A Board Schematic Diagram (17 of 19) ................................ 41
A Board Schematic Diagram (18 of 19) ................................ 42
A Board Schematic Diagram (19 of 19) ................................ 43
G Board Schematic Diagram (1 of 3) ................................... 46
G Board Schematic Diagram (2 of 3) ................................... 47
G Board Schematic Diagram (3 of 3) ................................... 48
H1 Board Schematic Diagram .............................................. 51
H2 Board Schematic Diagram .............................................. 52
H3 Board Schematic Diagram .............................................. 53
KDL-40S4100/46S4100
SECTION 4: EXPLODED VIEWS ........................................................ 54
4-1. Rear Cover Assembly and Table-Top Stand Assembly ....... 54
4-2. Chassis ................................................................................ 55
4-3. Bezel Assembly and LCD Panel (KDL-40S4100 Only) ........ 56
4-4. Bezel Assembly and LCD Panel (KDL-46S4100 Only) ........ 57
4-5. Screw Legend ...................................................................... 58
APPENDIX A: ENCRYPTION KEY COMPONENTS ..........................A-1
3
SPECIFICATIONS
KDL-40S4100/46S4100
Power Requirements
120V - 240V AC, 50/60Hz
VIDEO (IN) 1/2:
S Video (4-Pin Mini DIN) (Video 1 only)
Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative
C: 0.286 Vp-p (Burst signal), 75 ohms
Video
1 Vp-p, 75 ohms unbalanced, sync negative
Audio
500 mVrms (100% modulation)
Impedance:47 kilohms
COMPONENT IN 1/2:
YP
(Component Video)
BPR
Y:1.0 Vp-p, 75 ohms unbalanced, sync negative
PB:0.7 Vp-p, 75 ohms
PR:0.7 Vp-p, 75 ohms
Signal format: 480i, 480p, 720p, 1080i, 1080p
Audio
500 mVrms (100% modulation)
Impedance: 47 kilohms
HDMI IN 1/2/3:
HDMI
Video: 480i, 480p, 720p, 1080i, 1080p, 1080/24p
Audio: Two channel linear PCM 32, 44.1, and 48 kz,
16, 20 and 24 bits
Audio (HDMI IN 1 only):
500 mVrms (100% modulation)
Impedance: 47 kilohms
AUDIO OUT:
500 mVrms (100% modulation)
More than 500 mVrms (Fixed)
DIGITAL AUDIO OUT (OPTICAL):
Optical Digital Audio Output (PCM/Dolby Digital)
PC IN:
Analog RGB (D-sub 15-pin):
0.7 Vp-p, 75 ohms, positive
Audio (Stereo mini jack):
500 mVrms
Impedance: 47 kilohms
KDL-40S4100/46S4100
4RADEMARK)NFORMATION
-ACINTOSHISATRADEMARKOF!PPLE)NCREGISTEREDINTHE53ANDOTHER
COUNTRIES
($-)THE($-)LOGOAND(IGH$EFINITION-ULTIMEDIA)NTERFACEARE
TRADEMARKSORREGISTEREDTRADEMARKSOF($-),ICENSING,,#
-ANUFACTUREDUNDERLICENSEFROM$OLBY,ABORATORIESh$OLBYvANDTHE
DOUBLE$SYMBOLARETRADEMARKSOF$OLBY,ABORATORIES
"LURAY$ISCISATRADEMARK
h"2!6)!v AND ARETRADEMARKSOF3ONY#ORPORATION
Design and specifi cations are subject to change without notice.
4
Power Consumption
in use
in standby Less than 1.0 W Less than 1.0 W
Speaker Output (W)
mm 57.5 x 126 65 x 147
Dimensions (W x H x D)
with stand
mm
Dimensions (W x H x D)
without stand
mm
Mass
with stand
without stand
KDL-40S4100 KDL-46S4100
210W 260W
10W + 10W 10W + 10W
in
3/8
2
x 5 2
5/8
x 5
7/8
997 x 689 x 276 1130 x 784 x 308 mm
in
39
3/8
x 27
1/4
x 10
7/8
44
1/2
x 30
7/8
x 12
997 x 652 x 111 1130 x 746 x 115
3/8
3/4
in
kg
39
x 25
x 4
3/8
22.7kg 30kg
44
1/2
x 29
3/8
x 4
lbs 50 lbs 1 oz 66 lbs 3 oz
kg
19.9kg 26.5 kg
lbs 43 lbs 14 oz 58 lbs 7 oz
All measurements are approximations.
KDL-40S4100/46S4100
1/4
5/8
Television system
NTSC American TV Standard
ATSC (8VSB terrestrial) ATSC compliant 8VSB
QAM on cable ANSI/SCTE 07 2000
Channel coverage
Analog Digital
Terrestrial 2-69 2-69
Cable 1-135 1-135
Antenna
75-ohm external terminal for VHF/UHF
Panel System
LCD (Liquid Crystal Display) Panel
Display Resolution (horizontal x vertical):
1,920 dots x 1,080 lines
Screen Size (measured diagonally)
approx. 40 inches (KDL-40S4100 only)
approx. 46 inches (KDL-46S4100 only)
Supplied Accessories
Remote Commander RM-YD025
Two Size AA (R6) Batteries
AC Power Cord
Table-Top Stand
Screws (4)
Cable Band
Operating Instructions
Quick Setup Guide
Warranty Card
Online Registration Card (US only)
Optional Accessories
Connecting Cables
Support Belt Kit
Wall-Mount Bracket
SU-WL500
TV Stand
WS-S10LS/SU-FL300M (KDL-40S4100 only)
WS-S10LS/SU-FL300M/SU-FL300L (KDL-46S4100 only)
KDL-40S4100/46S4100
5
KDL-40S4100/46S4100
WARNINGS AND CAUTIONS - ENGLISH
CAUTION
These servicing instructions are for use by qualifi ed service personnel only. To reduce the risk of electric shock, do not perform any servicing other
than that contained in the operating instructions unless you are qualifi ed to do so.
CARRYING THE TV
To avoid dropping the TV and causing serious injury, be sure to follow
these guidelines:
Before carrying the TV, disconnect all cables.
Carrying the large size TV requires two or more people.
When you carry the TV, place your hand as illustrated and hold it
securely. Do not put stress on the LCD panel.
When carrying, do not subject the TV to shocks or vibration, or
excessive force.
When lifting or moving the TV, hold it firmly from the bottom. Place
your palm directly underneath but do not squeeze the panel’s speaker
grille area.
When carrying the TV, to avoid pinching your hands or fingers do not
put your hands between the TV and stand, or hold the bottom corner
of the TV.
WARNING!!
An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis. The chassis of this receiver is
directly connected to the ac power line.
! SAFETY-RELATED COMPONENT WARNING!!
Components identifi ed by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace
these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that
are critical for safe operation are identifi ed in this manual. Follow these procedures whenever critical components are replaced or improper operation is
suspected.
KDL-40S4100/46S4100
6
KDL-40S4100/46S4100
WARNINGS AND CAUTIONS - FRENCH
ATTENTION!!
Ces instructions de service sont à l’usage du personnel de service qualifi é seulement. Pour prévenir le risque de choc électrique, ne pas faire
l’entretien autre que celui contenu dans le Mode d’emploi à moins que vous soyez qualifi é faire ainsi.
TRANSPORTER LE TÉLÉVISEUR
Pour éviter d’échapper le téléviseur et de causer des blessures graves,
assurez-vous de suivre ces directives :
Avant de transporter le téléviseur, débranchez tous les câbles.
Il faut deux personnes ou plus pour transporter le téléviseur de grande
dimension.
Lorsque vous transportez le téléviseur, placez votre main tel qu’illustré
et tenez-le fermement. N’imposez pas de charge sur le panneau ACL.
Lorsque vous transportez le téléviseur, ne le soumettez pas à des chocs,
à des vibrations ou à une force excessive.
Lorsque vous soulevez ou déplacez le téléviseur, tenez-le fermement à
partir du bas. Placez votre paume directement en dessous, mais
n’appuyez pas sur le panneau avant ou la région encastrée.
Lorsque vous transportez le téléviseur, pour éviter de pincer vos mains
ou vos doigts, ne placez pas vos mains entre le téléviseur et le suppor
ou ne tenez pas le coin inférieur du téléviseur.
Afi n d’eviter tout risque d’electrocution provenant d’un chássis sous tension, un transformateur d’isolement doit etre utilisé lors de tout dépannage. Le
chássis de ce récepteur est directement raccordé à l’alimentation du secteur.
! ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!
Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont d’une
importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le
present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance est critique pour la securite du fonctionnement
sont identifi es dans le present manuel. Suivre ces procedures lors de chaque remplacement de composants critiques, ou lorsqu’un mauvais
fonctionnement suspecte.
KDL-40S4100/46S4100
7
SAFETY-RELATED COMPONENT WARNING
KDL-40S4100/46S4100
There are critical components used in LCD color TVs that are important for safety. These components are identifi ed with shading and
mark on the schematic diagrams and the electrical parts list. It is essential that these critical parts be replaced only with the part number
specifi ed in the electrical parts list to prevent electric shock, fi re, or other hazard.
NOTE: Do not modify the original design without obtaining written permission from the manufacturer or you will void the original parts and
labor guarantee.
!
USE CAUTION WHEN HANDLING THE LCD PANEL
When repairing the LCD panel, be sure you are grounded by using a wrist band.
When installing the LCD panel on a wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.
To avoid damaging the LCD panel:
do not press on the panel or frame edge to avoid the risk of electric shock.
do not scratch or press on the panel with any sharp objects.
do not leave the module in high temperatures or in areas of high humidity for an extended period of time.
do not expose the LCD panel to direct sunlight.
avoid contact with water. It may cause a short circuit within the module.
disconnect the AC adapter when replacing the backlight (CCFL) or inverter circuit.
(High voltage occurs at the inverter circuit at 650Vrms.)
always clean the LCD panel with a soft cloth material.
use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short.
protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).
LEAKAGE CURRENT HOT CHECK CIRCUIT
KDL-40S4100/46S4100
8
The circuit boards used in these models have been processed using
Lead Free Solder. The boards are identified by the LF logo located
close to the board designation e.g. H1 etc [ see example ]. The
servicing of these boards requires special precautions to be taken as
outlined below.
KDL-40S4100/46S4100
example 1
It is strongly recommended to use Lead Free Solder material in order to guarantee optimal quality of new solder joints.
Lead Free Solder is available under the following part numbers :
rebmuntraP retemaiD skrameR
91-500-046-7mm3.0gK52.0
02-500-046-7mm4.0gK05.0
12-500-046-7mm5.0gK05.0
22-500-046-7mm6.0gK52.0
32-500-046-7mm8.0gK00.1
42-500-046-7mm0.1gK00.1
52-500-046-7mm2.1gK00.1
62-500-046-7mm6.1gK00.1
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade.
This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics.
For more information on the use of Lead Free Solder, please refer to
http://www.sony-training.com
KDL-40S4100/46S4100
9
SAFETY CHECK-OUT
KDL-40S4100/46S4100
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or
touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and
mounting hardware have been replaced. Be absolutely certain that
you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
6. Check the line cords for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instructions.
2. A battery-operated AC milliampmeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of
passive VOMs that are suitable. Nearly all battery-operated digital
multimeters that have a 2 VAC range are suitable (see Figure A).
How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground; the cover-plate
retaining screw on most AC outlet boxes is also at earth ground. If the
retaining screw is to be used as your earth ground, verify that it is at
ground by measuring the resistance between it and a cold-water pipe
with an ohmmeter. The reading should be zero ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt
trouble- light (not a neon lamp) between the hot side of the receptacle
and the retaining screw. Try both slots, if necessary, to locate the hot
side on the line; the lamp should light at normal brilliance if the screw
is at ground potential (see Figure B).
Leakage Test
0.15 μF
Figure A. Using an AC voltmeter to check AC leakage. Figure B. Checking for earth ground.
To Exposed Metal
Parts on Set
Earth Ground
AC
Voltmeter
(0.75V)
Trouble Light
AC Outlet Box
Ohmmeter
Cold-water Pipe
KDL-40S4100/46S4100
10
KDL-40S4100/46S4100
SELF-DIAGNOSTIC FUNCTION
IMPORTANT:
The units in this manual DO NOT contain a self-diagnostic function. If an error occurs, the TV will not stay on. It is our recommendation that if a repair
is required for this set, the technician should bring both the A Board and the G Board to the customer location.
Control Buttons
TIMER STANDBY
Description of LED Indictors
The units in this manual DOES NOT contain a self-diagnostic function.
POWER
KDL-40S4100/46S4100
11
1-1. REAR COVER REMOVAL
1
Remove 2 screws from HDMI connectors
2
Remove 2 screws from terminal positions
3
Remove 6 screws
4
Remove 19 screws
KDL-40S4100/46S4100
SECTION 1: DISASSEMBLY
Rear Cover
1
2
4
1-2. FUNCTION KEY REMOVAL AND H1 BOARD REMOVAL
1
Remove 2 screws
2
Release hooks and remove Function Key and H1 Board
3
Disconnect 1 connector
4
Remove 1 screw and release Ground Wire
Key Cover
2
Function Key
3
H1 Board
3
1
4
KDL-40S4100/46S4100
Bezel
12
1-3. A BOARD AND G BOARD REMOVAL
1
Disconnect 4 connectors
2
Remove 1 screw from Side Bracket
3
Remove 1 screw from HDMI position
4
Remove 2 screws
5
Remove 8 screws
6
Remove Hexagon Nut from tuner
7
Remove 1 screw
8
Remove 9 screws
(KDL-40S4100 ONLY)
Remove 10 screws
(KDL-46S4100 ONLY)
9
Disconnect 4 connectors
10
Remove 8 screws
(KDL-46S4100 ONLY)
11
Disconnect 6 connectors
(KDL-46S4100 ONLY)
12
Remove 8 screws
(KDL-40S4100 ONLY)
13
Disconnect 6 connectors
(KDL-40S4100 ONLY)
G Board
12
A Board
9
8
Bezel
Main Bracket
Side Bracket
1
6
7
KDL-40S4100/46S4100
2
3
Main Shield
4
5
G Board
13
KDL-40S4100
1-4. TABLE-TOP STAND ASSEMBLY AND UNDER COVER REMOVAL
☛
1
Remove 4 screws
2
Remove 2 screws
1
Under Cover
Table-Top Stand Assembly
2
10
11
KDL-46S4100
Bottom Bracket
KDL-40S4100/46S4100
13
KDL-40S4100/46S4100
1-5. AC INLET AND BRACKET REMOVAL
1
Remove 1 screw
2
Remove 1 screw and release Earth Terminal
3
Remove AC Inlet from Bracket
AC Bracket
1
2
AC Inlet
1-6. STRUCTURAL FRAMES AND BRACKETS REMOVAL (KDL-40S4100 ONLY)
3
Earth Terminal
Bottom Bracket
1
Remove 1 screw from Main Bracket
2
Remove 4 screws from Main Bracket and Spine frame
3
Remove 4 screws from both Top Vesa Brackets
4
Remove 2 screws from Vesa Bracket Support
5
Remove 4 screws from both Spine Frames
6
Remove 2 screws from both Spine Frames
7
Remove 1 screw from G Board Support
8
Remove 4 screws from both Bottom Vesa Brackets
9
Remove 4 screws from Bottom Bracket
Main Bracket
1
Vesa Bracket
Support
Vesa Bracket (Top)
2
3
Spine Frame
5
4
7
6
Vesa Bracket (Bottom)
G Board Support
8
9
KDL-40S4100/46S4100
Bezel
14
1-7. STRUCTURAL FRAMES AND BRACKETS REMOVAL (KDL-46S4100 ONLY)
1
Remove 1 screw from Main Bracket
2
Remove 2 screws from Main Bracket and
Spine frame
3
Remove 2 screws from Top Vesa Bracket
4
Remove 2 screws from G Board Support 1
5
Remove 2 screws from G Board Support 2
6
Remove 2 screws from
Vesa Bracket Support
7
Remove 10 screws from Spine Frames
8
Remove 4 screws from both
Bottom Vesa Brackets
9
Remove 4 screws from Bottom Bracket
KDL-40S4100/46S4100
1
Main Bracket
2
Spine Frame
Top Vesa Bracket
4
G Board
Support 1
Vesa Bracket
Support
5
3
G Board
Suport 2
7
6
Spine Frame
Bottom Vesa Bracket
8
9
Bottom Bracket
KDL-40S4100/46S4100
Bezel
15
1-8. LOUDSPEAKER REMOVAL
1
Remove 4 screws from each speaker
KDL-40S4100/46S4100
1
Speakers
1
1-9. BOTTOM COVER, H2 BOARD, H3 BOARD AND LENS LED REMOVAL
1
Remove 2 screws
2
Disconnect 1 connector and slide out H3 (LED) Board
3
Disconnect 1 connector and remove 1 screw from H2 (IR) Board
4
Remove 4 screws
Bottom Cover
1
4
Lens LED
2
H3 (LED) Board
3
H2 (IR) Board
KDL-40S4100/46S4100
16
1-10. LCD PANEL REMOVAL
1
Disconnect 2 connectors (See Detaching the Inverter Connector Assembly)
2
Remove 2 screws
KDL-40S4100/46S4100
1
1-10-1. DETACHING THE INVERTER CONNECTOR ASSEMBLY
☛
CAUTION: Follow the instructions provided to remove the Inverter Connector Assembly
2
LCD Panel
Bezel
(1) Slide the slider to
release the
slider lock
Unlock
(2) Press the center
lock tab to
release the lock
- 4 -
(3) Gently pull the
connector up
locked state
KDL-40S4100/46S4100
17
1-10-2. ATTACHING THE INVERTER CONNECTOR ASSEMBLY
☛
CAUTION: Follow the instructions provided to reconnect the Inverter Connector Assembly.
KDL-40S4100/46S4100
(1) Hold the center
of the connector
(2) Press the center of
the connector to
insert it
(3) Slide the
slider to lock
the connector
Lock
☛
KDL-40S4100/46S4100
1-10-3. CLEANING THE LCD PANEL
CAUTION: When cleaning the TV, be sure to unplug the power cord to avoid any chance of electric shock.
1
Clean the cabinet of the TV with a dry soft cloth.
2
Wipe the LCD screen gently with a soft cloth.
Stubborn stains may be removed with a cloth slightly moistened with a solution of mild soap and warm water.
If using a chemically pretreated cloth, please follow the instruction provided on the package.
Never use strong solvents such as a thinner, alcohol or benzine for cleaning.
Periodic vacuuming of the ventilation openings is recommended to ensure to proper ventilation.
INVERTER CONNECTOR
CAUTION: Secure the Inverter Connector Assembly
by locking the housing in place as shown.
Not Locked Correctly Locked
18
1-11. BALANCER (ETC-INVERTER MT) BOARD REMOVAL
G
1
Remove 8 screws (KDL-40S4100 ONLY)
Remove 7 screws (KDL-46S4100 ONLY)
2
Pull out the board from Lamp Socket
LCD Panel
NEVER REMOVE THE
SCREWS SEC URING THE
PLASTIC S TRIP HOLD ING
THE LAMP SOC KETS
BACK LIGHT TUB ES W ILL
WARNIN
DAMAGE TO THE
OCC UR!
!
KDL-40S4100/46S4100
2
Balancer Board
(ETC-Inverter MT) Board
REMOVE SCREWS
SECURING
SHIELD
Cover
1
WARNING
NEVER REMOVE THE
SCREWS SECURING THE
PLASTIC STRIP HOLDING
THE LAMP SOCKETS
DAMAGE TO TH E
BACKLIGHT TUBES WILL
OCC UR!
!
.
Balancer (ETC-Inverter MT) Board
REMOVE
CONNECTOR AND
PULL BOARD TO
THE RIGHT
KDL-40S4100/46S4100
SHIE LD REMOVAL
END VIEW
SOCKET
BALANCER (ETC-INVERTER) BOARD REMOVAL
Only remove the screws securing the inverter
cover which may be metal or plastic. The
remaining plastic strip contains sockets for the
fluorescent backlights and should never be
loosened. The backlights will pop out of the
sockets and/or break the backlight requiring a
LCD panel replacement.
19
Loading...