Sony KDL-32XBR9, KDL-40V5100, KDL-46V5100 schematic

HISTORY INFORMATION FOR THE FOLLOWING MANUAL:
SERVICE MANUAL
MODEL NAME REMOTE COMMANDER DESTINATION
KDL-32XBR9 KDL-32XBR9 KDL-40V5100 KDL-40V5100 KDL-46V5100 KDL-46V5100
RM-YD028 MX/LATIN AMERICA
RM-YD028 US/CND
RM-YD028 MX/LATIN AMERICA
RM-YD028 US/CND
RM-YD028 MX/LATIN AMERICA
EX2R
CHASSIS
ORIGINAL MANUAL ISSUE DATE: 2/2009
: UPDATED ITEM
REVISION DATE SUBJECT
2/2009 No revisions or updates are applicable at this time. 2/2009 KDL-32XBR9 ETC-Inverter MT Board P/N added to Exploded View. Replaced page 86. 2/2009 Updated Specifi cation Section: Self-Diagnostic Function Description of LED Indicators. Replaced page 11. Updated Disassembly Section: 1-7. LCD Panel Removal. Replaced page 18. 4/2009 Updated Accessories and Packing. New AC Power Cords. Corrected Part description for Support Belt Kit and added contents. Added contents for Screw Bag Assy. Replaced page 112. 9/2009 Updated Exploded View Section to remove LCD Panel specifi c information. Replaced page 86.
LCD DIGITAL COLOR TELEVISION
9-883-812-05
Self Diagnosis
Supported model
SERVICE MANUAL
MODEL NAME REMOTE COMMANDER DESTINATION
KDL-32XBR9 KDL-32XBR9 KDL-40V5100 KDL-40V5100 KDL-46V5100 KDL-46V5100
RM-YD028 MX/LATIN AMERICA
RM-YD028 US/CND
RM-YD028 MX/LATIN AMERICA
RM-YD028 US/CND
RM-YD028 MX/LATIN AMERICA
EX2R
CHASSIS
9-883-812-05
CCDISPLAY POWER
WIDE INPUT
TOOLS
KDL-40V5100 RM-YD028
LCD DIGITAL COLOR TELEVISION
KDL-32XBR9/40V5100/46V5100

TABLE OF CONTENTS

SECTION TITLE PAGE SECTION TITLE PAGE
Specifi cations ................................................................................. 4
Warnings and Cautions - English ................................................... 6
Warnings and Cautions - French .................................................... 7
Safety-Related Component Warning .............................................. 8
Safety Check-Out ......................................................................... 10
Self-Diagnostic Function ................................................................11
SECTION 1: DISASSEMBLY ............................................................... 13
1-1. Rear Cover Removal ............................................................ 13
1-2. Switch Unit Removal ............................................................ 13
1-3. BM3 Board and Power Board Removal ............................... 14
1-4. Table-Top Stand Assembly and Under Cover Removal ....... 15
1-5. Structural Parts Removal ..................................................... 15
1-5-1. KDL-32XBR9 ........................................................... 15
1-5-2. KDL-40V5100 .......................................................... 16
1-5-3. KDL-46V5100 .......................................................... 16
1-6. Loudspeaker, Under Bar, IR Guide and
LED Guide Removal ............................................................ 17
1-7. LCD Panel Removal ............................................................. 18
1-7-1. Cleaning the LCD Panel ............................................ 18
1-8. Inverter Board Removal (KDL-32XBR9 Only) ...................... 19
WIRE DRESSING ........................................................................ 20
KDL-32XBR9 ONLY ............................................................. 20
KDL-40V5100 ONLY ............................................................ 31
KDL-46V5100 ONLY ............................................................ 42
SECTION 2: SERVICE ADJUSTMENTS ............................................. 53
2-1. Viewing Service Adjustment Data ........................................ 53
2-2. Accessing Service Mode ...................................................... 53
2-2-1. Entering the Serial Number after
changing the Main Board ......................................... 53
2-2-2. Resetting to Factory Defaults .................................. 54
SECTION 3: DIAGRAMS ..................................................................... 55
3-1. Circuit Boards Location ........................................................ 55
3-2. Printed Wiring Boards and
Schematic Diagrams Information ......................................... 55
3-3. Block Diagram ...................................................................... 57
3-4. Schematics and Supporting Information .............................. 58
BM3 Board Schematic Diagram (1 of 9) .............................. 58
BM3 Board Schematic Diagram (2 of 9) .............................. 59
BM3 Board Schematic Diagram (3 of 9) .............................. 60
BM3 Board Schematic Diagram (4 of 9) .............................. 61
BM3 Board Schematic Diagram (5 of 9) .............................. 62
BM3 Board Schematic Diagram (6 of 9) .............................. 63
BM3 Board Schematic Diagram (7 of 9) .............................. 64
BM3 Board Schematic Diagram (8 of 9) .............................. 65
BM3 Board Schematic Diagram (9 of 9) .............................. 66
G2CE Board Schematic Diagram (KDL-32XBR9 Only) ....... 68
HLR4 Board Schematic Diagram ......................................... 70
HSR Board Schematic Diagram ........................................... 72
IP1 Board Schematic Diagram (1 of 2)
(KDL-40V5100 Only) ............................................... 74
IP1 Board Schematic Diagram (2 of 2)
(KDL-40V5100 Only) ............................................... 75
IP2 Board Schematic Diagram (1 of 2)
(KDL-46VS5100 Only) ............................................. 77
IP2 Board Schematic Diagram (2 of 2)
(KDL-46V5100 Only) ............................................... 78
3-5. Semiconductors ................................................................... 81
SECTION 4: EXPLODED VIEWS ........................................................ 82
4-1. Rear Cover Assembly and Table-Top Stand Assembly ....... 82
4-2. Chassis ................................................................................ 83
4-3. Connectors (KDL-32XBR9 Only) ......................................... 84
4-4. Connectors (KDL-40V5100/46V5100 Only) ......................... 85
4-5. Bezel Assembly and LCD Panel .......................................... 86
4-6. Screw Legend ...................................................................... 87
KDL-32XBR9/40V5100/46V5100
SECTION 5: ELECTRICAL PARTS LIST ............................................ 88
APPENDIX A: ENCRYPTION KEY COMPONENTS ..........................A-1
3

SPECIFICATIONS

y
KDL-32XBR9/40V5100/46V5100
Power Requirements
Power Consumption (W)
In Use (Max)
In Standby
120V AC, 60Hz
120W (KDL-32XBR9 only) 200W (KDL-40V5100 only) 245W (KDL-46V5100 only)
Less than 1 W
VIDEO (IN) 1/2: S Video (4-Pin Mini DIN (VIDEO 2 Only) Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative
C: 0.286 Vp-p (Burst signal), 75 ohms
Video
1 Vp-p, 75 ohms unbalanced, sync negative
Audio
500 mVrms (Typical) Impedance:47 kilohms
COMPONENT IN 1/2: YP
(Component Video)
BPR
Y:1.0 Vp-p, 75 ohms unbalanced, sync negative PB:0.7 Vp-p, 75 ohms PR:0.7 Vp-p, 75 ohms Signal format: 480i, 480p, 720p, 1080i, 1080p
AUDIO
500 mVrms (Typical) Impedance: 47 kilohms
HDMI IN 1/2/3/4: HDMI: Video: 480i, 480p, 720p, 1080i,1080p, 1080/24p
Audio: Two channel linear PCM 32, 44.1 and 48 kHz, 16, 20 and 24 bits
AUDIO
500 mVrms (Typical) Impedance: 47 kilohms
AUDIO OUT: 500 mVrms (Typical)
DIGITAL AUDIO OUT (OPTICAL): PCM optical signal
PC IN: D-sub 15-pin, analog RGB, 0.7 Vp-p, 75 ohms, positive
PC AUDIO INPUT: Stereo mini jack, 500 mVrms (Typical) Impedance: 47 kilohms
Licensing Information
Macintosh is a trademark of Apple Inc., registered in the U.S. and other countries.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.
Fergason Patent Properties, LLC: U.S. Patent No. 5,717,422 U.S. Patent No. 6,816,141
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
TruSurround XT, SRS and (z) symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.
Blu-ray Disc is a trademark.
“BRAVIA”, , BRAVIA Sync and are trademarks or registered trademarks of Sony Corporation.
“PLAYSTATION” is a registered trademark and “PS3” is a trademark of
Computer Entertainment Inc.
Son
KDL-32XBR9/40V5100/46V5100
Design and specifi cations are subject to change without notice.
4
Speaker Output
1/2
7/8
3/4
1/4
1/2
3/4
Speaker/Full Range (2)
mm
in
Dimensions (W x H x D)
with stand
mm 798 x 584 x 227 mm 987 x 684 x 271 mm 1,123 x 772 x 323 mm
in
without stand
mm 798 x 537 x 89 mm 987 x 638 x 93 mm 1,123 x 725 x 96 mm
in
wall-mount hole pattern (mm) 200 x 200
wall-mount screw size (mm)
Mass
with stand
kg 13.4 kg 18.6 kg 25.5 kg
lbs 29.6 lbs 41.0 lbs 56.2 lbs
without stand
kg 12.2 kg 16.9 kg 22.6 kg
lbs 26.9 lbs 37.3 lbs 49.8 lbs
x 23 x 9 in 38
31
1/2
1/4
31
x 21
5/8
x 3
in 38
10 W+ 10 W
35 X 175
7/16
x 7
1
x 27 x 10
7/8
1/8
x 25
x 3
M6 x 8-12 mm
in 44
3/4
in 44
300 x 300
All measurements are approximations.
KDL-32XBR9/40V5100/46V5100
KDL-46V5100KDL-40V5100KDL-32XBR9
x 30
x 12
in
1/4
5/8
x 3
7/8
in
x 29
Television system
NTSC American TV Standard ATSC (8VSB terrestrial) ATSC compliant 8VSB QAM on cable ANSI/SCTE 07 2000
Channel coverage
Analog 2-69 Terrestrial 1-135 Cable Digital 2-69 Terrestrial 1-135 Cable
Antenna
75-ohm external terminal for RF inputs
Panel System
LCD (Liquid Crystal Display) Panel
Display Resolution (horizontal x vertical)
1,920 dots x 1,080 lines
Screen Size (measured diagonally)
~ 31.5” (KDL-32XBR9 only) ~ 40” (KDL-40V5100 only) ~ 46” (KDL-46V5100 only)
Supplied Accessories
Remote Commander RM-YD028 Two Size AA (R6) Batteries Cable Holder (1 attached to the TV) Operating Instructions Quick Setup Guide Warranty Card Safety and Regulatory Booklet Attaching the Table-Top Stand Flyer Screws (4)
Optional Accessories
Connecting Cables Wall-Mount Bracket SU-WL500
KDL-32XBR9/40V5100/46V5100
5
KDL-32XBR9/40V5100/46V5100

WARNINGS AND CAUTIONS - ENGLISH

CAUTION
These servicing instructions are for use by qualifi ed service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualifi ed to do so.
CARRYING THE TV
Be sure to follow these guidelines to protect your property and avoid causing serious injury.
• Carry the TV with an adequqate number of people; larger size TVs require two or more people.
• Correct hand placement while carrying the TV is very important for safety and to avoid damages.
WARNING!!
An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis. The chassis of this receiver is directly connected to the ac power line.
! SAFETY-RELATED COMPONENT WARNING!!
Components identifi ed by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identifi ed in this manual. Follow these procedures whenever critical components are replaced or improper operation is suspected.
KDL-32XBR9/40V5100/46V5100
6
KDL-32XBR9/40V5100/46V5100

WARNINGS AND CAUTIONS - FRENCH

ATTENTION!!
Ces instructions de service sont à l’usage du personnel de service qualifi é seulement. Pour prévenir le risque de choc électrique, ne pas faire l’entretien autre que celui contenu dans le Mode d’emploi à moins que vous soyez qualifi é faire ainsi.
POUR TRANSPORTER LE TÉLÉVISEUR
Tenez compte de ce qui suit pendant l’installation du téléviseur :
• Débranchez tous les câbles avant de transporter le téléviseur.
• Transportez le téléviseur avec le nombre de personnes approprié ; un téléviseur de grande taille doit être transporté par au moins deux personnes.
• Lors du transport du téléviseur, l’emplacement des mains est très important pour votre sécurité, ainsi que pour éviter de causer des dommages.
ALERTE!!
Afi n d’eviter tout risque d’electrocution provenant d’un chássis sous tension, un transformateur d’isolement doit etre utilisé lors de tout dépannage. Le chássis de ce récepteur est directement raccordé à l’alimentation du secteur.
! ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!
Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont d’une importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance est critique pour la securite du fonctionnement sont identifi es dans le present manuel. Suivre ces procedures lors de chaque remplacement de composants critiques, ou lorsqu’un mauvais fonctionnement suspecte.
KDL-32XBR9/40V5100/46V5100
7

SAFETY-RELATED COMPONENT WARNING

KDL-32XBR9/40V5100/46V5100
There are critical components used in LCD color TVs that are important for safety. These components are identifi ed with shading and mark on the schematic diagrams and the electrical parts list. It is essential that these critical parts be replaced only with the part number specifi ed in the electrical parts list to prevent electric shock, fi re, or other hazard.
NOTE: Do not modify the original design without obtaining written permission from the manufacturer or you will void the original parts and labor guarantee.
!
USE CAUTION WHEN HANDLING THE LCD PANEL
When repairing the LCD panel, be sure you are grounded by using a wrist band.
When installing the LCD panel on a wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.
To avoid damaging the LCD panel:
do not press on the panel or frame edge to avoid the risk of electric shock. do not scratch or press on the panel with any sharp objects. do not leave the module in high temperatures or in areas of high humidity for an extended period of time. do not expose the LCD panel to direct sunlight. avoid contact with water. It may cause a short circuit within the module. disconnect the AC adapter when replacing the backlight (CCFL) or inverter circuit.
(High voltage occurs at the inverter circuit at 650Vrms.)
always clean the LCD panel with a soft cloth material. use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short. protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).
LEAKAGE CURRENT HOT CHECK CIRCUIT
KDL-32XBR9/40V5100/46V5100
8
The circuit boards used in these models have been processed using Lead Free Solder. The boards are identified by the LF logo located close to the board designation e.g. H1 etc [ see example ]. The servicing of these boards requires special precautions to be taken as outlined below.
KDL-32XBR9/40V5100/46V5100
example 1
It is strongly recommended to use Lead Free Solder material in order to guarantee optimal quality of new solder joints. Lead Free Solder is available under the following part numbers :
rebmuntraP retemaiD skrameR
91-500-046-7mm3.0gK52.0
02-500-046-7mm4.0gK05.0
12-500-046-7mm5.0gK05.0
22-500-046-7mm6.0gK52.0
32-500-046-7mm8.0gK00.1
42-500-046-7mm0.1gK00.1
52-500-046-7mm2.1gK00.1
62-500-046-7mm6.1gK00.1
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics.
For more information on the use of Lead Free Solder, please refer to
http://www.sony-training.com
KDL-32XBR9/40V5100/46V5100
9

SAFETY CHECK-OUT

KDL-32XBR9/40V5100/46V5100
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instructions.
2. A battery-operated AC milliampmeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low voltage scale. The Simpson’s 250 and Sanwa SH-63TRD are examples of passive VOMs that are suitable. Nearly all battery-operated digital multimeters that have a 2 VAC range are suitable (see Figure A).
How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground; the cover-plate retaining screw on most AC outlet boxes is also at earth ground. If the retaining screw is to be used as your earth ground, verify that it is at ground by measuring the resistance between it and a cold-water pipe with an ohmmeter. The reading should be zero ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble- light (not a neon lamp) between the hot side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side on the line; the lamp should light at normal brilliance if the screw is at ground potential (see Figure B).
Leakage Test
0.15 F
Figure A. Using an AC voltmeter to check AC leakage. Figure B. Checking for earth ground.
To Exposed Metal Parts on Set
Earth Ground
AC Voltmeter (0.75V)
Trouble Light
AC Outlet Box
Ohmmeter
Cold-water Pipe
KDL-32XBR9/40V5100/46V5100
10
KDL-32XBR9/40V5100/46V5100

SELF-DIAGNOSTIC FUNCTION

The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED indicator will automatically begin to fl ash. The number of times the LED fl ashes translates to a probable source of the problem. A defi nition of the STANDBY LED fl ash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the Remote Commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
1. Diagnostic Test Indicators
When an error occurs, the STANDBY LED indicator will fl ash a set number of times to indicate the possible cause of the problem. If there is more than one error, the indicator will identify the fi rst of the problem areas.
LED Indicators
PIC OFF / TIMER
STANDBY
POWER
Self Diagnosis
Supported model
Description of LED Indicators
POWER LED
STANDBY LED
PIC OFF/ TIMER LED
LED LED Type Description
Green LED
Red LED
* Lights up in green when the TV set is turned on.
* Lights up in red when function PC Power Management is activated and there is no signal received while in the PC input.
* If LED blinks continuously, this may indicate that the TV needs servicing.
* Lights up in amber when the Timer or Sleep functions
Green or Amber
LED
are set. When the timer is set this LED will remain lit even if the TV is turned off. * Lights up in green whe the Backlight feature is activated to Off.
2 times
5 times
LED ON 0.3 sec.
LED OFF 0.3 sec.
LED OFF
3 sec.
KDL-32XBR9/40V5100/46V5100
11
LED Indicators
p
KDL-32XBR9/40V5100/46V5100
Diagnostic Item
Descri
tion
Main Power 2 times
DC Alert1 3 times
TCON Error 4 times LCD Panel
HDMI 5 times BM3 (Main) Board
Backlight 6 times LCD Panel
Temp 7 times BM3 (Main) Board
HFR Error 8 times LCD Panel
Viewing the Self Check Diagnostic List
1. TV must be in standby mode. (Power off).
2. Press the following buttons on the Remote Commander within a second of each other:
DISPLAY
The Self Check list displays.
NOTE: This is the same as accessing Service Adjustments.
The
displays.
Channel 5 Volume +
logo displays momentarily, then the Service Mode list
Number of times
STANDBY lamp flashes
TV POWER
.
Power Supply Board G2CE Board (KDL-32XBR9 ONLY) IP1 Board (KDL-40V5100 ONLY) IP2 Board (KDL-46V5100 ONLY) BM3 (Main) Board Power Supply Board G2CE Board (KDL-32XBR9 ONLY) IP1 Board (KDL-40V5100 ONLY) IP2 Board (KDL-46V5100 ONLY)
3. To display the Self Diagnostic list, press
Service/ADC Auto Calibration
Version: ER2.6-C121 DTT: S255.P033.S077 Model: 40V5100 Serial : 8000016 Power on Time: 00000H
Diagnostic and Serial Update
ADC Auto Calibration Clone User Setting Direct Log to USB Factory Default
Change Back Exit
RETURN
4. To exit Service Mode, press .
Possible Location
.
Service Mode/Product Information
Version: ER2.6-C121 DTT: S255.P033.S077 Model: 40V5100 Power on Time: 00000H
Serial :
Diagnostic Information
2-MAIN POWER: 1
3-DC ALERT1: 0
8000016
1 indicates an error was detected 0 indicates no error was detected
4-TCON: 0 5-HDMI:
0
6-Backlight: 0 7-TEMP: 0 8-HFR: 0 101-WDT: 0
Change Back Exit
RETURN
KDL-32XBR9/40V5100/46V5100
12

1-1. REAR COVER REMOVAL

1
Remove 15 screws from Rear Cover
(KDL-32XBR9 Only)
Remove 18 screws from Rear Cover
(KDL-40V5100 Only)
Remove 20 screws from Rear Cover
(KDL-46V5100 Only)
2
Remove 1 screw from Side Jack position
3
Remove 1 screw from Terminal position
Remove 2 screws from Rear Cover
4
(KDL-32XBR9 Only)
Remove 4 screws from Rear Cover
(KDL-40V5100/46V5100 Only)
5
The Rear Cover is attached to the
Bezel Assembly with three small tabs. Use caution when removing the Rear Cover to avoid damage to these tabs

SECTION 1: DISASSEMBLY

5
Ta b Inserts
Bezel
KDL-32XBR9/40V5100/46V5100
Rear Cover
1
Screw, +BVTP2 4X16
2
Screw, +BVTP 3X12 TYPE2 IT-3
Screw,
3
+BVTP 3X12 TYPE2 IT-3

1-2. SWITCH UNIT REMOVAL

1
Slide out Switch unit from Bezel
2
Disconnect 1 connector from HSW3 Board
Bezel
4
Screw, +PSW M4X8 (32) Screw, +PSW M4X12 (40/46)
KDL-32XBR9/40V5100/46V5100
1
2
Switch Unit (Contains HSW3 Board)
13

1-3. BM3 BOARD AND POWER BOARD REMOVAL

1
Unhook Side Jack Cover from Main Bracket
2
Disconnect 5 connectors from BM3 Board
3
Remove 9 screws from BM3 Board
4
Disconnect 5 connectors from IP2 Board (KDL-46V5100 Only)
5
Remove 6 screws from IP2 Board (KDL-46V5100 Only)
6
Disconnect 5 connectors from IP1 Board (KDL-40V5100 Only)
7
Remove 5 screws from IP1 Board (KDL-40V5100 Only)
8
Disconnect 3 connectors from G2CE Board (KDL-32XBR9 Only)
9
Remove 6 screws from G2CE Board (KDL-32XBR9 Only)
Main Bracket
2
Side Jack Cover
1
KDL-32XBR9/40V5100/46V5100
9
Screw,
+BVST 3X6
8
G2CE BOARD
KDL-32XBR9 ONLY
5
Screw,
+BVST 3X6
8
Screw,
+BVST 3X6
3 Screw,
+BVST 3X6
BM3 Board
4
IP2 BOARD
KDL-46V5100 ONLY
6
IP1 BOARD
KDL-40V5100 ONLY
KDL-32XBR9/40V5100/46V5100
14

1-4. TABLE-TOP STAND ASSEMBLY AND UNDER COVER REMOVAL

1
Remove 4 screws from Table-Top Stand Assembly
2
Remove Under Cover from Bottom Frame
1 Screw,
+PSW M5X12
Table-Top
Stand Assembly
KDL-32XBR9/40V5100/46V5100
Under Cover

1-5. STRUCTURAL PARTS REMOVAL

1-5-1. KDL-32XBR9
Remove 1 screw from Main Bracket and Bezel
1
Remove 2 screws from Spine (L)
2
Remove 2 screws from Spine (R)
3
Remove 2 screws from Bottom Frame
4
Remove 2 screws from Bottom Frame
5
2
Bottom Frame
1 Screw,
+BVTP 3X12 TYPE2 IT-3
Screw,
2
+PSW M4X8
Spine (L)
Screw,
3
+PSW M4X8
KDL-32XBR9/40V5100/46V5100
Main Bracket
Spine (R)
Screw,
4
+BVTP2 4X16
Screw,
5
+PSW M4X8
Bottom Frame
15
1-5-2. KDL-40V5100
Remove 1 screw from Main Bracket and Bezel
1
Remove 4 screws from Spine (L)
2
Remove 2 screws from IP1 Frame
3
Remove 4 screws from Spine (R)
4
Remove 3 screws from Bottom Frame
5
1 Screw,
+BVTP 3X12 TYPE2 IT-3
Main Bracket
2 Screw,
+PSW M4X8
Spine (L)
IP1 Frame
KDL-32XBR9/40V5100/46V5100
4 Screw,
+PSW M4X8
1-5-3. KDL-46V5100
Remove 1 screw from Main Bracket and Bezel
1
Remove 3 screws from Spine (L)
2
Remove 1 screw from G Frame
3
Remove 2 screws from Center Frame
4
Remove 3 screws from Spine (R)
5
Remove 3 screws from Bottom Frame
6
Remove 1 screw from Bottom Frame
7
Spine (L)
3 Screw,
+BVST 3X6
1 Screw,
+BVTP 3X12 TYPE2 IT-3
Main Bracket
2 Screw,
+PSW M5X8
G Frame
Spine (R)
Bottom Frame
5 Screw,
+BVTP2 4X16
3 Screw,
+BVST 3X6
4 Screw,
+PSW M5X8
5 Screw,
+PSW M5X8
KDL-32XBR9/40V5100/46V5100
Center Frame
Spine (R)
7 Screw,
+PSW M5X8
6 Screw,
+BVTP2 4X16
Bottom Frame
16

1-6. LOUDSPEAKER, UNDER BAR, IR GUIDE AND LED GUIDE REMOVAL

Slide out both Speakers from Bezel
1
Remove 1 screw from Under Bar
2
Disconnect 1 connector from HLR4 Board and release from LED Guide
3
Unhook and release LED Guide from Bezel
4
Disconnect 1 connector from HSR Board and release from IR
5
Unhook and release IR from Bezel
6
5
HSR Board
KDL-32XBR9/40V5100/46V5100
Speaker
1
2 Screw,
Under Bar
+BVTP2 4X16
Bezel
IR Guide
Bezel
6
HLR4 Board
LED Guide
4
3
Speaker
1
KDL-32XBR9/40V5100/46V5100
17

1-7. LCD PANEL REMOVAL

CAUTION: When replacing the LCD Panel, you must also replace the Radiation sheet. For part number information, refer to the Exploded View section of this manual.
Remove LVDS connector and LVDS holder from T-CON and LCD panel
1
Remove 2 screws and release LCD panel from Bezel
2
Disconnect 1 connector from Inverter Board
3
(KDL-32XBR9 Only)
Disconnect 2 connectors from Balancer Board
(KDL-40/46V5100 Only)
Remove 2 screws and detach Heat Sink
4
from LCD Panel (KDL-32XBR9 Only)
Remove 3 screws and detach Heat Sink
from LCD Panel (KDL-40V5100/46V5100 Only)
Gently remove Radiation Sheet
5
CAUTION: The LVDS cable can Only be installed one way determine which side is attached to the TCON and which side is attached to the BM3 Board.
. There is colored tape on the cable to
Insulating Sheet (IP2) Detail
4 Screw,
+PSW M3X8
Double Sided Tape
KDL-46V5100 ONLY
1
KDL-32XBR9/40V5100/46V5100
Insulating Sheet (IP1) Detail
Double Sided Tape
KDL-40V5100 ONLY
2 Screw,
+BVTP2 4X16
3
Heat Sink
Radiation Sheet
5
1-7-1. CLEANING THE LCD PANEL
CAUTION: When cleaning the TV, be sure to unplug the power cord to avoid any chance of electric shock.
Clean the cabinet of the TV with a dry soft cloth.
Wipe the LCD screen gently with a soft cloth.
Stubborn stains may be removed with a cloth slightly moistened with a solution of mild soap and warm water.
If using a chemically pretreated cloth, please follow the instruction provided on the package.
Never use strong solvents such as a thinner, alcohol or benzine for cleaning.
Periodic vacuuming of the ventilation openings is recommended to ensure to proper ventilation.
LCD Panel
Bezel
KDL-32XBR9/40V5100/46V5100
18
1-8. INVERTER BOARD REMOVAL (KDL-32XBR9 ONLY)
Remove 6 screws from Inverter Board Cover
1
2
Slide out Inverter Board from Light Sockets
LCD Panel
1
KDL-32XBR9/40V5100/46V5100
2
2
Inverter Board
Cover
KDL-32XBR9/40V5100/46V5100
19
20
KDL-32XBR9/40V5100/46V5100
KDL-32XBR9/40V5100/46V5100

WIRE DRESSING

CONNECTION PLACEMENT
epatbafoC1
teksaG2
)5198.oN(epaT
mm06xmm52
31
epatbafoC
pmalc T
noitpircseD
3
1
gnisserd ni lobmyS
tnemucod
ytQ
INSERT THE GASKET OVER THE
1
2
epatbafoC1
teksaG2
)5198.oN(epaT
mm06xmm52
31
epatbafoC
pmalc T
noitpircseD
3
1
gnisserd ni lobmyS
tnemucod
ytQ
gnihcuot renut no epatbafoc ddA
redloh tekcarb niam eht
epatbafoC draob 3MB fo renut no
b TapeafoC
3MB
draob
redloh tekcarb niaM
1
23
epatbafoC1
teksaG2
)5198.oN(epaT
mm06xmm52
31
epatbafoC
pmalc T
noitpircseD
3
1
gnisserd ni lobmyS
tnemucod
ytQ
elbaC SDVL 2019NC/3MB ot NOCT morf elbaC SDVL 2019NC/3MB ot NOCT morf
decalp eb ot tsrif eht eb lliw elbac SDVL ehT
lenap ot etacidnI epat deR
edis NOCT
1
tnioP noituaC
htiw demmaj parT diovA
egde yna hcuot ro latem
elbac eht sserts oN
neewteb elbac esool peeK
sepat dna srotcennoc
eht revo talf sepaT peeK
elbac
:snoitacidnI
,elbac SDVL tcennoC- deR
rehto dna NOCT ot DI epat
.)3MB( 2019NC ot edis
1 pmalC elbaC tresnI-
dna sepaT ddA-
elbaC SDVL
NOCT
2019NC/3MB
epaT
tekcarb rednu
pmalC
1
1
bafoC
gnidloh ylno epat
1
1

epatbafoC1
teksaG2
)5198.oN(epaT
mm06xmm52
31
epatbafoC
pmalc T
noitpircseD
3
1
gnisserd ni lobmyS
tnemucod
ytQ
elbaC
ot recnalaB morf 4001NC/3MB dna 1026NC/2G
4001NC
1026NC
recnalaB
2
2
:snoitacidnI
yb gnikat 2 epat ddA
senil lenap ecnerefer
2G
3MB
epaT
pmalC

25
epatbafoC1
teksaG2
)5198.oN(epaT
mm06xmm52
31
epatbafoC
pmalc T
noitpircseD
3
1
gnisserd ni lobmyS
tnemucod
ytQ
elbaC 3001NC/3MB dna 2026NC/2G morf
3001NC
1026NC
2G
3MB

26
epatbafoC1
teksaG2
)5198.oN(epaT
mm06xmm52
31
epatbafoC
pmalc T
noitpircseD
3
1
gnisserd ni lobmyS
tnemucod
ytQ
elbaC tinu hctiwS dna 4RLH ,RSH ot 4003NC/3MB morf elbaC
slanimret srekaepS ot 0002NC/3MB morf
:snoitacidnI
tinu hctiwS dna sdraob s’H ot elbac eht tcennoC-
lanimret srekaeps thgir dna tfel ot elbac eht tcennoC-
)ecnerefer sa enil dehsad ekat (lenap fo retnec ta epat eulb etacol , ssenrah retnec oT-
erutcip ni wohs sa )sepat kcalB( sepat htob etacol , ssenrah retnec oT-
sredils txen eht ni wohs sa sepat ecalP-
RSH
4RLH
0002NC
4003NC
hctiwS
tinu
retnec :tniop noituaC
tfel eht ot detfihs ecnerefer
mm5
3MB
0002NC
4003NC
 
 
epatbafoC1
teksaG2
)5198.oN(epaT
mm06xmm52
31
epatbafoC
pmalc T
noitpircseD
3
1
gnisserd ni lobmyS
tnemucod
ytQ
elbaC
tinu hctiwS dna 4RLH ,RSH ot 4003NC/3MB morf
elbaC
slanimret srekaepS ot 0002NC/3MB morf
5
3
4
tinu hctiwS
eht rednu ssorc llahs elbac ehT
egde lenap
:snoitacidnI
detcennoc eb llahs selbac ehT-
draob 4RLH dna tinu hctiws ot
lanogaid ni 4 dna 3 epat ddA-
segde prahs lenap revoc ot
yb gnikat 5 epat tresnI-
.enil tod eht ecnerefer
4RLH
5
3
4
KPS R
KPS R
28
epatbafoC1
teksaG2
)5198.oN(epaT
mm06xmm52
31
epatbafoC
pmalc T
noitpircseD
3
1
gnisserd ni lobmyS
tnemucod
ytQ
elbaC
tinu hctiwS dna 4RLH ,RSH ot 4003NC/3MB morf
elbaC
slanimret srekaepS ot 0002NC/3MB morf
01
21
6
11
7
8
9
4003NC
0002NC
RSH
3MB
RSH
:snoitacidnI
ecnerefer yb gnikat 11 dna 6 epat tresnI-
.enil tod eht
nidloh 7 epat ddA- selbac htob g
ni 01 dna 9 ,8 epat ddA- revoc ot lanogaid
rb niam dna lenap segde prahs tekca
ekcarb ni 21 epat ddA- prahs revoc ot t
egde
KPS L
9
0002NC

29
epatbafoC1
teksaG2
)5198.oN(epaT
mm06xmm52
31
epatbafoC
pmalc T
noitpircseD
3
1
gnisserd ni lobmyS
tnemucod
ytQ
elbaC 3MB wercs ot 2G wercS
2G
3MB
epaT
31

30
epatbafoC1
teksaG2
)5198.oN(epaT
mm06xmm52
31
epatbafoC
pmalc T
noitpircseD
3
1
gnisserd ni lobmyS
tnemucod
ytQ
droc CA
1016NC/2G
mm 09
redloH CA
noitisop
droc CA
2G
1016NC
pmalC
3
Loading...
+ 84 hidden pages