Sony KDL-32E4000, KDL-46W42xx, KDL-32E40xx, KDL-26V47xx, KDL-32V4700 User Manual

...
LCD Digital Colour TV
Operating Instructions
For useful information about Sony products
Printed in Spain
3-298-243-11(1)
U
KDL-52W40xx
KDL-52W42xx
KDL-46W40xx
KDL-46W42xx
KDL-40W40xx
KDL-40W42xx
KDL-32W40xx
KDL-32W42xx
U
© 2008 Sony Corporation 3-298-243-11(1)
NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM
A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 10 AMP fuse approved by ASTA or BSI to BS 1362 (i.e., marked with or ) must be used. When an alternative type of plug is used it should be fitted with a 10 AMP FUSE otherwise the circuit should be protected by a 10 AMP FUSE at the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
FUSE
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and replace the fuse. Please refer to the illustration that actually equiped with the product.
Introduction
Thank you for choosing this Sony product. Before operating the TV, please read this manual thoroughly and retain it for future reference
Disposal of the TV set
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the
equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.
negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance
recycling of electrical and electronic
Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems)
This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. By ensuring these batteries are disposed of correctly, you will help prevent potentially
or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.
The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.
Notice for Digital TV function
• Any functions related to Digital TV ( ) will only work in countries or areas where DVB-T (MPEG2 and MPEG4 AVC) digital terrestrial signals are broadcast or where you have access to a compatible DVB-C (MPEG2 and MPEG4 AVC) cable service. Please confirm with your local dealer if you can receive a DVB-T signal where you live or ask your cable provider if their DVB-C cable service is suitable for integrated operation with this TV.
• The cable provider may charge an additional fee for such a service and you may be required to agree to their terms and conditions of business.
• Although this TV set follows DVB-T and DVB-C specifications, compatibility with future DVB-T digital terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.
• Some Digital TV functions may not be available in some countries/regions and DVB-C cable may not operate correctly with all providers.
• For more information about DVB-C functionality please see our cable support site: http://support.sony-europe.com/TV/DVBC
/
Trademark information
is a registered trademark of the DVB Project
• Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under one or more of the following US patents: 5510752, 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.
• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI Licensing LLC.
A
ViV
HD3D Sound
~
• The illustrations used in this manual are of the KDL-40W4000 unless otherwise state.
• The "x" that appear on the model name, correspond to numeric digits related to colour variation.
GB
2
Table of Contents
Start-up Guide 4
Start-up Guide 4
Checking the accessories.................................................................................................... 4
Safety information................................................................................................................ 9
Precautions........................................................................................................................ 10
Overview of the remote ................................................................................................... 11
Overview of the TV buttons and indicators................................................................... 12
Watching TV
Watching TV....................................................................................................................... 13
Checking the Guide .................................................................................................. 15
Using the Digital Favourite list .................................................................................. 16
Using Optional Equipment
Connecting optional equipment.......................................................................................... 17
Viewing pictures from connected equipment ..................................................................... 18
Using BRAVIA Sync (Control for HDMI) ............................................................................ 19
Using MENU Functions
Overview of the TV Home Menu (XMB™)......................................................................... 21
Settings.............................................................................................................................. 22
Picture .......................................................................................................................... 22
Sound ........................................................................................................................... 23
Features .......................................................................................................................24
Set-up ........................................................................................................................... 25
Analogue Set-up .......................................................................................................... 28
Digital Set-up ..................................................................................................... 29
Photo ................................................................................................................................. 32
Picture Frame ............................................................................................................... 32
USB Photo Viewer ....................................................................................................... 32
Additional Information
Specifications..................................................................................................................... 33
Troubleshooting .................................................................................................................36
: for digital channels only
Before operating the TV, please read the “Safety information” section of this manual. Retain this manual for future reference.
GB
GB
3
Start-up Guide
1: Checking the accessories
Mains lead (1) (only for KDL-52W4xxx, KDL­46W4xxx, KDL-40W4xxx, KDL-40E4xxx)
Remote RM-ED011 (1) Remote RM-ED011 W (1) (only for KDL-
40E4xxx, KDL-32E4xxx, KDL-26E4xxx) Size AA batteries (R6 type) (2) Stand (1) (except for KDL-52W4xxx,
KDL-26E4xxx) Screws for stand (4) (only for KDL-
46W4xxx, KDL-40W4xxx, KDL-40E4xxx, KDL-37V4xxx)
Screws for stand (3) (only for KDL­32W4xxx, KDL-32E4xxx, KDL-32V4xxx, KDL-26V4xxx)
To insert batteries into the remote
Push and lift the cover to open.
2: Attaching the stand
(except for KDL-52W4xxx, KDL-26E4xxx)
1 Open the carton box and take out the stand
and the screws.
~
• Observe the correct polarity when inserting batteries.
• Do not use different types of batteries together or mix old and new batteries.
• Dispose of batteries in an environmentally friendly way. Certain regions may regulate disposal of batteries. Please consult your local authority.
• Handle the remote with care. Do not drop or step on it, or spill liquid of any kind onto it.
• Do not place the remote in a location near a heat source, a place subject to direct sunlight, or a damp room.
GB
4
2 Place the TV set on the stand. Take care not to
C
interfere with cables.
3: Connecting an aerial/VCR/ DVD recorder
Start-up Guide
onnecting an aerial/cable
Terrestrial signal
or cable
Coaxial cable
3 Fix the stand to the TV using the supplied
screws.
KDL-46W4xxx KDL-40W4xxx KDL-40E4xxx KDL-37V4xxx
KDL-32W4xxx KDL-32E4xxx KDL-32V4xxx KDL-26V4xxx
Connecting an aerial/ cable/ VCR/ DVD recorder
~
If using an electric screwdriver, set the tightening torque at approximately 1.5 N·m (15 kgf·cm)
Scart lead
Coaxial cable
Terrestrial signal
or cable
Coaxial cable
VCR/ DVD recorder
GB
5
4: Preventing the TV
7:
Performing the initial
from toppling over
1 Install a wood screw (4 mm in diameter, not
supplied) in the TV stand.
2 Install a machine screw (M5 x 12, not
supplied) into the screw hole of the TV.
3 Tie the wood screw and the machine screw
with a strong cord.
5: Connecting the cables
set-up
GUIDE
3,4,5
KDL-52W4xxx KDL-46W4xxx KDL-40W4xxx KDL-40E4xxx
6: Bundling the cables
GB
6
1 Connect the TV to your mains socket
(220-240V AC, 50Hz).
2 Press 1 on the TV.
When you switch on the TV for the first time, the Language menu appears on the screen.
3 Press F/f/G/g to select the language
displayed on the menu screens, then press .
Language
English
Nederlands
Français
Italiano
Deutsch
Türkçe
Español
Català
Português
Polski
Set
Česky
Magyar
Русский
Б
Б
лгар
Suomi
Dansk
Svenska
Norsk
Slovenčina
Română
ски
Analogue
Back
4
Press F/f to select the country/region in which you will operate the TV, then press .
Country
Set
-
United Kingdom
Ireland
Nederland
België/Belgique
Luxembourg
France
Italia
Schweiz/Suisse/Svizzera
Deutschland
Analogue
Back
If the country/region in which you want to use the TV does not appear in the list, select “-” instead of a country/region.
5 Press F/f to select the location type in which
you will operate the TV, then press .
~
Sony recommends you to select “Home” for power saving.
Location
Home
Shop
Analogue
The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, so do not press any buttons on the TV or remote while proceeding.
If a message appears for you to confirm the aerial connection
No digital or analogue channels were found. Check all the aerial/cable connection and then press to start auto-tuning again.
3 When the Programme Sorting menu appears
on the screen, follow the steps of “Programme Sorting”(page 28).
If you do not change the order in which the analogue channels are stored on the TV, press
RETURN to go to step 4.
4
Quick Start
Do you want to enable Quick Start?
TV turns on mo re quickly but st andby power
consumption is increased.
Yes No
Analogue
Start-up Guide
Set
This option selects the initial picture mode appropriate for the typical lighting condition in these enviroments.
8: Auto-tuning the TV
1 Select OK then press .
Auto Tuning
Do you want to start Auto Tuning?
OK Cancel
Set
2 Press F/f to select “Antenna” or “Cable”,
then press .
If you select “Cable”, the screen for selecting the scan type appears. See “To tune the TV for Cable connection” (page 8).
Analogue
Set
Back
For details, see page 24.
Back
5
Control for HDMI
Set
Do you want to enable control for compatible
HDMI devices?
Yes No
Analogue
Back
For details, see page 19.
6 Press .
The TV has now tuned in all the available channels.
~
When a digital broadcast channel cannot be received, or when selecting a region in which there are no digital broadcasts in step 3 (page 7), the time must be set after
Back
performing step 3.
GB
7
To tune the TV for Cable connection
1 Press . 2 Press F/f to select “Quick Scan” or “Full
Scan”, then press .
"Quick Scan" : channels are tuned according to the cable operator information within the broadcast signal. Recommended setting for "Frequency", "Network ID" and "Symbol Rate" is "Auto". This option is recommended for fast tuning when supported by your cable operator. If the "Quick Scan" does not tune, please use the "Full Scan" method below. "Full Scan" : All available channels are tuned and stored. This procedure may take some time. This option is recommended when "Quick Scan" is not supported by your cable provider. For further information about supported cable providers, refer to support web site: http://support.sony-europe.com/TV/DVBC/
3 Press f to select “Start”, then press .
The TV starts searching for channels. Do not press any buttons on the TV or remote.
~
Some cable providers do not support “Quick Scan”. If no channels are detected using “Quick Scan”, perform “Full Scan”.
Detaching the Table­Top Stand from the TV
~
Do not remove the Table-Top Stand for any reason other than to wall-mount the TV.
KDL-52W4xxx KDL-46W4xxx KDL-40W4xxx KDL-40E4xxx KDL-37V4xxx
KDL-26E4xxx
KDL-32W4xxx KDL-32E4xxx KDL-32V4xxx KDL-26V4xxx
GB
8
Safety information
Installed on the wall
30 cm
Installation/Set-up
Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries.
Installation
• The TV set should be installed near an easily accessible mains socket.
• Place the TV set on a stable, level surface.
• Only qualified service personnel should carry out wall installations.
• For safety reasons, it is strongly recommended that you use Sony accessories, including:
- KDL-52W40xx/ KDL-52W42xx/ KDL-46W40xx/
KDL-46W42xx/ KDL-40W40xx/ KDL-40W42xx/ KDL-32W40xx/ KDL-32W42xx/ KDL-40E40xx/ KDL-32E40xx/ KDL-37V45xx/ KDL-37V47xx/
KDL-32V45xx/ KDL-32V47xx:
Wall-Mount Bracket SU-WL500.
- KDL-26V45xx/ KDL-26V47xx / KDL-26E40xx:
Wall-mount Bracket SU-WL100.
- KDL-46W40xx/ KDL-46W42xx/ KDL-40W40xx/
KDL-40W42xx/KDL-32W40xx/ KDL-32W42xx/ KDL-40E40xx/ KDL-32E40xx/ KDL-37V45xx/ KDL-37V47xx/ KDL-32V45xx/ KDL-32V47xx:
TV stand SU-FL300M.
Transporting
• Before transporting the TV set, disconnect all cables.
• Two or three people are needed to transport a large TV set.
• When transporting the TV set by hand, hold it as shown on the right. Do not put stress on the LCD panel and the frame around the screen.
• When lifting or moving the TV set, hold it firmly from the bottom.
• When transporting the TV set, do not subject it to jolts or excessive vibration.
• When transporting the TV set for repairs or when moving, pack it using the original carton and packing material.
Ventilation
• Never cover the ventilation holes or insert anything in the cabinet.
• Leave space around the TV set as shown below.
• It is strongly recommended that you use a Sony wall­mount bracket in order to provide adequate air­circulation.
Be sure to hold the bottom of the panel, not the front part.
10 cm
10 cm
10 cm
Leave at least this space around the set.
Installed with stand
30 cm
10 cm10 cm
6 cm
Leave at least this space around the set.
• To ensure proper ventilation and prevent the collection of dirt or dust: – Do not lay the TV set flat, install upside down,
backwards, or sideways.
– Do not place the TV set on a shelf, rug, bed or in a
closet.
– Do not cover the TV set with a cloth, such as curtains,
or items such as newspapers, etc.
– Do not install the TV set as shown below.
Air circulation is blocked.
Wall
Air circulation is blocked.
Wall
Mains lead
Handle the mains lead and socket as follows in order to avoid any risk of fire, electrical shock or damage and/or injuries:
– Use only Sony mains leads, not those of other brands. – Insert the plug fully into the mains socket. – Operate the TV set on a 220-240 V AC supply only. – When wiring cables, be sure to unplug the mains lead
for your safety and take care not to catch your feet on the cables.
– Disconnect the mains lead from the mains socket
before working on or moving the TV set. – Keep the mains lead away from heat sources. – Unplug the mains plug and clean it regularly. If the
plug is covered with dust and it picks up moisture, its
insulation may deteriorate, which could result in a
fire.
Continued
GB
9
Notes
• Do not use the supplied mains lead on any other equipment.
• Do not pinch, bend, or twist the mains lead excessively. The core conductors may be exposed or broken.
• Do not modify the mains lead.
• Do not put anything heavy on the mains lead.
• Do not pull on the mains lead itself when disconnecting the mains lead.
• Do not connect too many appliances to the same mains socket.
• Do not use a poor fitting mains socket.
When:
– Mains lead is damaged. – Poor fitting of mains socket. – TV set is damaged by being dropped, hit or having
something thrown at it.
– Any liquid or solid object falls through openings in
the cabinet.
Precautions
Prohibited Usage
Do not install/use the TV set in locations, environments or situations such as those listed below, or the TV set may malfunction and cause a fire, electrical shock, damage and/or injuries.
Location:
Outdoors (in direct sunlight), at the seashore, on a ship or other vessel, inside a vehicle, in medical institutions, unstable locations, near water, rain, moisture or smoke.
Environment:
Places that are hot, humid, or excessively dusty; where insects may enter; where it might be exposed to mechanical vibration, near flammable objects (candles, etc). The TV set shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV.
Situation:
Do not use when your hands are wet, with the cabinet removed, or with attachments not recommended by the manufacturer. Disconnect the TV set from mains socket and aerial during lightning storms.
Broken pieces:
• Do not throw anything at the TV set. The screen glass may break by the impact and cause serious injury.
• If the surface of the TV set cracks, do not touch it until you have unplugged the mains lead. Otherwise electric shock may result.
When not in use
• If you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental and safety reasons.
• As the TV set is not disconnected from the mains when the TV set is just turned off, pull the plug from the mains to disconnect the TV set completely.
• However, some TV sets may have features that require the TV set to be left in standby to work correctly.
For children
• Do not allow children to climb on the TV set.
• Keep small accessories out of the reach of children, so that they are not mistakenly swallowed.
If the following problems occur...
Turn off the TV set and unplug the mains lead immediately if any of the following problems occur. Ask your dealer or Sony service centre to have it checked by qualified service personnel.
Viewing the TV
• View the TV in moderate light, as viewing the TV in poor light or during long period of time, strains your eyes.
• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.
LCD Screen
• Although the LCD screen is made with high-precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD screen and is not a malfunction.
• Do not push or scratch the front filter, or place objects on top of this TV set. The image may be uneven or the LCD screen may be damaged.
• If this TV set is used in a cold place, a smear may occur in the picture or the picture may become dark. This does not indicate a failure. These phenomena disappear as the temperature rises.
• Ghosting may occur when still pictures are displayed continuously. It may disappear after a few moments.
• The screen and cabinet get warm when this TV set is in use. This is not a malfunction.
• The LCD screen contains a small amount of liquid crystal. Some fluorescent tubes used in this TV set also contain mercury. Follow your local ordinances and regulations for disposal.
Handling and cleaning the screen surface/cabinet of the TV set
Be sure to unplug the mains lead connected to the TV set from mains socket before cleaning. To avoid material degradation or screen coating degradation, observe the following precautions.
• To remove dust from the screen surface/cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.
• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the screen surface and cabinet material.
• When adjusting the angle of the TV set, move it slowly so as to prevent the TV set from moving or slipping off from its table stand
Optional Equipment
Keep optional components or any equipment emitting electromagnetic radiation away from the TV set. Otherwise picture distortion and/or noisy sound may occur.
10
GB
Overview of the remote
1 "/1 – TV standby
Turns the TV on and off from standby mode.
2 AUDIO
In analogue mode: Press to change the dual sound mode (page 24). In digital mode: Press to select the audio language (page 30).
3 – Subtitles
GUIDE
Press to display the subtitles on current program if TV channels broadcast such information (in digital mode only) (page 30).
4 / – Input select / Text hold
• In TV mode: Selects the input source from equipment connected to the TV sockets (page 18).
• In Text mode (page 14): Holds the current page.
5 F/f/G/g/ 6 OPTIONS (page 14, 19)
Enables you to access various viewing options and change/make adjustments according to the source and screen format.
7 HOME (page 21)
Displays the TV Home menu.
8 Coloured buttons (page 14, 15, 16) 9 Number buttons
• In TV mode: Selects channels. For channel numbers 10 and above, enter the second and third digit quickly.
• In Text mode: Enters the three digit page number to select the page.
0 – Favourite (page 16) qa PROG +/–//
• In TV mode: Selects the next (+) or previous (-) channel.
• In Text mode (page 14): Selects the next ( ) or previous ( ) page.
qs – Previous channel
Returns to the previous channel watched (for more than five seconds).
qd % – Mute the sound qf 2 +/– – Volume qg / – Text (page 14) qh RETURN
Returns to the previous screen of any displayed menu.
qj – GUIDE (page 15) qk ANALOG – Analogue mode (page 13) ql DIGITAL – Digital mode (page 13) w; BRAVIA Sync (page 19) wa – Screen mode (page 14) ws / – Info / Text reveal
• In digital mode: Displays details of the programme currently being watched.
• In analogue mode: Each time you press screen changes as follows: Displays information such as current channel number and screen format
• In Text mode (page 14): Reveals hidden information (e.g. answers to a quiz).
z
The number 5, PROG +, AUDIO and buttons have tactile dots. Use the tactile dots as references when operating the TV.
/ , the information on the
t Time is displayed t Information is hidden.
11
GB
Loading...
+ 25 hidden pages