Sony KDL-26S2000, KDL-26S2020, KDL-32S2000, KDL-32S2010, KDL-32S2020 Operating Instructions

...

Installation dimensions table

KDL-26S2000 KDL-26S2010 KDL-26S2020

KDL-32S2000 KDL-32S2010 KDL-32S2020 KDL-32V2000

KDL-26S2000 KDL-26S2010 KDL-26S2020 KDL-32S2000 KDL-32S2010 KDL-32S2020 KDL-32V2000

Installing the Wall-Mount Bracket

Center line of the screen when installed on the wall

Hole to secure the bracket screw temporarily

TV Model

KDL-26S2000 KDL-26S2010 KDL-26S2020

KDL-32S2000 KDL-32S2010 KDL-32S2020

KDL-32V2000

Installation dimensions may differ according to how the TV is installed.

The wall must be strong enough to support at least four times the weight of the TV that you are installing.

TV Dimensions Unit: mm Length for each mounting angle Unit: mm

A B C D E Mounting angle (α°) F G H

658 470 94 22 265

792 546 99 19 304

0° 150 183 287

20° 257 140 316

0° 155 262 284

20° 288 213 316

0° 155 262 284

20° 291 213 310

Weight (× 4)

11 kg

(44 kg)

15 kg

(60 kg)

15 kg

(60 kg)

To Customers:

For product protection and safety reasons, Sony strongly recommends that wall-mounting of your TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.

Your KDL-26S2000/KDL-26S2010/KDL-26S2020/KDL-32S2000/KDL-32S2010/ KDL-32S2020/KDL-32V2000 can be wall-mounted using SU-WL31 Wall-Mount

Bracket (sold separately). Please provide your licensed contractor with this installation supplement as well as the Instructions (supplied with the SU-WL31 Wall-Mount Bracket). Read these documents carefully for safety and proper installation.

To Sony Dealers and Contractors:

Provide full attention to safety during the installation, periodic maintenance and examination of this product.

Printed in Slovak Republic

– 4 –

2-684-954-11(1)

Installing the TV on a wall

The TV can be installed on a wall by attaching a WallMount Bracket (sold separately). Verify your TV’s model number and be sure to use the bracket specified for your model only. Refer to the Steps on this manual along with the Instructions supplied with the SU-WL31 Wall-Mount Bracket, to properly carry out the installation.

Step 1: Checking the parts

required for the installation

Open the Wall-Mount Bracket package and check the contents for all required parts along with the Instructions.

Step 2: Changing the position

of the arm bases

Step 5: Preparing for the

installation of the TV

Before detaching the Table-Top Stand, disconnect all the cables from the TV.

1 Rotate the cable holder by 90 degrees, and

pull it out.

Cable holder

3 Align the holes on the Mounting Hook Units

with the corresponding holes on the rear of the TV. Then secure them to the TV using four screws (supplied with SU-WL31).

The supplied screws (+PSW5 × L16)

Sufficient expertise is required for installing this product, especially to determine the strength of the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product to the wall to Sony dealers or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for any damage or injury caused by mishandling or improper installation.

Refer to the Instructions for the SU-WL31.

Step 3: Deciding on the

installation location

Decide where you want to install your TV. Turn to the back cover of this manual for the TV installation dimensions and determine the location.

Refer to the Instructions for the SU-WL31.

Step 4: Installing the Plate

Unit on the wall

Refer to the Instructions for the SU-WL31.

Soft cloth

2 Remove the screws and detach the Table-

Top Stand from the TV.

Table-Top Stand

Notes

• Lay the display face down on a stable and level sur face

with the Table-Top Stand hanging over the edge of the surface. Having the display face and the base of the Stand on the same level surface will create an unstable working condition and can damage the TV.

• To prevent damaging the surface of the LCD display,

place the TV on a soft cloth.

Mounting Hook Units

Note

When using an electric screwdriver to tighten the screws, the torque must be approx. 2 N

•

m (20 kgf•cm).

Step 6: Installing the TV on

the Plate Unit

Refer to the Instructions for the SU-WL31.

1 Connect the mains lead and cables to the

corresponding sockets on the rear of the TV. For details on the cable connection, refer to the Operating Instructions for your TV.

2 Install the TV onto the Plate Unit.

– 2 – – 3 –