Sony KDF-50E2010 Operating Instructions

2-695-226-42(1)

LCD Projection TV

KDF-50E2000 KDF-50E2010

Operating Instructions

Before operating the TV, please read the “Safety information” section of this manual. Retain this manual for future reference.

For useful information about Sony products

NOTICE FOR CUSTOMERS IN THE

Introduction

Thank you for choosing this Sony product. Before operating the TV, please read this manual thoroughly and retain it for future reference.

UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362 (i.e., marked with or ) must be used. When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.

FUSE

How to replace the fuse

Open the fuse compartment with a blade screwdriver, and

replace the fuse.

Notice for Digital TV function

• Any functions related to Digital TV ( ) will only work in countries or areas where DVB-T (MPEG2) digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive a DVB-T signal where you live.

• Although this TV set follows DVB-T specifications, compatibility with future DVB-T digital terrestrial broadcasts cannot be guaranteed.

• Some Digital TV functions may not be available in some countries.

Trademark information

• is a registered trademark of the DVB Project

• Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under one or more of the following US patents: 5510752, 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.

• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

• This TV incorporates

High-Definition Multimedia Interface (HDMI™) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

Table of Contents

Start-up Guide 4

Safety information .....................................................................................................................7

Precautions .............................................................................................................................10

Overview of the remote ...........................................................................................................11

Overview of the TV buttons and indicators ........................................................................12

Watching TV

Watching TV............................................................................................................................13

Checking the Digital Electronic Programme Guide (EPG) ............................................15

Using the Favourite list ................................................................................................17

Viewing pictures from connected equipment ..........................................................................18

Using MENU Functions

Navigating through menus ......................................................................................................19

Picture Adjustment menu ........................................................................................................20

Sound Adjustment menu.........................................................................................................21

Features menu ........................................................................................................................23

Set-up menu............................................................................................................................25

Digital Set-up menu .....................................................................................................28

Using Optional Equipment

Connecting optional equipment...............................................................................................30

Additional Information

Optimum Viewing Area ...........................................................................................................32

Replacing the lamp .................................................................................................................33

Specifications ..........................................................................................................................36

Troubleshooting ......................................................................................................................38

Index .......................................................................................................................................40

: for digital channels only

Start-up Guide

1: Checking the accessories

Remote RM-ED007 (1)

Size AA batteries (R6 type) (2)

Aerial Adaptor

To insert batteries into the remote

Notes

• Observe the correct polarity when inserting batteries.

• Dispose of batteries in an environmentally friendly way. Certain regions may regulate disposal of the battery. Please consult your local authority.

• Do not use different types of batteries together or mix old and new batteries.

• Handle the remote with care. Do not drop or step on it, or spill liquid of any kind onto it.

• Do not place the remote in a location near a heat source, or in a place subject to direct sunlight, or in a damp room.

2: Connecting an aerial/ VCR

Connecting an aerial only

Aerial cable

(not supplied)

Aerial Adaptor

Connecting an aerial and VCR

Aerial Adaptor

(SMARTLINK)

Scart lead (not supplied)

RF lead

(not supplied)

VCR

3: Bundling the cables 4: Preventing the TV

from toppling over

Sony strongly recommends using the TV stand SURG11M with a support belt designed for your TV.

Selecting the language

and country/region

Start-up Guide

TIMER LA MP

POWER/STANDBY

POWER

PUSH OPEN

WEGA GATE

TV/VIDEO

CANNELVOLUME

3,4

1 Connect the TV to your mains socket

(220-240V AC, 50Hz).

2 Press 1 on the TV (front side).

When you switch on the TV for the first time, the Language menu appears on the screen. When the TV is in standby mode (the indicator on the TV (front) is red), press "/1 on the remote to switch on the TV.

1 (standby)

Continued

3 Press F/f to select the language

displayed on the menu screens, then press

Auto Start Up

Language

Country

6: Auto-tuning the TV

After selecting the language and country/region, a message confirming the TV start auto-tuning appears on the screen. The TV will now search for and store all available TV channels.

Select:

Confirm:

4 Press F/f to select the country/region in

which you will operate the TV, then press

Auto Start Up

Language

Country

Select:

If the country/region in which you want to use the TV does not appear in the list, select “-” instead of a country/region. The message confirming the TV start auto-tuning appears on the screen, then go to “6: Auto-tuning the TV”.

Confirm:

1 Press .

Back:

Start:

The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, please be patient and do not press any buttons on the TV or remote.

If a message appears for you to confirm the aerial connections

No digital or analogue channels were found. Check all the aerial connections and press to start auto-tuning again.

Cancel:

2 When the Programme Sorting menu

appears on the screen, follow the steps of “Programme Sorting” (page 25).

If you do not wish to change the order in which the analogue channels are stored on the TV, go to step

3 Press MENU to exit.

The TV has now tuned in all the available channels.

Safety information

Mains lead

• Observe the followings to prevent the mains lead being damaged. If the mains lead is damaged, it may result in a fire or an electric shock. – When you disconnect the mains

lead, disconnect it from the mains socket first.

– Be sure to grasp the plug when

disconnecting the mains lead. Do not pull on the mains lead itself.

– Do not pinch, bend, or twist the

mains lead excessively. The core conductors may be exposed or

broken. – Do not modify the mains lead. – Do not put anything heavy on the mains lead. – Keep the mains lead away from heat sources.

• If you damage the mains lead, stop using it and ask your dealer or Sony service centre to exchange it.

• Do not use the supplied mains lead on any other equipment.

• Use only an original Sony mains lead, not other brands.

Mains socket

Do not use a poor fitting mains socket. Insert the plug fully into the mains socket. A poor fit may cause arcing and result in a fire. Contact your electrician to have the mains socket changed.

Cleaning the mains plug

Unplug the mains plug and clean it regularly. If the plug is covered with dust and it picks up moisture, its insulation may deteriorate and result in a fire.

Overloading

This TV set is designed to operate on a 220–240 V AC supply only. Take care not to connect too many appliances to the same mains socket as this could result in fire or electric shock.

When not in use

• If you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental and safety reasons.

• The TV set is not disconnected from the mains when the TV set is switched off. To disconnect the TV set completely, pull the plug from the mains. However, some TV sets may have features which need the TV set to be left in standby to work correctly.

Carrying

• Before carrying the TV set, disconnect all the cables from the TV set.

• Carrying the large size TV set requires two or more people.

• When you carry the TV set by hand, hold the TV set as illustrated on the right. When lifting the TV set or moving the panel of the TV set, hold it firmly from the bottom. If you do not do so, the TV set may fall and be damaged or cause serious injury.

• When transporting it, do not subject the TV set to jolts or excessive vibration. The TV set may fall and be damaged or cause serious injury.

• If the TV set has been dropped or damaged, have it checked immediately by qualified service personnel.

• When you carry the TV set in for repair or when you move it, pack it using the original carton and packing material.

Placement

• The TV set should be installed near an easily accessible mains socket.

• Place the TV set on a stable, level surface. Do not hang anything on the TV set. If you do, the TV set may fall from the stand, causing damage or serious injury.

• Do not install the TV set in places subject to extreme temperature, for example in direct sunlight, or near a radiator, or heating vent. If the TV set is exposed to extreme temperature, the TV set may overheat and cause deformation of the casing or cause the TV set to malfunction.

• Do not install the TV set in a place exposed to direct air conditioning. If the TV set is installed in such a location, moisture may condense inside and may cause a malfunction.

• Never place the TV set in hot, oily, humid or excessively dusty places.

• Do not install the TV set where insects may enter.

• Do not install the TV set where it may be exposed to mechanical vibration.

• Do not install the TV set in a location where it may protrude, such as on or behind a pillar, or where you might bump your head on it. Otherwise, it may result in injury.

• Do not allow children to climb on the TV set.

• If you use the TV set near the seashore, salt may corrode metal parts of the TV set and cause internal damage or fire.

Continued

Ventilation

• Never cover the ventilation holes or insert anything in the cabinet. It may cause overheating and result in a fire.

• Unless proper ventilation is provided, the TV set may gather dust and get dirty. For proper ventilation, observe the following: – Do not install the TV set turned backwards or sideways. – Do not install the TV set turned over or upside down. – Do not install the TV set on a shelf or in a closet. – Do not place the TV set on a rug or bed. – Do not cover the TV set with cloth, such as curtains, or

items such as newspapers, etc.

• Leave some space around the TV set as shown below. Otherwise, air-circulation may be inadequate and causing overheating, which may cause a fire or damage to the TV set.

30 cm

10 cm

TIMER LAMP

POWER/STANDBY

POWER

PUSH OPEN

WEGA GATE

TV/VIDEO

CANNELVOLUM E

Leave at least this much space.

• Never install the TV set as follows:

Air circulation is blocked.

Wall

Optional accessories

Observe the following when installing the TV set using a stand or wall-mount bracket. If you do not do so, the TV set may fall and cause serious injury.

• It is strongly recommended that you use Sony accessories for safety reasons: – TV stand RG11M.

• Secure the TV set properly, following the instructions supplied with your stand when installing the TV set.

• Be sure to attach the brackets supplied with your stand.

Wiring

• When wiring cables, be sure to unplug the mains lead for your safety.

• Take care not to catch your feet on the cables. It may damage the TV set.

Medical institutions

Do not place this TV set in a place where medical equipment is in use. It may cause a malfunction of medical instruments.

15 cm

Outdoor use

• Do not install this TV set outdoors. If the TV set is exposed to rain, it may result in a fire or an electrical shock.

• If this TV set is exposed to direct sunlight, the TV set may heat up and it may damage the TV set.

Vehicle, Ships and other vessels

• Do not install this TV set in a vehicle. The motion of the vehicle may cause the TV set to fall down and cause injury.

• Do not install this TV set on a ship or other vessel. If the TV set is exposed to seawater, it may cause a fire or damage the TV set.

Water and moisture

• Do not use this TV set near water – for example, near a bathtub or shower room. Also do not expose to rain, moisture or smoke. This may result in a fire or an electric shock.

• Do not touch the mains lead and the TV set with wet hands. Doing so may cause an electric shock or damage to the TV set.

Moisture and flammable objects

• Do not place any objects on the TV set. The TV set shall not be exposed to dripping or splashing and that no objects filled with liquid, such as vases, shall be placed on the TV set.

• To prevent fire, keep flammable objects or naked lights (e.g. candles) away from the TV set.

• If any liquid or solid object does fall through openings in the cabinet, do not operate the TV set. It may result in an electric shock or damage to the TV set. Have it checked immediately by qualified service personnel.

Lightning storms

For your own safety, do not touch any part of the TV set, mains lead, or aerial lead during lightning storms.

Broken pieces

• Do not throw anything at the TV set. The screen glass may break by the impact and cause serious injury.

• If the surface of the TV set cracks, do not touch it until you have unplugged the mains lead. Otherwise electric shock may result.

Servicing

Dangerously high Voltage are present inside the TV set. Do not open the cabinet. Entrust the TV set to qualified service personnel only.

Small accessories removal and fittable

Keep small accessories out of children’s reach.

Precautions

Viewing the TV

• To view the TV comfortably, the recommended viewing position is from four to seven times the screen’s vertical length away from the TV set.

• To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible, use spot lighting directed down from the ceiling.

• View the TV in moderate light, as viewing the TV in poor light or during long period of time, strains your eyes.

Volume adjustment

• Adjust the volume so as not to trouble your neighbours. Sound carries very easily at night time. Therefore, closing the windows or using headphones is suggested.

• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.

Handling and cleaning the screen surface/cabinet of the TV set

Be sure to unplug the mains lead connected to the TV set from mains socket before cleaning. To avoid material degradation or screen coating degradation, observe the following precautions.

• Do not push on the screen, scratch it with a hard object, or throw anything at it. The screen may be damaged.

• Do not touch the display panel after operating the TV set continuously for a long period as the display panel becomes hot.

• We recommend that the screen surface be touched as little as possible.

• To remove dust from the screen surface/cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.

• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the screen surface and cabinet material.

• The ventilation holes can accumulate dust over time. To ensure proper ventilation, we recommend removing the dust periodically (once a month) using a vacuum cleaner.

• If the angle of the TV set is to be adjusted, steady the base of the stand with your hand to prevent the TV set from becoming separated from the stand. Be careful not to get your fingers caught between the TV set and the stand.

Optional Equipments

• Do not install optional components too close to the TV set. Keep optional components at least 30 cm away from the TV set. If a VCR is installed in front of the TV set or beside the TV set, the picture may become distorted.

• Picture distortion and/or noisy sound may occur if the TV set is positioned in close proximity to any equipment emitting electromagnetic radiation.

Disposal of the TV set

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Overview of the remote

1 "/1 – TV standby

Switches the TV on and off from standby mode.

2 – Screen mode (page 14) 3 Coloured buttons

• In digital mode (page 15, 17): Selects the options at the bottom of the Favourite and EPG digital menus.

• In Text mode (page 14): Used for Fastext.

4 / – Info / Text reveal

• In digital mode: Displays brief details of the programme currently being watched.

• In analogue mode: Displays information such as current channel number and screen mode.

• In Text mode (page 14): Reveals hidden information (e.g., answers to a quiz).

5 F/f/G/g/ (page19) 6 Picture Freeze (page 14)/

• In TV mode: Freezes the TV picture.

• In PC mode: Displays a small picture (PIP).

7 MENU (page 19) 8 DIGITAL – Digital mode (page 13) 9 Number buttons

• In TV mode: Selects channels. For channel numbers 10 and above, enter the second digit within two seconds.

• In Text mode: Enters the three digit page number to select the page.

0 – Previous channel

Returns to the previous channel watched (for more than five seconds).

qa PROG +/- (page 13)

• In TV mode: Selects the next (+) or previous (-) channel.

• In Text mode: Selects the next (+) or previous (-) page.

qs 2 +/- – Volume qd % – Mute (page 13)

/ – Text (page 14)

qf qg ANALOG – Analogue mode (page 13) qh / RETURN

Returns to the previous screen of any displayed menu.

qj – EPG (Digital Electronic Programme Guide) (page 15) qk – Picture mode (page 20) ql 9 – Sound effect (page 21) w; – Input select / Text hold

• In TV mode (page 18): Selects the input source from equipment connected to the TV sockets.

• In Text mode (page 14): Holds the current page.

PIP in PC Mode (page 14)

Tip

The PROG + and number 5 buttons have tactile dots. Use the tactile dots as references when operating the TV.

Overview of the TV buttons and indicators

21593 4678

TIMER LAMP

POWER/STANDBY

PUSH OPEN

WEGA GATE

TV/VIDEO

1 (page 19) 2 / –Input select (page 18)

• In TV mode: Selects the input source from equipment connected to the TV sockets.

• In TV menu: OK

3 2 +/-/ </,

• Increases (+) or decreases (-) the volume.

• In TV menu: Moves through the options left (

<) or right (,).

4 PROG +/-/ M/m

• In TV mode: Selects the next (+) or previous (-) channel.

• In TV menu: Moves through the options up (

M) or down (m).

5 –Sleep Timer (page 24)

• Lights up in amber when the “Sleep Timer” is set or when a digital event is programmed.

• Lights up in amber when digital REC starts.

6 Lamp Indicator.

Lights up in red when the lamp for the light source has burned out (page 33)

7 1 – Power indicator / Standby indicator

• Lights up in green when the TV is switched on.

• Lights up in red when the TV is in standby mode.

8 Remote control sensor 9 1 – Power

Switches the TV on or off.

POWER

CANNELVO LUM E

Watching TV

TIMER LA MP

POWER/STANDBY

POWER

PUSH OPEN

WEGA GATE

TV/VIDEO

CANNELVOLUM E

3 Press the number buttons or PROG +/- to

select a TV channel.

To select channel numbers 10 and above using the number buttons, enter the second and third digits within two seconds. To select a digital channel using the Digital Electronic Programme Guide (EPG), see page 15.

In digital mode

An information banner appears briefly. The following icons may be indicated on the banner.

: Interactive service is available (MHEG Digital

Text)

: Interactive service (MHEG Digital Text) is

currently disabled

: Radio service

: Scrambled/Subscription service

: Multiple audio languages available

: Subtitles available

: Subtitles available for the hearing impaired

: Recommended minimum age for current

programme (from 4 to 18 years)

: Parental Lock

: Current programme is being recorded

Additional operations

Watching TV

1 Press 1 on the TV (front side) to switch on

the TV.

When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press "/1 on the remote to switch on the TV.

2 Press DIGITAL to switch to digital mode or

ANALOG to switch to analogue mode.

The channels available vary depending on the mode.

To Do this

Turn off the TV temporarily (Standby mode)

Turn on the TV from Standby mode without sound

Switch off the TV. Press 1 on the TV.

Note

To disconnect the TV completely, pull the plug from the mains.

Adjust the volume Press 2 + (increase)/

Mute the sound Press %. Press again to restore.

Access the Programme index table (in analogue mode only)

Press "/1.

Press %. Press 2 +/- to set the volume level.

- (decrease).

Press . To select an analogue channel, press

. To access the Input signal index table, see page 18.

F/f, then press

Continued

+ 28 hidden pages