Sony ILX533K Datasheet
2700 pixel × 3 line CCD Linear Sensor (Color)
For the availability of this product, please contact the sales office.
Description
The ILX533K is a reduction type CCD linear sensor
developed for color image scanner. The distance
between lines is only 4 line (32µm). This sensor reads
A4-size documents at a density of 300DPI.
Features
• Number of effective pixels: 8100 pixels
(2700 pixels × 3)
• Pixel size: 8µm × 8µm (8µm pitch)
• Distance between line: 32µm (4 Lines)
• Number of output 3 (R, G, B)
• Single-sided readout
• Clamp circuit are on-chip
• Ultra high sensitivity/Ultra low lag
• Single 12V power supply
• Maximum data rate: 9MHz (3MHz × 3)
• Input Clock Pulse: CMOS 5V drive
• Package: 22 pin cer-DIP (400 mil)
Block Diagram
φROG-B
11
ILX533K
22 pin DIP (Cer-DIP)
φROG-G
12
φROG-R
13
Absolute Maximum Ratings
• Supply voltage VDD 15 V
• Operating temperature –10 to +55 °C
• Storage temperature –30 to +80 °C
Pin Configuration (Top View)
19
18
17
16
15
14
22
21
20
GND
GND
OUT-B
V
NC
NC
NC
NC
NC
φ2
φRS
OUT-R
V
VOUT-G
VDD
NC
NC
NC
NC
NC
1
2
3
4
5
6
7
8
9
Driver
φ2
14
S2700
Blue
Read Out Gate
S1
D63
D15
D14
CCD Register
VDD
4
Clamp
20
Green
S1
D63
D15
D14
Driver
S2700
Red
Read Out Gate
CCD Register
Clamp
3
S1
D63
D15
D14
Driver
S2700
Read Out Gate
CCD Register
Clamp Pulse
Clamp
2
Driver
Generator
10
1
21
φRS φ1
GND
φROG
φ1
10
11
-B
2700 G 1
2700 R 1
13
2700 B 1
12
φROG
φROG-G
-R
VOUT-B
VOUT-G
VOUT-R
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
– 1 –
E97406B79-PS
Pin Description
Pin No. Symbol Description Pin No. Symbol Description
ILX533K
1
2
3
4
5
6
7
8
9
10
11
φRS
VOUT-R
VOUT-G
VDD
NC
NC
NC
NC
NC
φ1
φROG-B
Clock pulse input
Signal out (red)
Signal out (green)
12V power supply
NC
NC
NC
NC
NC
Clock pulse input
Clock pulse input
Recommended Supply Voltage
Item
VDD
Min.
11.4
Typ.
12
Max.
12.6
Unit
V
12
13
14
15
16
17
18
19
20
21
22
φROG-G
φROG-R
φ2
NC
NC
NC
NC
NC
VOUT-B
GND
GND
Clock pulse input
Clock pulse input
Clock pulse input
NC
NC
NC
NC
NC
Signal out (blue)
GND
GND
Clock Characteristics
Item
Input capacity of φ1, φ2
Input capacity of φRS
Input capacity of φROG
∗1
It indicates that φROG-R, φROG-G, φROG-B as φROG.
∗1
Symbol
Cφ1, Cφ2
CφRS
CφROG
Clock Frequency
Item Symbol
φ1, φ2, φRS fφ1, fφ2, fφRS
Input Clock Pulse Voltage Condition
Item
φ1, φ2, φRS, φROG
pulse voltage
High level
Low level
Min.
—
—
—
Min.
4.75
—
Min.
—
Typ.
400
10
10
Typ.
5.0
0
Typ.
1
Max.
—
—
—
Max.
5.25
0.1
Max.
3
Unit
pF
pF
pF
Unit
MHz
Unit
V
V
– 2 –
Electrooptical Characteristics (Note 1)
Ta = 25°C, VDD = 12V, fφRS = 1MHz, Input clock = 5Vp-p,
Light source = 3200K, IR cut filter CM-500S (t = 1.0mm)
Item Symbol Min. Typ. Max. Unit Remarks
ILX533K
Red
Sensitivity
Green
Blue
Sensitivity nonuniformity
Saturation output voltage
Red
Saturation
exposure
Green
Blue
Dark voltage average
Dark signal nonuniformity
Image lag
Supply current
Total transfer efficiency
Output impedance
Offset level
RR
RG
RB
PRNU
VSAT
SER
SEG
SEB
VDRK
DSNU
IL
IVDD
TTE
ZO
VOS
6.2
12.3
7.5
—
2.0
0.15
0.10
0.12
—
—
—
—
92
—
—
9.5
19
11.5
4
2.5
0.26
0.13
0.21
2
4
0.02
30
98
300
6.3
12.8
25.6
15.5
20
—
—
—
—
5
12
—
50
—
—
—
V/(lx · s)
%
V
lx · s
mV
mV
%
mA
%
Ω
V
Note 2
Note 3
Note 4
Note 5
Note 6
Note 6
Note 7
—
—
—
Note 8
Note
1) In accordance with the given electrooptical characteristics, the black level is defined as the average value
of D2, D3 to D12.
2) For the sensitivity test light is applied with a uniform intensity of illumination.
3) PRNU is defined as indicated below. Ray incidence conditions are the same as for Note 2.
VOUT-G = 500mV (Typ.)
PRNU = × 100 [%]
(VMAX – VMIN) /2
VAVE
Where the 2700 pixels are divided into blocks of 100. The maximum output of each block is set to VMAX,
the minimum output to VMIN and the average output to VAVE.
4) Use below the minimum value of the saturation output voltage.
5) Saturation exposure is defined as follows.
SE =
VSAT
R
Where R indicates RR, RG, RB, and SE indicates SER, SEG, SEB.
6) Optical signal accumulated time τint stands at 5ms.
7) VOUT-G = 500mV (Typ.)
VOUT
8) Vos is defined as the right side.
VOUT indicates VOUT-R, VOUT-G, and VOUT-B.
– 3 –
VOS
GND
ILX533K
2770
D70
D65
D64
S2700
S2699
S2698
S2
S1
D63
D62
D61
D15
D14
Optical black (49 pixels)
D13
1-line output period
Clock Timing Chart 1
5
0
φROG
4
3
2
1
5
0
5
0
5
0
φ1
φ2
φRS
D3
D2
D1
OUT
V
Dummy signal (63 pixels)
Noto) The transfer pulses (φ1, φ2) must have more than 2770 cycles.
VOUT indicates VOUT-R, VOUT-G, VOUT-B.
– 4 –
Loading...