Sony ICX058CK Datasheet

Description
The ICX058CK is an interline CCD solid-state image sensor suitable for NTSC color video cameras. Compared with the current product ICX058AK, sensitivity is improved drastically through the adoption of Super HAD CCD technology. High resolution is achieved through the use of Ye, Cy, Mg, and G complementary color mosaic filters.
Features
High sensitivity (+3dB at F5.6, +4dB at F1.2 compared with ICX058AK)
High resolution, low smear and low dark current
Excellent antiblooming characteristics
Continuous variable-speed shutter
Ye, Cy, Mg, and G complementary color mosaic filters on chip
Horizontal register: 5V drive
Reset gate: 5V drive
Device Structure
Interline CCD image sensor
Image size: Diagonal 6mm (Type 1/3)
Number of effective pixels: 768 (H) × 494 (V) approx. 380K pixels
Number of total pixels: 811 (H) × 508 (V) approx. 410K pixels
Chip size: 6.00mm (H) × 4.96mm (V)
Unit cell size: 6.35µm (H) × 7.40µm (V)
Optical black: Horizontal (H) direction: Front 3 pixels, rear 40 pixels
Vertical (V) direction: Front 12 pixels, rear 2 pixels
Number of dummy bits: Horizontal 22
Vertical 1 (even field only)
Substrate material: Silicon
– 1 –
ICX058CK
E95212A99
Diagonal 6mm (Type 1/3) CCD Image Sensor for NTSC Color Video Camera
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
A
A
A
Pin 1
V
3
40
2
12
Pin 9
H
Optical black position
(Top View)
16 pin DIP (Plastic)
Super HAD CCD is a registered trademark of Sony Corporation. Super HAD CCD is a CCD that drastically improves sensitivity by introducing newly developed semiconductor technology by Sony Corporation into Sony's high-performance HAD (Hole-Accumulation Diode) sensor.
AAA AAA AAA
– 2 –
ICX058CK
Substrate voltage SUB – GND
Supply voltage
Vertical clock input voltage
Voltage difference between vertical clock input pins Voltage difference between horizontal clock input pins Hφ1, Hφ2 – Vφ4 Hφ1, Hφ2, LHφ1, RG, VGG – GND Hφ1, Hφ2, LHφ1, RG, VGG – SUB VL – SUB Vφ1, Vφ2, Vφ3, Vφ4, VDD, VOUT – VL RG – VL VGG, VSS, Hφ1, Hφ2, LHφ1 – VL Storage temperature Operating temperature
Block Diagram and Pin Configuration
(Top View)
1
2
3
4
5
6
7
8
9
10
11
12
13
14 15
16
Note)
Note) : Photo sensor
V
OUT
V
SS
V
GG
GND
Vφ
1
Vφ
2
Vφ
3
Vφ
4
V
DD
GND
SUB
V
L
RG
LHφ
1
Hφ
1
Hφ
2
Horizontal register
Cy
Ye
Cy
Ye
Mg
G
Mg G
Cy
Ye
Cy Ye
G Mg G Mg
Cy
Ye Cy Ye
Mg G Mg G
Vertical register
Pin No.
1 2 3 4 5 6 7 8
Vφ4 Vφ3 Vφ2 Vφ1 GND VGG VSS VOUT
Vertical register transfer clock Vertical register transfer clock Vertical register transfer clock Vertical register transfer clock GND Output amplifier gate bias Output amplifier source Signal output
9 10 11 12 13 14 15 16
VDD GND SUB VL RG LHφ1 Hφ1 Hφ2
Output amplifier drain supply GND Substrate (Overflow drain) Protective transistor bias Reset gate clock Horizontal register final stage transfer clock Horizontal register transfer clock Horizontal register transfer clock
Symbol
Description
Pin No.
Description
Pin Description
Absolute Maximum Ratings
–0.3 to +55 –0.3 to +18
–55 to +10 –15 to +20
to +10 to +15
to +17 –17 to +17 –10 to +15 –55 to +10
–65 to +0.3 –0.3 to +30 –0.3 to +24 –0.3 to +20
–30 to +80 –10 to +60
V V V V V V V V V V V V V
V °C °C
1
VDD, VOUT, VSS – GND VDD, VOUT, VSS – SUB Vφ1, Vφ2, Vφ3, Vφ4 – GND Vφ1, Vφ2, Vφ3, Vφ4 – SUB
Item Ratings Unit Remarks
1
+27V (Max.) when clock width < 10µs, clock duty factor < 0.1%.
Symbol
– 3 –
ICX058CK
Bias Conditions
Item Output amplifier drain voltage Output amplifier gate voltage
Output amplifier source Substrate voltage adjustment range
Fluctuation range after substrate voltage adjustment Reset gate clock voltage adjustment range Fluctuation range after reset gate clock voltage
adjustment Protective transistor bias
VDD VGG
VSS VSUB
VSUB VRGL
VRGL VL
14.55
3.8
9.0 –3
1.0 –3
15.0
4.2
15.45
4.65
18.5 +3
4.0 +3
V V
V
%
V
%
±5%
1
1, ∗6
Symbol Min. Typ. Max. Unit Remarks
DC Characteristics
Item Output amplifier drain current Input current Input current
IDD IIN1 IIN2
5
1
10
mA
µA µA
34
Symbol Min. Typ. Max. Unit Remarks
Grounded with
820resistor
2
1
Indications of substrate voltage (VSUB) · reset gate clock voltage (VRGL) setting value. The setting values of substrate voltage and reset gate clock voltage are indicated on the back of the image sensor by a special code. Adjust substrate voltage (VSUB) and reset gate clock voltage (VRGL) to the indicated voltage. Fluctuation range after adjustment is ±3%.
VSUB code one character indication VRGL code one character indication ↑ ↑
VRGL code VSUB code
Code and optimal setting correspond to each other as follows.
1
VRGL code Optimal setting 1.0 1.5 2.0 2.5 3.0 3.5 4.0
2
3
4 5
6
7
VSUB code Optimal setting
9.0 9.5
10.0 10.5 11.0 11.5 12.012.5 13.0 13.5 14.0 14.5 15.0 15.516.0 16.5 17.0 17.5 18.0 18.5
E f G
h J K L
m
N P
Q
R
S
T
U V W X
Y
Z
<Example> “5L” VRGL = 3.0V
VSUB = 12.0V
2
VL setting is the VVL voltage of the vertical transfer clock waveform.
3
1) Current to each pin when 18V is applied to VDD, VOUT, Vss and SUB pins, while pins that are not tested are grounded.
2) Current to each pin when 20V is applied sequentially to Vφ1, Vφ2, Vφ3 and Vφ4 pins, while pins that are not tested are grounded. However, 20V is applied to SUB pin.
3) Current to each pin when 15V is applied sequentially to RG, LHφ1, Hφ1, Hφ2 and VGG pins, while pins that are not tested are grounded. However, 15V is applied to SUB pin.
4) Current to VL pin when 30V is applied to Vφ1, Vφ2, Vφ3, Vφ4, VDD and VOUT pins or when, 24V is applied to RG pin or when, 20V is applied to VGG, Vss, Hφ1, Hφ2 and LHφ1 pins, while VL pin is grounded. However, GND and SUB pins are left open.
4
Current to SUB pin when 55V is applied to SUB pin, while pins that are not tested are grounded.
– 4 –
ICX058CK
Clock Voltage Conditions
Item
Readout clock voltage
VVT VVH1, VVH2 VVH3, VVH4 VVL1, VVL2,
VVL3, VVL4 VφV | VVH1 – VVH2 | VVH3 – VVH VVH4 – VVH VVHH VVHL VVLH VVLL VφH,VφLH VHL,VLHL VφRG VRGLH – VRGLL VφSUB
14.55 –0.05
–0.2 –9.0
7.8
–0.25 –0.25
4.75
–0.05
4.5
22.5
15.0 0 0
–8.5
8.5
5.0 0
5.0
23.5
15.45
0.05
0.05 –8.0
9.05
0.1
0.1
0.1
0.5
0.5
0.5
0.5
5.25
0.05
5.5
0.8
24.5
V V V
V V
V V V V V V V V V V V V
1 2 2
2 2
2 2 2 2 2 2 2 3 3 4 4 5
VVH = (VVH1 + VVH2)/2
VVL = (VVL3 + VVL4)/2 VφV = VVHn – VVLn (n = 1 to 4)
High-level coupling High-level coupling Low-level coupling Low-level coupling
556
Low-level coupling
Horizontal transfer clock voltage
Reset gate clock voltage
Substrate clock voltage
Vertical transfer clock voltage
Symbol Min.
Typ. Max.
Unit
Waveform
diagram
Remarks
5
The horizontal final stage transfer clock input pin LHφ1 is connected to the horizontal transfer clock input pin Hφ1.
6
The reset gate clock voltage need not be adjusted when reset gate clock is driven when the specifications are as given below. In this case, the reset gate clock voltage setting indicated on the back of the image sensor has not significance.
Item
Symbol
VRGL VφRG
Min.
Typ.
Max.
Unit
Waveform
diagram
–0.2
8.5
0
9.0
0.2
9.5
V V
4 4
Remarks
Reset gate clock voltage
– 5 –
ICX058CK
Clock Equivalent Circuit Constant
Item
Capacitance between vertical transfer clock and GND
CφV1, CφV3 CφV2, CφV4 CφV12, CφV34 CφV23, CφV41 CφV13 CφV24
CφH1, CφH2
CφHH
CφLH
CφRG
CφSUB R1, R2, R3, R4
RGND RφH
1000
560 470 330 220 100
47
43
8
8
270
80 15 15
pF pF pF pF pF pF
pF
pF
pF
pF
pF
Ω Ω Ω
Capacitance between vertical transfer clocks
Capacitance between horizontal transfer clock and GND
Capacitance between horizontal transfer clocks
Capacitance between horizontal final stage transfer clock and GND
Capacitance between reset gate clock and GND
Capacitance between substrate clock and GND
Vertical transfer clock series resistor Vertical transfer clock ground resistor Horizontal transfer clock series resistor
Symbol Min. Typ. Max. Unit Remarks
RφH RφH
Hφ2
Hφ1
CφH1
CφH2
CφHH
Vφ1
CφV12
Vφ2
Vφ4 Vφ3
CφV34
CφV23
CφV41
CφV13
CφV24
CφV1 CφV2
CφV4 CφV3
RGND
R4
R1
R3
R2
Vertical transfer clock equivalent circuit Horizontal transfer clock equivalent circuit
– 6 –
ICX058CK
VVH = (VVH1 + VVH2)/2 VVL = (VVL3 + VVL4)/2 VφV = VVHn – VVLn (n = 1 to 4)
Vφ1 Vφ3
Vφ2 Vφ4
VVHH
VVH
VVHL
VVHH
VVHL
VVH1
VVL1
VVLH
VVLL
VVL
VVHH
VVH3
VVHL
VVH
VVHH
VVHL
VVL3
VVL
VVLL
VVLH
VVHH VVHH
VVH
VVHL
VVHL
VVH2
VVLH
VVL2
VVLL
VVL
VVHH VVHH
VVHL
VVH4
VVHL
VVH
VVL
VVLH
VVLL
VVL4
Drive Clock Waveform Conditions
(1) Readout clock waveform
(2) Vertical transfer clock waveform
II II
100%
90%
10%
0%
VVT
tr twh tf
φM
0V
φM
2
Loading...
+ 13 hidden pages