Sony ICF-C111 Service manual

ICF-C111

SERVICE MANUAL

Ver 1.0 2001.03

SPECIFICATIONS

Time display

24-hour system

Frequency range

FM: 87.5 - 108 MHz
AM: 530 - 1710 kHz

Speaker

Approx. 6.6 cm (2 5/8 inches) dia., 8 ohm

Power output

100 mW (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz (E model)
220 - 230 V AC, 50 Hz (Singapore model)
For the power back-up function: 9 V DC, one 6F22 battery

Battery life

Approx. 60 hours, using Sony S-006P (6F22) battery

Dimensions

Approx. 146.5 × 100.5 × 123 mm (w/h/d)

7/8 × 4 × 4 7/8 inches) incl. projecting parts and controls

(5

Mass

Approx. 580 g (1 lb 4.4 oz) not incl. battery

Design and specifications are subject to change without notice.

E Model

9-873-094-11

2001C0400-1

© 2001.3

FM/AM CLOCK RADIO

Sony Corporation

Audio Entertainment Group

General Engineering Dept.

1

ICF-C111

Notes on Chip Component Replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

TABLE OF CONTENTS

1. SERVICING NOTES

1-1. Cord Dressing (Power Cord) ............................................... 3

1-2. Pointer Alignment ............................................................... 3

2. GENERAL

Setting the Clock ..................................................................... 4

Operating the Radio ................................................................. 4

Setting the Alarm ..................................................................... 4

Setting the Sleep Timer ........................................................... 4

3. DISASSEMBLY

3-1. Panel (Front)........................................................................ 5

3-2. Cabinet (Upper) Assy .......................................................... 6

3-3. Chassis Section ................................................................... 6

3-4. Main Board ......................................................................... 7

4. ELECTRICAL ADJUSTMENTS................................... 8

5. DIAGRAMS

5-1. Block Diagram .................................................................. 11

5-2. Printed Wiring Board ........................................................ 12

5-3. Schematic Diagram ........................................................... 13

6. EXPLODED VIEWS

6-1. Cabinet (Upper) Section .................................................... 14

6-2. Cabinet (Lower) Section ................................................... 15

7. ELECTRICAL PARTS LIST......................................... 16

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.

2

1-1. CORD DRESSING

s

(POWER CORD)

1) Connect the power cord as shown in the figure.

2) Mount the chassis with screws (P 3 × 10).
Note: Tighten completely the screws (P 3 × 10).

ICF-C111

SECTION 1

SERVICING NOTES

cabinet (lower)

screw (P 3x10)

pwb, power cord retainer

power cord

1-2. POINTER ALIGNMENT

2

Fit the pointer in the groove.

5

MAIN board

1

knob (tuning)

A

Turn this in the arrow direction
until stopped.

3

Fit the protrusion on the
pointer in the hole A.

4

Align the notch on the bos
of the knob (turning) with
the direction of CV1.

chassis section

3

ICF-C111

SECTION 2

GENERAL

This section is extracted
from instruction manual.

4

SECTION 3

DISASSEMBLY

• The equipment can be removed using the following procedure.

Set Panel (Front) Cabinet (Upper) Assy Chassis Section Main Board

Note : Follow the disassembly procedure in the numerical order given.

3-1. PANEL (FRONT)

claws

claw

ICF-C111

2

panel (front)

claw

claw

1

screws (P 3x10)

5

ICF-C111

y

3-2. CABINET (UPPER) ASSY

3

cabinet (upper) ass

3-3. CHASSIS SECTION

from MAIN board

1

2

screws (P 3x30)

CN701

from speaker

2

screw (P 3x10)

3

chassis section

1

screws (P 3x30)

6

3-4. MAIN BOARD

claw

1

screw (P 3x10)

claw

2

MAIN board

ICF-C111

7

ICF-C111

)

SECTION 4

ELECTRICAL ADJUSTMENTS

FM SECTION 0 dB = 1 µV

Setting:

BAND switch: FM
VOLUME switch: MIN

FM RF signal
generator

0.01

400Hz, 30% FM modulation
frequency deviation
Output level: as low as possible

±

22.5kHz

AM SECTION

Setting:

BAND switch: AM
VOLUME switch: MIN

AM RF signal
generator

400Hz, 30%
AM modulation
Output level: as low as possible

FM lead wire
antenna terminal

µ

F

set

Put the lead-wire
antenna close to
the set.

FM FREQUENCY COVERAGE ADJUSTMENT

Adjust for a maximum reading on level meter.

L4 CT4

86.5 MHz 109.5 MHz

FM TRACKING ADJUSTMENT

Adjust for a maximum reading on level meter.

L3 CT3

86.5 MHz 109.5 MHz

AM IF ADJUSTMENT

Adjust for a maximum reading on level meter.

T1

455 kHz

AM FREQUENCY COVERAGE ADJUSTMENT

Adjust for a maximum reading on level meter.

L2 CT2

520 kHz 1,750 kHz

AM TRACKING ADJUSTMENT

Adjust for a maximum reading on level meter.

L1 CT1

600 kHz 1,400 kHz

Adjustment Location: See page 9.

• Connecting Level Meter (FM and AM)

level meter
(range: 0.5–5 V ac

Ω

16

set

speaker terminal

Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally done
by the trimmer capacitors.

8

Adjustment Location:

FM

LEAD WIRE

ANTENNA

– MAIN board (component side) –

CT3, L3

FM

TRACKING

ADJUSTMENT

ICF-C111

CT1, L1

AM

TRACKING

ADJUSTMENT

SP1

CN701

1

6

SP1

(SPEAKER)

T1

T1

AM

IF

ADJUSTMENT

CT4, L4

FM

FREQUENCY

COVERAGE

ADJUSTMENT

L1

L3

L4

CT2, L2

AM

FREQUENCY

COVERAGE

ADJUSTMENT

CV1

TUNING

CT1

CT3

CT2

CT4

L2

S1

BAND

FM

AM

VR1

9

ICF-C111

THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.

Common Note on Schematic Diagram:

• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.

• All resistors are in Ω and 1/
specified.

f

•

• C : panel designation.

Note: The components identified by mark 0 or dotted line

• A : B+ Line.

• H : adjustment for repair.

• Total current is measured.

• Power voltage is dc 9V and fed with regulated dc power

• Voltage is dc with respect to ground under no-signal

• Voltages are taken with a VOM (Input impedance 10 MΩ).

• Waveforms are taken with a oscilloscope.

• Signal path.

• Abbreviation

: internal component.

with mark 0 are critical for safety.
Replace only with part number specified.

supply from battery terminal.

(detuned) condition.
no mark : FM
( ) : AM

Voltage variations may be noted due to normal produc­tion tolerances.

Voltage variations may be noted due to normal produc­tion tolerances.

F : FM
f : AM

SP : Singapore model.

4

W or less unless otherwise

SECTION 5

DIAGRAMS

Common Note on Printed Wiring Boards:

• X : parts extracted from the component side.

• Y : parts extracted from the conductor side.

f

•

• : Pattern from the side which enables seeing.

• Abbreviation

: internal component.

SP : Singapore model.

10

5-1. BLOCK DIAGRAM

ICF-C111

FM

LEAD WIRE

ANTENNA

MAIN BOARD

CT3,L3

FM

TRACKING

CT4,L4

FM

FREQUENCY

COVERAGE

CT1,L1

AM

TRACKING

FERRITE-ROD

CT2,L2

AM

FREQUENCY

COVERAGE

ANTENNA

CV1-3 CT3

L3

CV1-4 CT4

L4

L1

L2

CV1

TUNING

LED101

CLOCK DISPLAY

CV1-1 CT1

CV1-2 CT2

AM

• Signal path

: FM

: AM

• Abbreviation
SP : Singapore model

S1

BAND

FM

AM

16

BAND SW

FM ANT

13

FM FRONT-ENDAM FRONT-END

MIX OUT

REG

9

OSC 1/25 or 1/30

DISPLAY

DECODER/

DRIVER

FM RF

10 15

FM OSC

8

AM ANT

11

AM OSC

6

W703

1-13

1

|

13

14-16

+B

VREG

SLEEP

CF1

10.7MHz

3

DISCRI

FM

DISCRIMINATOR

ALARM

DISP

19

S5

ALARM

FM
IF IN

18

AM
IF IN

17

FM/AM
FRONT-END
IF AMP,DET

IC101

ALARM CLOCK

S3

TIME SET

M

D101

IC1

CF3

T1

CF2

T1

AM IF

DISPLAY

CONTROL

SLEEP

INPUT

23 21 22 24

S7

FM IF

AM IF

ALARM TIME CTR

INPUT

CONTROL

MIN SET

DET OUT

HOUR SET

S6

CLOCK

24 25

+B

27

S4

TIME SET

H

VR1

w VOLUME

AF IN

OUTPUT

CONTROL

SNOOZE INPUT

SNOOZE/SLEEP OFF

+B

AF POWER

AMP

Q201

RIPPLE

FILTER

SLEEP

ALARM

ALARM OFF

S7

5

VOL

OUT

OUT

Q1

AF OUT

17

16

18

(Function Selector)

VREG

28

NF

4

S2-1 S2-2

S2

BUZZER

RADIO

RADIO ON

ALARM

OFF

+B

E MODEL

+B

SWITCH

Q202

LED102

D203

SP MODEL

D201

D202 D204

+B

+B

+B

ALARM

D205

CN701

CN701

(2/2)

(1/2)

2

1

4

3

5

6

SP1

(SPEAKER)

DRY BATTERY

"S-006P" 9V

(IEC DESIGNATION 6F22)

KEEP THE CORRECT

TIME DURING POWER

STOPPAGE

SP MODEL

PS101

E MODEL

T2

AC IN ~

TRANSFORMER
BOARD

11 11

ICF-C111

5-2. PRINTED WIRING BOARD • Refer to page 10 for Common Note on Printed Wiring Boards.

A

B

C

D

E

F

G

H

1

w VOLUME

LED102
ALARM

VR1

2 3 4 5 6 7 8 9 10 11 12 13 14 15

• Semiconductor
Location

Ref. No. Location
D101 F-6

D201 H-9
D202 H-9
D203 D-9
D204 H-5
D205 H-5

IC1 D-5
IC101 H-7

LED101 I-6
LED102 I-2

Q1 G-2
Q201 F-9
(Q202) D-9

( ) : E MODEL

11

1-680-065-

(11)

AC IN ~

R107

BE

R106

MAIN BOARD

TUNING

C20

CV1-1 CV1-3

CT3

CT1

CT2

CV1-2 CV1-4

C1

S1

BAND

FM

AM

JW7

Q1

C

R104

C107

JW102

C6

CV1

CT4

FM LEAD WIRE

ANTENNA

BLK RED

WHT

BPF1

L3

C2

R6

L4

R5

L2

JW5

S7

SLEEP

C3

R210

JW209

C8

R2

C210

C205

CF1

R103

D205

SNOOZE/

SLEEP OFF

JW101

R209

L1

AM FERRITE-ROD

ANTENNA

CF3

R1
15 16

10

5

1

D204

C5

C7

S5

ALARM

S8

IC1

C19

C204

C11C12

D101

C104

R204

20

25

C14

30

R105

JW3

C16

R212

CF2

C9

R213

R4

-2

-1

C10

C13

C15

S3

TIME SET

M

R214

T1

JW207

JC105

ALARM

BUZZER RADIO RADIO ON OFF

S2

JW201

C18

C207

S4

TIME SET

H

IC101

C102

R120

SP MODEL

51014

252015

C103

R101

JC101

28

C101

1

JC102

15101517

S2

(Function Selector)

JW204

JW203

R205

JW104

C206

JW206

C202

R206

C201

W703

SP MODEL

JC103

EB

Q201

C203

D202

D201

Q202

C

JW202

S6

CLOCK

JW205

CN701

1

3

6

1-680-064-

BLK

RED

D203

4

3
2

1

DRY BATTERY

"S-006P" 9V

(IEC DESIGNATION 6F22)

KEEP THE CORRECT

TIME DURING POWER

STOPPAGE

E MODEL

SP1

(SPEAKER)

11

(11)

1
2
3
4

T2

POWER

TRANSFORMER

TRANSFORMER BOARD

SP MODEL

PS101

W701

TLM1 TLM2

E MODEL

E MODELSP MODEL SP MODEL

I

(SHIELD)

LED101

J

1212

5-3. SCHEMATIC DIAGRAM • Refer to page 10 for Common Note on Schematic Diagram and page 14 for IC Block Diagrams.

IC B/D

ICF-C111

IC B/D

(Function Selector)

13 13

ICF-C111

SECTION 6

EXPLODED VIEWS

• IC Block Diagrams

IC1 CXA1019S

GND

GND

AF OUT+BRIPPLE

FILTER

AF IN

DET OUT

AFC (J)AGC

AFC (W)AGC

23 22 21 202425 19 18 17 1629 28 27 2630

AM IF DET AGC

AF POWER AMP AM FE FM IF

FM

DISCRIMINATOR

FM FE

2 3

1

GND

GND

5 6 7 8 9

4

NF

VOL

DISCRI

AFC

AM OSC

10

REG

FM OSC

IF GND

TUNING

METER

FM RF

LED

11

AM ANT

NOTE:

• The mechanical parts with no reference
number in the exploded views are not supplied.

• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.

NC

FM IF IN

AM IF IN

BAND SW

• Abbreviation
SP : Singapore model

• Color Indication of Appearance Parts
Example :

KNOB, BALANCE (WHITE) ... (RED)

R

Parts Color Cabinet’s Color

• Accessories and packing materials are
given in the last of this parts list.

R

The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.

6-1. CABINET (UPPER) SECTION

1

3

15141312

NC

FE GND

FM ANT

MIX OUT

9

5

IC101 LM8560N

12/24 HR

SELECT

28 27 26 25 24 23 22 21 20 19 18 17 16 15

STAND

BY DET

50/60Hz

1/25 or 1/30

2Hz

1Hz

BLANK &

FLASH

PF.

DET

1 2 3 4 5 6 7 8 9 10 11 12 13 14

S

,

AM & 10

CR/INPUT

OSC

CTR

GATE

1/2

SEC
CTR

GATE

S HR B

,

HR AG & DE

PM & 10

50/60 Hz

SELECT

50/60 Hz

INPUT

ALARM

MIN CTR

COMPARATOR SLEEP CTR

TIME

MIN CTR

HR B & G

S HR C & HR B

,

10

SLEEP

INPUT

SNOOZE

INPUT

D

ALARM

HR CTR

HR CTR

OUTPUT DECODER/DRIVER

HR A & F

HR C & D

HOUR SET

D DD D D

INPUT

CONTROL

RESET

CONTROL

F.SAMPLE

TIME

S MIN A & F

,

10

S MIN B & G

,

,

10

S MIN C & D
10

MIN SET

S.SAMPLE

S MIN E

,

10

VSS

DISPLAY

CONTROL

PWR UP

& MIN E

MIN B & G

ALARM

DISP

OUTPUT

CONTROL

CONTROL

MIN C & D

ALARM

OFF

MIN A & F

SLEEP OUT

ALARM OUT

SLEEP

SEC,TIME,ALARM

COLON OUTPUT

VDD

2

4

Ref. No. Part No. Description Remark

1 3-226-587-01 KNOB (FUNCTION) (BLACK)
1 3-226-587-11 KNOB (FUNCTION) (WHITE)
2 3-226-584-01 PANEL (FRONT) (E)
2 3-226-584-11 PANEL (FRONT) (SP)
3 X-3380-019-1 UPPER ASSY, CABINET (BLACK) (E)

3 X-3380-019-2 UPPER ASSY, CABINET (WHITE) (E)
3 X-3380-020-1 UPPER ASSY, CABINET (BLACK) (SP)
3 X-3380-020-2 UPPER ASSY, CABINET (WHITE) (SP)

7

6

6

8

Ref. No. Part No. Description Remark

4 7-685-647-79 SCREW +P 3X10 TYPE2 NON-SLIT

0 5 1-555-795-00 CORD, POWER (SP)
0 5 1-769-339-22 CORD, POWER (E)

6 7-685-153-19 SCREW +P 3X30 TYPE2 NON-SLIT
7 3-368-852-01 FOOT

8 3-369-135-21 LID, BATTERY CASE
9 3-515-102-31 CUSHION

1414

6-2. CABINET (LOWER) SECTION

ICF-C111

LED101

SP1

52

54

W703

T2

62

54

53

L1

54

54

55

56

63

58

57

59

60

61

not supplied

51

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

51 3-226-583-01 CABINET (LOWER) (BLACK) (E)
51 3-226-583-11 CABINET (LOWER) (WHITE) (E)
51 3-226-583-21 CABINET (LOWER) (BLACK) (SP)
51 3-226-583-31 CABINET (LOWER) (WHITE) (SP)

* 52 1-680-065-11 TRANSFORMER BOARD

53 1-535-804-21 SNAP, BATTERY
54 7-685-647-79 SCREW +P 3X10 TYPE2 NON-SLIT

* 55 1-680-064-11 MAIN BOARD

56 3-226-590-01 HOLDER (ANTENNA)
57 3-933-547-01 SHEET (BAND)

59 3-226-589-01 POINTER
60 3-919-268-01 KNOB (VOL) (BLACK)
60 3-919-268-11 KNOB (VOL) (WHITE)
61 3-226-585-01 CHASSIS (E)
62 3-553-567-00 CUSHION

63 1-754-135-11 ANTENNA (WIRE)
LED101 8-749-016-86 LED SL-3998-78T (E)
LED101 8-749-016-87 LED SL-3998-79T (SP)
SP1 1-529-456-11 SPEAKER (6.6cm)

0 T2 1-433-573-11 TRANSFORMER, POWER (E)

The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.

58 3-226-588-01 KNOB (TUNING) (BLACK)
58 3-226-588-11 KNOB (TUNING) (WHITE)

0 T2 1-433-574-21 TRANSFORMER, POWER (SP)

W703 1-757-686-11 CORD, CONNECTION (17 CORE)

15

ICF-C111

SECTION 7

MAIN

NOTE:

• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.

• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

* 1-680-064-11 MAIN BOARD

***********

1-535-804-21 SNAP, BATTERY
1-754-135-11 ANTENNA (WIRE)
3-226-590-01 HOLDER (ANTENNA)
7-685-647-79 SCREW +P 3X10 TYPE2 NON-SLIT

ELECTRICAL PARTS LIST

• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.

• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..

• CAPACITORS
uF : µF

• COILS
uH : µH

CF1 1-781-861-71 FILTER, CERAMIC (COMBINATION)
CF2 1-781-790-11 FILTER, AM CERAMIC
CF3 1-781-861-71 FILTER, CERAMIC (COMBINATION)

The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.

When indicating parts by reference
number, please include the board.

• Abbreviation
SP : Singapore model

< FILTER >

< CONNECTOR >

< BPF >

BPF1 1-236-022-11 FILTER, BAND PASS

< CAPACITOR >

C1 1-162-936-11 CERAMIC CHIP 5PF 0.25PF 50V
C2 1-164-160-11 CERAMIC CHIP 20PF 5% 50V
C3 1-164-405-11 CERAMIC CHIP 27PF 5% 50V
C5 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C6 1-104-664-11 ELECT 47uF 20% 10V

C7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C8 1-126-960-11 ELECT 1uF 20% 50V
C9 1-126-963-11 ELECT 4.7uF 20% 50V
C10 1-126-964-11 ELECT 10uF 20% 50V
C11 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V

C12 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C13 1-126-964-11 ELECT 10uF 20% 50V
C14 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C15 1-126-924-11 ELECT 330uF 20% 10V
C16 1-109-982-11 CERAMIC CHIP 1uF 10% 10V

C18 1-104-665-11 ELECT 100uF 20% 10V
C19 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C20 1-162-907-11 CERAMIC CHIP 2PF 0.25PF 50V
C101 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V
C102 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C103 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C104 1-164-361-11 CERAMIC CHIP 0.047uF 16V
C107 1-126-961-11 ELECT 2.2uF 20% 50V
C201 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C202 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

* CN701 1-568-272-11 SOCKET, CONNECTOR 6P

< VARIABLE CAPACITOR >

CT1-4 1-141-522-11 CAP, VAR
CV1 1-141-522-11 CAP, VAR (TUNING)

< DIODE >

D101 8-719-911-19 DIODE 1SS119-25
D201 8-719-911-19 DIODE 1SS119-25
D202 8-719-052-88 DIODE 1N4002
D203 8-719-911-19 DIODE 1SS119-25
D204 8-719-911-19 DIODE 1SS119-25

D205 8-719-911-19 DIODE 1SS119-25

< IC >

IC1 8-752-037-02 IC CXA1019S
IC101 8-759-821-46 IC LM8560N

< JUMPER RESISTOR >

JC101 1-216-864-11 SHORT 0 (SP)
JC102 1-216-864-11 SHORT 0 (SP)
JC103 1-216-864-11 SHORT 0 (SP)
JC105 1-216-864-11 SHORT 0

< COIL >

L1 1-419-532-11 COIL, FERRITE-ROD ANTENNA (AM)
L2 1-419-533-11 COIL, OSCILLATION (AM)

* L3 1-422-320-11 COIL, AIR-CORE

L4 1-422-131-00 COIL, FM OSCILLATION

C203 1-126-934-11 ELECT 220uF 20% 16V
C204 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C205 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C206 1-126-935-11 ELECT 470uF 20% 10V
C207 1-126-935-11 ELECT 470uF 20% 10V

C210 1-126-933-11 ELECT 100uF 20% 16V

16

< DIODE >

LED101 8-749-016-86 LED SL-3998-78T (E)
LED101 8-749-016-87 LED SL-3998-79T (SP)
LED102 8-719-054-61 LED SLR-342VRTJ7 (ALARM)

< TRANSISTOR >

Q1 8-729-216-22 TRANSISTOR 2SA1162-G

ICF-C111

MAIN TRANSFORMER

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

Q201 8-729-011-92 TRANSISTOR 2SC2001TP-K1K2
Q202 8-729-216-22 TRANSISTOR 2SA1162-G (E)

* 1-680-065-11 TRANSFORMER BOARD

********************

< RESISTOR >

R1 1-216-815-11 METAL CHIP 330 5% 1/16W
R2 1-216-805-11 METAL CHIP 47 5% 1/16W
R4 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R5 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R6 1-216-821-11 METAL CHIP 1K 5% 1/16W

R101 1-216-849-11 METAL CHIP 220K 5% 1/16W
R102 1-216-845-11 METAL CHIP 100K 5% 1/16W
R103 1-216-845-11 METAL CHIP 100K 5% 1/16W
R104 1-216-841-11 METAL CHIP 47K 5% 1/16W
R105 1-216-835-11 METAL CHIP 15K 5% 1/16W

R106 1-216-815-11 METAL CHIP 330 5% 1/16W
R107 1-216-832-11 METAL CHIP 8.2K 5% 1/16W
R204 1-216-801-11 METAL CHIP 22 5% 1/16W
R205 1-216-821-11 METAL CHIP 1K 5% 1/16W
R206 1-249-409-11 CARBON 220 5% 1/4W

R209 1-249-389-11 CARBON 4.7 5% 1/4W
R210 1-249-389-11 CARBON 4.7 5% 1/4W
R212 1-216-833-11 METAL CHIP 10K 5% 1/16W
R213 1-216-833-11 METAL CHIP 10K 5% 1/16W
R214 1-216-833-11 METAL CHIP 10K 5% 1/16W

< SWITCH >

S1 1-692-181-21 SWITCH, SLIDE (BAND)
S2 1-771-904-11 SWITCH, SLIDE (Function selector)
S3 1-692-014-11 SWITCH, KEYBOARD (TIME SET M)
S4 1-692-014-11 SWITCH, KEYBOARD (TIME SET H)
S5 1-692-014-11 SWITCH, KEYBOARD (ALARM)

S6 1-692-014-11 SWITCH, KEYBOARD (CLOCK)
S7 1-692-014-11 SWITCH, KEYBOARD (SLEEP)
S8 1-692-014-11 SWITCH, KEYBOARD (SNOOZE/SLEEP OFF)

0 1-555-795-00 CORD, POWER (SP)
0 1-769-339-22 CORD, POWER (E)

< IC LINK >

0 PS101 1-533-971-11 LINK, IC (200mA) (SP)

< TRANSFORMER >

0 T2 1-433-573-11 TRANSFORMER, POWER (E)
0 T2 1-433-574-21 TRANSFORMER, POWER (SP)

< TERMINAL >

* TLM1 1-535-771-11 TERMINAL (SP)
* TLM2 1-535-771-11 TERMINAL (SP)
*************************************************************

MISCELLANEOUS

***************

0 5 1-555-795-00 CORD, POWER (SP)
0 5 1-769-339-22 CORD, POWER (E)

53 1-535-804-21 SNAP, BATTERY
SP1 1-529-456-11 SPEAKER (6.6cm)

*************************************************************

ACCESSORIES & PACKING MATERIALS

********************************

3-227-320-01 SHEET (BLIND) (BLACK) (E)
3-227-320-11 SHEET (BLIND) (WHITE) (E)
3-227-587-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH,

GERMAN,SPANISH,DUTCH,ITALIAN) (E)

3-227-587-41 MANUAL, INSTRUCTION (ENGLISH,

SIMPLIFIED CHINESE,POLISH,CZECH,

HUNGARIAN,SLOVAKIAN) (SP)

< TRANSFORMER >

T1 1-435-399-11 TRANSFORMER, IF

< VARIABLE RESISTOR >

VR1 1-228-790-00 RES, VAR, CARBON 50K (VOLUME)

< CONNECTION CORD >

W703 1-757-686-11 CORD, CONNECTION (17 CORE)

*************************************************************

The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.

17

ICF-C111

REVISION HISTORY

Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.

Ver. Date Description of Revision

1.0 2001. 03 New

18