Sony ICD-00PC Service Manual

ICD-R100PC

SERVICE MANUAL

Ver 1.0 1999.05

SPECIFICATIONS

US Model

Canadian Model

AEP Model

Connection cable x 1
Froppy disc x 3

IC RECORDER

MICROFILM

TABLE OF CONTENTS

d

Specifications ........................................................................... 1

1. SERVICING NOTE....................................................... 2

2. GENERAL ....................................................................... 3

SECTION 1

SERVICING NOTE

Using the special connector jig (J-2503-101-A) to connect the main
board and digital board will prove convenient when servicing the
unit with power applied.

3. DISASSEMBLY

3-1. Lid ASSY, Upper ........................................................ 5

3-2. Digital Board .............................................................. 5

3-3. Unit, Switch ................................................................ 6

3-4. Jack Board .................................................................. 6

3-5. Main Board ................................................................. 6

4. DIAGRAMS

4-1. Explanation of IC Terminals....................................... 7

4-2. Block Diagrams .......................................................... 9

4-3. Printed Wiring Boards (Main Section) ......................11

4-4. Schematic Diagram (Main Section) ......................... 13

4-5. Printed Wiring Boards (Digital Section) .................. 17

4-6. Schematic Diagram (Digital Section)....................... 18

5. EXPLODED VIEWS

5-1. Case Section ............................................................. 23

5-2. Main Board Section .................................................. 24

6. ELECTRICAL PARTS LIST .................................... 25

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270°C during
repairing.

• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or
unsoldering.

Notes on chip component replacement

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be dam­aged by heat.

Jig (J-2503-010-A)

Digital board

Main boar

Note : Do not apply excessive amounts of flux during replace-

ment of electronic components since this may cause elec­trical shorts due to moisture.
Wipe off flux after electronic components exchange.

CAUTION ON REPLACING FLASH MEMORY

The BAD-BLOCK check* must be executed, when the flash
memory (IC701) in this set was replaced.
The set will not operation normally, unless this check is finished.

* The BAD-BLOCK check detects an area (bad-block) in the flash

memory where data validity cannot be guaranteed, and saves
this information in the TOC-AREA so that a bad-block is not
used.

BAD-BLOCK check procedure :

1. Apply 3V from regulated power supply to the battery
terminals.

2. Once the power is supplied, the check starts and then
proceeds for approx. 3 minutes. (Be sure to keep applying
the power during the check)

3. When the check completes, the result is shown as bellows.
OK: Only the LCD back light LED (D503, 504) turns on.
NG: Red LED blinks or turns on or green LED turns on in

the OPR LED (D502),

4. In case of OK, press the STOP button.

Note :

• In case of NG, check system control IC (IC704), flash memory
IC (IC701) and the peripheral circuit. (Particularly, check care­fully the soldering of the flash memory)

• After finishing the BAD-BLOCK check, assemble the set, load
the dry battery, and confirm if the set operates normally.

– 2 –

LOCATION AND FUNCTION OF CONTROLS

SECTION 2

GENERAL

This section is extracted from
instruction manual.

– 3 –

– 4 –

SECTION 3

)

DISASSEMBLY

r

The equipment can be removed using the following procedure.

Set

Note : Follow the disassembly procedure in the numerical order given.

3-1. LID ASSY, UPPER

Lid ASSY, Upper

Digital board Jack board Main board

Unit, Switch

4

Lid ASSY, Upper

1

Screw (B1.7X10

3

Remover solder

3-2. DIGITAL BOARD

2

Case ASSY

2

Screws (B1.7X9)

Note : Not using a screw (10mm) of step

1 for this place.

Digital board

Remove the

1

connector
(CN703)

– 5 –

Case ASSY

d

Y

d

3-3. UNIT, SWITCH

e

3-4. JACK BOARD

Digital board

1

1

Screw (B1.7X4)

Unit, Switch

2

Double-sided adhesive tap

Note : The switch unit is secured with double-sided

adhesive tape.
When removed the switch unit, change it for
a new component.

3-5. MAIN BOARD

2

Remove the
connector
(CN102)

4

3

Jack boar

Case ASSY

Cap (Terminal)

Main boar

2

Claw

3

Claw

1

Case ASS

Cap (PC)

– 6 –

SECTION 4

DIAGRAMS

4-1. EXPLANATION OF IC TERMINALS

IC704 µPD780308GC-113-8EU (SYSTEM CONTROL)

Pin No. Pin name I/O Description

1 KEY0 I Key input
2 KEY1 I Key input
3 SPDSW I Playback speed switch input.
4 XHOLD I Hold switch input.
5 HPMUTE O Earphone mute output.
6 PCLE O PC link permission signal output.
7 XFMCE O CE output for flash memory.
8 VDDO – Power supply terminal.

9 AVREF I A/D reference voltage input.
10 XFMWE O Write enable signal output for flash memory.
11 XFMALE O ALE signal output.
12 VSS1 – Ground.
13 XFMR/B I Flash memory Ready/Busy signal input.
14 XFMCLE O CLE signal output for flash memory.
15 SYNCOUT O SYNC signal output.
16 SYNCMSK O SYNC output control signal output.
17 XFMRE O Flash memory read enable signal output.
18 MSKCLK I SYNC output control clock input.
19 XFMWP O Flash memory WP signal output.
20 XFMSE O Flash memory SE signal output.
21 BEEP O BEEP signal output (2.4kHz).
22 LIGHT O LCD back lignt control output.

23 – 26 COMO 0–3 O LCD common signal output.

27 BIAS – Connect to VCC (LCD BIAS).

28 – 30 VLC 0 – 2 – LCD drive power supply.

31 VSS0 – Ground.

32 – 61 S0 – S29 O LCD segment signal output.

62 XVORSW I VOR switch input.
63 XVORIN I VOR signal input.
64 XTEST I Test terminal.
65 XDSPDEN O DSP registor control I/F enable signal output.
66 LEDREC O REC LED (red) ON/OFF output.
67 LEDPB O PLAY LED (green) ON/OFF output.
68 AMPPOW O Power down control output for IC108.
69 SPOWER O IC101 and analog power supply control output.
70 RTCCE O Real time colck CE signal output.
71 XPDRST O Reset signal output for IC101.
72 DSPIS I Serial data input from IC101.
73 DSPIR O Playback serial data output for IC101.
74 XBLCK O DSP bit clock signal output.
75 RTCDI I Real time colck data input.
76 RTCDO O RTC data and DSP registor contrl data output.
77 RTCCLK O RTC I/F data and DSP registor control clock output.
78 IC – Ground.
79 X2 O System clock output (5MHz).
80 X1 I System clock input (5MHz).

– 7 –

Pin No. Pin name I/O Description

81 VDD1 – Power supply terminal.
82 XT1 I Sub clock input.
83 XT2 I Sub clock turn over input.
84 XRESET I Reset signal input.
85 PCLINK I PC link connection detect input.
86 WAKEUP I WAKE UP signal input.
87 RTCINT I Real time clock (2Hz) signal input.
88 FLMPOW O Flash memory and IC707 power ON/OFF.
89 LPMODE O LPF switch control output.
90 LMUTE O Line mute ON/OFF signal output.

91 – 98 FMIO 0 – 7 I/O Data bus.

99 AVSS – A/D converter ground.

100 BATT I Power supply voltage detect input.

– 8 –

4-2. BLOCK DIAGRAMS

ICD-R100PC

– 9 – – 10 –

• Signal path.

F : PLAY
L : REC

ICD-R100PC

r

Semiconductor

Location

Ref. No. Location
D501 F-5

IC101 C-6
IC102 C-5
IC103 B-2
IC104 C-2
IC105 D-2

IC106 C-6
IC107 D-6
IC108 G-2
IC109 B-6
IC502 G-5

IC503 E-5
IC504 B-5
IC506 H-5
IC705 F-6
IC707 E-2

IC708 E-2
IC709 D-3
IC710 C-2
IC777 D-6

Q101 G-5
Q102 H-5
Q103 B-3
Q105 F-2
Q108 B-5

Q109 F-2
Q110 D-2
Q502 B-3
Q704 D-3
Q777 D-2

4-3. PRINTED WIRING BOARDS (MAIN SECTION)

1 2 3 4 5 6 7 8 910

A

[MAIN BOARD]
(SIDE A)

FB102

B

C

C162

D

E

F

G

H

C148

R110

C108

R139

5

8

C112

R132

R137

02

R164

R121

C125

C131

Q105

C155

R153

R154

C161

C105

R134

5

8

R142

R118

C156

R138

IC105

Q110

R152

4

IC108

5

IC103

R167

C157

R131

17

20

25

30
32

C718

C149

R163

R751

C717

1

8

C126
C127

4

R151

R758

R756

R135

C116

1

IC710

4

1

1

R765

16

33

C722

Q109

RB704

RB705

4

1

C109

C128

35

R111

R133

TP112

IC104

3

Q777

FB701

5

IC708

1

C723

R122

C725

2

10

IC707

40

R732

S714

R102

R157

R166

4

3

S101

OFF ON

C114

R509

1

3

5

45

S713

VOR

R156

R510

8

5

R749

IC709

1

48

FB106

FB104

C139

R143

5

4

50

FB105

C140

R144

Q704

1-673-293-

Q502

R504

R506

C506

64

60

55

49

R105

R724

R140

Q103

C144

R146

R727

R104

FB107

C143

C508

R145

R750

L503

C102

R103

C142

C145

R514

FB101

(IEC DESIGNATION LR03)

SLOW NORMAL FAST

MIC SENS

11

(11)

DRY BATTERY

SIZE "AAA"

2PCS, 3V

S714

PLAY SPEED

S101

L H

[MAIN BOARD]
(SIDE B)

A

DIGITAL BOARD

CN705

(Page 18)

Q101

C510

26

30

35

40

45

50

C513

R515

C110

C512

15

FB103

54

IC102

123

R113

R764

CN703

D501

C505

R107

IC506

45

610

IC504

IC503

4

5

3

17

20

25

30

32

15

10

L501

123

CN102

12

R116

C509

C502

Q102

FB503

R725

C137

Q108

GDS

IC106

R117

25

20

5

1

IC502

1
2
3

C716

45

C130

R511

C710

3

2

1

IC101

R171

R726

R743

5

4

MIC101

MIC

C101

45

IC109

R120

123

8

1

R512

R155

C719

IC705

R755

R752

FB501

R136

IC107

C129

2
3
1

RB702

RB701

C104
R106

C158

123

C133

5

4

R147

R754

R108

R733

C724

15

10

R160

R753

R141

R763

5

1

SPEAKER

C160

C118

16

C152

C141

C134

R149

R762

R148

1
2
34

IC777

C730

C153

1-673-293-

C151

SP101

C147

10

5

1

C107

R161

R150

C146

C154

C103

R109

C111

R112

5

RV101

∑VOL

CN701

C124

C106

C136

R761

R162

CN701

DIGITAL I/O

11

(11)

CN101

5

1

[JACK BOARD] (SIDE A)

J102

EAR

6

(PLUG-IN POWER)

10

1-673-294-

11

(11)

[JACK BOARD] (SIDE B)

1-673-294-

Note:

• X : parts extracted from the component side.

®

•

: Through hole.

• b : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)

Caution:

Pattern face side: Parts on the pattern face side seen from the
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.

11

(11)

J101

MIC

– 11 – – 12 –

4-4. SCHEMATIC DIAGRAM (MAIN SECTION)

p

r

Refer to page 21 for IC Block Diagrams.

r

Waveforms

1

ICD-R100PC

4.1 Vp-p

91.4 kHz

IC503 4

VOLT/DIV : 1 V AC
TIME/DIV : 2 µsec

2

3.5 Vp-p

REC 11 kHz
PLAY 13 kHz

IC102 3

VOLT/DIV : 1 V AC
TIME/DIV : 20 µsec

3

1.7 Vp-

14kHz

IC102 4

Note:

• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.

• All resistors are in Ω and 1/
specified.

• U : B+ Line.

• Power voltage is dc 3V and fed with regulated dc power
supply from battery terminal.

• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : REC
( ) : PLAY

• Voltages and current are taken with a V OM (Input imped­ance 10 MΩ).
Voltage variations may be noted due to normal produc­tion tolerances.

• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc­tion tolerances.

• Circled numbers refer to waveforms.

• Signal path.

F : PLAY
L : REC

VOLT/DIV : 5 V AC
TIME/DIV : 20 µsec

4

W or less unless otherwise

– 13 – – 14 – – 16 –– 15 –

ICD-R100PC

p

p

4-5. PRINTED WIRING BOARDS (DIGITAL SECTION)

1 2 3 4 5 6

[DIGITAL BOARD] (SIDE A)

5

R505

FB702

R766

R507

1

2

Q503

IC505

R508

CN702

15

25

1510152024

R737

R744

D701

R701

R728

R719

SWITCH UNIT

DISPLAY MENU STOP

”PLAY/STOP

=REVIEW/– +CUE/+

A

R711

R712

D503

R715

D504

LCD BACK LIGHT

B

LCD101

LIQUID CRYSTAL DISPLAY

C

D

R702

IC701

E

25 30 35 40 45 48

IC703

13

R713

2

3

1

4

2

F

45

IC702

Q703

R714

G

02

Q501

R722

BP701

R747

C709

1

3

1

5

10

20

30

C715

34

CN704

1-673-292-

D502

OPR

D502

S702

R721

6

R513

S703

R731

R729

R503

R720

11

(11)

S711

P PAUSE

S703

INDEX

S702

FILE

S712

HOLD

ON

OFF

ERASE

[DIGITAL BOARD] (SIDE B)

S711

S701

IC501

S712

R734

S704

S704

JC701

R730

rREC/STOP

C504

R501

R502

C727

51

55

60

C501
65

70

75

JC702

R739

S701

76 80 85 90

X702

IC706

5

X701

6

C708

C701

1

10

C704

C702

1-673-292-

C726

R740

R741

Q701

IC704

C711

R742

R738

15

95

FB703

CN705

25

20

10

5

1

C712

26

30

35

40

45

50

Q702

100

R703

R704

263035404550

R723

C721

20

10

25

15

5

1

R745

A

11

(11)

r

Semiconductor

Location

Ref. No. Location
D502 A-3

D503 B-1
D504 B-2
D701 E-2

IC501 C-4
IC505 A-2
IC701 E-2
IC702 F-1
IC703 F-2

IC704 C-5
IC706 E-5

Q501 A-2
Q503 A-2
Q701 F-5
Q702 F-6
Q703 F-1

MAIN BOARD

CN703

(Page 11)

Note on Printed Wiring Boards:
Note:

• X : parts extracted from the component side.

¢

•

•

• b : Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)
Caution:

Pattern face side: Parts on the pattern face side seen from the
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.

: internal component.

®

: Through hole.

4-6. SCHEMATIC DIAGRAM (DIGITAL SECTION)

r

Refer to page 22 for IC Block Diagrams.

r

Wavef orms

1

IC704 &ª

2

IC706 8

1.3 Vp-

5 MHz

VOLT/DIV : 0.5 V AC
TIME/DIV : 50 nsec

438 mVp-

32.768 kHz

VOLT/DIV : 0.1 V AC
TIME/DIV : 10 µsec

4

REC 11 kHz
PLAY 13 kHz

IC704 !§

5

32.768 kHz

IC704 *™

3

3.5 Vp-p

REC 11 kHz
PLAY 13 kHz

IC704 !∞

Note:

• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.

• All resistors are in Ω and 1/
specified.

¢

•

• U : B+ Line.

• Power voltage is dc 3V and fed with regulated dc power

• Voltages and waveforms are dc with respect to ground

• Voltages and current are taken with a V OM (Input imped-

• Waveforms are taken with a oscilloscope.

• Circled numbers refer to waveforms.

: internal component.

supply from battery terminal.
under no-signal conditions.

no mark : REC
( ) : PLAY

ance 10 MΩ).
Voltage variations may be noted due to normal produc­tion tolerances.

Voltage variations may be noted due to normal produc­tion tolerances.

VOLT/DIV : 1 V AC
TIME/DIV : 20 µsec

4

W or less unless otherwise

3.5 Vp-p

VOLT/DIV : 1 V AC
TIME/DIV : 20 µsec

0.8 Vp-p

VOLT/DIV : 0.2 V AC
TIME/DIV : 10 µsec

– 19 – – 20 –– 17 – – 18 –

r

IC Block Diagrams (MAIN SECTION)

IC101 MSM7590L-01TS-K

1

AG

REFERENCE

POWER SUPPLY

+
–

–
+

PCM

ENCODER

AIN1+

AIN1–

GSX1

AIN2

SG

2

3

4

5

6

ADPCM

ENCODER

DG

32

BCLK

31

XSYNC

30
29

RSYNC

GSX2

7

8

VFRO

PWI

AOUT–

AOUT+

SAO+

SAO–

PDN/RESET

VOXI

VDD

9

10

11

12

13

14
15
16

–
+

–1

+1

–1

IC102 XC25A08510MR

CE

5

CLKOUT

4

BUFFER

ATT

DECODER

BACK-GROUND

GENERATOR

ATT

PCM

NOISE

DTMF/

OTHERS TONE

GENERATOR

VOICE

DETECT

P/S

or

S/P

ADPCM

DECODER

CLOCK,

TIMING

GENERATOR

INTERFACE

IC104 NJM2072M

INPUT

GAIN CONT

CPU

PCMSO

28

PCMSI

27

IS

26

IR

25
24

PCMRO
PCMRI

23

MCK

22

DEN

21

EXCK

20

DIN

19

DOUT

18

VOXO

17

1

2

8

7

VCC

OUTPUT2

21 3

CLKINVSS VDD

1/2

VCO

L.P.F.

PHASE

DETECTOR

1/N

COUNTER

AMP OUT

3

GND

4

IC709 TC7S08FU (TE85R)



5

IN B
IN A
GND

1
2
3

VCC

4

OUT Y

– 21 –

OUTPUT1

6

RECOVERY

5

TIME CAP

IC503 XC6372C381PR

SLOW
START

REFERENCE

VDD

CHIP

ENABLE



VOLTAGE

5
4

COMPARATOR

VCC
OUT Y

PHASE

–
+

1

NC

2

VOUT

CE

3

r

IC Block Diagrams (DIGITAL SECTION)

IC702 TC7S08FU (TE85R)

IN B

1
2

IN A

3

GND

VLX

LIMITER

PWM/PFM

CONTROL

OSC 100kHz

BUFFER

VSS

5

LX

4

IC706 RS5C348A-E2

32KOUT

1

SCLK

2

SO

3

4

SI

5

VSS

32 kHz

OUTPUT

CONTROL

I/O

CONTROL

COMPARATOR

COMPARATOR

ADDRESS
REGISTER

SHIFT

REGISTER

ALARM W REGISTER

ADDRESS
DECODER

INTERRUPT

CONTROL

VOLTAGE

DETECT

(WEEK, MIN, HOUR)

ALARM D REGISTER

W

D

TIMER COUNTER

SEC, MIN, HOUR, WEEK,

DAY, MONTH, YEAR

(MIN, HOUR)

DIV

DIVIDER

CORRECTION

OSC

DETECT

OSC

VDD

10

9

8

7

6

VDD

OSCIN

OSCOUT

CE

INTR

– 22 –

NOTE :

• -XX, -X mean standardized parts, so they
may have some difference from the original
one.

• Items marked “ * ”are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.

5-1. CASE SECTION

SP101

SECTION 5

EXPLODED VIEWS

• The mechanical parts with no reference
number in the exploded views are not
supplied.

• Aaccessories and packing materials are given
in the last of this parts list.

13

16

15

15

20

16

19

18

17

23

14

8

10

7

9

8

12

21

6

11

5

3

22

not supplied

4

1

2

Note: Not using a screw (10mm)

of No.22 for this place.

Note: Not using a screw (10mm)

2

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

1 4-217-035-01 CAP (PC)
2 3-318-203-91 SCREW (B1.7X9), TAPPING
3 4-217-034-01 LID, BATTERY CASE
4 X-4951-074-1 CASE ASSY
5 4-220-198-01 CUSHION (BATT)

6 4-221-482-01 SPACER (CLIP)
7 X-4951-795-1 CLIP ASSY
8 3-349-859-41 WASHER
9 4-217-036-01 CLIP
10 4-217-864-01 SHAFT (CLIP)

11 4-221-241-01 WASHER (P)
12 4-217-037-01 SPRING (CLIP)

of No.22 for this place.

13 X-4951-072-1 LID ASSY, UPPER
14 3-375-114-41 SCREW
15 4-217-032-01 BRACKET (SPEAKER)

16 4-221-238-01 SHEET (BUTTON)
17 4-220-916-01 SHEET (LED)
18 4-221-239-01 SHEET (STOP)
19 4-221-237-01 CUSHION (LCD)
20 4-221-236-01 CUSHION (PC)

21 4-221-616-01 SPACER (TERMINAL)
22 3-334-565-01 SCREW (B1.7X10), TAPPING
23 3-318-382-71 SCREW (1.7X4), TAPPING
SP101 1-505-854-11 SPEAKER (2.8cm)

– 23 –

5-2. MAIN BOARD SECTION

67

57

56

75

71

59

69

58

77

68

66

61

72

62

70

73

74

LCD101

76

60

63

MIC101

64

65

54

55

53

52

51

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

51 A-3321-888-A MAIN BOARD, COMPLETE
52 4-221-243-01 CUSHION, RUBBER
53 4-220-920-01 SPACER (P2)
54 4-220-922-11 SHEET (F)
55 4-217-039-01 TERMINAL (-), BATTERY

56 4-217-038-01 TERMINAL (+), BATTERY
57 4-217-040-01 CAP (TERMINAL)
58 4-221-344-01 SPACER (FLASH)
59 A-3321-891-A DIGITAL BOARD, COMPLETE
60 4-218-348-01 SHEET (MICROPHONE)

61 4-221-241-11 WASHER (P)
62 4-220-924-01 SHEET (H)
63 4-220-200-01 SHEET (MICROPHONE), ADHESIVE
64 4-219-466-01 SPACER (P)

* 65 1-673-294-11 JACK BOARD

66 4-220-918-01 SPACER (HOLDER LR)
67 3-016-413-21 SHEET (SW)
68 1-418-318-11 UNIT, SWITCH
69 4-217-031-01 HOLDER, LCD
70 4-220-917-01 SPACER (HOLDER 2)

71 4-220-199-01 SHEET (HOLDER)
72 4-220-919-01 SHEET (HOLDER LR)
73 4-220-921-01 SHEET (SW)
74 4-220-141-01 SHEET (BL)
75 4-220-197-01 SPACER (HOLDER)

76 1-694-521-11 CONDUCTIVE BOARD, CONECTION
77 4-218-499-01 PLATE, LIGHT GUIDE
LCD101 1-803-522-11 DISPLAY PANEL, LIQUID CRYSTAL
MIC101 1-542-384-11 MICROPHONE, ELECTRET CONDENSER

– 24 –

SECTION 6

ELECTRICAL PARTS LIST

NOTE :

• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.

• -XX, -X mean standardized parts, so they
may have some difference from the original
one.

• RESISTORS
All resistors are in ohms
METAL : Metal-film resistor
METAL OXIDE :Metal oxide-film resistor
F : nonflammable

• Items marked “ * ”are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

A-3321-891-A DIGITAL BOARD, COMPLETE

**********************

1-418-318-11 UNIT,SWITCH
1-694-521-11 CONDUCTIVE BOARD, CONECTION
4-217-031-01 HOLDER, LCD
4-218-499-01 PLATE, LIGHT GUIDE
4-220-141-01 SHEET (BL)

4-220-197-01 SPACER (HOLDER)
4-220-199-01 SHEET (HOLDER)
4-220-917-01 SPACER (HOLDER 2)
4-220-918-01 SPACER (HOLDER LR)
4-220-919-01 SHEET (HOLDER LR)

4-220-921-01 SHEET (SW)
4-220-922-11 SHEET (F)
4-220-924-01 SHEET (H)
4-221-344-01 SPACER (FLASH)

<CAPACITOR>

C501 1-107-826-11 CERAMIC CHIP 0.1uF 16V
C504 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
C701 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C702 1-104-913-91 TANTAL. CHIP 10uF 20% 16V
C704 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C708 1-113-988-11 TANTAL. CHIP 68uF 20% 4V
C709 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C711 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C712 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C715 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C721 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C726 1-162-921-91 CERAMIC CHIP 33PF
C727 1-162-921-91 CERAMIC CHIP 33PF

<CONNECTOR>

* CN704 1-785-876-21 CONNECTOR, FPC
* CN705 1-785-874-21 PLUG, BOARD TO BOARD 50P

<DIODE>

D502 8-719-073-33 LED CL-165HR/YG-D-T (OPR)
D503 8-719-070-68 DIODE CL-220YG-C-TS (LCD BACK LIGHT)
D504 8-719-070-68 DIODE CL-220YG-C-TS (LCD BACK LIGHT)
D701 8-719-016-74 DIODE 1SS352

• SEMICONDUCTORS

In each case, u : µ , for example :

uA.... : µ A.... , uPA.... : µ PA....

uPB.... : µ PB.... , uPC.... : µ PC....

uPD.... : µ PD....

• CAPACITORS

uF : µ F

• COILS

uH : µ H

FB702 1-414-921-11 INDUCTOR CHIP
FB703 1-414-921-11 INDUCTOR CHIP

JC701 1-216-864-11 METAL CHIP 0 5% 1/16W
JC702 1-216-864-11 METAL CHIP 0 5% 1/16W

IC501 8-759-333-42 IC XC61AN3002MR
IC505 8-759-497-27 IC XC62AP2102MR
IC701 8-759-583-36 IC KM29U128T
IC702 8-759-058-62 IC TC7S08FU(TE85R)
IC703 8-759-058-58 IC TC7S04FU(TE85R)

IC704 8-759-579-98 IC uPD780308GC-113-8EU
IC706 8-759-560-17 IC RS5C348A-E2

LCD101 1-803-522-11 DISPLAY PANEL, LIQUID CRYSTAL

Q501 8-729-426-25 TRANSISTOR XP1212
Q503 8-729-402-32 TRANSISTOR 2SD1819A-R
Q701 8-729-037-74 TRANSISTOR UN9213J-(TX).SO
Q702 8-729-420-24 TRANSISTOR 2SB1218A-QRS
Q703 8-729-420-24 TRANSISTOR 2SB1218A-QRS

R501 1-216-845-11 METAL CHIP 100K 5% 1/16W
R502 1-216-821-11 METAL CHIP 1K 5% 1/16W
R503 1-216-817-11 METAL CHIP 470 5% 1/16W
R505 1-216-821-11 METAL CHIP 1K 5% 1/16W
R507 1-216-833-91 RES,CHIP 10K 5% 1/16W

R508 1-216-793-11 RES,CHIP 5 5% 1/16W
R513 1-216-809-11 METAL CHIP 100 5% 1/16W
R701 1-216-845-11 METAL CHIP 100K 5% 1/16W
R702 1-216-845-11 METAL CHIP 100K 5% 1/16W
R703 1-216-857-11 METAL CHIP 1M 5% 1/16W

R704 1-216-854-11 METAL CHIP 560K 5% 1/16W
R711 1-216-849-11 METAL CHIP 220K 5% 1/16W
R712 1-216-849-11 METAL CHIP 220K 5% 1/16W
R713 1-216-857-11 METAL CHIP 1M 5% 1/16W

When indicating parts by reference num­ber, please include the board.

<FERRITEBEAD>

<JUMPERREGISTOR>

<IC>

<LIQUIDCRYSTALDISPLAY PANEL>

<TRANSISTOR>

<RESISTOR>

DIGITAL

– 25 –

DIGITAL JACK MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R714 1-216-854-11 METAL CHIP 560K 5% 1/16W

C105 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V

R715 1-216-849-11 METAL CHIP 220K 5% 1/16W
R719 1-218-871-11 RES,CHIP 10K 0.50% 1/16W
R720 1-218-875-11 RES,CHIP 15K 0.50% 1/16W
R721 1-216-855-11 METAL CHIP 680K 5% 1/16W
R722 1-216-821-11 METAL CHIP 1K 5% 1/16W

R723 1-216-821-11 METAL CHIP 1K 5% 1/16W
R728 1-216-831-91 METAL CHIP 10K 5% 1/16W
R729 1-218-879-11 RES,CHIP 22K 0.50% 1/16W
R730 1-218-887-11 METAL CHIP 47K 0.50% 1/16W
R731 1-216-855-11 METAL CHIP 680K 5% 1/16W

R734 1-216-833-91 RES,CHIP 10K 5% 1/16W
R737 1-216-853-11 METAL CHIP 470K 5% 1/16W
R738 1-216-833-91 RES,CHIP 10K 5% 1/16W
R739 1-216-833-91 RES,CHIP 10K 5% 1/16W
R740 1-216-833-91 RES,CHIP 10K 5% 1/16W

R741 1-216-833-91 RES,CHIP 10K 5% 1/16W
R742 1-216-845-11 METAL CHIP 100K 5% 1/16W
R744 1-216-853-11 METAL CHIP 470K 5% 1/16W
R745 1-216-821-11 METAL CHIP 1K 5% 1/16W
R747 1-216-845-11 METAL CHIP 100K 5% 1/16W

R764 1-216-845-11 METAL CHIP 100K 5% 1/16W
R766 1-216-857-11 METAL CHIP 1M 5% 1/16W

<SWITCH>

S701 1-771-585-11 SWITCH, PUSH (1 KEY) (r REC/STOP)
S702 1-762-366-11 SWITCH, TACTILE (FILE)
S703 1-762-366-11 SWITCH, TACTILE (INDEX)
S704 1-771-585-11 SWITCH, PUSH (1 KEY) (ERASE)
S711 1-771-248-11 SWITCH, TACTILE (P PAUSE)

S712 1-572-922-11 SWITCH, SLIDE (HOLD)

<VIBRATOR>

* X701 1-767-994-22 VIBRATOR, CRYSTAL (32.768kHz)

X702 1-767-144-21 VIBRATOR, CERAMIC (5MHz)

**************************************************************

* 1-673-294-11 JACK BOARD

***********

<CONNECTOR>

* CN101 1-785-873-21 CONNECTOR, BOARD TO BOARD 10P

<JACK>

J101 1-784-848-21 JACK (MIC (PLUG-IN POWER))
J102 1-785-869-21 JACK (EARPHONE)

**************************************************************

A-3321-888-A MAIN BOARD, COMPLETE

*********************

C106 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C107 1-113-600-11 TANTAL. CHIP 2.2uF 20% 6.3V
C108 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C109 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C110 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C111 1-104-851-11 TANTAL. CHIP 10uF 20% 10V
C112 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C114 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C116 1-164-357-11 CERAMIC CHIP 1000PF 5% 50V
C118 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V

C124 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C125 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C126 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C127 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C128 1-125-926-91 TANTAL. CHIP 4.7uF 20% 6.3V

C129 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C130 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C131 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C133 1-164-357-11 CERAMIC CHIP 1000PF 5% 50V
C134 1-109-847-11 TANTAL. CHIP 0.47uF 20% 16V

C136 1-117-370-11 CERAMIC CHIP 10uF 10V
C137 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C139 1-164-357-11 CERAMIC CHIP 1000PF 5% 50V
C140 1-164-357-11 CERAMIC CHIP 1000PF 5% 50V
C141 1-164-357-11 CERAMIC CHIP 1000PF 5% 50V

C142 1-164-471-11 CERAMIC CHIP 680PF 5% 50V
C143 1-164-471-11 CERAMIC CHIP 680PF 5% 50V
C144 1-164-471-11 CERAMIC CHIP 680PF 5% 50V
C145 1-164-471-11 CERAMIC CHIP 680PF 5% 50V
C146 1-164-360-11 CERAMIC CHIP 0.1uF 16V

* C147 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C148 1-115-156-11 CERAMIC CHIP 1uF 10V
C149 1-109-847-11 TANTAL. CHIP 0.47uF 20% 16V
C151 1-117-370-11 CERAMIC CHIP 10uF 10V
C152 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C153 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V
C154 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V
C155 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C156 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C157 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V

C158 1-113-682-11 TANTAL. CHIP 33uF 20% 10V
C160 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C161 1-162-957-91 CERAMIC CHIP 220PF 5% 50V
C162 1-164-471-11 CERAMIC CHIP 680PF 5% 50V
C502 1-104-851-11 TANTAL. CHIP 10uF 20% 10V

C505 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
C506 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C508 1-117-370-11 CERAMIC CHIP 10uF 10V
C509 1-128-829-91 TANTAL. CHIP 220uF 20% 6.3V
C510 1-104-851-11 TANTAL. CHIP 10uF 20% 10V

<CAPACITOR>

C101 1-104-913-11 TANTAL. CHIP 10uF 20% 10V
C102 1-115-156-11 CERAMIC CHIP 1uF 10V
C103 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C104 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V

C512 1-104-851-11 TANTAL. CHIP 10uF 20% 10V
C513 1-117-370-11 CERAMIC CHIP 10uF 10V
C710 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C716 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C717 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C718 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V

– 26 –

MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

C719 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C722 1-104-851-91 TANTAL. CHIP 10uF 20% 10V

* C723 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
* C724 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C725 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C730 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V

Q109 8-729-037-76 TRANSISTOR UN9215J-(TX).SO
Q110 8-729-037-76 TRANSISTOR UN9215J-(TX).SO
Q502 8-729-427-74 TRANSISTOR XP4601
Q704 8-729-037-63 TRANSISTOR UN9115J-(TX).SO
Q777 8-729-037-63 TRANSISTOR UN9115J-(TX).SO

<RESISTOR>

<CONNECTOR>

* CN102 1-785-872-21 PLUG, BOARD TO BOARD 10P

CN701 1-785-871-21 CONNECTOR, PC LINK (DIGITAL I/O)

* CN703 1-785-875-21 CONNECTOR, BOARD TO BOARD 50P

<DIODE>

D501 8-719-073-35 DIODE RB551V-30TE-17

<FERRITEBEAD>

FB101 1-414-593-21 FERRITE BEAD INDUCTOR
FB102 1-414-593-21 FERRITE BEAD INDUCTOR
FB103 1-414-593-21 FERRITE BEAD INDUCTOR
FB104 1-414-593-21 FERRITE BEAD INDUCTOR
FB105 1-414-593-21 FERRITE BEAD INDUCTOR

FB106 1-414-593-21 FERRITE BEAD INDUCTOR
FB107 1-414-593-21 FERRITE BEAD INDUCTOR
FB501 1-414-921-11 INDUCTOR 2.2uH
FB503 1-414-921-11 INDUCTOR 2.2uH
FB701 1-414-921-11 INDUCTOR 2.2uH

<IC>

IC101 8-759-567-09 IC MSM7590L-01TS-K
IC102 8-759-567-10 IC XC25A08510MR
IC103 8-759-574-34 IC LMV358MMX
IC104 8-759-701-51 IC NJM2072M
IC105 8-759-582-03 IC NJM2149V-TE2

IC106 8-759-082-60 IC TC7S66FU
IC107 8-759-358-47 IC NJM2115V(TE2)
IC108 8-759-582-03 IC NJM2149V-TE2
IC109 8-759-586-57 IC AN6123MS
IC502 8-759-583-76 IC XC62GR3522MR

IC503 8-759-582-02 IC XC6372C381PR
IC504 8-759-592-24 IC XC61AN1502MR
IC506 8-759-583-76 IC XC62GR3522MR
IC705 8-759-595-14 IC XC61A2202MR
IC707 8-759-592-25 IC CXD9519TQ

IC708 8-759-583-76 IC XC62GR3522MR
IC709 8-759-058-62 IC TC7S08FU(TE85R)
IC710 8-759-333-42 IC XC61AN3002MR
IC777 8-759-710-84 IC NJM2406F-TE2

<COIL>

L501 1-469-395-21 INDUCTOR
L503 1-414-752-11 INDUCTOR 2.2uH

R102 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R103 1-216-815-11 METAL CHIP 330 5% 1/16W
R104 1-216-839-11 METAL CHIP 33K 5% 1/16W
R105 1-216-833-91 RES,CHIP 10K 5% 1/16W
R106 1-216-821-11 METAL CHIP 1K 5% 1/16W

R107 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R108 1-216-821-11 METAL CHIP 1K 5% 1/16W
R109 1-216-841-11 METAL CHIP 47K 5% 1/16W
R110 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R111 1-216-841-11 METAL CHIP 47K 5% 1/16W

R112 1-216-841-11 METAL CHIP 47K 5% 1/16W
R113 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R116 1-216-833-91 RES,CHIP 10K 5% 1/16W
R117 1-216-833-91 RES,CHIP 10K 5% 1/16W
R118 1-216-825-11 METAL CHIP 2.2K 5% 1/16W

R120 1-216-845-11 METAL CHIP 100K 5% 1/16W
R121 1-216-845-11 METAL CHIP 100K 5% 1/16W
R122 1-209-926-11 METAL CHIP 36K 5% 1/16W
R131 1-216-835-11 METAL CHIP 15K 5% 1/16W
R132 1-216-831-11 METAL CHIP 6.8K 5% 1/16W

R133 1-216-833-91 RES,CHIP 10K 5% 1/16W
R134 1-216-841-11 METAL CHIP 47K 5% 1/16W
R135 1-216-841-11 METAL CHIP 47K 5% 1/16W
R136 1-216-837-11 METAL CHIP 22K 5% 1/16W
R137 1-216-849-11 METAL CHIP 220K 5% 1/16W

R138 1-216-833-91 RES,CHIP 10K 5% 1/16W
R139 1-216-839-11 METAL CHIP 33K 5% 1/16W
R140 1-216-845-11 METAL CHIP 100K 5% 1/16W
R141 1-216-837-11 METAL CHIP 22K 5% 1/16W
R142 1-216-853-11 METAL CHIP 470K 5% 1/16W

R143 1-209-926-11 METAL CHIP 36K 5% 1/16W
R144 1-218-292-11 RES,CHIP 20K 5% 1/16W
R145 1-216-833-91 RES,CHIP 10K 5% 1/16W
R146 1-218-292-11 RES,CHIP 20K 5% 1/16W
R147 1-216-817-11 METAL CHIP 470 5% 1/16W

R148 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
R149 1-216-837-11 METAL CHIP 22K 5% 1/16W
R150 1-216-837-11 METAL CHIP 22K 5% 1/16W
R151 1-216-853-11 METAL CHIP 470K 5% 1/16W
R152 1-216-849-11 METAL CHIP 220K 5% 1/16W

R153 1-216-833-91 RES,CHIP 10K 5% 1/16W
R154 1-216-845-11 METAL CHIP 100K 5% 1/16W
R155 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R156 1-216-797-11 METAL CHIP 10 5% 1/16W
R157 1-216-797-11 METAL CHIP 10 5% 1/16W

<TRANSISTOR>

Q101 8-729-429-44 TRANSISTOR XP1501
Q102 8-729-037-63 TRANSISTOR UN9115J-(TX).SO
Q103 8-729-429-50 TRANSISTOR XP4312
Q105 8-729-039-57 TRANSISTOR DTC363EKT146
Q108 8-729-048-59 TRANSISTOR XC161A1265PR

R160 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R161 1-216-821-11 METAL CHIP 1K 5% 1/16W
R162 1-216-799-11 METAL CHIP 15 5% 1/16W
R163 1-216-835-91 RES,CHIP 15K 5% 1/16W
R164 1-216-827-11 METAL CHIP 3.3K 5% 1/16W

R166 1-216-857-11 METAL CHIP 1M 5% 1/16W

– 27 –

ICD-R100PC

MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R167 1-216-833-91 RES,CHIP 10K 5% 1/16W
R171 1-216-813-91 METAL CHIP 220 5% 1/16W
R504 1-216-853-11 METAL CHIP 470K 5% 1/16W
R506 1-216-853-11 METAL CHIP 470K 5% 1/16W

R509 1-216-857-11 METAL CHIP 1M 5% 1/16W
R510 1-216-849-11 METAL CHIP 220K 5% 1/16W
R511 1-218-895-11 RES,CHIP 100K 0.50% 1/16W
R512 1-218-895-11 RES,CHIP 100K 0.50% 1/16W
R514 1-216-845-11 METAL CHIP 100K 5% 1/16W

R515 1-216-864-11 METAL CHIP 0 5% 1/16W
R724 1-216-855-11 METAL CHIP 680K 5% 1/16W
R725 1-216-821-11 METAL CHIP 1K 5% 1/16W
R726 1-216-849-11 METAL CHIP 220K 5% 1/16W
R727 1-216-849-11 METAL CHIP 220K 5% 1/16W

R733 1-216-845-11 METAL CHIP 100K 5% 1/16W
R743 1-216-833-91 RES,CHIP 10K 5% 1/16W
R732 1-216-845-11 METAL CHIP 100K 5% 1/16W
R749 1-216-845-11 METAL CHIP 100K 5% 1/16W
R750 1-216-833-91 RES,CHIP 10K 5% 1/16W

R751 1-216-845-11 METAL CHIP 100K 5% 1/16W
R752 1-216-833-91 RES,CHIP 10K 5% 1/16W
R753 1-216-833-91 RES,CHIP 10K 5% 1/16W
R754 1-216-813-91 METAL CHIP 220 5% 1/16W
R755 1-216-813-91 METAL CHIP 220 5% 1/16W

1-790-857-11 CABLE, CONNECTION
3-866-532-11 MANUAL, INSTRUCTION (ENGLISH) (US)
3-866-532-21 MANUAL, INSTRUCTION (ENGLISH,FRENCH)

3-866-532-31 MANUAL, INSTRUCTION (SPANISH,

3-866-532-41 MANUAL, INSTRUCTION (DANISH,DUTCH)

3-866-532-51 MANUAL, INSTRUCTION (SWEDISH,ITALIAN)

3-866-581-11 MANUAL, INSTRUCTION (ENGLISH) (US)
3-866-581-21 MANUAL, INSTRUCTION (ENGLISH,FRENCH)

3-866-581-31 MANUAL, INSTRUCTION (SPANISH,

3-866-581-41 MANUAL, INSTRUCTION (DANISH,DUTCH)

3-866-581-51 MANUAL, INSTRUCTION (SWEDISH,ITALIAN)

4-217-041-01 CASE, CARRYING
4-220-196-01 FLOPPY (EG), SOFT (No.1)
4-220-196-11 FLOPPY (EG), SOFT (No.2)
4-220-196-21 FLOPPY (EG), SOFT (No.3)

ACCESSORIES&PACKING MATERIALS

*******************************

(Canadian,AEP)

PORTUGUESE) (AEP)

(Canadian,AEP)

PORTUGUESE) (AEP)

(AEP)

(AEP)

(AEP)

(AEP)

R756 1-216-837-11 METAL CHIP 22K 5% 1/16W
R758 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R761 1-216-821-11 METAL CHIP 1K 5% 1/16W
R762 1-216-841-11 METAL CHIP 47K 5% 1/16W
R763 1-216-833-91 RES,CHIP 10K 5% 1/16W

R764 1-216-845-11 METAL CHIP 100K 5% 1/16W
R765 1-216-849-11 METAL CHIP 220K 5% 1/16W

<COMPOSITION CIRCUIT BLOCK >

RB701 1-233-957-11 RES, NETWORK (CHIP TYPE) 220
RB702 1-233-957-11 RES, NETWORK (CHIP TYPE) 220
RB704 1-233-961-21 RES, NETWORK (CHIP TYPE) 1K
RB705 1-233-961-21 RES, NETWORK (CHIP TYPE) 1K

<VARIABLE RESISTOR >

RV101 1-225-502-41 RES, VAR, CARBON 10K/10K(∑ VOL)

<SWITCH>

S101 1-572-922-11 SWITCH, SLIDE (MIC SENS)
S713 1-572-922-11 SWITCH, SLIDE (VOR)
S714 1-692-605-31 SWITCH, SLIDE (PLAY SPEED)

**************************************************************

MISCELLANEOUS

***************

11 1-418-318-11 UNIT, SWITCH
14 1-694-521-11 CONDUCTIVE BOARD, CONECTION
LCD101 1-803-522-11 DISPLAY PANEL, LIQUID CRYSTAL
MIC101 1-542-384-11 MICROPHONE, ELECTRET CONDENSER
SP101 1-505-854-11 SPEAKER (2.8cm)

**************************************************************

Sony Corporation

9-927-123-11

Personal Audio Company

– 28 –

Printed in Japan © 1999.5

99E0266-1

Published by General Engineering Dept.