Sony HTSS360 User Manual

Download

Page 1

Home Theatre System

4-130-033-41(1)

Operating Instructions

HT-SS360

Page 2

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus.

Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus.

As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately.

Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or the like.

The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off.

To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

For customers in the United States, Canada and Mexico

This symbol is intended to alert the user to the presence of the Hot Surface that may be hot if it is touched during the normal operation.

For customers in the United States

Owner’s Record

The model and serial numbers are located on the rear of the unit. Record these numbers in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No.

ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Serial No.

partner, Sony

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electr ician for replacement of the obsolete outlet.

Page 3

10)Protect the power cord from being walked on or pinched particularly at plugs, conveni ence receptacles, and the point where they exit from the apparatus.

11)Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13)Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

The following FCC statement applies only to the version of this model manufactured for sale in the U.S.A. Other versions may not comply with FCC technical regulations.

– Reorient or relocate the receiving antenna. – Increase the separation between the equipment

and receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

To reduce the risk of electric shock, the speaker cord should be connected to the apparatus and the speakers in accordance with the following instructions.

1) Disconnect the AC power cord from the MAINS.

2) Strip 10 to 15 mm of the wire insulation of the speaker cord.

3) Connect the speaker cord to the apparatus and the speakers carefully so as not to touch the core of speaker cord by hand. Also disconnect the AC power cord from the MAINS before disconnecting the speaker cord from the appar atus and the speakers.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Page 4

About This Manual

• The instructions in this manual are for model HT-SS360.

• In this manual, models of area code U is used for illustration purposes unless stated otherwise. Any difference in operation is clearly indicated in the text, for example, “Models of area code CA only”.

The HT-SS360 consists of:

• Receiver STR-KS360

• Speaker system

– Front speaker SS-MSP36S

– Center speaker SS-CNP36

– Surround speaker SS-SRP36S

– Subwoofer SS-WP36

Be sure to use only the supplied speakers.

• The instructions in this manual describe the controls on the supplied remote. You can also use the controls on the receiver if they have the same or similar names as those on the remote.

About area codes

The area code of the receiver you purchased is shown on the lower portion of the rear panel (see the illustration below).

On Copyrights

This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System. * Manufactured under license from Dolby

Laboratories. Dolby, Pro Logic, and the doubleD symbol are trademarks of Dolby Laboratories.

** Manufactured under license under U.S. Patent

#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2008 DTS, Inc. All Rights Reserved.

This receiver incorporates High-Definition Multimedia Interface (HDMI HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

“x.v.Color” and “x.v.Color” logo are trademarks of Sony Corporation.

“BRAVIA” is a trademarks of Sony Corporation.

) technology.

SPEAKERS

FRONT R

FRONT L SUR R SUR L CENTER

Area code

Any differences in operation, according to the area code, are clearly indicated in the text, for example, “Models of area code AA only”.

SUBWOOFER

Page 5

Table of Contents

Description and location of parts .................. 6

Getting Started

1: Installing the speakers ............................. 13

2: Connecting the speakers ......................... 15

3: Connecting the TV .................................. 16

4: Connecting the audio/video

components ............................................ 17

5: Connecting the antennas ......................... 21

6: Preparing the receiver and the remote.....21

7: Calibrating the appropriate settings

automatically

(AUTO CALIBRATION) ...................... 22

8: Adjusting the speaker levels

(TEST TONE)........................................ 26

Playback

Selecting a component ................................ 27

Enjoying sound/images from the

components connected to the receiver ... 28

Amplifier Operations

Navigating through menus .......................... 30

Settings for the HDMI

(SET HDMI menu) ................................ 33

Settings for the Auto Calibration

(A.CAL menu) ....................................... 33

Settings for the Speaker

(SP SETUP menu) ................................. 34

Adjusting the level (LEVEL menu) ............ 35

Adjusting the tone (TONE menu) ............... 35

Settings for the Custom Menu

(CUSTOM menu) .................................. 36

Enjoying Surround Sound

Selecting the sound field ............................. 37

Tuner Operations

Listening to FM/AM radio ..........................38

Presetting radio stations............................... 39

Using “BRAVIA” Sync features

What is “BRAVIA” Sync?...........................41

Preparing for the “BRAVIA” Sync..............42

Playing back components with one-touch

operation (One-Touch Play) ................... 43

Enjoying the TV sound from the speakers

connected to the receiver

(System Audio Control) .........................44

Turning off the receiver with the TV

(System Power Off) ................................ 45

Using the Power Saving function

(Power Save)........................................... 45

Other Operations

Changing the brightness of the display

(DIMMER)............................................. 46

Changing the display setting (DISPLAY) ...47

Using the Sleep Timer (SLEEP).................. 47

Switching between digital and analog

audio (IN MODE) ..................................48

Using the Remote

Changing the input button assignments.......48

Additional Information

Glossary.......................................................49

Precautions ..................................................51

Troubleshooting...........................................52

Specifications ..............................................56

Index ............................................................ 58

Page 6

Description and location of parts

Front panel

?/1

ACTIVE STANDBY

Name Function

A ?/1

(on/standby)

B ACTIVE

STANDBY lamp

C Display The current status of the

D White lamp Lights up when the

E Remote sensor Receives signals from

F MASTER

VOL UM E

G INPUT

SELECTOR

Press to turn the receiver on or off (page 21, 28, 29).

Lights up in amber when the Control for HDMI is set to on and the receiver is on standby mode.

Note

If the ACTIVE STANDBY lamp is flashing, see page 55.

selected component or a list of selectable items appears here (page 7).

receiver is on and DSPL is set to on in DISPLAY function (page 47). Lights off when the receiver is in standby mode or DSPL is set to off in DISPLAY function.

remote commander.

Turn to adjust the volume level of all speakers at the same time (page 27, 28,

29).

Press to select the input source to playback (page 27, 28, 29, 38, 39).

641 73

INPUT SELECTOR

MASTER VOLUME

Page 7

Indicators on the display

2 4 51 3 6

8 79q;qaqs

Name Function

A LFE Lights up when the disc being

B SLEEP Lights up when the sleep timer is

C Playback

channel indicators

L R C SL SR S

D D Lights up when receiver is

E HDMI Lights up when a playback

played back contains an LFE (Low Frequency Effect) channel and the LFE channel signal is actually being reproduced.

activated (page 47).

The letters (L, C, R, etc.) indicate the channels being played back. The boxes around the letters vary to show how the receiver downmixes the source sound. Front Left Front Right Center (monaural) Surround Left Surround Right Surround (monaural or the surround components obtained by Pro Logic processing)

Example:

Recording format (Front/ Surround): 3/2.1 Sound Field: A.F.D. AUTO

SL SR

decoding Dolby Digital signals.

Note

When playing a Dolby Digital format disc, be sure that you have made digital connections.

component is connected to this receiver using an HDMI jack (page 18).

Name Function

F Preset

station

indicators

G Tun er

indicators

H COAX Lights up when the source signal

I OPT Lights up when the source signal

J PL/

PLII

K DTS Lights up when the receiver is

L SW Lights up when the audio signal is

Lights up when using the receiver to tune in radio stations you have preset. For details on presetting radio stations, see page 39.

Lights up when using the receiver to tune in radio stations (page 38), etc.

is a digital signal being input through the COAX IN jack.

is a digital signal being input through the OPT IN jack.

“ PL” lights up when the receiver applies Pro Logic processing to 2 channel signals in order to output the center and surround channel signals. “ PLII” li ghts up when the Pro Logic II Movie/Music decoder is activated.

decoding DTS signals.

Note

When playing a DTS format disc, be sure that you have made digital connections.

output from the SUBWOOFER jack.

Page 8

Rear panel

1 4 5 623

SPEAKERS

FRONT R

FRONT L SUR R SUR L CENTER

SUBWOOFER

A SPEAKERS section

Connects to the supplied speakers and subwoofer (page 15).

B DMPORT

DMPORT jack

Connects to a DIGITAL MEDIA PORT adapter (page

17).

C AUTO CALIBRATION section

AUTO CAL MIC jack

Connects to the supplied optimizer microphone for the Auto Calibration function (page 23).

D AUDIO INPUT section

White (L)

Red (R)

AUDIO IN jacks

Connects to a Super Audio CD player, CD player, etc. (page 17, 20).

AUDIO IN

AUTO

VIDEO 1

CAL MIC

DC5V 700mA MAX

DMPORT

LRL

HDMI

AUDIO IN

SA-CD/CD

BD IN OUTSAT INDVD IN

COAX IN

VIDEO 2

DIGITAL

ANTENNA

OPT IN OPT INAUDIO IN

SAT

E DIGITAL INPUT/OUTPUT section

OPT IN jacks Connects to a DVD

COAX IN jack

HDMI IN/ OUT jacks

player, etc. The COAX IN jack provides a better sound quality (page

20).

Connects to a DVD player, satellite tuner, or a Blu-ray disc player. The image is output to a TV or a projector while the sound can be output from a TV or/and speakers connected to this receiver (page 18).

F ANTENNA section

FM ANTENNA jack

AM ANTENNA terminals

Connects to the supplied FM wire anten na (page 21).

Connects to the supplied AM loop anten na (page 21).

Page 9

Remote commander

You can use the supplied remote RM-AAU057 to operate the receiver and to control the Sony audio/video components that the remote is assigned to operate (page 48).

RM-AAU057

?/1

DMPORT

TV INPUT

VIDEO1 VIDEO2 BD DVD

SAT

BD/DVD

PICTURE

JUMP

123

CLEAR

DISPLAY MUTING

RETURN/EXIT

–

TV CH

REPLAY ADVANCE

PRESET

–

TUNING

–

?/1

SYSTEM STANDBY

SA-CD/CDTV TUNER

F1MENUTOP MENU F2

FAVORITESWIDE

THEATER

GUIDE

AMP MENU

ENTER

TOOLS/ OPTIONS

TV VOL

MASTER VOL

MENU/HOME

TV CH

PRESET

TUNING

?/1

6 7

8 9 q; qa

Basic operations

Remote Button Function

B ?/1

(on/standby)

Press to turn the receiver on or off. To turn off all Sony components, press ?/1 and AV ?/1 (A) at the same time (SYSTEM STANDBY).

Saving the power in standby mode

When “CONTROL FOR HDMI” is set to “CTRL ON” and “P.SAVE” is set to “SAVE ON” (page 33).

C Input buttons Press one of the buttons to

G SOUND FIELD Press to select a sound field. I AMP MENU Press to display the menu of

K MUTING Press to turn off the sound

L MASTER VOL

+*/–

V/v/B/b

select the component you want to use. The buttons are factory assigned to control Sony components. You can change the button assignments following the steps in “Changing the input button assignments” on page

48.

the receiver.

temporarily. Press MUTING again to restore the sound.

Press to adjust the volume.

Press V, v, B or b to select the settings. Then, press to enter the selection.

continued

Page 10

Tuner operations

Common operations

Remote Button Function

H ENTER Press to enter the selection. M MENU/HOME Press to display the menu. N PRESET +/– Press to select a preset

TUNING +/– Press to scan the station.

R DISPLAY Press to display the

S CLEAR Press to clear a mistake

V/v/B/b

station.

Press to select the menu items and to enter the selection.

information during Tuner function.

when you input a wrong character.

DMPORT operations

Remote Button Function

N ./> Press to skip the track.

m/M Press to fast reverse or fast

H (playback)/ X (pause, press

again to resume normal playback/ x (stop)

forward.

Play mode button.

To control the component

1 Press one of the input buttons

C (TV, BD, DVD, or SAT) to select the component you want to operate.

The component assigned to the selected input button becomes operable.

2 Referring to the following table,

press the corresponding button for the operation.

Remote Button Function

A TV ?/1

AV ?/1 (on/standby)

H ENTER Press to enter the selection. T Numeric

buttons (number 5*)

Press to turn on or off the Sony audio/video components that the remote is assigned to operate (page

48). Press A ?/1 and B TV ?/1/AV ?/1 at the same time to turn off the receiver and all other components that the remo te is assigned to operate (SYSTEM STANDBY).

Press to select channels and tracks directly.

To control the TV

Press and hold (O) TV (yellow) button while pressing the buttons with an yellow dot or yellow printing to control the TV.

Remote Button Function

D FAVO RI T ES To display the stor ed favorite

WIDE To select the wide picture

E THEATER Press to sets the optimal

F GUIDE Press to display the guide

J TOOLS/

OPTIONS

channel list of TV.

mode.

picture settings automatically for watching movies, when you connect a Sony TV which is compatible with the THEATER button. Also, th e audio is automatically switched to the audio output of this receiver when you connect the TV and the receiver with HDMI connection, and the Control for HDMI function is set to on.

when you are watching analog and digital channels.

Press to enable you to access various viewing options and change/make adjustments according to the source and screen format.

Page 11

Remote Button Function

K MUTING Press to turn off the sound. L TV +/– Press to adjust the volume. M MENU/HOME Press to allow you to select

N TV CH +/– Selects the next (+) or

P RETURN/

EXIT

V/v/B/b

R DISPLAY Display the TV’s

S Selects digital channels

T Numeric

buttons (number 5*)

U JUMP Press to select the previous

PICTURE Press to cycle through the

V TV INPUT Press to select input.

channels or input sources and change the settings for your TV.

previous (–) channel. To scan quickly through channels, press and hold down either +/–.

Press to return to the previous screen of any displayed menu.

Press to sele ct the men u item and enters the selection.

information on the TV screen. (Displays the current channel number, etc.)

using with the 0-9 and ENTER buttons. For example, to enter “2.1”, press , , and

2 1

ENTER.

Press to select channels. Press ENTER (H) to change channels immediately.

and the current channels of the TV, Satellite tuner, Bluray disc recorder, DVD player.

available picture modes of the TV.

To control the DVD recorder/Blu-ray Disc recorder

Remote Button Function

D F1 Press to select the HDD.

F2 Press to select the Blu-ray

M MENU/HOME Press to display the menu. N . Press to skip chapters.

> Press to skip forward to the

m/M Press to fast reverse or to fast

H* (playback)/ X (pause, press

again to resume normal playback/ x (stop)

V/v/B/b

U BD/DVD

TOP MENU, MENU

Disc/DVD.

Press to jump backward while viewing live or recorded programs.

Press to jump forward while viewing recorded programs.

next available chapter.

forward the disc when pressed during playback.

Play mode button.

Press to select a menu item and enters the selection.

Press to display the top menu or disc menu.

continued

Page 12

To control the DVD player/ Blu-ray Disc player

Remote Button Function

M MENU/HOME Press to display the menu. N ./> Press to skip chapters.

REPLAY Press to jump backward.

ADVANCE Press to jump forward.

m/M Press to fast reverse or to fast

forward the disc when pressed during playback.

H* (playback)/

Play mode button.

X (pause, press again to resume normal playback/ x (stop)

V/v/B/b

U BD/DVD

TOP MENU,

Press to select a menu item and enters the selection.

Press to display the top menu or disc menu.

To control the HDD/DVD COMBO

Remote Button Function

D F1 Press to select the HDD.

F2 Press to select the DVD.

M MENU/HOME Press to display the menu. N ./> Press to specify the

m/M Press to fast reverse or to fast

H* (playback)/ X (pause, press

again to resume normal playback/ x (stop)

V/v/B/b

U BD/DVD

TOP MENU, MENU

previous/next chapter/track.

Press to change to replay mode.

Press to advance.

forward the disc when pressed during playback.

Play mode button.

Press to move the highlight (cursor) and selects the item.

Press to display the top menu or disc menu.

To control the SAT

Remote Button Function

F GUIDE Press to display the guide

M MENU/HOME Press to display the menu. Q

V/v/B/b

* The nu mbe r 5, MA STER VOL + and H buttons

have tactile dots. Use the tactile dots as references

when operating the receiver.

menu.

Press to select a menu item and enters the selection.

Notes

• Some functions explained in this section may not work depending on the model.

• The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.

Page 13

Getting Started

Installing the speakers on a flat surface

Getting Started

1: Installing the speakers

This receiver allows you to use a 5.1 channel speaker system. To fully enjoy theater-like multi channel surround sound, be sure to connect all the speakers (two front speakers, a center speaker, and two surround speakers) and a subwoofer (5.1 channel). You can place your speakers as shown below.

AFront speaker (left) BFront speaker (right) CCenter speaker DSurround speaker (left) ESurround speaker (right) FSubwoofer

Before you install the speaker and subwoofer, be sure to attach the supplied foot pads to prevent vibration or movement as shown in the illustration below.

Example of front speaker

Installing the speakers on the speaker stand

For greater flexibility in positioning the speakers, use the optional WS-FV11 or WS-FV10D speaker stand (available only in certain countries). For details, refer to the operating instructions supplied with the speaker stand.

Tip

Since the subwoofer does not emit highly directional signals, you can place it wherever you want.

Page 14

Installing the speakers on the wall

3 Hang the speakers on the

screws.

You can install your speakers on the wall.

1 Prepare screws (not supplied)

that are suitable for the hook on the back of each speaker. See the illustrations below.

4 mm (3/16 inch)

more than 25 mm (more than 1 inch)

4.6 mm (3/16 inch)

10 mm (13/32 inch)

Hook on the back of the speaker

2 Fasten the screws to the wall.

The screws should protrude 7/32 to 9/32 inch.

For the center speaker

160 mm (6 5/16 inches)

4.6 mm (3/16 inch)

10 mm (13/32 inch)

Rear of speaker

Notes

• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where reinforcement is applied.

• Contact a screw shop or installer regarding the wall material or screws to be used.

• Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or improper screw installation, natural calamity, etc.

5 mm to 7 mm

(7/32 to 9/32 inch)

For the front speakers and surround speakers

5 mm to 7 mm

(7/32 to 9/32 inch)

Page 15

2: Connecting the speakers

Before connecting the cords, be sure to disconnect the AC power cord (mains lead).

Connector

SPEAKERS

CENTER

FRONT L SUR R SUR LFRONT R

SUBWOOFER

Note on speaker cords

The connector of the speaker cords are the same color as the speaker jack to be connected. When connecting a speaker cord, be sure to match the colored connector to the speaker jack on the receiver:

Connector Speaker jack

Red FRONT R

White FRONT L

Grey SUR R

Blue SUR L

Green CENTER

Purple SUBWOOFER

To connect the speakers correctly

Check the speaker type by referring to the speaker label* at the rear panel of the speakers.

Character on speaker label

L Front left

R Front right

SL Surround left

SR Surround right

* The center speaker and subwoofer do not have the

character on the speaker label. For details on the speaker type, see page 4.

Speaker type

Getting Started

A Speaker cord (supplied)

AFront speaker (left) BFront speaker (right) CCenter speaker DSurround speaker (left) ESurround speaker (right) FSubwoofer

Page 16

3: Connecting the TV

You can watch the selected input image when you connect the HDMI OUT jack to a TV. It is not necessary to connect all the cords. Connect audio and video cords according to the jacks of your components. Before connecting the cords, be sure to disconnect the AC power cord.

Tips

• To output the sound of the TV from the speakers connected to the receiver, be sure to

– connect the audio output jacks of the TV to the

TV IN jacks of the receiver.

– turn off the TV’s volume or activate the TV’s

muting function.

• All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling frequencies.

AUDIO IN

VIDEO 1

mA MAX

HDMI

Audio signal

AUDIO IN

COAX IN

VIDEO 2

SA-CD/CD

BD IN OUTSAT INDVD IN

DIGITAL

OPT IN OPT INAUDIO IN

SAT

Audio/video

signal

ANTENNA

A Audio cord (not supplied) B Optical digital cord (not supplied) C HDMI cable (not supplied)

We recommend that you use a Sony HDMI cable.

Notes

• Be sure to turn on the receiver when the video and audio signals of a playback component are being output to a TV via the receiver. Unless the power is turned on, neither video no r audio signals will be transmitted.

• When connecting optical digital cords, insert the plugs straight in until they click into place.

• Do not bend or tie optical digital cords.

Page 17

4: Connecting the audio/

video components

How to hook up your components

This section describes how to hook up your components to this receiver. Before you begin, refer to “Component to be connected” below for the pages which describe how to connect the audio/video components. Before connecting the cords, be sure to disconnect the AC power cord (mains lead). After hooking up all your components, proceed to “5: Connecting the antennas” (page

21).

Component to be connected

To connect See

TV page 16

Audio components

• Super Audio CD player/ CD player

• DIGITAL MEDIA PORT adapter

Components with HDMI jack page 18

Video components

• Satellite tuner, Set-top box

• DVD player, DVD recorder

•VCR

page 17

page 20

Connecting audio components

The following illustration shows how to connect audio components such as Super Audio CD player or CD player and DIGITAL MEDIA PORT adapter. You can also view the images on the TV screen by connecting the video output of the DIGITAL MEDIA PORT adapter to the video input of the TV.

Super Audio CD player,

CD player

Audio signal

AUDIO IN

AUTO

VIDEO 1

CAL MIC

DC5V 700mA MAX

DMPORT

LRL

HDMI

AUDIO IN

COAX IN

VIDEO 2

SA-CD/CD

BD IN SAT INDVD IN

DIGITAL

OPT IN OPT INAUDIO IN

SAT

Getting Started

DIGITAL

MEDIA PORT

adapter

A Audio cord (not supplied) B Video cord (not supplied)

* The type of connector varies depending on the

DIGITAL MEDIA PORT adapter. For details, refer to the operating instructions supplied with the DIGITAL MEDIA PORT adapter.

continued

Page 18

Notes on connecting DIGITAL MEDIA PORT adapter

• Do not connect or disconnect the DIGITAL MEDIA PORT adapter while the receiver is turned on.

• Be sure to make DMPORT connections firmly, insert the connector straight in.

• As the connector of the DIGITAL MEDIA PORT adapter is fragile, be sure to handle with care when placing or moving the receiver.

• When connecting the DIGITAL MEDIA PORT adapter, be sure the connector is inserted with the arrow mark facing toward the arrow mark on the DMPORT jack. To detach the DIGITAL MEDIA PORT adapter, press and holed both sided of the connector and then pull out the connector.

Connecting components with HDMI jacks

HDMI is the abbreviated name for HighDefinition Multimedia Interface. It is an interface which transmits video and audio signals in digital format. Sony recommends that you connect components to the receiver using an HDMI cable. With HDMI, you can easily enjoy both high quality sound and high quality images.

However, it is necessary to connect the audio output of the TV to the audio input of the receiver using an optical cord to listen to the TV multi channel surround sound broadcasting from the receiver.

By connecting Sony “BRAVIA” Sync compatible components using HDMI cables, ““BRAVIA” Sync Features” makes operations simpler (page 41).

HDMI features

• A digital audio signals transmitted by HDMI can be output from the speakers connected to the receiver. This signal supports Dolby Digital, DTS and Linear PCM.

• This receiver supports xvYCC transmission.

• This receiver supports the Control for HDMI function. For details, see “Using “BRAVIA” Sync features” (page 41).

Page 19

TV, etc.

Audio signals

Audio/video

signals

Notes on HDMI connections

• An audio signal input to the HDMI IN jack is output from the SPEAKERS jacks and HDMI OUT jack. It is not output from any

Getting Started

other audio jacks.

• Video signals input to the HDMI IN jack can only be output from the HDMI OUT jack.

ABC

• The multi/stereo area audio signals of a Super Audio CD are not output.

• Audio signals (sampling frequency, bit length, etc.) transmitted from an HDMI jack may be suppressed by the connected component. Check the setup of the connected component if the image is poor or the sound does not come out of a component connected via the HDMI cable.

• Sound may be interrupted when the sampling frequency, the number of channels or the audio format of the audio output

AUDIO IN

VIDEO 1

mA MAX

HDMI

DIGITAL

AUDIO IN

COAX IN

OPT INAUDIO IN

SAT

VIDEO 2

SA-CD/CD

BD IN OUT

SAT INDVD IN

OPT IN

ANTENNA

signals from the playback component is switched.

AAA

• When the connected component is not compatible with copyright protection technology (HDCP), the image and/or the sound from the HDMI OUT jack may be distorted or may not be output.

Audio/video

signals

Blu-ray disc

player

Audio/video

signals

DVD recorder/

DVD player

Audio/video

signals

Satellite tuner/

Set-top box

In this case, check the specification of the connected component.

• You can enjoy multi channel Linear PCM only with an HDMI connection.

• Set the image resolution of the playback

A HDMI cable (not supplied)

We recommend that you use a Sony HDMI cable.

B Optical digital cord (not supplied) C Audio cord (not supplied)

If you connect a DVD player, be sure to change the

factory setting of the DVD button on the remote so that you can use the button to control your DVD player. For details, see “Changing the input button assignments” (page 48).

Connect at least one of the audio cords (B or C).

component to 720p, 1080i or 1080p when you output 96 kHz multi channel sound over an HDMI connection.

• You may need to make certain settings on the image resolution of the player before you can enjoy multi channel Linear PCM. Refer to the operating instructions of the player.

• Refer to the operating instructions of each component connected for details.

• We do not recommend using an HDMI-DVI conversion cable. When you connect an HDMI-DVI conversion cable to a DVI-D component, the sound and/or the image may not be output.

Page 20

Connecting video components

The following illustration shows how to connect video components such as DVD player, DVD recorder, VCR, etc. It is not necessary to connect all the cords. Connect audio and video cords according to the jacks of your components.

DVD re co rd er,

DVD player

Audio signals

Satellite tuner,

Set-top box

Audio signals

DIGITAL

ANTENNA

Notes

• To input multi channel digital audio from the DVD player, set the digital audio output setting on the DVD player. Refer to the operating instructions supplied with the DVD player.

• When connecting optical digital cords, insert the plugs straight in until they click into place.

• Do not bend or tie optical digital cords.

• Be sure to connect the video output of the DVD player, DVD recorder and VCR to the TV, so that the image is displayed on the TV. Refer to the operating instructions of each connected component for details.

• You cannot do recording on the DVD recorder or VCR via this receiver. For details, refer to the operating instructions supplied with the DVD recorder or VCR.

Tip

All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling frequencies.

AUDIO IN

AUTO

VIDEO 1

CAL MIC

DC5V 700mA MAX

DMPORT

AUDIO IN

HDMI

AUDIO IN

COAX IN

VIDEO 2

SA-CD/CD

BD IN OUTSAT INDVD IN

OPT IN

SAT

OPT IN

Audio signal

VCR

A Audio cord (not supplied) B Coaxial digital cord (not supplied) C Optical digital cord (not supplied)

Page 21

5: Connecting the

antennas

Connect the supplied AM loop antenna and FM wire antenna. Before connecting the antennas, be sure to disconnect the AC power cord (mains lead).

FM wire antenna (supplied)

AM loop antenna (supplied)

6: Preparing the receiver and the remote

Connecting the AC power cord (mains lead)

Connect the AC power cord (mains lead) to a wall outlet.

AC power cord (mains lead)

Getting Started

AUDIO IN

VIDEO 1

mA MAX

LRL

HDMI

AUDIO IN

COAX IN

VIDEO 2

SA-CD/CD

BD IN OUTSAT INDVD IN

DIGITAL

ANTENNA

OPT IN OPT INAUDIO IN

SAT

* The shape of the connector varies depending on

the area code of this receiver.

Notes

• To prevent noise pickup, keep the AM loop antenna away from the receiver and other components.

• Be sure to fully extend the FM wire antenna.

• After connecting the FM wire antenna, keep it as horizontal as possible.

SPEAKERS

FRONT R

FRONT L SUR R SUR L CENTER

To the wall outlet

Performing initial setup operations

Before using the receiver for the first time, initialize the receiver by performing the following procedure. This procedure can also be used to return settings you have made to their factory defaults. Be sure to use the buttons on the receiver for this operation.

1,2

?/1

ACTIVE STANDBY

INPUT SELECTOR

MASTER VOLUME

1 Press ?/1 to turn on the

receiver.

2 Hold down ?/1 for 5 seconds.

“CLEARED” appears. All the settings you have changed or adjusted are reset to the initial settings.

Page 22

Inserting batteries into the remote

Insert two R6 (size-AA) batteries in the RM-AAU057 Remote Commander. Observe the correct polarity when installing batteries.

Notes

• Do not leave the remote in an extremely hot or

humid place.

• Do not use a new battery with old ones.

• Do not mix manganese batteries and other kinds of

batteries.

• Do not expose the remote sensor to direct sunlight

or lighting apparatuses. Doing so may cause a malfunction.

• If you do not intend to use the remote for an

extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.

• When you replace the batteries, the remote buttons

may be reset to their factory settings. If this happens, reassign the buttons again (page 48).

• When the remote no longer operates the receiver,

replace all the batteries with new ones.

7: Calibrating the appropriate settings automatically

(AUTO CALIBRATION)

This receiver is equipped with DCAC (Digital Cinema Auto Calibration) Technology which allows you to perform automatic calibration as follows:

• Check the connection between each speaker and the receiver.

• Adjust the speaker level.

• Measure the distance of each speaker from your listening position.

• Measure the frequency characteristics.*

* The measurement result is not utilized for signals

with a sampling frequency of more than 96 kHz.

The DCAC is designed to obtain proper sound balance in your room. However, you can adjust the speaker levels manually according to your preference. For details, see “8: Adjusting the speaker levels (TEST TONE)” (page 26).

Page 23

Before you perform Auto Calibration

Before you perform the Auto Calibration, set up and connect the speakers (page 13, 15).

• The AUTO CAL MIC jack is used for the supplied optimizer microphone only. Do not connect other microphones to this jack. Doing so may damage the receiver and the microphone.

• During the calibration, the sound that comes out of the speakers is very loud. The volume of the sound cannot be adjusted. Pay attention to the presence of children or to the effect on your neighborhood.

• Perform the Auto Calibration in a quiet environment to avoid the effect of noise and to get a more accurate measurement.

• If there are any obstacles in the path between the optimizer microphone and the speakers, the calibration cannot be performed correctly. Remove any obstacles from the measurement area to avoid measurement error.

Note

If the muting function has been activated before you perform Auto Calibration, the muting function will be set to off automatically.

Optimizer

ANTENNA

DIGITAL

OPT IN OPT INAUDIO IN

microphone

SAT

FRONT R

SPEAKERS

FRONT L SUR R SUR L CENTER

LRL

AUDIO IN

COAX IN

AUTO

VIDEO 2

VIDEO 1

SA-CD/CD

CAL MIC

DC5V 700mA MAX

HDMI

SUBWOOFER

BD IN OUTSAT INDVD IN

DMPORT

1 Connect the supplied optimizer

microphone to the AUTO CAL MIC jack.

2 Set up the optimizer

microphone.

Place the optimizer microphone at your listening position.You can also use a stool or tripod so that the optimizer microphone remains at the same height as your ears.

Tip

When you face the speaker towards the optimizer microphone, you will get a more accurate measurement.

Performing Auto Calibration

?/1

SYSTEM STANDBY

SA-CD/CDTV TUNER

F1MENUTOP MENU F2

FAVORITESWIDE

THEATER

GUIDE

SOUND

FIELD

AMP MENU

ENTER

TOOLS/ OPTIONS

TV VOL

MASTER VOL

MENU/HOME

?/1 swi tch

Input buttons

AMP MENU

MUTING

MASTER VOL +/–

,V,v,B,b

DMPORT

TV INPUT

VIDEO1 VIDEO2 BD DVD

SAT

BD/DVD

JUMP

PICTURE

123

CLEAR

DISPLAY MUTING

RETURN/EXIT

Getting Started

1 Press AMP MENU. 2 Press V/v repeatedly to select

“A.CAL”.

3 Press or b to enter the

menu.

“START” appears on the display.

continued

Page 24

4 Press to start the

measurement.

Measurement starts in 5 seconds. While the time is counting down, stand away from the measurement area to avoid measurement error. The measurement process will take approximately 30 seconds to complete.

The table below shows the display when measurement starts.

Measurement for Display

Speaker existance TONE

Speaker gain, distance, frequency response

Subwoofer gain and distance WOOFER

Note

If “CHK MIC” appears, you cannot perform the Auto Calibration. Connect the calibration mic, then restart the Auto Calibration.

Tips

• When Auto Calibration starts: – Stand some distance from the speakers and the

listening position to avoid measurement failure. This is because test signals are output from the speakers during measurement.

– Avoid making noise to get a more accurate

measurement.

• The Auto Calibration function will be canceled

when you do the following during the measurement process:

– Press ?/1 or MUTING. – Press input buttons on the remote or INPUT

SELECTOR on the receiver.

– Change the volume level.

T.S.P.

Confirming/saving the measurement results

1 Confirm the measurement

result.

When the measurement ends, a beep sounds and the measurement result appears on the display.

Measurement result

When the measurement process completes properly

When the measurement process fails

Display Explanation

SAVE Proceed to step

ERROR

XXXX

See “When error codes appear” (page

25).

2 Press V/v repeatedly to select

the item. Then, press .

Item Explanation

SAVE Saves the measurement

WRN CHK Displays warning

DIST Displays the measurement

LEVEL Displays the measurement

EXIT Exits the setting process

results and exits the setting process.

concerning the measurement results. See “When you select “WRN CHK”” (page 25).

result for speaker distance.

result for speaker level.

without saving the measurement results.

Note

After “SAVE” is displayed for 50 seconds, the measurement result is saved automatically, without the need to save the procedure.

3 Save the measurement result.

Select “SAVE” in step 2. The measurement results are saved.

Page 25

When error codes appear

Try the remedies and perform the Auto Calibration again.

Error code Cause and remedies

ERROR 32 • The sound input from the

optimizer microphone is out of the acceptable range.

• The optimizer microphone or subwoofer may be damaged.

Contact your Sony dealer or local authorized Sony service facility.

ERROR F 33 The front speakers are not

connected. Check that the front speakers are connected properly.

ERROR SR 33 Either the surround left or

surround right speaker is not connected. Check that the surround speakers are connected properly.

ERROR SW 33 The subwoofer may be damaged.

Contact your Sony dealer or local authorized Sony service facility.

Warning code Explanation

WARN 43 The distance and position of a

subwoofer cannot be detected. This may be caused by noise. Try to perform the Auto Calibration in a quiet environment.

NO WARN There is no warning information.

When you select “DIST” or “LEVEL”

You can check the speaker distance or speaker level.

When you have finished

Disconnect the optimizer microphone from the receiver.

Note

If you have changed the position of the speakers, it is recommended that you perform Auto Calibration again in order to enjoy the surround sound.

Getting Started

When you select “WRN CHK”

If a warning on the measurement result is present, detailed information is displayed.

Press or B to return to step 2 of “Confirming/saving the measurement results”.

Warning code Explanation

WARN 40 The Auto Calibration has

WARN 41 WARN 42

completed. However, the noise level is high. You may be able to perform the Auto Calibration properly if you try it again, even though the measurement cannot be performed in all environments. Try to perform the Auto Calibration in a quiet environment.

The sound input from the optimizer microphone is out of the acceptable range. The distance between the optimizer microphone and the speakers is too closed. Set them away, and then try to perform the Auto Calibration.

Clearing the measurement result

You can delete the result of Auto Calibration. If there is no saved data, you cannot delete the result.

1 Press AMP MENU. 2 Press V/v repeatedly until

“A.CAL” appears, then press

or b.

3 Press V/v repeatedly to select

“A.CAL CLR”, then press or b.

4 Press V/v repeatedly to select

“YES”, then press .

The saved result is deleted. The settings for speaker distance and speaker level return to their defaults.

Page 26

8: Adjusting the speaker levels

(TEST TONE)

You can adjust the speaker levels while listening to the test tone from your listening position.

AMP MENU

MASTER VOL +/–

,V,v,B,b

AMP MENU

CLEAR

DISPLAY MUTING

RETURN/EXIT

ENTER

TOOLS/ OPTIONS

MASTER VOL

MENU/HOME

TV VOL

1 Press AMP MENU.

“SET HDMI” appears on the display.

• FR LVL: adjusts the front right speaker level.

• SR LVL: adjusts the surround right speaker level.

• SL LVL: adjusts the surround left speaker level.

• SW LVL: adjusts the subwoofer level.

Notes

• “CNT LVL” does not appear when you set

“CNT N” in the “SP SETUP” setting.

• “SR LVL” and “SL LVL” do not appear when

you set “SUR N” in the “SP SETUP” setting.

6 Press V/v to adjust the speaker

level, then press or b.

You can adjust from –6.0 dB to +6.0 dB in 0.5 dB steps.

Note

If you do not adjust for a certain period, the test tone is emitted from the next speaker in sequence.

2 Press V/v repeatedly until

“LEVEL” appears, then press

or b.

3 Press V/v repeatedly until

“T. TONE” appears, then press

or b.

4 Press V/v repeatedly to select

“T. TONE Y”, then press .

The test tone is output from each speaker in sequence as follows: Front left t Center t Front right t Surround right t Surround left t Subwoofer

5 Press V/v repeatedly to select

the desired speaker, then press

or b.

The test tone is emitted from the speaker that is being adjusted only.

• FL LVL: adjusts the front left speaker level.

• CNT LVL: adjusts the center speaker level.

7 Repeat step 5 and 6 to adjust

the speaker level.

8 After you have finished making

adjustments, press V/v until “T. TONE” appears, then press

or b.

9 Press V/v repeatedly to select

“T. TONE N,” then press .

10Press AMP MENU.

The AMP menu turns off.

When a test tone is not output from the speakers

• The speaker cords may not be connected securely.

• The speaker cords may have the short-circuit problem.

• The test tone signals are not output from the HDMI OUT jack.

Page 27

Playback

Selecting a component

?/1

DMPORT

TV INPUT

VIDEO1 VIDEO2 BD DVD

SAT

BD/DVD

PICTURE

JUMP

123

CLEAR

DISPLAY MUTING

RETURN/EXIT

Press the input button to select

a component.

You can also use INPUT SELECTOR on the receiver. The selected input appears on the display.

?/1

SYSTEM STANDBY

SA-CD/CDTV TUNER

F1MENUTOP MENU F2

FAVORITESWIDE

THEATER

GUIDE

SOUND

FIELD

AMP MENU

ENTER

TOOLS/ OPTIONS

TV VOL

MASTER VOL

MENU/HOME

Input buttons

MUTING

MASTER VOL +/–

Selected input [Display]

DMPORT [DMPORT]

Components that can be played back

DIGITAL MEDIA PORT adapter connected to the DMPORT jack

VIDEO1 or VIDEO2 [VIDEO 1 or

VCR, etc., connected to the VIDEO 1 or VIDEO 2 jack

VIDEO 2]

BD [BD]

DVD [DVD]

Blu-ray disc player, etc., connected to the BD jack

DVD player, DVD recorder, etc., connected to the DVD jack

SAT [SAT]

Satellite tuner, set-top box, etc., connected to the SAT jack

TV [TV]

SA-CD/CD [SA-CD/CD]

TV, etc., connected to the TV jack

Super Audio CD/CD player, etc., connected to the SA-CD/CD jack

TUNER

Built-in radio tuner

[FM or AM band]

2 Turn on the component and

start playback.

3 Press MASTER VOL +/– to

adjust the volume.

You can also use MASTER VOLUME on the receiver.

Playback

To activate the muting function

Press MUTING. The muting function will be canceled when you do the following.

• Press MUTING again.

• Increase the volume.

• Turn off the receiver.

To avoid damaging your speakers

Before you turn off the receiver, be sure to turn down the volume level.

Page 28

Enjoying sound/images from the components connected to the receiver

?/1

SYSTEM STANDBY

SA-CD/CDTV TUNER

F1MENUTOP MENU F2

FAVORITESWIDE

THEATER

SOUND

AMP MENU

ENTER

TOOLS/ OPTIONS

MASTER VOL

MENU/HOME

TV CH

PRESET

TUNING

?/1

GUIDE

FIELD

TV VOL

?/1

SOUND FIELD

MASTER VOL +/–

DMPORT

TV INPUT

Input

buttons

VIDEO1 VIDEO2 BD DVD

SAT

JUMP

123

CLEAR

DISPLAY MUTING

RETURN/EXIT

TV CH

PRESET

TUNING

BD/DVD

PICTURE

–

REPLAY ADVANCE

–

Enjoying TV

Turn on the TV and choose a

program.

For details, refer to the operating instructions of the TV.

Tips

• When you connect a Sony TV, the audio input of

the TV is switched and the image from the TV tuner is displayed on the TV screen automatically by pressing the TV button. To change this setting, see “Changing the input button assignments” (page

48).

• The sound may be output from the TV’s speaker.

In this case, turn the volume of the TV’s speaker down to the minimum.

Enjoying a satellite tuner

1 Turn on the TV.

For details, refer to the operating instructions of the TV.

2 Turn the satellite tuner and the

receiver on.

3 Press SAT.

You can also use INPUT SELECTOR on the receiver to select “SAT”.

4 Change the TV input.

For details, refer to the operating instructions of the TV.

5 Adjust the volume of the

receiver.

Tip

The sound may be output from the TV’s speaker. In this case, turn the volume of the TV’s speaker down to the minimum.

2 Turn the receiver on. 3 Press TV. 4 Adjust the volume of the

receiver.

Page 29

Enjoying Blu-ray Disc or DVD Enjoying a VCR

1 Turn on the TV. 2 Turn the Blu-ray Disc or DVD

player (recorder) and the receiver on.

3 Press DVD or BD.

You can also use INPUT SELECTOR on the receiver to select “DVD” or “BD”. Be sure to change the factory setting of the DVD input button on the remote so that you can use the button to control your DVD player. For details, see “Changing the input button assignments” (page 48).

4 Change the TV input.

For details, refer to the operating instructions of the TV.

5 Play back the disc. 6 Adjust the volume.

Tip

Even if you playback Dolby True HD, Dolby Digital Plus or DTS-HD with a connected component compatible with these sound formats, the receiver accepts as Dolby Digital or DTS. When you connect the component to the receiver using an HDMI cable to playback these high-quality sound formats, set the connected component to output the sound in multi channel PCM, if possible.

1 Turn on the TV. 2 Turn the VCR player and the

receiver on.

3 Press VIDEO1 or VIDEO2.

You can also use INPUT SELECTOR on the receiver to select “VIDEO 1” or “VIDEO 2”.

4 Change the TV input.

For details, refer to the operating instructions of the TV.

5 Play back the tape on the VCR.

Enjoying a Super Audio CD/CD

1 Turn on the Super Audio CD

player/CD player, then place the disc on the tray.

2 Turn on the receiver. 3 Press SA-CD/CD.

You can also use INPUT SELECTOR on the receiver to select “SA-CD/CD”.

4 Adjust the volume.

Playback

Page 30

Amplifier Operations

To return to the previous display

Press B.

Navigating through menus

By using the amplifier menus, you can make various adjustments to customize the receiver.

AMP MENU

ENTER

TOOLS/ OPTIONS

MASTER VOL

MENU/HOME

GUIDE

SOUND

FIELD

TV VOL

TV CH

PRESET

TUNING

AMP MENU

V,v,B,b

CLEAR

DISPLAY MUTING

RETURN/EXIT

TV CH

–

REPLAY ADVANCE

PRESET

–

TUNING

–

1 Press AMP MENU.

“SET HDMI” appears on the display.

2 Press V/v repeatedly to select

the menu you want.

3 Press or b to enter the

menu.

To exit the menu

Press AMP MENU.

4 Press V/v repeatedly to select

the parameter you want to adjust.

5 Press or b to enter the

parameter.

6 Press V/v repeatedly to select

the setting you want.

7 Press or b to enter the

setting.

Page 31

Overview of the menus

The following options are available in each menu. For details on navigating through menus, see page 30.

Menu [Display]

HDMI settings [SET HDMI] (page 33)

Auto Calibration settings [A.CAL] (page 33)

Speaker settings [SP SETUP] (page 34)

Parameters [Display]

Control for HDMI

a)b)

[CONTROL FOR HDMI]

Volume limits

[VOL LIM]

Power save

[P.SAVE]

Auto calibration start

[START]

Clear Auto Calibration result [A.CAL CLR]

Center speaker

[CNT SP]

Surround speakers [SUR SP]

Front left speaker distance [FL DIST]

Center speaker distance

a)e)

[CNT DIST]

Front right speaker distance [FR DIST]

Surround right speaker

a)e)

distance [SR DIST]

Surround left speaker

a)e)

distance [SL DIST]

Subwoofer distance

a)e)

[SW DIST]

Settings Initial setting

CTRL ON, CTRL OFF CTRL OFF

MAX, 39……1, MIN MAX

SAVE ON, SAVE OFF SAVE ON

For details, see “Performing Auto Calibration” (page 23).

a)d)

YES, NO NO

CNT Y, CNT N CNT Y

SUR Y, SUR N SUR Y

a)e)

FL 0.00 m to FL 7.00 m (FL 0.00 ft. to FL 23.00 ft.) (0.10 m (0.25 ft.) step)

CNT 0.00 m to CNT 7.00 m (CNT 0.00 ft. to CNT 23.00 ft.) (0.10 m (0.25 ft.) step)

a)e)

FR 0.00 m to FR 7.00 m (FR 0.00 ft. to FR 23.00 ft.) (0.10 m (0.25 ft.) step)

SR 0.00 m to SR 7.00 m (SR 0.00 ft. to SR 23.00 ft.) (0.10 m (0.25 ft.) step)

SL 0.00 m to SL 7.00 m (SL 0.00 ft. to SL 23.00 ft.) (0.10 m (0.25 ft.) step)

(SW 0.00 m to SW 7.00 m) (SW 0.00 ft. to SW 23.00 ft.) (0.10 m (0.25 ft.) step)

Amplifier Operations

FL 3.00 m (FL 10.00 ft.)

CNT 3.00 m (CNT 10.00 ft.)

FR 3.00 m (FR 10.00 ft.)

SR 3.00 m (SR 10.00 ft.)

SL 3.00 m (SL 10.00 ft.)

SW 3.00 m (SW 10.00 ft.)

continued

Page 32

Menu [Display]

Level settings [LEVEL] (page 35)

Tone settings [TONE] (page 35)

Custom settings [CUSTOM] (page 36)

Parameters [Display]

Test tone [T. TONE]

Front left speaker level

[FL LVL]

Center speaker level [CNT LVL]

Front right speaker level [FR LVL]

Surround right speaker level [SR LVL]

Surround left speaker level [SL LVL]

Subwoofer level [SW LVL]

Bass level [BASS]

Treble level [TREBLE]

Digital broadcast language

selection [DUAL]

Synchronizes audi o with video output

Settings Initial setting

T. TONE N, T. TONE Y T. TONE N

FL –6 dB to FL +6 dB (0.5 dB step)

CNT –6 dB to CNT +6 dB (0.5 dB step)

FR –6 dB to FR +6 dB (0.5 dB step)

SR –6 dB to SR +6 dB (0.5 dB step)

SL –6 dB to SL +6 dB (0.5 dB step)

SW –6 dB to SW +6 dB (0.5 dB step)

BASS –6 dB to BASS +6 dB (0.5 dB step)

TRE –6 dB to TRE +6 dB (0.5 dB step)

MAIN, SUB, MAIN/SUB MAIN

SYNC OFF, SYNC 1 to SYNC 20 SYNC OFF

[A/V SYNC]

Audio Dynamics range compression

DRC OFF, DRC STD, DRC MAX DRC OFF

[AUD. DRC]

Brightness of the display

DIMMER Y, DIMMER N DIMMER N

[DIMMER]

Display

DSPL ON, DSPL OFF DSPL ON

[DISPLAY]

Sleep timer [SLEEP]

Switching the audio input

a)f)

mode

SLP OFF, SLP 10M, SLP 20M…. SLP 90M

AUTO, OPT AUTO

[IN MODE]

For details, refer to the page in the parentheses.

“CONTROL FOR HDMI” scroll across the display, then “CONTROL” appears.

The initial setting for the model of MX area code is “CTRL ON”.

This parameter is only available when the result of the Auto Calibration is saved.

When the Auto Calibration result is saved, you can adjust the setting in 0.01 meter increment.

This parameter is only available when SAT input is selected.

FL 0.0 dB

CNT 0.0 dB

FR 0.0 dB

SR 0.0 dB

SL 0.0 dB

SW 0.0 dB

BASS 0.0 dB

TRE 0.0 dB

SLP OFF

Page 33

Settings for the HDMI

(SET HDMI menu)

You can use the SET HDMI menu to make various adjustments for HDMI settings. Select “SET HDMI” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 30) and “Overview of the menus” (page 31).

SET HDMI menu parameters

x CONTROL FOR HDMI (Control

for HDMI)

Lets you turn the Control for HDMI function on or off. For details, see “Preparing for the “BRAVIA” Sync” (page 42).

x VOL LIM (Volume limits)

Lets you set the volume limit of your receiver. For details, see “Using the Volume Limit function” (page 44).

x P.SAVE (Power Save)

Lets you save the power comsumption during power standby mode while Control for HDMI function is set to on. For details, see “Using the Power Saving function (Power Save)” (page 45).

Settings for the Auto Calibration

(A.CAL menu)

You can use the A.CAL menu to make settings for the Auto Calibration function to suit your preference. Select “A.CAL” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 30) and “Overview of the menus” (page 31).

A.CAL menu parameters

x START (Auto Calibration start)

Lets you start the Auto Calibration function. For de tails, see “Pe rforming Auto Calibr ation” (page 23).

x A.CAL CLR (Clear Auto

Calibration result)

Lets you delete the Auto Calibration result. For details on the operation, see “Clearing the measurement result” (page 25).

Amplifier Operations

Page 34

Settings for the Speaker

(SP SETUP menu)

You can use the SP SETUP menu to set the distance of the speakers connected to this receiver. Select “SP SETUP” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 30) and “Overview of the menus” (page 31).

SP SETUP menu parameters

x CNT SP (Center speaker)

Lets you select the center speaker.

x SUR SP (Surround speaker)

Lets you select the surround speakers.

x FL DIST (Front left speaker

distance)

x FR DIST (Front right speaker

distance)

Lets you set the distance from your listening position to the front speaker (A). If both front speakers are not placed an equal distance from your listening position, set the distance to the closest speaker.

x SR DIST (Surround right speaker

distance)

x SL DIST (Surround left speaker

distance)

Lets you set the distance from your listening position to the surround speakers.

x SW DIST (Subwoofer distance)

Lets you set the distance from your listening position to the subwoofer.

Notes

• “CNT DIST” does not appear when you set

“CNT N” in the “SP SETUP” setting.

• “SR DIST” and “SL DIST” do not appear when

you set “SUR N” in the “SP SETUP” setting.

Tip

When the Auto Calibration result is saved, you can adjust the speakers distance in 1 cm steps. If the Auto Calibration result is not saved, you can adjust the speakers distance in 10 cm steps.

A A

30˚30˚

100˚-120˚100˚-120˚

x CNT DIST (Center speaker

distance)

Lets you set the distance from your listening position to the center speaker.

Page 35

Adjusting the level

(LEVEL menu)

You can use the LEVEL menu to adjust the level of each speaker. Select “LEVEL” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 30) and “Overview of the menus” (page 31).

LEVEL menu parameters

x T. TONE (Test tone)

Lets you adjust the speaker levels while listening to the test tone from your listening position. For details, see “8: Adjusting the speaker levels (TEST TONE)” (page 26).

x FL LVL (Front left speaker level)

x CNT LVL (Center speaker level)

x FR LVL (Front right speaker

level)

x SR LVL (Surround right speaker

level)

Adjusting the tone

(TONE menu)

You can use the TONE menu to adjust the tonal quality (bass/treble level) of the speakers. Select “TONE” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 30) and “Overview of the menus” (page 31).

TONE menu parameters

x BASS (Bass level)

x TREBLE (Treble level)

Amplifier Operations

x SL LVL (Surround left speaker

level)

x SW LVL (Subwoofer level)

Notes

• “CNT LVL” does not appear when you set “CNT N” in the “SP SETUP” setting.

• “SR LVL” and “SL LVL” do not appear when you set “SUR N” in the “SP SETUP” setting.

Page 36

Settings for the Custom Menu

(CUSTOM menu)

You can use the CUSTOM menu to make settings for the audio to suit your preference. Select “CUSTOM” in the amplifier menus. For details on adjusting the parameters, see “Navigating through menus” (page 30) and “Overview of the menus” (page 31).

CUSTOM menu parameters

x DUAL (Digital broadcast

language selection)

Lets you select the language you want to listen to during digital broadcast. This feature only functions for Dolby Digital sources.

•MAIN (Main) Sound of the main language will be output.

• SUB (Sub) Sound of the sub language will be output.

• MAIN/SUB (Main/Sub) Sound of the main language will be output through the front left speaker and sound of the sub language will be output through the front right speaker simultaneously.

x A/V SYNC (Synchronizes audio

with video output)

Lets you delay the audio output so that the time gap between the audio output and visual display is minimized. You can adjust from OFF, 1 (10 ms) to 20 (200 ms) in 1 (10 ms) steps.

Notes

• You may not be able to adjust the delay between

sound and image perfectly using this function.

• This function is useful only for Dolby Digital, DTS

and Linear PCM (2ch) input by optical and coaxial audio input signals.

x AUD. DRC (Audio dynamic range

compressor)

Lets you compress the dynamic range of the sound track. This may be useful when you want to watch movies at low volumes late at night. Dynamic range compression is possible with Dolby Digital sources only.

•DRC OFF The dynamic range is not compressed.

•DRC STD The dynamic range is compressed as intended by the recording engineer.

•DRC MAX The dynamic range is compressed dramatically.

Tip

Dynamic range compressor lets you compress the dynamic range of the soundtrack based on the dynamic range information included in the Dolby Digital signal. “DRC STD” is the standard setting, but it only enacts light compression. Therefore, we recommend using the “DRC MAX” setting. This greatly compresses the dynamic range and lets you view movies late at night at low volumes. Unlike analog limiters, the levels are predetermined and provide a very natural compression.

x DIMMER (Brightness of the

display)

Lets you on and off the brightness of the display. For details, see “Changing the brightness of the display (DIMMER)” (page

46).

x DISPLAY (Display)

Lets you turn on and off the display. For details, see “Changing the display setting (DISPLAY)” (page 47).

x SLEEP (Sleep timer)

Lets you set the timer to power off the receiver automatically. For details, see “Using the Sleep Timer (SLEEP)” (page 47)

x IN MODE (Switching the audio

input mode)

Lets you set the audio input mode of inputs. For details, see “Switching between digital and analog audio (IN MODE)” (page 48). This parameter is only available when SAT input is selected.

Page 37

GUIDE

SOUND

FIELD

AMP MENU

ENTER

Enjoying Surround Sound

Selecting the sound field

This receiver can create multi channel surround sound. You can select one of the optimized sound fields from the receiver’s preprogrammed sound fields.

CLEAR

Press SOUND FIELD repeatedly to select the sound field you want.

For details, see “Types of sound field available” (page 37).

Types of sound field available

Sound field for

A.F.D. mode 2CH Stereo

Movie MOVIE-D.C.S.- *

Music SPORTS [SPORTS] Reproduces the feeling of sports broadcasting.

*D.C.S. technology is used. For details, see “Glossary” (page 49).

Sound field

Effect

[Display]

When multi channel surround formats are input, the signals are

[2CH ST]

A.F.D. STD [A.F.D. STD]

downmixed to 2 channel.

Presents the sound as it was recorded/encoded without adding any surround effects. However, this receiver will generate a low frequency signal for output to the subwoofer when there is no LFE signals.

AFD multi [A.F.D. MULT]

PRO LOGIC [DOLBY PL]

PRO LOGIC II MOVIE [PLII MV]

Reproduce sound from any of the format to 2 or more speakers.

Performs Dolby Pro Logic decoding. The source recorded in 2 channel format is decoded into 4.1 channels.

Performs Dolby Pro Logic II Movie mode decoding. This setting is ideal for movies encoded in Dolby Surround. In addition, this mode can reproduce sound in 5.1 channel for watching videos of overdubbed or old movies.

PRO LOGIC II MUSIC [PLII MS]

MULTI STEREO

Performs Dolby Pro Logic II Music mode decoding. This setting is ideal for normal stereo sources such as CDs.

Outputs 2 channel left/right signals from all speakers.

[MULTI ST.]

The system reproduces the sound characteristics of the Sony

[MV-D.C.S.-]

Pictures Entertainment “Cary Grant Theater” cinema production studio. This is a standard mode, great for watching almost any type of movie.

NEWS [NEWS] The systems provided the clearer sound for the voice program

such as news.

PORTABLE AUDIO ENHANCER [P.AUDIO]

Reproduces a clear enhanced sound image from your portable audio device. This mode is ideal for MP3 and other compressed music.

SOUND FIELD

Enjoying Surround Sound

continued

Page 38

Notes

123

ENTER

VIDEO1 VIDEO2 BD DVD

RETURN/EXIT

TV CH

–

PRESET

–

TV CH

PRESET

TUNING

–

TUNING

REPLAY ADVANCE

F1MENUTOP MENU F2

AMP MENU

CLEAR

DISPLAY MUTING

MASTER VOL

TV VOL

SOUND

FIELD

FAVORITESWIDE

PICTURE

JUMP

THEATER

SA-CD/CDTV TUNER

TOOLS/ OPTIONS

MENU/HOME

SAT

BD/DVD

• The effects provided by the virtual speakers may cause increased noise in the playback signal.

• When listening with sound fields that employ the virtual speakers, you will not be able to hear any sound coming directly from the surround speakers.

• This function does not work when: – signals with a sampling frequency of more than

48 kHz is input.

– the multi channel Linear PCM signals are

received via an HDMI IN jack.

• The sound is not output from multiple speakers depending on the source.

• Depending on the disc or source, when you select “AUTO”, the beginning of the sound may be cut off as the optimum mode is automatically selected. To avoid cutting the sound, select “A.F.D. STD.”.

• When the input signal is multi channel source, Dolby Pro Logic II MOVIE/MUSIC are canceled and the multi channel source is output directly.

• When the bilingual broadcast sound is input, Dolby Pro Logic II MOVIE/MUSIC are not effective.

• Multi channel Linear PCM is not available for “P. AUDIO.”

• Depending on the input stream, the decoding mode may not be effective.

• When you select “MV-D.C.S.-” depending on the input stream, Dolby Pro Logic may be applied automatically.

Tip

You can identify the encoding format of DVD software, etc., by looking at the logo on the package.

Tuner Operations

Listening to FM/AM radio

You can listen to FM and AM broadcasts through the built-in tuner. Before operation, make sure you have connected the FM and AM antennas to the receiver (page 21).

Tip

The tuning scale for direct tuning differs depending on the area code as shown in the following table. For details on area codes, see page 4.

Area code FM AM

U, CA 100 kHz 10 kHz*

* The AM tuning scale can be changed (page 40).

Tuning into a station automatically (Auto Tuning)

TUNER

GUIDE

To turn off the surround effect for movie/music

Press SOUND FIELD to select “2CH ST” or “A.F.D. STD.”.

DISPLAY

,V,v,B,b

TUNING –

MENU/ HOME

TUNING +

1 Press TUNER repeatedly to

select the FM or AM band.

You can also use INPUT SELECTOR on the receiver.

Page 39

2 Press TUNING + or TUNING –.

123

ENTER

VIDEO1 VIDEO2 BD DVD

RETURN/EXIT

TV CH

–

PRESET

–

TV CH

PRESET

TUNING

–

TUNING

REPLAY ADVANCE

F1MENUTOP MENU F2

AMP MENU

CLEAR

DISPLAY MUTING

MASTER VOL

TV VOL

SOUND

FIELD

FAVORITESWIDE

PICTURE

JUMP

THEATER

SA-CD/CDTV TUNER

TOOLS/ OPTIONS

MENU/HOME

SAT

BD/DVD

Press TUNING + to scan from low to high; press TUNING – to scan from high to low. The receiver stops scanning whenever a station is received. To stop the automatic tuning manually, press TUNING + or –.

If an FM program is noisy

If an FM program is noisy, you can select monaural reception. There will be no stereo effect, but reception will improve.

Presetting radio stations

You can preset up to 20 FM stations and 10 AM stations. Then you can easily tune in the stations you often listen to.

Presetting radio stations

TUNER

1 Press MENU/HOME. 2 Press V/v repeatedly until “FM

MODE” appears, then press or b.

3 Press V/v repeatedly to select

“MONO”.

• STEREO: stereo reception.

• MONO: monaural reception. The default setting is STEREO.

4 Press . 5 Press MENU/HOME.

Tip

To improve reception, reorient the supplied antennas (aerials).

Numeric buttons

DISPLAY

V,v,B,b

PRESET +/–

GUIDE

MENU/ HOME

TUNING +/–

1 Press TUNER repeatedly to

select the FM or AM band.

You can also use INPUT SELECTOR on the receiver.

2 Press and hold TUNING + or

TUNING – until the auto scanning starts.

Scanning stops when the receiver tunes in a station. “ST” (for stereo program) light up in the display.

3 Press MENU/HOME. 4 Press V/v repeatedly until

“MEMORY” appears in the display.

continued

Tuner Operations

Page 40

5 Press or b.

A preset number appears in the display.

6 Press V/v to select the preset

number you want.

You can select the preset number directly by pressing the number buttons.

7 Press .

“COMPLETE” appears in the display, and the station is stored.

8 Press MENU/HOME. 9 Repeat 2 to 8 to store other

stations.

Tuning to preset stations

1 Press TUNER repeatedly to

select the FM or AM band.

2 Press PRESET + or PRESET –

repeatedly to select the preset station you want.

Each time you press the button, the receiver tunes in one preset station. You can also press the numeric buttons to select the preset station you want. Then, press to enter the selection.

Naming preset station

To change the preset number

Restart from step 3.

Changing the AM tuning interval

The AM tuning interval can be set to either 10 kHz or 9 kHz.

1 Press TUNER/BAND repeatedly

until “AM” appears in the display.

2 Press MENU/HOME. 3 Press V/v repeatedly until “AM

STEP” appears in the display, then press or b.

“9K STEP” or “10K STEP” appears in the display.

4 Press .

“COMPLETE” appears in the display. The AM tuning interval is changed.

5 Press MENU/HOME.

Note

If you change the interval, AM preset stations will be erased.

You can enter a name for preset stations. These names (for example, “XYZ”) appear in the display when a station is selected. Note that no more than one name can be entered for each preset station.

1 Press TUNER repeatedly to

select the FM or AM band.

You can also use INPUT SELECTOR on the receiver.

2 Press PRESET + or PRESET –

repeatedly to select the preset station you want to create an index name for.

3 Press MENU/HOME. 4 Press V/v repeatedly to select

“NAME IN”.

5 Press .

Page 41

6 Create a name by using

V/v/B/b.

Press V/v to select a character, then press b to move the cursor to the next position.

Letters, numbers and other symbols can be input for a radio station name.

If you enter a wrong character

Press B/b repeatedly until the character to be changed flashes, then press V/v to select the desired character. To erase the character, press B/b repeatedly until the character to be erased flashes, then press CLEAR.

7 Press .

“COMPLETE” appears in the display and the station name is stored.

8 Press MENU/HOME.

Viewing the station name or frequency in the display

When the receiver is set to “FM” or “AM”, you can check the frequency using the display.

Press DISPLAY.

Each time you press DISPLAY, the display changes as shown. Station name

This is displayed if you have entered a name for a preset station.

Returns to the original display when several seconds have elapsed.

a) y

Frequency

Using “BRAVIA” Sync features

What is “BRAVIA” Sync?

“BRAVIA” Sync is compatible with a Sony TV, Blu-ray Disc/DVD Player, AV amplifier, etc., that is equipped with the Control for HDMI function. By connecting Sony components that are compatible with the “BRAVIA” Sync with an HDMI cable (not supplied), operation is simplified as follows:

• One-Touch Play: When you play back a component such as a DVD/Blu-ray disc player, the receiver and the TV are turned on automatically and switched to the appropriate HDMI input. Be sure that the System Audio Control setting is set to on.

• System Audio Control: While watching TV, you can select to output the sound from the TV speaker or the speakers connected to the receiver.

• System Power Off: When you turn off the TV, the receiver and connected components are also turned off simultaneously.

Control for HDMI is a mutual control function standard used by HDMI CEC (Consumer Electronics Control) for HDMI (HighDefinition Multimedia Interface).

The Control for HDMI function does not work in the following cases:

• When you connect the receiver to a component which does not correspond with Sony’s Control for HDMI function.

• When you connect the receiver and components using other than HDMI connection.

Using “BRAVIA” Sync features

We recommend that you connect the receiver to products featuring “BRAVIA” Sync.

Note

Depending on the connected component, the Control for HDMI function may not work. Refer to the operating instructions of the component.

Page 42

Preparing for the “BRAVIA” Sync

To use the “BRAVIA” Sync, set the Control for HDMI function to on for both the receiver and the connected component. The receiver is compatible with the “Control for HDMI-Easy Setting” function.

When your TV is compatible with the “Control for HDMI-Easy Setting” function

When you connect a Sony TV with the “Control for HDMI-Easy Setting” function, the Control for HDMI function of the receiver can be turned on simultaneously by turning the Control for HDMI function of the TV on.

1 Make sure that the receiver, TV, and

playback components are connected using an HDMI cable (not supplied). (The respective components must be compatible with the Control for HDMI function.)

2 Turn on the receiver, TV and playback

components.

3 Turn the Control for HDMI function of

the TV on.

The Control for HDMI function of this receiver and all the connected components are simultaneously turned on. During setup, “SCANNING” appears in the display, and once setting is completed, “COMPLETE” will appear. Wait until the setup is complete.

For details on setting the TV, refer to the operating instructions supplied with the TV.

When your TV is not compatible with the “Control for HDMI-Easy Setting” function

Turn the Control for HDMI function of the receiver and the connected component on individually.

SOUND

AMP MENU

ENTER

TOOLS/ OPTIONS

MASTER VOL

MENU/HOME

FIELD

TV VOL

AMP MENU

,V,v,B,b

CLEAR

DISPLAY MUTING

RETURN/EXIT

1 Perform the steps given in “When your

TV is compatible with the “Control for HDMI-Easy Setting” function” (page

42).

2 Press AMP MENU.

“SET HDMI” appears on the display.

3 Press or b to enter the menu.

4 Press V/v repeatedly to select

“CONTROL FOR HDMI”.

“CONTROL FOR HDMI” scrolls across the display, then “CONTROL” appears.

5 Press or b to enter the parameter.

6 Press V/v repeatedly to select “CTRL

ON”.

Control for HDMI function is activated.

7 Set the Control for HDMI function of the

connected component to on.

8 Select the HDMI input (BD, DVD, SAT)

of the receiver and TV to match the HDMI output of the connected component, so that the image from the connected component is displayed.

For details on setting the TV and connected components, refer to the operating instructions of the respective component.

Page 43

Notes

• You cannot perform One-Touch Play and System Audio Control during Control for HDMI-Easy Setting operation.

• Before you do the Control for HDMI-Easy Setting from the TV, be sure to turn on the TV, connected components and receiver.

• When you unplug the HDMI cable or change the connection, perform the steps given in “When your TV is compatible with the “Control for HDMIEasy Setting” function” (page 42) or “When your TV is not compatible with the “Control for HDMIEasy Setting” function” (page 42).

• If the playback components cannot function after you have made the settings for Control for HDMIEasy Setting, check the Control for HDMI setting on your TV.

• If the connected components do not support the Control for HDMI-Easy Setting, you need to set the Control for HDMI function for the connected components to on before you perform the Control for HDMI-Easy Setting from the TV.

Playing back components with one-touch operation

(One-Touch Play)

You can enjoy sound and image from the components connected to the receiver via HDMI connections by a simple operation.

Play back a connected component.

The receiver and the TV are turned on automatically and switched to the appropriate HDMI input.

Note

Be sure that the System Audio Control setting is set to on.

Watching a DVD/Blu-ray disc by simple operation

You can also select a connected component, such as a DVD/Blu-ray disc player using the TV menu. In this case, the receiver and the TV switch to the appropriate HDMI input.

Note

Depending on the TV, the start of the content may not be output.

Tip

You can enjoy the components that are connected to the HDMI jacks, even if you turn the receiver off. The ACTIVE STANDBY indicator lights up in amber.

Using “BRAVIA” Sync features

Page 44

Enjoying the TV sound from the speakers connected to the receiver

(System Audio Control)

You can enjoy the TV sound from the speakers connected to the receiver by a simple operation. You can operate System Audio Control function using the TV menu. For details, refer to the operating instructions supplied with the TV. When System Audio Control function is turned on, the receiver will turns on and switches to the appropriate input automatically. TV sound is output from the speakers connected to the receiver, and the volume of the TV is minimized simultaneously. You can use the System Audio Control function as follows.

• If you turn on the receiver while the TV is turned on, the System Audio Control function will automatically be set to on and the TV sound will output from the speakers connected to the receiver. However, if you turn off the receiver, the sound will output from the TV speakers.

• You can adjust the receiver’s volume when you adjust the TV volume.

Notes

• If System Audio Control does not function

according to your TV setting, refer to the operating instructions supplied with the TV.

• When you connect a TV that does not have System

Audio Control function, the System Aud io Control functi on does not work.

• If the TV is turned on before turning on the

receiver, the TV sound will not be output for a moment.

Using the Volume Limit function

When the System Audio Control function is active, and the output method changes from the TV speaker to the speakers connected to the receiver automatically, loud sound may be output depending on the volume level of the receiver. You can prevent this by limiting the maximum volume level.

1 Press AMP MENU. 2 Press v/V repeatedly until “SET

HDMI” appears, then press or b.

3 Press v/V repeatedly until “VOL

LIM” appears, then press or b.

4 Press v/V repeatedly to select

the maximum volume level you want.

The maximum volume level changes as follows:

MAX y 39 y 38 y ...... y 2 y 1

y MIN

5 Press AMP MENU.

The AMP MENU turns off.

Notes

• This function is available only when the Control for HDMI function is set to on.

• This function is not available when the output method changes from the speakers connected to the receiver to the TV speaker.

Tips

• Sony recommends that you set the maximum volume level to a little lower than the volume you usually listen to.

• Regardless of the maximum volume level you set, the MASTER VOLUME on the receiver and the MASTER VOL +/– button of the remote are operable.

• If you do not want to limit the maximum volume level, select “MAX.”

Page 45

Turning off the receiver with the TV

(System Power Off)

When you turn the TV off by using the POWER button on the TV’s remote, the receiver and the connected components turn off automatically. You can also use the receiver’s remote to turn off the TV.

?/1

DMPORT

TV INPUT

VIDEO1 VIDEO2 BD DVD

SAT

BD/DVD

PICTURE

JUMP

123

CLEAR

DISPLAY MUTING

?/1

SYSTEM STANDBY

SA-CD/CDTV TUNER

F1MENUTOP MENU F2

FAVORITESWIDE

THEATER

GUIDE

SOUND

FIELD

AMP MENU

ENTER

TOOLS/ OPTIONS

TV VOL

MASTER VOL

TV ?/1

Using the Power Saving function

(Power Save)

You can reduce the receiver’s power consumption when you connect a “BRAVIA” Sync-compatible TV to this receiver during active standby mode if the TV is turned off and HDMI signal transmission is stopped.

AMP MENU

ENTER

TOOLS/ OPTIONS

MASTER VOL

MENU/HOME

GUIDE

SOUND

FIELD

TV VOL

AMP MENU

V,v,B,b

CLEAR

DISPLAY MUTING

RETURN/EXIT

1 Press AMP MENU.

“SET HDMI” appears on the display.

2 Press or b to enter the

menu.

Using “BRAVIA” Sync features

RETURN/EXIT

TV CH

PRESET

TUNING

MENU/HOME

–

REPLAY ADVANCE

–

TV CH

PRESET

TUNING

Press TV and TV ?/1 at the same time.

The TV, receiver and the components connected via HDMI are turned off.

Notes

• Set the TV Standby Synchro to “ON” before using the System Power Off function. For details, refer to the operating instructions supplied with the TV.

• Depending on the status, the connected components may not be turned off. For details, refer to the operating instructions supplied with the connected components.

3 Press V/v repeatedly to select

“P.SAVE”, then press

or b.

4 Press V/v repeatedly to select

the setting, then press

• SAVE ON: Reduces power consumption in standby mode. HDMI signal transmission occurs only when the TV is on.

• SAVE OFF: No reduction. HDMI signal transmission occurs continuously.

or b.

5 Press AMP MENU.

The AMP MENU turns off.

continued

Page 46

Notes

• The power saving function may not work for some TVs compatible with the “BRAVIA” Sync. In this case, set “P.SAVE” to “SAVE OFF.”

• Depending on your components, it may take time before image or sound is output.

• This function is available only when the Control for HDMI function is set to on.

Other Operations

Changing the brightness of the display

(DIMMER)

You can change the brightness of the display.

1 Press AMP MENU.

“SET HDMI” appears on the display.

2 Press V/v repeatedly until

“CUSTOM” appears, then press

or b.

3 Press V/v repeatedly until

“DIMMER” appears, then press

or b.

4 Press V/v repeatedly to select

the brightness of the display, then press .

• DIMMER Y: Low lighting.

• DIMMER N: Bright lighting.

5 Press AMP MENU.

The AMP menu turns off.

Page 47

Changing the display setting

(DISPLAY)

You can change the display setting.

1 Press AMP MENU.

“SET HDMI” appears on the display.

2 Press V/v repeatedly until

“CUSTOM” appears, then press

or b.

3 Press V/v repeatedly until

“DISPLAY” appears, then press

or b.

4 Press V/v repeatedly to change

the display setting, then press

• DSPL ON: the display appears all the time.

• DSPL OFF: the display appears when you operate the receiver.

5 Press AMP MENU.

The AMP menu turns off.

Using the Sleep Timer

(SLEEP)

You can set the receiver to turn off at a preset time when you sleep while listening to music. You can preset the time in 10 minutes decrements.

1 Press AMP MENU.

“SET HDMI” appears on the display.

2 Press V/v repeatedly until

“CUSTOM” appears, then press

or b.

3 Press V/v repeatedly until

“SLEEP” appears, then press

or b.

4 Press V/v repeatedly to select

the preset time.

The minutes display (the remaining time) changes as follows:

SLP OFF y SLP 10M y SLP 20M

SLP 90M y SLP 80M ...... SLP 30M

Other Operations

5 Press . 6 Press AMP MENU.

The AMP menu turns off.

Page 48

Switching between

123

ENTER

SYSTEM STANDBY

TV INPUT

DMPORT

VIDEO1 VIDEO2 BD DVD

RETURN/EXIT

F1MENUTOP MENU F2

AMP MENU

CLEAR

DISPLAY MUTING

MASTER VOL

TV VOL

SOUND

FIELD

FAVORITESWIDE

PICTURE

JUMP

THEATER

SA-CD/CDTV TUNER

?/1

TOOLS/ OPTIONS

MENU/HOME

SAT

BD/DVD

digital and analog audio

(IN MODE)

You can select the audio input mode setting when you connect satellite tuner or set-top box to both digital and analog audio input jacks on the receiver and SAT input has been selected.

1 Press AMP MENU.

“SET HDMI” appears on the display.

2 Press V/v repeatedly to select

“CUSTOM”.

3 Press or b to enter the

menu.

4 Press V/v repeatedly to select

“IN MODE”.

Using the Remote

Changing the input button assignments

You can change the factory settings of the input buttons to suit the components in your system. For example, if you connect a Blu-ray Disc player to the DVD jack on the receiver, you can set the DVD button on this remote to control the Blu-ray Disc player.

Notes

• You can change the remote assignments for BD, DVD and SAT input buttons.

• When the receiver is in VIDEO1, VIDEO2 or SA-CD/CD mode, you cannot operate the selected component.

5 Press or b to enter the

parameter.

6 Press V/v repeatedly to select

the audio input mode you want.

7 Press AMP MENU.

The AMP menu turns off.

Audio input modes

x AUTO

Gives priority to HDMI audio signals if there are both digital (HDMI and optical) connections.

x OPT

Specifies the digital audio signals input to the DIGITAL SAT OPT IN jack.

DMPORT

Numeric button

GUIDE

?/1

Input buttons

MASTER VOL –

1 Hold down the input button of

which you want to change the assignment.

Example: Hold down DVD.

Page 49

2 Referring to the following table,

press the corresponding button for the category you want.

Example: Press 3. Now you can use the DVD button to control the Blu-ray Disc player.

Categories and the corresponding buttons for BD, DVD, and SAT

Categories Press

DVD player (command mode DVD1)

DVD recorder (command mode DVD3)

Blu-ray disc player (command mode BD1)

Blu-ray disc recorder (command mode BD3)

DVR (Digital CATV terminal)

DSS (Digital Satellite Receiver)

The default setting of the DVD button. Sony DVD recorders are operated with a D VD1 or DVD3 setting. For details, refer to the operating instructions of the DVD recorders.

The default setting of the BD button. For details on the BD1 or BD3 setting, refer to the operating instructions of the Blu-ray Disc player or Blu-ray Disc recorder.

The default setting of the SAT button.

Additional Information

Glossary

x Digital Cinema Sound (DCS)

A unique sound reproduction technology for home theater developed by Sony, in cooperation with Sony Pictures Entertainment, for enjoying the exciting and powerful sound of movie theaters at home. With this “Digital Cinema Sound” developed by integrating a DSP (Digital Signal Processor) and measured data, the ideal sound field intended by filmmakers can be experienced at home.

x Dolby Digital

Digital audio encoding/decoding technology developed by Dolby Laboratories, Inc. It consists of front (Left/Right), center, surround (Left/Right) and subwoofer channels. It is a designated audio standard for DVD-video and also known as 5.1 channel surround. Since surround information is recorded and reproduced in stereo, more realistic sound with fuller presence is delivered than with Dolby surround.

x Dolby Pro Logic II

This technology converts 2 channel stereo recorded audio into 5.1 channel for playback. There is a MOVIE mode for movies and MUSIC mode for stereo sources such as music. Old movies encoded in the traditional stereo format can be enhanced with 5.1 channel surround sound.

Using the Remote/Additional Information

To clear all remote button assignments

Press and hold MASTER VOL –, then press ?/1 and DMPORT at the same time. The remote is reset to its factory settings.

x Dolby Surround (Dolby Pro

Logic)

Audio processing technology developed by Dolby Laboratories, Inc. Center and mono surround information is matrixed into two stereo channels. When reproduced, audio is decoded and output in 4 channel surround sound. This is the most common audio processing method for DVD-video.

continued

Page 50

x DTS Digital Surround

Digital audio encoding/decoding technology for theaters developed by DTS, Inc. It compresses audio less than Dolby Digital, delivering a higher quality sound reproduction.

x HDMI (High-Definition

Multimedia Interface)

HDMI (High-Definition Multimedia Interface) is an interface that supports both video and audio on a single digital connection, allowing you to enjoy high quality digital picture and sound. The HDMI specification supports HDCP (High-bandwidth Digital Contents Protection), a copy protection technology that incorporates coding technology for digital video signals.

x L.F.E. (Low Frequency Effects)

Sound effects of low frequencies which are output from a subwoofer in Dolby Digital or DTS, etc. By adding a deep bass with a frequency between 20 to 120 Hz, audio becomes more powerful.

x Sampling frequency

To convert analog audio to digital, analog data should be quantified. This process is called sampling, and the number of times per second the analog data is quantified is called the sampling frequency. A standard music CD stores data quantified at 44,100 times per second, which is expressed as a sampling frequency of 44.1 kHz. Generally speaking, a higher sampling frequency means better sound quality.

x TSP (Time Stretched Pulse)

A TSP signal is a highly precise measuring signal that utilizes impulse energy, measuring a wide band, from low to high, in a short period. The amount of energy used to measure signals is important to ensure measurement accuracy in a normal indoor environment. Using TSP signals makes it possible to measure signals effectively.

x x.v.Color

x.v.Color is a more familiar term for the xvYCC standard proposed by Sony, and is a trademark of Sony. xvYCC is an international standard for colour space in video. This standard can express a wider colour range than the currently used broadcast standard.

x S-master

S-master is an all-digital amplifier technology developed by Sony, which effectively minimizes the occurrence of sound fragmentation and jitter, delivering superb dialog clarity and faithful reproduction of the original sound. The compact amplifier section supports a higher power efficiency and improved thermal performance.

Page 51

Precautions

On safety

Should any solid object or liquid fall into the cabinet, unplug the receiver and have it checked by qualified personnel before operating it any further.

On power sources

• Before operating the receiver, check that the operating voltage is identical with your local power supply. The operating voltage is indicated on the nameplate on the back of the receiver.

• The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

• If you are not going to use the receiver for a long time, be sure to disconnect the receiver from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord.

• (Models of area code U, UC, CA only) One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.

• The AC power cord must be changed only at a qualified service shop.

On heat buildup

Although the receiver heats up during operation, this is not a malfunction. If you continuously use this receiver at a large volume, the cabinet temperature of the top, side and bottom rises considerably. To avoid burning yourself, do not touch the cabinet.

On placement

• Place the receiver in a location with adequate ventilation to prevent heat buildup and prolong the life of the receiver.

• Do not place the receiver near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock.

• Do not place anything on top of the cabinet that might block the ventilation holes and cause malfunctions.

• Do not place the receiver near equipment such as a TV, VCR, or tape deck. If the receiver is being used in combination with a TV, VCR, or tape deck, and is placed too close to that equipment, noise may result, and picture quality may suffer. This is especially likely when using an indoor antenna. Therefore, we recommend using an outdoor antenna.

• Use caution when placing the receiver or speakers on surfaces that have been specially treated (with wax, oil, polish, etc.) as staining or discoloration of the surface may result.

On operation

Before connecting other components, be sure to turn off and unplug the receiver.

If you encounter color irregularity on a nearby TV screen

The center speaker is magnetically shielded to allow it to be installed near a TV set. However, color irregularities may still be observed on certain types of TV sets. As the front, surround speakers and subwoofer are not magnetically shielded, we recommend that you place the surround speakers and subwoofer slightly further away from TV set (page 13).

If color irregularity is observed...

Turn off the TV set, then turn it on again after 15 to 30 minutes.

Additional Information

continued

Page 52

If color irregularity is observed again...

Place the speaker further away from the TV set.

If howling occurs

Reposition the speakers or turn down the volume on the receiver.

On cleaning

Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine.

If you have any questions or problems concerning your receiver, please consult your nearest Sony dealer.

Troubleshooting

If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem.

Audio

There is no sound, no matter which component is selected, or only a very low-level sound is heard.

• Check that the speakers and components are connected securely.

• Check that both the receiver and all components are turned on.

• Check that MASTER VOLUME is not set to “VOL MIN”.

• Press MUTING to cancel the muting function.

• Check that you have selected the correct component with the input buttons.

• The protective device on the receiver has been activated. Turn off the receiver, eliminate the short-circuit problem, and turn on the power again.

• Check that the IN MODE setting is correct for SAT input.

There is no sound from a specific component.

• Check that the component is connected correctly to the audio input jacks for that component.

• Check that the cord(s) used for the connection is (are) fully inserted into the jacks on both the receiver and the component.

Page 53

There is no sound from one of the front speakers.

• Make sure you have connected to both the L and R jacks of an analog component, and not only to either the L or R jack. Use an audio cord (not supplied).

There is no sound from digital sources (from OPTICAL input jack).

• Check that the IN MODE is set to “AUTO” for SAT input.

There is severe hum or noise.

• Check that the speakers and components are connected securely.

• Check that the connecting cords are away from a transformer or motor, and at least 10 feet away from a TV set or fluorescent light.

• Move your audio components away from the TV.

• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.

There is pop noise from a specific component connected to this receiver when you turn on the component.

• Check that the IN MODE is set to “AUTO” for SAT input (page 48).

The surround effect cannot be obtained.

• Make sure the sound field function is on (press SOUND FIELD).

• Sound fields do not function for signals with a sampling frequency of more than 48 kHz.

Dolby Digital or DTS multi channel sound is not reproduced.

• Check that the DVD, etc. you are playing is recorded in Dolby Digital or DTS format.

• When connecting the DVD player, etc., to the digital input jacks of this receiver, check the audio setting (the settings for the audio output) of the connected component.

There is no sound from the component connected to the DIGITAL MEDIA PORT adapter.

• Adjust the volume of this receiver.

• The DIGITAL MEDIA PORT adapter and/or component is not connected correctly. Turn off the receiver, then reconnect the DIGITAL MEDIA PORT adapter and/or component.

• Check the DIGITAL MEDIA PORT adapter and/or component device to make sure it supports this receiver.

There is no sound, or only a very lowlevel sound is heard from the center/ surround speakers.

• Select a MOVIE-D.C.S.- mode (page 37).

• Adjust the speaker level (page 26).

• Check that the speakers are connected securely.

There is no sound from the subwoofer.

• Check that the subwoofer is connected correctly and securely.

Video

There is no picture or an unclear picture appears on the TV screen or monitor.

• Make sure you have connected the video output of your video component to the TV.

• Move your audio components away from the TV.

• Depending on the DIGITAL MEDIA PORT adapter, video output may not be possible.

continued

Additional Information

Page 54

HDMI

The volume turns down when the output method changes from the TV speaker to the speakers connected to the receiver.

• The Volume Limit function is working. For details, see “Using the Volume Limit function” (page 44).

The source sound input to the HDMI jack on the receiver is not output from the receiver or the TV speaker.

• Check the setting of CONTROL FOR HDMI in the SET HDMI menu (page 31).

• Check the HDMI connection (page 18).

• You cannot listen to the Super Audio CD by connecting HDMI.

• Depending on the playback component, you may need to set up the component. Refer to the operating instructions supplied with each component.

The source image input to the HDMI jack on the receiver is not output from the TV.

• Check the HDMI connection (page 18).

• Depending on the playback component, you may need to set up the component. Refer to the operating instructions supplied with each component.

The control for HDMI function does not work.

• Check the HDMI connection (page 18).

• Make sure “CONTROL FOR HDMI” is set to “CTRL ON” in SET HDMI menu.

• Make sure the connected component is compatible with the Control for HDMI function.

• Check the Control for HDMI settings on the connected component. Refer to the operating instructions of the connected component.

• Repeat the procedures of “Preparing for the “BRAVIA” Sync” if you change the HDMI connection, connect/disconnect the AC power cord, or there is a power failure (page 42).

No sound is output from the receiver and TV speaker while using the System Audio Control function.

• Make sure the TV is compatible with the System Audio Control function.

• If you cannot listen to the sound of a component connected to the receiver – Select the appropriate input when you

want to watch a program on a component connected via HDMI connection to the receiver.

– Change the TV channel when you want

to watch a TV broadcast.

– Select the component or input you want

to watch when you watch a program on the component connected to the TV. Refer to the operating instructions of the TV on this operation.

Tuner

The FM reception is poor.

• Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna as shown below. If you connect the receiver to an outdoor antenna, ground it against lightning. To prevent a gas explosion, do not connect the ground wire to a gas pipe.

Outdoor FM antenna

Receiver

ANTENNA

Ground wire (not supplied)

To ground

Page 55

Radio stations cannot be tuned in.

• Check that the antennas are connected securely. Adjust the antennas and connect an external antenna, if necessary.

• The signal strength of the stations is too weak (when tuning in with automatic tuning). Change to monaural reception (page 39).

• No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations). Preset the stations (page 39).

Error messages

If an error message appears while you perform Auto Calibration, see “When error codes appear” (page 25) to solve the problem.

If you are unable to remedy the problem using the troubleshooting guide

Clearing the receiver’s memory may remedy the problem (page 21). However, note that all memorized settings will be reset to their factory settings and you will have to readjust all settings on the receiver.

Remote control

The remote does not function.

• For receiver operation, you can only use the DISPLAY button when the TUNER input is selected.

• Point the remote at the remote sensor on the receiver.

• Remove any obstacles in the path between the remote and the receiver.

• Replace all the batteries in the remote with new ones, if they are weak.

• Make sure you select the correct input on the remote.

Others

The ACTIVE STANDBY lamp is flashing.

• The receiver is in protection mode. Turn off the receiver and turn it on again.

If the problem persist

Consult your nearest Sony dealer. Note that if service personnel changes some parts during repair, these parts may be retained.

Reference sections for clearing the receiver’s memory

To clear See

All memorized settings page 21

Additional Information

Page 56

Specifications

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code U only)

With 3 ohm loads, both channels driven, from 170 – 20,000 Hz; rated 84 watts per channel minimum RMS power, with no more than 1% total harmonic distortion from 250 milliwatts to rated output.

Amplifier section

Models of area code U, CA Power Output Stereo mode (rated) 84 W + 84 W

Surround mode (reference)

(3 ohms at 170 – 20,000 Hz, THD 1%)

RMS Output (3 ohms at 1 kHz, THD 10%) FRONT

CENTER SUR

(1.5 ohms at 70 Hz, THD 10%) SUBWOOFER

: 143 W/ch

: 143 W

: 143 W/ch

: 285 W

Measured under the following conditions:

Area code Power requirements

U, CA 120 V AC, 60 Hz

MX 127 V AC, 60 Hz

Reference power output for front, center, surround speakers and subwoofer. Depending on the sound field settings and the source, there may be no sound output.

Inputs

Analog Sensitivity: 1 V/50 kohms Digital (Coaxial) Impedance: 75 ohms

Tone

Gain levels ±10 dB, 0.5 dB step

Reproduction frequency range:

28 – 20,000 Hz

FM tuner section

Tuning range 87.5 – 108.0 MHz Antenna FM wire antenna Antenna terminals 75 ohms, unbalanced Intermediate frequency

10.7 MHz

AM tuner section

Tuning range

Area code Tuning scale

10 kHz step 9 kHz step

U, CA, MX 530 –

1,710 kHz

531 – 1,710 kHz

Models of area code MX Power Output

Stereo mode (rated) 90 W + 90 W

(3 ohms at 1 kHz, THD 1%)

Surround mode (reference)

RMS Output (3 ohms at 1 kHz, THD 10%)

FRONT CENTER SUR

: 125 W/ch

: 125 W

: 125 W/ch (1.5 ohms at 70 Hz, THD 10%) SUBWOOFER

: 210 W

Antenna Loop antenna Intermediate frequency

450 kHz

General

Power requirements

Area code Power requirements

U, CA 120V AC, 60 Hz

MX 127 V AC, 60 Hz

Power output (DIGITAL MEDIA PORT)

DC OUT: 5 V, 700 mA MAX

Page 57

Power consumption

Area code Power consumption

U, CA 165 W

MX 140 W

Power consumption (during standby mode)

0.3 W (When Control for HDMI is off)

Dimensions (w/h/d) (Approx.)

17 × 2 5/8 × 13 1/8 inches (430 × 66.5 × 333 mm) including projecting parts and controls

Mass (Approx.) 3.4 kg (7 lb 8 oz)

Speaker section

• Front speaker (SS-MSP36S)

• Surround speaker (SS-SRP36S)

• Center speaker (SS-CNP36)

Front/Surround speaker

Full range

Center speaker Full range, Magnetically

shielded Speaker unit Front/Surround speaker

2 5/8 inches (65 mm),

cone type Center speaker 1 3/16 × 2 3/8 inches

(30 × 60 mm), cone type Enclosure type Front/Surround speaker

Bass reflex Center speaker Acoustic suspension

Rated Impedance 3 ohms Dimension (w/h/d) (Approx.) Front/Surround speaker

4 1/8 × 6 1/2 × 3 1/8 inches

(102 × 163 × 77 mm)

(with foot) Center speaker 15 × 2 × 2 5/8 inches

(380 × 50 × 64 mm)

(with foot) Mass (Approx.) Front speaker 0.52 kg (1 lb 3 oz) Surround speaker 0.48 kg (1 lb 1 oz) Center speaker 0.38 kg (0 lb 14 oz)

• Subwoofer (SS-WP36)

Speaker unit 6 3/8 inches (160 mm),

cone type Enclosure type Bass reflex Rated Impedance 1.5 ohms Dimensions (w/h/d) (Approx.)

8 3/4 × 15 5/8 × 12 7/8

inches (220 × 395 × 325

mm) (with foot) Mass (Approx.) 5.6 kg (12 lb 6 oz)

Supplied speakers

Front speaker (2) Center speaker (1) Surround speaker (2) Subwoofer (1)

Supplied accessories

Operating Instructions (this manual) Quick Setup Guide (1) FM wire antenna (1) AM loop antenna (1) Remote commander

• RM-AAU057 (1) R6 (size-AA) batteries (2) Optimizer microphone (ECM-AC2) (1) Speaker cords (5) Foot pads

• Speakers (20)

•Subwoofer (4)

For details on the area code of the component you are using, see page 4.

Design and specifications are subject to change without notice.

Halogenated flame retardants are not used in the certain printed wiring boards.

Additional Information

Page 58

Index

AUTO CALIBRATION 22

Blu-ray disc player

connecting 18 playback 29

CD player

connecting 17 playback 29

Control for HDMI

connecting 18 preparing 42

Digital Cinema Sound

(DCS) 37, 49 DIMMER 46 DISPLAY 47 Dolby Digital 49 DTS 50 DVD player

connecting 20 playback 29

DVD recorder

connecting 20 playback 29

Error messages 55

HDMI

connecting 18 Control for HDMI 33

IN MODE 48 Initial setup 21

A.CAL 33 CUSTOM 36 LEVEL 35 SET HDMI 33 SP SETUP 34 TONE 35

Muting 27

One-Touch Play 43

Power Save 45

Remote commander 9

Satellite tuner/Set-top box

connecting 18 enjoying 28

Selecting

component 27 Sleep Timer 47 Speakers

connecting 15 Super Audio CD player

connecting 17

playback 29 System Audio Control 44 System Power Off 45

TEST TONE 26 Tuner

connecting 21

Tuning

automatically 38 to preset stations 40

connecting 16, 17 enjoying 28

VCR

connecting 20 playback 29

Volume Limit 44

Page 59

Page 60

Sony Corporation Printed in Malays ia

(1)

Sony HTSS360 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Description and location of parts

Getting Started

1: Installing the speakers

2: Connecting the speakers

3: Connecting the TV

6: Preparing the receiver and the remote

Playback

Selecting a component

Enjoying sound/images from the components connected to the receiver

Amplifier Operations

Navigating through menus

Enjoying Surround Sound

Selecting the sound field

Tuner Operations

Listening to FM/AM radio

Presetting radio stations

Using “BRAVIA” Sync features

What is “BRAVIA” Sync?

Preparing for the “BRAVIA” Sync

Other Operations

Using the Remote

Changing the input button assignments

Additional Information

Glossary

Precautions

Troubleshooting

Specifications

Index