Sony HT-CT80 Users guide

Sound Bar

Operating Instructions

GB

使用說明書

CT

HT-CT80

WARNING

Do not install the appliance in a
confined space, such as a bookcase or
built-in cabinet.

To reduce the risk of fire, do not cover
the ventilation opening of the appliance
with newspapers, tablecloths, curtains,
etc.
Do not expose the appliance to naked
flame sources (for example, lighted
candles).

To reduce the risk of fire or electric
shock, do not expose this appliance to
dripping or splashing, and do not place
objects filled with liquids, such as vases,
on the appliance.

The unit is not disconnected from the
mains as long as it is connected to the
AC outlet, even if the unit itself has been
turned off.

As the main plug is used to disconnect
the unit from the mains, connect the
unit to an easily accessible AC outlet.
Should you notice an abnormality in the
unit, disconnect the main plug from the
AC outlet immediately.

Do not expose batteries or appliances
with battery-installed to excessive heat,
such as sunshine and fire.

Indoor use only.

For the Bar Speaker

The nameplate is located on the
bottom.

Copyrights and Trademarks

This system incorporates Dolby* Digital
Surround System.

* Manufactured under license from

Dolby Laboratories.
Dolby, and the double-D symbol are
trademarks of Dolby Laboratories.

The BLUETOOTH® word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Sony Corporation is under
license.

The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the
United States and in other countries.

Android™ is a trademark of Google Inc.

“ClearAudio+” is a trademark of Sony
Corporation.

MPEG Layer-3 audio coding technology
and patents licensed from Fraunhofer
IIS and Thomson.

Windows Media is either a registered
trademark or trademark of Microsoft
Corporation in the United States and/or
other countries.
This product is protected by certain
intellectual property rights of Microsoft
Corporation. Use or distribution of such
technology outside of this product is
prohibited without a license from
Microsoft or an authorized Microsoft
subsidiary.

Other trademarks and trade names are
those of their respective owners.

GB

2

About these operating instructions

•The instructions in these Operating
Instructions describe the controls on
the remote control. You can also use
the controls on the main unit if they
have the same or similar names as
those on the remote control.

•Some illustrations are presented as
conceptual drawings, and may be
different from the actual products.

GB

GB

3

Table of Contents

About these operating

instructions ...........................3

Getting Started

What’s in the box .......................5

Connecting with a TV and the

subwoofer ............................6

Positioning the system ..............8

Installing the Bar Speaker

on a wall ...............................9

Turning on the system ............. 10

Listening

Listening to sound from a TV,

cable/satellite box, etc. ......11

Listening to music from a

USB device .......................... 12

Listening to music from a

BLUETOOTH device ............ 12

Sound Adjustment

Enjoying sound effects ............ 13

BLUETOOTH Functions

Listening to music from a

BLUETOOTH device ............ 14

Other Functions

Auto standby function ............. 16

Additional Information

Precautions ...............................17

Troubleshooting ....................... 18

Guide to parts and controls ..... 21

Playable types of files ..............24

Supported audio formats ........24

Specifications ...........................25

On BLUETOOTH

communication ..................26

GB

4

Getting Started

Getting Started

What’s in the box

Bar Speaker (1)

Subwoofer (1)

Optical digital cable (1)

R03 (size AAA) batteries (2)

Setting up the remote
control

Remote control (1)

GB

5

Connecting with a TV and the subwoofer

TV, cable box or satellite box

Optical digital cable (supplied)

Subwoofer

When there is an optical digital jack on your TV

Note

• Connect the supplied SS-WCT80 subwoofer only. Do not connect any other subwoofer.

GB

6

Getting Started

When there is no optical digital jack on your TV

TV, cable box or satellite box

Analog audio cable (not supplied)

Subwoofer

Notes

• Connect the supplied SS-WCT80 subwoofer only. Do not connect any other subwoofer.

• If the TV’s headphone jack also serves as an audio output jack, check the TV’s audio
output settings. For details, refer to the TV’s operating instructions.

7

GB

Positioning the system

Bar Speaker

Subwoofer

10 cm

The illustrations below are examples of
how to install the system.

Note

• Place the Bar Speaker so that the top
panel is not blocked.

On a rack

On a wall

See “Installing the Bar Speaker on a
wall” (page 9).

Note on installing the subwoofer

Place the subwoofer so that the rear
panel is at least 10 cm away from the
wall.

8

GB

Getting Started

Installing the Bar

4 mm

More than 30 mm

4.6 mm

Hole on the rear of the Bar Speaker

9 mm

9mm to
10 mm

447 mm

Speaker on a wall

You can mount the Bar Speaker on a
wall.

Notes

• Prepare screws (not supplied) that are
suitable for the wall material and
strength. As a plasterboard wall is
especially fragile, attach the screws
securely to two studs in the wall beam.
Install the Bar Speaker horizontally, hung
by screws in studs in a continuous flat
section of the wall.

• Be sure to subcontract the installation to
Sony dealers or licensed contractors and
pay special attention to safety during the
installation.

• Sony shall not be held responsible for
accidents or damage caused by improper
installation, insufficient wall strength,
improper screw installation or natural
calamity, etc.

1 Prepare screws (not supplied) that

are suitable for the holes on the
rear of the Bar Speaker.

2 Fasten the screws to 2 studs in the

wall.

The screws should protrude by
9 mm to 10 mm.

3 Hang the Bar Speaker on the

screws.

Align the holes at the rear of the Bar
Speaker with the screws, then hang
the Bar Speaker on the two screws.

GB

9

Turning on the system

/ (on/
standby)

1 Connect the AC power cord (mains

lead).

2 Press the / (on/standby)

button.

An input indicator lights up.

10

GB

Listening

Listening

OPTICAL

 (volume)

+/–

Listening to sound from a TV, cable/satellite box, etc.

1 Press the input button of the jack

to which you connected the
device you want to listen.

The indicator of the selected device
lights up.

OPTICAL button

TV that is connected to the OPTICAL jack

ANALOG button

Analog device that is connected to the
ANALOG jack

USB button

USB device that is connected to the

(USB) port (page 12)

(BLUETOOTH) button

BLUETOOTH device that supports A2DP

2 Press  (volume) +/– to adjust the

volume.

Tip

• If you press INPUT on the Bar Speaker, the
device changes cyclically as follows.
OPTICAL  ANALOG  USB 
BLUETOOTH

GB

11

Listening to music from a USB device

Listening to music from a BLUETOOTH device

You can play music files on a connected
USB device.
For playable types of files, see “Playable
types of files” (page 24).

1 Connect the USB device to the

(USB) port.

2 Press USB.
3 Press  (play/pause).
4 Press   to select a folder to

be played.

Note

• Turn off the system before removing the
USB device to avoid data corruption or
damage to the USB device.

Refer to “BLUETOOTH Functions”
(page 14).

12

GB

Sound Adjustment

Sound Adjustment

Enjoying sound effects

To set sound effects, press one of the
sound effects buttons on the remote
control.

Selecting the sound effects

Press SURROUND repeatedly during
playback.

The surround effects change cyclically
as follows.
CLEARAUDIO+
SURROUND Off

CLEARAUDIO+

The suitable sound setting is automatically
selected for the sound source. The
CLEARAUDIO+ indicator lights up.

SURROUND On

Sounds are played back with surround
effects. The SURROUND indicator lights up.

SURROUND Off

The input source is down-mixed for 2
channels. The CLEARAU DIO+ and SURROUND
indicators turn off.

Setting the Night mode

Sounds are played back enhanced with
sound effects and clarity of dialog.

 SURROUND On 

Setting the Voice mode

The Voice mode helps make dialogs
clearer.

Press VOICE.

The ANALOG indicator flashes twice.
To inactivate the Voice mode, press
VOICE again. The OPTICAL indicator
flashes twice.

Selecting multiplex
broadcast sound (Dual
Mono)

You can enjoy multiplex broadcast
sound when the system receives a
Dolby Digital multiplex broadcast signal.

Press AUDIO repeatedly.

The channel changes cyclically as
follows.

 Sub  Main/Sub

Main

Main

Outputs only the main channel. The OPTICAL
indicator flashes twice.

Sub

Outputs only the sub channel. The ANALOG
indicator flashes twice.

Main/Sub

Main sound is output from the left speaker
and sub sound is output from the right
speaker. The USB indicator flashes twice.

Press NIGHT.

The ANALOG indicator flashes twice.
To inactivate the Night mode, press
NIGHT again. The OPTICAL indicator
flashes twice.

13

GB

Setting Dolby DRC (Dynamic
Range Control)

Useful for enjoying movies at low sound
volume. DRC applies to Dolby Digital
sources.

Hold down AUDIO for 5 seconds, then
VOICE for 5 seconds to turn on or off
Dolby DRC.

On

Compresses sound in accordance with the
information contained in the content. The
ANALOG indicator flashes twice.

Off

Sound is not compressed. The OPTICAL
indicator flashes twice.

BLUETOOTH Functions

Listening to music from a BLUETOOTH device

Pairing this system with a
BLUETOOTH device

Pairing is the process required to create
a link between BLUETOOTH devices to
allow wireless connection. You must
pair a device with the system before you
start using the system.
Once BLUETOOTH devices are paired,
there is no need to pair them again.

1 Press PAIRING on the Bar Speaker.

The BLUETOOTH indicator (blue)
flashes quickly during BLUETOOTH
pairing.

2 Turn on the BLUETOOTH function

on the BLUETOOTH device, search
for devices and select “HT-CT80.”

If a Passkey is requested, enter
“0000.”

3 Make sure that the BLUETOOTH

indicator (blue) lights up.

Connection has been established.

Note

• You can pair up to 8 BLUETOOTH
devices. If the 9th BLUETOOTH device
is paired, the least recently
connected device will be replaced by
the new one.

14

GB

BLUETOOTH Functions

Listening to music of the
registered device

1 Press (BLUETOOTH).
2 On the BLUETOOTH device, select

“HT-CT80.”

3 Make sure that the BLUETOOTH

indicator (blue) lights up.

4 Start playback on the BLUETOOTH

device.

Note

• When the sy stem has pairing in formation,
the system is in BLUETOOTH standby
mode even when it is turned off.

Connecting to a BLUETOOTH
device by One-touch
functions (NFC)

By holding an NFC-compatible
BLUETOOTH device near to the N-Mark
on the system, the system and
BLUETOOTH device proceed to
complete pairing and the BLUETOOTH
connection automatically.

Compatible devices

Smartphones, tablets, and music
players with the NFC function built-in
(OS: Android 2.3.3 or later, excluding
Android 3.x)

1 Download, install, and start the

“NFC Easy Connect” application.

Notes

• The application may not be available
in some countries/regions.

• Depending on your BLUETOOTH
device, this operation may not be
required.

2 Touch the N-Mark of the Bar

Speaker with the BLUETOOTH
device.

3 Make sure that the BLUETOOTH

indicator (blue) lights up.

Connection has been established.

Notes

• You can connect only one device at a
time.

• Depending on your device, you may need
to set the NFC function to on beforehand.
Refer to the operating instructions of your
device.

Tip

• If pairing and the BLUETOOTH co nnection
fail, do the following.
– Relaunch “NFC Easy Connect” and

move the BLUETOOTH device slowly
over the N-Mark.

– Remove the case from the BLUETOOTH

device if using a commercially available
device case.

15

GB

Other Functions

Auto standby function

The system enters standby mode
automatically when you do not operate
the system for about 15 minutes and the
system is not receiving an input signal.

16

GB

Additional Information

Additional Information

Precautions

On safety

• Should any solid object or liquid fall into
the system, unplug the system and have
it checked by qualified personnel before
operating it any further.

• Do not climb on the Bar Speaker and
subwoofer, as you may fall down and
injure yourself, or system damage may
result.

On power sources

• Before operating the system, check that
the operating voltage is identical to your
local power supply. The operating voltage
is indicated on the nameplate on the
bottom of the Bar Speaker.

• If you are not going to use the system for
a long time, be sure to disconnect the
system from the wall outlet (mains). To
disconnect the AC power cord (mains
lead), grasp the plug itself; never pull the
cord.

• One blade of the plug is wider than the
other for the purpose of safety and will fit
into the wall outlet (mains) only one way.
If you are unable to insert the plug fully
into the outlet, contact your dealer.

• AC power cord (mains lead) must be
changed only at a qualified service shop.

On heat buildup

Although the system heats up during
operation, this is not a malfunction.
If you continuously use this system at high
volume, the system temperature at the
rear and bottom rises considerably. To
avoid burning yourself, do not touch the
system.

buildup and prolong the life of the
system.

• Do not place the system near heat
sources or in a place subject to direct
sunlight, excessive dust, or mechanical
shock.

• Do not place anything on the top of the
Bar Speaker.

• If the system is being used in combination
with a TV, VCR, or tape deck, noise may
result and picture quality may suffer. In
such a case, place the system away from
the TV, VCR, or tape deck.

• Use caution when placing the system on a
surface that has been specially treated
(with wax, oil, polish, etc.), as staining or
discoloration of the surface may result.

• Take care to avoid any possible injury
from the corners of the Bar Speaker and
subwoofer.

On operation

Before connecting other equipment, be
sure to turn off and unplug the system.

If you encounter color irregularity
on a nearby TV screen

Color irregularities may be observed on
certain types of TV.

• If color irregularity is observed...
Turn off the TV, then turn it on again after
15 to 30 minutes.

• If color irregularity is observed again...
Place the system further away from the
TV.

On cleaning

Clean the system with a soft, dry cloth. Do
not use any type of abrasive pad, scouring
powder, or solvent such as alcohol or
benzine.

If you have any question or problem
concerning your system, please consult
your nearest Sony dealer.

On placement

• Place the system in a location with
adequate ventilation to prevent heat

GB

17

Troubleshooting

If you experience any of the following
difficulties while using the system, use
this troubleshooting guide to help
remedy the problem before requesting
repairs. Should any problem persist,
consult your nearest Sony dealer.
Be sure to bring both your Bar Speaker
and subwoofer, even if it seems as
though only one has a problem, when
you request to repair.

General

The power does not turn on.

 Check that the AC power cord

(mains lead) is connected securely.

The system does not work normally.

 Disconnect the AC power cord

(mains lead) from the wall outlet
(mains), then reconnect after
several minutes.

Sound

No TV sound is output from the system.

 Press the input button of the jack to

which you connected the TV
(page 11).

 Check the sound output of the TV.

Refer to the operating instructions
of the TV for the TV settings.

 Increase the volume on the TV or

cancel muting.

 If no sound is output from an optical

digital output jack or the TV does
not have an optical digital output
jack, connect the cable box or
satellite box directly to the OPTICAL
jack of the system.

The sound is output from both the
system and the TV.

 Turn off the sound of the TV.

The TV sound from this system lags
behind the image.

 When you are watching movies, you

may hear the sound with a slight
delay from the image.

No sound or only a very low-level
sound of the device connected to the
Bar Speaker is heard from the Bar
Speaker.

 Press the

the remote control and check the
volume level (page 23).

 Press the

(volume)
control to cancel the muting
function (page 23).

 Make sure the input source is

selected correctly. You should try
other input sources by pressing a
different input button on the
remote control (page 11).

 Check that all the cables and cords

of the system and the connected
device are firmly inserted.

No sound or only a very low-level
sound is heard from the subwoofer.

 Press the SW

volume)
control to increase the subwoofer
volume (page 23).

 A subwoofer is for reproducing bass

sound. In the case of input sources
that contain very little bass sound
components (i.e., a TV broadcast),
the sound from the subwoofer may
be difficult to hear.

The surround effect cannot be
obtained.

 Depending on the input signal and

the sound field setting, surround
sound processing may not work
effectively. The surround effect may
be subtle, depending on the
program or disc.

 To play multi channel audio, check

the digital audio output setting on

 (volume) + button on

 (muting) or 

+ button on the remote

 (subwoofer

+ button on the remote

18

GB

Additional Information

the device connected to the syste m.
For details, refer to the operating
instructions supplied with the
connected device.

USB device

The USB device is not recognized.

 Try the following:

 Turn the system off.
 Remove and reconnect the USB

device.

 Turn the system on.

 Make sure that the USB device is

securely connected to the (USB)
port.

 Check if the USB device or a cable is

damaged.

 Check if the USB device is on.
 If the USB device is connected via a

USB hub, disconnect it and connect
the USB device directly to the
system.

 Connect the USB device to the

ANALOG jack of the system using an
analog audio cable (not supplied).

BLUETOOTH device

BLUETOOTH connection cannot be
completed.

 Make sure that the BLUETOOTH

indicator (blue) is lit (page 21).

System status BLUETOOTH

During BLUETOOTH
pairing

The system is attempting
to connect with a
BLUETOOTH device

indicator
(blue)

Flashes quickly

Flashes

System status BLUETOOTH

The system has
established connection
with a BLUETOOTH
device

The system is in
BLUETOOTH standby
mode (when the system
is off)

indicator
(blue)

Lit

Unlit

 Make sure the BLUETOOTH device

to be connected is turned on and
the BLUETOOTH function is
enabled.

 Bring this system and the

BLUETOOTH device closer together.

 Pair this system and the

BLUETOOTH device again. You may
need to cancel the pairing with this
system using your BLUETOOTH
device first.

Pairing cannot be achieved.

 Bring this system and the

BLUETOOTH device closer together.

 Make sure this system is not

receiving interference from a
wireless LAN equipment, other

2.4 GHz wireless devices, or a
microwave oven. If a device that
generates electromagnetic
radiation is nearby, move the device
away from this system.

No sound is output from the connected
BLUETOOTH device.

 Make sure that the BLUETOOTH

indicator (blue) is lit (page 21).

 Bring this system and the

BLUETOOTH device closer together.

 If a device that generates

electromagnetic radiation, such as a
wireless LAN equipment, other
BLUETOOTH devices, or a
microwave oven is nearby, move
the device away from this system.

 Remove any obstacle between this

system and the BLUETOOTH device

19

GB

or move this system away from the
obstacle.

 Reposition the connected

BLUETOOTH device.

 Try changing the wireless frequen cy

of the Wi-Fi router, computer, etc.
to 5 GHz band.

 Increase the volume on the

connected BLUETOOTH device.

The sound is not in sync with the
image.

 When you are watching movies, you

may hear the sound with a slight
delay from the image.

Remote control

The remote control does not function.

 Point the remote control at the

center of the front panel (remote
control sensor) of the system
(page 21).

 Remove any obstacles in the path

between the remote co ntrol and the
system.

 Replace both batteries in the

remote control with new ones, if
they are weak.

 Make sure you are pressing the

correct button on the remote
control (page 23).

of the sensors and remote control
receiver, refer to the operating
instructions supplied with the TV.

Reset

If the system still does not operate
properly, reset the system as follows:

1 Press SW  (subwoofer volume)

+,  (volume) –, and NIGHT in
sequence within 3 seconds.

All 6 indicators on the Bar Speaker
flash once, and the settings return
to their initial status.

2 Disconnect the AC power cord

(mains lead).

Others

Sensors of the TV do not work properly.

 The Bar Speaker may block some

sensors (such as the brightness
sensor) and the remote control
receiver of your TV, or the “emitter
for 3D glasses (infrared
transmission)” of a 3D TV that
supports the infrared 3D glass
system or the wireless
communication. Move the Bar
Speaker away from the TV within a
range that allow those parts to
operate properly. For the locations

GB

20

Additional Information

Guide to parts and controls

For more information, refer to the pages indicated in parentheses.

Bar Speaker

Top, front, and side panels

 OPTICAL indicator (page 11)
 ANALOG indicator (page 11)
 USB indicator (page 11)
 BLUETOOTH indicator (blue)

BLUETOOTH status

– During BLUETOOTH pairing:

Flashes quickly

– BLUETOOTH connection is being

attempted: Flashes

– BLUETOOTH connection has been

established: Lit

– BLUETOOTH standby mode (when

the system is off): Unlit

 SURROUND indicator (page 13)
 CLEARAUDIO+ indicator

(page 13)

 N-Mark (page 15)

When using the NFC function,
touch your NFC-compatible
device to the mark.

 Remote control sensor
 / (on/standby) button

Turns on the system, or sets it to
standby mode.

 INPUT button (page 11)
 PAIRING button (page 14)
 VOL (volume) +/– buttons
 (USB) port (page 12)

GB

21

Rear panel

 Subwoofer jack
 ANALOG jack

 OPTICAL jack
 AC power cord (mains lead)

22

GB

Additional Information

Remote control

 (volume) +*/– buttons

Adjusts the volume.

 SW  (subwoofer volume) +/–

buttons

Adjusts the volume of bass
sound.

 (muting) button

Turns off the sound temporarily.

 CLEARAUDIO+ button

Automatically selects the suitable
sound setting for the sound
source.

 SURROUND button (page 13)
 VOICE button (page 13)

* (play/pause) button



Pauses or resumes playback.

 NIGHT button (page 13)
/ (previous/next)

buttons

To go to the beginning of the
previous or next file.

*The AUDIO,  and  + buttons have

a tactile dot. Use it as a guide during
operation.

 AUDIO* button (page 13)
/ (on/standby) button

 (BLUETOOTH) button

(page 11)

  (select) buttons
 USB button (page 11)
 ANALOG button (page 11)
 OPTICAL button (page 11)

23

GB

Playable types of files

Supported audio formats

Codec Extension

MP3 (MPEG-1 Audio
Layer III)

AAC .m4a
WMA9 Standard .wma

Notes

• Some files edited on a PC may not play.

• The system does not play coded files such
as DRM and Lossless.

• The system can recognize the following
files or folders in USB devices:
– up to 200 folders
– up to 150 files/folders in a single layer

• Some USB devices may not work with this
system.

• The system can recognize Mass Storage
Class (MSC) devices.

.mp3

Audio formats supported by this system
are as follows.

•Dolby Digital

•Linear PCM 2ch 48kHz or less

24

GB

Additional Information

Specifications

Bar Speaker (SA-CT80)

Amplifier section

POWER OUTPUT (rated)

Front L + Front R:
12 W + 12 W (at 4 ohms, 1 kHz, 1% THD)

POWER OUTPUT (reference)

Front L/Front R:
20 W (per channel at 4 ohms, 1 kHz)

Subwoofer amplifier section

POWER OUTPUT (reference)

40 W (at 8 ohms, 100 Hz)

Inputs

OPTICAL
ANALOG

USB Section

(USB) port

Type A

BLUETOOTH section

Communication system

BLUETOOTH Specification version 4.0

Output

BLUETOOTH Specification Power Class
2

Maximum communication range

Line of sight approx. 10 m

Maximum number of devices to be

registered
8 devices

Frequency band

2.4 GHz band (2.4000 GHz -

2.4835 GHz)

Modulation method

FHSS (Freq Hopping Spread Spectrum)

Compatible BLUETOOTH profiles

A2DP (Advanced Audio Distribution
Profile)

Supported Codecs

4)

SBC

Transmission range (A2DP)

20 Hz - 20,000 Hz (Sampling frequency

44.1 kHz)

1)

The actual range will vary depending on
factors such as obstacles between
devices, magnetic fields around a

3)

microwave oven, static electricity,
cordless phone, reception sensitivity,
operating system, software application,
etc.

2)

BLUETOOTH standard profiles indicate
the purpose of BLUETOOTH
communication between devices.

3)

Codec: Audio signal compression and
conversion format

4)

Subband Codec

Speakers

Front L/Front R speaker section

Speaker system

2-way speaker system, Acoustic
suspension

Speaker

Tweeter: 14 mm - 25 mm balance
dome type
Woofer: 35 mm × 120 mm cone type

General

Power requirements

220 V - 240 V AC, 50 Hz/60 Hz

Power consumption

On: 21 W
Standby mode: 0.5 W or less

Dimensions (approx.) (w/h/d)

901 mm × 52 mm × 84 mm

Mass (approx.)

2kg

1)

Subwoofer (SS-WCT80)

Speaker system

Subwoofer system, Bass reflex

Speaker

130 mm cone type

Dimensions (approx.) (w/h/d)

170 mm × 245 mm × 300 mm

2)

Mass (approx.)

2.7 kg

Design and specifications are subject to
change without notice.

25

GB

On BLUETOOTH communication

• BLUETOOTH devices should be used

within approximately 10 meters
(unobstructed distance) of each other.
The effective communication range
may become shorter under the
following conditions.
– When a person, metal object, wall or

other obstruction is between the
devices with a BLUETOOTH
connection

– Locations where a wireless LAN is

installed

– Around microwave ovens that are in

use

– Locations where other

electromagnetic waves occur

• BLUETOOTH devices and wireless LAN

(IEEE 802.11b/g) use the same
frequency band (2.4 GHz). When using
your BLUETOOTH device near a device
with wireless LAN capability,
electromagnetic interference may
occur. This could result in lower data
transfer rates, noise, or inability to
connect. If this happens, try the
following remedies:
– Use this system at least 10 meters

away from the wireless LAN device.

– Turn off the power to the wireless

LAN device when using your
BLUETOOTH device within 10 meters.

– Install this system and BLUETOOTH

device as closer to each other as
possible.

• The radio waves broadcast by this

system may interfere with the
operation of some medical devices.
Since this interference may result in
malfunction, always turn off the po wer
on this system and BLUET OOTH device
in the following locations:

– In h ospitals, on trains, in airpl anes, at

gas stations, and any place where
flammable gasses may be present

– Near automatic doors or fire alarms

• This system supports security
functions that comply with the
BLUETOOTH specification to ensure
secure connection during
communication using BLUETOOTH
technology. However, this security
may be insufficient depending on the
setting contents and other factors, so
always be careful when performing
communication using BLUETOOTH
technology.

• Sony cannot be held liable in any way
for damages or other loss resulting
from information leaks during
communication using BLUETOOTH
technology.

• BLUETOOTH communication is not
necessarily guaranteed with all
BLUETOOTH devices that have the
same profile as this system.

• BLUETOOTH devices connected with
this system must comply with the
BLUETOOTH specification prescribed
by the Bluetooth SI G, Inc., and must be
certified to comply. However, even
when a device complies with the
BLUETOOTH specification, there may
be cases where the characteristics or
specifications of the BLUETOOTH
device make it impossible to connect,
or may result in different control
methods, display or operation.

• Noise may occur or the audio may cut
off depending on the BLUETOOTH
device connected with this system,
the communications environment, or
surrounding conditions.

If you have any questions or problems
concerning your system, please consult
your nearest Sony dealer.

26

GB

Additional Information

27

GB

警告

切勿將本設備安裝在狹窄的空間內，如書
櫃或壁櫥內。

為了降低發生火災的危險，請勿使用報
紙、桌布、窗簾等物品蓋住設備的通風
孔。
請勿將如點燃的蠟燭等明火源放置於設備
上。

為了降低發生火災或觸電的危險，請勿讓
本設備受到液體潑濺，也不要將如花瓶等
裝滿液體的物體放置於本設備上。

只要本機的電源線仍連接在電源插座上，
即使本機的電源已經關閉，但本機仍然未
與交流電源斷開連接。

由於電源插頭是用來斷開本機與電源插座
的連接，因此請將本機連接至便於插拔的
交流電源插座。一旦發現本機有異常情
況，請立即斷開電源插頭與交流電源插座
的連接。

請勿讓電池或安裝電池的設備暴露在過熱
的環境中，例如：陽光、火等。

限室內使用。

主動式揚聲器系統

標示牌標示在底部。

N字標示為NFC Forum, Inc.在美國和其他
國家的商標或註冊商標。

TM

Android

“ClearAudio+” 是 Sony Corporation 的
商標。

MPEG Layer-3 音頻編碼技術和專利由
Fraunhofer IIS 和 Thomson 授權。

Windows Media 是 Microsoft
Corporation 在美國和 / 或其它國家的註
冊商標或商標。
本產品由 Microsoft Corporation 的某些
知識產權所保護。在沒有獲得 Microsoft
或授權 Microsoft 子公司許可的情況下，
不允許於本產品之外使用或配銷此技術。

其他商標和商標名稱為其各自所有人擁
有。

為 Google Inc. 的商標。

版權與商標

*

本系統採用 Dolby
System。

* Dolby Laboratories 授權製造。

Dolby 和雙 D 標誌是 Dolby
Laboratories 的商標。

BLUETOOTH® 字型商標和圖形商標均字型商
標和圖形商標均為 Bluetooth SIG, Inc.
所有之註冊商標，Sony Corporation 對該
商標的各項使用均已經授權。

CT

2

Digital Surround

關於這些使用說明書

•本使用說明書內的指示解説遙控器的控
制。如果主要裝置上的功能名稱與遙控
器上的功能名稱相同或類似，您也可以
使用主要裝置上的控制功能。

•有些圖解為概念圖，可能與實際產品不
同。

CT

CT

3

目錄

關於這些使用說明書 .......... 3

開始使用

包裝內容物 ..................5

連接 TV 與重低音揚聲器 ....... 6

安置系統 .................... 8

將主動式揚聲器系統安裝到牆上

.......................... 9

開啟系統 ................... 10

聆聽

聆聽 TV、有線 / 衛星電視盒等聲音

........................ 11

從 USB 裝置聆聽音樂 ......... 12

從 BLUETOOTH 裝置聆聽音樂 ... 12

聲音調整

享受音效 ................... 13

BLUETOOTH 功能

從 BLUETOOTH 裝置聆聽音樂 ... 14

其他功能

自動待機功能 ...............16

其他資訊

注意事項 ...................17

疑難排除 ...................17

零件與控制功能指南 .........20

可播放的檔案類型 ...........23

支援的音訊格式 .............23

規格 .......................24

在 BLUETOOTH 通訊時 .........25

CT

4

開始使用

開始使用

包裝內容物

主動式揚聲器系統 （1）

重低音揚聲器 （1）

數位光纖纜線 （1）

R03 （AAA 型）電池 （2）

設定遙控器

遙控器 （1）

CT

5

連接 TV 與重低音揚聲器

TV、有線電視盒或衛星電視盒

數位光纖纜線 （提供）

重低音揚聲器

您的 TV 上有數位光纖插孔時

註

• 僅能連接提供的 SS- WCT80 重低音揚聲器。請勿連接任何其他的重低音揚聲器。

CT

6

開始使用

您的 TV 上沒有數位光纖插孔時

TV、有線電視盒或衛星電視盒

類比音源線 （未提供）

重低音揚聲器

註

• 僅能連接提供的 SS- WCT80 重低音揚聲器。請勿連接任何其他的重低音揚聲器。

• 如果 TV 的耳機插孔也做為音訊輸出插孔，請檢查 TV 的音訊輸出設定。詳細資訊，請參閱 TV 的

使用說明書。

7

CT

安置系統

主動式揚聲器系統

重低音揚聲器

10 cm

以下圖解示範系統安裝方式。

註

• 放置主動式揚聲器系統時請勿遮住上方面
板。

安裝到架子上

安裝到牆上

請參閱 “ 將主動式揚聲器系統安裝到牆
上” (第9頁)。

重低音揚聲器安裝注意事項

放置重低音揚聲器時，後方面板請與牆面
相距至少 10 cm。

CT

8

開始使用

將主動式揚聲器系統安

4 mm

大於 30 mm

4.6 mm

按住主動式揚聲器系統的背面

9 mm

9mm至
10 mm

447 mm

裝到牆上

您可將主動式揚聲器系統安裝到牆上。

註

• 準備適合牆面材料和強度的螺絲 （未提
供）。由於石膏板牆壁易碎，請將兩個螺栓
牢固釘入牆柱。水平安裝主動式揚聲器系
統，懸掛在連續平面牆柱上的螺絲。

• 請務必將安裝工程分包給Sony經銷商或授權
承包商，並在安裝期間特別注意安全事宜。

• 對若因安裝錯誤、牆壁不夠堅固，或螺絲安
裝錯誤、自然災害等引起的事故或損壞，
Sony 概不負責。

1 準備適用於主動式揚聲器系統背面孔

的螺絲 （未提供）。

2 將兩個螺栓擰入牆壁中的牆柱。

螺絲須突出 9 mm 至 10 mm。

3 將主動式揚聲器系統掛到螺絲上。

將主動式揚聲器系統背面的洞孔對齊
螺絲，然後將主動式揚聲器系統掛到
兩個螺絲上。

CT

9

開啟系統

/

（開 / 待機）

1 接上交流電源線。

2 按下 / （開 / 待機）按鈕。

輸入指示燈亮起。

10

CT

聆聽

聆聽

OPTICAL

 （音量）

+/-

聆聽 TV、有線 / 衛星 電視盒等聲音

1 按下與聆聽裝置連接之插孔的輸入按

鈕。
所選裝置的指示燈亮起。

OPTICAL 按鈕
連接到 OPTICAL 插孔的 TV

ANALOG 按鈕
連接到 ANALOG 插孔的類比裝置

USB 按鈕

連接到 （USB）插孔的 USB 裝置
(第12頁)

（BLUETOOTH）按鈕

支援 A2DP 的 BLUETOOTH 裝置

2 按下  （音量）+/– 調整音量。

提示

• 如果您按下主動式揚聲器系統上的 INPUT，
裝置會循環變更，如下所示。
OPTICAL  ANALOG  USB  BLUETOOTH

11

CT

從 USB 裝置聆聽音樂

您可播放連接的 USB 裝置上的音樂檔。
如需可播放的檔案類型，請參閱 “ 可播
放的檔案類型 ” ( 第 23 頁 )。

1 將 USB 裝置連接至 （USB）插孔。

2 按下 USB。
3 按下  （播放/暫停）。
4 按下   選擇要播放的資料夾。

註

• 先關閉系統，再移除 USB 裝置，以免資料毀
損或使 USB 裝置損壞。

從 BLUETOOTH 裝置聆聽 音樂

請參閱 “BLUETOOTH 功能 ” ( 第 14 頁 )。

12

CT

聲音調整

聲音調整

設定聲音模式

聲音模式可讓對話更清楚。

享受音效

若要設定音效，請按下遙控器上的其中一
個音效按鈕。

選擇音效

播放期間重複按下 SURROUND。
音效會如下所示循環變更。
CLEARAUDIO+
SURROUND 關閉

CLEARAUDIO+
根據音源自動選擇適合的聲音設定。
CLEARAUDIO+ 指示燈亮起。

SURROUND 開啟
以環繞音效播放聲音。SURROUND 指示燈亮起。

SURROUND 關閉
輸入音源已音路混合為 2 聲道。CLEARAUDIO+
與 SURROUND 指示燈熄滅。

設定夜晚模式

播放以音效與清楚的對話增強的聲音。

按下 NIGHT。
ANALOG 指示燈閃爍兩次。
若要停用夜晚模式，請再按一下 NIGHT。
OPTICAL 指示燈閃爍兩次。

 SURROUND 開啟 

按下 VOICE。
ANALOG 指示燈閃爍兩次。
若要停用聲音模式，請再按一下 VOICE。
OPTICAL 指示燈閃爍兩次。

選擇多工廣播聲音 （雙語單聲
道）

系統收到 Dolby Digital 多工廣播訊號
時，您可以享受多工廣播聲音。

重複按下 AUDIO。
聲道會循環變更，如下所示。

 副聲道  主聲道 / 副聲道

主聲道

主聲道
僅輸出主聲道。OPTICAL 指示燈閃爍兩次。

副聲道
僅輸出副聲道。ANALOG 指示燈閃爍兩次。

主聲道 / 副聲道
左側揚聲器輸出主聲道，右側揚聲器輸出副聲
道。USB 指示燈閃爍兩次。

13

CT

設定 Dolby DRC （動態範圍控
制）

適用於以低音量觀賞電影。DRC 適用於
Dolby Digital 來源。

按住 AUDIO 5 秒，然後按住 VOICE 5 秒，
即可開啟或關閉 Dolby DRC。

開啟
根據內容所含的資訊壓縮聲音。ANALOG 指示燈
閃爍兩次。

關閉
未壓縮的聲音。OPTICAL 指示燈閃爍兩次。

BLUETOOTH 功能

從 BLUETOOTH 裝置聆聽 音樂

將此系統與 BLUETOOTH 裝置配
對

配對是在 BLUETOOTH 裝置之間建立連結以
允許無線連線的必要程序。您必須先將裝
置與系統配對，才能開始使用系統。
BLUETOOTH 裝置一旦配對後，便不需要再
次配對。

1 按下主動式揚聲器系統上的PAIRING。

進行 BLUETOOTH 配對時，BLUETOOTH
指示燈 （藍色）會快速閃爍。

2 開啟 BLUETOOTH 裝置上的BLUETOOTH 功

能，搜尋裝置並選擇 “HT- CT80”。
如需密碼金鑰，請輸入 “0000”。

3 確定 BLUETOOTH 指示燈 （藍色）亮

起。
已建立連線。

註

• 您最多可以配對 8個BLUETOOTH 裝置。如
果要配對第9個BLUETOOTH 裝置，則新
的裝置會取代最早連接的裝置。

14

CT

BLUETOOTH 功能

聆聽已登記裝置的音樂

1 按下 （BLUETOOTH）。
2 在 BLUETOOTH 裝置上選擇

“HT- CT80”。

3 確定 BLUETOOTH 指示燈 （藍色）亮

起。

4 開始在 BLUETOOTH 裝置上播放。

註

• 若系統具有配對資訊，則即使系統關機時也
會處於 BLUETOOTH 待機模式。

以觸控功能 （NFC）連線至
BLUETOOTH 裝置

將 NFC 相容的 BLUETOOTH 裝置拿到系統的
N 字標示附近，系統與 BLUETOOTH 裝置會
繼續完成配對，BLUETOOTH 連線會自動進
行。

相容的裝置
內建 NFC 功能的智慧型手機、平板電腦
與音樂播放器 （作業系統：Android

2.3.3 或更新版本，不包括 Android

3.x）

1 下載、安裝並啟動 “NFC 快速連線 ”

應用程式。

2 以 BLUETOOTH 裝置觸碰主動式揚聲器

系統的N字標示。

3 確定 BLUETOOTH 指示燈 （藍色）亮

起。
已建立連線。

註

• 您一次只能與一個裝置連線。

• 視您的裝置而定，您可能需要事先設定 NFC

功能。請參閱裝置的使用說明書。

提示

• 如果配對與 BLUETOOTH 連線失敗，請執行下
列步驟。
–重新啟動 “NFC 快速連線 ” 並將

BLUETOOTH 裝置慢慢地移動至 N 字標示上
方。

–如果有使用市售的裝置外殼，請將外殼從

BLUETOOTH 裝置上拆下。

註

• 在某些國家或地區可能無法下載此應用
程式。

• 視您的 BLUETOOTH 裝置而定，您可能不
需要此操作。

15

CT

其他功能

自動待機功能

當您未操作系統約 15 分鐘且系統未收到
輸入訊號時，系統會自動進入待機模式。

16

CT

其他資訊

其他資訊

注意事項

• 請小心不要讓主動式揚聲器系統和重低音揚
聲器的邊緣受損。

關於操作

連接其他設備前，請務必關閉系統並拔掉電
源插頭。

關於安全

• 若有任何固體或液體進入本系統，請拔下本
系統的電源插頭，並經合格的專業人員檢查
以後，方可繼續使用。

• 請勿攀爬主動式揚聲器系統和重低音揚聲
器，否則可能跌落受傷，或是損壞系統。

關於電源

• 操作系統前，請先確定操作電壓與當地電源
供應相符。操作電壓如主動式揚聲器系統底
部的名牌所示。

• 如果您準備長時間不使用系統，務必中斷系
統與牆壁電源插座的連接。若要將交流電源
線拔掉，請抓住插頭，切勿拉扯電源線。

• 為了安全起見，電源插頭的一個插腳會比另
一個插腳寬，而且只能以一個方向插入牆壁
電源插座。如您無法將插頭完全插入插座
內，請洽詢您的經銷商。

• 僅能在合格的維修商店更換交流電源線。

關於熱量累積

本系統的熱度會在操作過程中累積，這並非
故障。
如果持續長時間以高音量使用本系統，系統
的背部和底部的溫度會變得相當高。為了避
免燙傷，請勿觸碰系統。

關於擺放

• 請將系統擺放在通風良好的位置以防止熱量
累積，並延長系統的壽命。

• 請勿將系統擺放於靠近熱源的地方，或者會
受到陽光直曬、灰塵過多或機械性撞擊的地
方。

• 請勿將任何物品放在主動式揚聲器系統上
方。

• 若本系統與 TV、錄影機或磁帶卡座搭配使
用，可能會產生雜訊，影響影像品質。發生
此狀況時，請將系統設置在距離 TV、錄影
機或磁帶卡座較遠處。

• 將本系統置於經特別處理 （打蠟、塗油、
拋光等）的表面上時，請務必小心，否則可
能會造成地板著色或變色。

如果附近的 TV 螢幕上出現色彩不均
勻

某些類型的 TV 可能會出現色彩不均勻的情
況。

• 如果出現色彩不均勻 ...
請關閉 TV，在 15 至 30 分鐘後再次開啟。

• 如果再次出現色彩不均勻 ...
請將系統設置在距離 TV 較遠處。

關於清潔

使用柔軟的乾布清潔系統。請勿使用任何類
型的砂紙、拋光粉或溶液 （如酒精、汽油
等）。

如果對本系統有任何疑問或問題，請就近與
Sony 經銷商聯絡。

疑難排除

在使用本系統時，如遇到以下任何疑難問
題，在要求維修前先使用疑難排除指南幫
助解決故障。如果無法解決問題，請就近
與 Sony 經銷商聯絡。
在要求進行維修時，請務必同時攜帶您的
主動式揚聲器系統和重低音揚聲器，即使
看起來只有一個有問題。

一般

電源未開啟。
 檢查交流電源線是否連接牢固。

系統未正常運作。
 將交流電源線從牆壁電源插座中拔

出，數分鐘後再重新接上。

17

CT

音效

系統無法輸出 TV 的聲音。
 按下與 TV 連接之插孔的輸入按鈕 ( 第

11 頁 )。

 檢查 TV 的聲音輸出。TV 設定值，請參

閱 TV 的使用說明書。

 提高 TV 音量或取消靜音。
 如果沒有聲音從數位光纖輸出插孔輸

出，或 TV 沒有數位光纖輸出插孔，
請將有線電視盒或衛星電視盒直接連
接系統的 OPTICAL 插孔。

系統與 TV 會同時輸出聲音。
 關閉 TV 的聲音。

本系統的 TV 聲音延遲，跟不上影像。
 觀賞電影時，您可能會聽到影像聲音

發生輕微延遲。

連接至主動式揚聲器系統的裝置無法從主
動式揚聲器系統發出聲音，或聲音很小。
 按下遙控器上的

並檢查音量(第22頁)。

 按下遙控器上的

（音量）+ 按鈕可取消靜音功能 ( 第

22 頁 )。

 確認已正確選擇輸入來源。您應該按

下遙控器上的不同輸入按鈕來嘗試其
他輸入來源(第11頁)。

 檢查系統與連接裝置的所有電纜與導

線是否皆已完全插牢。

重低音揚聲器無法發出聲音，或聲音很
小。
 按下遙控器上的 SW

器音量）+ 按鈕可調高重低音揚聲器
音量(第22頁)。

 重低音揚聲器可以產生低音。若輸入

來源包含的低音聲音元件很少 （也就
是TV轉播），則可能會難以聽見重低
音揚聲器的聲音。

不能產生環繞效果。
 視輸入訊號與音場設定而定，環繞聲

處理可能無法有效運作。環繞音效可
能不明顯，視節目或光碟而定。

 若要播放多聲道音訊，請檢查連接本

系統的裝置上，數位音訊的輸出設定

 （音量）+ 按鈕，

 （靜音）或 

 （重低音揚聲

是否正確。詳細資訊，請參閱連接裝
置提供的使用說明書。

USB 裝置

USB 裝置無法辨識。

 請嘗試以下步驟：

 關閉系統。
 移除 USB 裝置，然後再重新連接。
 開啟系統。

 確定 USB 裝置已牢固連接至 （USB）

插孔。

 檢查 USB 裝置或纜線是否損壞。
 檢查 USB 裝置是否開啟。
 如果 USB 裝置係透過 USB 集線器連接，

請將其拔出，然後將 USB 裝置直接連
接至系統。

 使用類比音源線 （未提供）將 USB 裝

置連接至系統的 ANALOG 插孔。

BLUETOOTH 裝置

無法完成 BLUETOOTH 連線。
 確定 BLUETOOTH 指示燈 （藍色）亮起

(第20頁)。

系統狀態 BLUETOOTH 指示

BLUETOOTH 配對時 快速閃爍
系統正在嘗試與

BLUETOOTH 裝置連線
系統已與 BLUETOOTH 裝置

建立連線
系統處於 BLUETOOTH 待機

模式 （系統關閉時）

 確認要連接的BLUETOOTH 裝置已開啟，

並已啟用 BLUETOOTH 功能。

 讓本系統與BLUETOOTH 裝置互相靠近。
 重新配對本系統與 BLUETOOTH 裝置。

您可能需要先使用 BLUETOOTH 裝置取
消與本系統的配對。

無法完成配對。

 讓本系統與BLUETOOTH 裝置互相靠近。
 確認本系統未接收來自無線區域網路

設備、其他 2.4 GHz 無線裝置或微波

燈 （藍色）

閃爍

發亮

未亮燈

18

CT

其他資訊

爐的干擾。如果附近有產生電磁輻射
的裝置，請將該裝置移開本系統。

連接的 BLUETOOTH 裝置無法輸出聲音。
 確定 BLUETOOTH 指示燈 （藍色）亮起

(第20頁)。

 讓本系統與BLUETOOTH 裝置互相靠近。
 如果附近有產生電磁輻射的裝置，如

無線區域網路設備、其他 BLUETOOTH
裝置或微波爐，請將該裝置移開本系
統。

 請將本系統與 BLUETOOTH 裝置之間的

任何障礙物移開，或將本系統遠離障
礙物。

 重新擺放連接的 BLUETOOTH 裝置。
 嘗試將 Wi-Fi 路由器、電腦等裝置的

無線頻率變更為 5 GHz 波段。

 調高連接的 BLUETOOTH 裝置的音量。

聲音未和影像同步。
 觀賞電影時，您可能會聽到影像聲音

發生輕微延遲。

遙控器

遙控器無法使用。
 將遙控器指向系統前方面板的中心

（遙控器感應器）( 第 20 頁 )。

 移除遙控器和系統之間的所有障礙

物。

 若遙控器的電池電量不足，請更換兩

顆新電池。

 確認您在遙控器上按下正確按鈕 ( 第

22頁)。

重設

若系統仍無法正確運作，請依以下方法重
設系統：

1 在 3 秒內依序按下 SW （重低音揚聲

器音量）+、  （音量）– 和
NIGHT。

主動式揚聲器系統上的 6 個指示燈全
部閃爍 1 次，且設定回復成初始狀
態。

2 拔掉交流電源線。

其他

TV 感應器未正確運作。
 主動式揚聲器系統可能會封鎖某些感

應器 （例如亮度感應器）和 TV 的遙
控接收器，或者支援紅外線 3D 眼鏡
系統或無線通訊之 3D TV 的 “3D 眼鏡
發射器 （紅外線傳輸）”。在允許部
件正確運作的範圍內，將主動式揚聲
器系統從 TV 處移開。針對感應器和
遙控接收器的位置，請參閱 TV 隨附
的使用說明書。

19

CT

零件與控制功能指南

如需詳細資訊，請參閱括號中註明的頁面。

主動式揚聲器系統

上方、前方與側面面板

 OPTICAL 指示燈 ( 第 11 頁 )
 ANALOG指示燈(第11頁)
 USB指示燈(第11頁)
 BLUETOOTH 指示燈 （藍色）

BLUETOOTH 狀態

–BLUETOOTH 配對時：快速閃爍
–正在嘗試建立 BLUETOOTH 連線：閃

爍
–已建立 BLUETOOTH 連線：發亮
–BLUETOOTH 待機模式 （系統關閉

時）：未亮燈

 SURROUND 指示燈 ( 第 13 頁 )
 CLEARAUDIO+指示燈(第13頁)
 N字標示(第15頁)

使用 NFC 功能時，請將 NFC 相容的
裝置觸碰該標示。

 遙控器感應器
/ （開 / 待機）按鈕

開啟系統，或將系統設定為待機模
式。

CT

20

 INPUT按鈕(第11頁)
 PAIRING 按鈕 ( 第 14 頁 )
 VOL （音量）+/– 按鈕
 （USB）插孔(第12頁)

其他資訊

後方面板

 重低音揚聲器插孔
 ANALOG 插孔

 OPTICAL 插孔
 交流電源線

21

CT

遙控器

 SW  （重低音揚聲器音量）+/–

按鈕
調整低音音量。

（靜音）按鈕

暫時關閉聲音。

 CLEARAUDIO+ 按鈕

自動為音源選擇適合的聲音設定。

 SURROUND按鈕(第13頁)
 VOICE按鈕(第13頁)


*



（播放 / 暫停）按鈕

暫停或繼續播放。

 NIGHT按鈕(第13頁)
/（上一首 / 下一首）按鈕

跳至上一個或下一個檔案的開頭。

*

AUDIO、 和  + 按鈕有觸點。在操作
期間可用來當做指引。

 AUDIO*按鈕 ( 第 13 頁 )
/ （開 / 待機）按鈕

 （BLUETOOTH）按鈕 ( 第 11 頁 )
  （選擇）按鈕

 USB按鈕(第11頁)
 ANALOG 按鈕 ( 第 11 頁 )
 OPTICAL 按鈕 ( 第 11 頁 )
（音量）+

*

/– 按鈕

調整音量。

CT

22

其他資訊

可播放的檔案類型

支援的音訊格式

轉碼器 副檔名
MP3 （MPEG-1 Audio

Layer III）
AAC .m4a
WMA9 標準 .wma

註

• 有些經過 PC 編輯的檔案可能無法播放。

• 系統無法播放經過編碼的檔案，如 DRM 和

Lossless。

• 系統可辨識 USB 裝置中的以下檔案或資料
夾：
–最多 200 個資料夾
–單層最多 150 個檔案 / 資料夾

• 有些 USB 裝置可能不適用於本系統。

• 系統可識別大容量存儲器級別 （MSC）裝

置。

.mp3

本系統支援的音訊格式如下所示。

• Dolby Digital

• Linear PCM 2ch 48 kHz 或以下

23

CT

規格

主動式揚聲器系統 （SA- CT80）

擴大機部分

功率輸出 （額定）

左前 + 右前：
12 W + 12 W（4 ohms，1 kHz，1% THD）

功率輸出 （參考）

左前 / 右前：
20 W （每聲道 4 ohms，1 kHz）

重低音揚聲器擴大機部分

功率輸出 （參考）

40 W （8 ohms，100 Hz）

輸入

OPTICAL
ANALOG

USB 部分

（USB）插孔

Type A

BLUETOOTH 部分

通訊系統

BLUETOOTH 規格 4.0 版

輸出

BLUETOOTH 規格電源等級 2

最長的通訊範圍

視線範圍約 10 m

可登記的裝置數量上限

8個裝置

頻帶

2.4 GHz 頻帶 （2.4000 GHz -

2.4835 GHz）

調變方式

FHSS（Freq Hopping Spread Spectrum）

相容的 BLUETOOTH 設定檔

A2DP （Advanced Audio Distribution
Profile）

支援的轉碼器

4)

SBC

傳輸範圍 （A2DP）

20 Hz - 20000 Hz（取樣頻率 44.1 kHz）

1)

實際範圍視裝置之間的障礙物、微波爐附
近的磁場、靜電、無線電話、接收穩定性、
作業系統、應用軟體等因素而異。

2)

BLUETOOTH 標準規範指示裝置之間的
BLUETOOTH 通訊目的。

3)

轉碼器：音訊訊號壓縮與轉換格式

4)

子帶轉碼器

1)

2)

3)

揚聲器

左前置 / 右前置揚聲器部分

揚聲器系統

雙向揚聲器系統、聲學避震

揚聲器

高音揚聲器：14 mm - 25 mm 平衡圓頂型
低音揚聲器：35 mm × 120 mm 圓錐型

一般

電源需求

220 V - 240 V AC，50 Hz/60 Hz

耗電量

開啟：21 W
待機模式：0.5 W 或以下

尺寸（約）（寬/高/深）

901 mm × 52 mm × 84 mm

總重量 （約）

2kg

重低音揚聲器 （SS- WCT80）

揚聲器系統

重低音揚聲器系統，低音反射

揚聲器

130 mm 圓錐型

尺寸（約）（寬/高/深）

170 mm × 245 mm × 300 mm

總重量 （約）

2.7 kg

設計和規格如有變更，恕不另行通知。

24

CT

其他資訊

在 BLUETOOTH 通訊時

• BLUETOOTH裝置必須在距離彼此約10公尺
（無障礙）範圍內才能使用。有效通訊

範圍可能會因以下條件而更短。
–以 BLUETOOTH 連線的裝置之間有人、

金屬物、牆或其他障礙物
–裝有無線區域網路的地點
–在使用中的微波爐附近
–有其他電磁波的地點

• BLUETOOTH 裝置與無線區域網路 （IEEE

802.11b/g）皆使用同一個頻帶

（2.4 GHz）。在具無線區域網路功能的

裝置附近使用 BLUETOOTH 裝置時，可能
會發生電磁干擾。此時可能導致資料傳
輸率降低、雜訊，或無法連線。若發生
此情況，請嘗試以下解決辦法：
–在距離無線區域網路裝置至少 10 公尺

遠的位置使用本系統。
–在 10 公尺範圍內使用 BLUETOOTH 裝置

時，請關閉無線區域網路裝置的電

源。
–安裝本系統與 BLUETOOTH 裝置時儘可

能彼此靠近。

• 本系統的無線電波廣播可能會干擾某些
醫療裝置的運作。由於此種干擾可能會
導致故障，在以下地點請務必關閉本系
統與 BLUETOOTH 裝置的電源：
–醫院、火車、飛機、加油站，以及任

何可能會出現易燃氣體的地方

–自動門或火災警報器附近

• 本系統支援符合BLUETOOTH規格的安全性
功能，以確保使用 BLUETOOTH 技術通訊
時的安全性。然而視設定內容與其他因
素而定，安全性可能不足，因此使用
BLUETOOTH 技術通訊時請務必小心。

• Sony對於使用BLUETOOTH技術進行通訊期
間，因資訊外洩導致的任何損壞或其他
損失概不負責。

• 即使所有BLUETOOTH裝置的設定檔與本系
統相同，我們仍不保證可進行
BLUETOOTH 通訊。

• 與本系統連接的BLUETOOTH裝置必須符合
Bluetooth SIG, Inc. 指定的 BLUETOOTH
規格，並須經過認證。但是，即使裝置
符合 BLUETOOTH 規格，仍有可能因
BLUETOOTH 裝置的特性或規格而無法連

線，或需要以其他方法控制、顯示或操
作。

• 視連線至本系統的 BLUETOOTH 裝置、通訊
環境或周遭條件而定，可能會出現雜訊
或音訊中斷的情況。

如果您對本系統有任何疑問或問題，請就
近與 Sony 經銷商聯絡。

25

CT

©2015 Sony Corporation Printed in China 4-567-473-81(2)