Sony HSRX-200 Service manual

DIGITAL SURVEILLANCE RECORDER

HSR-X200
HSR-X200P

SERVICE MANUAL

Volume 1 1st Edition (Revised 1)

! WARNING

This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.

! WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.

! AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.

HSR-X200/X200P

CAUTION

ADVARSEL

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.

Vorsicht!

Explosionsgefahr bei unsachgemäßem Austausch

der Batterie.

Ersatz nur durch denselben oder einen vom

Hersteller empfohlenen ähnlichen Typ. Entsorgung

gebrauchter Batterien nach Angaben des

Herstellers.

ATTENTION

Il y a danger d’explosion s’il y a remplacement

incorrect de la batterie.

Remplacer uniquement avec une batterie du même

type ou d’un type équivalent recommandé par le

constructeur.

Mettre au rebut les batteries usagées conformément

aux instructions du fabricant.

Lithiumbatteri - Eksplosjonsfare.

Ved utskifting benyttes kun batteri som

anbefalt av apparatfabrikanten.

Brukt batteri returneres

apparatleverandøren.

VARNING

Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en likvärdig typ

som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt gällande

föreskrifter.

VAROITUS

Paristo voi räjähtää jos se on virheellisesti

asennettu.

Vaihda paristo ainoastaan laitevalmistajan

suosittelemaan tyyppiin.

Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

Lithiumbatteri-Eksplosionsfare ved fejlagtig

Levér det brugte batteri tilbage til leverandøren.

HSR-X200/X200P

ADVARSEL!

håndtering.

Udskiftning må kun ske med batteri

af samme fabrikat og type.

Attention-when the product is installed in Rack:

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.

2. Providing protective earth

When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.

4. Prevention against achieving hazardous
condition due to uneven mechanical loading

When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.

5. Install the equipment while taking the operating
temperature of the equipment into consideration

For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.

For the customers in the Netherlands
Voor de klanten in Nederland

Dit apparaat bevat een (CF)

n-Li batterij voor memory

back-up.

Raadpleeg uw leverancier over de verwijdering van de
batterij op het moment dat u het apparaat bij einde
levensduur afdankt.

Gooi de batterij niet weg. maar lever hem in als KCA.

Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.

6. When performing the installation, keep the rear of
the unit 5 cm (2 inches) or more away from walls
in order to obtain proper exhaust and radiation of
heat.

HSR-X200/X200P

Table of Contents

Manual Structure

Purpose of this manual .............................................................................................. 2

Related manuals......................................................................................................... 2

Contents ..................................................................................................................... 2

Trademark .................................................................................................................. 2

Caution for Handling the Unit with Built-in HDDs .................................................. 3

1. Installation

1-1. Installation Work Procedure .......................................................................1-1

1-2. Supplied Accessories ..................................................................................1-1

1-3. Operational Environment ............................................................................ 1-1

1-4. Installation Space ........................................................................................ 1-2

1-5. Power Supply .............................................................................................. 1-2

1-5-1. Voltage and Power Requirements .............................................. 1-2

1-5-2. Power Cord ................................................................................. 1-2

1-6. Optional Accessories ................................................................................... 1-3

1-7. Rack Mounting ............................................................................................ 1-3

1-8. Hard Disk Drive Unit .................................................................................. 1-4

1-9. Matching Connectors and Cables ................................................................ 1-4

2. Service Information

2-1. Main Parts Location .................................................................................... 2-1

2-2. Removing and Installing the Cabinet ..........................................................2-2

2-3. Removing and Installing the Main Parts .....................................................2-3

2-3-1. Removing and Installing the Power Unit ................................... 2-3

2-3-2. Removing and Installing the DC Fan Motor ..............................2-3

2-3-3. Removing and Installing the HDD Unit ..................................... 2-4

2-4. Removing and Installing the Board............................................................. 2-5

2-4-1. Removing and Installing the TB-4 Board .................................. 2-5

2-4-2. Removing and Installing the TB-2 Board and

Backup Battery ........................................................................... 2-5

2-4-3. Removing and Installing the TB-1 and TB-3 Boards ................2-6

2-4-4. Removing and Installing the PC-1 and CD-1 Boards ................ 2-7

2-4-5. Removing and Installing the OP-1 and OP-2 Boards ................2-8

3. Alignment

3-1. Supply Voltage Adjustment ........................................................................ 3-1

HSR-X200/X200P

1

Purpose of this manual

Related manuals

Manual Structure

This manual is the Service Manual Volume 1 of the digital surveillance recorder
HSR-X200/X200P.
This manual contains the maintenance information of this equipment, and servicing
information necessary for parts replacement and adjustments.

In addition to this Service Manual Volume 1, the following manuals are provided.

..

. Operating Instructions

..

HSR-X200/X200P (Supplied with equipment)

Parts number : 3-206-603-1X (For UC, CE)

3-206-603-2X (For CE)

..

. Service Manual Vol. 2 (Available on request)

..

Part number : 9-955-344-2X
Contains the semiconductor pin assingnments, parts lists, block diagrams, board
layouts and schematic diagrams.

Contents

Trademark

The sections covered in the manual are summarized below to give you a general
understanding of the manual.

Section 1 Installation

Describes the installation procedure and environment required during installation
and the connection with external equipment.

Section 2 Service Overview

Describes the replacement procedure of parts during repairing of this unit, the
locations of the main parts and boards, and notes on servicing.

Section 3 Alignment

Describes the adjustment procedure after part replacement.

Trademarks and registered trademarks used in this manual are follows.

. Windows is a registered trademark of Microsoft Corporation.

2

HSR-X200/X200P

Caution for Handling the Unit with Built-in HDDs

This unit has a built-in hard disk drive (HDDs). Pay careful attention to the followings and perform
operations with extra care when installing, servicing, and maintaining this unit.

Never give any mechanical shock and vibration

This may cause an HDD trouble or destroy the data in HDD.
. Pack this unit using the specified packing materials when carrying the unit. Use a cart with less-

vibration when carrying this unit by a cart. If an excessive mechanical shock and vibration are applied,
the HDD may be damaged.

. Never move this unit under power-on state. Take out or insert this unit from or into the rack in a state of

powering off. Also never install or remove the cabinet under power-on state.

. When putting the unit on the floor, put this unit gently with the four specified feet which is attached to

the bottom of the unit on the floor. If there are no feet on the bottom, attach them before putting this
unit, or put this unit gently so that no sound is generated.

Never operate the unit for 30 seconds after the power is turned off

The disks in HDD rotate by inertia for a while after the power is turned off. In this case, the heads are in
the unstable state. During this period, the HDD is more sensitive to a mechanical shock and vibration than
during power on state. Never give even a slight shock at least 30 seconds after the power is turned off.
Operations can be initiated (because the disks stop) after 30 seconds or more.

In the event of trouble in HDD

If there is something wrong with the HDD of this unit (a failure occurs in the HDD), handle this unit in
the same manner as described above. This protects the HDD from increase of the damage till confirming
the contents of the failure or analyzing the failure.

Pay careful attention to the following when handlings the HDD alone.

Notes when carrying or keeping the HDD

Pack the HDD using the specified packing materials when carrying or keeping the HDD. Moreover,
choose the method which the HDD is not subject to the vibration when carrying.

HSR-X200/X200P

3

Notes when replacing the HDD

Follow the procedure (described in Section 1) when replacing the HDD.
. If an excessive mechanical shock and vibration are applied, the unpacked HDD may be damaged.

Place the unpacked HDD in a horizonal position (with the printed board side up). Moreover, it is
recommended that the unpacked HDD is put on the specified HDD cushion.

. Use the specified shockless torque screwdriver when tightening and removing the screw during

replacing the HDD.
The HDD cushion and shockless torque screwdriver are available as a fixture.

HDD cushion : Part No. J-6530-060-A
Shockless torque screwdriver : Part No. J-6530-070-A

. HDD is easily affected by static electricity. Take measures against static electricity such as establish-

ing a ground, then install the HDD.

Handling of failed HDD

Handle the HDD that is removed because of a trouble or failure in the same manner as a normal HDD
following above precautions.

4

HSR-X200/X200P