How it Works
Sony
Loading...
HKC-T950
Table of contents
Loading...

Sony HDC-F950, HKC-T950 Installation And Maintenance Manual

HD COLOR CAMERA
HDC-F950
HD CCD BLOCK ADAPTOR
HKC-T950
INSTALLATION AND MAINTENANCE MANUAL 1st Edition Serial No. 10001 and Higher: HDC-F950 Serial No. 10001 and Higher: HKC-T950
! WARNING
This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement.
For HDC-F950
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
For HDC-F950
Laser Diode Properties
Material : In GaAsp Wave length : 1310 nm, 1550 Emission duration : Pulse code modulation Laser output power : _8 dBm
+4.4 _7.4
nm
For HDC-F950
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Vorsicht!
Explosionsgefahr bei unsachgemäßem Austausch
der Batterie.
Ersatz nur durch denselben oder einen vom
Hersteller empfohlenen ähnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben des
Herstellers.
ATTENTION
Il y a danger d’explosion s’il y a remplacement
incorrect de la batterie.
Remplacer uniquement avec une batterie du même
type ou d’un type équivalent recommandé par le
constructeur.
Mettre au rebut les batteries usagées conformément
aux instructions du fabricant.
ADVARSEL
Lithiumbatteri - Eksplosjonsfare.
Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten.
Brukt batteri returneres
apparatleverandøren.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en likvärdig typ
som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt gällande
föreskrifter.
VAROITUS
Paristo voi räjähtää jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laitevalmistajan
suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
1 (P)
For the customers in the Netherlands Voor de klanten in Nederland
Hoe u de batterijen moet verwijderen, leest u in de Onderhoudshandleiding.
Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA).
Für Kunden in Deutschland
Entsorgungshinweis: Bitte werfen Sie nur entladene Batterien in die Sammelboxen beim Handel oder den Kommunen. Entladen sind Batterien in der Regel dann, wenn das Gerät abschaltet und signalisiert “Batterie leer” oder nach längerer Gebrauchsdauer der Batterien “nicht mehr einwandfrei funktioniert”. Um sicherzugehen, kleben Sie die Batteriepole z.B. mit einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel.
For the customers in Japan
For the customers in the U.S.A. and Canada
RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you.
For more information regarding recycling of re­chargeable batteries, call toll free 1-800-822-8837, or visit http://www.rbrc.org/
Caution: Do not handle damaged or leaking Lithium-Ion batteries.
2 (P)

Table of Contents

Manual Structure
Purpose of this manual ........................................................................................ 3 (E)
Related manuals................................................................................................... 3 (E)
Contents ............................................................................................................... 4 (E)
1. Installation Overview
1-1. Checking the ROM and Software Version............................................ 1-1 (E)
1-2. Connectors and Cables ..........................................................................1-2 (E)
1-2-1. Connector Input/Output Signals ........................................... 1-2 (E)
1-2-2. Wiring Diagrams for Cables .............................................. 1-10 (E)
1-2-3. Connection Connectors/Cables .......................................... 1-11 (E)
1-2-4. Note in connecting CCU connector ................................... 1-11 (E)
1-3. Location of Printed Circuit Boards ..................................................... 1-12 (E)
1-4. Removing/Reinstalling the Side Panel (HDC-F950) ..........................1-14 (E)
1-5. Switch Setting on the Boards ..............................................................1-15 (E)
1-6. Adjusting the Position of the Shoulder Pad (HDC-F950) ...................1-20 (E)
1-7. Installing the Incom Panel Assembly to the Camera Backside
(HDC-F950) ........................................................................................1-20 (E)
1-8. Installing the Battery Adaptor BKP-L551 (HDC-F950) ..................... 1-21 (E)
1-9. Notes on Use of the RTS Kit (HDC-F950) .........................................1-21 (E)
1-10. Disconnecting/Reconnecting Flexible Card Wire ...............................1-22 (E)
2. Service Overview
2-1. Cleaning of Connector/Cable ................................................................2-1 (E)
2-2. Cleaning the Vent Portion of the Fan (HDC-F950 only) ......................2-3 (E)
2-3. Replacing the Fuse (HDC-F950) .......................................................... 2-4 (E)
2-4. Recommended Replacing Parts............................................................. 2-5 (E)
2-4-1. HDC-F950 ............................................................................2-5 (E)
2-4-2. HKC-T950 ............................................................................ 2-6 (E)
1 (E)
3. Setup Menu
3-1. Setup Menu ........................................................................................... 3-1 (E)
3-2. TOP Menu .............................................................................................3-3 (E)
3-3. USER Menu .......................................................................................... 3-4 (E)
3-4. USER MENU CUSTOMIZE Menu...................................................... 3-4 (E)
3-5. OPERATION Menu .............................................................................. 3-5 (E)
3-6. PAINT Menu ......................................................................................... 3-7 (E)
3-7. MAINTENANCE Menu ..................................................................... 3-18 (E)
3-8. FILE Menu ..........................................................................................3-25 (E)
3-9. DIAGNOSIS Menu .............................................................................3-30 (E)
4. File System
4-1. File Structure .........................................................................................4-1 (E)
4-2. Operator File ......................................................................................... 4-2 (E)
4-3. Preset Operator File............................................................................... 4-3 (E)
4-4. Scene File ..............................................................................................4-4 (E)
4-5. Reference Files ...................................................................................... 4-6 (E)
4-6. Lens File ................................................................................................ 4-8 (E)
4-7. OHB File ............................................................................................... 4-9 (E)
4-7-1. Storing the Black Shading and White Shading .................... 4-9 (E)
4-7-2. Adjusting the ND Offset .................................................... 4-10 (E)
4-8. File items .............................................................................................4-11 (E)
2 (E)

Purpose of this manual

Related manuals

Manual Structure

This manual is the installation and maintenance manual of HD Color Camera HDC­F950 and HD CCD Block Adaptor HKC-T950 for HDC-F950. This manual is intended for use by trained system and service engineers, and is provided information required for the installation and maintenance information .
Besides this installation and maintenance manual, the following manuals are avail­able.
..
. HDC-F950 Operation Manual (Supplied with HDC-F950)
..
This manual is necessary for the use and the operation of the HDC-F950. Part No. : 3-789-477-XX
..
. HKC-T950 Operation Manual (Supplied with HKC-T950)
..
This manual is necessary for the installation and operation of the HKC-T950. Part No. : 3-206-420-XX
..
. HDC-F950 e-manual (Tentative name) (Available on request)
..
This electronic manual intended for use by trained system and service engineers describes (replacement of main parts, SERVICE menu, electrical alignment, detailed parts list, block diagrams, schematic diagrams, and board layouts.) required for parts-level service of the HDC-F950. For obtaining, contact your local Sony Sales Office/Service Center.
..
. System Manual (Available on request)
..
This manual is necessary for connection and operation of this unit and other peripheral equipment. If this manual is required, please contact to your local Sony Sales Office/Service Center.
..
. “Semiconductor Pin Assignments” CD-ROM (Available on request)
..
This “Semiconductor Pin Assignments” CD-ROM allows you to search for semiconductors used in B&P Company equipment. Semiconductors that cannot be searched for on this CD-ROM are listed in the maintenance manual for the corresponding unit. The maintenance manual contains a complete list of all semiconductors and their ID Nos., and thus should be used together with the CD-ROM. Part number: 9-968-546-XX
3 (E)

Contents

The installation and maintenance manual is organized by following sections.
Section 1 Installation Overview
This section is described about the information that is required to install (switch setting on the board, connection information, and the like.) and when installing this unit.
Section 2 Service Overview
This section is described about the recommended replacing parts, replacing the fuse and the cleaning procedures.
Section 3 Setup Menu
This section is described about the setup menu (TOP menu, OPERATION menu, PAINT menu, MAINTENANCE menu, FILE menu and DIAGNOSIS menu).
Section 4 File System
This section is described about the file system to control data.
4 (E)
Section 1

Installation Overview

1-1. Checking the ROM and Software Version

When connecting the peripheral equipment in the list below to HDC-F950, be sure to check that the ROM and software version on each peripheral device is corre­sponding to the camera to be connected. If the ROM and software version is lower than the specified below, be sure to perform ROM replacement and updating the software. If ROM replacement and updating the software are required, contact your local Sony Sales Office/Service Center.
ROM
Peripheral equipment Board name Ref No. Rom version
MSU-700A/750 CPU-293/CPU-286 IC5, IC6/IC5, IC6 Ver. 1.10 or higher
RCP-720/721 MPU-79 IC10 Ver. 2.73 or higher
RCP-730/731 MPU-79 IC10 Ver. 2.73 or higher
RCP-740/741 MPU-79 IC10 Ver. 2.73 or higher
RCP-700/701 MPU-92 IC6 Ver. 2.73 or higher
RM-B150 CPU-266 IC4 Ver. 1.00 or higher
Software
Peripheral equipment Board name Software version
RCP-750/751 MPU-123 Ver. 1.01 or higher
RM-B750 MPU-124 Ver. 1.00 or higher
1-1 (E)

1-2. Connectors and Cables

1-2-1. Connector Input/Output Signals

HDC-F950 Connector Layout
!-
1
2
*
4 !,
7 9 !'
!=
!.
8
* : Use 4 connector by selecting PROMPTER OUT, GENLOCK IN and RET IN signals with the switch.
PROMPTER OUT signal become effective when the camera is connected to CCU. GENLOCK IN and RET IN signals become effective when the camera is used alone.
3![6!\
HKC-T950 Connector Layout
@-
@[ @-
@=
@= @\
!;
!/
@]
@/ !\
!]5
1-2 (E)
@[
Input/Output Signals
11
1 CCU connector
11
Based upon BTA S-004A/005A/006A 1.485 Gbps serial
Output Signals
22
2 EARPHONE OUT
22
EARPHONE mini jack
33
3 TEST OUT
33
BNC type 75 Z, 1.0 V p-p
**
*2
44
4 PROMPTER OUT
44
**
BNC type 75 Z, 1.0 V p-p
**
*1
55
5 HD SERIAL RET OUT
55
**
Based upon BTA-S004A, SMPTE-292M BNC type 75 Z, 0.8 V p-p 1.485 Gbps
![![
![ HD SERIAL LINK A OUT
![![
Based upon BTA-S004A, SMPTE-372M BNC type 75 Z, 0.8 V p-p 1.485 Gbps
77
7 RET CONTROL (6P FEMALE)
77
(External view)
No. Signal I/O Specifications
1 INCOM 1 IN Zi > 10 kZ
MIC ON/OFF ON : GND
OFF : OPEN
2 INCOM 2 IN Zi > 10 kZ
MIC ON/OFF ON : GND
OFF : OPEN
3 GND ——
4 NC No connection 5 RET 1 ON/OFF IN Zi > 10 kZ
ON : GND OFF : OPEN
6 RET 2 ON/OFF IN Zi > 10 kZ
ON : GND OFF : OPEN
!]!]
!] HD SERIAL LINK B OUT
!]!]
Based upon BTA-S004A, SMPTE-372M BNC type 75 Z, 0.8 V p-p 1.485 Gbps
@/@/
@/ VIDEO OUT (HKC-T950)
@/@/
BNC type 75 Z, 1.0 V p-p
Input Signals
**
*2
44
4 GENLOCK IN
44
**
BNC type 75 Z, 1.0 V p-p
**
*2
44
4 RET IN
44
**
BNC type 75 Z, 1.0 V p-p
66
6 Not used
66
*1 : HD SERIAL RET OUT signal become effective when the camera is
connected to CCU.
*2 : Use this connector by selecting PROMPTER OUT, GENLOCK IN and
RET IN signals with the switch on the rear panel of HDC-F950. PROMPTER OUT signal become effective when the camera is connected to CCU. GENLOCK IN and RET IN signals become effective when the camera is used alone.
88
8 DC OUT (4P FEMALE)
88
1
4
23
(External view)
No. Signal I/O Specifications
1 GND —— GND for POWER
2 NC No connection
3 NC No connection 4 UNREG OUT +12 V dc 500 mA (max)
1-3 (E)
99
9 REMOTE (8P FEMALE)
99
!-!-
!- INTERCOM CH1/CH2 (5P FEMALE)
!-!-
(External view)
No. Signal I/O Specifications
1 TX (+) HDC SERIAL DATA 2 TX (_) 3 RX (+) HDCU/MSU/RCP/CNU/VCS 4 RX (_) SERIAL DATA
5 TX GND —— GND for TX 6 POWER (+) OUT +26 V, 200 mA (max) 7 POWER GND —— GND for POWER (+) 8 VIDEO (X) 75 Z, 1.0 V p-p
CHASSIS GND —— CHASSIS GND
!/!/
!/ AUDIO IN CH1/CH2 (3P FEMALE)
!/!/
21
3
(External view)
No. Signal I/O Specifications
1 AUDIO (G) —— _60 dBu, _50 dBu, _40 dBu, 2 AUDIO (X) IN _30 dBu, _20 dBu, selectable
3 AUDIO (Y) IN High impedance, Balanced
(0 dBu = 0.775 Vrms)
(External view)
No. Signal I/O Specifications
1 INCOM MIC (Y) IN _20 dBu (CARBON MIC) 2 INCOM MIC (X) IN _60 dBu (DYNAMIC MIC)
3
GND (INCOM/PGM)
4 INCOM OUT 0 dBu
RECEIVE
5 PGM OUT 0 dBu
——
(0 dBu = 0.775 Vrms)
!=!=
!= DC IN (4P MALE)
!=!=
(External view)
No. Signal I/O Specifications
1 GND —— GND for DC (+)
2 NC No connection
3 NC No connection 4 DC (+)IN+10.5 to 17 V dc
1-4 (E)
!\!\
!\ LENS (12P FEMALE)
!\!\
!;!;
!; VF (20P FEMALE)
!;!;
(External view)
No. Signal I/O Specifications
1 RET VIDEO IN ENABLE : 0 V
ENABLE DISABLE : +5 V or OPEN
2 VTR START IN ENABLE : 0 V
/STOP DISABLE : +5 V or OPEN
3 GND —— GND for UNREG
4 AUTO SERVO OUT AUTO : +5 V
MANU : 0 V or OPEN
5 IRIS CONT OUT +3.4 V (F16) to
+6.2 V (F2.8)
6 UNREG OUT +10.5 V to +17 V
7 IRIS POSITION IN +3.4 V (F16) to
+6.2 V (F2.8)
8 AUTO/MANU OUT AUTO IRIS : 0 V
MANUAL IRIS : +5 V
9 EXTENDER IN EX 2 ON : GND
ON/OFF EX 0.8 ON : 30 kZ to GND
OFF : OPEN
EX 2 ON
EX 0.8 ON
10 ZOOM IN WIDE : 2 V
POSITION TELE : 7 V
11 FOCUS POSI IN ∞ : 7 V
(/LENS RX) min. : 2 V
12 (LENS TX) OUT
30 kΩ
(External view)
No. Signal I/O Specifications
1 S-DA TA IN/OUT TTL level
2 NC No connection
3 NC No connection
4 SCK OUT TTL level
5 NC No connection
6 NC No connection
7 NC No connection
8 G TALLY OUT ON : 5 V
OFF : GND
9 NC No connection
10 Y VIDEO OUT 1.0 V p-p, Zo = 75 Z
11 NC No connection
12 Y VIDEO OUT 1.0 V p-p, Zo = 75 Z
13 VIDEO GND —— GND for VIDEO
14 Pb VIDEO OUT ± 0.35 V p-p, Zo = 75 Z
15 Pr VIDEO OUT ± 0.35 V p-p, Zo = 75 Z
16 NC No connection
17 R TALLY OUT ON : 5 V
OFF : GND
18 NC No connection
19 UNREG GND —— GND for UNREG
20 UNREG OUT +10.5 V to +17 V
1-5 (E)
!'!'
!' EXT I/O (20P)
!'!'
!,!,
!, TRACKER (FEMALE)
!,!,
11
5 17 18 19 20
1 2 3 4
10
16
(External view)
No. Signal I/O Specifications
1 Y VIDEO (X) OUT 1.0 V p-p, Zo = 75 Z
2 Y VIDEO (G) —— GND for Y VIDEO 3 PROMPTER (X) OUT 1.0 V p-p, Zo = 75 Z
4 PROMPTER (G) —— GND for PROMPTER 5 Pr VIDEO (X) OUT ± 0.35 V p-p, Zo = 75 Z
6 Pr VIDEO (G) —— GND for Pr VIDEO 7 Pb VIDEO (X) OUT ± 0.35 V p-p, Zo = 75 Z
8 Pb VIDEO (G) —— GND for Pb VIDEO
9 SDA VF IN/OUT TTL level
10 VD OUT Negative Pulse,
3.0 V p-p, Low impedance
11 CALL ON IN ON : L (0 v)
OFF : H (+3 V)
12 VF POWER OFF OUT ON : H (+5 V)
OFF : L (0 V)
13 MAIN POWER OUT ON : +8 V
ON/OFF OFF : GND
14 SCL VF OUT TTL level
15 TALLY GND —— GND for TALLY
16 BACK TALLY OUT ON : 5 V
OFF : GND
17 PANEL DATA IN RX SERIAL DATA
18 PANEL DATA OUT TX SERIAL DATA 19 VF UNREG + OUT
+12 V (+10.5 V to +17.0 V)
20 GND —— GND for UNREG
1
2
6
11
16
5
3
4
7
8139
12
10
14
15
17
182019
(External view)
No. Signal I/O Specifications
1 TRK R (X) OUT TRACKER RECEIVE
0 dBu unbalanced
2 TRK R (G) —— GND for TRACKER R
3 GND —— GND for UNREG/TALLY
(UNREG/TALLY)
4 R TALLY OUT ON : 5 V (Open Collector)
OFF : 0 V (Open Collector)
5 TRK PGM (G) —— GND for PGM 6 UNREG OUT +12 V (+10.5 to +17.0 V)
7 TRK T (X) IN TRACKER TALK 8 TRK T (Y) IN 0 dBu /_20 dBu
High impedance balanced
9 TRK T (G) —— GND for TRACKER T 10 TRK PGM (X) OUT _20 dBu unbalanced
11 NC No connection
12 G TALLY OUT ON : 5 V (Open Collector)
OFF : 0 V (Open Collector)
13 NC No connection
14 RX_DATA (0) IN TRUNK DATA IN, RS232-C
15 RX_DATA (1) IN
16 NC No connection
17 NC No connection
18 TX_DATA (0) OUT
TRUNK DATA OUT, RS232-C
19 TX_DATA (1) OUT
20 GND ——
(0 dBu = 0.775 Vrms)
1-6 (E)
!.!.
!. FRONT MIC (3P FEMALE)
!.!.
21
3
(External view)
No. Signal I/O Specifications
1 CHU MIC (G) —— _60 dBu, _50 dBu, _40 dBu, 2 CHU MIC (X) IN _30 dBu, _20 dBu, selectable
3 CHU MIC (Y) IN High impedance, Balanced
(0 dBu = 0.755 Vrms)
@-@-
@- MIC (HKC-T950)
@-@-
(3P FEMALE) (3P MALE)
21
3
(External view) (External view)
No. Signal I/O Specifications
1 AUDIO (G) —— _60 dBu, _50 dBu, _40 dBu, 2 AUDIO (X) IN _30 dBu, _20 dBu, selectable
3 AUDIO (Y) IN High impedance, Balanced
1
2
3
(0 dBu = 0.755 Vrms)
@=@=
@= INCOM (HKC-T950)
@=@=
(5P FEMALE) (5P MALE)
5
(External view) (External view)
No. Signal I/O Specifications
1 INCOM MIC (Y) IN _20 dBu (CARBON MIC) 2 INCOM MIC (X) IN _60 dBu (DYNAMIC MIC)
3 GND (INCOMPGM) ——
4 INCOM RECEIVE OUT 0 dBu
5 PGM OUT 0 dBu
1
2
4
3
1
5
4
2
3
(0 dBu = 0.755 Vrms)
1-7 (E)
@[@[
@[ VF (HKC-T950)
@[@[
(20P FEMALE)
(20P FEMALE)
123
12 11 10 9 17 16 15
45678
141813
20
19
(External view)
No. Signal I/O Specifications
1 S DATA IN/OUT TTL level
2 NC No connection
3 NC No connection
4 SCK OUT TTL level
MANU : 0 V or OPEN
5 NC No connection
6 NC No connection
7 NC No connection
8 G TALLY OUT ON : 5 V
OFF : GND
9 NC No connection
10 NC No connection
11 NC No connection 12 Y VIDEO OUT 1.0 V p-p, Zo = 75 Z
13 VIDEO GND —— GND for VIDEO
14 NC No connection
15 NC No connection
16 NC No connection
17 R TALLY OUT ON : 5 V
OFF : GND
18 NC No connection
19 UNREG GND —— GND for UNREG 20 UNREG OUT +10.5 V to +1.7 V
12345
678910
11 12 13 14 15
16 17 18 19 20
(External view)
No. Signal I/O Specifications
1 S DATA IN/OUT TTL level
2 NC No connection
3 NC No connection
4 SCK IN TTL level
MANU : 0 V or OPEN
5 NC No connection
6 NC No connection
7 NC No connection
8 G TALLY IN ON : 5 V
OFF : GND
9 NC No connection
10 NC No connection
11 NC No connection 12 Y VIDEO IN 1.0 V p-p, Zi = 75 Z
13 VIDEO GND —— GND for VIDEO
14 NC No connection
15 NC No connection
16 NC No connection
17 R TALLY IN ON : 5 V
OFF : GND
18 NC No connection
19 NC No connection
20 NC No connection
1-8 (E)
@]@]
@] CAM BODY (HKC-T950)
@]@]
(26P MALE)
@\@\
@\ OPT HEAD (HKC-T950)
@\@\
(26P FEMALE)
B
6
5
A
4
11
3
17
10
2
16
9
1
8
22
15
14
7
21
20
13
19
12
24
18
23
(External view)
No. Signal I/O Specifications
A UNREG IN 13 V to 17 V
B UNREG GND —— GND for UNREG
1 OHB H OUT 0.3 V p-p Positive pulse
2 OHB H (G) —— GND for OHB H
3 G VIDEO (G) —— GND for G VIDEO
4 G VIDEO (X) OUT
5 R VIDEO (X) OUT
300 mV p-p, Zo = 75 Z (100 %) 300 mV p-p, Zo = 75 Z (100 %)
6 R VIDEO (G) —— GND for R VIDEO 7 B VIDEO (X) OUT 95 mV p-p, Zo = 75 Z (100 %)
8 B VIDEO (G) —— GND for B VIDEO 9 MIC (X) OUT _60 dBu, _50 dBu, _40 dBu, 10 MIC (Y) OUT _30 dBu, _20 dBu, selectable
11 INCOM/MIC GND —— GND for INCOM/MIC,
CHU F, IRIS CONT
12 IRIS CONT IN +3.4 V (F16) to +6.2 V (F2.8)
13 CHU F IN 0.3 V p-p Positive pulse
14 INCOM RECEIVE IN 0 dBu 15 INCOM MIC (X) OUT _20 dBu (CARBON MIC) 16 INCOM MIC (Y) OUT _60 dBu (DYNAMIC MIC)
17 CHU H IN 150 mV p-p Positive pulse 18 VF VIDEO (X) IN 180 mV p-p, Zi = 75 Z
19 VF VIDEO (G) —— GND for VF VIDEO,CHU H
20 PGM IN 0 dBu
21 RX COMMAND (X) IN
22 RX COMMAND (Y) IN 340 mV p-p
23 TX COMMAND (X) OUT
24 TX COMMAND (Y) OUT
B
6
5
11
17
16
22
21
24
A
4
3
10
2
9
15
20
23
1
8
7
14
13
12
19
18
(External view)
No. Signal I/O Specifications
A UNREG OUT 13 V to 17 V
B UNREG GND —— GND for UNREG
1 OHB H IN 0.3 V p-p Positive pulse
2 OHB H (G) —— GND for OHB H
3 G VIDEO (G) —— GND for G VIDEO 4 G VIDEO (X) IN 300 mV p-p, Zi = 75 Z (100 %) 5 R VIDEO (X) IN 300 mV p-p, Zi = 75 Z (100 %)
6 R VIDEO (G) —— GND for R VIDEO 7 B VIDEO (X) IN 95 mV p-p, Zi = 75 Z (100 %)
8 B VIDEO (G) —— GND for B VIDEO 9 MIC (X) IN _60 dBu, _50 dBu, _40 dBu, 10 MIC (Y) IN _30 dBu, _20 dBu, selectable
11 INCOM/MIC GND —— GND for INCOM/MIC,
CHU F, IRIS CONT
12 IRIS CONT OUT +3.4 V (F16) to +6.2 V (F2.8)
13 CHU F OUT 0.3 V p-p Positive pulse
14 INCOM RECEIVE OUT 0 dBu 15 INCOM MIC (X) IN _20 dBu (CARBON MIC) 16 INCOM MIC (Y) IN _60 dBu (DYNAMIC MIC)
17 CHU H OUT 150 mV p-p Positive pulse 18 VF VIDEO (X) OUT 180 mV p-p, Zo = 75 Z
19 VF VIDEO (G) —— GND for VF VIDEO, CHU H
20 PGM OUT 0 dBu
21 RX COMMAND (X) OUT
22 RX COMMAND (Y) OUT 340 mV p-p
23 TX COMMAND (X) IN
24 TX COMMAND (Y) IN
1-9 (E)

1-2-2. Wiring Diagrams for Cables

CCA-5 Cable
HDCZ Cable
Yellow
Black
Blue
Red
Brown
Gray
Red
Black
White
Red
Red
White
Blue
Red
White
Orange
White
Red
Yellow
White
1-10 (E)

1-2-3. Connection Connectors/Cables

Connection made with the connector panels during instal­lation or service, should be made with the connectors/ complete cable assemblies specified in the following list, or equivalent parts.
Indication Connection connector/cable
HDC-F950
CCU LEMO®
FUW. 3K. 93C. TLMC96
(HDCU-F950 side)
CAMERA LEMO®
PUW. 3K. 93C. TLCC96
TEST OUT 1-569-370-12 Plug, BNC PROMPTER OUT VIDEO OUT (BNC)
HD SERIAL LINK A/B 1-569-370-12 Plug, BNC or OUT BELDEN8281 Cable or HD SERIAL RET OUT equivalent
AUDIO IN 1-508-084-00 XLR, 3P Male or MIC IN ITT Cannon XLR-3-12C equivalent (3P FEMALE) Cable assembly
(supplied with HKC-T950, 0.8 m) 1-823-599-11
*3
MIC IN 1-508-083-00 XLR, 3P, Female or (3P MALE) ITT Cannon XLR-3-11C equivalent
Cable assembly (supplied with HKC-T950, 0.8 m) 1-823-599-11
*3
RET CONTROL 1-560-078-00 Plug, 6P Male or (6P FEMALE) HIROSE HR10-7PA-6P equivalent
DC OUT 1-566-425-11 Plug, 4P Male or (4P FEMALE) HIROSE HR10A-7P-4P equivalent
INTERCOM 1-508-370-11 XLR, 5P Male or INCOM ITT Cannon XLR-5-12C equivalent (5P FEMALE) Cable assembly
(supplied with HKC-T950, 0.8 m) 1-823-600-11
*3
INCOM 1-508-363-00 XLR, 5P Female or (5P MALE) ITT Cannon XLR-5-11C equivalent
Cable assembly (supplied with HKC-T950, 0.8 m) 1-823-600-11
CAM BODY 1-564-184-00 Plug, 26P Female or
Cable assembly
*3
*3
HDCZ-A10 (supplied with HKC-T950, 10 m) 1-823-615-11 HDCZ-A25 (option, 25 m) 1-823-616-11 HDCZ-A50 (option, 50 m) 1-823-617-11
*4
*4
Indication Connection connector/cable
OPT HEAD 1-564-183-31 Plug, 26P Male or (26P FEMALE) Cable assembly
*3
HDCZ-A10 (supplied with HKC-T950, 10 m) 1-823-615-11 HDCZ-A25 (option, 25 m) 1-823-616-11 HDCZ-A50 (option, 50 m) 1-823-617-11
DC IN 1-508-362-00 XLR, 4P Female or (4P MALE) ITT Cannon XLR-4-11C equivalent, or
Cable assembly 1-551-577-00 (Supplied with AC-550/550CE)
REMOTE 1-766-848-11 Plug, 8P Male or (8P FEMALE) CCA-5 cable assembly (option)
*2
CCA-5-10 (10 m) /CCA-5-3 (3 m) or REMOTE cable 1-783-372-11 (supplied with RM-B150, 10 m)
*1 *2
TRACKER HIROSE HR25-9P-20P equivalent (20P FEMALE)
VF Cable assembly (20P FEMALE) (supplied with HKC-T950, 0.7 m)
1-792-603-21
*1: Use of REMOTE cable enables to monitor video signals. *2: If using a cable of length different from a standard product, contact your
local Sony Sales Office/Service Center.
*3: Only for HKC-T950. *4: Caution in making the optical/electric signal composite cable:
When making the optical/electric signal composite cable used for this camera system, the connection connectors specified in this manual must be used in order to comply with the limits for EMC regulations.

1-2-4. Note in connecting CCU connector

It is recommendable to clean the optical contact portions mentioned below before connecting this unit to the camera control unit.
. CCU connector of this unit . Camera connector of the camera control unit . Optical/Electrical cable
It is also necessary to clean the optical contact portions mentioned below before using the HDC-F950 to the large lens adaptor CA-905L.
. CA cable of a large lens adaptor . CCU connector of a large lens adaptor
For details on a cleaning method, refer to Section 2-1 “Cleaning of Connector/Cable”.
1-11 (E)

1-3. Location of Printed Circuit Boards

HDC-F950
The circuit boards other than the dedicated boards for HDC-F950 have compatibility with the circuit boards installed in HDC-950.
RE-188
CN-1954
CN-1953
DPR-156
CN-2018
SW-1018
SW-1016
SW-2026
SW-1029
SW-1013
SW-1014
SW-1015
LP-113
CN-1964
RE-182
RE-184A (Dedicated for HDC-F950)
DU-104
SG-268
DAP-24
DAD-38 (Dedicated for HDC-F950)
VDA-55
DPR-241 (Dedicated for HDC-F950) VA-196A (Dedicated for HDC-F950)
CN-1952
SW-1017
RE-181A (Dedicated for HDC-F950)
AU-271
AT-130A *1 (Dedicated for HDC-F950)
1-12 (E)
BI-145
BI-145
DU-69
PA-239
NR-73
TG-214
RP-114
CN-1947
DR-523 (Dedicated for HDC-F950)
Filter Drive Board
CN-1961
*1: n
The AT-130 board installed in HDC-950 can be used for HDC-F950 by changing the software.
CN-2094
SW-1027
CN-1951
CN-2063
CN-1702B
CN-1955
TX-83B (Dedicated for HDC-F950)
RX-67A (Dedicated for HDC-F950)
TX-83A (Dedicated for HDC-F950)
SDI-81 (Dedicated for HDC-F950)
MB-1036 (Dedicated for HDC-F950)
1-13 (E)
HKC-T950
IF-845
AT-146
1-4. Removing/Reinstalling the Side
LE-256CN-2270
1. Unscrew the eight screws as shown in the figure, then
CN-2271
Panel (HDC-F950)
remove the inside panel and outside panel.
SW-1065 SW-1066
SW-1076
RE-202
CN-2202
Outside panel
Screws
Inside panel
Screws
2. Reinstall in the reverse order of removal step 1.
n
When reattaching the outside panel, be careful not to put the cables shown in the figure between the outside panel and the chassis.
Optical fiber cables
CN-2264
AT-147
CN-2203
IF-846
CN-2265
Coaxial cable
1-14 (E)

1-5. Switch Setting on the Boards

AU-271 board
INCOM 1 switch
INCOM 1 MIC GAIN switch
AU
CM
DYN INCOM 1
MIC GAIN
54 3 2 1
1
S101
A
S104
B
S1
+
0
_
S103
C
S102
S201
S2 S202
2345
S301
INCOM 2 switch
INCOM 2 MIC GAIN switch
MIC MONITOR switch
DYN INCOM 2
MIC GAIN
MIC MONITOR
D
S204
+
0
_
ON
OFF
S203
S303
G
S304
E
F
AU-271 board (A side)
S300
AU-271 board suffix -13 and higher (B side)
Ref. No. Name Contents Factory Setting
*1
S1-1
TRACKER INCOM2 ON/OFF Switch ON to mix the TRACKER TALK signal of the Tracker OFF
connector to CCU INCOM2 RECEIVE OUT.
*2
S1-2
S2-1
*2
Not used —— ——
PGM1 INCOM1 RECEIVE Switch ON to mix the PGM1 signal adjusted the sound volume by OFF MIX ON/OFF the PGM volume control to the INCOM1 RECEIVE signal before
the sound volume adjustment.
S2-2 PGM2 INCOM2 RECEIVE Switch ON to mix the PGM2 signal adjusted the sound volume OFF
MIX ON/OFF by the PGM volume control to the INCOM2 RECEIVE signal before
the sound volume adjustment.
S101-1 PGM1 MUTE ON/OFF Switch OFF to output the PGM1 signal to the PGM OUT of the OFF
INTERCOM1 connector.
S101-2 PGM2 MUTE ON/OFF Switch OFF to output the PGM2 signal to the PGM OUT of the ON
INTERCOM1 connector.
S101-3 INCOM1 MUTE ON/OFF Switch OFF to output the INCOM1 RECEIVE signal to the PGM OUT OFF
of the INTERCOM1 connector.
S101-4 INCOM2 MUTE ON/OFF Switch OFF to output the INCOM2 RECEIVE signal to the PGM OUT ON
of the INTERCOM1 connector.
S102-1 PGM1 MUTE ON/OFF Switch OFF to output the PGM1 signal to the INCOM OUT of OFF
the INTERCOM1 connector.
S102-2 PGM2 MUTE ON/OFF Switch OFF to output the PGM2 signal to the INCOM OUT of ON
the INTERCOM1 connector.
S102-3 INCOM1 MUTE ON/OFF Switch OFF to output the INCOM1 RECEIVE signal to the INCOM OFF
OUT of the INTERCOM1 connector.
S102-4 INCOM2 MUTE ON/OFF Switch OFF to output the INCOM2 RECEIVE signal to the INCOM ON
OUT of the INTERCOM1 connector.
A
B
C
D
E
F
G
1-15 (E)
Ref. No. Name Contents Factory Setting
S103 INCOM1 MIC GAIN +/0/_ Select the audio level of INTERCOM1/2 to be sent to CCU. 0
+ : +6dB
0 : 0dB _ : _6dB
S104 INCOM1 MIC TYPE Select from two options below in accordance with the microphone CM
of the head set connected to the INTERCOM1/2 connector. CM : Carbon microphone DYN : Dynamic microphone
S201-1 PGM1 MUTE ON/OFF Switch OFF to output the PGM1 signal to the PGM OUT of the ON
INTERCOM2 connector.
S201-2 PGM2 MUTE ON/OFF Switch OFF to output the PGM2 signal to the PGM OUT of OFF
the INTERCOM2 connector.
S201-3 INCOM1 MUTE ON/OFF Switch OFF to output the INCOM1 RECEIVE signal to the PGM ON
OUT of the INTERCOM2 connector.
S201-4 INCOM2 MUTE ON/OFF Switch OFF to output the INCOM2 RECEIVE signal to the PGM OFF
OUT of the INTERCOM2 connector.
S202-1 PGM1 MUTE ON/OFF Switch OFF to output the PGM1 signal to the INCOM OUT of the ON
INTERCOM2 connector.
S202-2 PGM2 MUTE ON/OFF Switch OFF to output the PGM2 signal to the INCOM OUT of the OFF
INTERCOM2 connector.
S202-3 INCOM1 MUTE ON/OFF Switch OFF to output the INCOM1 RECEIVE signal to the INCOM ON
OUT of the INTERCOM2 connector.
S202-4 INCOM2 MUTE ON/OFF Switch OFF to output the INCOM2 RECEIVE signal to the INCOM OFF
OUT of the INTERCOM2 connector.
S203 INCOM2 MIC GAIN +/0/_ Select the audio level of the INTERCOM1/2 to be sent to CCU. 0
+ : +6dB 0 : 0dB _ : _6dB
S204 INCOM2 MIC TYPE Select from two options below in accordance with the microphone of CM
the head set connected to the INTERCOM 1/2 connector. CM : Carbon microphone DYN : Dynamic microphone
*3
S300-1
AUDIO1 +12 V OFF/ON Switch ON to supply +12 V for MIC POWER to the microphone OFF
connected the AUDIO IN 1 connector.
*3
S300-2
AUDIO2 +12 V OFF/ON Switch ON to supply +12 V for MIC POWER to the microphone OFF
connected the AUDIO IN 2 connector.
S301-1 TRACKER RECEIVE OUT Switch ON to mix the PGM1 signal to the TRACKER RECEIVE OUT OFF
PGM1 MIX of the TRACKER connector.
S301-2 TRACKER RECEIVE OUT Switch ON to mix the PGM2 signal to the TRACKER RECEIVE OUT OFF
PGM2 MIX of the TRACKER connector.
*1
S301-3
TRACKER RECEIVE OUT Switch ON to mix the INCOM2 RECEIVED signal to the TRACKER OFF IMCOM2 RECEIVE MIX RECEIVE OUT of the TRACKER connector.
*1
S301-4
TRACKER RECEIVE OUT Switch ON to mix the INCOM2 TALK signal to the TRACKER OFF INCOM2 TALK MIX RECIVE OUT of the TRACKER connector.
S303 MIC MONITOR ON/OFF Switch ON to monitor the microphone input signal at the INCOM OUT OFF
or EARPHONE OUT.
S304 TRACKER (T) 0/_20 Select the input level of the TRACKER Connector. 0
0 : 0dBu _20 : _20dBu (0dBu = 0.775 Vrms)
1-16 (E)
*1: The Tracker connector communicates to INCOM1 at the standard setting, yet it is communicable to INCOM2 by setting S1-1, S301-1
and S301-4 to ON.
*2: When setting S2-1 or S2-2 to ON, set bit1 and bit2 of S101, S102, S201 and S202 as shown below to prevent PGM1 and PGM2
signals from being mixed double.
S2-1 S101, 102, 201, 202 S2-2 S101, 102, 201, 202
bit1 bit12
ON ON ON ON
INCOM1
PGM 1
PGM 2
PGM1/2 swiitch (Panel)
INCOM2 PGM1/2 swiitch (Panel)
bit1 bit2 bit3 bit4
bit1 bit2 bit3 bit4
S101
S102
PGM OUT
INCOM OUT
INTERECOM CH1
INTERECOM CH1
CCU
S2-1
INCOM1
S2-2
INCOM2
bit1 bit2 bit3 bit4
bit1 bit2 bit3 bit4
S201
S202
PGM OUT
INCOM OUT
INTERECOM CH2
INTERECOM CH2
n
Each bit of S101, S102, S103 and S104 is opened when it is set to “ON” position. Set to “OFF”position to close the switch.
*3: AU-271 board suffix -13 and higher.
1-17 (E)
DU-104 board
2
1
A
S1
S4
B
S2
DU-104 board (A side)
[Reference][Reference]
[Reference]
[Reference][Reference]
The switch setting on this board is valid only when connecting the RTS kit (optional) to the INTERCOM2 connector.
Ref. No. Name Contents Factory Setting
S1 RTS1 RTS 1/NORM/POW Selects the function of the RTS CH1 side. NORM
S2 RTS2 RTS 2/NORM/POW Selects the function of the RTS CH2 side. NORM
S4-1 RTS1 ON/OFF Switch ON to use the RTS CH1 as the INCOM1 signal line. OFF
S4-2 RTS2 ON/OFF Switch ON to use the RTS CH2 as the INCOM2 signal line. OFF
RTS 1 : RTS CH1 of the RTS kit operates as INCOM1 signal line. NORM : Select NORM except when connecting to the RTS kit. POW : RTS CH1 of the RTS kit operates as the power supply line
for the RTS belt pack.
RTS 2 : RTS CH2 of the RTS kit operates as INCOM2 signal line. NORM : Select NORM except when connecting to the RTS kit. POW : RTS CH2 of the RTS kit operates as the power supply line
for the RTS belt pack.
m
When not connecting the RTS kit, make the settings same as factory settings. When S4-1 setting is ON, set S1 to RTS1, S201-1 through S201-4 on the AU-271 board to ON. When S4-2 setting is ON, set S2 to RTS2, S201- through S201-4 on the AU-271 board to ON.
1-18 (E)
Loading...
+ 60 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use