Page 1
HD MASTER SET-UP KIT
HKCF-700
INSTALLATION AND MAINTENANCE MANUAL
1st Edition (Revised 3)
Page 2
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
Page 3
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 2 (E)
Contents ............................................................................................................... 2 (E)
1. Installation
1-1. Installing HKCF-700 in CNU-500........................................................1-2 (E)
1-1-1. Modifying AT-100 Board ....................................................1-2 (E)
1-1-2. Replacing PC Board/Harness ...............................................1-6 (E)
1-2. Installing HKCF-700 in CNU-700........................................................1-7 (E)
1-2-1. Modifying AT-89 Board ......................................................1-7 (E)
1-2-2. Replacing PC Board/Harness ...............................................1-7 (E)
1-3. Setting MSU Master Control Unit ........................................................1-9 (E)
1-4. Setting Switches for Digital Video Selector/Routing Switcher ............1-9 (E)
2. Spare Parts
2-1. Notes on Repair Parts............................................................................2-1 (E)
2-2. Electrical Parts List ..................................................................................... 2-2
2-3. Supplied Accessories ..................................................................................2-4
3. Semiconductor Pin Assignments
4. Schematic Diagrams
IF-624 Board ............................................................................................... 4-2
IF-625 Board ............................................................................................... 4-4
5. Board Layouts
IF-624 Board ............................................................................................... 5-1
IF-625 Board ............................................................................................... 5-2
HKCF-700
1 (E)
Page 4
Purpose of this manual
Contents
Manual Structure
This manual is the maintenance manual for HD MASTER SET-UP KIT HKCF-700.
This manual describes the information items necessary when the unit is supplied and
installed, items that premise the service based on the components parts such as
alignment, schematic diagrams, board layouts and spare parts lists, assuming use of
system and service engineers.
The following are summaries of the each section for understanding the manual.
Section 1 Installation
Describes how to install the HKCF-700 in the CNU-500/700 and MSU-700.
Section 2 Spare Parts
Describes electrical parts list used in the unit.
Section 3 Semiconductor Pin Assignments
Describes function diagrams and pin names of semiconductor used in the unit.
Section 4 Schematic Diagrams
Describes schematic diagrams for every circuit board.
Section 5 Board Layouts
Describes board layouts for every circuit board.
2 (E)
HKCF-700
Page 5
Section 1
Installation
By installing the HKCF-700 in the CNU-500/CNU-700
and MSU-700 respectively, they can be activated in the
HD system.
This section explains how to install the HKCF-700 in the
CNU-500/CNU-700.
Configuration of HKCF-700
For CNU-500
. IF-625 board
. CNU-500 harness (15P-15P)
For CNU-700
. IF-624 board
. CNU-700 harness (12P-15P)
. RS-422 harness (30P-30P)
HKCF-700
1-1 (E)
Page 6
1-1. Installing HKCF-700 in CNU-500
1-1. Installing HKCF-700 in CNU-500
Confirmation of ROM version
Be sure to check that the ROMs version for IC4 and IC5
on the AT-100 board in CNU-500 are V2.71 and higher.
If ROM replacement is required, contact your local Sony
Sales Office/Service Center.
1-1-1. Modifying AT-100 Board
Modifying the AT-100 board is necessary prior to
installation. Proceed as follows. You can modify without
removing the AT-100 board from the CNU-500.
Preparation
Loosen the two screws to remove the front panel.
Remove the four screws to remove the top panel.
PWH3 x 5
Top panel
PWH3 x 5
M4 x 20
Front panel
Parts required
The following are not supplied with the unit. Get them
ready.
Description P/N Q’ty
Resister, Carbon 100 Z 1-247-807-11 2
IC uPD71051GB-10-3B4 8-759-149-05 1
Board Connector (15P) 1-695-209-11 1
Jumper Wire (l = 10 mm) –– 2
Jumper Wire (l = 35 mm) –– 1
Jumper Wire (l = 210 mm) –– 1
Jumper Wire (l = 215 mm) –– 1
Sony Bond SC608LVZ 7-432-912-52 1
1. Solder a 100-ohm carbon resistor between pins 2 and 5
of IC1111 (H-4). (See Fig 1_1)
2. Solder a 100-ohm carbon resistor between pins 3 and 4
of IC1111 (H-4). (See Fig 1_2)
3. Solder IC (uPD71051GB-10-3B4) at the traces of
IC1104 (H-6). (See Fig 1_3)
4. Solder a board connector (15P) at the traces of CN9
(K-13). (See Fig 1_4)
5. Cut traces at pins 12 and 13 of CN9 (K-13).
(See Fig 1_5)
6. Solder five jumper wires between the followings.
(1) Between pins 17 and 19 of IC1111* (l = 10 mm)
(See Fig 1_6)
(2) Between pins 1 and 2 of S1101 (l = 10 mm)
(See Fig 1_7)
(3) Between R130 (pin 56/IC45 side) and R192 (GND
side) (l = 30 mm) (See Fig 1_8)
(4) Between pin 12 of CN9 and pin 1 of CN7
*
(l = 215 mm) (See Fig 1_9)
(5) Between pin 13 of CN9 and pin 5 of CN7
*
(l = 210 mm) (See Fig 1_!/)
1-2 (E)
M4 x 20
7. Glue 215 mm long and 210 mm long jumper wires on
the AT-100 board with a Sony Bond at three points (at
least) as shown in Fig 1 in a shaded pattern.
*
No electrical part is mounted at IC1111 and CN7.
HKCF-700
Page 7
1-1. Installing HKCF-700 in CNU-500
(Fig. 1)
2
3
4
5
6
7
8
EFGHJ KLM NO
2
1
6
3
7
10
11
12
13
14
9
8
4
5
9
10
15
HKCF-700
AT-100 board (Component side)
1-3 (E)
Page 8
1-1. Installing HKCF-700 in CNU-500
RDEN-N
OUTA04
OUTA05
OUTA06
OUTA07
WREN-N
RESE-P1
OUTA00
OUTA01
PIO-CS0
OUTA02
OUTA03
F-2
RD
PA4
PC14
R161 47k
PA5
45
PC10
INC10
INC11
R162 47k
PA6
PC11
R166 47k
PA7
PC12
INC12
INC13
R168 47k
WR
PC13
PB10
INB10
12 43
2345
RESET
PB11
INB11
MODE
CS0
PA0
PA1
PA2
PA3
SEL0
NC
A1
A0
PC07
PC06
NC
PC05
PC04
PC00
PC01
PC02
NC
PC03
NC
PA17
PA16
PA15
NC
PA14
PA13
PA12
PA11
PA10
NC NC
CS1
GND
SEL1
PC17
PC16
PC15
2526 27 28 29 30 3132 33 34 35 36 3738 39 40
PIO-CS1
INC17
INC14
INC15
INC16
S2 S3
1
3
5
7
9
11
13
15
2
4
6
8
SW
10
12
14
16
GND
PB12
INB12
1
C
D0
D0
PB13
INB13
D1
65666768697071727374757677787980
D1
NC
D2
D3
NC
D4
D5
D6
D7
PB07
PB06
NC
PB05
PB04
NC
PB03
PB02
PB01
PB00
NC
VCC
PB17
PB16
PB15
PB14
INB14
F1
L16
R196
2.2k
D4
HLMP-6500-010
+5V
C101
0.1
+5V GND
R1219
47k
INB10
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
INB07
INB06
INB05
INB04
INB03
INB02
INB01
INB00
INB17
INB16
INB15
D2
D3
D4
D5
8
D6
D7
INB16
INB17
IFIO-CS
RDEN-N
WREN-N
DATA R/W
RESE-P1
IFIO-INT
INB11
INB12
INB13
INB14
INB15
R191 47k
R192 47k
R193 47k
R194 47k
R195 47k
C110
0.1
C111
C112
220
220
10V
10V
:AL
:AL
E7E6E5E4E3E2E1
5
R171 47k
R172 47k
R175 47k
R176 47k
DOWN
S4
3
1
2
UP
CANSEL
S5
3
1
2
SET
V1V2V3
12V
E
-12V
R198
270
A4 A5 A6 A7 A8
CN7-5 pin
CN7-1 pin
OUTA06
OUTA05
OUTA04
9
10
OUTA17
,,
OUTA16
OUTA15
OUTA14
OUTA13
OUTA12
OUTA11
OUTA10
D0
D1
D2
D3
D4
D5
D6
D7
A2
A3
A4
A6
A7
A8
A9
A10
VCC+5V
POWER LED
IFI0-CS
RDEN-N
WREN-N
DATA R/W
RESE-P1
IFIO-INT
+5V
COMMON
+12V
-12V
GND
GND
GND
+5V
OUT03
OUT07
OUT06
OUT05
OUT04
IN/OUT17
IN/OUT16
IN/OUT15
IN/OUT14
IN/OUT13
IN/OUT12
IN/OUT11
IN/OUT10
D0
D1
D2
D3
D4
D5
D6
D7
A2
A3
A4
A6
A7
A8
A9
A10
7
6/7
CN2 6PA2 A3
1
2
3
4
5
6
8
6/7
9
7/7
10
7/7
11
7/7
12
7/7
13
7/7
14
7/7
4
CN9
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
15
7/7
16
7/7
17
7/7
18
7/7
19
7/7
20
7/7
21
7/7
22
7/7
23
7/7
24
7/7
25
7/7
26
7/7
27
7/7
28
7/7
29
7/7
30
7/7
1-4 (E)
AT-100(2/7)
1-658-249-13
LOT NO. 606-
B-¥CNU500-AT100-13
HKCF-700
Page 9
DRESS BUS
100
1-1. Installing HKCF-700 in CNU-500
2/7
L1103
1µH
C1125
10
1
10V
IFIO-INT
CN9-12 pin
14
9
10
,
R1118
47k
ATA BUS
NTROL BUS
DRESS BUS
ATA BUS
NTROL BUS
IC1104
µPD71051GB-10-3B
4
NC
CTS
1
NC
TXEMP
2
NC
3
TXDATA
4
CLK
5
RESET
6
NC
7
DSR
8
RTS
9
DTR
10
NC
11
NC
NC
RXCLK
VDD
1213 14 15 16 17 1819 20 21 22
C1106
NM
IC1105
µPD71051GB-10-3B
4
NC
CTS
1
NC
TXEMP
2
NC
3
TXDATA
4
CLK
5
RESET
6
NC
7
DSR
8
RTS
9
DTR
10
NC
11
NC
NC
RXCLK
VDD
1213 14 15 16 17 1819 20 21 22
C1105
0.1
TXRDYNCRXRDY
SYNC/BRK
1104
D0D11CD2D3
D0D1D2
TXRDYNCRXRDY
SYNC/BRK
1105
D0D11CD2D3
D0D1D2
RD0
RD
D3
RD0
RD
D3
SIO-CS0
D
C/
RXDATA
A2 A2
SIO-CS1
D
C/
RXDATA
3435363738394041424344
CS
TXCLK
GND
3435363738394041424344
CS
TXCLK
GND
3
NC
33
NC
32
NC
31
WR0
WR
30
29
D7RESE_P0
D7
28
NC
27
D6
D6
26
D5
D5
25
D4
D4
24
NC
23
NC
NC
INA10
R1127
47k
2
100
NC
33
NC
32
NC
WR0
31
WR
30
D7RESE_P0
29
D7
28
NC
D6
27
D6
D5
26
D5
D4
25
D4
24
NC
23
NC
NC
INA11
R1128
47k
6
C1111
NM
C1112
NM
C1113
1
25V
C1114
1
25V
IC1111
MAX238CWG-T
NM
10
C1+
12
C1-
13
C2+
14
C2-
5
T1IN
18
T2IN
1111
19
T3IN
21
T4IN
6
R1OUT
4
R2OUT
22
R3OUT
17
R4OUT
IC1112
MAX238CWG-T
10
C1+
12
C1-
13
C2+
14
C2-
5
T1IN
18
T2IN
1112
19
T3IN
21
T4IN
6
R1OUT
4
R2OUT
22
R3OUT
17
R4OUT
VCC
GND
VCC
GND
9
8
9
8
V+
V-
T1OUT
T2OUT
T3OUT
T4OUT
R1IN
R2IN
R3IN
R4IN
V+
V-
T1OUT
T2OUT
T3OUT
T4OUT
R1IN
R2IN
R3IN
R4IN
11
C1117
NM
15
C1119
NM
2
1
24
20
7
3
23
16
C1118
11
1
25V
15
C1121
1
25V
2
1
24
20
7
3
23
16
TXD0
DTR0
RTS0
DCD0
RXD0
DSR0
CTS0
SIGNAL GND
CN9-13 pin
TXD1
DTR1
RTS1
DCD1
RXD1
DSR1
CTS1
SIGNAL GND
CN7
NM
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
10
CN7(1/8)
CN7(2/8)
CN7(3/8)
CN7(4/8)
CN7(5/8)
CN7(6/8)
CN7(7/8)
CN7(8/8)
CN8(1/10) 10P
CN8(2/10) 10P
CN8(3/10) 10P
CN8(4/10) 10P
CN8(5/10) 10P
CN8(6/10) 10P
CN8(7/10) 10P
CN8(8/10) 10P
CN8(9/10) 10P
CN8(10/10) 10P
SN74HC4040ANS-E0
IC1101(3/3)
7WU04FU(TE12R)
17
HKCF-700
IC1102
5
10
C1104
0.1
VCC
1102
RD
7
L1100
1µH
16
9
Q0
7
Q1
R1119 100
6
Q2
R1120 100
5
Q3
R1121 100
3
Q4
R1122 100
2
Q5
R1123 100
4
Q6
R1124 100
13
Q7
R1125 100
12
Q8
R1126 100
14
Q9
15
Q10
1
Q11
GND
11
8
S1100
2
1
4
3
6
5
8
7
SW SW
10
9
12
11
14
13
16
15
S1101
NM
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
C1115
10
10V
:TA
AT-100(7/7)
1-658-249-13
LOT NO. 606-
B-¥CNU500-AT100-12
NOTE
NM:NO MOUNT
1-5 (E)
Page 10
1-1. Installing HKCF-700 in CNU-500
1-1-2. Replacing PC Board/Harness
Parts required
The following are supplied with the unit.
Description Q’ty
IF-625 Board 1
CNU-500 Harness (15P-15P) 1
1. Remove the two screws (B3 x 6) from the rear panel
to remove the CN-1259 board.
2. Disconnect the connector CN1 from the CN-1259
board.
CN1
CN-1259 board
B3 x 6
3. Connect the connector disconnected in Step 2 to CN1
on the IF-625 board.
4. Connect between CN6 on the IF-625 board and CN9
on the AT-100 board with a CNU-500 harness.
5. Install the IF-625 board to the rear panel by the two
screws which were removed in Step 1.
CNU-500
harness
CN6
IF-625 board
CN1
B3 x 6
AT-100 board
CN9
CNU-500
6. Fasten the CNU-500 harness by two clamps.
Clamps
7. Set the switch S2-2 on the AT-100 board according to
a waveform monitor to be used.
ON : HD ANALOG system waveform monitor
(Sony Tektronix 1730HD or equivalent)
OFF : RECALL system waveform monitor
8. Install the top panel and front panel in the reverse
order of removal.
1-6 (E)
HKCF-700
Page 11
1-2. Installing HKCF-700 in CNU-700
1-2. Installing HKCF-700 in CNU-700
Confirmation of ROM version
Be sure to check that the ROMs version for IC4 and IC5
on the AT-89/89A board in CNU-700 are V2.10 and
higher.
If ROM replacement is required, contact your local Sony
Sales Office/Service Center.
1-2-1. Modifying AT-89 Board
If you install the HKCF-700 in the CNU-700 with the
following serial number, modifying the AT-89 board is
necessary prior to installation. Proceed as follows.
Applicable Serial No.
CNU-700 (UC) 10001 through 15080
CNU-700 (J) 30001 through 35015
CNU-700 (CE) 40001 through 45040
* It is unnecessary to modify the CNU-700 with the
following serial number.
CNU-700 (UC) 15081 and higher
CNU-700 (J) 35016 and higher
CNU-700 (CE) 45041 and higher
Preparation
Remove the front panel of the CNU-700 and pull the
AT-89 board out of the third slot from the top.
(Refer to Section 1-2-2, Steps 9 and 10.)
1-2-2. Replacing PC Board/Harness
Parts required
The following are supplied with the unit.
Description Q’ty
IF-624 Board 1
RS-422 Harness (30P-30P) 1
CNU-700 Harness (12P-15P) 1
(with HKCF panel attached)
PC Board Spacer 1
1. Remove the two screws (PWH3 x 6) to remove the
command connector assembly.
2. Remove the six screws (B3 x 5) to remove the rear
panel.
3. Remove the two screws (PWH3 x 6) to remove the
blank panel from the rear panel.
CNU-700
Command connecter assembly
Rear panel
B3 x 5
PWH3 x 6
Parts required
The following are not supplied with the unit. Get them
ready.
Description P/N Q’ty
Board Connector (30P) 1-561-772-00 2
Solder two board connectors (30P) at the traces of CN1
(D-3) and CN2 (F-3) respectively on the AT-89 board.
HKCF-700
PWH3 x 6
B3 x 5
Blank panel
PWH3 x 6
1-7 (E)
Page 12
1-2. Installing HKCF-700 in CNU-700
4. Install the HKCF panel (with harness) to the rear panel
by the two screws which were removed in Step 3.
5. Connect the CNU-700 harness to CN14 on the MB562 board.
6. Disconnect the harness between CN12 on the MB-562
board and CN15 on the CN-1001 board and then
reconnect between them with the supplied RS-422
harness.
n
Connect the RS-422 harness observing the correct
orientation.
The following two labels are put on the housing
surface at each end of the RS-422 harness.
[15] → To CN15/CN-1001 board
[12] → To CN12/MB-562 board
7. Install the command connector assembly in the reverse
order of removal.
8. Install the rear panel by the six screws in the reverse
order of removal.
Command connecter assembly
RS-422
harness
Rear panel
B3 x 5
PWH3 x 6
PWH3 x 6
HKCF Panel
B3 x 5
MB-562 board
CN15
PWH3 x 6
CN12
CN14
CNU-700
harness
B3 x 5
9. Loosen the two screws to remove the front panel.
10. Pull the AT-89/AT-89A board out of the third slot
from the top.
11. Set the switch S1-1 on the IF-624 board according to a
waveform monitor to be used.
ON : HD ANALOG system waveform monitor
(Sony Tektronix 1730HD or equivalent)
OFF : RECALL system waveform monitor
12. Secure the IF-624 board to the AT-89/AT-89A board
by using the supplied PC board spacer while connecting CN1 to CN1 and CN2 to CN2 each other.
CN1
CN2
CN2
IF-624 board
PC board
spacer
CN1
AT-89/89A board
13. Pull the IF-480/IF-777 board out of the first slot from
the top. Set the switches on the IF-480/IF-777 board as
follows.
S802 to S806 : Short-circuit between Pins 2 and 3 by a
short plug (to provide an RS-422
command interface)
S901 : Set S901-4 to ON, and S901-5 and
S901-6 to OFF (to establish
a 38.4 kbps baud rate)
n
Some CNU-700 has an optional IF-480/IF-777 board
in its second slot. For the optional board, however, the
above switch settings are not needed.
(If the setting is changed, it will be ignored.)
14. Return the AT-89/AT-89A and IF-480/IF-777 boards
to their normal position.
15. Reinstall the front panel.
Screw
1-8 (E)
Front panel
AT-89/89A board
Screw
HKCF-700
Page 13
1-4. Setting Switches for Digital Video Selector/Routing Switcher
1-3. Setting MSU Master Control Unit
1-3. Setting MSU Master Control Unit
Confirmation of ROM version
If using a MSU-700 in the system, be sure to check the
ROM version for IC10 on the CPU-171 board is V3.01 or
higher.
If ROM replacement is required, contact your local Sony
Sales Office/Service Center.
If using a MSU-700A/750, you do not have to replace the
ROM.
Setting of the MSU Assignment
Set the control mode to the LOCAL MSU mode (LOCAL
mode) using the MSU assignment menu. Refer to the
BVP-900-series System Manual BKP-9901 (available
separately) Section 3-4-3 “MSU Assignment” for the
setting procedure.
1-4. Setting Switches for Digital Video
Selector/Routing Switcher
As for system configurations, refer to the operation manual
supplied with HDCU-700A.
Cascading HD digital video selector MP1007A
When connecting up to nine cameras, set the REMOTE2
unit address switch “1” of the MP1007A to ON and the
other unit address switches to OFF.
When connecting ten or more cameras and cascading the
HD digital video selectors, set the unit address switch “2”
of the second selector to ON and the others to OFF. And
set the command mode to “NO RETURN RESPONSE” for
the both HD digital video selectors.
SD digital video routing switcher DVS-V1201
When connecting up to 12 cameras, set the REMOTE2
unit address switch “5” of the DVS-V1201 to ON and the
other unit address switches to OFF.
And set the command mode to “NO RETURN RESPONSE” for the SD digital video routing switchers.
HKCF-700
1-9 (E)
Page 14
Page 15
2-1. Notes on Repair Parts
1. Safety Related Components Warning
w
Components marked ! are critical to safe operation.
Therefore, specified parts should be used in the case of
replacement.
2. Standardization of Parts
Some repair parts supplied by Sony differ from those
used for the unit. These are because of parts
commonality and improvement.
Parts list has the present standardized repair parts.
3. Stock of Parts
Parts marked with “o” at SP (Supply Code) column of
the spare parts list may be not stocked. Therefore, the
delivery date will be delayed.
Section 2
Spare Parts
4. Units Representation
The following represented units are changed or
omitted in writing.
Units Representation
Capacitance µFuF
Inductance µHuH
Resistance Z Abbreviation
HKCF-700
2-1
2-1 (E)
Page 16
2-2. Electrical Parts List
----------- IF-624 BOARD
----------- Ref. No.
or Q’ty Part No. SP Description
------------
IF-625 BOARD
------------
Ref. No.
or Q’ty Part No. SP Description
1pc A-8273-738-A o MOUNTED CIRCUIT BOARD, IF-624
1pc A-8273-740-A o MOUNTED CIRCUIT BOARD, IF-625
1pc 3-603-242-01 o CONNECTOR PLATE(D SUB)
C1 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V
6pcs 3-711-228-01 o STANDOFF, D-SUB CONN.
C2 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V
C3 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V
C4 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V
C5 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V
C1 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V
C2 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V
C3 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V
C4 1-104-852-11 s TANTAL 22uF 20% 10V
C6 1-104-852-11 s TANTAL 22uF 20% 10V
CN1 1-564-238-11 o CONNECTOR, 30P, MALE
CN2 1-564-238-11 o CONNECTOR, 30P, MALE
C5 1-164-156-11 s CERAMIC, CHIP 0.1uF 25V
CN1 1-506-478-11 o CONNECTOR, 13P, MALE
CN2 1-563-890-21 s CONNECTOR, D-SUB 9P, FEMALE
CN3 1-562-382-31 s CONNECTOR, BNC, FEMALE
IC1 8-759-154-60 s IC UPD71055GB-10-3B4
IC2 8-759-082-57 s IC TC7W04FU
CN4 1-562-382-31 s CONNECTOR, BNC, FEMALE
CN5 1-562-382-31 s CONNECTOR, BNC, FEMALE
IC3 8-759-049-70 s IC SN74HC138APW-E05
IC4 8-759-050-06 s IC SN74HC157APW-E05
IC5 8-759-050-06 s IC SN74HC157APW-E05
CN6 1-695-209-11 s CONNECTOR, 15P, MALE
CN7 1-563-826-21 s CONNECTOR D-SUB 15P, FEMALE
CN8 1-563-890-21 s CONNECTOR, D-SUB 9P, FEMALE
IC6 8-759-050-06 s IC SN74HC157APW-E05
IC7 8-759-049-76 s IC SN74HC244APW-E05
IC8 8-759-049-76 s IC SN74HC244APW-E05
FB1 1-543-775-11 s FILTER, EMI
FB2 1-543-775-11 s FILTER, EMI
FB3 1-543-775-11 s FILTER, EMI
L1 1-412-026-11 s INDUCTOR CHIP 1uH
L2 1-412-026-11 s INDUCTOR CHIP 1uH
FB4 1-543-775-11 s FILTER, EMI
FB5 1-543-775-11 s FILTER, EMI
L3 1-412-026-11 s INDUCTOR CHIP 1uH
L4 1-412-026-11 s INDUCTOR CHIP 1uH
L5 1-410-381-11 s INDUCTOR, CHIP 10uH
FB6 1-543-775-11 s FILTER, EMI
FB7 1-543-775-11 s FILTER, EMI
FB8 1-543-775-11 s FILTER, EMI
R1 1-218-740-11 s METAL, CHIP 100K 0.50% 1/16W
FB9 1-543-775-11 s FILTER, EMI
R2 1-218-740-11 s METAL, CHIP 100K 0.50% 1/16W
R3 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R4 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R5 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
IC1 8-759-049-70 s IC SN74HC138APW-E05
IC2 8-759-050-06 s IC SN74HC157APW-E05
IC3 8-759-050-06 s IC SN74HC157APW-E05
IC4 8-759-050-06 s IC SN74HC157APW-E05
R6 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
IC5 8-759-049-76 s IC SN74HC244APW-E05
R7 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R8 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R9 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
IC6 8-759-049-76 s IC SN74HC244APW-E05
IC7 8-759-054-56 s IC SN75179BPS
R10 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
L1 1-412-026-11 s INDUCTOR CHIP 1uH
R11 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R12 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
L2 1-412-026-11 s INDUCTOR CHIP 1uH
L3 1-412-026-11 s INDUCTOR CHIP 1uH
L4 1-410-381-11 s INDUCTOR, CHIP 10uH
RB1 1-236-904-11 s NETWORK RESISTOR (CHIP) 1.0K
RB2 1-236-904-11 s NETWORK RESISTOR (CHIP) 1.0K
RB3 1-236-904-11 s NETWORK RESISTOR (CHIP) 1.0K
RB4 1-239-308-11 s RESISTOR BLOCK, CHIP 47kx8
R1 1-218-740-11 s METAL, CHIP 100K 0.50% 1/16W
R2 1-218-740-11 s METAL, CHIP 100K 0.50% 1/16W
R3 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R4 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
S1 1-571-967-11 s SWITCH, DIP 8-CKT
R5 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
2-2
R6 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R7 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R8 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R9 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R10 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R11 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R12 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R13 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R14 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R15 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R16 1-218-732-11 s METAL, CHIP 47K 0.50% 1/16W
R17 1-211-969-11 s METAL, CHIP 10 0.50% 1/16W
R18 1-211-969-11 s METAL, CHIP 10 0.50% 1/16W
R19 1-218-724-11 s METAL, CHIP 22K 0.50% 1/16W
R20 1-218-724-11 s METAL, CHIP 22K 0.50% 1/16W
R21 1-218-700-11 s METAL, CHIP 2.2K 0.50% 1/16W
HKCF-700
Page 17
(IF-625 BOARD)
Ref. No.
or Q’ty Part No. SP Description
---- FRAME
---- Ref. No.
or Q’ty Part No. SP Description
R22 1-218-700-11 s METAL, CHIP 2.2K 0.50% 1/16W
R23 1-218-668-11 s METAL, CHIP 100 0.50% 1/16W
R24 1-216-864-11 s METAL, CHIP 0
RB1 1-236-904-11 s NETWORK RESISTOR (CHIP) 1.0K
RB2 1-236-904-11 s NETWORK RESISTOR (CHIP) 1.0K
RB3 1-236-904-11 s NETWORK RESISTOR (CHIP) 1.0K
CNU-700
1pc 1-774-837-11 s CONNECTOR, D-SUB 15P, MALE
1pc 3-603-243-01 o PANEL, HKCF
2pcs 3-711-228-01 o STANDOFF, D-SUB CONNECTOR
CN12(to MB-562 board)
1-580-591-11 o HOUSING, 30P
1-580-599-11 o CONTACT, FEMALE AWG22-30
CN14(to MB-562 board)
1-580-582-11 o HOUSING, 12P
1-580-599-11 o CONTACT, FEMALE AWG22-30
CN15(to CN-1001 board)
1-580-591-11 o HOUSING, 30P
1-580-599-11 o CONTACT, FEMALE AWG22-30
CNU-500
CN6(to IF-625 board)
1-695-214-11 o HOUSING, 15P
1-695-215-11 o CONTACT, FEMALE AWG26-30
CN9(to AT-100 board)
1-695-214-11 o HOUSING, 15P
1-695-215-11 o CONTACT, FEMALE AWG26-30
HKCF-700
2-3
Page 18
2-3. Supplied Accessories
Ref. No.
or Q'ty Part No. SP Description
1pc 1-956-085-11 o SUB HARNESS (CNU-500)
1pc 1-956-086-11 o SUB HARNESS (CNU-700)
1pc 1-956-323-11 o HARNESS (RS422)
1pc 3-200-199-01 o PC BOARD SPACER
2-4
HKCF-700
Page 19
IC
C-MOS 3-TO-8 LINE DECODER / DEMULTIPLEXER
—TOP VIEW—
EN
0
1
1
1
1
1
1
1
1
Y7
1
1
1
1
1
1
1
1
0
Y6
1
1
1
1
1
1
1
0
1
Y5
1
1
1
1
1
1
0
1
1
Y4
1
1
1
1
1
0
1
1
1
Y3
1
1
1
1
0
1
1
1
1
Y2
1
1
1
0
1
1
1
1
1
Y1
1
1
0
1
1
1
1
1
1
Y0
1
0
1
1
1
1
1
1
1
C
X
0
0
0
0
1
1
1
1
B
X
0
0
1
1
0
0
1
1
A
X
0
1
0
1
0
1
0
1
V
DD
IN
IN
IN
IN
IN
IN
OUT
INPUTS OUTPUTS
1
2
3
4
5
6
7
A
B
C
EN1
EN2
EN3
Y7
8
10
11
12
13
14
15
16
9
0 ; LOW LEVEL
1 ; HIGH LEVEL
X ; DON'T CARE
EN = EN1 • EN2 • EN3
GND
OUT
4
1
2
3
15
14
13
A
B
C
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
EN
5
6
EN1
EN2
EN3
Y0
OUT
Y1
OUT
Y2
OUT
Y3
OUT
Y4
OUT
Y5
OUT
Y6
12
11
10
9
7
TYPE
74HCT138 TYPE
74ACT138 TYPE
TC74AC138 TYPE
TC74VHC138
OTHER TYPES
+2 to +5.5V
NOTE:
+2 to +6V
V
DD
+5V
+4.5 to +5.5V
IC
Section 3
Semiconductor Pin Assignments
Semiconductors of which functions are equivalent are described
here. For parts replacement, refer to the section of Spare Parts in
this manual. The circuit diagram of each IC is obtained from the
IC data book published by the manufacturer.
SN74HC157APW(TI)FLAT PACKAGE
SN74HC157APW-E05
C-MOS QUAD 2-LINE-TO-1-LINE DATA SELECTOR/ DEMULTIPLEXER
—TOP VIEW—
INH
INY0INY1INYCOUTX0INX1INXCOUT
14 13 12 11 10
16 15
V
DD
AINV0INV1INVC
NOTE:
OTHER TYPES
0
1
TYPE
74ACT/74FCT
TC74AC157P
TC74AC157
TC40H
1
0
0
1
OUTW0INW1INWCOUT
DD
V
+5V
+2 to +5.5V
+2 to +8V
+2 to +6V
SN74HC244APW-E05(TI)
C-MOS BUS BUFFER WITH 3-STATE OUTPUTS
—TOP VIEW—
G2
DD
V
G1
2
4
6
8
11
13
15
17
119
HKCF-700
G1
1617181920
18
16
14
12
9
OR
7
5
3
G2
1
0
GND
7654321
14 13 12 11
15
7654321
2
4
6
8
G
1
11
13
15
17
G
19
9
8
CONT.IN
INH
0
0
1
8 9 10
18
16
14
12
9
7
5
3
GND
A
0
1
X
CHANNEL
NOTE:
TC74AC244 TYPE
V0
2
V1
3
W0
5
W1
6
X0
11
10
X1
Y0
14
13
Y1
VC
WC
XC
YC
A INH
115
ON
0
0 ; LOW LEVEL
1
1 ; HIGH LEVEL
GND
X ; DON'T CARE
AY = YA
GG
G
A
Y
0
0
TYPE
AC
HC
40H
ACT
BCT
FCT
HCT
0
1
1
X
HI-Z
0
X
0 ; LOW LEVEL
1 ; HIGH LEVEL
X ; DON'T CARE
HI-Z ; HIGH IMPEDANCE
TC74VHC244
4
7
9
12
DD
V
+2 to +6V
+5V
+2 to +5.5V
SN75179BPS(TI)FLAT PACKAGE
SN75179BPS-E05
DIFFERENTIAL BUS DRIVER/RECEIVER
-TOP VIEW-
VCC
1
2
R
3
D
4
+
(
)
5V
GND
-DRIVERINPUT
D
HLHLL
OUTPUTS
YZ
8
A
7
B
6
Z
5
Y
H
2
R
3
D
-RECEIVERDIFFERENTIAL INPUTS
V
–0.2V < V
ID –0.2V
V
A–B
ID 0.2V
ID
<
H = HIGH LEVEL L = LOW LEVEL ? = INDETERMINATE
SN74HC138APW-E05(TI)FLAT PACKAGE
SN74HC138APW-E05
8
7
6
5
0.2V
A
B
Z
Y
OUTPUTS
R
H
?
L
3-1
Page 20
IC
M27C4001-12F1(SGS) M27C4002-12F1(SGS)
C-MOS 4M-BIT UV EPROM
-TOP VIEW-
1
V
PP
GND
(+5V)
PINS
A9OECE
V
0
x
x
1
x
x
x
x
x
1
x
V
V
0
x
V
1
x
V
0
+12V
IN
A16
2
IN
A15
3
IN
A12
4
IN
A7
5
IN
A6
6
IN
A5
7
IN
A4
8
IN
A3
9
IN
A2
10
IN
A1
11
IN
A0
12
I/O
O0
13
I/O
O1
14
I/O
O2
15
16
0
0
1
0
1
1
0
INDENTIFIER
MANUFACTURER CODE
DEVICE CODE
12
A0
32
DD
V
IN
A18
31
IN
A17
30
IN
A14
29
IN
A13
28
IN
A8
27
IN
A9
26
IN
A11
25
IN
OE
24
IN
A10
23
IN
22
CE
I/O
O7
21
I/O
O6
20
I/O
O5
19
I/O
O4
18
I/O
O3
17
O0-O7
PP
D
OUT
HI-Z
HI-Z
D
IN
PP
D
OUT
PP
HI-Z
PP
CODE
PP
A0
O7 O6 O5 O4 O3 O2 O1 O0
00010000020
10100000141
11
A1
10
A2
9
A3
8
A4
7
A5
6
A6
5
A7
27
A8
26
A9
23
A10
25
A11
4
A12
28
A13
29
A14
3
A15
2
A16
30
A17
31
A18
CE V
22 24 1
A0-A19;ADDRESS INPUTS
CE ;CHIP ENABLE INPUT
O0-O7 ;DATA INPUTS/OUTPUTS
OE ;OUTPUT ENABLE INPUT
V
;PROGRAMMING VOLTAGE INPUT
PP
(+12.75V)
MODE
READ
OUTPUT DISABLE
STAND BY
PROGRAM
PROGRAM VERIFY
PROGRAM INHIBIT
ELECTRONIC SIGNATURE
CODE DATA
13
O0
14
O1
15
O2
17
O3
18
O4
19
O5
20
O6
21
O7
OE
PP
0 ;LOW LEVEL
1 ;HIGH LEVEL
X ;DON'T CARE
HI-Z;HIGH IMPEDANCE
C-MOS 4M(256kx16)-BIT UV EPROM
-TOP VIEW-
1
VV
PP
IN
2
CE
OUT
3
D15
OUT
4
D14
OUT
5
D13
OUT
6
D12
OUT
7
D11
OUT
8
D10
OUT
9
D9
OUT
10
D8
11
GND GND
OUT
12
D7
OUT
13
D6
OUT
14
D5
OUT
15
D4
OUT
16
D3
OUT
17
D2
OUT
18
D1
OUT
19
D0
IN
20
OE
V
ADDRESS
INPUTS
A17
PP
CE
OE
A0
A8
A9
40
DD
(+5V)
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
1
2
CE OE,
AND PROGRAM
20
21
29
DECODER
30
DECODER
39
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
LOGIC
Y
X
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
21
A0
22
23
24
25
26
27
28
29
31
32
33
34
35
36
37
38
39
A0-A17
CE
D0-D15
OE
V
PP
DATA OUTPUTS
19 1012 3
BUFFERS
CELL MATRIX
4194.304
D0
A1
D1
A2
D2
A3
D3
A4
D4
A5
D5
A6
D6
A7
D7
A8
D8
A9
D9
A10
D10
A11
D11
A12
D12
A13
D13
A14
D14
A15
D15
A16
A17
CE OE
220
;ADDRESS INPUTS
;CHIP ENABLE
;DATA OUTPUTS
;OUTPUT ENABLE
;PROGRAMMING VOLTAGE
(PROGRAM :+12.75V)
D0-D15
OUTPUT
Y
GATING
19
18
17
16
15
14
13
12
10
9
8
7
6
5
4
3
A0-A18
24
OE
22
CE
12-5
27,26
23,25
4,28
29,3,2
30,31
3-2
OUTPUT ENABLE
CHIP ENABLE
AND
PROGRAM LOGIC
Y
DECODER
X
DECODER
OUTPUT
BUFFERS
Y
GATING
4,194,304
CELL MATRIX
13-15
17-21
O0-O7
ABOVE DIAGRAM SHOWS CONDITIONS BEFORE PROGRAMMING.
CE OE A9 OUTPUT FUNCTION
0
0
0
1
1
1
0
1
0
x
HI-Z
V
H
0
1
1
0
1
xx
0
;HIGH LEVEL
;LOW LEVEL
;DON'T CARE
;
HIGH IMPEDANCE
;
12.0±0.5V
V
xx
x
x
x
x
H
PP
x
V
PP
V
PP
V
PP
x
VV
DD
OUT
D
HI-Z
IN
D
OUT
D
HI-Z
HI-Z
CODE
READ
OUTPUT DISABLE
PROGRAM
VERIFY
PROGRAM INHIBIT
STANDBY
ELECTRONIC SIGNATURE
HKCF-700
Page 21
TC7W04FU(TOSHIBA)CHIP PACKAGE
TC7W04FU(TE12R)
C-MOS HEX INVERTERS
(SCALE 3/1)
—TOP VIEW—
DD(+2 to +6V)
8 V
GND 4
1
2
7
3
6
5
17
AA
Y =
35
62
A
Y
0
1
1
0
0 ; LOW LEVEL
1 ; HIGH LEVEL
UPD71055GB-10-3B4(NEC)FLAT PACKAGE
C-MOS PARALLEL INTERFACE UNIT
—TOP VIEW—
RD
P00
P01
P02
P03
P04
P05
P06
P07
44 43 42 41 40 39 38 37 36 35 34
INDEX
NC
1
2
CS
3
4
GND
A1
5
A0
6
P27
7
P26
8
P25
9
P24
10
P20
11
P21
12 13 14 15 16 17 18 19 20 21 22
P22
P23
P10
P11
;
ADDRESS
A1, A0
;
CHIP SELECT
CS
;
DATA BUS
D7-D0
;
PORT 0
P07-P00
;
INTERNALLY CONNECTED
IC
CS
RD
WR
0
0
0
0
0
0
0
0
0
0
1
A1
0
1
0
0
1
0
0
1
1
0
1
1
0
0
X
1
0
0
1
0
0
1
0
1
1
0
1
1
1
X
X
X
X
IC
P12
A0
0
1
0
1
X
0
1
0
1
X
X
WR
NC
NC
33
RESET
32
31
D0
D1
30
29
D2
D3
28
27
D4
D5
26
25
D6
D7
24
23
VDD
(+5V)
P13
P14
P15
P16
P17
P17-P10
;
P27-P20
;
RD
;
WR
;
OPERATION
PORT0 DATA • BUS
PORT1 DATA • BUS
PORT2 DATA • BUS
DISABLE
DATA • BUS PORT0
DATA • BUS PORT1
DATA • BUS PORT2
DATA • BUS COMMAND REGISTER
HIGH IMPEDANCE
Y
Y = A
PORT 1
PORT 2
READ STROBE
WRITE STROBE
CPU ACTION
INPUT
INPUT
INPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
2
CS
5
A0
4
A1
35
WR
44
RD
24
D7
25
D6
26
D5
27
D4
28
D3
29
D2
30
D1
31
D0
32
RESET
0 ; LOW LEVEL
1 ; HIGH LEVEL
X ; DON'T CARE
IC
43
P00
42
P01
41
P02
40
P03
39
P04
38
P05
37
P06
36
P07
14
P10
15
P11
16
P12
18
P13
19
P14
20
P15
21
P16
22
P17
10
P20
11
P21
12
P22
13
P23
9
P24
8
P25
7
P26
6
P27
24-31
D7-D0
44
RD
35
WR
4
A1
5
A0
32
RESET
2
CS
HKCF-700
DATA BUS
BUFF
READ/
WRITE
CONTROL
8
GROUP
CONTROL
COMMAND
REGISTER
GROUP
CONTROL
8
PORT 0
8
PORT 2
8
INTERNAL 8-BIT BUS
PORT 1
36-43
13-10
22-18,
16-14
P07-P00
6-9
P27-P24
P23-P20
P17-P10
3-3
Page 22
Page 23
Section 4
Schematic Diagrams
1
2
3
4
5
HKCF-700
EFGH
4-1
Page 24
IF-624
1
HKCF-700
CN1
A2 IN
A1
A4 IN
A2
A6 IN
A3
A8 IN
A4
A10 IN
A5
A12 IN
A6
A14 IN
A7
A16 IN
A8
A18 IN
A9
A20 IN
A10
D0 IN
A11
D2 IN
A12
D4 IN
2
AT-89,CN1
3
AT-89,CN2
4
A13
A14
A15
B10
B11
B12
B13
B14
B15
CN2
A10
A11
A12
A13
A14
A15
B10
B11
B12
B13
B14
B15
B1
B2
B3
B4
B5
B6
B7
B8
B9
A1
A2
A3
A4
A5
A6
A7
A8
A9
B1
B2
B3
B4
B5
B6
B7
B8
B9
D6 IN
GND
A3 IN
A5 IN
A7 IN
A9 IN
A11 IN
A13 IN
A15 IN
A17 IN
A19 IN
A21 IN
D1 IN
D3 IN
D5 IN
D7 IN
GND
+5V
RESET-N
RDEN
BOARD2-CS
OUTA14 OUT
OUTA16 OUT
NC
NC
GND
B/A
SPARE4
CH2 ON
CH3 ON
RECALL1
TWO/ONE
+5V
WREN
SPA-CS0
SPA-INT
OUTA15 OUT
OUTA17 OUT
INB07 OUT
NC
GND
THREE
GND
STORE
RECALL0
CH1 ON
BOTH
ADRS2
ADRS3
L5
10µH C6
RECALL1
TWO/ONE
WFM STORE
RECALL0
DATA0
DATA2
DATA4
DATA6
DATA1
DATA3
DATA5
DATA7
B/A
CH2 ON
CH3 ON
THREE
CH1 ON
BOTH
10V
:TA
THREE
CH1 ON
CH2 ON
CH3 ON
ANA/SDI
TWO/ONE
WFM STORE
5V
L1
1µH
C1
0.1
TP1
IC2(1/3)
TC7W04FU(TE12R)
5V
8
17
2
22
E1
4
5V
S1
1615
13
11
9
7
5
3
1
14
12
10
8
6
4
2
0.1
ADRS3
ADRS2
MODE SW7
MODE SW6
RB4
:47K
MODE SW5
MODE SW4
MODE SW0
MODE SW1
56473829
MODE SW7
MODE SW6
MODE SW5
MODE SW4
MODE SW3
MODE SW2
MODE SW1
MODE SW0
10
11
C2
1
P00
P01
RDP22
1
NC
2
CS
3
GND
4
A1
5
A0
6
P27
7
P26
8
P25
9
P24
P20
P21
P23
P10
12 1314 15 16 17 18 19 20 21 22
MODE SW2
MODE SW3
P10
P11
P03
P02
1
P11
P12NCP13
P12
P04
P13
P05
P06
P14
P14
µPD71055GB-10-3B 4
3435363738394041424344
P07
NC
WR
NC
RESET
D0
D1
D2
D3
D4
D5
D6
D7
VDD
P15
P16
P17
PRESET-C
PRESET-B
PRESET-A
IC1
33
32
31
30
29
28
27
26
25
24
23
P07
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
5
4-2
HKCF-700
AB C D
Page 25
PRESET-A
PRESET-B
IC3
SN74HC138APW-E05
PRESET-A
PRESET-B
PRESET-C
1
A
2
B
3
C
6
G1
4
G2A
5
C3
G2B
0.1
25V
F
IC6(3/4)
SN74HC157APW-E05
IC6(1/4)
SN74HC157APW-E05
10
11
6
9
5
5V
L2
1µH
16
15
PRESET1
Y0
14
PRESET2
Y1
13
PRESET3
Y2
12
PRESET4
Y3
3
PRESET5
11
Y4
10
PRESET6
Y5
9
PRESET7
Y6
PRESET8
7
Y7
8
IC6(2/4)
SN74HC157APW-E05
13
7
14
666
1
ANA/SDI
12
TWO/ONE
IC4(1/4)
SN74HC157APW-E05
PRESET1
SN74HC157APW-E05
PRESET2
ANA/SDI
SN74HC157APW-E05
PRESET3
WFM STORE
SN74HC157APW-E05
PRESET4
THREE
SN74HC157APW-E05
PRESET5
CH1 ON
SN74HC157APW-E05
PRESET6
CH2 ON
SN74HC157APW-E05
PRESET7
CH3 ON
SN74HC157APW-E05
PRESET8
SN74HC157APW-E05
IC4(2/4)
IC4(4/4)
IC4(3/4)
IC5(1/4)
IC5(2/4)
IC5(4/4)
IC5(3/4)
IC6(4/4)
R1
100k
R2
100k
10
11
13
14
3
2
6
5
10
11
13
14
3
2
5V
6
5
3
2
1
15 8
15 8
IF-624
1
4
9
4
12
815
4
4
16
4
7
5
9
5
12
1
5
4
16
5
7
6
4
16
5V
C5
0.1
P10
P11
P12
P13
P14
P07
IC7
SN74HC244APW-E05
5V
0.1
C4
L3
1µH
20
VCC
2
4
7
6
8
13
15
17
GND
G1 G2
1
19 10
5V
L4
1µH
20
VCC
2
4
8
6
8
13
15
17
G1 G2
GND
1
19 10
IC8
SN74HC244APW-E05
18
16
14
12
911
7
5
3
18
16
14
12
911
7
5
3
R3
47kR447kR547kR647kR747kR847kR947k
R10
47k
R11
47k
R12
47k
5V
RB1
12
:1K
34
56
78
RB2
12
:1K
34
56
78
RB3
12
:1K
34
56
78
IC2(2/3)
TC7W04FU(TE12R)
35
TC7W04FU(TE12R)
62
WFM STORE
2
IC2(3/3)
2
TWO/ONE
RECALL0
RECALL1
THREE
CH1 ON
CH2 ON
CH3 ON
B/A
BOTH
2
3
4
IF-624
BOARD NO. 1-660-092-11/12
LOT NO. 512-
B-¥HKCF700-IF624-11
5
HKCF-700
EFGH
4-3
Page 26
IF-625
1
2
3
4
5
HKCF-700
AT-100,CN9
CN6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ANA/SDI
WFM STORE
TWO/ONE
THREE
CH3 ON
CH2 ON
CH1 ON
PRESET-A
PRESET-B
PRESET-C
OUT06
CART+ TX
CART+ RX
+5V
GND
ANA/SDI
WFM STORE
TWO/ONE
THREE
CH3 ON
CH2 ON
CH1 ON
L4
10µH
C4
22
10V
IC4(1/4)
SN74HC157APW-E05
10
11
5V
L1
1µH
1
A
2
B
3
C
1
6
G1
4
G2A
5
C1
G2B
0.1
25V
F
IC4(3/4)
SN74HC157APW-E05
6
9
5
IC1
SN74HC138APW-E05
16
15
PRESET1
Y0
14
PRESET2
Y1
13
PRESET3
Y2
12
PRESET4
Y3
PRESET5
11
Y4
10
PRESET6
Y5
9
PRESET7
Y6
PRESET8
7
Y7
8
IC4(2/4)
SN74HC157APW-E05
444
13
7
14
1
ANA/SDI
TWO/ONE
PRESET1
PRESET2
ANA/SDI
PRESET3
WFM STORE
SN74HC157APW-E05
PRESET4
THREE
PRESET5
CH1 ON
PRESET6
CH2 ON
PRESET7
CH3 ON
SN74HC157APW-E05
PRESET8
12
SN74HC157APW-E05
IC2(1/4)
SN74HC157APW-E05
IC2(2/4)
SN74HC157APW-E05
IC2(4/4)
SN74HC157APW-E05
2
10
11
2
13
14
1
2
3
2
IC2(3/4)
2
6
5
IC3(1/4)
SN74HC157APW-E05
IC3(2/4)
SN74HC157APW-E05
IC3(4/4)
SN74HC157APW-E05
IC3(3/4)
IC4(4/4)
R1
100k
3
10
11
3
13
14
15 8
3
3
2
5V
3
6
5
15 8
4
3
2
R2
100k
9
12
815
4
16
7
9
12
1
4
16
7
4
5V
16
4-4
HKCF-700
AB C D
Page 27
IF-625
AT-100,CN1
AT-100,CN8
IC5
SN74HC244APW-E05
5V
C2
0.1
VCC
2
4
6
8
13
15
17
G1 G2
1
5V
C3
0.1
VCC
2
4
6
8
13
15
17
G1 G2
1
IC6
SN74HC244APW-E05
20
5
19 10
20
6
19 10
L2
1µH
GND
L3
1µH
GND
CN1
13P
13
12
11
10
9
8
7
6
5
4
3
2
1
18
16
14
12
911
7
5
3
18
16
14
12
911
7
5
3
REF.VIDEO(X)IN
REF.VIDEO(Y)IN
Character(X)OUT
Character(Y)OUT
GND
TXD
DTR
RTS
DCD
RXD
DSR
CTS
SG
R6
47kR547kR447kR347kR747k
IC7(2/2)
SN75179BPS-E05
3
7
2
CN3
REFERENCE
FB1
CN4
REFERENCE
DCD
RXD
TXD
DTR
SG
DSR
RTS
CTS
CN5
CHARACTER OUT
CN2
9PF
1
2
3
4
5
6
7
8
9
CN2
RS232C
FB2
FB3
FB4
FB5
FB6
FB7
FB8
FB9
R12
R11
R10
R9
47kR847k
47k
47k
47k
5V
R15
47k
R13
47k
R16
47k
R14
47k
1
2
3
D-SUB 15PIN CN
CN7
10
11
12
13
14
15
1
2
3
4
5
6
7
8
9
CN7
WF-MODE
RB1
12
:1K
34
56
78
78
RB2
:1K
34
56
12
RB3
12
:1K
34
56
78
FIELD/FRAME
FOUR
TWO/ONE
RMT SYNC ENB
RECALL1
WFM STORE
RECALL0
THREE
GND
RMT SYNC OUT
BOTH
CH1 ON
CH2 ON
CH3 ON
B/A
4
R17
10
6
5
R18
5V
10
R23
R19
C5
22k
0.1
1
7
7
8
4
22k
R21
2.2k
R22
2.2k
100
D-SUB 9PIN CN
NC
RX(Y)
TX(X)
NC
GND
NC
RX(X)
TX(Y)
R24
0R20
NC
CN8
1
2
3
4
5
6
7
8
9
CN8
RS422A
IC7(1/2)
SN75179BPS-E05
HKCF-700
IF-625
BOARD NO. 1-660-080-11
LOT NO. 512-
B-¥HKCF700-IF625-11
5
4-5
EFGH
Page 28
Page 29
Section 5
Board Layouts
IF-624
———————————————————————
IF-624(1-660-092-11,12)
———————————————————————
C1 B1
C2 B1
C3 A1
C4 A2
C5 A3
C6 B2
CN1 B1
CN2 B3
E1 B1
IC1 B1
IC2 B1
IC3 A2
IC4 A2
IC5 A3
IC6 A3
IC7 A2
IC8 A3
HDCF-700
L1 B1
L2 A1
L3 B2
L4 B3
L5 B2
R1 A3
R2 A3
R3 B3
R4 B3
R5 B3
R6 B3
R7 B3
R8 B3
R9 B2
R10 B2
R11 B2
R12 B2
RB1 B2
IF-624 -A SIDE-
1-660-092-11, 12
RB2 B3
RB3 B3
RB4 A1
S1 A1
TP1 B1
IF-624 -B SIDE-
1-660-092-11, 12
5-1
Page 30
IF-625
————————————————————
IF-625(1-660-080-11)
————————————————————
C1 C1
C2 B1
C3 A1
C4 C1
C5 C2
CN1 A2
CN2 *C2
CN3 *A1
CN4 *B1
CN5 *A2
CN6 C2
CN7 *C1
CN8 *C2
FB1 A1
FB2 A2
FB3 B2
FB4 B2
FB5 A2
FB6 A2
FB7 B2
FB8 B2
FB9 B2
IC1 C1
IC2 C1
IC3 C1
IC4 C1
IC5 B2
IC6 B2
IC7 C2
L1 C1
L2 B1
L3 B1
L4 C1
R1 C2
R2 C2
R3 B1
R4 B1
R5 C1
R6 C2
R7 C1
R8 C2
R9 C1
R10 C1
R11 C1
R12 C1
R13 C1
R14 C1
R15 C1
R16 C1
R17 C2
R18 C2
R19 C2
R20 C2
R21 C2
R22 C2
R23 C2
R24 C2
RB1 C1
RB2 C1
RB3 C1
*:B SIDE
IF-625 -A SIDE-
1-660-080-11
IF-625 -B SIDE-
1-660-080-11
5-2
HDCF-700
Page 31
The material contained in this manual consists of
information that is the property of Sony Corporation and
is intended solely for use by the purchasers of the
equipment described in this manual.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation et
sont destinées exclusivement à l’usage des acquéreurs
de l’équipement décrit dans ce manuel.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind,
und ausschließlich zum Gebrauch durch den Käufer der
in dieser Anleitung beschriebenen Ausrüstung bestimmt
sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
Page 32
HKCF-700 (UCJ) J, E
3-190-789-04
Printed in Japan
Sony Corporation 2001. 3 08
Communication System Solutions Network Company ©1996
Loading...