Sony HCDGZR-7-D, HCDGZR-8-D, HCDGZR-9-D Service manual

HCD-GZR7D/GZR8D/
GZR9D
SERVICE MANUAL
Ver. 1.1 2008.07
• HCD-GZR7D/GZR8D/GZR9D are the tuner, deck, DVD and amplifi er section in MHC-GZR7D/GZR8D/GZR9D.
Photo: HCD-GZR8D
DVD Section
Tape Deck Section
E Model
HCD-GZR7D/GZR8D/GZR9D
Australian Model
HCD-GZR9D
Russian Model
HCD-GZR7D/GZR9D
Model Name Using Similar Mechanism HCD-GNZ777D/GNZ888D DVD Mechanism Type CDM74HF-DVBU101//C Optical Pick-up Name KHM-313CAB/C2RP
Model Name Using Similar Machanism HCD-GNZ777D/GNZ888D
SPECIFICATIONS
Amplifi er Section
The following measured at AC 230 V, 50/60 Hz (Russian model) The following measured at AC 127, 220, 240 V, 50/60 Hz (Saudi Arabian model) The following measured at AC 120, 220, 240 V, 50/60 Hz (Other models)
MHC-GZR9D
Power output (rated): 100 W + 100 W (6 Ω at 1 kHz, 1% THD) RMS output power (reference) Front speaker: 180 W + 180 W (per channel at 6 Ω, 1 kHz, 10% THD) Center speaker: 60 W (6 Ω at 1 kHz, 10% THD) Surround speaker: 60 W + 60 W (per channel at 6 Ω, 1 kHz, 10% THD) Subwoofer: 180 W (6 Ω at 80 Hz, 10% THD)
MHC-GZR8D
Power output (rated): 100 W + 100 W (6 Ω at 1 kHz, 1% THD) RMS output power (reference) Front speaker: 180 W + 180 W (per channel at 6 Ω, 1 kHz, 10% THD) Center speaker: 60 W (6 Ω at 1 kHz, 10% THD) Surround speaker: 60 W + 60 W (per channel at 6 Ω, 1 kHz, 10% THD)
MHC-GZR7D
Power output (rated): 100 W + 100 W (6 Ω at 1 kHz, 1% THD) RMS output power (reference): 180 W+ 180 W (per channel at 6 Ω, 1 kHz, 10% THD)
Inputs
VIDEO/SAT VIDEO IN (phono jack): 1 Vp-p, 75 ohms VIDEO/SAT AUDIO IN L/R (phono jacks): voltage 250/450 mV, impedance 47 kilohms MIC 1/MIC 2 (phone jacks): sensitivity 1 mV, impedance 10 kilohms
– Continued on next page –
9-889-156-02
2008.07
©
DVD DECK RECEIVER
Sony Corporation
Audio&Video Business Group Published by Sony Techno Create Corporation
HCD-GZR7D/GZR8D/GZR9D
Ver. 1.1
Outputs
VIDEO OUT (phono jack): max. output level 1 Vp-p, unbalanced, Sync negative, load impedance 75 ohms S VIDEO OUT (4-pin/mini-DIN jack): Y: 1 Vp-p, unbalanced, Sync negative, C: 0.286 Vp-p, load impedance 75 ohms COMPONENT VIDEO OUT: Y: 1 Vp-p, 75 ohms PB/CB: 0.7 Vp-p, 75 ohms P DVD DIGITAL OUT (MHC-GZR7D only) (Square optical connector jack, rear panel): Wavelength 660 nm PHONES (stereo mini jack): accepts headphones of 8 ohms or more SUBWOOFER OUT (MHC-GZR8D/GZR7D only): Voltage 1 V, impedance 1 kilohms FRONT SPEAKER: MHC-GZR9D: Use only the supplied speaker SS-GZR9D. MHC-GZR8D/GZR7D: Use only the supplied speaker SS-GZR8D. SURROUND SPEAKER (MHC-GZR9D/GZR8D only): Use only the supplied speaker SS-RSX9D. CENTER SPEAKER (MHC-GZR9D/GZR8D only): Use only the supplied speaker SS-CTX9D. SUBWOOFER (MHC-GZR9D only): Use only the supplied subwoofer SS-WGV9D.
R/CR: 0.7 Vp-p, 75 ohms
USB section
Supported bit rate MP3 (MPEG 1 Audio Layer-3): 32 – 320 kbps WMA: 48 – 192 kbps AAC: 48 – 320 kbps Sampling frequencies MP3 (MPEG 1 Audio Layer-3): 32/44.1/48 kHz WMA: 44.1 kHz AAC: 44.1 kHz
(USB) port: Maximum current: 500 mA
Disc player section
System: Compact disc and digital audio and video system Laser Diode Properties Emission duration: Continuous Laser Output*: Less than 44.6μW *This output is the value measurement at a distance of 200mm from the objective lens surface on the Optical Pick-up Block with 7mm aperture. Frequency response DVD (PCM 48 kHz): 2 Hz – 22 kHz (±1 dB) CD: 2 Hz – 20 kHz (±0.5 dB) Video color system format Russian model: PAL Latin American model: NTSC Other models: NTSC and PAL
Tape deck section
Recording system: 4-track 2-channel, stereo
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range: 87.5 – 108.0 MHz (50 kHz step) Antenna: FM lead antenna Antenna terminals: 75 Ω unbalanced Intermediate frequency:
10.7 MHz
AM tuner section
Tuning range: Russian and Saudi Arabian models: 531 – 1,602 kHz (9 kHz step) Latin American model: 530 – 1,710 kHz (with 10 kHz tuning interval) 531 – 1,710 kHz (with 9 kHz tuning interval) Australian model: 531 – 1,710 kHz (with 9 kHz tuning interval) 530 – 1,710 kHz (with 10 kHz tuning interval) Other models: 531 – 1,602 kHz (with 9 kHz tuning interval) 530 – 1,610 kHz (with 10 kHz tuning interval) Antenna: AM loop antenna Antenna terminals: External antenna terminal Intermediate frequency: 450 kHz
General
Power requirements Russian model: AC 230 V, 50/60Hz Australian model: AC 230 – 240 V, 50/60 Hz Thai model: AC 220 V, 50/60 Hz Saudi Arabian model: AC 120 – 127, 220, 230–240 V, 50/60 Hz, adjustable with voltage selector Other models: AC 120, 220, 230 – 240 V, 50/60 Hz, adjustable with voltage selector Power consumption MHC-GZR9D: 270 W (Russian model: 0.5 W in Power Saving Model) MHC-GZR8D: 240 W MHC-GZR7D: 170 W (Russian model: 0.5 W in Power Saving Model) Dimensions (w/h/d) (excl. speakers) MHC-GZR9D: Approx. 280 × 325 × 415 mm MHC-GZR8D/GZR7D: Approx. 280 × 325 × 382 mm Mass (excl. speakers) MHC-GZR9D: Approx. 12 kg MHC-GZR8D: Approx. 11.5 kg MHC-GZR7D: Approx. 10.5 kg
Design and specifi cations are subject to change without notice.
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
HCD-GZR7D/GZR8D/GZR9D
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam­aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead­free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C. Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc refl ective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
This appliance is classifi ed as a CLASS 1 LASER product. This marking is located on the rear exterior.
CAUTION
Use of controls or adjustments or performance of procedures other than those specifi ed herein may result in hazardous radia- tion exposure.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostat­ic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The fl exible board is easily damaged and should be handled with care.
3
HCD-GZR7D/GZR8D/GZR9D
Ver. 1.1
MODEL IDENTIFICATION – Back Panel –
Parts No.
GZR9D: RU GZR9D: E3, E15 GZR9D: EA GZR9D: SP GZR9D: PH GZR9D: E2 GZR9D: AUS GZR9D: AR GZR8D: E3, E15 GZR8D: EA GZR8D: E12 GZR8D: SP GZR8D: TH GZR8D: PH GZR7D: RU GZR7D: E3, E15 GZR7D: EA GZR7D: E12 GZR7D: SP GZR7D: TH GZR7D: PH
Model Parts No.
3-285-875-0[] 3-285-875-1[] 3-285-875-2[] 3-285-875-4[] 3-285-875-6[] 3-285-875-7[] 3-285-875-8[] 3-285-875-9[] 3-291-798-1[] 3-291-798-2[] 3-291-798-3[] 3-291-798-4[] 3-291-798-5[] 3-291-798-6[] 3-291-799-0[] 3-291-799-1[] 3-291-799-2[] 3-291-799-3[] 3-291-799-4[] 3-291-799-5[] 3-291-799-6[]
• Abbreviation RU : Russian model E3 : 240V AC area in E model E15 : Iran model EA : Saudi Arabia model SP : Singapore model TH : Thai model PH : Philippines model E2 : 120V AC area in E model AUS : Australian model AR : Argentina model E12 : 220 – 240V AC area in E model
4

TABLE OF CONTENTS

HCD-GZR7D/GZR8D/GZR9D
Ver. 1.1
1. SERVICING NOTES ............................................. 6
2. GENERAL
Guide to parts and controls ............................................. 8
3. DISASSEMBLY
3-1. Case ................................................................................. 20
3-2. Loading Panel ................................................................. 20
3-3. Tuner Pack, DMPORT Board ......................................... 21
3-4. DVD Block Section ........................................................ 21
3-5. Front Panel Section ......................................................... 22
3-6. SUB-TRANS Board ....................................................... 22
3-7. Back Panel Section ......................................................... 23
3-8. Boards Section ................................................................ 23
3-9. SURR & CENT AMP Board
(HCD-GZR8D/GZR9D) ................................................. 24
3-10. MAIN Board ................................................................... 24
3-11. REGULATOR Board ...................................................... 25
3-12. AMP FR & SW Board .................................................... 25
3-13. Tape Mechanism Deck .................................................... 26
3-14. MIC Board, HEADPHONE Board ................................. 26
3-15. Lid (TC-L), Lid (TC-R) .................................................. 27
3-16. PANEL Board, VOLUME Board,
KEY-RIGHT Board ........................................................ 27
3-17. USB Board ...................................................................... 28
3-18. KEY-LEFT Board ........................................................... 28
3-19. VIDEO Board ................................................................. 29
3-20. DMB18 Board ................................................................. 29
3-21. DVD Assy ....................................................................... 30
3-22. Optical Pick-up ............................................................... 30
3-23. DRIVER Board, SW Board ............................................ 31
3-24. SENSOR Board .............................................................. 31
3-25. MOTOR (TB) Board....................................................... 32
3-26. MOTOR (LD) Board ...................................................... 32
7-6. Printed Wiring Boards –Driver Section– ........................ 49
7-7. Schematic Diagram –Driver Section– ............................ 50
7-8. Printed Wiring Board –DMB18 Board (1/2)– ................ 51
7-9. Printed Wiring Board –DMB18 Board (2/2)– ................ 52
7-10. Schematic Diagram –DMB18 Board (1/5)– ................... 53
7-11. Schematic Diagram –DMB18 Board (2/5)– ................... 54
7-12. Schematic Diagram –DMB18 Board (3/5)– ................... 55
7-13. Schematic Diagram –DMB18 Board (4/5)– ................... 56
7-14. Schematic Diagram –DMB18 Board (5/5)– ................... 57
7-15. Printed Wiring Board –Main Section– ............................ 58
7-16. Schematic Diagram –Main Section (1/4)– ...................... 59
7-17. Schematic Diagram –Main Section (2/4)– ...................... 60
7-18. Schematic Diagram –Main Section (3/4)– ...................... 61
7-19. Schematic Diagram –Main Section (4/4)– ...................... 62
7-20. Printed Wiring Boards –Mic/Headphone Section– ......... 63
7-21. Schematic Diagram –Mic/Headphone Section– ............. 64
7-22. Printed Wiring Board –TC Section– ............................... 65
7-23. Schematic Diagram –TC Section– .................................. 66
7-24. Printed Wiring Board –Video Section–........................... 67
7-25. Schematic Diagram –Video Section– ............................. 68
7-26. Printed Wiring Board –DMPORT Section– .................... 69
7-27. Schematic Diagram –DMPORT Section– ...................... 70
7-28. Printed Wiring Boards –Regulator/USB Section– .......... 71
7-29. Schematic Diagram –Regulator/USB Section– .............. 72
7-30. Printed Wiring Boards –Panel Section– .......................... 73
7-31. Schematic Diagram –Panel Section– .............................. 74
7-32. Printed Wiring Boards –Front Speaker Section– ............ 75
7-33. Schematic Diagram –Front Speaker Section– ................ 76
7-34. Printed Wiring Boards –Surround/Center Speaker,
Subwoofer Section– (HCD-GZR8D/GZR9D) ................ 77
7-35. Schematic Diagram –Surround/Center Speaker,
Subwoofer Section– (HCD-GZR8D/GZR9D) ................ 78
7-36. Printed Wiring Boards –Power Section– ........................ 79
7-37. Schematic Diagram –Power Section– ............................. 80
4. TEST MODE ............................................................ 33
5. MECHANICAL ADJUSTMENTS ...................... 38
6. ELECTRICAL ADJUSTMENTS ........................ 39
7. DIAGRAMS
7-1. Block Diagram –RF/Servo Section– ............................... 43
7-2. Block Diagram –Video Section– .................................... 44
7-3. Block Diagram –Main Section– ..................................... 45
7-4. Block Diagram –Audio Section– .................................... 46
7-5. Block Diagram –Display/Power Section– ...................... 47
8. EXPLODED VIEWS
8-1. Overall Section ............................................................... 93
8-2. Front Panel Section-1 ...................................................... 94
8-3. Front Panel Section-2 ...................................................... 95
8-4. Back Panel Section ......................................................... 96
8-5. Chassis Section-1 ............................................................ 97
8-6. Chassis Section-2 ............................................................ 98
8-7. DVD Block Section ........................................................ 99
8-8. DVD Mechanism Deck Section-1 .................................. 100
8-9. DVD Mechanism Deck Section-2 .................................. 101
9. ELECTRICAL PARTS LIST .............................. 102
5
HCD-GZR7D/GZR8D/GZR9D
SECTION 1

SERVICING NOTES

Notes on Disconnecting Between the OP Section (DVBU101) and the DMB18 Board
Note: When disconnecting between the OP section (DVBU101) and the DMB18 board, be sure to make a solder brige for electrostatic
prevention as illustrated in the fi gure (before disconnection). On the contrary, when installing the OP section, never remove the solder bride until the OP section and the DMB18 board are connected. Be sure to remove the solder bridge after the OP section and the DMB18 board have been connected.
Perform solder bridging to prevent damage by electrostatic discharge when handling the BU as a single unit.
Service Position for the DVD Mechanism Deck Section
Refer to the fi gure given below when disassembling the DVD mechanism deck section.
DMB18 board
DVD mechanism deck section
6
HCD-GZR7D/GZR8D/GZR9D
Notes on Installing the Two Cooling Fans (FAN901 and FAN902) (HCD-GZR8D/GZR9D)
Note: The HCD-GZR8D/GZR9D has two cooling fans (FAN901 and FAN902) used. The connectors of these fans have the same color
and the same number of pins. When installing these fans, check the marking of CN601 and CN602 on the MAIN board and ensure that they are located correctly. The CN601 on the MAIN board is to be attached with the connector of FAN901 where as the CN602 is to be attached with the
connector of FAN902.
back panel
FAN901
FAN902
CN601
MAIN board
CN602
7
HCD-GZR7D/GZR8D/GZR9D

Guide to parts and controls

also be performed using the buttons on the unit having the same or similar names.
Unit
SECTION 2

GENERAL

This section is extracted from instruction manual.
GB
12
8
HCD-GZR7D/GZR8D/GZR9D
Remote
@/ (on/standby) (24, 79, 106,
129)
Unit: STANDBY indicator (118)
Remote: TV @/
1)
(on/standby)
(29)
DISPLAY (27, 33, 73, 107, 108)
Press to display the disc information or clock in the front panel display.
Unit: ILLUMINATION (108, 129)
Press to change the illumination pattern around MASTER VOLUME0.
Display
Disc tray
Remote sensor
Guide to parts and controls
Continued
M
13
GB
9
HCD-GZR7D/GZR8D/GZR9D
ENTER (28, 33, 34, 39, 44, 49, 53, 58, 59, 60, 63, 71, 74, 76, 79, 83, 87, 95, 102, 105, 129)
Press to enter the settings.
SOUND FIELD (95)
surround sound.
Unit: GROOVE (94)
Press to reinforce the bass.
Unit: PRESET EQ (94)
Unit: EQ BAND/MEMORY (95)
Press to select the frequency band when adjusting the equalizer.
REC TO USB (79, 83)
Press to transfer music from a disc or record the sound from an analog audio source to the connected optional USB device. Press to mark track numbers during recording.
OPTIONS (74, 75, 107, 116)
Press to enter the option menus.
+
Unit: ; OPEN/CLOSE (38)
Press to load or eject a disc.
Unit: DISC SKIP/EX-CHANGE (38,
40)
Press to select a disc. Press to exchange a disc while playing.
Remote: DISC SKIP (40, 79)
Press to select a disc.
Unit: DISC 1 – DISC 3 (40, 76, 79)
Press to select a disc. Press to switch to the “DVD” function from other function.
,
; PUSH/PUSH ; (74)
Press to insert or eject a tape.
-
Unit: O/ (play) (26, 38, 74, 87) Remote: )
Press to start playback.
2)
(play) (38, 74, 87)
REC TOTAPE (76)
Press to record on a tape.
GB
14
9 (pause) (27, 39, 75)
Presstopauseplayback.
10
HCD-GZR7D/GZR8D/GZR9D
Y (stop) (39, 72, 75, 79)
Presstostopplayback.
N/. (rewind/fast forward) (39, 75)
Unit: / (39) Remote:
Press to watch the slow-motion play.
SLOW/ SLOW (39)
TUNING +/– (71, 72, 73)
Press to tune in the desired station.
Remote: +/– (36, 39)
Press to select a folder.
Unit: OPERATION DIAL (39, 72, 74, 76, 95, 107)
Turn to select a track, chapter or video
Turn to select the preset station.
Remote: PRESET +/– (72)
Press to select the preset station.
Remote: / (go backward/forward) (35, 37, 39, 74, 88)
Press to select a track, chapter or video
.
MIC 1/MIC 2 jacks (77, 98)
Connect a microphone.
MIC 1 LEVEL/MIC 2 LEVEL (98)
Turn to adjust the microphone volume.
ECHO LEVEL (99)
Turn to adjust the echo level.
/
PHONES jack
Connect the headphones.
0
Unit: MASTER VOLUME (38, 99, 105, 108)
Turn to adjust the volume.
Remote: VOLUME +/–2) (38, 99,
105)
Press to adjust the volume.
Remote: TV VOL +/–
Press to adjust the TV volume.
1)2)
(29)
Guide to parts and controls
Remote: TV CH +/–1) (29)
PresstochangetheTVchannels.
Continued
M
15
GB
11
HCD-GZR7D/GZR8D/GZR9D
1
Unit: DVD (26, 27, 34, 38, 76, 79,
98)
Press to select the “DVD” function.
Unit: USB (76, 81, 85, 98)
Presstoselectthe“USB”function.
Unit: TAPE A/B (74, 75)
Press to select the “TAPE” function. Presstoselect“TAPEA”or“TAPEB.”
Unit: TUNER/BAND (71, 72)
Press to select the “TUNER” function. Press to switch among FM and AM band.
Unit: DMPORT (116)
Press to select the “DMPORT” function.
Unit: VIDEO/SAT (116)
Press to select the “VIDEO” or “SAT” function.
Remote: FUNCTION +/– (27, 34, 38, 71, 74, 79, 83, 85, 98, 116)
Presstoselectthefunction.
2
(USB) port (78, 83, 85)
Connect an optional USB device.
(USB) indicator
Lights up in red when transferring or recording to the connected optional USB device or when erasing audio tracks or folders.
3
(MHC-GZR9D only)
SUBWOOFER (30)
SUBWOOFER indicator (30)
Lights up when the subwoofer is turned on.
4
PICTURE NAVI (54, 89)
Press to display the thumbnail pictures.
5
REPEAT/FM MODE (48, 73, 93)
Press to listen to a disc, an USB device, a
Press to select FM reception mode (monaural or stereo).
6
AUDIO (41, 99, 112)
Press to display the current audio signal ontheTVscreen.
7
SUBTITLE (40)
Pressto switchthelanguageofthe subtitle (DVD VIDEO only).
D. TUNING (72)
Press to switch to the direct tuning mode.
16
GB
12
HCD-GZR7D/GZR8D/GZR9D
8
ANGLE (40)
Press to change the angle (DVD VIDEO with multi-angles only).
9
DVD/TUNER MENU (49, 52, 58, 71, 87)
Press to display the menu items on the TV screen. Press to preset the radio station.
:
DISPLAY (28, 35, 44, 49, 55, 59,
60, 63, 80, 87, 102, 112, 139)
Press to display the Control Menu on the TV screen.
when the “DVD” function or “USB” function is selected.
;
TV1) (29)
Press to operate the TV functions.
XK
D STEP $ (39)
Presstoplayoneframeat a timewhen playback is paused.
ADVANCE (39, 53, 58, 87)
Press to advance the current scene during playback.
REPLAY (39, 53, 58, 87)
Press to replay the previous scene during playback.
XL
0 RETURN (43, 53, 59, 81, 88)
Presstoreturntothepreviousmenuon the TV screen.
XM
7/W/#/C (28, 29, 44, 45, 49, 71, 80, 96, 105)
Press to select the menu items.
F
DVD TOP MENU (49)
Press to display the DVD title on the TV screen.
FB
CLEAR (34, 36, 45, 51, 54, 70, 81,
89)
Press to delete a pre-programmed track
Press to erase audio tracks or folders from the connected optional USB device.
-/--1)(29)
Press to enter a single digit or double digit number.
FT
Numeric buttons2) (29, 39, 49, 60, 65, 72)
Press to select a track, chapter or video
Press to enter a password.
1)
10/0
Press to enter a double digit number.
Guide to parts and controls
Continued
M
17
GB
13
HCD-GZR7D/GZR8D/GZR9D
FE
KEY CONTROL / (101)
Presstochangethekeytosuityourvocal range.
SCORE (103)
Press to start or stop calculating your vocal score.
KARAOKE MODE (99)
Press to select the Karaoke mode.
KARAOKE PON (101)
Press to activate the “Karaoke Pon” function.
FG
TIME/TEXT (108, 110)
Press to change the information appearing in the front panel display or on-screen display.
FH
SLEEP (36, 105)
Press to set the Sleep Timer.
TV INPUT1) (29)
Press to switch the input sources.
FI
TIMER MENU (33, 105)
Presstosettheclockandthetimers.
FK
THEATRE SYNC (36)
Press to activate the “THEATRE SYNC” function.
1)
details, see “Operating a Sony TV” (page 29).
2)
VOLUME + remote have a tactile dot. Use the tactile dot as a reference when operating the system.
FE
RH
, TV VOL + RH,
and )RTbuttons on the
18
GB
14
Display
HCD-GZR7D/GZR8D/GZR9D
Guide to parts and controls
" Lights up when the output video
signal is NTSC. (27)
# Indicates the current surround
format.
$ Lights up when disc number is
displayed.
% Lights up when the ID3 tag
information is displayed.
& Lights up when the title or chapter
number is displayed.
' Lights up when the track information
is displayed.
( Lights up when playing VIDEO CD
with PBC function. (42)
) Lights up in “TUNER” function. (71) * Lights up when the USB device is
recognized. (85)
+ Lights up when the Karaoke Mode is
turned on. (98)
, Lights up during transfer or
recording. (75, 78, 83)
- Indicates the tape playback direction.
(74)
. Displays the text information. / Indicates the selected play mode. (44) 0 Indicates the disc presence. (38) 1 Lights up when “GROOVE” or “Z-
GROOVE” is turned on. (94)
2 3 Indicates the playback status of the
disc or USB device.
4 Lights up when the timer is set. (105) 5 Lights up when the “USB” function is
selected. (85)
6 Indicates the type of disc being played
back. (38)
7 Lights up when “PROGRESSIVE
(COMPONENT OUT)” is set to “ON.” (28)
19
GB
15
HCD-GZR7D/GZR8D/GZR9D
Hooking up optional components
To enhance your system, you can connect optional components. Refer to the operating instructions provided with each component.
Rear panel
MHC-GZR9D
MHC-GZR8D
MHC-GZR7D
Other Operations
Continued
M
113
GB
16
HCD-GZR7D/GZR8D/GZR9D
"
VIDEO/SAT AUDIO IN L/R jacks
Connect the audio output jacks of an optional component (such as VCR or satellite tuner).
#
VIDEO/SAT VIDEO IN jack
Connectthevideooutputjackofan optional component (such as VCR or satellite tuner).
$
COMPONENT VIDEO OUT jacks
Connect the component video input jacks of the TV or projector. If your TV accept progressive format signals, you must use this connection and set “PROGRESSIVE (COMPONENT OUT)” to “ON” (page 28). You can enjoy higher quality video images.
Note
You cannot output the video signal from the VIDEO/SAT VIDEO IN jack through the COMPONENT VIDEO OUT jacks of this unit.
%
VIDEO OUT jack
Connect the video input jack of the TV or projector.
&
S VIDEO OUT jack
Connect the S Video input jack of the TV or projector. You can enjoy higher quality video images when you select the S VIDEO.
Note
You cannot output the video signal from the VIDEO/SAT VIDEO IN jack through the S VIDEO OUT jack of this unit.
'
DMPORT (DIGITAL MEDIA PORT)
Connect the DIGITAL MEDIA PORT adapter (not supplied). You need to connect the DIGITAL MEDIA PORT adapter to an optional audio device (portable audio player, etc.).
Notes
Available DIGITAL MEDIA PORT
adapters vary in each area. Do not connect an adapter other than the
DIGITAL MEDIA PORT adapter. Do not connect or disconnect the
DIGITAL MEDIA PORT adapter to/from the DMPORT while the system is on.
When using a DIGITAL MEDIA PORT adapter (not supplied) that has video output function, connect the adapter directlytotheTV.
114
GB
17
HCD-GZR7D/GZR8D/GZR9D
(
D-LIGHT SYNC OUT jack (Except for Russian and Australian models)
Connect the D-LIGHT SYNC controller (not supplied). You need to connect the D-LIGHT SYNC controller to the lighting device* (not
react according to control signals transmitted by the D-LIGHT SYNC controller upon receiving music source from the system. For details on the use of D-LIGHT SYNC controller and lighting device, refer to the respective operating instructions supplied with the respective device.
* Refer to the D-LIGHT SYNC
controller operating instruction for the recommended lighting device.
Note
depending on the connected lighting device or the type of music being played back.
)
SUBWOOFER OUT jack (MHC­GZR8D/GZR7D only)
Connect the audio input jack of an optional subwoofer*.
* SA-GNV111D is recommended. In some
areas, the SA-GNV111D may not yet be available.
Note
occur depending on the connected subwoofer or the type of music being played back.
*
DVD DIGITAL OUT jack (MHC­GZR7D only)
Connect the digital optical input jack of an optional digital component
5.1 channel sound, if the connected
or DTS decoder.
Notes
Sound is output only when the system functionissetto“DVD”or“USB.”
If you press AUDIO
(
orthebuttonsrelatedtoKaraoke Mode, or if you connect or disconnect microphones or headphones, the sound
6
, SOUND FIELD
Other Operations
Continued
M
115
GB
18

DISASSEMBLY

• This set can be disassembled in the order shown below.
SET
HCD-GZR7D/GZR8D/GZR9D
SECTION 3
3-1. CASE (Page 20)
3-2. LOADING PANEL (Page 20)
3-3. TUNER PACK, DMPORT BOARD (Page 21)
3-4. DVD BLOCK SECTION (Page 21)
3-5. FRONT PANEL SECTION (Page 22)
3-13. TAPE MECHANISM DECK (Page 26)
3-19. VIDEO BOARD (Page 29)
3-20. DMB18 BOARD (Page 29)
3-23. DRIVER BOARD, SW BOARD (Page 31)
3-21. DVD ASSY (Page 30)
3-22. OPTICAL PICK-UP (Page 30)
3-24. SENSOR BOARD (Page 31)
3-25. MOTOR (TB) BOARD (Page 32)
3-26. MOTOR (LD) BOARD (Page 32)
3-14. MIC BOARD, HEADPHONE BOARD (Page 26)
3-15. LID (TC-L), LID (TC-R) (Page 27)
3-16. PANEL BOARD, VOLUME BOARD, KEY-RIGHT BOARD (Page 27)
3-17. USB BOARD (Page 28)
3-18. KEY-LEFT BOARD (Page 28)
3-6. SUB-TRANS BOARD (Page 22)
3-7. BACK PANEL SECTION (Page 23)
3-8. BOARDS SECTION (Page 23)
3-9. SURR & CENT AMP BOARD (HCD-GZR8D/GZR9D) (Page 24)
3-10. MAIN BOARD (Page 24)
3-11. REGULATOR BOARD (Page 25)
3-12. AMP FR & SW BOARD (Page 25)
19
HCD-GZR7D/GZR8D/GZR9D
Note: Follow the disassembly procedure in the numerical order given.

3-1. CASE

screw (case 3 TP2)
screw (case 3 TP2)
case
screw
(case 3 TP2)
screw
(case 3 TP2)
seven screws (+BVTP 3 × 8)

3-2. LOADING PANEL

CD mechanism deck (CDM74)
Turn the pulley to the direction of the arrow.
pulley
Front panel side
Pull-out the disc tray.
loading panel
20

3-3. TUNER PACK, DMPORT BOARD

HCD-GZR7D/GZR8D/GZR9D
DMPORT board
wire (flat type)(9 core)
(CN201)
CN203 (2P)
two screws
(+BVTP 3 × 8)
tuner pack
two screws
(+BVTP 3 × 6)
connector (9 core)

3-4. DVD BLOCK SECTION

RK DVD block section
RG wire (flat type)(9 core)
(CN502)
RE CN903 (3P)
screw
(+BVTP 3 × 8)
wire (flat type)(13 core) (CN701)
RH
wire
screw
(+BVTP 3 × 8)
RI
RT CN401 (5P)
RB CN111 (3P)
screw
(+BVTP 3 × 8) wire (flat type)(15 core) (CN503)
wire (flat type)(21 core)(CN201) (HCD-GZR8D/GZR9D) wire (flat type)(23 core)(CN202) (HCD-GZR7D)
two screws (+BVTP 3 × 8)
three screws (+BVTP 3 × 8)
four screws (+BVTP 3 × 8)
21
HCD-GZR7D/GZR8D/GZR9D

3-5. FRONT PANEL SECTION

front panel section
wire (flat type)(11 core)
(CN103)
CN073 (2P)

3-6. SUB-TRANS BOARD

CN901 (2P)
CN301 (3P)
CN302 (8P)
wire (flat type)(29 core)
(CN402)
wire (flat type)(9 core) (CN101)
four screws (+BVTP 3 × 8)
SUB-TRANS board
CN911 (4P)
three screws
(+BVTP 3 × 8)
22

3-7. BACK PANEL SECTION

HCD-GZR7D/GZR8D/GZR9D
four screws (+BVTP 3 × 8)
CN448 (4P) (HCD-GZR9D)
CN447 (9P)
screw
(+BVTP 3 × 8)
five screws (+BVTP 3 × 8)
CN602 (3P)
CN544 (6P)
(HCD-GZR8D/GZR9D)
back panel section
CN601 (3P)

3-8. BOARDS SECTION

boards section
screw
(+BVTP 3 × 6)
spring (EMC)
two screws
(+BVTP 3 × 8)
two screws (+BV3 (3-CR))
two screws (+BV3 (3-CR))
wire (flat type)(11 core) (CN102)
CN443 (5P)
CN907 (11P)
23
HCD-GZR7D/GZR8D/GZR9D

3-9. SURR & CENT AMP BOARD (HCD-GZR8D/GZR9D)

screw (+BVTP 3 × 8)
duct (fan)
SURR & CENT AMP board
bracket (PWB AMP)
two screws
(+BVTP 3 × 8)
two screws (transistor)
CN444 (7P)
screw
(+BVTP 3 × 8)

3-10. MAIN BOARD

MAIN board
screw
(+BVTP 3 × 8)
AMP FR & SW board
REGULATOR board
24

3-11. REGULATOR BOARD

HCD-GZR7D/GZR8D/GZR9D
four screws (+BVTP 3 × 8)
REGULATOR board
AMP FR & SW board

3-12. AMP FR & SW BOARD

bracket (PWB AMP-B)
screw
(+BVTP 3 × 8)
bracket (PWB AMP)
screw
(+BVTP 3 × 8)
two screws (transister)
screw (+BVTP 3 × 8)
screw (+BVTP 3 × 8)
AMP FR & SW board
screw
(+BVTP 3 × 8)
AMP HLDR board
heat sink assy
25
HCD-GZR7D/GZR8D/GZR9D

3-13. TAPE MECHANISM DECK

front panel assy
wire
two screws (+BVTP 2.6 (3CR))
tape mechanism deck

3-14. MIC BOARD, HEADPHONE BOARD

three knobs (MIC)
two screws
(+BVTP 2.6 (3CR))
two screws (+BVTP 2.6 (3CR))
front panel assy
HEADPHONE board
26
holder (MIC PWB)
HP HLDR board
screw
(+BVTP 2.6 (3CR))
two screws (+BVTP 2.6 (3CR))
three screws (+BVTP 2.6 (3CR))
MIC board

3-15. LID (TC-L), LID (TC-R)

spring (TC-L)
HCD-GZR7D/GZR8D/GZR9D
damper
lid (TC-L)
damper
spring (TC-R)
lid (TC-R)

3-16. PANEL BOARD, VOLUME BOARD, KEY-RIGHT BOARD

knob (VOL)
holder (JOG)
nut
knob (JOG)
front panel assy
RG VOLUME board
RE three screws
(+BVTP 2.6 (3CR))
front panel assy
RB CN606 (3P)
two screws
(+BVTP 2.6 (3CR))
KEY-RIGHT board
PANEL board
seven screws
(+BVTP 2.6 (3CR))
RT CN608 (3P) (HCD-GZR7D/GZR8D) CN607 (5P) (HCD-GZR9D)
three screws
six screws
(+BVTP 2.6 (3CR))
(+BVTP 2.6 (3CR))
27
HCD-GZR7D/GZR8D/GZR9D

3-17. USB BOARD

plate (USB) ground
wire
screw
(+BVTP 2.6 (3CR))
three screws (+BVTP 2.6 (3CR))
USB board

3-18. KEY-LEFT BOARD

front panel assy
KEY-LEFT board
28
six screws (+BVTP 2.6 (3CR))
front panel assy

3-19. VIDEO BOARD

HCD-GZR7D/GZR8D/GZR9D
three screws (+BVTP 3 × 8)
VIDEO board
wire (flat type)(15 core)
(CN901)

3-20. DMB18 BOARD

DMB18 board
two screws
(+BVTP 3 × 8)
DVD mechanism block
CN201 (6P)
wire (flat type)(24 core)
(CN101)
two screws (+BVTP 3 × 8)
wire (flat type)(21 core)(CN304) (HCD-GZR8D/GZR9D) wire (flat type)(23 core)(CN302) (HCD-GZR7D)
screw (+BVTP 3 × 8)
screw (+BVTP 3 × 8)
FFC HLDR3 board
FFC HLDR2 board
DVD mechanism block
29
HCD-GZR7D/GZR8D/GZR9D

3-21. DVD ASSY

FFC HLDR3 board
cover (CDM) section
screw
(+BVTP 3 × 8)
CN201 (6P)
screw
(+BVTP 3 × 8)
screw (+BVTP 3 × 8)
screw (+BVTP 3 × 8)
screw (+BVTP 3 × 6)
spring (EMC)
wire (flat type)(24 core)
(CN101) RB floating screw
(+PTPWH M2.6)
RT DVD assy

3-22. OPTICAL PICK-UP

two insulator screws
optical pick-up
DVD mechanism section
two insulators
two insulator screws
two insulators
30
holder (310)
Loading...
+ 98 hidden pages