Sony HBD-DZ330, DZ710, DZ730 Service manual

HBD-DZ330/DZ710/DZ730

SERVICE MANUAL

Ver. 1.0 2010.03

• HBD-DZ330/DZ710/DZ730 are the amplifi er, DVD/CD and
tuner section in DAV-DZ330/DZ710/DZ730.

This system incorporates with Dolby* Digital and Dolby Pro Logic (II)
adaptive matrix surround decoder and the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby

Laboratories.
** Manufactured under license under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and

worldwide patents issued & pending. DTS and DTS Digital Surround

are registered trademarks and the DTS logos and Symbol are trademarks

of DTS, Inc. © 1996-2008 DTS, Inc. All Rights Reserved.

AEP Model

HBD-DZ330/DZ730

UK Model

HBD-DZ330

Russian Model

HBD-DZ710

Model Name Using Similar Mechanism

Mechanism Type CDM85MB-DVBU102
Optical Pick-up Name KHM-313CAA

HBD-DZ170/DZ171/
DZ175/DZ310/DZ510/
DZ610/DZ810

Amplifi er Section
(DAV-DZ330/DAV-DZ730)

POWER OUTPUT (rated):
Front L + Front R 108 W + 108 W (at 3 ohms,
1 kHz, 1% THD)
POWER OUTPUT (reference):
Front L/Front R/Center/
Surround L/Surround R:
167 watts (per channel at 3
ohms, 1 kHz)
Subwoofer: 165 watts (at 3
ohms, 80 Hz)
Inputs (Analog)
TV (AUDIO IN) Sensitivity: 450/250 mV
AUDIO IN Sensitivity: 250/125 mV
Inputs (Digital)
TV (Audio Return Channel/OPTICAL IN)
Input Stream: Dolby
Digital 5.1ch/DTS 5.1ch/
Linear PCM 2ch
(Sampling Frequency: less
than 48 kHz)

SPECIFICATIONS

Amplifi er Section
(DAV-DZ710)

POWER OUTPUT (rated):
Front L + Front R 108 W + 108 W (at 3 ohms,
1 kHz, 1% THD)
POWER OUTPUT (reference)
Front L/Front R/Center/
Surround L/Surround R:
167 watts (per channel at 3
ohms, 1 kHz)
Subwoofer: 165 watts (at 3
ohms, 80 Hz)
Inputs (Analog)
TV (AUDIO IN) Sensitivity: 450/250 mV
MIC1 Sensitivity: 1 mV
MIC2 Sensitivity: 1 mV
Inputs (Digital)
TV (Audio Return Channel/OPTICAL IN)
Input Stream: Dolby
Digital 5.1ch/DTS 5.1ch/
Linear PCM 2ch
(Sampling Frequency: less
than 48 kHz)

Super Audio CD/DVD System

Laser Diode Properties Emission Duration:
Continuous
Laser Output: Less than

44.6 μW
* This output is the value measurement at a distance

of 200 mm from the objective lens surface on the
Optical Pick-up Block with 7 mm aperture.

Signal format system PAL/NTSC

USB Section

(USB) port:

Maximum current: 500 mA

Tuner Section

System PLL quartz-locked digital
synthesizer
Tuning range
North American models: 87.5 MHz - 108.0 MHz
(100 kHz step)
Other models: 87.5 MHz - 108.0 MHz (50
kHz step)
Antenna (aerial) FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency 10.7 MHz

– Continued on next page –

9-889-805-01

2010C04-1

2010.03

©

DVD RECEIVER

Sony Corporation

Audio&Video Business Group
Published by Sony Techno Create Corporation

HBD-DZ330/DZ710/DZ730

Video Section
(DAV-DZ330/DAV-DZ730)

Outputs VIDEO: 1 Vp-p 75 ohms
R/G/B: 0.7 Vp-p 75 ohms
HDMI OUT: Type A (19
pin)

Video Section
(DAV-DZ710)

Outputs VIDEO: 1 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
PB/CB, PR/CR: 0.7 Vp-p
75 ohms
HDMI OUT: Type A (19
pin)

General

Power requirements 220 V - 240 V AC,
50/60 Hz
Power consumption
DAV-DZ330 On: 170 W
Standby: 0.25 W*
DAV-DZ710/DAV-DZ730 On: 175 W
Standby: 0.25 W*

* Valid when the system is in the following status:
– “DEMO” is set to “OFF.”
– [CONTROL FOR HDMI] is set to [OFF].
– “S-AIR STBY” is set to “STBY OFF.” (DAV-DZ710/
DAV-DZ730)

Dimensions (approx.) 430 mm × 66 mm × 385
mm (w/h/d) incl.
projecting parts
Mass (approx.) 4.4 kg

Supported fi le format
MP3 (MPEG 1 Audio Layer-3)

File Extension: mp3
Bitrate: 32 kbps - 320 kbps
Sampling frequencies: 32/44.1/48 kHz

WMA (USB device only)

File Extension: wma
Bitrate: 48 kbps - 192 kbps
Sampling frequencies: 44.1 kHz

AAC (USB device only)

File Extension: m4a
Bitrate: 48 kbps - 320 kbps
Sampling frequencies: 44.1 kHz

DivX (except for United Kingdom models)

File Extension: avi/divx
Video codec: DivX video
Bitrate: 10.08 Mbps (MAX)
Frame rate: 30 fps
Resolution: 720 × 576
Audio codec: MP3

MPEG4

File format: MP4 File Format
File Extension: mp4/m4v
Video codec: MPEG4 Simple Profi le
(AVC is not compatible.)
Bitrate: 4 Mbps
Frame rate: 30 fps
Resolution: 720 × 576
Audio codec: AAC-LC (HE-AAC is not
compatible.)
DRM: Not compatible

Design and specifi cations are subject to change without notice.

SAFETY-RELATED COMPONENT WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

2

SPECIAL COMPONENT NOTICE

The components identifi ed by mark 9 contain confi dential infor-
mation.
Strictly follow the instructions whenever the components are re­paired and/or replaced.

Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.

This appliance is classifi ed as
a CLASS 1 LASER product.
This marking is located on the
rear or bottom exterior.

CAUTION

Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.

NOTES ON CHIP COMPONENT REPLACEMENT

• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

FLEXIBLE CIRCUIT BOARD REPAIRING

• Keep the temperature of soldering iron around 270 °C during

repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

HBD-DZ330/DZ710/DZ730

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead­free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350 °C.
Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)

than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.

• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

3

HBD-DZ330/DZ710/DZ730

Self-diagnosis Function

(When letters/numbers appear in the
display)

When the self-dia g nosis function is activ ate d to
prevent the system from malfunctio ning, a 5­character service number (e.g., C 13 50) with a
combination of a letter and 4 digits appears on
the TV screen or front panel display. In this case ,
check the following table.

C:13:50

First 3
characters of
the service
number

C 13 The disc is dirty.

E XX
(XX is a
number)

Cause and/or corrective action

,Clean the disc with a soft cloth.
To prevent a malfunction, the

system has performed the self­diagnosis function.
,Contact your nearest Sony

dealer or local authorized Sony
service facility and give the 5­character service number.
Example: E 61 10

MODEL IDENTIFICATION
– Back Panel –

Model Part No.

DZ330
DZ730
DZ710

Parts No.

4-159-511-0[]
4-159-513-9[]
4-159-514-0[]

When the version number
appears on the TV screen

When you turn on the system, the version
number [VER.X.XX] (X is a number) may
appear on the TV scre en. A l th ough this is not a
malfunction and for Sony service use only,
normal system oper at i on w i l l no t be possible.
Turn off the system, and then turn on the system
again to operate.

VER.X.XX

4

TABLE OF CONTENTS

HBD-DZ330/DZ710/DZ730

1. SERVICING NOTES

............................................. 6

2. DISASSEMBLY

2-1. Case ................................................................................ 9

2-2. Loading Panel ................................................................. 10

2-3. Front Panel Section ......................................................... 10

2-4. FL Board, ENCODER Board, JACK Board,

USB Board ...................................................................... 11

2-5. KEY-SW Board, P-SW Board ........................................ 12

2-6. Back Panel Section ......................................................... 13

2-7. MAIN Board ................................................................... 14

2-8. IO Board ......................................................................... 15

2-9. POWER Board ................................................................ 15

2-10. DVD Mechanism Deck Section ...................................... 16

2-11. Tray ................................................................................. 16

2-12. Belt .................................................................................. 17

2-13. MS-203 Board ................................................................. 17

2-14. Base Unit ......................................................................... 18

2-15. Optical Pick-up ............................................................... 18

3. TEST MODE ............................................................ 19

4. ELECTRICAL ADJUSTMENTS ........................ 23

5. DIAGRAMS

5-1. Block Diagram –RF Section– ......................................... 25

5-2. Block Diagram –VIDEO Section– ................................. 26

5-3. Block Diagram –AUDIO Section– ................................. 27

5-4. Block Diagram –AMP Section– ..................................... 28

5-5. Block Diagram –POWER Section– ................................ 29

5-6. Printed Wiring Board –MAIN Section (1/2)– ................. 31

5-7. Printed Wiring Board –MAIN Section (2/2)– ................. 32

5-8. Schematic Diagram –MAIN Section (1/9)– ................... 33

5-9. Schematic Diagram –MAIN Section (2/9)– ................... 34

5-10. Schematic Diagram –MAIN Section (3/9)– ................... 35

5-11. Schematic Diagram –MAIN Section (4/9)– ................... 36

5-12. Schematic Diagram –MAIN Section (5/9)– ................... 37

5-13. Schematic Diagram –MAIN Section (6/9)– ................... 38

5-14. Schematic Diagram –MAIN Section (7/9)– ................... 39

5-15. Schematic Diagram –MAIN Section (8/9)– ................... 40

5-16. Schematic Diagram –MAIN Section (9/9)– ................... 41

5-17. Printed Wiring Board –IO Section– ................................ 42

5-18. Schematic Diagram –IO Section– ................................... 43

5-19. Printed Wiring Boards

–JACK, KEY-SW, P-SW Section– ................................. 44

5-20. Schematic Diagram –JACK Section– ............................. 45

5-21. Schematic Diagram –KEY-SW, P-SW Section– ............. 46

5-22. Printed Wiring Boards

–SPEAKER, USB, MS-203 Section– ............................. 47

5-23. Schematic Diagram –SPEAKER, USB Section– ........... 48

5-24. Printed Wiring Boards –FL, ENCODER Section– ......... 49

5-25. Schematic Diagram –FL Section– .................................. 50

5-26. Schematic Diagram –ENCODER Section– .................... 51

5-27. Printed Wiring Board –S-AIR CON Section– ................ 52

5-28. Schematic Diagram –S-AIR CON Section– ................... 53

5-29. Printed Wiring Board –POWER Section– ...................... 54

5-30. Schematic Diagram –POWER Section– ......................... 55

6. EXPLODED VIEWS

6-1. Overall Section ............................................................... 69

6-2. Front Panel Section ......................................................... 70

6-3. Front Boards Section ...................................................... 71

6-4. Back Panel Section ......................................................... 72

6-5. Chassis Section ............................................................... 73

6-6. DVD Mechanism Deck Section

(CDM85MB-DVBU102) ................................................ 74

7. ELECTRICAL PARTS LIST .............................. 75

5

HBD-DZ330/DZ710/DZ730

SECTION 1

SERVICING NOTES

NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electro­static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body .
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

LASER DIODE AND FOCUS SEARCH

1. Open the case and turn POWER on with no disc inserted.

2. Confi rm that the following operation is performed while ob-
serving the objecting lens from the clearance of DVD mecha­nism deck.

1) Confi rm that laser beam is spread.

2) Up and down motion of the objective lens. (2 times)

DISC TRAY LOCK

The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.

Setting Procedure :

1. Press the [

2. Press the [FUNCTION] button to set DVD/CD function.

3. Insert a disc.

4. Press the [x] button and the [Z] button simultaneously for fi ve
seconds.

5. The message “LOCKED” is displayed and the tray is locked.

Releasing Procedure :

1. Press the [x] button and the [Z] button simultaneously for fi ve
seconds again.

2. The message “UNLOCKED” is displayed and the tray is un­locked.

Note: When “LOCKED” is displayed, the tray lock is not released by

turning power on/off with the [

] button to turn the set on.

?/1

?/1

] button.

How to open the disc table when power switch turns off

Insert a tapering driver into the aperture of the unit bottom, and
slide it in the direction of the arrow.

Insert a screwdriver from between the front panel and
the chassis and slide the rod in the direction of the arrow.

tray

Precaution when installing a new OP unit/
Precaution before unsoldering the static electricity
prevention solder bridge

On cleaning discs, disc/lens cleaners

• Do not use cleaning discs or disc/lens cleaners (including wet
or spray types). These may cause the apparatus to malfunction.

IMPORTANT NOTICE

Caution: This system is capable of holding a still video image or on­screen display image on your television screen indefi nitely. If you leave
the still video image or on-screen display image displayed on your TV
for an extended period of time you risk permanent damage to your tele­vision screen.
Projection televisions are especially susceptible to this.

6

When installing a new OP unit, be sure to connect the fl exible
printed circuit board fi rst of all before removing the static electric-
ity prevention solder bridge by unsoldering.
Remove the static electricity prevention solder bridge by unsolder­ing after the fl exible printed circuit board has already been con-
nected.
(Do not remove nor unsolder the solder bridge as long as the OP
unit is kept standalone.)

HBD-DZ330/DZ710/DZ730

Discharge the charged electricity in capacitors to prevent electric shock as follows

When disassembling the machine, be sure to discharge the charged electricity in the following capacitors.
Use a resistor of 800 ohms, 2 Watts for discharging the following capacitors.

POWER board
C903: 390V
C932, C933, C934, CN904: 30V

Point of capacitor discharge for C932, C933, C934:
Connect to the red and black wire of CN904.

Arranging the USB wire

USB wire

Tie up with LP501.

800:/2W

Point of capacitor discharge for C903:
Connect to the foot of C903.

The USB wire should be located on the front side
from these capacitors.

Have the USB wire spread on the inside
of the claws of the chassis.

Thread the USB wire through the capacitors.

Dress the USB wire in this area
properly along the board.

USB wire

MAIN board

7

HBD-DZ330/DZ710/DZ730

DISASSEMBLY

• This set can be disassembled in the order shown below.

SET

2-1. CASE
(Page 9)

SECTION 2

2-2. LOADING PANEL
(Page 10)

2-9. POWER BOARD
(Page 15)

2-3. FRONT PANEL SECTION
(Page 10)

2-4. FL BOARD,
ENCODER BOARD,
JACK BOARD,
USB BOARD
(Page 11)

2-6. BACK PANEL SECTION
(Page 13)

2-7. MAIN BOARD
(Page 14)

2-10. DVD MECHANISM DECK SECTION
(Page 16)

2-11. TRAY
(Page 16)

2-8. IO BOARD
(Page 15)

2-5. KEY-SW BOARD,
P-SW BOARD
(Page 12)

2-12. BELT
(Page 17)

2-13. MS-203 BOARD
(Page 17)

2-14. BASE UNIT
(Page 18)

2-15. OPTICAL PICK-UP
(Page 18)

8

Note: Follow the disassembly procedure in the numerical order given.

2-1. CASE

4 screw
(+BV3 (3-CR))

5

HBD-DZ330/DZ710/DZ730

3 four screws
(+BV3 (3-CR))

2 two screws
(+BV3 (3-CR))

1 two screws
(+BV3 (3-CR))

8 case

7

6 Raise one side of the case.

9

HBD-DZ330/DZ710/DZ730

2-2. LOADING PANEL

3 loading panel

Insert a screwdriver from between the front panel
and the chassis and slide the rod in the direction
of the arrow.

2-3. FRONT PANEL SECTION

2 two ground plate (front)

8 claw

1

tray

2

1 two screws

(+BV3 (3-CR))

qa CN5202 (4P)

0

10

6 four claws

9 three claws

4 nut

3 knob vol (DSZ)

7 claw

qs front panel section

5 four screws

(+BV3 (3-CR))

2-4. FL BOARD, ENCODER BOARD, JACK BOARD, USB BOARD

8 CN4007 (4P) (DZ330/DZ730)
CN4011 (4P) (DZ710)

HBD-DZ330/DZ710/DZ730

qa CN2101 (5P)

2 screw

(+BV3 (3-CR))

4 CN5006 (2P) (DZ330/DZ730)
CN5003 (4P) (DZ710)

1 wire (flat type) (13 core) (CN5005)
(DZ330/DZ730)
wire (flat type) (15 core) (CN5002)
(DZ710)

Arranging the USB wire

5 FL board

3 screw

(+BV3 (3-CR))

9 two screws
(+BV3 (3-CR))

7 ENCODER board

0 JACK board

6 claw

qs screw

(+BV3 (3-CR))

qd JACK board

USB wire

Tie up with LP501.

The USB wire should be located on the front side
from these capacitors.

Thread the USB wire through
the capacitors.

Dress the USB wire in this area
properly along the board.

USB wire

MAIN board

Have the USB wire spread on the inside
of the claws of the chassis.

11

HBD-DZ330/DZ710/DZ730

2-5. KEY-SW BOARD, P-SW BOARD

1 CN5301 (2P)

3 eight claws

escutcheon (DSZ)

2 five screws
(+BTP 2 u6)

4

8 KEY-SW board

6 P-SW board

12

7 two claws

5 two claws

2-6. BACK PANEL SECTION

DZ330

4 wire (flat type) (11 core)
(CN4009)

0 back panel section (DZ330)

HBD-DZ330/DZ710/DZ730

6 two screws
(+BVTP 3 u8)

5 screw
(+BVTP 3 u8)

7 screw
(+BVTP 3 u8)

8 screw
(+B 3 u6)

9 two screws
(+BVTP 3 u8)

3 CN3000 (2P)

2 CN5401 (4P)

1 CN901 (2P)

DZ710

5 wire (flat type) (11 core)
(CN4009)

6 CN102 (2P)

DZ730

5 wire (flat type) (11 core)
(CN4009)

6 CN102 (2P)

qs back panel section (DZ710)

qd back panel section (DZ730)

8 two screws

(+BVTP 3 u8)

7 screw
(+BVTP 3 u8)

9 screw
(+BVTP 3 u8)

0 screw
(+B 3 u6)

qa two screws
(+BVTP 3 u8)

3 CN3000 (2P)

2 CN5401 (4P)

4 wire (flat type) (12 core)

(CN306)

1 CN901 (2P)

9 two screws

(+BVTP 3 u8)

8 two screws
(+BVTP 3 u8)

7 screw
(+BVTP 3 u8)

0 screw
(+BVTP 3 u8)

qa screw
(+B 3 u6)

1 CN901 (2P)

qs two screws

(+BVTP 3 u8)

3 CN3000 (2P)

2 CN5401 (4P)

4 wire (flat type) (12 core)

(CN306)

13

HBD-DZ330/DZ710/DZ730

2-7. MAIN BOARD

6 wire (flat type) (11 core) (CN471)
(DZ330/DZ730)
wire (flat type) (9 core) (CN472)
(DZ710)

5 wire (flat type) (24 core) (CN1101)

7 wire (flat type) (19 core) (CN504)

(DZ330/DZ730)
wire (flat type) (21 core) (CN505)
(DZ710)

8 CN1501 (6P)

9 wire (flat type) (5 core)

(CN1502)

qh two screws
(+BV3 (3-CR))

qd four screws
(+BV3 (3-CR))

qf heat sink

4 CN2101 (5P)

qg five screws

(+BV3 (3-CR))

1 wire (flat type) (13 core) (CN507)
(DZ330/DZ730)
wire (flat type) (15 core) (CN506)
(DZ710)

Arranging the USB wire

USB wire

qj MAIN board

3 CN904 (5P)

2 CN906 (11P)

The USB wire should be located on the front side
from these capacitors.

0 two screws
(+BV3 (3-CR))

qs shield plate (PC-DSZ)

When the heat sink
has been removed,
apply oil compound
(G-747) to it.

qa insulated plate
(PC-DSZ)

14

Tie up with LP501.

Thread the USB wire through
the capacitors.

Dress the USB wire in this area
properly along the board.

USB wire

MAIN board

2-8. IO BOARD

4 two screws
(+BV3 (3-CR))

5 IO board

HBD-DZ330/DZ710/DZ730

1 CN4007 (4P) (DZ330/DZ730)
CN4011 (4P) (DZ710)

2 wire (flat type) (11 core) (CN4001)
(DZ330/DZ730)
wire (flat type) (9 core) (CN4002)
(DZ710)

3 wire (flat type) (19 core) (CN4005)
(DZ330/DZ730)
wire (flat type) (21 core) (CN4006)
(DZ710)

2-9. POWER BOARD

5 four screws
(+BV3 (3-CR))

8 POWER board

1 CN102 (2P) (DZ710/DZ730)

4 CN906 (11P)

3 CN904 (5P)

2 CN901 (2P)

6 four screws

(+BV3 (3-CR))

7 holder PC board

15

HBD-DZ330/DZ710/DZ730

2-10. DVD MECHANISM DECK SECTION

5 two screws
(+BV3 (3-CR))

8 two screws
(+BV3 (3-CR))

0 DVD mechanism deck

2 wire (flat type) (5 core)

(CN1502)

1 wire (flat type) (13 core) (CN507)
(DZ330/DZ730)
wire (flat type) (15 core) (CN506)
(DZ710)

6 screw
(+BV3 (3-CR))

7 cover (CDM-DSZ)

9 screw

(+BV3 (3-CR))

3 CN1501 (6P)

4 wire (flat type) (24 core)

(CN1101)

2-11. TRAY

1 Move the chuck cam
in the direction of the arrow.

bottom side

3 two claws

2

4

5 tray

16

2-12. BELT

2

chuck cam

3

HBD-DZ330/DZ710/DZ730

belt

2-13. MS-203 BOARD

3

MS-203 board

4

DC motor

1 two claws

2 three claws

1 screw

(M 1.7 u 2.5)

17

HBD-DZ330/DZ710/DZ730

2-14. BASE UNIT

2

chuck cam

3 two claws

1 two claws

4 base unit

2-15. OPTICAL PICK-UP

4 two insulator screws

2 FFC holder

3 two insulator screws

1 two claws

6 two insulators

5 two insulators

7 optical pick-up

(KHM-313CAA)

18

SECTION 3

TEST MODE

HBD-DZ330/DZ710/DZ730

Note: Incorrect operations may be performed if the test mode is not

entered properly.

In this case, press the [?/1] button to turn the power off, and

retry to enter the test mode.

1. Cold Reset

• The cold reset clears all data including preset data stored
in the RAM to initial conditions. Execute this mode when
returning the set to the customers.

Procedure:

1. Press the [

2. Press three buttons [

] button to turn the power on.

?/1

], [FUNCTION] and [

N

] simultane-

?/1

ously.

3. When this button is operated, display as “COLD RESET” for
a while and all of the settings are reset.

2. Panel Test Mode

• This mode is used to check the software version, FL and

KEY.

2-1. Display Test Mode
Procedure:

1. Press the [

] button to turn the power on.

?/1

2. While pressing the [x] and the [N] buttons simultaneously,
turn the [VOLUME] control in the direction of (+).

3. When the display test mode is activated, all segments are
turned on. When the mode in, “REC TO USB” is turn off.

4. To exit from this mode, while pressing the [x] and the [N]
buttons simultaneously, turn the [VOLUME] control in the di­rection of (+).

2-2. Version Test Mode
Procedure:

1. When the display test mode is activated, press the [FUNC­TION] button and the message “DSZ2E” (DZ330), “DSZ6KD”
(DZ710), “DSZ5E” (DZ730) are displayed, the version test
mode is activated.

2. Whenever the [FUNCTION] button is pressed, the display
changes in the following order.

“DSZ2E” (Model name) t “NA*1” (Destination) t MC V ersion

*1: NA changes depending on destination.

3. Press the [REC TO USB] button when the MC version is on
display. The date of software production is displayed.

4. Press the [REC TO USB] button again and the version is dis­played.

5. To exit from this mode, while pressing the [x] and the [N]
buttons simultaneously, turn the [VOLUME] control in the di­rection of (+).

2-3. FL Pattern Test Mode
Procedure:

1. When the display test mode is activated, press the [Z] button,
to select the FL pattern test mode. When the FL pattern test
mode, half segments of FL display and “REC TO USB” are
turn on.

2. Press the [Z] button, half segments of FL display and “REC
TO USB” are turn off.

3. Next press the [

] button, all segments of FL display is turn

Z

on.

4. To exit from this mode, while pressing the [

] and the [N]

x

buttons simultaneously, turn the [VOLUME] control in the di­rection of (+).

2-4. Key Test Mode
Procedure:

1. When the display test mode is activated, press the [

?/1

] but-

ton, to select the key test mode.

2. To enter the KEY test mode, the fl uorescent indicator displays
“K0 V0”. Each time an another button is pressed, “KEY” value
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, “K6
V0” is displayed.

3. When the [VOLUME] control is turned in the direction of (+),
“V0” is changed to “V1”, then ... “V9”.

When the [VOLUME] control is turned in the direction of (–),

“V0” is changed to “V9”, then ... “V1”.

4. To exit from this mode, while pressing the [

] and the [N]

x

buttons simultaneously, turn the [VOLUME] control in the di­rection of (+).

3. Disc Tray Lock

• The disc tray lock function for the antitheft of an demonstra-

tion disc in the store is equipped.

Setting Procedure :

1. Press the [

] button to turn the set on.

?/1

2. Press the [FUNCTION] button to set DVD function.

3. Insert a disc.

4. Press the [x] button and the [Z] button simultaneously for fi ve
seconds.

5. The message “LOCKED” is displayed and the tray is locked.

Releasing Procedure :

1. Press the [x] button and the [Z] button simultaneously for fi ve
seconds again.

2. The message “UNLOCKED” is displayed and the tray is un­locked.

Note: When “LOCKED” is displayed, the tray lock is not released by

turning power on/off with the [?/1] button.

4. DVD Version Display

• The STR and DVD microprocessor versions are displayed.

Procedure:

1. Press the [

2. Press the [N] button and the [

] button to turn the set on.

?/1

] button simultaneously for

?/1

three seconds. SC version display is presented.

3. Pressing the [FUNCTION] button presents a DV version dis­play. Pressing the [FUNCTION] button again returns to the SC
version display.

4. To exit from this mode, press any button other than the [FUNC­TION] button.

5. Product Out

• This mode moves the optical pick-up to the position durable

to vibration and clears all data including preset data stored
in the STR RAM to initial conditions. Use this mode when
returning the set to the customer after repair.

Procedure:

1. Press the [

] button to turn the power on.

?/1

2. Press the [FUNCTION] button to set the function “DVD/CD”.

3. Remove all discs.

4. While pressing the [x] and the [Z] buttons simultaneously,
turn the [VOLUME] control in the direction of (+).

5. Displayed to message “SERVICE IN” on the fl uorescent indi-
cator tube when pressing in turn the [4] t [DVD MENU] t
[CLEAR] buttons on the remote commander.

6. After the “STANDBY” blinking display fi nishes, the message
“MECHA LOCK” h “UNPLUG” is displayed on the fl uo-
rescent indicator tube disconnect the AC power plug, then the
product out mode is set.

The STR RAM initialization is executed upon a next power-on

after the power is turned off.

19

HBD-DZ330/DZ710/DZ730

6. D.C.A.C. (AUTOMATIC ACOUSTIC FIELD CALIBRA­TION) TEST MODE

Procedure:

1. Press the [

] button to turn the power on.

?/1

2. Press the [FUNCTION] button to set the function “ DVD/CD”.

3. Insert Calibration mic (ECM-AC2) supplied as an accessory
into the A.CAL MIC jack.

4. Press three buttons [x], [Z] and [REC TO USB] simultane­ously.

5. Confi rm that the following are shown on the display panel.

The JACK inserted/non-inserted detection display and the dis-

play.

* * * * * * * *

123

1 MIC detection condition

NON : Not detected
IN : Detected

2 Presence of DIGITAL sound data input to the microprocessor
NG: Input absent
OK: Input present

3 AD value (255h) of MIC input to the microprocessor

6. T o exit from this mode, press three buttons [x], [Z] and [REC
TO USB] simultaneously.

7. PROTECTION FACTOR (SD DETECTION/
DC DETECTION/TSD DETECTION) IDENTIFICATION
TEST MODE

When an error is detected, the FL tube alternately displays
“PROTECTOR h PUSH POWER”.
r Press the [
* Buttons other than the [

?/1

] button.

] button are invalid.

?/1

“STANDBY” blinks three times on the FL tube.
r
The protection release state (POWER OFF) is established.
(No FL tube display)
r Press the [

] button two times.

?/1

The power to the system turns on, and the normal operation is
established. (Restore)

During the protection state:

1. If the AC plug is connected or disconnected during the protec­tion state, the protection state is released, and the normal op­eration is established. (The protection state is not maintained.)

2. The protection factor is displayed by pressing the [RETURN]
t [3] t [2] t [0] t [0] t [ANGLE] buttons of the re­mote commander.

(during the “PROTECTOR” h “PUSH POWER” display).
k When SD is detected: Repeats
“SD DETECT” h “PROTECTOR”.
k When DC is detected: Repeats
“DC DETECT” h “PROTECTOR”.
k When TSD is detected: Repeats
“TMP DETECT” h “PROTECTOR”.

PL: SD detection

When the “L” output from the SD (shutdown) port on the

S-MASTER POWER Driver Shutdown and voltage descent
(15V or less) of 30V power supply (PVDD) are detected.

DC detection

When the “L” output from the power/speaker error detection

circuit (DC detection port) is detected for two seconds con­tinually, the power system other than that of the FL tube is
turned off, and the protection state is established.

TSD detection

When the “L” output from the thermal shutdown port

(TSDM) on the motor driver is detected.

20

HBD-DZ330/DZ710/DZ730

DVD SECTION

8-1. GENERAL DESCRIPTION

• The IOP measurement allows you to make diagnosis and ad­justment simply by using the remote commander and moni­tor TV. The instructions, diagnosis results, etc. are given on
the on-screen display (OSD).

Be sure to execute the IOP measurement when a BU (Base

Unit) is replaced.

8-2. HOW TO ENTER TEST MODE

While pressing the [
the [VOLUME] control in the direction of (+) with the DVD play­er in power on.
The Test Mode starts, displayed “SERVICE IN” on this model
display then the menu shown below will be displayed on the TV
screen.
* The display of the “Model Name” of the “Remocon Diagnosis

Menu” change with the model and the destination. Refer to

below on the model name.
DZ330 : DSZ2E
DZ710 : DSZ6KD
DZ730 : DSZ5E

0. External Chip Check

1. Servo Parameter Check

2. Drive Manual Operation

3. Emergency History

4. Version Information

5. USB Test Mode Setting
Model Name

IF-con : Ver. XX.XX (XXXX)
Syscon : Ver. X.XXX

*1: Changes depending on destination

The menu above is the Remocon Diagnosis Menu screen which
consists of fi ve main functions. At the bottom of the menu screen,
the model name and IF-con version. To exit from the Test Mode,
press the [

] button on the remote commander.

?/1

8-3. EXECUTING IOP MEASUREMENT

In order to execute IOP measurement, the following standard pro­cedures must be followed.

(1) In power on, while pressing the [x] and the [Z] buttons simul-

taneously, turn the [VOLUME] control in the direction of (+).

0. External Chip Check

1. Servo Parameter Check

2. Drive Manual Operation

3. Emergency History

4. Version Information

5. USB Test Mode Setting
Model Name : DSZ2E_XX

IF-con : Ver. XX.XX (XXXX)
Syscon : Ver. X.XXX

*1: Changes depending on destination

] and the [Z] buttons simultaneously, turn

x

Remocon Diagnosis Menu

1

: DSZ2E_XX

Remocon Diagnosis Menu

*

1

*

(2) Select “2. Drive Manual Operation” by pressing the [2] button

on the remote commander. The screen will appear as shown.

Drive Manual Operation

1. Servo Control

2. Track/Layer Jump

3. Manual Adjustment

4. Tray Aging Mode

5. MIRR time adjust

0. Return to Top Menu

(3) Select “3. Manual Adjustment” by pressing the [3] button on

the remote commander. The screen will appear as shown.

Manual Adjust

1. Track Balance Adjust:

2. Track Gain Adjust:

3. Focus Balance Adjust:

4. Focus Gain Adjust:

5. Eq Boost Adjust:

6. Iop:

7. TRV. Level:

8. S curve(FE) Level:

9. RFL(PI) Level:

0. MIRR Time:
Oo Change Value

[RETURN] Return to previous menu

(4) Select “6. IOP” by pressing the [6] button on the remote com-

mander.

(5) Wait until a hexadecimal number appear.

Manual Adjust

1. Track Balance Adjust:

2. Track Gain Adjust:

3. Focus Balance Adjust:

4. Focus Gain Adjust:

5. Eq Boost Adjust:

6. Iop. 47:

7. TRV. Level:

8. S curve(FE) Level:

9. RFL(PI) Level:

0. MIRR Time:
Oo Change Value

[RETURN] Return to previous menu

(6) Convert each data from hexadecimal to decimal using conver-

sion table.

(7) Please fi nd the label on the rear of the BU (Base Unit).
The default IOP value is written in the label.

(8) Subtract between these two values.

(9) If the remainder is smaller than 93 (decimal), then it is OK.

However if the value is higher than 93, then the BU is defec­tive and need to be change.

(10) Press the [RETURN] button on the remote commander to re-

turn back to previous menu.

(11) Press the [0] button on the remote commander to return to T op

Menu.

21

HBD-DZ330/DZ710/DZ730

8-4. EMERGENCY HISTORY

To check the emergency history, please follow the following pro­cedure.

(1) From the Top Menu of Remocon Diagnosis Menu, select “3.

Emergency History Check” by pressing the [3] button on the
remote commander. The following screen appears on the on­screen display.

Emg. History Check

Laser Hours CD 999h 59min

01. 01 05 04 04
00 00 00 00 00 00 23 45

02. 02 02 01 01 00 A9 4B 00
00 00 00 00 00 00 23 45

[Next] Next Page [Prev] Prev Page

[O] Return to Top Menu

DVD 999h 59min

00 92 46 00

(2) Y ou can check the total time when the laser is turned on during

playback of DVD and CD from the above menu. The maxi­mum time, which can be displayed are 999h 59min.

(3) You can check the error code of latest 10 emergency history

from the above menu. To view the previous or next page of
emergency history, press [.] or [>] button on the remote
commander. The error code consists of the following three
blocks. The fi rst block indicates the error code. The second
block indicates the parameter and the third block indicates the
time of error code as shown below.

60: Focus on error
61: Seek fail error
62: Read Q data/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can’t buffering
81: Unknown media type

8-4-1. Clear the Laser Hour

Press [

DISPLA Y] button and then press [CLEAR] button on the

remote commander. The data for both CD and DVD data are reset.

Emg. History Check

Laser Hours CD 0h 0min

01. 01 05 04 04
00 00 00 00 00 00 23 45

02. 02 02 01 01 00 A9 4B 00
00 00 00 00 00 00 23 45

[Next] Next Page [Prev] Prev Page

[O] Return to Top Menu

DVD 0h 0min

00 92 46 00

8-4-2. Clear the Emergency History

Press [DVD TOP MENU] button and then press [CLEAR] button
on the remote commander. The error code for all emergency his­tory would be reset.

Emg. History Check

• Error Code

Emg. History Check

Laser Hours CD 999h 59min

*1 *2

01. 01 05 04 04
00 00 00 00 00 00 23 45

02. 02 02 01 01 00 A9 4B 00
00 00 00 00 00 00 23 45

[Next] Next Page [Prev] Prev Page

[O] Return to Top Menu

DVD 999h 59min

00 92 46 00

*3

*1 : Error Code
*2 : Parameter of error code
*3 : Time of error code

The meaning of error code is as below:
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 Changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33: TE sensor adjustment error
34: TE loop gain adjustment error
35: FE loop gain adjustment error
36: Bad jitter after adjustment
40: Focus NG
42: Focus layer jump NG
51: Spindle stop error
52: Open kick spindle error

Laser Hours CD 999h 59min

01. 00 00 00 00
00 00 00 00 00 00 00 00

02. 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00

[Next] Next Page [Prev] Prev Page

[O] Return to Top Menu

DVD 999h 59min

00 00 00 00

8-4-3. Clear the Initialize Setup Data

Press [DVD MENU] button and then press [CLEAR] button on the
remote commander.

Emg. History Check

Laser Hours CD 999h 59min

[Next] Next Page [Prev] Prev Page

[O] Return to Top Menu

DVD 999h 59min

initialize setup data...

8-4-4. Return to the Top Menu of Remocon Diagnosis

Menu

Press [0] button on the remote commander.

22

HBD-DZ330/DZ710/DZ730

SECTION 4

ELECTRICAL ADJUSTMENTS

8-5. CHECK VERSION INFORMATION

To check the version information, please follow the following pro­cedure.

(1) From the Top Menu of Remocon Diagnosis Menu, select “4.

Version Information” by pressing the [4] button on the remote
commander. The following screen appears on the on-screen
display.

Version information

Firm (Main) : Ver. xxxxx
Firm (Sub) : xxxxx
RISC : xxxxx
8032 : xxxxx
Audio DSP : xxxxx
Servo DSP : xxxxx
Phy,Adr, : F.F.F.F

[O] Return to Top Menu

To return to the Top Menu of Remocon Diagnosis Menu, press

[0] button on the remote commander.

DVD SECTION

When the optical pick-up assy is replaced, perform the “EXECUT ­ING IOP MEASUREMENT”.

EXECUTING IOP MEASUREMENT (See page 21)

TUNER SECTION

[FM Tune Level Check]

generator

SET

Procedure:

1. Turn the power on.

2. Input the following signal from Signal Generator to FM an­tenna input directly.

FM ANTENNA

OUT (75 :)

* Carrier Freq : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation : 75 kHz
Modulation : 1 kHz
ANT input : 35 dBu (EMF)

Note: Please use 75 ohm “coaxial cable” to connect SG and the set. You

cannot use video cable for checking.

Please use SG whose output impedance is 75 ohm.

3. Set to FM tuner function and tune A, B and C signals.

4. Confi rm “TUNED” is lit on the display for A, B and C signals.

The mark of “TUNED” means “The selected station signal is re­ceived in good condition.”

23

HBD-DZ330/DZ710/DZ730

SECTION 5

DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)

For Printed Wiring Boards.

Note:

• X : Parts extracted from the component side.

• a : Through hole.

• : Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)

Caution:

Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)

• Indication of transistor.

C
Q

B

E

CEB

• Abbreviation
RU : Russian model

These are omitted.

Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.

These are omitted.

For Schematic Diagrams.

Note:

• All capacitors are in μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.

• f : Internal component.

• C : Panel designation.

Note: The components identifi ed by mark 0 or dotted

line with mark 0 are critical for safety.

Replace only with part number specifi ed.

• A : B+ Line.

• B : B– Line.

• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.

• Voltages and waveforms are dc with respect to ground in
service mode.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal production

tolerances.
no mark : TUNER (FM)

< > : DVD PLAY
* : Impossible to measure

• Voltages are taken with VOM (Input impedance 10 MΩ).

• Circled numbers refer to waveforms.

• Signal path.

F : TUNER
J : DVD PLAY
L : VIDEO
r : COMPONENT VIDEO
N : MIC
d : AUDIO IN

• Abbreviation

RU : Russian model

• Circuit Boards Location

P-SW board

MS-203 board

FL board

IO board

KEY-SW board

JACK board

S-AIR CON board (DZ710/DZ730)

MAIN board

SPEAKER board

POWER board

USB board

ENCODER board

24

5-1. BLOCK DIAGRAM – RF Section –

RF

VOA/A

DETECTOR

OPTICAL PICK-UP

BLOCK

(KHM-313CAA)

VOB/B
VOC/C
VOD/D

VOE/E+G

VOF/F+H

A

B

C

D

A
B
C
D

VC

(2.0V)

10

6
7
8
9

17
18

11
12
13
14

28

DVDRFIP

DVDA
DVDB
DVDC
DVDD

TNI
TPI

MA
MB
MC
MD

V20

CD/DVD RF AMP,

FOCUS/TRACKING ERROR AMP,

DVD SYSTEM CONTROL, DSP

IC1101 (1/3)

V2REFO

RXD
TXD

MC_DATA (ADIN)

HBD-DZ330/DZ710/DZ730

CN1105

6

27
105
106

206

(2.8V)

A/D CONVERTER

DOUT

9

SCKI

6

LRCK

7

BCK

8

IC303

VINL

VINR

RFMON

5

V2REFO
RXD
TXD

(SERVICE JIG)

L-IN

R-IN

B

(Page 27)

AUDIO

SECTION

2
1

13

14

LASER
DIODE

(FOR CD)

LASER
DIODE

(FOR DVD)

(LO:DVD, HI:CD) MSW

2AXIS
DEVICE
FOCUS/

TRACKING

COIL

LD (780)

LD (650)

VR (650)
VR (780)

VCC

FCS+

FCS-

TRK+

TRK-

PD

(SPINDLE MOTOR)

REG02

REG01

(SLED MOTOR)

LD DRIVE

(FOR CD)

Q1102 (1/2)

LD DRIVE
(FOR DVD)
Q1102 (2/2)

PD VOLUME

CONTROL

Q1101

Q1103

MM

MM

SP+

SP-

SL­SL+

IOP

LD01

22

MDI1

19

MDI2

20

LD02

21

MSW

54

FOCUS/TRACKING DRIVER,

LOADING/SPINDLE/SLED MOTOR DRIVER

OPIN+

28

OPIN–

29

VO1+

6

FOCUS COIL

VO1–

7

VO2–

9

TRACKING COIL

VO2+

8

MUTE123

34

2

11

VO3–
VO3+

VO4+

VO4–

REG DRIVER

SLED MOTOR

SPINDLE MOTOR

39

10

12

13

IC1501

BUFFER

DRIVE

DRIVE

DRIVE

DRIVE

STBY

LOADING

CONTROL

OPOUT

FWD

REV

VCTL

TSDM

BUS BUFFER

IC471

ACLK

203

ALRCK

205

ABCK

204

ASDATA2

223

ASDATA1

225

ASDATA0

226

ASDATA3

222

(LIMITSW)

LIMITSW

53

30

VCI

26

IN1

24

IN2

23

IN3

22

IN4

21
19
20
18
36

27

34
35

14
15

IOPMON

VREFO

FOO

TRO

FMO
DMO
FWD

REV
TROPENPWM
REGRST

SPFG

MUTE
TSD_M

FMO
FOO

DMO
TRO

39

IOPMON
VREFO

29

FMO

37

FOO

41

DMO

36

TRO

40

FWD

94

REV

95
38

TROPENPWM
REGRST

157

OP_INP

35

MUTE

158

TSD_M

130

XSYSRST

IFCK

IFSDO

IFSDI

XIFCS

KRMOD

MIC

OCSW

IFBSY

CKSW

108

98

97

100

99
213
208
104

110

103

XSYSRST

IFSCK

IFSDO

IFSDI

XIFCS

KRMOD

MIC

2 18
4 16
5 15
6 14
7 13
8 12
9 11

SYSTEM CONTROL

IC503 (1/5)

MTK_RST

45

DVD_SCO

49

DVD_SOD

48

DVD_SID

47

DVD XIFCS

51

KARAOKE MODE

53

TV_SEL/MIC_DET_OUT

52

CDM_OPEN_SW

44

DVD_XIFBUSY

50

TV_SEL

XSYSRST

XSYSRST

I

C

D

OCSW1/REVOCSW

CKSW/FWDCKSW

LDM+

LDM-

DZ710

VIDEO

SECTION

(Page 26)

VIDEO

SECTION

(Page 26)

AUDIO

SECTION

(Page 27)

S001

(CHUCK/TRAY DETECT)

AMP_D3
AMP_D2

AMP_D1
AMP_D0

DZ330/DZ730

M

(LOADING MOTOR)

MCKO

LRCKO

BCKO

x SIGNAL PATH

M001

AMP

A

SECTION

(Page 28)

: TUNER
: DVD PLAY

HBD-DZ330/DZ710/DZ730

2525

HBD-DZ330/DZ710/DZ730

5-2. BLOCK DIAGRAM – VIDEO Section –

SYSTEM CONTROL

IC503 (2/5)

CEC_TX_RX

17

82V_SEL1
81V_SEL0

72HDMI_PCONT

209WIDE
210RGB_SEL/DSEL

187CVBS
185Y/G

183B/Cb/Pb
182R/Cr/Pr

CEC_TX_OUT

DZ710/DZ730

DZ330/DZ730

RF

SECTION

(Page 25)

INHIBIT SWITCH

I

Q4003

TV_SEL

+5V
(IO)

FUNCTION SWITCH

CONTROL (TV/WIDE/PART)

Q4002, 4004 (1/2)

13 MUTE2

3MUTE1

4 CVBSIN

10 CVIN
12 CBIN
14 CRIN

A12V

VIDEO DRIVER

IC4000

D4001

CN4000 (1/2)

19

CVBS OUT

11

G OUT
B OUT

7

15

R/C OUT

8

FUNCTION SW

BLACKING CONTROL

(CVBS RGB)

Q4000, 4001, 4004 (2/2)

23CVBSOUT

20CYOUT

18CbOUT

16CrOUT

VOUT

CYOUT

CBOUT

CROUT

16

J4001 (1/2)

J4000

BLANKING OUT

VIDEO OUT

Y

PB/CB

PR/CR

T

COMPONENT

VIDEO OUT

DZ330/DZ730

EURO AV

OUTPUT (TO TV)

DZ710

DVD SYSTEM CONTROL, DSP

IC1101 (2/3)

SCL

SDA

112 101 102

7

6

5

WE EEWP

SCL

SDA

EEPROM

IC1103

180TX2P
179TX2N
177TX1P
176TX1N
174TX0P
173TX0N
171TCKP
170TCKN

162HTPLG

12

I2C_SCL

FLASHROM

IC1601

UK MODEL

13

I2C_SDA

4

RESET

RF

SECTION

(Page 25)

4

DZ710/DZ730

C

1

2

XSYSRST

BUFFER

IC1705

12

79,80,82–86,89

HD0–HD7

HD0–HD7

29,31,33,35,
38,40,42,44

RESET

D+3.3V

DZ330

HD0–HD7

DQ0–DQ7

HA0–HA21

56–64,67–75,77,

A0–A21

A0

25–16,10–1,48

A0–A19,N.CDQ15/A-1

FLASH ROM

IC1102

87,91,92

A1–A21

+6V

XRD

XROMCS

76

XWR

11OE28CE2645

WE

+5V REG.

IC1707

XWR

XRD78XROMCS

66

161

DDC_CLK

RD0–RD15

117–113,119–129

2,4,5,7,8,10,11,13,42,

44,45,47,48,50,51,53

RD0–RD15

159

DDC_DA

LEVEL SHIFT

Q1701

RA0–RA11

139–141,143,144

149–155

22–26,29–35

RA0–RA11

SDRAM

IC1104

CEC_TX_OUT

DRCLK

BA1

BA0

146

138

137

38

20

BA121BA0

CLK

_RCS

133

136

16

19

/CS

LEVEL SHIFT

Q9730

_CAS

_RAS

_RWE

111

134

135

15

18

/WE

/CAS17/RAS

DQM0

132

39

LDQM

DQM1

147

37

UDQM

CKE

CLKE

CN1701

1

TMDS DATA2 +

3

TMDS DATA2 –

4

TMDS DATA1 +

6

TMDS DATA1 –

7

TMDS DATA0 +

9

TMDS DATA0 –

10

TMDS CLOCK +

12

TMDS CLOCK –

19

HPD

18

+5V POWER

13

CEC
RESERVED

14
15

SCL

16

SDA

BUFFER

IC701

1 2

1A 3Y

HDMI OUT

SPDIF-ARC

ARC

E

x SIGNAL PATH

AUDIO

SECTION

(Page 27)

: VIDEO
: COMPONENT VIDEO

HBD-DZ330/DZ710/DZ730

2626

5-3. BLOCK DIAGRAM – AUDIO Section –

HBD-DZ330/DZ710/DZ730

+9V

DZ710

DZ710
J5101

MIC1/

A.CAL MIC

J5102

MIC2

DZ330/

DZ730
J5101

A.CAL MIC

J5102

AUDIO IN

TV

OUTPUT (TO TV)

T

AUDIO

IN

EURO AV

J4001(2/2)

L

R

J4000(2/2)

MIC BIAS

DZ330/DZ730

DZ710

DZ710

R-CH

DZ330/DZ730

A (L) IN

6

A (R) IN

2

R-CH

R-CH

SWITCH

Q5101,5102

MIC AMP

IC5101

5 7 3 1

LINE AMP/MIC AMP

IC5102

3 1

ELECTRONIC VOLUME

IC4004

7

VOUT2

2 1

VOUT1

MIC AMP ALC

IC4006

ALC

14

VIN2

VIN1

DATA

CLK

D5006

8

4
5

4

5

DC_CONT

PULG_DET

A.CAL

MIC

FUNCTION
SELECTOR

IC4003

5 3

Y1 Y

2

Y2

4

Y3

10

A

1

Y0

L

5 3
2
4

1

Y1 Y
Y2
Y3

Y0

FUNCTION
SELECTOR

IC4002

9

B

10

A

9

B

Q4006

Q4005

R-CH

L-IN
R-IN

ASEL0

ASEL1

DZ730

ASEL2

DZ730

B

ASEL0
ASEL1

ASEL2

PULG_DET

RF

SECTION

(Page 25)

AMP

SECTION

(Page 28)

ASEL0

84

ASEL1

85

ASEL2

86

MIC/A.CAL_SW/MIC2_SW

65

F

S-AIR_ADC_SEL

SD2
SD1
BCK

S-AIR_DET

S-AIR_SDA

S-AIR_CLK

S-AIR_RST

GPIO2

R-CH

36

38
30
29
37
35

DZ730

Rch

Lch

SD2

SD1
BCK1
BCK2

LRCK1LRCK
LRCK2

GND (for DET)

ADC_SEL

I2C_SDA
I2C_SCL

RESN

GPIO2

CN103

2
4

26
16
15
24

(S-AIR TRANSMITTER)

14
23
25

12
19
18
11

7

DZ710/DZ730

CN103

'<96

TV DIGITAL IN

ANTENNA

75: FM

COAXIAL

OPTICAL

TU4001

FM

TUNER

PACK

OPTICAL

RECEIVER

IC502

L-CH
R-CH
TUNED
DI
DO
CK
CE
RDS_DATA
RDS_CLK

R-CH

VIDEO

SECTION

(Page 26)

SECTION

(Page 25)

7

POWER

SECTION

(Page 29)

A.CAL
DC_CONT

MIC_DATA
MIC_CLK

TUNED
DI
DO
CK
CE
RDS_DATA
RDS_CLK

VBUS
D­D+
GND

DZ710

DIR

SPDIF-ARC

E

X301

24.576MHz

RF

XSYSRST

D

4

21

22

52

48 25

IC304

DIN1 (I)

XOUT (O)

XIN (I)

DIN2 (I)

XMODE (I) XVOICE/DIR_CSFLAG

AUDIO- (O)

24

ERROR (O)

34

XSTATE (O) SCORE/DIR_XSTATE

17

DATA (O)

16

BCK (O)

14

LRCK (O)

15

CKOUT (O)

13

DO (O)

35

DI (I)

36

CE (I)

37

CL (I)

CSFLAG (O)

38

MDIR_AUDIO

MDIR_ERROR

MDIR_XSTATE

SPDATA
SPBCK

SPLRCK

SPMCK

MDIR_DO

MDIR_DI

MDIR_CE

MDIR_CL

MDIR_CSFLAG

Q4007

MIC_CLK

MIC_DATA

DIR/USB CONTROL

IC1101 (3/3)

DIR_AUDIO/NC

52

DIR_ERROR/NC

51

198

ADIN (SPDATA)

202 197

SPBCK

200

SPLRCK

201

SPMCK

199

LT/DIR_DO

231

RT/DIR_DI

230

DIR_CE

221

DIR_CL

227
214 196

VBUS_OC

USB_DM

USB_DP

VBUS_OE

45
44

VBUS_SW

DZ710

VBUS DETECT

Q2101

G

91
42
69

70

80
77
78
79
76
74
75

USB 5V

1
2
3
4

A.CAL MIC LEVEL
DC_CONT
MIC_DATA

MIC_CLK

TUNED
ST_DI
ST_DO
ST_CLK
ST_CE
RDS_DATA
RDS_CLK

CN5501

(USB)

SYSTEM CONTROL

IC503 (3/5)

x R-ch is omitted due to same as L-ch.

x SIGNAL PATH

: TUNER
: MIC

: AUDIO IN

HBD-DZ330/DZ710/DZ730

2727

HBD-DZ330/DZ710/DZ730

5-4. BLOCK DIAGRAM – AMP Section –

AMP_D1 AMP_D3
AMP_D2
AMP_D3

A

: TUNER

BCKO

LRCKO

MCKO
AMP_D0

RF

SECTION

(Page 25)

x SIGNAL PATH

BCK

LRCK

SD1
SD2

SYSTEM CONTROL

IC503 (4/5)

LINK_SW

F

SECTION

(Page 27)

68A.CAL_OUT_LEVEL

63

1DAMP_SCDT

2DAMP_SHIFT
59DAMP LAT1
60DAMP LAT2
61DAMP LAT3
57DAMP INIT
58DAMP_SOFT_MUTE
55OVERFLOW1
56OVERFLOW2

54DRIVE_RST(EN)

67SD/PVDD_DET

66DC_DET

DZ710/DZ730

AUDIO

SD_PVDD_DET

SCDT

SHIFT

LAT1
LAT2
LAT3

NS_INIT

SOFTMUTE

OVF1
OVF2

DC-DET

EN

D3071

D3072

DATA SELECT

IC307
2
1

6

AMP_D2

AMP_D1
AMP_D3

5

MCK0
BCK0
LRCK0

OVF2
SCDT
SHIFT
LAT3
NS_INIT

SOFTMUTE

AMP_D1

MCK0
BCK0
LRCK0

SCDT
SHIFT
LAT1
NS_INIT

SOFTMUTE

MCK0
BCK0
LRCK0
OVF1
SCDT
SHIFT
LAT2
NS_INIT

SOFTMUTE

D3.3V

S-MASTER PROCESSOR

IC3030

DATA

31
36 XFSIIN

30 BCK
29 LRCK
25 OVF FLAGL
24 OVF FLAGR
21 SCDT
22 SCSHIFT
23 SCLATCH
27 INIT

19 SOFTMUTE
18 NSPMUTE

S-MASTER PROCESSOR

IC3010

31

DATA

36 XFSIIN
30 BCK
29 LRCK
25 OVF FLAGL
24 OVF FLAGR
21 SCDT
22 SCSHIFT
23 SCLATCH
27 INIT

19 SOFTMUTE
18 NSPMUTE

S-MASTER PROCESSOR

IC3020

DATA

31
36 XFSIIN

30 BCK
29 LRCK
25 OVF FLAGL
21 SCDT
22 SCSHIFT
23 SCLATCH
27 INIT

19 SOFTMUTE
24 OVF FLAGR
18 NSPMUTE

PVDD DOWN PROTECT

Q3552

BUFFER

Q502

OUTR1(+)

OUTR1(+)

OUTR1(+)

FAN

CONTROL

Q3001

D3551

LPF

LPF

LPF

LPF

LPF

LPF

LPF

LPF

LPF

LPF

LPF

LPF

M+14V

DC BALANCE

DETECT

Q3301

DC BALANCE

DETECT

Q3401

DC BALANCE

DETECT

Q3101

DC BALANCE

DETECT

Q3151

DC BALANCE

DETECT

Q3201

DC BALANCE

DETECT

Q3202

Q3000

FAN

DRIVER

TB3901

TB5401

DC FAN

FAN3001

(+)

SUBWOOFER

(–)

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

CENTER

SPEAKERS

FRONT R

FRONT L

SUR R

SPEAKERS

SUR L

DIGITAL POWER AMP

IC3300

X3051

49.152MHz

CLOCK

GENERATOR

IC3051

H

SW+
SW–

C+
C–

FR+
FR–
FL+
FL–

SR+
SR–
SL+
SL–

PVDD (+32.5V)

POWER

SECTION

6
4OUTR2(–)

11OUTL1(+)

9OUTL2(–)

38FS0I
48XFS0IN

6
4OUTR2(–)

11OUTL1(+)

9OUTL2(–)

37FS0CKOUT
38FS0I

14XFS0OUT

48XFS0IN

6
4OUTR2(–)

11OUTL1(+)

9OUTL2(–)

38FS0I

14XFS0OUT

48XFS0IN

EN

16 PWM_C
18 PWM_D
17 /RESET_CD

5/SD

6 PWM_A
8 PWM_B
7 /RESET_AB

DIGITAL POWER AMP

IC3100

16 PWM_C
18 PWM_D
17 /RESET_CD

5/SD

6 PWM_A
8 PWM_B
7 /RESET_AB

DIGITAL POWER AMP

IC3200

16 PWM_C

8 PWM_D
7 /RESET

5/SD

8 PWM_A

16 PWM_B

7

/RESET

DC BALANCE

PROTECT

Q3551

OUT_C
BST_C
OUT_D
BST_D

OUT_A

BST_A

OUT_B

BST_B

OUT_C
BST_C
OUT_D
BST_D

OUT_A

BST_A

OUT_B

BST_B

OUT_C
BST_C
OUT_D
BST_D

OUT_A

BST_A

OUT_B

BST_B

31
33
28
24

39
43
36
34

31
33
28
24

39
43
36
34

31
33
28
24

39
43
36
34

(Page 29)

HBD-DZ330/DZ710/DZ730

2828