Sony FMP-X10 Reference Guide
©2014 Sony Corporation Printed in Japan 4-540-861-11(1)
Media Player
Reference Guide
Sony Customer Support
http://www.sony.com/4ksupport/
1-855-476-6945 (1-855-4Sony4K)
Please Call Before Returning the Product to
the Store
FMP-X10
Owner’s Record
The model and serial numbers are located at the
bottom of the unit. Record the serial number in the
space provided below. Refer to them whenever you
call upon your Sony dealer regarding this product.
Model No. FMP-X10
Serial No.______________
WARNING
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To avoid electric shock, do not open the cabinet. Refer
servicing to qualified personnel only.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
These graphical symbols are located on the AC
adapter.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Do not expose batteries or appliances with battery-
installed to excessive heat, such as sunshine and fire.
WARNING
DO NOT INGEST BATTERY, CHEMICAL
BURN HAZARD
The remote control supplied with this product
contains a coin/button cell battery. If the coin/button
cell battery is swallowed, it can cause severe internal
burns in just 2hours and can lead to death.
Keep new and used batteries away from children. If
the battery compartment does not close securely,
stop using the product and keep it away from
children.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
Precautions
The player is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the player itself has been turned off.
Install this unit so that the AC power cord can be
unplugged from the wall socket immediately in the
event of trouble.
The nameplate is located on the bottom of the
player.
Installing
Do not install this player in a confined space, such as
a bookshelf or similar unit.
FCC WARNING
You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
The shielded Interface cable (LAN cable) must be
used with the equipment in order to comply with the
limits for a digital device pursuant to Subpart B of Part
15 of FCC Rules.
NOTE
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software,
which is the passed down through the MAC, through
the digital and analog baseband, and finally to the RF
chip. Several special packets are initiated by the MAC.
These are the only ways the digital baseband portion
will turn on the RF transmitter, which it then turns off
at the end of the packet. Therefore, the transmitter
will be on only while one of the aforementioned
packets is being transmitted. In other words, this
device automatically discontinue transmission in case
of either absence of information to transmit or
operational failure.
Frequency Tolerance: 20ppm
5.15 – 5.25GHz band is restricted to indoor operations
only.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment and
meets the FCC radio frequency (RF) Exposure
Guidelines. This equipment should be installed and
operated keeping the radiator at least 20cm or more
away from person’s body (excluding extremities:
hands, wrists, feet and ankles).
For the State of California, U.S.A. only
Perchlorate Material: special handling may apply.
See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains
perchlorate.
Important Safety
Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement of
the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
Precautions
On placement
Place the player in a location with adequate
ventilation to prevent heat build-up in the
player.
Do not place the player on a soft surface such as
a rug that might block the ventilation holes.
Do not place the player in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust, or mechanical shock.
Do not place the player outdoors, in vehicles, on
ships, or on other vessels.
If the player is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may form on the outer surface and on
interior of the player.
Should this occur, the player may not operate
properly. In this case, leave the player turned on
for about half an hour until the moisture
evaporates.
Do not install the player in an inclined position. It
is designed to be operated in a horizontal
position only.
Do not place heavy or unstable objects on the
player.
Disconnect the AC power cord and all other
cables from the player when you move the
player.
Keep the player away from equipment with
strong magnets, such as microwave ovens, or
large loudspeakers.
Do not place metal objects in front or on the
both sides of the player. It may limit reception of
radio waves.
Do not place the player in a place where medical
equipment is in use. It may cause a malfunction
of medical instruments.
If you use a pacemaker or other medical device,
consult your physician or the manufacturer of
your medical device before using the wireless
LAN function.
About the hard disk drive
The hard disk has a high storage density, which
enables quick access to the written data. However,
it can easily be damaged by shock, vibration or
dust, and should be kept away from magnets. To
avoid losing important data, observe the following
precautions.
Do not apply a strong shock to the player.
Do not place the player in a location subject to
mechanical vibrations or in an unstable location.
Do not place the player on top of a hot surface,
such as a VCR or amplifier (receiver).
Do not use the player in a place subject to
extreme changes in temperature (temperature
gradient less than 10 °C/hour).
Do not move the player with its AC power cord
connected.
Do not disconnect the AC power cord while the
power is on.
Do not move the player for one minute after you
have unplugged the AC power cord.
Do not attempt to replace or upgrade the hard
disk by yourself, as this may result in
malfunction.
If the hard disk drive should malfunction, you
cannot recover lost data. The hard disk drive is
only a temporary storage space.
About repairing the hard disk drive
The contents of the hard disk drive may be
checked in case of repair or inspection during a
malfunction or modification. However, the
contents will not be backed up or saved by Sony.
If the hard disk needs to be formatted or
replaced, it will be done at the discretion of
Sony. All contents of the hard disk drive will be
erased, including contents that violate copyright
laws.
On power sources
Follow the procedure below when disconnecting
the AC power cord.
Disconnect the LAN cable or pause the
download by using the 4K application setting
in the “Application” items of the player home
menu.
Wait for about five minutes after turning the
player off.
Make sure that the hard disk drive is not
operating (the power indicator and HDD
indicator are off).
Disconnect the AC power cord.
Disconnect the player from the wall outlet if you
are not going to use the player for a long time.
To disconnect the AC power cord, grasp the plug
itself; never pull the cord.
Observe following points to prevent the AC
power cord being damaged. Do not use the AC
power cord if it is damaged, as doing so may
result in an electric shock or fire.
Do not pinch the AC power cord between the
player and wall, shelf, etc.
Do not put anything heavy on the AC power
cord or pull on the AC power cord itself.
Printed using VOC (Volatile Organic
Compound)-free vegetable oil based ink.
http://www.sony.net/
On AC adapter
Use the supplied AC adapter for this player, as
other adapters may cause a malfunction.
Do not disassemble or reverse-engineer.
Do not confine the AC adapter in a closed place
such as a bookshelf or an AV cabinet.
Do not connect the AC adapter to a traveler’s
electric transformer, which may generate heat
and cause a malfunction.
Do not drop or apply shock.
On adjusting volume
Do not turn up the volume while listening to a
section with very low level inputs or no audio
signals. If you do, your ears and the speakers may
be damaged when a peak level section is played.
On cleaning
Clean the cabinet, panel, and controls with a soft
cloth. Do not use any type of abrasive pad,
scouring powder or solvent such as alcohol or
benzine.
On replacement of parts
In the events that this player is repaired, repaired
parts may be collected for reuse or recycling
purposes.
On connecting to the HDMI jack
Observe the following as improper handling may
damage the HDMI jack and the connector.
Carefully align the HDMI jack on the rear of the
player and the HDMI connector by checking their
shapes. Make sure the connector is not upside
down or tilted.
HDMI jack
Replacing the battery of
the remote control
1
Pull out the battery compartment with a stick.
2 Replace the old battery with a new one.
Insert the new battery with the side facing
up.
CR2032 battery
manufactured by Sony
3 Close the battery compartment.
Specifications
Input/Output jacks
HDMI OUT 1 (for AUDIO VIDEO) HDMI 19-pin standard connector
HDMI OUT 2 (for AUDIO) HDMI 19-pin standard connector
LAN (100) 100 BASE-TX Terminal
EXTRA HDD Rear USB port: For connecting external hard disk drive*
USB Front USB port: For connecting USB memory*
Power and others
Power requirements Input: DC 19.5 V, 2.0 A
Power consumption 43 W
AC adapter Input: 100 V - 240 V AC, 50/60 Hz, 1.0 A
Operating temperature 5 °C to 35 °C (41 °F to 95 °F)
Operating humidity 25% to 80%
Dimensions (approx.) 250 mm × 250 mm × 50 mm (9 7/8 in. × 9 7/8 in. × 2 in.)
Mass (approx.) 2.5kg (5.6 lb.)
Hard disk drive capacity 1 TB
Wireless LAN
Wireless LAN standard IEEE 802.11a/b/g/n
Frequency band 2.4 GHz, 5 GHz
Modulation DS-SS Modem and OFDM Modem
Accessories
Supplied accessories AC power cord (1)/AC adapter (1)/High Speed HDMI cable (1) /Remote
* For details on USB devices that can be connected to the player, see “Help Guide”
(http://rd1.sony.net/help/hv/fmpx10/en/).
Specifications and design are subject to change without notice.
Video: 3840 × 2160
Frame rate: 24p, 25p, 30p, 50p, 60p
Audio: Linear PCM, Dolby Digital, Dolby Digital Plus
Linear PCM, Dolby Digital, Dolby Digital Plus
Output: DC 19.5 V, 4.35 A
(width/depth/height) excl. projecting parts
control RMT-D304 with CR2032 battery (1) /Startup Guide, Reference
Guide, End User License Agreement and Warranty card
HDMI jack
Be sure to disconnect the HDMI cable when
moving the player.
Hold the HDMI connector straight when
connecting or disconnecting the HDMI cable. Do
not twist or force the HDMI connector into the
HDMI jack.
IMPORTANT NOTICE
Caution: This player is capable of holding a
still video image or on-screen display image
on your television screen indefinitely. If you
leave the still video image or on-screen
display image displayed on your TV for an
extended period of time, you risk permanent
damage to your television screen. Plasma
display panel televisions and projection
televisions are susceptible to this.
If you have any questions or problems concerning
your player, please consult your nearest Sony
dealer.
Additional Information
About wireless LAN security
Since communication via the wireless LAN
function is established by radio waves, the
wireless signal may be susceptible to interception.
To protect wireless communication, this player
supports various security functions. Be sure to
correctly configure the security settings in
accordance with your network environment.
No Security
Although you can easily make settings, anyone
can intercept wireless communication or intrude
into your wireless network, even without any
sophisticated tools. Keep in mind that there is a
risk of unauthorized access or interception of data.
WEP
WEP applies security to communications to
prevent outsiders from intercepting
communications or intruding into your wireless
network. WEP is a legacy security technology that
enables older devices, which do not support TKIP/
AES, to be connected.
WPA-PSK (TKIP), WPA2-PSK (TKIP)
TKIP is a security technology developed to correct
for the deficiencies of WEP. TKIP assures a higher
security level than WEP.
WPA-PSK (AES), WPA2-PSK (AES)
AES is a security technology that uses an
advanced security method that is distinct from
WEP and TKIP. AES assures a higher security level
than WEP or TKIP.
Trademark Information
MPEG Layer-3 audio coding technology and
patents licensed from Fraunhofer IIS and
Thomson.
The terms HDMI™ and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
WPA™ and WPA2™ are marks of the Wi-Fi
Alliance.
This product incorporates proprietary technology
under license from Verance Corporation and is
protected by U.S. Patent 7,369,677 and other U.S.
and worldwide patents issued and pending as
well as copyright and trade secret protection for
certain aspects of such technology. Cinavia is a
trademark of Verance Corporation.
Copyright 2004-2014 Verance Corporation. All
rights reserved by Verance. Reverse engineering
or disassembly is prohibited.
TUXERA is a registered trademark of Tuxera Inc.
in the US and other countries.
Other system and product names are generally
trademarks or registered trademarks of the
manufacturers. ™ and ® marks are not indicated
in this document.
Cinavia Notice
This product uses Cinavia technology to limit the
use of unauthorized copies of some commerciallyproduced film and videos and their soundtracks.
When a prohibited use of an unauthorized copy is
detected, a message will be displayed and
playback will be interrupted.
More information about Cinavia technology is
provided at the Cinavia Online Consumer
Information Center at http://www.cinavia.com.
To request additional information about Cinavia
by mail, send a postcard with your mailing
address to: Cinavia Consumer Information Center,
P.O. Box 86851, San Diego, CA, 92138, USA.
About MPEG-4 AVC
THIS PRODUCT IS LICENSED UNDER THE AVC
PATENT PORTFOLIO LICENSE FOR THE PERSONAL
USE OF A CONSUMER OR OTHER USES IN WHICH IT
DOES NOT RECEIVE REMUNERATION TO (i)ENCODE
VIDEO IN COMPLIANCE WITH THE AVC STANDARD
(“AVC VIDEO”) AND/OR (ii)DECODE AVC VIDEO
THAT WAS ENCODED BY A CONSUMER ENGAGED
IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED
FROM A VIDEO PROVIDER LICENSED TO PROVIDE
AVC VIDEO.
NO LICENSE IS GRANTED OR SHALL BE IMPLIED
FOR ANY OTHER USE. ADDITIONAL INFORMATION
MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE
HTTP://WWW.MPEGLA.COM
Loading...