Sony EXECUTIVE MiniDome OSD User Manual

EXECUTIVE / MiniDome

OSD

USERS MANUAL

USING THE MOTOSAT DISH POINTING SYSTEM

EXECUTIVE / MiniDome OSD

MotoSAT Corporation

Created April 22, 2003

1-800-247-7486

CONGRATULATIONS!

…on your purchase of your Satellite RV-TV system from MotoSAT.

We are excited here at MotoSAT to introduce to you the cutting edge of Satellite technology. The features of the new dish positioning system will have you feeling in total control.

SYSTEM FEATURES

• Totally automated. Just select “Find Satellite” and the dish

will do the rest

• Control your satellite system with your receivers remote

control

• On-Screen menus allow for easy configuration of your system

• Move to any satellite at will with your remote control

• Locate ANY satellite and add it to your system

• Quick reacquiring of last acquired satellite

• Re-peaking option if vehicle has settled

• Auto Stow within one minute if the vehicle has been moved

• Manual stowing of Dish without having to turn on TV

• Works with DirecTV, Dish Network and Bell Express VU with

Infrared remote capability

TABLE OF CONTENTS

Do You Have The Right Receiver?………………………….…. 4 MotoSAT Shipped Components………………………………... 4 The MotoSAT Positioner………………………………………… 5 How to Reset Memory …………………………………… 5 Functions of your MotoSAT System………………………….. 6 Using your MotoSAT System…………………………………... 7 THE MAIN MENU SCREEN……………………………………… 8

Changing receiver output between channel 3 and 4

THE SETUP SCREEN………………………………………….... 11

THE INFORMATION SCREEN…………………………………. 12 THE DIAGNOSTIC SCREEN…………………………………… 13

High Operating Temperature warning

THE OPTIONS MENU SCEEN……………………………….... 13

THE SATELLITE SETUP SCREEN…………………………… 15 THE POWER BUTTON MENU SCREEN…………………….. 16 How to use the OSD with any receiver……………………… 16

Tone Setting

WIRING DIAGRAM……………………………………………… 17

Rear View

Dry-Camping (Power Saving)

WARRANTY ……………………………………………………… 20 TROUBLESHOOTING………………………………………….. 24 FIGURE 1 (Receiver set back).………………………………. 25 FIGURE 2 (O-Ring style F-Connectors) …………………… 26 FIGURE 3 (A/B Switches) …………………………………….. 27 UPDATING RECEIVER SOFTWARE ………………………… 28

DO YOU HAVE THE RIGHT RECEIVER?

Note: Receivers with remotes that do not output Infrared will not operate the OSD.

Your MotoSAT dish will work with most all new receivers, but some of the older receivers may not operate properly. Please make sure that your receiver type is listed below*:

DISH NETWORK - The Positioner will operate with most all Dish Network Satellite Receivers, past and current (some exceptions may apply, see above). Please consult MotoSAT Technical support with any questions or concerns.

DirecTV – Works with:

*RCA Models - 420 Series (420, 440 480) and 430 Series (430, 450, 485).

Sony SAT-A65, B65, A65-A, B65-A Hughes GCEBO, GCEBOA, GAEBO, GABEOA, Remotes on these models are EXTREMELY sensitive and are not recommended.

SYSTEM SHIPPED COMPONENTS

Your MotoSAT satellite system would have shipped with these components.

THE MotoSAT Executive OSD Positioner

NOTE – You will need to place the MotoSAT Positioner (OSD) inside the same cabinet that your receiver is located. Wireless communication is happening between the MotoSAT Positioner and the TV Receiver that is not possible when units are separated (see Figure 1).

LIGHTS & BUTTONS

GREEN LIGHT - The green light on the far-left side of the front panel shows that the Dish LNB is getting power from the Satellite TV Receiver.

RED LIGHT 1 – The first red light on the left, when blinking, shows that the Positioner is receiving a command from your Remote.

RED LIGHT 2 – The second red light, when blinking, shows that the dish is moving.

POWER - The MotoSAT Positioner only has one button for turning the system ON and OFF. When pressed, it will

turn ON the positioner and glow blue.

a. When pressed for longer than 10 seconds, this button will automatically stow a raised dish.

b. When pressed for longer than 30 seconds, this button will erase the Remote Setting and then the

display will ask you to press the Guide button on your remote to pick your receiver type. This task will also erase all satellite selections except 101° (DirecTV), 119° (Dish NetWork) and 91° (Bell ExpressVu)

This is a Memory Reset Function

FUNCTIONS OF YOUR MotoSAT SYSTEM

AUTOMATIC SEARCH AND LOCK ON THE CORRECT SATELLITE

MotoSAT gives you on-screen control of your satellite system. No matter where you find yourself in the United States, your system is smart enough to make sure you have connected to the satellite of your choice. Simply choose “Find Satellite” on the Main Menu screen displayed on your TV and follow the on-screen instructions.

STOWING THE DISH

Stowing the dish is only necessary when using the MotoSAT Executive “open face” dish, which does need to be stowed for traveling. You have the option of stowing the dish from the on-screen controls, or by pressing and holding the ON button of the Positioner for more than 10 seconds.

QUICK RE-ACQUIRING OF LAST KNOWN SATELLITE

Sometimes you may have wanted to stow the dish because of high winds of some other reason. As long as the vehicle has not moved, you may choose this option from the main menu and the dish will rise up and go directly to the satellite with out having to do a search pattern.

MOVING THE DISH TO ANOTHER SATELLITE

You have the option of moving your dish to another satellite at will when a different satellite has different programming. To change satellites while you’re watching TV, press the OFF button on the remote…this action will bring up the MotoSAT Power Off menu that allows you to switch to another satellite. Here you may highlight the satellite you wish to move to.

NOTE – All MotoSAT systems normally come with only one Satellite location. Adding other satellite locations is easy. All you need are the “working” satellite longitudes from your dealer and enter these longitudes in the “Add or Remove Satellite” menu.

RE-PEAKING ON SATELLITE IF RIG HAS SETTLED

If you own a bus or other rig that settles over time, this option is for you. Instead of stowing and relocating the satellite, which is time consuming, you may simply choose “Re-Peaking” and the dish will begin to re-peak on the satellite to strengthen the signal. To get to the repeaking options, simply press the OFF button on the remote and the “Power Off Button” menu will appear.

NOTE – You must be on the satellite for this function to work. Re-Peaking only recenters the dish on the satellite.

ADDING AND REMOVING SATELLITES

Normally, your MotoSAT dish will come with 1 satellite location. You have the ability to add other satellites to your system, and then quickly move the dish to each of them any time you like.

To ADD a satellite, please go to the “Add or Remove Satellite” menu.

SAFETY STOWING OPTIONS

Your MotoSAT system has certain Stow features that you may desire to use or not. There are three options:

• You can automatically stow dish if the power goes off on the Satellite Receiver.

• You can automatically stow the dish if AC power is lost to the rig.

• You can automatically stow the dish of the signal is lost. This feature is good if you

accidentally move the rig without stowing the dish first.

To change any of these items, please go to the “Options” menu screen.

CHANGING DISH SIZE

Your installer normally sets this function. You have the option of choosing an 18” dish or a 24” dish. Default is 18”. This setting is found on the “Options” menu screen. (MiniDome is same as 18” dish).

CHANGING REMOTE CONTROL TYPE

Your installer normally sets this function. However, you may have purchased a new Satellite Receiver, in which case, you will need to tell the MotoSAT positioner which kind of Satellite Receiver you are now using. Holding the front panel button in for 30 seconds can also do this function. If the power button is held in for 30 seconds it will also erase satellites stored in memory. (See POWER pg. 4 for details).

To make this selection, please go to the “Options” menu screen.

TESTING DISH

A Test Dish function is automatically executed at time of installation. Any further selection of this feature will check all functional capabilities of the mount. If Test Dish fails, go to Trouble Shooting.

USING YOUR MotoSAT SYSTEM

There are four basic operations that you will use any time you want to watch television.

1. TURNING ON THE SYSTEM

2. FINDING SATELLITE

3. STOWING THE DISH

4. TURNING OFF THE SYSTEM

Of course there are many other functions you may perform, but for now, let’s focus on getting the TV working.

TURNING ON THE SYSTEM

Two things need to be turned ON in order for your system to function.

• The MotoSAT Positioner box

• Your television

NOTE: Your Satellite Receiver will be turned on by The MotoSAT Positioner when it needs to be turned on. The MotoSAT “ON” button illuminates blue when it is on. Obviously, the TV must be turned on.

When the system turns on, you should immediately see the MotoSAT Positioner Main Menu Screen seen below, if not, press “Menu” on your satellite receivers’ remote.

CHANGING RECEIVER OUTPUT TO CHANNEL 3 OR 4*

To change the output of your satellite receiver from 3 to 4 or back, simply (with FIND SATELLITE selected) press the 3 key on your remote for channel 3 and/or 4 for channel 4.

Note: DON’T FORGET TO CHANGE THE CHANNELS ON YOUR TV TO CORRESPOND TO THE CHANGE JUST MADE.

*Some OSD Positioners have a manual 3 / 4 switch in the back. If your system has this manual switch, then, you must do it manually.

+ 16 hidden pages