Page 1
ECM-S80
SERVICE MANUAL
Ver 1.0 2002. 02
SPECIFICATIONS
Type Electret condenser microphone
Cord ø 2.2 mm (3 /32 in.)OFC litz cord
(2 core shielded)
Length:Approx.70 cm (27 5 /8 in.)
Attached with gold plated L-shaped stereo
miniplug
Power source 2 way power supply system
plug-in power
alkaline manganese battery LR44 (1)
Dimensions Approx.54 × 11 × 86 mm (w/h/d)
(2 1 /4 × 7 /16 × 3 1 /2 in.)
Mass Approx.39 g (1 oz.)(including battery)
Frequently response
100 – 10,000 Hz
Directivity Unidirectional × 2
Output impedance
1.6 k Ω ± 30%
Sensitivity Open circuit output voltage level –40 ± 4 dB/Pa
0 dB =1 V /Pa,1,000 Hz
(1 Pa =10 µ bar =94 dB
Battery life Approx.80 hours (continuous operation)
Operating temperature range
0 °C – 40 °C (32 °F – 104 °F)
SPL
US Model
Canadian Model
AEP Model
E Model
)
9-873-538-01
2002B0200-1
© 2002.2
Design and specifications are subject to change without notice.
ELECTRET CONDENSER MICROPHONE
Sony Corporation
Personal Audio Company
Published by Sony Engineering Corporation
Page 2
ECM-S80
SECTION 1
SERVICING NOTES
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the
lead-free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed
with the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to
be applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set
to about 350°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder
may also be added to ordinary solder.
“REEL ASSY, CORD” INSTALLATION
1
Put the flexible board through the hole of the flexible holder.
2
Wind flexible board around the flexible holder.
Note :
Leave the flexible board for 20 to 30mm.
3
Attach the flexible holder to the "reel ASSY, cord".
4
Loosen flexible board doesn't seem to coil around the flexible holder.
Flexible board
1
Holder, flexible
Flexible board
20 to 30 mm
Holder, flexible
2
LOCA TING THE CONTROLS
1
2
3
4
SECTION 2
GENERAL
5
6
Connection cord
Knot part of connection cord
1 Cord retracting wheel
2 POWER switch
When the microphone is powered by plug-in power,turn its
own power off.
3 Battery check indicator
4 Microphone
5 Stereo miniplug
To the microphone jack of the recording equipment
6 Slide
3
4
Loosen flexible board
doesn't seem to coil
around the flexible holder.
Reel ASSY, cord
This section is extracted from
instruction manual.
2
Page 3
SECTION 3
DIAGRAMS
ECM-S80
3-1. PRINTED WIRING BOARD
1
MIC1
L
AMP BOARD
D1
RED
BLK
C3
A
B
: Uses unleaded solder.
2
SW1
C4
(PLUG IN POWER)
3 4 5
C6
R5
D2
1-682-765-
ALKALINE MANGANESE BATTERY
Note:
• X : parts extracted from the component side.
• b : Pattern from the side which enables seeing.
R6
RED
BLK
RED
LR44
1PC, 1.5V
R1R2R7
C5
SW1,2
POWER
OFFTON
(OUTPUT)
SW2
P1
D3
POWER
BLK
11
(11)
MIC2
R
3
Page 4
ECM-S80
3-2. SCHEMATIC DIAGRAM
MIC1
L
UDZSTE-17-4.7B
D1
C3
1
MIC2
R
ALKALINE MANGANESE BATTERY
LR44
1PC,1.5V
D2
UDZSTE-17-4.7B
2.5V
R1
3.3k
P1
(OUTPUT)
SW1,2
POWER
(PLUG IN POWER)
C5
47
C6
R6
47
470
2.5V
OFF
ON
D3
SML-310LT
POWER
SW1
C4
1
R7
100
3.3k
R2
SW2
10k
R5
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or
less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise specified.
• A : B+ Line.
• V oltages are dc with respect to ground under no-signal conditions.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Signal path.
F
4
Page 5
NOTE :
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “ * ”are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
14
13
P1
SECTION 4
EXPLODED VIEW
• The mechanical parts with no reference
number in the exploded views are not
supplied.
15
12
11
10
23
16
20
17
ECM-S80
18
19
9
21
22
8
1
7
1
6
2
3
1
2
1
5
4
2
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 3-234-433-01 FOOT, RUBBER
2 3-318-203-01 SCREW (B 1.7X6), TAPPING
3 3-234-420-01 TERMINAL, PLUS
4 3-234-425-01 CASE, BATTERY
5 3-234-430-02 SLEEVE
6 3-234-418-01 CASE, REAR
7 3-234-421-01 TERMINAL, MINUS
8 3-234-427-01 SLIDE, CORD
9 3-234-434-01 RING, SLIP
10 3-234-431-01 HOLDER, FLEXIBLE
11 A-3174-083-A REEL ASSY, CORD
12 3-234-422-01 LEVER, SWITCH
13 3-234-424-01 SPRING, LOCK
14 A-3174-081-A CASE ASSY, FRONT
15 3-234-423-01 KNOB, SWITCH
16 1-682-766-11 FLEXIBLE BOARD
* 17 1-682-765-11 AMPLIFIER BOARD
18 3-318-203-34 SCREW (B1.7X2.5), TAPPING
19 3-237-418-01 SPRING, GROUND COIL
20 A-3174-087-A UNIT ASSY (MIC L, R)
21 3-237-422-01 CUSHION
22 3-238-572-01 PLATE, GROUND
23 3-237-420-01 SHEET (E), DOUBLE-FACE ADHESIVE
P1 1-823-289-11 CORD, CONNECTION (2 CORE) (OUTPUT)
5
Page 6
ECM-S80
SECTION 5
AMPLIFIER
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
Note:
When indicating parts by reference
number, please include the board
name.
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* 1-682-765-11 AMPLIFIER BOARD
C3 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C4 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C5 1-119-663-11 TANTAL. CHIP 47uF 20% 2.5V
C6 1-119-663-11 TANTAL. CHIP 47uF 20% 2.5V
D1 8-719-083-60 DIODE UDZSTE-174.7B
D2 8-719-083-60 DIODE UDZSTE-174.7B
D3 8-719-074-30 DIODE CL-190UR-CD-T
****************
<CAPASITOR>
<DIODE>
ELECTRICAL PARTS LIST
• Due to standardization, replacements in the parts
list may be different from the parts specified in the
diagrams or the components used on the set.
• -XX, -X mean standardized parts, so they may
have some difference from the original one.
• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
• RESISTORS
All resistors are in ohms
METAL: Metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F : nonflammable
16 1-682-766-11 FLEXIBLE BOARD
20 A-3174-087-A UNIT ASSY (MIC L, R)
P1 1-823-289-11 CORD, CONNECTION (2 CORE) (OUTPUT)
***********************************************************
3-241-661-11 MANUAL, INSTRUCTION
• SEMICONDUCTORS
In each case, u: µ , for example:
uA...: µ A..., uPA...: µ PA..., uPB...: µPB...,
uPC...: µ PC..., uPD...: µ PD...
• CAPACITORS
uF : µ F
• COILS
uH : µ H
MISCELLANEOUS
***************
ACCESSORIES
************
(ENGLISH, FRENCH, GERMAN, SPANISH,
ITALIAN, PORTUGUESE)
<RESISTOR>
R1 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R2 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R5 1-216-833-11 METAL CHIP 10K 5% 1/16W
R6 1-216-817-11 METAL CHIP 470 5% 1/16W
R7 1-216-809-11 METAL CHIP 100 5% 1/16W
<SWITCH>
SW1 1-572-018-11 SWITCH, SLIDE (POWER)
SW2 1-572-018-31 SWITCH, SLIDE (POWER)
***********************************************************
6
Page 7
ECM-S80
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
7
Page 8
ECM-S80
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
V er. Date Description of Revision
1.0 2002.02 New
Loading...