The model and serial numbers are located at the rear of the unit.
Record the serial number in the space provided below. Refer to them
whenever you call upon your Sony dealer regarding this product.
Model No. DVP-NS325
Serial No.______________
For Customers in Canada
If this product is not working properly, please call 1-877-602-2008 for
Peace of Mind Warranty Replacement service.
For other product related questions please contact our Customer
Information Service Centre at 1-877-899-7669 or write to us at:
Customer Information Service 115 Gordon Baker Road, Toronto,
Ontario, M2H 3R6
To prevent fire or shock
hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock, do
not open the cabinet. Refer
servicing to qualified
personnel only.
CAUTION
The use of optical instruments with
this product will increase eye
hazard. As the laser beam used in
this CD/DVD player is harmful to
eyes, do not attempt to disassemble
the cabinet.
Refer servicing to qualified
personnel only.
This symbol is
intended to alert the
user to the presence
of uninsulated
within the product’s enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
maintenance (servicing)
instructions in the literature
accompanying the appliance.
“dangerous voltage”
This symbol is
intended to alert the
user to the presence
of important
operating and
CAUTION:
TO PREVENT ELECTRIC
SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT,
FULLY INSERT.
CAUTION
You are cautioned that any change
or modifications not expressly
approved in this manual could void
your authority to operate this
equipment.
Note
This equipment has been tested
and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of the FCC
Rules. These limits are designed to
provide reasonable protection
against harmful interference in a
residential installation. This
equipment generates, uses, and can
radiate radio frequency energy
and, if not installed and used in
accordance with the instructions,
may cause harmful interference to
radio communications. However,
there is no guarantee that
interference will not occur in a
particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be
determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
– Reorient or relocate the
receiving antenna.
– Increase the separation
between the equipment and
receiver.
– Connect the equipment into an
outlet on a circuit different
from that to which the receiver
is connected.
– Consult the dealer or an
experienced radio/TV
technician for help.
Thank you for purchasing this
Sony CD/DVD Player. Before
operating this player, please read
this manual thoroughly and retain
it for future reference.
2
Precautions
• The power requirements and power
consumption of this player are indicated on
the back of the player. Check that the
player’s operating voltage is identical with
your local power supply.
Power requirements and
power consumption t
On safety
• Caution – The use of optical instruments
with this product will increase eye hazard.
• To prevent fire or shock hazard, do not
place objects filled with liquids, such as
vases, on the apparatus.
• Should any solid object or liquid fall into
the cabinet, unplug the player and have it
checked by qualified personnel before
operating it any further.
On power sources
• The player is not disconnected from the AC
power source as long as it is connected to
the wall outlet, even if the player itself has
been turned off.
• If you are not going to use the player for a
long time, be sure to disconnect the player
from the wall outlet. To disconnect the AC
power cord, grasp the plug itself; never pull
the cord.
• Should the AC power cord need to be
changed, have it done at a qualified service
shop only.
On placement
• Place the player in a location with adequate
ventilation to prevent heat build-up in the
player.
• Do not place the player on a soft surface
such as a rug that might block the
ventilation holes.
• Do not place the player in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust, or mechanical
shock.
DVP–XXXX
00V 00Hz
NO.
00W
0-000-000-00
For the model supplied with the AC plug
adaptor
If the AC plug of your unit does not fit into
the wall autlet, attach the supplied AC plug
adaptor.
On operation
X
• If the player is brought directly from a cold
to a warm location, or is placed in a very
damp room, moisture may condense on the
lenses inside the player. Should this occur,
the player may not operate properly. In this
case, remove the disc and leave the player
turned on for about half an hour until the
moisture evaporates.
• When you move the player, take out any
discs. If you don’t, the disc may be
damaged.
On adjusting volume
Do not turn up the volume while listening to
a section with very low level inputs or no
audio signals. If you do, the speakers may be
damaged when a peak level section is played.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent
such as alcohol or benzine.
On cleaning discs
Do not use a commercially available cleaning
disc. It may cause a malfunction.
IMPORTANT NOTICE
Caution: This player is capable of holding a
still video image or on-screen display image
on your television screen indefinitely. If
you leave the still video image or on-screen
display image displayed on your TV for an
extended period of time you risk permanent
damage to your television screen. Plasma
Display Panel televisions and projection
televisions are susceptible to this.
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.
• Instructions in this manual describe the
controls on the remote. You can also use the
controls on the player if they have the same
or similar names as those on the remote.
• The meaning of the icons used in this
manual is described below:
IconMeaning
Functions available for DVD
VIDEOs and DVD-RWs/
DVD-Rs in video mode or
DVD+RWs/DVD+Rs
Functions available for VID EO
CDs, Super VCDs, or CD-Rs/
CD-RWs in video CD format
or Super VCD format
Functions available for music
CDs or CD-Rs/CD-RWs in
music CD format
Functions available for DATA
CDs (CD-ROMs/CD-Rs/CDRWs containing MP3* audio
tracks)
* MP3 (MPEG 1 Audio Layer 3) is a standard
format defined by ISO/MPEG which compresses
audio data.
Following Discs
Format of discs
DVD VIDEO
VIDEO CD
Music CD
The “DVD VIDEO” is a trademark.
Region code
Your player has a region code printed on the
back of the unit and only will play DVD
VIDEO discs (playback only) labeled with
identical region codes. This system is used to
protect copyrights.
DVP–XXXX
0-000-000-00
ALL
X
Region code
DVDs labeled will also play on this
player.
If you try to play any other DVD, the message
“Playback prohibited by area limitations.”
will appear on the TV screen. Depending on
the DVD, no region code indication may be
labeled even though playing the DVD is
prohibited by area restrictions.
00V 00Hz
NO.
00W
6
Example of discs that the player
cannot play
The player cannot play the following discs:
• All CD-ROMs (including PHOTO CDs)/
CD-Rs/CD-RWs other than those recorded
in the following formats:
– music CD format
– video CD format
– MP3 format that conforms to ISO9660*
Level 1/Level 2, or its extended format,
Joliet
• Data part of CD-Extras
• DVD-RWs in VR mode
• DVD-ROMs
• DVD Audio discs
• HD layer on Super Audio CDs
• Super VCDs in PAL format
* A logical format of files and folders on CD-
ROMs, defined by ISO (International Standard
Organization).
Also, the player cannot play the following
discs:
• A DVD with a different region code.
• A disc recorded in a color system other than
NTSC, such as PAL or SECAM (this player
conforms to the NTSC color system).
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane
tape or a sticker still left on it.
Note on playback operations of
DVDs and VIDEO CDs
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
Copyrights
This product incorporates copyright
protection technology that is protected by
method claims of certain U.S. patents, other
intellectual property rights owned by
Macrovision Corporation, and other rights
owners. Use of this copyright protection
technology must be authorized by
Macrovision Corporation, and is intended for
home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or
disassembly is prohibited.
Notes about the Discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
Notes
• Notes about DVD-RWs/DVD-Rs, DVD+RWs/
DVD+Rs or CD-Rs/CD-RWs
Some DVD-RWs/DVD-Rs, DVD+RWs/
DVD+Rs, or CD-Rs/CD-RWs cannot be played
on this player due to the recording quality or
physical condition of the disc, or the
characteristics of the recording device and
authoring software.
The disc will not play if it has not been correctly
finalized. For more information, see the operating
instructions for the recording device. Note that
discs created in the Packet Write format cannot be
played.
• Music discs encoded with copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it
in a car parked in direct sunlight as the
temperature may rise considerably inside
the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine,
thinner, commercially available cleaners, or
anti-static spray intended for vinyl LPs.
7
Index to Parts and Controls
For more information, refer to the pages indicated in parentheses.
Front panel
A [/1 (on/standby) button (24)
B Disc tray (24)
C Front panel display (9)
D (remote sensor) (14)
E A (open/close) button (24)
F Playback Dial (35)
G X (pause) button (25)
H x (stop) button (25)
I SURROUND button (41)
J PICTURE MODE button (44)
8
Front panel display
When playing back a DVD
Disc type
Lights up during
Repeat Play (33)
Playing status
Lights up when you can change the angle (46)
Current audio signal (40)
Current title/chapter or playing
time (39)
When playing back a VIDEO CD with Playback Control (PBC) (27)
Disc type
Playing status
Lights up during A-B
Repeat Play (33)
Current scene or playing time (39)
When playing back a CD, DATA CD (MP3 audio), or VIDEO CD (without PBC)
Playing status
Lights up during
Repeat Play (33)
Current track (39)
Disc type
Lights up when playing MP3 audio tracks (28)
Playing time (39)
,continued
9
Rear panel
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
R-AUDIO-L
LINE OUT
S VIDEO
COMPONENT VIDEO OUT
OUT
P
B
Y
P
VIDEO
R
A DIGITAL OUT (COAXIAL) jack (19)
(20) (21)
B LINE OUT L/R (AUDIO) jacks (18)
(19) (20)
C LINE OUT (VIDEO) jack (15)
D S VIDEO OUT jack (15)
E COMPONENT VIDEO OUT jacks
(15)
10
Remote
A TV [/1 (on/standby) button (51)
B
Z OPEN/CLOSE button (25)
C Number buttons (27)
The number 5 button has a tactile dot.*
D CLEAR button (30)
E SUBTITLE button (43)
F AUDIO button (40)
G ./> PREV/NEXT (previous/
next) buttons (25)
Hm/MSCAN/SLOW
buttons (35)
I X PAUSE button (25)
J H PLAY button (24)
The H button has a tactile dot.*
K C/X/x/c buttons (27)
L DISPLAY button (12)
M TOP MENU button (27)
N [/1 (on/standby) button (24)
O VOL (volume) +/– buttons (51)
The + button has a tactile dot.*
P TV/VIDEO button (51)
Q TIME/TEXT button (38)
R PICTURE MODE button (44)
S ANGLE button (46)
T SUR (surround) button (41)
U SEARCH MODE button (36)
V REPEAT button (33)
W INSTANT SEARCH/STEP
button (25, 36)
X INSTANT REPLAY/STEP
button (25, 36)
Y x STOP button (25)
Z ENTER button (22)
wj O RETURN button (27)
wk MENU button (27) (28)
* Use the tactile dot as a reference when operating
the player.
11
Guide to On-Screen
Displays (Control Bar)
The following explains the Control Bar. The
Control Bar is used for making adjustments to
the settings or displaying information during
playback.
The displayed contents differ according to the
type of disc being played. The numbers in
parentheses indicate reference pages.
Displaying the Control Bar during
playback
The following displays appear when the
DISPLAY button is pressed repeatedly
during playback. You can select the setting
that suits the current playback item and view
the related information.
◆Display 1
The following play modes 1~4 can be set.
The indicator lights up in blue when activated.
Example: When Repeat Play is selected. (The
display will differ when A-B Repeat Play is
set.)
CHAPTER
G TVS (41)
H “BNR” (43)
I “CUSTOM PICTURE MODE” (44)
J “DIGITAL VIDEO ENHANCER”
(45)
K “ANGLE” (46)
m
◆Display 3
The following playback information is
displayed.
Example: When playing a DVD.
DVD T41 – 8 T 1:01:57
L TIME/TEXT icon
M Title number of the DVD (36)
N Chapter number of the DVD (36)
O Playing time or remaining time (38)
A Repeat Play (33)
B Shuffle Play (32)
C Program Play (30)
D A-B Repeat Play (33)
E Unit being repeated in this example.
F Playback status (NPlayback,
XPause, xStop, etc.)
m
◆Display 2
The following play modes 7~K can be set.
The indicator lights up in blue when activated.
Example: When “TVS” is set.
12
m
◆Display 4 (DVD playback only)
DOLBY DIGITAL
P Format of the current audio signal (40)
3 / 2 .1
m
◆No display
m
◆Return to Display 1
Displaying the Control Bar in
stop mode
The following displays appear when the
DISPLAY button is repeatedly pressed
during stop mode. You can make basic
adjustments and customize the player to suit
your viewing preferences.
◆Display 1
The following settings can be made.
QUICK
◆Display 3
Shows the same information as Display 2
during playback.
m
◆Display 4
Shows the same information as Display 3
during playback.
DVD T41 – 8 T 1:01:57
A SETUP (53)
• Select QUICK to make the minimum
number of basic adjustments for using the
player.
• Select CUSTOM to make a full range of
adjustments.
• Select RESET to return the SETUP
adjustments to the default settings.
B PARENTAL CONTROL (47)
• Set this to limit the playback of selected
discs on this player.
m
◆Display 2
Shows the same information as Display 1
during playback.
CHAPTER
m
m
◆No display
m
◆Return to Display 1
13
Hookups
Hooking Up the Player
Follow Steps 1 to 6 to hook up and adjust the settings of the player.
Notes
• Plug cords securely to prevent unwanted noise.
• Refer to the instructions supplied with the components to be connected.
• You cannot connect this player to a TV that does not have a video input jack.
• Be sure to disconnect the power of each component before connecting.
You can control the player using the supplied remote. Insert two Size AA (R6) batteries by
matching the 3 and # ends on the batteries to the markings inside the compartment. When
using the remote, point it at the remote sensor on the player.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a
malfunction.
• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
14
Step 3: Connecting the Video Cords
Connect this player to your TV monitor, projector, or AV amplifier (receiver) using a video cord.
Select one of the patterns A through C, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver).
Hookups
A
INPUT
VIDEO
L
AUDIO
R
(yellow)
Audio/video cord
(supplied)
Component
video cord
(not supplied)
COMPONENT
VIDEO IN
C
Y
(green)
PB
(blue)
PR
(red)
TV, projector, or AV
TV, projector, or AV
amplifier (receiver)
amplifier (receiver)
(red)
to LINE OUT (VIDEO)
l : Signal flow
(yellow)
DIGITAL OUT
LINE OUT
PCM/DTS/
DOLBY DIGITAL
R-AUDIO-L
COAXIAL
to S VIDEO OUT
(green)
S VIDEO
COMPONENT VIDEO OUT
OUT
P
B
Y
P
VIDEO
R
CD/DVD player
S VIDEO cord (not supplied)
(blue)
to COMPONENT
VIDEO OUT
INPUT
S VIDEO
TV, projector, or AV
amplifier (receiver)
B
A If you are connecting to a video input jack
Connect the yellow plug of the audio/video cord (supplied) to the yellow (video) jacks. You will
enjoy standard quality images.
Yellow (Video)
White (L)
Red (R)
Yellow (Video)
White (L)
Red (R)
Use the red and white plugs to connect to the audio input jacks (page 18). (Do this if you are
connecting to a TV only.)
,continued
15
B If you are connecting to an S VIDEO input jack
Connect the S VIDEO cord (not supplied). You will enjoy high quality images.
C If you are connecting to a monitor, projector, or AV amplifier (receiver)
having component video input jacks (Y, P
Connect the component via the COMPONENT VIDEO OUT jacks using a component video
cord (not supplied) or three video cords (not supplied) of the same kind and length. You will
enjoy accurate color reproduction and high quality images.
B, PR)
Green
Blue
Red
Green
Blue
Red
When connecting to a wide screen TV
Depending on the disc, the image may not fit your TV screen. If you want to change the aspect
ratio, please refer to page 55.
Note
Connect the player directly to the TV. If you pass the player signals via the VCR, you may not receive a clear
image on the TV screen.
VCR
CD/DVD player
Connect
directly
TV
16
Step 4: Connecting the Audio Cords
Refer to the chart below to select the connection that best suits your system. Be sure to also read
the instructions for the components you wish to connect.
Select a connection
Select one of the following connections, through .
Components to be connectedConnectionYour setup (example)
Laboratories. “Dolby,” “Pro Logic,” and the
double-D symbol are trademarks of Dolby
Laboratories.
** “DTS” and “DTS Digital Out” are trademarks
of Digital Theater Systems, Inc.
and two speakers
*
B
C
D
(page 19)
(page 20)
(page 21)
,continued
17
A
Connecting to your TV
This connection will use your TV speakers for sound.
CD/DVD player
R-AUDIO-L
LINE OUT
S VIDEO
COMPONENT VIDEO OUT
OUT
P
B
Y
P
VIDEO
R
DIGITAL OUT
DOLBY DIGITAL
COAXIAL
PCM/DTS/
A
LINE OUT
(yellow)*
R-AUDIO-L
VIDEO
to LINE OUT L/R
(AUDIO)
l : Signal flow
* The yellow plug is used for video signals (page
15).
z Hint
When connecting to a monaural TV, use a stereomono conversion cord (not supplied). Connect the
LINE OUT L/R (AUDIO) jacks to the TV’s audio
input jack.
(white)
(red)
Audio/video
cord (supplied)
(yellow)*
(white)
(red)
to audio input
TV
18
Connecting to a stereo amplifier (receiver) and 2 speakers/Connecting to
CD/
B
an MD deck or DAT deck
If the stereo amplifier (receiver) has audio input jacks L and R only, use . If the amplifier
(receiver) has a digital input jack, or when connecting to an MD deck or DAT deck, use .
In this case, you can also connect the player directly to the MD deck or DAT deck without using
your stereo amplifier (receiver).
DVD player
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
R-AUDIO-L
LINE OUT
VIDEO
S VIDEO
OUT
COMPONENT VIDEO OUT
P
B
Y
P
R
B-1
B-2
Hookups
B-2
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
to DIGITAL OUT
(COAXIAL)
to coaxial digital input
[Speakers]
l: Signal flow
Front (L)
Front (R)
Coaxial digital
cord (not supplied)
Stereo amplifier (receiver)
Stereo audio cord
(not supplied)
or
(white)
MD deck/DAT deck
(white)
(red)
to LINE OUT L/R (AUDIO)
(red)
to audio input
LINE OUT
R-AUDIO-L
B-1
VIDEO
,continued
19
C
Connecting to an AV amplifier (receiver) having a Dolby Surround (Pro
Logic) decoder and 3 to 6 speakers
You can enjoy the Dolby Surround effects only when playing Dolby Surround audio or multichannel audio (Dolby Digital) discs.
If your amplifier (receiver) has L and R audio input jacks only, use . If your amplifier
(receiver) has a digital input jack, use .
C-2
C-1
CD/DVD player
C-2
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
to DIGITAL OUT
(COAXIAL)
to coaxial digital input
[Speakers]
R-AUDIO-L
LINE OUT
S VIDEO
OUT
VIDEO
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
Coaxial digital cord
(not supplied)
Amplifier (receiver) with Dolby
Surround decoder
COMPONENT VIDEO OUT
P
B
Y
P
R
Stereo
audio cord (not
supplied)
or
(white)
(red)
to LINE OUT L/R (AUDIO)
(red)(white)
to audio input
LINE OUT
R-AUDIO-L
[Speakers]
C-1
VIDEO
Rear (L)
Rear (R)
Subwoofer
l: Signal flow
Note
When connecting 6 speakers, replace the monaural
rear speaker with a center speaker, 2 rear speakers
and a subwoofer.
20
Center
Front (L)
Rear (mono)
Front (R)
Loading...
+ 46 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.