Page 1
DVP-C650D/C653D
RMT-D112A
SERVICE MANUAL
Photo: DVP-C650D
SPECIFICATIONS
CD/DVD player
Laser Semiconductor laser
Signal format system NTSC
Audio characteristics
Frequency response DVD (PCM 96 kHz): 2 Hz to 44 kHz
(±1 dB)*
DVD (PCM 48 kHz): 2 Hz to 22 kHz
(±0.5 dB)
CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio More than 115 dB (LINE OUT (AUDIO 1,
2) connectors only)
Harmonic distortion Less than 0.0025%
Dynamic range More than 100 dB (DVD)
More than 97 dB (CD)
Wow and flutter Less than detected value
(±0.001% W PEAK)
Outputs and inputs
Jack Output Load impedance
type level
LINE OUT Phono 2 Vrms Over 10 kilohms
(AUDIO 1, 2) jacks (at 50 kilohms)
DIGITAL OUT Optical –18 dBm Wave length: 660 nm
(OPTICAL) output
connector
DIGITAL OUT Phono 0.5 Vp-p 75 ohms terminated
(COAXIAL) jack
LINE OUT Phono 1.0 Vp-p 75 ohms,
(VIDEO 1, 2) jacks sync negative
S VIDEO OUT 4-pin Y: 1.0 Vp-p 75 ohms,
(1, 2) mini DIN sync negative
C: 0.286 Vp-p 75 ohms terminated
COMPONENT phono Y: 1.0 Vp-p 75 ohms,
VIDEO OUT jacks sync negative
(Y, PB/B-Y, PB/B-Y,
PR/R-Y) PR/R-Y:
0.7 Vp-p 75 ohms
PHONES Phone 12 mW 32 ohms
jack
5.1CH Phono 2 Vrms Over 10 kilohms
OUTPUT jacks (at 50 kilohms)
US Model
Canadian Model
E Model
DVP-C650D
PX Model
DVP-C653D
Jack Output Load impedance
type level
S-LINK Mini jack – –
MEGA Mini jack – –
CONTROL
AUDIO IN Phono 2 Vrms 47 kilohms
jack
General
Power requirements (indicated on the rear panel)
120 V AC, 60 Hz (C650D : US, Canadian)
110–240 V AC, 50/60 Hz
(C653D : E, C653D : PX)
Power consumption 18 W
Dimensions (approx.) 430 × 120 × 425 mm
(17 × 43/4 × 163/4 in.) (w/h/d)
incl. projecting parts
Mass (approx.) 6.1 kg (13 lb 7 oz)
Operating temperature 41°F to 95°F (5°C to 35°C)
Operating humidity 5% to 90%
Supplied accessories
• Audio/Video/S-link connecting cord (1) or Audio/Video connecting
cord (1)
• S video cord (1)
• Plug adaptor (1) (except for the USA/Canada models)
• Remote commander (remote) RMT-D112A (1)
• Size AA (R6) batteries (2)
* The signals from LINE OUT (AUDIO 1, 2) connectors and 5.1 ch L, R
connectors are measured. When you play the PCM sound tracks with
96 kHz sampling frequency, the output signals from the DIGITAL OUT
(OPTICAL, COAXIAL) are converted to 48 kHz (sampling frequency).
Design and specifications are subject to change without notice.
CD/DVD PLAYER
MICROFILM
Page 2
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them
out to the customer and recommend their replacement.
4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recommend their replacement.
5. Check the line cord for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
6. Check the B+ voltage to see it is at the values specified.
7. Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
To Exposed Metal
Parts on Set
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT -540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated A C milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63T rd are e x-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2V A C range ar e suit-
able. (See Fig. A)
AC
0.15 µF
1.5 k
Ω
Earth Ground
Voltmeter
(0.75 V)
Fig. A Using AC voltmeter to check AC leakage
WARNING!!
WHEN SERVICING, DO NO T APPR O A CH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION,
BE SURE TO OBSERVE FROM A DISTANCE OF
MORE THAN 25 cm FROM THE SURFACE OF THE
OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION:
The use of optical instrument with this product will increase eye
hazard.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS P AR UNE MARQUE !
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
– 2 –
Page 3
TABLE OF CONTENTS
Section Title Page Section Title Page
Service Note ............................................................................ 4
1. GENERAL
This Player Can Play the Following Discs .................... 1-1
Getting Started .............................................................. 1-1
Playing Discs ................................................................. 1-3
Using Var ious Functions with the Control Menu ........... 1-6
Settings and Adjustments ............................................. 1-12
Additional Information ................................................... 1-16
2. DISASSEMBLY
2-1. Case Removal ............................................................... 2-1
2-2. Front Panel Section Removal........................................ 2-1
2-3. MB-85 Board Removal .................................................. 2-1
2-4. AU-215 Board Removal ................................................ 2-1
2-5. Rear Panel Section Removal ........................................ 2-2
2-6. Table Ass’y Removal ..................................................... 2-2
2-7. Rotary Motor Ass’y (M951) Removal ............................ 2-2
2-8. Chassis Ass’y ................................................................ 2-2
2-9. Loading Motor Ass’y (M991) Removal.......................... 2-3
2-10. BU Holder Ass’y Removal............................................. 2-3
2-11. TK-53 Board Removal................................................... 2-3
2-12. Optical Pick-up Removal ............................................... 2-3
2-13. Internal View.................................................................. 2-4
2-14. Circuit Boards Location................................................. 2-5
FL-104 (FUNCTION SWITCH), SW-321 (FUNCTION
SWITCH) and CK-88 (CONNECTION)
Schematic Diagram ....................................................... 4-51
FL-104 (IF CON) Schematic Diagram .......................... 4-53
FR-154 (IR/POWER SWITCH)
Printed Wiring Boards and Schematic Diagram ........... 4-55
HP-114 (HEADPHONE) Printed Wiring Boards
and Schematic Diagram................................................ 4-57
LM-59 (LOADING MOTOR), CK-81 (DRIVE)
Printed Wiring Boards ................................................... 4-59
LM-59 (LOADING MOTOR), CK-81 (DRIVE)
Schematic Diagram ....................................................... 4-61
HS-034SF (SWITCHING REGULATOR)
Printed Wiring Board ..................................................... 4-63
HS-034SF (SWITCHING REGULATOR)
Schematic Diagram ....................................................... 4-65
HS-034SU (SWITCHING REGULATOR)
Printed Wiring Board ..................................................... 4-67
HS-034SU (SWITCHING REGULATOR)
Schematic Diagram ....................................................... 4-69
5. IC PIN FUNCTION DESCRIPTION
5-1. System Control Pin Function
(MB-85 Board IC202) .................................................... 5-1
6. TEST MODE
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram .................................................. 3-1
3-2. RF/Servo Block Diagram .............................................. 3-3
3-3. Signal Process/Video Block Diagram ........................... 3-5
3-4. System Control Block Diagram ..................................... 3-7
3-5. Audio (1) Block Diagram ............................................... 3-9
3-6. Audio (2) Block Diagram ............................................... 3-11
3-7. Interface Control Block Diagram ................................... 3-13
3-8. Power Block Diagram .................................................... 3-15
4. PRINTED WIRING BOARDS AND SCHEMATIC
DIAGRAMS
4-1. Frame Schematic Diagram ........................................... 4- 3
4-2. Printed Wiring Boards and Schematic Diagrams ......... 4-7
TK-53 (RF/SERVO) Printed Wiring Board .................... 4-7
TK-53 (RF/SERVO) Schematic Diagram ...................... 4-11
SE-91 (SENSOR), LE-24 (LED)
Printed Wiring Boards and Schematic Diagram ........... 4-13
MB-85 (SIGNAL PROCESS)
Printed Wiring Board ..................................................... 4-15
MB-85 (AV DECODER) Schematic Diagram................ 4-19
MB-85 (SDRAM) Schematic Diagram .......................... 4-21
MB-85 (SERVO DSP) Schematic Diagram................... 4-23
MB-85 (DRIVE) Schematic Diagram ............................ 4-25
MB-85 (ARP) Schematic Diagram ................................ 4-27
MB-85 (SYSTEM CONTROL)
Schematic Diagram ....................................................... 4-29
MB-85 (HGA) Schematic Diagram................................ 4-31
MB-85 (CLOCK GENERATOR/AUDIO DSP/
V EQ/NR) Schematic Diagram...................................... 4-33
MB-85 (DAC) Schematic Diagram ................................ 4-35
MB-85 (BIAS) Schematic Diagram ............................... 4-37
AU-215 (AUDIO/VIDEO BUFFER)
Printed Wiring Board ..................................................... 4-39
AU-215 (AUDIO) Schematic Diagram ........................... 4-43
AU-215 (VIDEO BUFFER) Schematic Diagram ........... 4-45
FL-104 (FUNCTION SWITCH/IF CON), SW-321
(FUNCTION SWITCH) and CK-88 (CONNECTION)
Printed Wiring Boards ................................................... 4-47
6-1. General Description ...................................................... 6-1
6-2. Starting T est Mode ........................................................ 6-1
6-3. Syscon Diagnosis .......................................................... 6-1
6-4. Drive Auto Adjustment .................................................. 6-5
6-5. Drive Manual Operation ................................................ 6-7
6-6. Mecha Aging ................................................................. 6-9
6-7. Emergency History ........................................................ 6-9
6-8. Version Information ....................................................... 6-10
6-9. Video Level Adjustment ................................................ 6-10
7. ELECTRICAL ADJUSTMENTS
7-1. Power Supply Adjustment ............................................. 7-1
1. Power Supply Check
(HS-034SF/034SU BOARD) ......................................... 7-1
7-2. Adjustment of Video System ......................................... 7-2
1. Video Level Adjustment (MB-85 BOARD) .................... 7-2
2. S-terminal Output Check (MB-85 BOARD) .................. 7-2
3. Checking Component Video Output B-Y
(MB-85 BOARD)............................................................ 7-2
4. Checking Component Video Output R-Y
(MB-85 BOARD)............................................................ 7-2
5. Checking Component Video Output Y
(MB-85 BOARD)............................................................ 7-3
6. Checking S Video Output S-C (MB-85 BOARD) .......... 7-3
7-3. Adjustment Related Parts Arrangement ....................... 7-4
8. REPAIR PARTS LIST
8-1. Exploded Views ............................................................. 8-1
8-1-1. Main Assembly ......................................................... 8-1
8-1-2. Front Panel Assembly .............................................. 8-2
8-1-3. Table Assembly ........................................................ 8-3
8-1-4. Chassis Assembly.................................................... 8-4
8-2. Electrical Parts List ....................................................... 8-5
– 3 –
Page 4
SERVICE NOTE
1. DISASSEMBLY
• This set can be disassembled in the order shown below.
Set
Case
(Page 2-1)
Front panel section
(Page 2-1)
Table ass’y
(Page 2-2)
Rotary motor ass’y
(M951) (Page 2-2)
Rear panel section
Loading motor ass’y
(M991) (Page 2-3)
2. NOTE ON REMOVE THE CASE
1) Remove seven tapping screws. (See Fig. 1)
2) Open the side of case. (See Fig. 1)
3) Remove the case as lift straight. (See Fig. 1)
(Page 2-2)
Chassis ass’y
(Page 2-2)
MB-85 board
(Page 2-1)
BU holder ass’y
(Page 2-3)
TK-53 board
(Page 2-3)
AU-215 board
(Page 2-1)
Optical pick-up
(Page 2-3)
3. DISC REMOVAL PROCEDURE
(at POWER OFF)
1) Insert a flat-blade screwdriver into a hole at the bottom, and
rotare the cam gear in direction A. (See Fig. 2)
Two tapping screws
Case
Fig. 1
Three tapping screws
Two tapping screws
Cam gear
Table
Hole
A
Fig. 2
– 4 –
Page 5
4. NOTE ON MOUNTING GEARS
1) Mount the gear (U/D). (See Fig. 3.)
2) Rotate the gear (U/D) in the direction of the arrow.
(down position) (See Fig. 3.)
Gear (U/D)
Fig. 3
6) Mount the lock lever (See Fig. 5.)
7) Mount the spring (lock lever). (See Fig. 5.)
Spring
(lock lever)
Lock lever
Gear
(main)
Spring
(lock lever)
Lock lever
3) Align triangle marks of the rotary encoder. (See Fig. 4.)
4) Escape the set lever. (See Fig. 4.)
5) Connect the boss of the gear (main) with the groove of the
rotary encoder and mount the gear (main). (See Fig. 4.)
Gear (main)
BU
Boss
Set lever
Groove
Rotary encoder
Fig. 5
8) Rotate the gear (main) in the direction of the arrow A by 90°
turn. (Gear (U/D) is up position.) (See Fig. 6.)
9) Mount the Gear (rev). (See Fig. 6.)
10) Fix three stopper washers on the groove of shafts.
(See Fig. 6.)
Groove
*
Stopper washer
Gear (rev)
**
Shaft
Two stopper
washers
Gear (main)
A
Gear (U/D)
Fig. 4
Align triangle marks.
Fig. 6
– 5 –
Page 6
SECTION 1
GENERAL
DVP-C650D/C653D
This section is extracted from instruction
manual (3-867-237-11)
1-1
Page 7
1-2
Page 8
1-3
Page 9
1-4
Page 10
1-5
Page 11
1-6
Page 12
1-7
Page 13
1-8
Page 14
1-9
Page 15
1-10
Page 16
1-11
Page 17
1-12
Page 18
1-13
Page 19
1-14
Page 20
1-15
Page 21
1-16
Page 22
1-17 E
1-17
Page 23
DVP-C650D/C653D
4 Three flat cables
(CN004, 005, 007)
5 Flat cable
(CN009)
3 Connector
(CN001)
2 Two flat cables
(CN002, 003)
8 Two screws
(B3) (with ring)
1 Flat cable
(CN006)
6 Rivet
7 Holder
9 MB-85 board
1 Connector
(CN401)
3 Three flat cables
(CN004, 005, 007)
2 Connector
(CN304)
5 Two screws
(B3)
4 Nine screws
(B3)
6 AU-215 board
SECTION 2
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
2-1. CASE REMOVAL 2-3. MB-85 BOARD REMOVAL
4 Case
1 Two tapping screws
2 Three tapping
screws
3 Two tapping screws
2-2. FRONT PANEL SECTION REMOVAL 2-4. AU-215 BOARD REMOVAL
1 Five screws
(B3) (with ring)
2 Shield case
4 Draw out
!¡ Two screws
(B3)
0 Screw (B3)
5 Tray cover
ass’y
!™ Claw
the table.
!£ Two Claws
6 Flat cable
(CN006)
!∞ Front panel section
A
7 Connector
(CN401)
!¢ Claw
3 Rotate the cam gear
in the direction of
the arrow A.
8 Connector
(CN902)
9 Screw (B3)
2-1
Page 24
2-5. REAR PANEL SECTION REMOVAL
2-7. ROTARY MOTOR ASS’Y (M951)
REMOVAL
2 Two flat cables
(CN002, 003)
1 Flat cable
(CN006)
8 Two screws
(B3)
3 Connector
(CN401)
4 Connector
6 Flat cable
!™ Rear panel section
(CN001)
!º Claw
(CN009)
7 Connector
(CN101)
5 Connector
(CN304)
9 Screw
(B3)
!¡ Claw
1 Tapping screw
(M3 × 12)
5 Bracket (RM) ass’y
7 Two screws
(B2.6 × 3)
2 Table (rotary)
4 Two screws
(B3)
6 Belt (RM)
3 Connector
(CN801)
8 Rotary motor ass’y
(M951)
2-6. TABLE ASS’Y REMOVAL 2-8. CHASSIS ASS’Y
2 Two brackets
(guide B1)
1 Two screws
(B3)
5 Table ass’y
4 Two brackets
(guide B1)
6 Flat wire
(CN656)
3 Two screws
(B3)
1 Four screws
(B3)
3 Chassis ass’y
2 Four screws
(B3)
2-2
Page 25
2-9. LOADING MOTOR ASS’Y (M991)
1 Flexible board
(CN002)
2 Flexible board
(CN001)
3 Screw
(B3)
5 TK-53 board
4 Claw
2 Flexible board
(CN001)
4 Optical pick-up
3 Three step screws
1 Flexible board
(CN002)
REMOVAL
4 Screw (B3)
5 Loading motor ass’y
(M991)
1 Belt (timing)
3 Harness
2-11. TK-53 BOARD REMOVAL
2 Connector
2-10. BU HOLDER ASS’Y REMOVAL
3 Bracket (CP)
5 BU holder ass’y
1 Two screws
(B3)
2-12. OPTICAL PICK-UP REMOVAL
2 Two screws
(B3)
4 Screw
(M3 × 12)
2-3
Page 26
2-13. INTERNAL VIEWS
Optical pick-up (KHM-220AAA/J1RP)
8-820-081-03
M951
Rotary motor ass’y
(turn table)
A-6062-080-A
PH801
Disc presence detection sensor
8-749-924-30
PH802
Turn table position
detection sensor
8-749-924-18
M991
Loding motor ass’y
A-4604-834-A
2-4
Rotary encoder
(loading)
1-466-996-21
Page 27
2-14. CIRCUIT BOARDS LOCATION
MB-85
(SIGNAL PROCESS/SERVO)
LM-59
(LOADING MOTOR)
FR-154
(IR/POWER SWITCH)
TK-53
(RF/SERVO)
AU-215
(AUDIO/VIDEO BUFFER)
SE-91
(SENSOR)
POWER BLOCK
HS-034SU: US, Canadian
HS-034SF: E, PX
(SWITCHING REGULATOR)
HP-114
(HEADPHONE)
SW-321
(FUNCTION SWITCH)
LE-24
(LED)
CK-88
(CONNECTION)
CK-81
(DRIVE)
FL-104
(FUNCTION SWITCH/IF CON)
2-52-5 E
Page 28
3-1. OVERALL BLOCK DIAGRAM
DVP-C650D/C653D
SECTION 3
BLOCK DIAGRAMS
BASE UNIT
KHM-220AAA
OPTICAL DEVICE
DVD/CD
FOCUS
TRACKING
TILT
MOTOR
PDIC
COIL
COIL
MB-85 BOARD
(SEE PAGE 4-21 to 35)
IC202
V EQ/NR
PDO 0-7
IC502
Parallel BUS
PDI 0-7
ACH12,ACH34,
ACH56,
BCK, LRCK
IC204
1M SRAM
IC501
AUDIO DSP
IC205
16M FLASH
VIDEO V,
VIDEO Y,
VIDEO C
VIDEO G/Y,
VIDEO R/B-Y,
VIDEO B/R-Y
SPDIF
IC902
AUDIO 2CH DAC
IC304
16M DRAM
TK-53 BOARD
(SEE PAGE 4-11)
SD 0-7
RF
IC001
DVD/CD RF AMP
DIGITAL SERVO
FOCUS COIL/
TRACKING COIL/
TILT MOTOR
IC801
DRIVE
M
DVD RF,
CD RF
IC303
ARP2
IC701
SERVO DSP
CDDOUT, CDDATA,
CDBCK, CDLRCK
IC601
HGA
IC402, 403
16M SDRAM
IC401
AV DECODER
SYSTEM CONTROL
AU-215 BOARD
(SEE PAGE 4-43,45)
HEADPHONE
AUDIO LT,
AUDIO RT
IC321
VIDEO
BUFFER
IC303
VIDEO
BUFFER
IC401
AMP
IC431
LPF
IC505
HP-114 BOARD
(SEE PAGE 4-58)
RY301
VIDEO 1, 2
S VIDEO 1, 2
COMPONENT
VIDEO
DIGITAL
OUT
PHONES
AUDIO
OUT1, 2
SLED
MOTOR
SPINDLE
MOTOR
LM-59 BOARD
(SEE PAGE 4-61)
M991
LOADING
MOTOR
M951
TURN TABLE
MOTOR
LE-24 BOARD
(SEE PAGE 4-14)
IC201
4K EEP ROM
M
M
ROTARY
ENCODER
LOADING)
IC802
SPINDLE/SLED/
MOTOR DRIVE
CK-81 BOARD
(SEE PAGE 4-61)
IC602
16M NAND-F
SW-321 BOARD
(SEE PAGE 4-51)
SWITCH
ND201
M
IC652
TURN TABLE/
SE-91 BOARD
(SEE PAGE 4-14)
LOADING
MOTOR DRIVE
JOG UNIT
M
PH801, 802
SENSOR
FR-154 BOARD
(SEE PAGE 4-55)
Serial BUS
FL-104 BOARD
(SEE PAGE 4-51,53)
FL DRIVER
SWITCH
SWITCH
IC205
IC201
IF CON
IC203
S-LINK
+5V
–12V
EVER5V
CK-88 BOARD
(SEE PAGE 4-51)
IC905-907
AUDIO 5.1CH DAC
+3.3V
+5V
A+12V
M+12V
AUDIO L, R
AUDIO LS, RS
AUDIO C, LFE
+3.3V
+5V
+12V
–12V
EVER5V
IC502, 541, 571
LPF
HS-034SF BOARD
(SEE PAGE 4-65)
HS-034SU BOARD
(SEE PAGE 4-67)
RY302
SW REG
AUDIO
IN
5.1CH OUTPUT
S-LINK
MEGA
CONTROL
05
3-1 3-2
Page 29
DVP-C650D/C653D
3-2. RF/SERVO BLOCK DIAGRAM
IC0011(CD play)
500mV/DIV 500ns/DIV
880mVp-p
BASE UNIT
KHM-220AAA
OPTICAL DEVICE
MOTOR
SPINDLE
MOTOR
IC0011(DVD play)
200mV/DIV 100ns/DIV
536mVp-p
DVD/CD
PDIC
DVD/CD
LD MODULE
COIL
TRACKING
COIL
TILT
M
INLIMIT
SENSOR
M
SLED
M
MOTOR
RF
A-D
E-H
VC
PD
LD
VR
FCSFOCUS
TRK
TIA, TIB
INLIM
SPM
SLA, SLB
TK-53 BOARD
(SEE PAGE 4-11)
CN001
7
9
10
16
17
8
11
15
18
13
4
2
5
19
20
21
22
CN002
10
ı
13
2
8
9
4
ı
7
Q001
LD DRIVE
200mV/DIV 500ms/DIV
IC001%¢(DVD play)
500mV/DIV 100ns/DIV
1.5Vp-p
IC001
DVD/CD RF AMP
DIGITAL SERVO
RF IP
1 54
9
ı
A-D
12
5
ı
A2-D2
8
13
E-H
ı
16
VC
17
19
PD
20
LD
IC001@ª(DVD play)
592mVp-p
IC001%¢(CD play)
500mV/DIV 500ns/DIV
1.5Vp-p
SIGO
40
FE
39
TE
29
PI
26
MIRR
32
TZC
33
VCI
SCLK
43
SWD
ı
SRD
46
SDEN
27
FDCHG
42
HOLD2
31
DFT
IC001@ª(CD play)
200mV/DIV 20ms/DIV
448mVp-p
Q002
CN004
17
9
8
7
3
5
6
SSCK, SSWD,
11
ı
14
15
4
6
7
4
5
15
ı
18
8
13
14
9
ı
12
RF+
FE
TE
PI
MIRR
TZC
2VC
SSRD, SSCS
SSDFCT
SSDFCTI
FCS
TRK
TIA, TIB
INLIM
SPM
SLA, SLB
MB-85 BOARD(1/6) (SEE PAGE 4-23,25,31)
IC001$º(DVD play)
100mV/DIV 50ms/DIV
10
11
12
16
14
13
15
12
13
14
15
11
10
2
5
ı
8
4
1
ı
4
5
6
7
ı
CN002CN003
2VC
CN003
180mVp-p
IC001#ª(DVD play)
500mV/DIV 50ms/DIV
1.3Vp-p
13
14
11
12
15
ı
18
15
16
11
ı
14
IC001$º(CD play)
500mV/DIV 50ms/DIV
860mVp-p
IC001#ª(CD play)
500mV/DIV 200ms/DIV
1.7Vp-p
IC801
FOCUS
COIL
DRIVE
TRACKING
COIL
DRIVE
TILT
MOTOR
DRIVE
IC802
SPINDLE
MOTOR
DRIVE
SLED
MOTOR
DRIVE
2
3
9
5
6
7
20
23
26
26
20
2
3
5
6
9
FCD
TRD
TLTA, TLTB
SLDA, SLDB,
STVC
Q801
IC702 (1/2)
3 1
IC803 (1/2)
12
13
IC701^ª(DVD play)
500mV/DIV 50ms/DIV
1.4Vp-p
IC701^ª(CD play)
500mV/DIV 200ms/DIV
1.7Vp-p
IC701^•(DVD play)
100mV/DIV 5ms/DIV
180mVp-p
IC701^•(CD play)
500mV/DIV 50ms/DIV
860mVp-p
DVD RF
CD RF
SIGNAL PROCESS,
22
Q802, 803
GAIN
CONTROL
FG REF
VRBA,
VRB 0-3
GIO 10
HINT
HRD
HWR
HCS
EA 0, 1
HD 0-7
74
81
84
93
96
39
128
117
120
122
125
IC702 (2/2)
7 5
1
2
3
4
5
ı
ı
68
ADC1
69
ADC0
67
ADC2
66
ADC3
65
ADC4
21
TRIN
20
TRREF
23
FGIN
41
GIO 5-8
ı
44
38 GIO 11
28
DFCTI
80
FCD
TRD
TLTA,TLTB
SLDA, SLDB,
STVC
TILT MUTE
FGMODE
14
85
92
97
48
49
7
ı
9
46
50
IC6510
DAB 2,3
DAB 0, 1
GIO 1, 2
PWM 0-2
GIO 4
GIO 0
IC701
SERVO DSP
RS
26 108
X2/CLKIN
LOCK
MDS0
MDP0
+3.3V
FCSON
XSDPIT
XSDPRD
XSDPWR
XSDPCS
HA0, 1
HD8-15
N27MSDP
XSDPRST
X3VRST
SPDLSTOP
SPGAIN
XDRV MUTE
LDMM/DMM
VIDEO
(SEE PAGE 3-5)
SYSTEM
CONTROL
(SEE PAGE 3-7,8)
LM-59 BOARD
(SEE PAGE 4-61)
M991
LOADING
MOTOR
05
SE-91 BOARD
(SEE PAGE 4-14)
M951
TURN TABLE
MOTOR
B991
M
1
2
1
2
PH801
DISC PRESENCE
DETECTION SENSOR
PH802
TURN TABLE POSITION
DETECTION SENSOR
M
ROTARY
ENCODER
(LOADING)
1
2
CN801
CN802
DSENS
4
TSENS
2
TM
6
7
LMLM
1
2
S1
3
S2
4
S3
6
4
6
1
2
1
2
3
4
6
CN656
B651
CK-81 BOARD
(SEE PAGE 4-61)
IC652
TURN TABLE
14
MOTOR
16
DRIVE
LOADING
11
MOTOR
13
DRIVE
IC651
OSC
CN651
11
1
TRMP, TRMM
6
7
CKMP, CKMM
8
9
4
3
2
DSW1
TSW1
CKSW1
CKSW2
OCSW1
3
13
7
8
5
6
10
11
12
Q656
21
22
4
5
Q653, 654
SWITCH
Q651, 652
SWITCH
CN009
11.6Vp-p (H)
DSW1
TSW1
TRMP
TRMM
CKMP
CKMM
CKSW1
CKSW2
OCSW1
SYSTEM
CONTROL
(SEE PAGE 3-8)
+3.3V
+5V
IC803 (2/2)
5 7
10
3 1
2.5VC
8
2VC
1.6VC
3-3 3-4
Page 30
3-3. SIGNAL PROCESS/VIDEO BLOCK DIAGRAM
MB-85 BOARD(2/6)
(SEE PAGE 4-19,21,27,33,35)
IC303!¶(DVD play)
500mV/DIV 200ns/DIV
RF, SERVO
(SEE PAGE 3-4)
SYSTEM
CONTROL
(SEE PAGE 3-7,8)
IC303!ª(CD play)
1.6Vp-p
DVD RF
CD RF
MDS0
MDP0
LOCK
DFCT
NORF
LOCK
FWON
MD2
MUTE
XARPWR
XARPRD
XARPIT
XARPCS
XARPWT
XCS2
XCS3
XRD
XWRH
XAVDIT
XAVDWT
DACK0
DREQ0
DACK1
DREQ1
500mV/DIV 100ns/DIV
1.6Vp-p
136-139
141-144
RFIN1
RFIN2
MDS0
MDP0
DFCT
NORF
LOCK
FWON
MD2
MUTE
XWR
XRD
XINT
XCS
XWAT
XRST
87
121
XARPRST
146 147
MCKI
123
33MARP
17
19
49
52
55
56
58
59
113
111
60
61
83
84
86
MA 0-9
SCKI
IC304
16M DRAM
MD 00-15
154-157
159-162
164-167
169-172
IC303
ARP2
A 0-7
73-76 79-82
XRAS, XOE
XMWR, XCAS,
148
150-152
63-68 70 71
SD 0-7
D 0-7
97
SD 0-7
98
100
ı
105
SDCK, SDEF,
91
XSHD, XSAK, XSRQ
93
ı
96
CDDOUT, CDDATA,
107
CDBCK, CDLRCK
ı
110
38
43
45
46
47
51
29
32
166
167
193
194
196
198
202
ı
ı
ı
ı
DAD 0-11
105-108
110-113
115-118
DT 0-7 I
103 19 36
XAVDRST
RSTIN
256FS30
ACLKI
IC402, 403
16M SDRAM
DDT 0-15
134 135
137 138
140 141
143 144
146 147
149 150
152 153
155 156
CRPCLKI
CLKI
160 163
27M30
33M30
IC502
V EQ/NR
YI 0-7
CLK, CKE,
DQML, DQMU,
CS, WE, CAS, RAS
120-123
125 127
129-132
SCLKIN
168-170 172-178 180-187 189-192 2-5 7-10 12-15 205-208
PDO 0-7
PDO 0-7
IC401
AV DECODER
IC401^¡
1,1Vp-p(H)
HAD 0-21 I
YO 0-7
60-6711-18
PDI 0-7
75-78 80-8386-89 91-94
IC401^™
816mVp-p(H)
97 98
FLDO
72 73 98 99
PDI 0-7
IC401%¶
728mVp-p(H)
IC401^∞
1.2Vp-p(H)
VSYNCI
HSYNCO
FLDO
HD 0-15
CLK27I
XRST
SDI
HSYNCI
31 29
SDOUT
HSYNCON
NR-SDOUT
CS
SENO
NR-SENO
100
93
G/Y OUT
R/B-Y OUT
B/R-Y OUT
COMP OUT
ACH12O
ACH34O
ACH56O
Y OUT
C OUT
LRCKO
BCKO
70
VREFI
58
54
57
65
61
62
21
22
23
25
26
RV401
VIDEO
LEVEL
ADJ
IC401%•
1.0Vp-p(H)
X57RST
27M57
IC401%¢
720mVp-p(H)
CN004
CN005
VIDEO G/Y
4
VIDEO R/B-Y
2
VIDEO B/R-Y
6
1
3
5
8
6
VIDEO V
VIDEO Y
VIDEO C
V MUTE
VS
AU-215 BOARD(1/3)
(SEE PAGE 4-43,45)
CN303
4
6
2
IC3214
1.2Vp-p(H)
IC3212
1.1Vp-p(H)
CN301
28
26
24
21
23
VIDEO BUFFER
7 10
4
2 15
1
VIDEO BUFFER
4 13
2
7 10
1
Q321, 322
DC ON/OFF
IC303
IC321
DVP-C650D/C653D
J303
Y
COMPONENT
J505
Y
C
Y
C
PB/B-Y
PR/R-Y
VIDEO OUT1
VIDEO OUT2
S VIDEO OUT1
S VIDEO OUT2
VIDEO OUT
13
IC321!£
2.4 Vp-p(H)
15
INTERFACE
CONTROL
(SEE PAGE 3-14)
05
XARPRST
XAVDRST
X57RST
33MARP
256FS30
33M30
27M30
27M57
VS
HA 0-21
HD 0-15
V MUTE
HA 0-7
HD 8-15
CDDOUT, CDDATA, CDBCK, CDLRCK
HA 0-21
HD 0-15
ACH12
ACH34
ACH56
LRCK
BCK
CDDOUT
CDDATA
CDBCK
CDLRCK
AUDIO 1
(SEE PAGE 3-XX)
IC3217
860mVp-p(H)
IC3210
1.8mVp-p(H)
IC321!∞
2.0Vp-p(H)
3-5 3-6
Page 31
DVP-C650D/C653D
3-4. SYSTEM CONTROL BLOCK DIAGRAM
MB-85 BOARD(3/6)
(SEE PAGE 4-29,31,33)
IC204
1M SRAM
IC205
16M FLASH
SIGNAL PROCESS,
VIDEO
(SEE PAGE 3-5)
RF, SERVO
(SEE PAGE 3-4)
05
AUDIO 2
(SEE PAGE 3-11)
HA 0-21
HD 0-15
HA 0, 1
HD 8-15
X3VRST
GAIN1
GAIN2
IC202(™
2.4Vp-p(12.5MHz)
X201
12.5MHz
X001
27MHz
IC0016
4.2Vp-p(27.0MHz)
HA 0-21
HD 0-15
42 44-64
25-39 41
A 01-21
D 16-31
IC001!¢(DVD play)
4.2Vp-p(25.3MHz)
IC001!¢(CDplay)
4.7Vp-p(22.5MHz)
IC001!¶
IC001
PLL
MD
ML
XT1
SYSTEM CONTROL
SCKO3
17
14
SCKO2
12
SCKO1
2
PB6
3
PB7
91
X1
92
X0
P66
PB4
66 100 99 98
CKSEL
DVD/CD
DVD:5.8Vp-p(36.5MHz)
CD:5.1Vp-p (33.8MHz)
19
1
6
IC001!™
4.6Vp-p(33.8MHz)
SI1
SIO
SC0
SO1
SI1
SC0
SO1
IC2025
4Vp-p(25.3MHz)
PB2
PB3
1
3 5
IC004
5
2
7
SC1
SC1
IC003
IC0042,5,7
4.2Vp-p(26.9MHz)
SO0
76 77 78 79 80 89 14 97
SI0
SO0
IC202
3
6
1
CS0L
XFRRST
RST
7
PB1
DACK1
DACK0
DREQ1
DREQ0
CS1
CS4
WR0
WR1
RDY
INT1
INT3
PF7
CLK
CS2
CS3
INT0
CS0
RD
11
10
22
23
24
19
94
88
83
95
84
85
86
87
IC207
POWER ON
4 5
RESET
7
5
9
8
IC0035,7
DVD:6.2Vp-p(37.0MHz)
CD:5Vp-p(33.6MHz)
XDACS0
XDACS1
384FSDA
384FS01
27M01
256FS30
33MARP
33M30
27M57
27M30
N27MSDP
HA 1-16
HD 0-15
+3.3V
CE
WE
CS
XRD
XWRH
XCS2
XCS3
SIGNAL PROCESS,
XAVDIT
VIDEO
DACK1
(SEE PAGE 3-5)
DACK0
DREQ1
DREQ0
AUDIO 1
(SEE PAGE 3-9)
SIGNAL PROCESS,
VIDEO
(SEE PAGE 3-5)
RF, SERVO
(SEE PAGE 3-4)
CS, WE,
OE, UB, LB
SIGNAL PROCESS,
VIDEO
(SEE PAGE 3-5)
HA 1-20
SC0
SO0
SI0
WE, RY/BY,
HD 0-15
IC201
4K EEPROM
4 3
5 8
6 1
SK
DI
DO
XARPRST
XARPIT
XARPWT
XARPWR
XARPRD
XARPCS
XAVDWT
XAVDRST
X57RST
CS
WC
R/B
MUTE
MD2
NORF
DFCT
FWON
LOCK
VS
N27MHGA
OE, CE
WE, UB, LB,
RY/BY, OE
112
113
124
125
141
142
145
144
143
157
156
155
135
98
99
102
103
104
105
106
107
108
109
110
111
72
71
27
53
59
23
24
25
4
3
XECS
XEWC
XEBSY
CS1
CS4
HRD
HWRH
HWRL
WAIT
HINT1
HINT3
RST
CPUCK
MUTE
MD2
NORF
DFCT
FWON
LOCK
ARPRST
ARPINT
ARPWT
ARPWR
ARPRD
ARPCS
AVDWT
AVDRST
57RST
VS
MCK
HA 0-5, 17-19
HA 0-5, 17-19
IC601
HGA
HD 8-15
126-133146-154
HD 0-7
NFD 0-7
XIFINT
FCSON
SDPRST
SDPIT
SDPWR
SDPRD
SDPCS
SPDLSTOP
SPGAIN
XDRVMUTE
LDMM/DMM
OCSW1
CKSW1
CKSW2
TSW1
DSW1
TRMS
TRMP
CKMM
CKMP
01IT0
01IT1
01CS
XDACS2
XDACS3
01RST
DACRST
MA MUTE
12
ı
19
5
ı
11
56
22
54
114
115
116
117
118
57
94
93
91
64
88
83
67
68
69
70
89
90
29
30
28
96
97
31
26
49
FD 0-7
TEST, CLE, ALE,
XWE, XWP,
XCE, XRE, R/B
IC602
16M NAND-F
18
ı
21
I/O 0-7
24
ı
27
2
ı
5
40
ı
43
FCSON
XSDPRST
XSDPIT
XSDPWR
XSDPRD
XSDPCS
SPDLSTOP
SPGAIN
XDRVMUTE
LDMM/DMM
OCSW1
CKSW1
CKSW2
TSW1
DSW1
TRMM
TRMP
CKMM
CKMP
X01INT0
X01INT1
X01CS
XDACS2
XDACS3
X01RST
XDACRST
MA MUTE
SC1
SO1
SI1
CS0L
SC0
SO0
SI0
XFRRST
RF, SERVO
(SEE PAGE 3-4)
AUDIO 1
(SEE PAGE 3-9)
AUDIO 2
(SEE PAGE 3-11)
IC203
BUFFER
12
4A
4Y
2A
2Y
4 6
1A
1Y
1 3
SC1
AUDIO 1
SO1
(SEE PAGE 3-7)
SI1
11
XVIFCS
IFSC0
IFSO0
IFSI0
XFRRST
XIFINT
INTERFACE
CONTROL
(SEE PAGE 3-14)
3-7 3-8
Page 32
3-5. AUDIO (1) BLOCK DIAGRAM
MB-85 BOARD(4/6)
(SEE PAGE 4-33,35)
DVP-C650D/C653D
SIGNAL PROCESS,
VIDEO
(SEE PAGE 3-6)
SYSTEM CONTROL
(SEE PAGE 3-7,8)
BCK
LRCK
ACH12
ACH34
ACH56
CDDOUT
CDDATA
CDBCK
CDLRCK
X01INT0
X01INT1
X01CS
SI1
SO1
SC1
XDACS0
XDACS1
XDACS2
XDACS3
X01RST
XDACRST
SO1
SC1
CS0
CS1
CS2
CS3
SO1
SC1
IC501
AUDIO DSP
47 9
BCKI
49 10
LRCKI
52 11
CH12I
51 15
CH34I
50 14
CH56I
25
CDDOBYP
26
CDSOBYP
27
CDBKCKI
28
CDLRCKI
55
CPU INT0
56
CPU INT1
61
SI
62
CS
63
SO
66
SCK
CLK
ACKI
RST
33 7 68
DO
BCKO
LRCKO
CH78O
CH12O
CH34O
CH56O
16
3
1
SO1
SC1
12
CH12O
CH34O
CS0
SO1
SC1
CS1
SO1
SC1
CS2
2
26
27
28
3
1
2
26
27
28
3
1
2
26
27
28
AUDIO 2CH DAC
BCLKIN
LRCIN
D IN
MD
MC
ML
FRONT L/R DAC
BCLKIN
LRCIN
D IN
MD
MC
ML
REAR L/R DAC
BCLKIN
LRCIN
D IN
MD
MC
ML
IC902
RSTB
IC905
RSTB
IC906
RSTB
V OUT L
16
V OUT R
13
21
ZERO
17
ZEROR
XTI
522
V OUT L
16
V OUT R
13
21
ZERO
17
ZEROR
XTI
522
V OUT L
16
V OUT R
13
21
ZERO
17
ZEROR
XTI
522
SPDIF
AUDIOLT
AUDIORT
ZFLT
ZFRT
AUDIOL
AUDIOR
ZFL
ZFR
AUDIOLS
AUDIORS
ZFLS
ZFRS
AUDIO 2
(SEE PAGE 3-11)
384FS01
27M01
384FSDA
CH56O
SO1
SC1
CS3
05
3
1
2
26
27
28
IC907
CENTER/WOOFER DAC
BCLKIN
LRCIN
D IN
MD
MC
ML
RSTB
XTI
522
V OUT L
V OUT R
ZERO
ZEROR
16
13
21
17
AUDIOC
AUDIOLFE
ZFC
ZFLFE
3-9 3-10
Page 33
DVP-C650D/C653D
3-6. AUDIO (2) BLOCK DIAGRAM
MB-85 BOARD(5/6)
(SEE PAGE 4-35)
INTERFACE
CONTROL
(SEE PAGE 3-14)
SYSTEM CONTROL
(SEE PAGE 3-7,8)
A MUTE
MA MUTE
GAIN1
GAIN2
SPDIF
AUDIOLT
AUDIORT
ZFLT
ZFRT
CN005
IC505
1
D IN
CN401
J502
J505
COAXIAL
DIGITAL
OUT
OPTICAL
L
AUDIO OUT1
R
L
AUDIO OUT2
R
HP-114 BOARD
(SEE PAGE 4-58)
HPL
1
HPR
3
CN701
1
3
RV701
LEVEL
J701
PHONES
AU-215 BOARD(2/3)
(SEE PAGE 4-43,45)
AUDIO IN
SPDIF
15
AUDIOLT
11
AUDIORT
13
ZFLT
10
ZFRT
19
A MUTE
9
MA MUTE
7
GAIN1
17
CN301
14
IC431
LPF +6dB
18
16
19
10
20
22
12
3 1
5
Q301
Q305
Q314, 315
LEVEL SHIFT
Q431,432
GAIN
7
CONTROL
Q435, 436
MUTE
L
R
J304
Q323, 324
MUTE
RY301
2
4
9
7
Q316
RELAY DRIVE
3
8
1
IC401
HEAD PHONE AMP
3
5
1
7
Q341
BUFFER
Q401, 402
MUTE
AUDIO 1
(SEE PAGE 3-10)
AUDIOL
AUDIOR
ZFL
ZFR
AUDIOLS
AUDIORS
ZFLS
ZFRS
AUDIOC
AUDIOLFE
21
23
20
27
13
1
3
5
2
7
9
AUDIOL
AUDIOR
ZFL
ZFR
GAIN2
AUDIOLS
AUDIORS
ZFLS
ZFRS
AUDIOC
AUDIOLFE
IC502
LPF +6dB
8
6
9
2
13
11
9
12
1
7
5
3 1
5
Q306
Q307
IC541
LPF +12dB
3 1
5
Q311
Q308
IC571
LPF +12dB, +16dB
3 1
5
Q503, 504
7
7
7
MUTE
Q543, 544
MUTE
Q573, 574
MUTE
RY302
2
4
9
7
Q318
RELAY DRIVE
3
8
1
Q320
Q319, 403, 404
MUTE CONTROL
J508
L
R
L
R
CENTER
WOOFER
FRONT
REAR
5.1CH OUTPUT
ZFC
CN007
6
ZFLFE
12
ZFC
ZFLFE
05
8
2
CN302
Q310
Q309
Q303, 304
MUTE CONTROL
3-11 3-12
Page 34
3-7. INTERFACE CONTROL BLOCK DIAGRAM
DVP-C650D/C653D
FR-154 BOARD
(SEE PAGE 4-55)
D001
(ON/STANDBY)
S004
1
IC001
REMOTE
COMMANDER
RECEIVER
S003
2
DISC SELECT
OUT
S002
3
1
Q002
LED DRIVE
Q001
LED DRIVE
S001
CN001
5
3
2
7
4
IR
LPOWER
LSTBY
BT22
BT11
FL-104 BOARD
(SEE PAGE 4-51,53)
CN204
5
3
2
7
4
IC203
S-LINK
STATUS INCONTROL
SIRCS IN
4
IC202
POWER-ON RESET
V OUT
S223 S222
4
DISC SELECT
5
AU-215 BOARD(3/3)
19
23
70
71
72
76
78
77
8
11
12
14
15
(SEE PAGE 4-43,45)
Q206
X201
4MHz
IC205
FL DRIVER
Q317
BUFFER
J305
MEGA
CONTROL
J501
S-LINK
611
4
7
9
75
20
10
4
5
STATUS<N>
IR
L POWER
L STBY
RESET <N>
AN2
AN1
IC201
IF CON
IC201!¢
3.9Vp-p(4MHz)
A1OUT
A1IN
SCLK1
SOUT1
SIN1
SBUSY1
SRDY1
P CHECK<N>
FRRST <N>
V MUTE
A MUTE <N>
X IN
X OUT
CN301
CN202
A1IN
4
A1OUT
3
SLINK
13
SLINK
8
A1OUT
6
A1IN
7
SC0
12
SI0
14
SO0
13
XIFCS
15
XIFBUSY
16
+3.3V
315
XFRRST
17
V MUTE
10
A MUTE
9
25
26
16
10
12
11
MB-85 BOARD(6/6)
(SEE PAGE 4-29,35)
CN005
CN006
6
4
5
3
2
+3.3V
1
8
9
ND201
VACUUM
FLUORECENT
DISPLAY
+5V
IFSC0
IFSI0
IFSO0
XVIFCS
XIFINT
XFRRST
V MUTE
A MUTE
SYSTEM CONTROL
(SEE PAGE 3-8)
SIGNAL PROCESS, VIDEO
(SEE PAGE 3-5)
AUDIO 2
(SEE PAGE 3-11)
JOG UNIT
ENTER
05
CN203
1
JOG CCW, JOG CW
2
LEFT, RIGHT,
4
UP, DOWN, ENTER
6
I
9
SW-321 BOARD
(SEE PAGE 4-51)
S217
S216
PREV
NEXT
RIGHT
S208
S209
MEGA
CONTROL
S106
1/ALL DISCS SHUFFLE PGM REPEAT CLEAR
INPUTLOAD TIME/
JOG
S107
S108 S109 S110
S102S101S111 S103 S104 S105
TITLE DVD
TEXT
MENU
EX-CHANGE
UP
RETURN
S215
ENTER
S214
DISC
SKIP
DOWN
S213
CN101
LEFT
1
2
S212
OPEN/CLOSE
S202 S201
BT3
BT4
CN205
1
2
17
18
6
3
2
JOG CCW,
JOG CW
AN0
AN3
AN4
EXP CLK
EXP RST<N>
EXP OVF
FLD0-35
L JOG
L MEGA
L MULTI
27
1
80
29
ı
64
65
66
67
2
CLK
4
RESET<N>
7
OVF OUT
Q203
LED DRIVE
Q204
LED DRIVE
Q205
LED DRIVE
9
ı
DIG0-14
23
8 58
DIG15
SEG1-36
D213
JOG
CONTROL
D214
MEGA
DIG1-15
Q211
BUFFER
43
ı
DIG1-15
57
DIG16
5
ı
SEG1-36
40
CK-88 BOARD
(SEE PAGE 4-51)
CN201
XMULTI XMULTI
7 7
LE-24 BOARD
(SEE PAGE 4-14)
D850
DOLBY
DIGITAL
CN903CN902
CN850
CK-81 BOARD
(SEE PAGE 4-61)
2
SE-91 BOARD
(SEE PAGE 4-14)
XMULTI
1
CN656CN657
32
CN802CN803
51
3-13 3-14
Page 35
DVP-C650D/C653D
3-8. POWER BLOCK DIAGRAM
HS-034SF BOARD
(SEE PAGE 4-65)
HS-034SU BOARD
(SEE PAGE 4-67)
CN101
F101
1
2
FR-154 BOARD
(SEE PAGE 4-55)
IC051
05
US, Canadian
L101
LINE
FILTER
L101, 102
LINE
FILTER
E, PX
CN001
EVER5V
66
D101
CN204
Q101-103
SWITCH
FL-104 BOARD
(SEE PAGE 4-51,53)
IC205
IC201
PCONT
T101
PC101
PHOTO
COUPLER
ND201
Q207
–30V REG
IC202
IC203
+12V
+5V
+3.3V
–12V
D211
D311
D611
D511
Q201, 202
T201
DC-DC
CONVERTER
D213, 214
Q211
SWITCH
Q311
SWITCH
Q611
SWITCH
Q511, 512
SWITCH
+3.3V
CN201
CN202
PC103, Q131
POWER
CONTROL
–12V
5
+5V
3 3
EVER5V
2
PCONT
1
3
P211
P312
P311
P611
P511
CK-88 BOARD
(SEE PAGE 4-51)
5
2
1
CN901CN902
CN201
CN202
CN203
AU-215 BOARD
(SEE PAGE 4-43,45)
+12V
4
EVER5V
7
+5V
2
+3.3V
1
–12V
6
M+12V
2
A+12V
1
+5V
5
6
+3.3V
7
EVER5V
2
+5V
3
–12V
5
PCONT
1
+5V
+3.3V
–12V
5
A+12V
+5V
3
EVER5V
2
PCONT
1
M+12V
+12V
–12V
+5V
EVER5V
+3.3V
MB-85 BOARD
(SEE PAGE 4-19 to 37)
CN001
+5V
5
+3.3V
6
7
V3.3V
A+12V
1
S12V
2
CN006 CN009
4
6
2
7
1
15 21
+3.3V
CN304
+5V
S+12V
IC301
+9V REG
IC302
–9V REG
IC303
IC321
IC505
EVER5V
+3.3V
IC404
+3.3 REG
IC904
A+5V REG
IC801
IC802
A+5V
CK-81 BOARD
(SEE PAGE 4-59)
CN651
12
13
IC401
IC651
IC652
IC902
IC905
IC906
IC907
IC401
IC431
IC502
IC541
IC571
CN656
TK-53 BOARD
(SEE PAGE 4-11)
CN002
18
+3.3V
910
CN803
IC203
IC702
IC803
+5V
2
IC302
+3.3 REG
+3.3 REG
+5V
7
IC005
SE-91 BOARD
(SEE PAGE 4-14)
CN802
1
IC303
PH801
PH802
IC001
IC003
IC004
LE-24 BOARD
(SEE PAGE 4-14)
CN850
2
IC201
IC202
IC204
IC205
IC207
IC304
IC402
IC403
IC501
IC502
IC601
IC602
IC701
D850
+5V
1
CN003
IC001
CN001
14
VCC (5V)
OPTICAL
DEVICE
3-15 3-16 E
Page 36
DVP-C650D/C653D
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary mote is printed
in each block.)
For printed wiring boards:
• X : indicates a lead wire mounted on the component
side.
• x : indicates a lead wire mounted on the printed side.
• ® : Through hole.
• b : Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
Caution:
Pattern face side: Pa rts on the pattern face side seen from
(Side B) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Side A) the parts face are indicated.
For schematic Diagram:
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor,
because it is damaged by the heat.
• All resistors are in ohms, 1/
less otherwise specified.
kΩ : 1000 Ω, MΩ : 1000 kΩ.
• All capacitors are in µF unless otherwise noted. pF : µµF
50V or less are not indicated except for electrolytics and
tantalums.
• All variable and adjustable resistors have characteristic curve
B, unless otherwise noted.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
• ¢ : internal component.
• C : adjustment for repair .
• U : B+ Line.
• V : B– Line.
• Circled numbers refer to waveforms.
• Voltages are dc between measurement point.
• Readings are taken with a color-bar signals on DVD reference disc and when playing CD reference disc.
• Readings are taken with a digital multimeter (DC 10 MΩ).
• Voltage variations may be noted due to normal production
tolerances.
Note:
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part
number specified.
4
W (Chip resistors : 1/
Note:
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro
spécifié.
10
W) un-
When indicating parts by reference
number, please include the board
name.
4-1
Page 37
DVP-C650D/C653D
4-1. FRAME SCHEMATIC DIAGRAM
FRAME (1) SCHEMATIC DIAGRAM
FRAME (1/2)
4-3 4-4
Page 38
FRAME (2) SCHEMATIC DIAGRAM
DVP-C650D/C653D
4-5 4-6
FRAME (2/2)
Page 39
DVP-C650D/C653D
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
TK-53 BOARD (SIDE A)
CN001 B-3
CN002 A-3
CN003 C-2
CN004 C-1
D003 B-3
IC001 B-2
Q001 B-4
Q002 B-1
TK-53 (RF/SERVO) PRINTED WIRING BOARD
– Ref. No.: TK-53 board; 3,000 series –
There are few cases that the part isn't mounted in this model is printed on this diagram.
MB-85
(SIGNAL PROCESS/SERVO)
LM-59
(LOADING MOTOR)
FR-154
(IR/POWER SWITCH)
HP-114
(HEADPHONE)
SW-321
(FUNCTION SWITCH)
TK-53
(RF/SERVO)
LE-24
(LED)
AU-215
(AUDIO/VIDEO BUFFER)
SE-91
(SENSOR)
POWER BLOCK
HS-034SU: US, Canadian
HS-034SF: E, PX
(SWITCHING REGULATOR)
CK-88
(CONNECTION)
CK-81
(DRIVE)
FL-104
(FUNCTION SWITCH/IF CON)
RF/SERVO
TK-53
4-7
4-8
Page 40
• Waveforms
DVP-C650D/C653D
1 IC001 1 (DVD play)
200 mV/DIV 100 ns/DIV
536 mVp-p
2 IC001 1 (CD play)
500 mV/DIV 500 ns/DIV
880 mVp-p
3 IC001 @ª (DVD play)
200 mV/DIV 500 ms/DIV
6 IC001 #ª (CD play)
500 mV/DIV 200 ms/DIV
1.7 Vp-p
7 IC001 $º (DVD play)
100 mV/DIV 50 ms/DIV
180 mVp-p
8 IC001 $º (CD play)
500 mV/DIV 50 ms/DIV
592 mVp-p
4 IC001 @ª (CD play)
200 mV/DIV 20 ms/DIV
448 mVp-p
5 IC001 #ª (DVD play)
500 mV/DIV 50 ms/DIV
1.3 Vp-p
860 mVp-p
9 IC001 %¢ (DVD play)
500 mV/DIV 100 ns/DIV
1.5 Vp-p
!º IC001 %¢ (CD play)
500 mV/DIV 500 ns/DIV
1.5 Vp-p
4-9 4-10
RF/SER VO
TK-53
Page 41
DVP-C650D/C653D
TK-53 (RF/SERVO) SCHEMATIC DIAGRAM • See page 4-7 for printed wiring board and page 4-10 for waveforms.
– Ref. No.: TK-53 board; 3,000 series –
RF/SERVO
TK-53
Note:
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro
spécifié.
4-11 4-12
Page 42
SE-91 (SENSOR), LE-24 (LED) PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAM
– Ref. No.: SE-91 board and LE-24 board; 2,000 series –
There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D
MB-85
(SIGNAL PROCESS/SERVO)
TK-53
(RF/SERVO)
LM-59
(LOADING MOTOR)
FR-154
(IR/POWER SWITCH)
HP-114
(HEADPHONE)
SW-321
(FUNCTION SWITCH)
LE-24
(LED)
AU-215
(AUDIO/VIDEO BUFFER)
SE-91
(SENSOR)
POWER BLOCK
HS-034SU: US, Canadian
HS-034SF: E, PX
(SWITCHING REGULATOR)
CK-88
(CONNECTION)
CK-81
(DRIVE)
FL-104
(FUNCTION SWITCH/IF CON)
4-13 4-14
SENSOR, LED
SE-91, LE-24
Page 43
DVP-C650D/C653D
MB-85 BOARD (SIDE A)
CN001 D-2
CN002 D-4
CN003 D-5
CN004 C-1
CN005 B-1
CN006 C-6
CN007 C-1
CN009 A-2
CN010 B-6
CN012 D-6
D801 C-6
D802 C-6
D803 C-6
D804 C-6
D805 C-5
D807 C-5
IC001 A-2
IC003 A-3
IC004 B-3
IC202 A-5
IC205 B-6
IC302 D-3
IC303 C-4
IC401 C-2
IC501 A-2
IC601 A-4
IC701 C-5
IC904 A-1
Q801 C-5
Q802 C-6
Q803 C-6
MB-85 (SIGNAL PROCESS) PRINTED WIRING BOARD
– Ref. No.: MB-85 board; 1,000 series –
There are few cases that the part isn't mounted in this model is printed on this diagram.
MB-85
(SIGNAL PROCESS/SERVO)
TK-53
(RF/SERVO)
LM-59
(LOADING MOTOR)
FR-154
(IR/POWER SWITCH)
HP-114
(HEADPHONE)
SW-321
(FUNCTION SWITCH)
LE-24
(LED)
SIGNAL PROCESS
MB-85
AU-215
(AUDIO/VIDEO BUFFER)
SE-91
(SENSOR)
POWER BLOCK
HS-034SU: US, Canadian
HS-034SF: E, PX
(SWITCHING REGULATOR)
CK-88
(CONNECTION)
CK-81
(DRIVE)
FL-104
(FUNCTION SWITCH/IF CON)
4-15 4-16
Page 44
MB-85 BOARD (SIDE B)
D701 C-2
D806 C-2
IC005 A-6
IC201 A-3
IC203 A-3
IC204 B-2
IC207 A-2
IC304 C-3
IC402 C-5
IC403 C-5
IC404 D-5
IC502 C-6
IC602 A-4
IC702 B-1
IC801 C-2
IC802 C-1
IC803 C-1
IC902 A-6
IC905 B-6
IC906 B-6
IC907 C-6
DVP-C650D/C653D
4-17 4-18
SIGNAL PROCESS
MB-85
Page 45
DVP-C650D/C653D
MB-85 (AV DECODER) SCHEMATIC DIAGRAM • See page 4-15 for printed wiring board.
– Ref. No.: MB-85 board; 1,000 series –
AV DECODER
MB-85 (1/10)
4-19 4-20
Page 46
MB-85 (SDRAM) SCHEMATIC DIAGRAM • See page 4-15 for printed wiring board.
– Ref. No.: MB-85 board; 1,000 series –
DVP-C650D/C653D
• Wavef orms
1 IC401 %¢
720 mVp-p (H)
2 IC401 %¶
728 mVp-p (H)
3 IC401 %•
5 IC401 ^™
816 mVp-p (H)
6 IC401 ^∞
1.2 Vp-p (H)
4 IC401 ^¡
1.0 Vp-p (H)
1.1 Vp-p (H)
4-21 4-22
SDRAM
MB-85 (2/10)
Page 47
DVP-C650D/C653D
• Waveforms
1 IC701 ^ª (DVD play)
500 mV/DIV 50 ms/DIV
1.4 Vp-p
2 IC701 ^ª (CD play)
500 mV/DIV 200 mV/DIV
MB-85 (SERVO DSP) SCHEMATIC DIAGRAM • See page 4-15 for printed wiring board.
– Ref. No.: MB-85 board; 1,000 series –
1.7 Vp-p
3 IC701 ^• (DVD play)
100 mV/DIV 5 ms/DIV
180 mVp-p
4 IC701 ^• (CD play)
500 mV/DIV 50 ms/DIV
860 mVp-p
SERVO DSP
MB-85 (3/10)
4-23 4-24
Page 48
MB-85 (DRIVE) SCHEMATIC DIAGRAM • See page 4-15 for printed wiring board.
– Ref. No.: MB-85 board; 1,000 series –
DVP-C650D/C653D
4-25 4-26
DRIVE
MB-85 (4/10)
Page 49
DVP-C650D/C653D
MB-85 (ARP) SCHEMATIC DIAGRAM • See page 4-15 for printed wiring board.
– Ref. No.: MB-85 board; 1,000 series –
• Wavef orms
1 IC303 !¶ (DVD play)
500 mV/DIV 100 ns/DIV
1.6 Vp-p
2 IC303 !ª (CD play)
500 mV/DIV 200 ns/DIV
1.6 Vp-p
ARP
MB-85 (5/10)
4-27 4-28
Page 50
MB-85 (SYSTEM CONTROL) SCHEMATIC DIAGRAM • See page 4-15 for printed wiring board.
– Ref. No.: MB-85 board; 1,000 series –
DVP-C650D/C653D
• Wavef orms
1 IC202 (™
4-29 4-30
2.4 Vp-p (12.5 MHz)
2 IC202 5
4 Vp-p (25.3 MHz)
SYSTEM CONTROL
MB-85 (6/10)
Page 51
DVP-C650D/C653D
MB-85 (HGA) SCHEMATIC DIAGRAM • See page 4-15 for printed wiring board.
– Ref. No.: MB-85 board; 1,000 series –
HGA
MB-85 (7/10)
4-31 4-32
Page 52
MB-85 (CLOCK GENERATOR/AUDIO DSP/V EQ/NR) SCHEMATIC DIAGRAM • See page 4-15 for printed wiring board and page 4-38 for waveforms.
– Ref. No.: MB-85 board; 1,000 series –
DVP-C650D/C653D
4-33
4-34
CLOCK GENERATOR/AUDIO DSP/V EQ/NR
MB-85 (8/10)
Page 53
DVP-C650D/C653D
MB-85 (DAC) SCHEMATIC DIAGRAM • See page 4-15 for printed wiring board.
– Ref. No.: MB-85 board; 1,000 series –
DAC
MB-85 (9/10)
4-35 4-36
Page 54
MB-85 (BIAS) SCHEMATIC DIAGRAM • See page 4-15 for printed wiring board.
– Ref. No.: MB-85 board; 1,000 series –
DVP-C650D/C653D
• Waveforms
:E, PX
:US, Canadian
1 IC004 2, 5, 7
4.2 Vp-p (26.9 MHz)
2 IC003 5, 7
DVD: 6.2 Vp-p (37.0 MHz)
CD :5 Vp-p (33.6 MHz)
3 IC001 6
6 IC001 !¢ (DVD play)
4.2 Vp-p (25.3 MHz)
7 IC001 !¢ (CD play)
4.7 Vp-p (22.5 MHz)
4.2 Vp-p (27.0 MHz)
4 IC001 !™
4.6 Vp-p (33.8 MHz)
5 IC001 !¶
DVD: 5.8 Vp-p (36.5 MHz)
CD :5.1 Vp-p (33.8 MHz)
4-37 4-38
BIAS
MB-85 (10/10)
Page 55
DVP-C650D/C653D
AU-215 (AUDIO/VIDEO BUFFER) PRINTED WIRING BOARD
– Ref. No.: AU-215 board; 2,000 series –
There are few cases that the part isn't mounted in this model is printed on this diagram.
MB-85
(SIGNAL PROCESS/SERVO)
LM-59
(LOADING MOTOR)
FR-154
(IR/POWER SWITCH)
HP-114
(HEADPHONE)
SW-321
(FUNCTION SWITCH)
AUDIO/VIDEO BUFFER
AU-215
AU-215
TK-53
(RF/SERVO)
LE-24
(LED)
(AUDIO/VIDEO BUFFER)
SE-91
(SENSOR)
POWER BLOCK
HS-034SU: US, Canadian
HS-034SF: E, PX
(SWITCHING REGULATOR)
CK-88
(CONNECTION)
CK-81
(DRIVE)
FL-104
(FUNCTION SWITCH/IF CON)
4-39 4-40
Page 56
DVP-C650D/C653D
AU-215 BOARD (SIDE B)
CN301 C-8
CN302 C-7
CN303 C-7
CN304 C-11
CN401 C-1
D301 C-11
D303 B-11
D304 A-3
D305 A-3
D306 B-4
D307 B-3
D308 C-8
D309 A-8
D310 A-11
D311 A-9
D312 B-7
D401 B-4
D402 C-4
D431 C-4
D525 B-10
D551 C-7
D561 A-11
D591 C-6
IC301 B-11
IC302 C-11
IC303 B-2
IC321 B-3
IC401 C-3
IC431 B-5
IC502 B-8
IC505 A-10
IC541 B-7
IC571 B-6
Q301 C-5
Q303 C-11
Q304 C-8
Q305 C-5
Q306 C-9
Q307 C-9
Q308 C-6
Q309 C-5
Q310 C-6
Q311 C-8
Q314 C-8
Q315 C-7
Q316 B-8
Q317 A-11
Q318 B-9
Q319 B-7
Q320 B-7
Q321 B-3
Q322 B-3
Q323 A-9
Q324 A-8
Q341 A-10
Q401 B-3
Q402 C-4
Q403 A-7
Q404 B-4
Q431 C-5
Q432 A-5
Q435 B-4
Q436 C-4
Q503 B-10
Q504 B-10
Q543 A-6
Q544 C-6
Q573 B-5
Q574 C-5
4-41 4-42
AUDIO/VIDEO BUFFER
AU-215
Page 57
DVP-C650D/C653D
AU-215 (AUDIO) SCHEMATIC DIAGRAM • See page 4-39 for printed wiring board.
– Ref. No.: AU-215 board; 2,000 series –
AUDIO
AU-215 (1/2)
4-43 4-44
Page 58
AU-215 (VIDEO BUFFER) SCHEMATIC DIAGRAM • See page 4-39 for printed wiring board.
– Ref. No.: AU-215 board; 2,000 series –
DVP-C650D/C653D
• Wavef orms
1 IC321 2
2 IC321 4
3 IC321 7
1.1 Vp-p (H)
1.2 Vp-p (H)
5 IC321 !£
2.4 Vp-p (H)
6 IC321 !∞
2.0 Vp-p (H)
860 mVp-p (H)
4 IC321 !º
1.8 Vp-p (H)
4-45 4-46
VIDEO BUFFER
AU-215 (2/2)
Page 59
DVP-C650D/C653D
FL-104 (FUNCTION SWITCH/IF CON), SW-321 (FUNCTION SWITCH) AND CK-88 (CONNECTION) PRINTED WIRING BOARDS
– Ref. No.: FL-104 board, SW-321 board and CK-88 board; 2,000 series –
There are few cases that the part isn't mounted in this model is printed on this diagram.
MB-85
(SIGNAL PROCESS/SERVO)
TK-53
(RF/SERVO)
LM-59
(LOADING MOTOR)
FR-154
(IR/POWER SWITCH)
HP-114
(HEADPHONE)
SW-321
(FUNCTION SWITCH)
LE-24
(LED)
AU-215
(AUDIO/VIDEO BUFFER)
SE-91
(SENSOR)
POWER BLOCK
HS-034SU: US, Canadian
HS-034SF: E, PX
(SWITCHING REGULATOR)
CK-88
(CONNECTION)
CK-81
(DRIVE)
FL-104
(FUNCTION SWITCH/IF CON)
4-47
FUNCTION SWITCH/IF CON, CONNECTION
FL-104, CK-88
4-48
Page 60
FL-104 BOARD
(SIDE B)
CN201 C-9
CN202 C-6
CN203 D-11
CN204 D-1
CN205 A-12
D202 C-3
D205 C-2
D206 D-9
D209 D-9
D213 D-11
D214 C-11
D215 C-8
D216 D-8
IC201 C-5
IC202 C-4
IC203 C-2
IC205 C-3
Q201 C-9
Q202 C-9
Q203 D-11
Q204 C-11
Q205 C-10
Q206 C-6
Q207 C-8
Q211 C-2
DVP-C650D/C653D
4-49
4-50
FUNCTION SWITCH/IF CON, FUNCTION SWITCH
FL-104, SW-321
Page 61
DVP-C650D/C653D
FL-104 (FUNCTION SWITCH), SW-321 (FUNCTION SWITCH) AND CK-88 (CONNECTION) SCHEMATIC DIAGRAM • See page 4-47 for printed wiring boards.
– Ref. No.: FL-104 board, SW-321 board and CK-88 board; 2,000 series –
HS-034SF BOARD
(SEE PAGE 4-66)
HS-034SU BOARD
(SEE PAGE 4-70)
CN203
:E,PX
CN203
:US, Canadian
4-51
FUNCTION SWITCH, CONNECTION
FL-104 (1/2), SW-321, CK-88
4-52
Page 62
FL-104 (IF CON) SCHEMATIC DIAGRAM • See page 4-47 for printed wiring board.
– Ref. No.: FL-104 board; 2,000 series –
DVP-C650D/C653D
4-53 4-54
• Wavef orm
1 IC201 !¢
3.9 Vp-p (4 MHz)
IF CON
FL-104 (2/2)
Page 63
DVP-C650D/C653D
FR-154 (IR/POWER SWITCH) PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAM
– Ref. No.: FR-154 board; 2,000 series –
There are few cases that the part isn't mounted in this model is printed on this diagram.
IR/POWER SWITCH
FR-114
4-55 4-56
Page 64
HP-114 (HEADPHONE) PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAM
– Ref. No.: HP-114 board; 2,000 series –
There are few cases that the part isn't mounted in this model is printed on this diagram.
DVP-C650D/C653D
MB-85
(SIGNAL PROCESS/SERVO)
LM-59
(LOADING MOTOR)
FR-154
(IR/POWER SWITCH)
HP-114
(HEADPHONE)
SW-321
(FUNCTION SWITCH)
TK-53
(RF/SERVO)
LE-24
(LED)
AU-215
(AUDIO/VIDEO BUFFER)
SE-91
(SENSOR)
POWER BLOCK
HS-034SU: US, Canadian
HS-034SF: E, PX
(SWITCHING REGULATOR)
CK-88
(CONNECTION)
CK-81
(DRIVE)
FL-104
(FUNCTION SWITCH/IF CON)
4-57 4-58
HEDAPHONE
HP-114
Page 65
DVP-C650D/C653D
LM-59 (LOADING MOTOR), CK-81 (DRIVE) PRINTED WIRING BOARDS
– Ref. No.: CK-81 board; 2,000 series –
There are few cases that the part isn't mounted in this model is printed on this diagram.
MB-85
(SIGNAL PROCESS/SERVO)
LM-59
(LOADING MOTOR)
FR-154
(IR/POWER SWITCH)
HP-114
(HEADPHONE)
SW-321
(FUNCTION SWITCH)
TK-53
(RF/SERVO)
LE-24
(LED)
AU-215
(AUDIO/VIDEO BUFFER)
SE-91
(SENSOR)
POWER BLOCK
HS-034SU: US, Canadian
HS-034SF: E, PX
(SWITCHING REGULATOR)
CK-88
(CONNECTION)
CK-81
(DRIVE)
FL-104
(FUNCTION SWITCH/IF CON)
CK-81 BOARD
(SIDE B)
CN651 A-1
CN656 A-1
CN657 B-1
D651 B-2
D652 B-2
IC651 B-2
IC652 C-2
Q651 B-1
Q652 B-1
Q653 B-1
Q654 B-1
Q656 A-1
LOADING MOTOR, DRIVE
LM-59, CK-81
4-59 4-60
Page 66
LM-59 (LOADING MOTOR), CK-81 (DRIVE) SCHEMATIC DIAGRAM
– Ref. No.: CK-81 board; 2,000 series –
DVP-C650D/C653D
• Wavef orm
1 IC651 !º
11.6 Vp-p (H)
4-61 4-62
LOADING MOTOR, DRIVE
LM-59, CK-81
Page 67
DVP-C650D/C653D
HS-034SF (SWITCHING REGULATOR) PRINTED WIRING BOARD
– Ref. No.: HS-034SF board; 6,000 series –
– E, PX –
There are few cases that the part isn't mounted in this model is printed on this diagram.
MB-85
(SIGNAL PROCESS/SERVO)
LM-59
(LOADING MOTOR)
FR-154
(IR/POWER SWITCH)
TK-53
(RF/SERVO)
AU-215
(AUDIO/VIDEO BUFFER)
SE-91
(SENSOR)
POWER BLOCK
HS-034SU: US, Canadian
HS-034SF: E, PX
(SWITCHING REGULATOR)
HS-034SF BOARD
CN101 A-1
CN201 A-3
CN202 A-3
CN203 A-2
D101 B-1
D102 B-2
D104 B-2
D105 B-2
D106 A-2
D109 A-2
D211 A-3
D311 B-3
D312 A-3
D511 B-2
D611 B-2
D612 B-2
D613 B-3
IC301 B-3
Q101 B-2
Q102 B-2
Q103 B-2
Q211 A-3
Q311 A-3
Q312 A-3
Q511 A-2
Q512 A-3
Q611 B-3
HS-034SF
NL
A
B
05
CN101
AC110-240V
L101
C102
L102
C103
J101
BOARD
J214
D
R512
D612
C301
R312
1
EB
Q312
Q511
G
J202
J203
C512
L511
C511
D611
J204
R
K
R306
IC301
1
R305
L211
R304
C104
FG101
C101
C110
D101
F101
R104
J102
T2AL 250V
R101
C117
C114
D106
D102
D109
C107
PRIMARY SECONDARY
C112
L150
C113
C152
R120
G
D
S
R151
G
R106
D
S
J103
R116
C116
R110
Q102
C115
R115
E
B
CN203
6
R317
C315
P511
S
T101
811
5
Q103
3
2
PC101
D511
R303
18
R301
Q101
R112
D104
R114
R113
D105
1 2 3
J208
R511
C212
J213
D211
C211
C611
R212
G
J212
D
C311
D311
CN202
J207
C213
7
S
Q211
R211
R311
R612
J215
P211
J206
D312
J205
8
D613
C612
J211
B
Q611
P611
G
J209
R213
E
L311
J210
P312
D
R611
C613
L611
R514
P311
C313
1
R314
S
CN201
B
E
Q311
R513
Q512
LP201
LP202
1-468-372-
FG201
21
HP-114
(HEADPHONE)
SW-321
(FUNCTION SWITCH)
SWITCHING REGULATOR
HS-034SF
CK-88
(CONNECTION)
CK-81
(DRIVE)
LE-24
(LED)
FL-104
(FUNCTION SWITCH/IF CON)
4-63 4-64
Page 68
HS-034SF (SWITCHING REGULATOR) SCHEMATIC DIAGRAM
– Ref. No.: HS-034SF board; 6,000 series –
– E, PX –
12345678910
HS-034SF BOARD
A
B
C
C110
330µF
400V
C112
0.022µF
400V
C113
47pF
2KV
165.1
R104
3.3M
1/2W
+
Q101
2SK2333
SWITCH
254
165.1
2SK2333
R115
15K
D1N60
Q103
SWITCH
D109
164.6
C114
+
1µF
400V
C152
0.01µF
Q102
2SC3377
SWITCH
D106
D1N60
50V
R151
15K
R120
R106
100K
100K
1/2W
1/2W
2.9
C117
0.0033µF
50V
D102
RD18FB2
L150
45
C116
0.01µF
50V
2.9
D104
RD2.4ESB2
0.2
R113
680
C115
0.033µF
50V
R112
R116
220
2W
2.7K
R110
3.3K
T101
DVP-C650D/C653D
!
D211
F5KF20
D311
31DQ04
D611
31DQ04
B+
C211
+
560µF
35V
B+
B+
C611
330µF
++
35V
D612
RD18FB2
+
C311
560µF
35V
C212
560µF
35V
CN201 8P
L211
10µH
2.4A
C213
+
47µF
35V
L311
10µH
2.4A
C613
47µF
35V
3.4
R611
10K
C313
+
1000µF
25V
L611
10µH
2.4A
+
+
C612
330µF
35V
R612
1/2W
27
Q611
2SA1679
3.3V REG
R211
10K
2.6
3.3
D613
1SS270A
Q312
2SC1740S
POWER
CONTROL
12
P611
R212
!
12
Q211
2SJ490
12V REG
6
10K
5.1
R314
60V
10K
2A
0.7
R311
100
1/2W
D312
1SS270A
0.1
0.8
R317
10K
5
Q311
2SJ488
5V REG
750mA
C315
10µF
50V
P312
60V
R511
!
P211
60V
500mA
!
P311
+
10K
R514
!
60V
2A
39K
4.9
4.9
R513
10K
4.3
2SA933S
–12V SWITCH
R312
1K
Q512
B+
B+
R213
10
2W
B+
B+
B+
1
2
3
4
5
6
7
8
CN202 7P
7
6
5
4
3
2
1
CN203 6P
1
2
3
4
5
6
+3.3V
+5V
GND
+12V
GND
–12V
E+5V
GND
+3.3V
+3.3V
+5V
GND
GND
M+12V
A+12V
P-CONT
E+5V
+5V
GND
–12V
GND
AU-215 BOARD
CN304
(SEE PAGE 4-43)
MB-85 BOARD
CN001
(SEE PAGE 4-37)
CK-88 BOARD
CN901
(SEE PAGE 4-51)
D
E
F
R114
1.2K
D105
!
CN101
!
AC IN
05
!
2P
F101
1
250V
!
2A
C101
0.1µF
2
250V
L101
18mH
0.5A
!
C102
0.1µF
250V
!
C103
100pF
250V
L102
18mH
0.5A
!
C104
100pF
250V
R101
1/2W
1M
D101
S1WBA60
!
C107
1000pF
250V
1SS270A
!
TLP721F
IC301
SHUNT REG
PC101
IC301
AN1431T
D511
S2L20U
R303
1K
3.9
2.5
C511
+
1000µF
25V
B–
R301
68
C301
+
1µF
50V
L511
10µH
2.4A
R304
R305
R306
C512
+
47µF
35V
R512
1.5K
47
1.5K
–3.6
!
P511
10K
–12.2
Q511
2SK2279
–12V REG
–12.2
60V
750mA
NO MARK : E-E MODE
B–
Note:
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part
number specified.
4-65 4-66
Note:
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro
spécifié.
SWITCHING REGULATOR
HS-034SF
Page 69
DVP-C650D/C653D
FG101
J102
C102
C103
C104
C116
J103
Q101 Q103
R106
R115
C115
R113
R303
R301
C301
R306
R305
R304
D311
LP202
D511
D612
D611
IC301
D104
D105
R114
R112
R110
CN101
AC120V
2A 125V
C107
C108
CN203 CN202
CN201
FG201
R513
LP201
Q512
P311
R212
R511
D211
J203
J202
P312
P611
EB
J214 J213 J211
J212 J210
J208 J215
J207
Q211
R512
J209
R514P211
R213
R312
R317
C315
Q312
Q511
P511
C112
T101L150
C113
C152
C117
F101
C110
R104
Q102
R116
PC101
J204
C311
J205
L311
C313
C612C611
C511
L511
C512
C212
C211
L611
C613
R611
Q611
D613
R612
R311
D312
J206
R211
C213
L211
Q311
R314
R151
D101
J101
D109
D106
C114
C101
L101
611 78 1
EB
S
S
S
G
G
G
D
D
D
SECONDARYPRIMARY
NL
B
KR
E
G
S
D
G
S
D
11
18
8
5
3
2
1 2 3
A
B
05
1-468-372-
11
HS-034SU
BOARD
B
E
HS-034SU (SWITCHING REGULATOR) PRINTED WIRING BOARD
– Ref. No.: HS-034SU board; 6,000 series –
– US, Canadian –
HS-034SU BOARD
CN101 A-1
CN201 A-3
CN202 A-3
CN203 A-2
D101 B-1
D104 B-2
D105 B-2
D106 A-2
D109 A-2
D211 A-3
D311 B-3
D312 A-3
D511 B-2
D611 B-2
D612 B-2
D613 B-3
IC301 B-3
Q101 B-2
Q102 B-2
Q103 B-2
Q211 A-3
Q311 A-3
Q312 A-3
Q511 A-2
Q512 A-3
Q611 B-3
There are few cases that the part isn't mounted in this model is printed on this diagram.
MB-85
FR-154
(IR/POWER SWITCH)
HP-114
(HEADPHONE)
(SIGNAL PROCESS/SERVO)
LM-59
(LOADING MOTOR)
SW-321
(FUNCTION SWITCH)
SWITCHING REGULATOR
HS-034SU
TK-53
(RF/SERVO)
LE-24
(LED)
AU-215
(AUDIO/VIDEO BUFFER)
SE-91
(SENSOR)
POWER BLOCK
(SWITCHING REGULATOR)
CK-81
(DRIVE)
FL-104
(FUNCTION SWITCH/IF CON)
HS-034SU: US, Canadian
HS-034SF: E, PX
CK-88
(CONNECTION)
4-67 4-68
Page 70
HS-034SU (SWITCHING REGULATOR) SCHEMATIC DIAGRAM
– Ref. No.: HS-034SU board; 6,000 series –
– US, Canadian –
12345678910
HS-034SU BOARD
A
B
C
C110
270µF
200V
C112
0.022µF
400V
C113
47pF
2KV
165.1
R104
3.3M
1/2W
+
Q101
2SK2185
SWITCH
254
165.1
2SK2185
R115
15K
D1N60
Q103
SWITCH
D109
164.6
C114
+
1µF
400V
C152
0.01µF
Q102
2SC3377
SWITCH
D106
D1N60
50V
R151
15K
R106
180K
1/2W
2.9
C117
0.0033µF
50V
L150
45
C116
0.01µF
50V
2.9
D104
RD2.4ESB2
0.2
R113
680
C115
0.033µF
50V
R112
R116
220
1/2W
2.7K
R110
3.3K
T101
DVP-C650D/C653D
!
D211
F5KF20
D311
31DQ04
D611
31DQ04
B+
C211
+
560µF
35V
B+
B+
C611
330µF
++
35V
D612
RD18FB2
+
C311
560µF
35V
C212
560µF
35V
CN201 8P
L211
10µH
2.4A
C213
+
47µF
35V
L311
10µH
2.4A
C613
47µF
35V
3.4
R611
10K
C313
+
1000µF
25V
L611
10µH
2.4A
+
+
C612
330µF
35V
R612
1/2W
27
Q611
2SA1679
3.3V REG
R211
10K
2.6
3.3
D613
1SS270A
Q312
2SC1740S
POWER
CONTROL
12
P611
R212
!
12
Q211
2SJ490
12V REG
6
10K
5.1
R314
60V
10K
2A
0.7
R311
100
1/2W
D312
1SS270A
0.1
0.8
R317
10K
5
Q311
2SJ488
5V REG
750mA
C315
10µF
50V
P312
60V
R511
!
P211
60V
500mA
!
P311
+
10K
R514
!
60V
2A
39K
4.9
4.9
R513
10K
4.3
2SA933S
–12V SWITCH
R312
1K
Q512
B+
B+
R213
10
2W
B+
B+
B+
1
2
3
4
5
6
7
8
CN202 7P
7
6
5
4
3
2
1
CN203 6P
1
2
3
4
5
6
+3.3V
+5V
GND
+12V
GND
–12V
E+5V
GND
+3.3V
+3.3V
+5V
GND
GND
M+12V
A+12V
P-CONT
E+5V
+5V
GND
–12V
GND
AU-215 BOARD
CN304
(SEE PAGE 4-43)
MB-85 BOARD
CN001
(SEE PAGE 4-37)
CK-88 BOARD
CN901
(SEE PAGE 4-51)
D
E
F
R114
1.2K
D105
!
CN101
!
AC IN
05
!
2P
F101
1
125V
!
2A
2
C101
0.1µF
250V
L101
18mH
0.5A
!
C102
0.1µF
250V
!
C103
470pF
250V
!
C104
470pF
250V
D101
S1WBA60
!!
C107
470pF
250V
C108
470pF
250V
1SS270A
!
TLP721F
IC301
SHUNT REG
PC101
IC301
AN1431T
D511
S2L20U
R303
1K
3.9
2.5
C511
+
1000µF
25V
B–
R301
68
C301
+
1µF
50V
L511
10µH
2.4A
R304
R305
R306
C512
+
47µF
35V
R512
1.5K
47
1.5K
–3.6
!
P511
10K
–12.2
Q511
2SK2279
–12V REG
–12.2
60V
750mA
NO MARK : E-E MODE
B–
Note:
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque ! sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro
spécifié.
4-69 4-70 E
SWITCHING REGULATOR
HS-034SU
Page 71
Pin No. Pin name I/O Function
68 EOP0 I Not used
69 AVCC - Power supply
70 AVRH - Reference power supply (+3.3V)
71 AGND - Ground
72 AN0 I Set of mode 0
73 AN1 I Set of mode 1
74 AN2 I Set of mode 2
75 AN3 I Set of mode 3 (fixed at “H”)
76 SI0 I Serial data input from IF CON and EEPROM
77 SO0 O Serial data output to IF CON and EEPROM
78 SC0 O Serial clock output to IF CON and EEPROM
79 SI1 I Serial bus 1 (for data input)
80 SO1 O Serial bus 1 (for data output)
81 SI2 I Serial bus 2 (for data input)
82 SO2 O Serial bus 2 (for data output)
83 PF7 O Reset signal output
84 DACK1 O Output of DMA-ACK 0 to AV DEC
85 DACK0 O Output of DMA-ACK 1 to AV DEC
86 DREQ1 I Input of DMA-REQ 0 from AV DEC
87 DREQ0 I Input of DMA-REQ 1 from AV DEC
88 INT3 I Input of interrupt from HGA
89 SC1 O Serial clock output
90 GND - Ground
91 X1 O Clock output (12.5MHz)
92 X0 I Clock input (12.5MHz)
93 VCC5 - Power supply
94 INT1 I Input of interrupt ARP and SERVO DSP
95 INT0 I Input of interrupt from AV DEC
96 PB0 I Rear panel lime input select (“H”: DISC “L”: EXT)
97 PB1 O Chip select signal to IF CON
98 PB2 O Chip select signal to DAC (Lt and Rt)
99 PB3 O Chip select signal to DAC (L and R)
100 PB4 O DVD/CD select (“H”: 44.1kHz “L”: 48kHz)
5-1. SYSTEM CONTROL PIN FUNCTION (MB-85 BOARD IC202)
Pin No. Pin name I/O Function
1 PB5 O Analog filter gain control
2 PB6 O VES gain control “H”: VES
3 PB7 O Rear CH boost control “H”: rear boost
4 VCC3 - Power supply
5 CLK O CPU clock out (25 MHz)
6 CS5 O Not used
7 CS4 O Chip select signal for ARP, SERVO DSP and HGA
8 CS3 O Chip select signal for SDRAM and AV DEC
9 CS2 O Chip select signal for REG and AV DEC
10 CS1 O Chip select signal for external SRAM
11 CS0 O Chip select signal for external FLASH ROM
12 NMI I Not used (fixed at “H”)
13 HST I Not used (fixed at “H”)
14 RST I Reset signal input from IF CON
15 GND - Ground
16 MD0 I Input of mode select 0 (fixed at “1”)
17 MD1 I Input of mode select 1 (fixed at “0”)
18 MD2 I Input of mode select 2 (fixed at “0”)
19 RDY I Wait signal input
20 P81 I Test terminal (fixed at “H”)
21 P82 I Test terminal (fixed at “L”)
22 RD O Read enable signal output
23 WR0 O High byte write enable signal output (16 bit and 8 bit)
24 WR1 O Low byte write enable signal output (16 bit only)
25-32 D16-D23 I/O Data bus D0-D7 (16 bit)
33-39 D24-D30 I/O Data bus D8-D14 (16 bit), D0-D6 (8 bit)
40 GND - Ground
41 D31 I/O Data bus D15 (16 bit), D7 (8 bit)
42 A00 O Address bus A0
43 VCC5 - Power supply
44-64 A01-A21 O Address bus A1-A21
65 GND - Ground
66 P66 O PLL IC control output “H”: DOUBLE
67 P67 I DIAG mode signal input “L”: DIAG
5-1 E
IC PIN FUNCTION DESCRIPTION
SECTION 5
DVP-C650D/C653D
Page 72
SECTION 6
TEST MODE
DVP-C650D/C653D
6-1. GENERAL DESCRIPTION
The T est Mode allows you to make diagnosis and adjustment easily using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
6-2. STARTING TEST MODE
Press [TITLE], [CLEAR], [POWER] buttons on the remote commander in this order with the power of main unit in OFF status,
and the T est Mode starts, then the menu shown below will be displayed on the TV screen. At the bottom of menu screen, the model
name and revision number are displayed.
To execute each function, select the desired menu and press its
number on the remote commander.
To exit from the Test Mode, press the POWER button.
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. Mecha Aging
4. Emergency History
5. Version Information
6. Video Level Adjustment
Exit: Power Key
_
Model : DPX12xxxx
Revision : 1.xxxx
6-3. SYSCON DIAGNOSIS
The same contents as board detail check by serial interface can be
checked from the remote commander.
On the T est Mode Menu screen, press [0] k e y on the remote commander, and the following check menu will be displayed.
### Syscon Diagnosis ###
Diag All Check
No. 2 Version
2-3. ROM Check Sum
Check Sum = xxxx
Press NEXT Key to Continue
Press PREV Key to Repeat
_
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press [NEXT] key to go to the next item,
or [PREV] ke y to repeat the same check again. To quit the diagnosis and return to the Check Menu screen, press [STOP] or
[ENTER] key. If an err or occurred, the diagnosis is suspended
and the error code is displayed as shown below.
### Syscon Diagnosis ###
3-3. EEPROM Check
Error 03: EEPROM Write/Reed N
Address : 00000001
Write Data : 2492
Read Data : 2490
Press NEXT Key to Continue
Press PREV Key to Repeat
_
Press [STOP] key to quit the diagnosis, or [PREV] key to repeat
the same item where an error occurred, or [NEXT] key to continue
the check from the item next to faulty item.
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. Version
3. Peripheral
4. Servo
5. Supply
6. AV Decoder
7. Video
8. Audio
_
0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
1. All
All items continuous check
This menu checks all diagnostic items continuously . Normally , all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judgment through a visual check to the result, the following screen is
displayed for the key entry.
Selecting 2 and subsequent items calls the submenu screen of each
item.
For example, if “5. Supply” is selected, the following submenu
will be displayed.
### Syscon Diagnosis ###
Check Menu
No. 5 Supply
0. Quit
1. All
2. ARP Register Check
3. ARP to RAM Data Bus
4. ARP to RAM Address Bus
5. ARP RAM Check
_
0. Quit
Quit the submenu and return to the main menu.
1. All
All submenu items continuous check
This menu checks 2 and subsequent items successively. At the
item where visual check is required for judgment or an error occurred, the checking is suspended and the message is output for
key entry. Nor mally, all items are checked successively one after
another automatically unless an error is found.
6-1
Page 73
Selecting 2 and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see “Check Items List”.
General Description of Checking Method
2. Version
(2-2) Revision
ROM revision number is displayed.
Error: Not detected.
The revision number defined in the source file of ROM
(IC205) is displayed with four digits.
(2-3) ROM Check Sum
Check sum is calculated.
Error: Not detected.
The 8-bit data are added at addresses 0x000F0000 ~
0x002EFFFF of ROM (IC205) and the result is displayed
with 4-digit hexadecimal number. Error is not detected.
Compare the result with the specified value.
(2-4) Model Type
Model code is displayed.
Error: Not detected.
The model code read from EEPROM (IC201) is displayed
with 2-digit hexadecimal number.
Model Type
DVP-C650D (US, Canadian) 6 0
DVP-C650D (E) 6 1
DVP-C653D (PX) 6 0
(2-5) Region
Region code is displayed.
Error: Not detected.
The region code determined from the model code is displayed.
3. Peripheral
(3-2) Gate Array Check
Data write → read, and accord check
Error 02: Gate array write/read discord
Data 0x00~0xFF are written to the address 0xF of GA
(IC601), then read and checked if they accord.
(3-3) EEPROM Check
Data write → read, and accord check
Error 03: EEPROM write/read discord
Data 0x9249, 0x2942, 0x4294 are written to addresses
0x00~0xFF of EEPROM (IC201), then read and checked.
Before writing, the data are saved, then after checking, they
are written to restore the contents of EEPROM.
(3-4) NAND Flash Check
Data clear → write → read, and accord check
Error 04: Clear error
05: Write error
06: Read data discord
21: Faulty blocks exceed 10
The data clear, write, read, and check are executed to the
block 0 of Flash memory (IC602).
In case of a faulty block, its address is displayed.
An error is output if faulty blocks exceed 10.
4. Servo
(4-2) Servo DSP Check
Data write → read, and accord check
Error 12: Read data discord
Data 0x9249, 0x2942, 0x4294 are written to the address
0x602 of RAM in the Servo DSP (IC701), then read and
checked.
(4-3) DSP Driver Test
Test signal data → DSP Driver
Error: Not detected.
Caution: Do not conduct this test with a mechanical deck
connected.
The maximum voltage is applied to the Servo
Driver IC (IC801, IC802). If mechanical deck is
connected, the motor and optics could be damaged. Disconnect mechanical deck following the
output message, then enter specified 4- or 5-digit
number from the remote commander, and press
the [ENTER]. The test is conducted only when
the input data accord. Check the output level, then
press the [NEXT] to finish the test.
This test is skipped if “All” is selected.
Supplement: How to disconnect mechanical deck
Disconnect flat cables connected to the CN002
and CN003 of MB-85 board. Also, disconnect
harness from the CN011.
5. Supply
Caution: Do not conduct this check with a mechanical deck con-
nected.
An access is made to the stream supply and servo control IC (IC303) and external RAM (IC304) using check
data. If mechanical deck is connected, the motor and
optics could be damaged. This check is also executed by
the “All” menu item.
Supplement: How to disconnect mechanical deck
Disconnect flat cables connected to the CN002 and
CN003 of MB-85 board. Also, disconnect harness
from the CN011.
(5-2) ARP Register Check
Data write → read, and accord check
Error 08: ARP register write, and read data discord
Data 0x00 to 0xFF are written to the TMAX register (address 0xC6) in ARP (IC303), then they are r ead and checked.
(5-3) ARP to RAM Data Bus
Data write → read, and accord check
Error 09: ARP ←→ RAM data bus error
Data 0x0001 to 0x8000 where one bit each is set to 1 are
written to the address 0 of RAM (IC304) connected to the
ARP (IC303) through the bus, then they are read and
checked. In case of discord, written bit pattern and read
data are displayed. If data where multiple bits are 1 are
read, the bits concerned may touch each other. Further, if
data where certain bit is always 1 or 0 regardless of written
data, the line could be disconnected or shorted.
6-2
Page 74
(5-4) ARP to RAM Address Bus
Data write → other address read discord check
Error 10: ARP → RAM address bus error
Caution: Address and data display in case of an error is
different from the display of other diagnosis (de-
scribed later).
Before starting the test, all addresses of RAM (IC304) are
cleared to 0x0000.
First, 0xA55A is written to the address 0x00000, and the
address data are read and checked from addresses 0x00001
to 0x80000 while shifting 1 bit each. Next, the data at that
address is cleared, and it is written to the address 0x00001,
and read and checked in the same manner. This check is
repeated up to the address 0x80000 while shifting the address data by 1 bit each.
If data other than 0 is read at the addresses except written
address, an error is given because all addresses were already cleared to 0. In this check, the error display pattern is
different from that of other diagnosis; read data, written
address, and read address are displayed in this order. Ho wever , the message uses same template, and accordingly e xchange Address and Data when reading. The following display, for example,
### Syscon Diagnosis ###
5-4. ARP to RAM Address Bus
Error 10: ARP - RAM Address B
Address : 0000A55A
Write Data : 00000000
Read Data : 00080000
Press NEXT Key to Continue
Press PREV Key to Repeat
_
6. AV Decoder
(6-2) 1930 RAM
Data write → read, and accord check
Error 13: AVD RAM read data discord
The program code data stored in ROM (IC205) are copied
to all areas of RAM (IC402, IC403) connected to the AVD
(IC401) through the bus, then they are read and checked if
they accord. Further, the same test is conducted once again
with the data where all bits are inverted between 1 and 0. If
discord is detected, faulty address, written data, and read
data are displayed following the error code 13, and the test
is suspended.
(6-3) 1930 SP
ROM → AVD RAM → Video OUT
Error: Not detected.
The data including sub picture streams in ROM (IC205)
are transferred to the RAM (IC402, IC403) in AVD (IC401),
and output as video signals from the AVD (IC401).
They are output from all video terminals (Composite, Y/C,
Component) except EURO AV terminal.
7. Video
(7-2) Color Bar
AVD color bar command write → Video OUT
Error: Not detected.
The command is transferred to the AVD, and the color bar
signals are output from video terminals.
They are output from all video terminals (Composite, Y/C,
Component) except EURO AV terminal.
8. Audio
(8-2) ARP → 1930
Error 14: ARP → 1930 video NG
15: ARP → 1930 audio NG
shows the data 0xA55A was read from address 0x00080000
though it was written to the address 0x00000000. This implies that these addresses are in the form of shadow. Also,
if the read data is not 0xA55A, another error will be present.
(5-5) ARP RAM Check
Data write → read, and accord check
Error 11: ARP RAM read data discord
The program code data stored in ROM are copied to all
areas of RAM (IC304) connected to the ARP (IC303)
through the bus, then they are read and checked if they accord. If the detail check was selected initially, the data are
written to all areas and read, then the same test is conducted
once again with the data where all bits are inverted between
1 and 0. If discord is detected, faulty address, written data,
and read data are displayed following the error code 11,
and the test is suspended.
(8-3) Test Tone
A pink noise signal is output from the AVD (IC401) through
optical coaxial digital terminal and analog audio terminal.
Error: Not detected.
All channels → 2ch Left → 2ch Right → Front Left →
Front Right → Rear Left → Rear Right → Center → Sub
Woofer are checked in this order.
Note: Sub Woofer is checked only for low-frequency com-
ponents, and no sound will be heard unless a proper
super woofer is connected.
6-3
Page 75
Check Items List
2) Version
(2-2) Revision
(2-3) ROM Check Sum
(2-4) Model Type
(2-5) Region
3) Peripheral
(3-2) Gate Array Check
(3-3) EEPROM Check
(3-4) NAND Flash Check
4) Servo
(4-2) Servo DSP Check
(4-3) DSP Driver Test
5) Supply
(5-2) ARP Register Check
(5-3) ARP to RAM Data Bus
(5-4) ARP to RAM Address Bus
(5-5) ARP RAM Check
6) AV Decoder
(6-2) 1930 RAM
(6-3) 1930 SP
Error Codes List
00: Error not detected
01: RAM write/read data discord
02: Gate array NG
03: EEPROM NG
04: Flash memory clear error
05: Flash memory write error
06: Flash memory read data discord
08: ARP register read data discord
09: ARP ←→ RAM data bus error
10: ARP ←→ RAM address bus error
11: ARP RAM read data discord
12: Servo DSP NG
13: 1930 SDRAM NG
14: ARP → 1930 video NG
15: ARP → 1930 audio NG
16: 1910 UCODE download NG
17: System call error (function not supported)
18: System call error (parameter error)
19: System call error (illegal ID number)
20: System call error (time out)
21: NAND Flash faulty blocks exceed 10
90: Error occurred
91: User verification NG
92: Diagnosis cancelled
7) Video
(7-2) Color Bar
8) Audio
(8-2) ARP → 1930
(8-3) Test Tone
6-4
Page 76
6-4. DRIVE AUTO ADJUSTMENT
On the T est Mode Menu screen, press [1] k e y on the remote commander, and the drive auto adjustment menu will be displayed.
1. DVD-SL (single layer)
Select [1], insert DVD single layer disc, and press [ENTER] key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM.
## Drive Auto Adjustment ##
Adjustment Menu
0. ALL
1. DVD-SL
2. CD
3. DVD-DL
4. SACD
Exit: RETURN
Normally, [0] is selected to adjust DVD (single layer), CD, DVD
(dual layer), and SACD in this order. But, individual items can be
adjusted for the case where adjustment is suspended due to an
error. In this mode, the adjustment can be made easily through the
operation following the message displayed on the screen.
The disc used for adjustment must be the one specified for adjustment. However, for SACD disc, use the player with initial data if
the disc is not available.
0. ALL
Select [0], insert each disc (1. DVD-SL, 2. CD, 3. DVD-SL, 4.
SACD) to table from No.1 to No. 4 and press [ENTER] key, and
the servo set data in EEPROM will be initialized. Then, 1. DVDSL disc, 2. CD disc, 3. DVD-DL disc, and 4. SACD disc are adjusted in this order. Though the message to confirm whether discs
other than SACD disc are adjusted is not displayed, you can finish
the adjustment if pressing the
of each disc, the measurement for disc type judgment is made. As
automatic adjustment does not judge the disc type unlike conv entional models, take care not to insert wrong type discs. Also, do
not give a shock during adjustment.
[STOP] button. During adjustment
DVD Single Layer Disc Adjustment Steps
1. SLED TIL T Reset
2. Disc Check Memory SL
3. Wait 300 msec
4. Set Disc Type SL
5. LD ON
6. Spdl Start
7. Wait 1 sec
8. Focus Servo ON 0
9. Auto Track Offset Adjust
10. CLVA ON
11. Wait 500 msec
12. Tracking ON
13. Wait 1 sec
14. Sled ON
15. Check CLV Lock
16. Auto LFO Adjust
17. Auto Focus Offset Adjust
18. Auto Tilt Position Adjust
19. Auto Focus Gain Adjust
20. Auto Focus Offset Adjust
21. EQ Boost Adjust
22. Auto LFO Adjust
23. Auto Track Gain Adjust
Search Check
24. 32Tj Fwd
25. 32Tj Rev
26. 500Tj Fwd
27. 500Tj Rev
28. All Servo Stop
29. Eep Copy Loop Filter Offset
6-5
Page 77
2. CD
Select [2], insert CD disc, and press [ENTER] key, and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM.
3. DVD-DL (dual layer)
Select [3], insert DVD dual layer disc, and press [ENTER] key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM.
CD Adjustment Steps
1. Sled Tilt Rest
2. Disc Check Memory CD
3. Wait 500 msec
4. Set Disc Type CD
5. LD ON
6. Spdl Start
7. Wait 500 msec
8. Focus Servo ON 0
9. Auto Track Offset Adjust
10. CLVA ON
11. Wait 500 msec
12. Tracking ON
13. (TC Display Start)
14. Wait 1 sec
15. Jitter Display Start
16. Sled ON
17. Check CLV ON
18. Auto LFO Adjust
19. Auto Focus Offset Adjust
20.
21. Auto Focus Gain Adjust
22. Auto Focus Offset Adjust
23. Eq Boost Adjust
24. Auto LFO Adjust
25. Auto Track Gain Adjust
Search Check
26. 32Tj Fwd
27. 32Tj Rev
28. 500Tj Fwd
29. 500Tj Rev
30. All Servo Stop
DVD Dual Layer Disc Adjustment Steps
1. Sled Tilt Reset
2. Disc Check Memory DL
3. Wait 500 msec
4. Set Disc Type DL
5. LD ON
6. Spdl Start
7. Wait 1 sec
Layer 1 Adjust
8. Focus Servo ON 0
9. Auto Track Offset Adjust
10. Clva ON
11. Wait 500 msec
12. Tracking ON
13. Wait 500 msec
14. Sled ON
15. Check CLV Lock
16. Auto Loop Filter Offset Auto Focus Adjust
17.
18. Auto Focus Gain Adjust
19. Auto Focus Offset Adjust
20. Eq Boost Adjust
21. Auto Loop Filter Offset
22. Auto Track Gain Adjust
Search Check
23. 32Tj Fwd
24. 32Tj Rev
25. 500Tj Fwd
26. 500Tj Rev
Layer 0 Adjust
27. Fj (L1 -> L0)
28. Auto Track Offset Adjust L0
29. Clva ON
30. Wait 500 msec
31. Tracking ON
32. Wait 500 msec
33. Sled ON
34. Check CLV Lock
35. Auto Focus Filter Offset
36. Auto Focus Adjust
37.
38. Auto Focus Gain Adjust
39. Auto Focus Offset Adjust
40. Eq Boost Adjust
41. Auto Loop Filter Offset
42. Auto Track Gain Adjust
Search Check
43. 32Tj Fwd
44. 32Tj Rev
45. 500Tj fwd
46. 500Tj Rev
Layer Jump Check
47. Lj (L0 -> L1)
48. Lj (L1 -> L0)
49. All Servo Stop
6-6
Page 78
4. SACD
Select [4], insert SACD disc, and press [ENTER] key, and the
adjustment will be made through the following steps, then adjusted
values will be written to the EEPROM. However, if SACD disc is
not available, use the player with initial data, skipping the SACD
adjustment. In this case, you can finish the adjustment if pressing
the [STOP] button.
6-5. DRIVE MANUAL OPERATION
On the T est Mode Menu screen, select [2], and the manual operation menu will be displayed. For the manual operation, each servo
on/off control and adjustment can be executed manually.
## Drive Manual Operation ##
SACD Adjustment Steps
1. Sled Tilt Reset
2. Set Disc Type CD
3. LD ON
4. Spdl Start
5. Wait 500 msec
6. Focus Servo ON 0
7. Auto track Offset Adjust
8.
9. CL VA ON
10. Wait 500 msec
11. Tracking ON
12. Wait 1 sec
13. Sled ON
14. Check CLV ON
15. Auto Focus Offset Adjust
17.
18. Auto Focus Gain Adjust
19. Auto Focus Offset Adjust
20. Eq Boost Adjust
21. Auto LFO Adjust
22. Auto Track Gain Adjust
23. 32Tj Fwd
24. 32Tj Rev
25. 500Tj Fwd
26. 500Tj Rev
27. All Servo Stop */
1. Disc type
Operation Menu
2. Servo Control
3. Track/Layer Jump
4. Manual Adjustment
5. Auto Adjustment
6. Memory Check
0. Disc Check Memory
Exit: Return
In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is displayed when a disc is loaded.
1. Set correctly the disc type to be used on the Disc Type
screen.
The disc type must be set after a disc was loaded.
The set disc type is cleared when the tray is opened.
2. After power ON, if the Drive Manual Operation was selected, first perform “Reset SLED TILT” by opening 1.
Disc Type screen.
3. In case of an alarm, immediately press the [STOP] button to stop the servo operation, and turn the power OFF.
Basic operation (controllable from front panel or remote commander)
[POWER] Power OFF
[STOP] Servo stop
[OPEN/CLOSE] Stop+Eject/Loading
[RETURN] Return to Operation Menu or Test Mode
Menu
[NEXT], [PREV] Transition between sub modes of menu
[1] to [9], [0] Selection of menu items
Cursor UP/DOWN Increase/Decrease in manually adjusted
value
6-7
Page 79
0. Disc Check Memory
Disc Check
1. SL Disc Check
2. CD Disc Check
3. DL Disc Check
0. Reset SLED TILT
1. Disc Type Auto Check
Disc Type
2. DVD SL 12 cm
3. DVD DL 12 cm
4. CD 12cm
5. SACD 12 cm
6. DVD SL 8 cm
7. DVD DL 8 cm
8. CD 8 cm
9. SACD 8 cm
0. Reset SLED TILT
TC. : : EMG. 00
CD 12 cm
Display when CD 12cm disc was selected
On this screen, the mirror time is measured to judge the disc and it
is written to the EEPROM. First load DVD SL disc and press [1],
next load CD disc and press [2], and finally load DVD DL disc
and press [3].
The adjustment must be executed more than once after default
data were written. External vibration or shock to the player must
not be given. Reference value for DVD is from 10 to 20, and for
CD, from 28 to 4F.
Check that the value of CD is larger than that of DVD.
When those values are beyond a range perform this adjustment
again.
From this screen, you can go to another mode by pressing [NEXT]
or [PREV] key , but you cannot enter this mode from another mode.
You can enter this mode from the Operation Menu screen only.
1. Disc T ype
Disc Type
1. Disc Type Auto Check
2. DVD SL 12 cm
3. DVD DL 12 cm
4. CD 12cm
5. SACD 12 cm
6. DVD SL 8 cm
7. DVD DL 8 cm
8. CD 8 cm
9. SACD 8 cm
0. Reset SLED TILT
EMG. 00
[0] Reset SLED TILT Reset the Sled and Tilt to initial posi-
tion.
[1] Disk Type Check Judge automatically the loaded disc. As
the judged result is displayed at the bottom of screen, make sure that it is correct.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
[2] to [9] Select the loaded disc. The adjusted
value is written to the address of selected disc. No further entry is necessary if [1] was selected.
2. Servo Control
Servo Control
1. LD Off R.Sled FWD
2. SP Off L.Sled REV
3. Focus Off
4. TRK. Off
5. Sled Off
6. CLVA Off
7. FCS. Srch Off
On this screen, select the disc type. To select the disc type, press
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting [1] automatically selects and displays the
disc type. In case of wrong display, retry “Disc Check Memory”.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
Disc Type
1. Disc Type Auto Check
2. DVD SL 12 cm
3. DVD DL 12 cm
4. CD 12cm
5. SACD 12 cm
6. DVD SL 8 cm
7. DVD DL 8 cm
8. CD 8 cm
9. SACD 8 cm
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
Display when DVD SL 12cm disc was selected
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLV A is turned on, the usual trace mode becomes acti ve . In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLV A.
6-8
Page 80
[0] Reset SLED TILT Reset the Sled and Tilt to initial posi-
tion.
[1] LD Turn ON/OFF the laser.
[2] SP Turn ON/OFF the spindle.
6-6. MECHA AGING
### Mecha Aging ###
[3] Focus Search the focus and turn on the focus.
[4] TRK Turn ON/OFF the tracking servo.
[5] Sled Turn ON/OFF the sled servo.
[6] CLVA Turn ON/OFF normal servo of spindle
servo.
[7] FCS. Srch Apply same voltage as that of focus
search to the focus drive to check the
focus drive system.
→ Sled FWD Move the sled outward. Perform this
operation with the tracking servo turned
off.
← Sled REV Move the sled inward. Perform this op-
eration with the tracking servo turned
off.
↑ Tilt UP Move the tilt upward.
↓ Tilt DOWN Move the tilt downward.
The following menus are normally not used.
3. Track/Layer Jump
Press OPEN key
Abort: STOP key
On the Test Mode Menu screen, selecting [3] executes the aging
of mechanism. First, open the tray and load a disc. Press the [PLAY]
key , and the aging will start. When the tray is closed, the disc type
and size are judged and displayed. During aging, the repeat cycle
is displayed. Aging can be aborted at any time by pressing the
[STOP] key. After the operation has stopped, unload the disc and
press again the [STOP] key or the [RETURN] ke y to return to the
Test Mode Menu.
6-7. EMERGENCY HISTORY
### MEG. History ###
Laser Hours CD xxxxxxxh
DVD xxxxxxxh
1. 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
2. 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
4. Manual Adjustment
5. Auto Adjustment
The persons who do not know well about these menus should not
use them.
6. Memory Check
EEPROM DATA
CD – DVD –
ID No. 00 SACD SL L0 L1
Focus Gain xx xx xx xx xx
TRK. Gain xx xx xx xx xx
Focus Offset xx xx xx xx xx
TRK. Offset xx xx xx xx xx
L. F. Offset xx xx xx xx xx
EQ Boost xx xx xx xx xx
Jitter xx xx xx xx xx
Mirror Time xx xx xx xx xx
_
CLEAR: Default Set
This screen displays current servo adjusted data stored in the
EEPROM. Though adjusted data can be initialized with the
[CLEAR] key, they cannot be restored after initialization.
So, before clearing, make a note of the adjusted data.
For reference, the drive has been designed so that the gain center
value is 20 and offset value is 80. Other values will be in a range
of 10 to 80. If extreme value such as 00 or FF is set, adjustment
will be faulty. In such a case, check for disc scratch or cable disconnection, then perform adjustment again.
Select: 1 – 9 Scroll: UP/DOWN
(1: Last EMG.) Exit: Return
On the Test Mode Menu screen, selecting [4] displays the information such as servo emergency history. The history information
from last 1 up to 10 can be scrolled with ↑key or↓key . Also,
specific information can be displayed by directly entering that
number with ten keys.
The upper two lines display the laser ON total hours. Data below
minutes are omitted.
Clearing History Information
Clearing laser hours
Press [DISPLAY] and [CLEAR] keys in this order.
Both CD and DVD data are cleared.
Clearing emergency history
Press [TITLE] and [CLEAR] keys in this order.
Initializing set up data
Press [DVDMENU] and [CLEAR] keys in this order.
The data have been initialized when “Set Up Initialized” message is displayed. The EMG. History screen will be restored
soon.
6-9
Page 81
How to see Emergency History
31.12
6-8. VERSION INFORMATION
## Version Information ##
2
1 : Emergency Code
2 : Don’t Care
These codes are used for verification of software designing.
3 : Historical order 1 to 9
Emergency Codes List
10: Communication to IC001 (TK-53 board) failed.
11: Each servo for focus, tracking, and spindle is unlocked.
12: Communication to EEPROM, IC201 (MB-85 board) failed.
13: Writing of hours meter data to EEPROM, IC201 (MB-85
board) failed.
14: Communication to Servo DSP IC701 (MB-85 board) failed,
or Servo DSP is faulty.
20: Initialization of tilt servo and sled servo failed. They are not
placed in the initial position.
21: Tilt servo operation error
22: Syscon made a request to move the tilt servo to wrong posi-
tion.
23: Sled servo operation error
24: Syscon made a request to move the sled servo to wrong posi-
tion.
30: Tracking balance adjustment error
31: Tracking gain adjustment error
32: Focus balance adjustment error
33: Focus bias adjustment error
34: Focus gain adjustment error
35: Tilt servo adjustment error
36: RF equalizer adjustment error
37: RF group delay adjustment error
38: Jitter value after adaptive servo operation is too large.
40: Focus servo does not operate.
41: With a dual layer (DL) disc, focus jump failed.50: CLV
(spindle) servo does not operate.
51: Spindle does not stop.
60: With a DVD disc, Syscon made a request to seek nonexistent
address.
61: With a CD disc, Syscon made a request to seek nonexistent
address.
62: With a CD disc, Syscon made a request to seek nonexistent
track No. and index No.
63: With a DVD disc, seeking of target address failed.
64: With a CD disc, seeking of target address failed.
65: With a CD disc, seeking of target index failed.
70: With a D VD disc, physical information data could not be read.
71: With a CD disc, TOC data could not be read.
80: Disc type judgment failed.
81: As disc type judgment failed, retry was repeated.
82: As disc type judgment failed, a measurement error occurred.
83: Disc type could not be judged within the specified time.
84: Illegal command code was received from Syscon.
85: Illegal command was received from Syscon.
IF con. Ver. x. xxx (xxxx)
Group 00
SYScon. Ver. x. xxx (xxxx)
Model xx
Region 0x
SW1 ??
SW2 ??
Exit: RETURN
On the Test Mode Menu screen, selecting [5] displays the ROM
version and region code.
The parenthesized hexadecimal number in version field is
checksum value of ROM.
6-9. VIDEO LEVEL ADJUSTMENT
On the Test Mode Men u screen, selecting [6] displays color bars
for video level adjustment. During display of color bars, OSD disappears but the menu screen will be restored if pressing any key.
Measurement point : LINE OUT VIDEO
(75 Ω terminating resistance)
Measuring instrument: Oscilloscope
Adjustment device : RV401 on MB-85 board
Specified value :1.0 ± 0.02 Vpp
1.0 ± 0.02 Vp-p
6-10 E
6-10
Page 82
SECTION 7
ELECTRICAL ADJUSTMENTS
DVP-C650D/C653D
In making adjustment, refer to 7-3. Adjustment
Related Parts Arrangement.
Note: During diagnostic check, the characters and color bars can
be seen only with the NTSC monitor. Therefore, for diagnostic check, use the monitor that supports both NTSC and
PAL modes
This section describes procedures and instructions necessary for
adjusting electrical circuits in this set.
Instruments required:
1) Color monitor TV
2) Oscilloscope 1 or 2 phenomena, band width over 100 MHz,
with delay mode
3) Frequency counter (over 8 digits)
4) Digital voltmeter
5) Standard commander
(RMT-D112A)
6) DVD reference disc
HLX-501 (J-6090-071-A) (dual layer)
HLX-503 (J-6090-069-A) (single layer)
HLX-504 (J-6090-088-A) (single layer)
HLX-505 (J-6090-089-A) (dual layer)
7) SACD reference disc
HLXA-509 (J-6090-090-A)
7-1. POWER SUPPLY ADJUSTMENT
1. Power Supply Check
(HS-034SF/034SU BOARD)
Mode E-E
Instrument Digital voltmeter
+5 V Check
Test point CN202 pin 5
Specification 5.0 ± 0.2 Vdc
+3.3 V Check
Test point CN202 pin 7
Specification 3.3 ± 0.2 Vdc
EVER+5 V Check
Test point CN203 pin 2
Specification 5.0 ± 0.2 Vdc
P_CONT Check
Test point CN203 pin 1
Specification 4V – 5 Vdc
A +12 V Check
Test point CN202 pin 1
Specification 9.5 Vdc
–12 V Check
Test point CN203 pin 5
Specification –12.0 ± 1.0 Vdc
M +12 V Check
Test point CN202 pin 2
Specification 12.0 ± 1.0 Vdc
+1.5
–0.5
Checking method:
1) Confirm that each voltage satisfies the specification.
7-1
Page 83
7-2. ADJUSTMENT OF VIDEO SYSTEM
1. Video Level Adjustment (MB-85 BOARD)
<Purpose>
This adjustment is made to satisfy the NTSC standard, and if not
adjusted correctly, the brightness will be too large or small.
3. Checking Component Video Output B-Y
(MB-85 BOARD)
<Purpose>
This checks component video output B-Y. If it is incorrect, correct colors will not be displayed when connected to, for instance,
projector.
Mode Video level adjustment in test mode
Signal Color bars
Test point
LINE OUT (VIDEO) connector
(75 Ω terminated)
Instrument Oscilloscope
Adjusting element RV401
Specification 1.0 ± 0.02 Vp-p
Adjusting method:
1) In the test mode initial menu “6” Video Lev el Adjustment, set
so that color bars are generated.
2) Adjust the RV401 to attain 1.0 ± 0.02 Vp-p.
1.0 ± 0.02 Vp-p
Figure 7-1
2. S-terminal Output Check (MB-85 BOARD)
<Purpose>
Check S-terminal video output. If it is incorrect, pictures will not
be displayed correctly in spite of connection to the TV with a Sterminal cable.
Mode Video level adjustment in test mode
Signal Color bars
Test point
S VIDEO OUT (S-Y) connector
(75 Ω terminated)
Instrument Oscilloscope
Specification 1.0 ± 0.1 Vp-p
Checking method:
1) In the test mode initial menu “6” Video Lev el Adjustment, set
so that color bars are generated.
2) Confirm that the S-Y level is 1.0 ± 0.1 Vp-p.
Mode Video level adjustment in test mode
Signal Color bars
Test point
COMPONENT VIDEO OUT (B-Y)
connector (75 Ω terminated)
Instrument Oscilloscope
Specification 700 ± 70 mVp-p
Checking method:
1) Confirm that the B-Y level is 700 ± 70 mVp-p.
700 ± 70 mVp-p
Figure 7-3
4. Checking Component Video Output R-Y
(MB-85 BOARD)
<Purpose>
This checks component video output R-Y. If it is incorrect, correct colors will not be displayed when connected to, for instance,
projector.
Mode Video level adjustment in test mode
Signal Color bars
Test point
COMPONENT VIDEO OUT (R-Y)
connector (75 Ω terminated)
Instrument Oscilloscope
Specification 700 ± 70 mVp-p
Checking method:
1) Confirm that the R-Y level is 700 ± 70 mVp-p.
Figure 7-2
700 ± 70 mVp-p
1.0 ± 0.1 Vp-p
Figure 7-4
7-2
Page 84
5. Checking Component Video Output Y
12
2728
CN005
RV401
VIDEO LEVEL ADJ
(MB-85 BOARD)
<Purpose>
This checks component video output Y. If it is incorrect, correct
brightness will not be attained when connected to, for instance,
projector.
Mode Video level adjustment in test mode
Signal Color bars
Test point
COMPONENT VIDEO OUT (Y)
connector (75 Ω terminated)
Instrument Oscilloscope
Specification 1.0 ± 0.1 Vp-p
Checking method:
1) Confirm that the Y level is 1.0 ± 0.1 Vp-p.
1.0 ± 0.1 Vp-p
Figure 7-5
7-3. ADJUSTMENT RELATED PARTS ARRANGEMENT
MB-85 BOARD (SIDE A)
6. Checking S Video Output S-C (MB-85 BOARD)
<Purpose>
This checks whether the S-C satisfies the NTSC Standard. If it is
not correct, the colors will be too dark or light.
Mode Video level adjustment in test mode
HS-034SF/034SU BOARD (SIDE A)
Signal Color bars
Test point CN005 pin 5
7116
CN203CN202
Instrument Oscilloscope
Specification 286 ± 50 mVp-p
Connection:
5
4
CN005
Oscilloscope
100µF
+
75Ω
±1%
100k
±1%
Checking method:
1) Confirm that the S-C burst is 286 ± 50 mVp-p.
286 ± 50 mVp-p
Figure 7-6
7-3 7-4 E
Page 85
8-1. EXPLODED VIEWS
DVP-C650D/C653D
SECTION 8
REPAIR PARTS LIST
NOTE:
• -XX and -X mean standardized parts, so they may
have some difference from the original one.
• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
8-1-1. MAIN ASSEMBLY
25
9
10
not supplied
26
9
9
not supplied
5
not
supplied
2
7
6
4
9
8
2
25
not
supplied
9
• The mechanical parts with no reference number in
the exploded views are not supplied.
• Hardware (# mark) list and accessories and packing materials are given in the last of the electrical
parts list.
11
2
14
15
3
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
23
10
10
15
13
10
24
12
15
14
not
supplied
1
22
1 X-3949-804-1 COVER ASSY, TRAY
2 3-970-608-11 SUMITITE (B3), +BV
3 3-988-693-11 SPACER, CARD
* 4 A-6065-334-A MB-85 BOARD, COMPLETE (EXCEPT E)
* 4 A-6065-335-A MB-85 BOARD, COMPLETE (E)
5 3-054-650-01 SPRING, EMC
6 1-791-197-11 CABLE, FLEXIBLE FLAT (FMA-14)
7 1-791-198-11 CABLE, FLEXIBLE FLAT (FMA-15)
8 1-791-199-11 CABLE, FLEXIBLE FLAT (FMA-16)
9 3-055-791-01 SUMITITE (B3) (RING), +BV
2
2
15
17
18
14
16
2
19
20
21
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
14 4-957-280-31 BRACKET (GUIDE B1)
15 3-970-608-51 SUMITITE (B3), +BV
16 3-056-474-01 PANEL, REAR (EXCEPT E)
16 3-056-474-11 PANEL, REAR (E)
* 17 A-6065-325-A AU-215 BOARD, COMPLETE
* 18 A-6065-336-A CK-88 BOARD, COMPLETE
* 19 1-468-372-11 POWER BLOCK (HS-034SU) (US, Canadian)
* 19 1-468-372-21 POWER BLOCK (HS-034SF) (E, PX)
20 3-957-819-01 FOOT
21 3-051-085-01 SPACER (KGLS-RT), ROCKING CARD
10 3-710-901-41 SCREW, TAPPING
* 11 3-051-081-01 CASE, UPPER
! 12 1-782-001-61 CORD, POWER (E, PX)
! 12 1-790-155-11 CORD, POWER (US, Canadian)
13 1-500-386-11 FILTER, CLAMP (FERRITE CORE)
* 22 3-051-059-01 PLATE, BOTTOM
23 1-418-321-41 COMMANDER, STANDARD (RMT-D112A)
24 3-055-539-01 LID, BATTERY CASE (for RMT-D112A)
25 3-531-576-01 RIVET
26 3-051-301-01 SPRING, SHIELD
8-1
Page 86
8-1-2. FRONT PANEL ASSEMBLY
57
61
60
62
59
76
not supplied
77
63
71
54
64
75
54
74
65
not
supplied
54
69
66
78
54
54
70
79
54
54
54
72
73
54
not supplied
67
55
56
51
51 X-3949-294-1 RING ASSY, SHUTTLE
52 X-3949-806-1 DOOR ASSY, CONTROL
* 53 A-6065-328-A SW-321 BOARD, COMPLETE
54 4-951-620-01 SCREW (2.6X8), +BVTP
55 X-3949-805-1 PANEL ASSY, FRONT (EXCEPT PX)
55 X-3949-971-1 PANEL ASSY, FRONT (PX)
56 3-056-545-01 WINDOW, INDICATION
57 3-056-539-01 ESCUTCHEON
58 4-977-598-11 CUSHION
59 3-056-584-01 LATCH, D. C.
68
58
54
53
52
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
65 3-056-542-01 BUTTON, JOG
66 X-3949-816-1 BUTTON ASSY, CONTROL
67 3-056-544-01 BUTTON, PLAY
68 3-051-069-01 UTTON, EJECT
69 3-988-016-01 STICK, CURSOR
70 1-418-097-11 ENCODER, ROTARY (JOG/CURSOR BUTTON)
71 4-045-250-01 DAMPER
* 72 A-6065-326-A FL-104 BOARD, COMPLETE
73 1-791-201-11 CABLE, FLEXIBLE FLAT (FMF-37)
* 74 A-6065-327-A FR-154 BOARD, COMPLETE
60 3-974-997-31 WINDOW, REMOTE CONTROL
61 4-963-404-21 EMBLEM (5-A), SONY
62 3-988-030-51 BUTTON, POWER
63 3-056-540-01 BUTTON, DISK SELECT
64 3-056-541-01 BUTTON, NEXT
* 75 3-684-436-01 PLATE, MOUNT
76 3-974-959-11 KNOB, VOLUME
77 2-118-268-01 NUT (M9), HEXAGON
* 78 A-6065-329-A HP-114 BOARD, COMPLETE
79 3-051-079-04 REINFORCEMENT
8-2
Page 87
8-1-3. TABLE ASSEMBLY
#1
101
115
111
112
114
#3
113
103
110
M951
#2
116
117
109
110
104
105
108
102
106
107
118
119
110
110
120
121
101 A-6062-078-A TABLE (LOADING) ASSY
102 3-051-084-01 TABLE (LOADING)
103 X-4947-960-1 ROLLER ASSY
104 4-957-292-11 SLIDER (RACK)
105 4-957-294-01 SPRING (D.T), TENSION
106 4-957-293-01 SPRING (RACK RELEASE)
107 4-957-291-11 LEVER (RACK RELEASE)
108 4-957-868-01 SCREW (+PTPWH 2.6X20)
109 X-4943-480-1 BRACKET (ROLLER D) ASSY
110 3-970-608-11 SUMITITE (B3), +BV
* 111 4-957-278-01 BEARING (ROTARY A)
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
* 112 X-3948-858-1 GEAR (ROTARY) ASSY
113 3-051-076-01 BELT (RM)
114 X-3948-857-1 BRACKET (RM) ASSY
115 3-056-530-01 TABLE (ROTARY)
116 3-051-063-01 GEAR (DRIVE)
117 3-325-697-01 WASHER
118 1-791-202-11 CABLE, FLEXIBLE FLAT (FCS-4)
* 119 A-6065-331-A SE-91 BOARD, COMPLETE
* 120 A-6065-337-A LE-24 BOARD, COMPLETE
121 3-056-550-01 COVER, LED
M951 A-6062-080-A MOTOR ASSY, ROTARY (TURN TABLE)
8-3
Page 88
8-1-4. CHASSIS ASSEMBLY
154
165
165
166
154
168
154
154
153
156
157
155
164
162
158
163
159
160
154
154
161
167
177
165
178
154
170
175
169
171
172
183
180
183
#1
182
171
172
179
184
172
181
171
173
154
174
M991
152
151
151 4-944-490-01 BELT (TIMING)
152 X-4941-529-1 PULLEY ASSY
* 153 A-6065-332-A LM-59 BOARD, COMPLETE
154 3-970-608-11 SUMITITE (B3), +BV
* 155 4-951-619-01 CUSHION (A)
156 4-962-087-01 SPRING (S), TENSION
157 4-957-285-01 LEVER, SET
158 4-934-375-31 GEAR (LOADING B)
159 4-957-303-01 GEAR (LOADING C)
160 4-957-279-11 LEVER, LOCK
161 4-957-281-01 SPRING (LOCK LEVER)
162 X-4943-478-1 BRACKET (GEAR) ASSY
163 1-466-996-21 ENCODER, ROTARY (LOADING)
164 4-957-288-01 GEAR (MAIN)
165 4-957-283-01 WASHER (5), STOPPER
176
154
not supplied
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number specified.
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
169 3-056-532-01 PULLEY, CHUCKING
170 3-051-082-01 STOPPER (BU)
171 4-981-923-01 SCREW (M), STEP
172 3-053-847-01 INSULATOR
* 173 A-6065-333-A TK-53 BOARD, COMPLETE
174 1-791-195-11 CABLE, FLEXIBLE FLAT (FTM-8)
175 3-056-531-01 HOLDER, BU
* 176 A-6065-330-A CK-81 BOARD, COMPLETE
* 177 4-981-731-01 CUSHION (U/D) L
* 178 4-981-731-11 CUSHION (U/D) R
179 1-791-196-11 CABLE, FLEXIBLE FLAT (FTM-9)
180 1-791-200-11 CABLE, FLEXIBLE FLAT (FMC-13)
! 181 8-820-081-03 OPTICAL PICK-UP KHM-220AAA/J1RP
182 3-531-576-01 RIVET
183 1-543-950-11 CORE, FERRITE
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
166 4-957-287-01 GEAR (REV)
167 4-957-286-11 GEAR (U/D)
168 3-051-074-01 BRACKET (CP)
184 3-056-592-01 HOLDER, FLEXIBLE
M991 A-4604-834-A MOTOR ASSY, LOADING
8-4
Page 89
8-2. ELECTRICAL PARTS LIST
AU-215
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* A-6065-325-A AU-215 BOARD, COMPLETE
**********************
< CAPACITOR >
C302 1-126-926-11 ELECT 1000uF 20% 10V
C303 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C304 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C305 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
C306 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
C307 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
C308 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C309 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C310 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C311 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C312 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
C313 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
C314 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
C315 1-126-935-11 ELECT 470uF 20% 6.3V
C316 1-104-665-11 ELECT 100uF 20% 10V
C317 1-126-935-11 ELECT 470uF 20% 6.3V
C318 1-104-665-11 ELECT 100uF 20% 10V
C319 1-126-935-11 ELECT 470uF 20% 6.3V
C320 1-104-665-11 ELECT 100uF 20% 10V
C321 1-104-665-11 ELECT 100uF 20% 10V
C322 1-104-665-11 ELECT 100uF 20% 10V
C323 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C324 1-126-935-11 ELECT 470uF 20% 6.3V
C325 1-126-935-11 ELECT 470uF 20% 6.3V
C326 1-104-664-11 ELECT 47uF 20% 16V
C327 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C328 1-104-664-11 ELECT 47uF 20% 16V
C329 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C330 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C331 1-163-233-11 CERAMIC CHIP 18PF 5% 50V
C332 1-163-233-11 CERAMIC CHIP 18PF 5% 50V
C334 1-163-233-11 CERAMIC CHIP 18PF 5% 50V
C335 1-163-233-11 CERAMIC CHIP 18PF 5% 50V
C336 1-163-233-11 CERAMIC CHIP 18PF 5% 50V
C338 1-104-664-11 ELECT 47uF 20% 16V
C339 1-104-664-11 ELECT 47uF 20% 16V
C342 1-104-664-11 ELECT 47uF 20% 16V
C343 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. . uPA. . : µPA. .
uPB. . : µPB. . uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
• Not all of the parts for POWER BLOCK (HS034SF/034SU) are listed.
C344 1-126-960-11 ELECT 1uF 20% 50V
C345 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
(Ref.No. 2,000 Series)
C346 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C347 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C348 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C349 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C350 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C351 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C352 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C353 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C401 1-104-665-11 ELECT 100uF 20% 10V
C404 1-104-665-11 ELECT 100uF 20% 10V
C431 1-104-664-11 ELECT 47uF 20% 16V
C432 1-104-664-11 ELECT 47uF 20% 16V
C433 1-104-665-11 ELECT 100uF 20% 10V
C434 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C435 1-104-665-11 ELECT 100uF 20% 10V
C436 1-163-131-00 CERAMIC CHIP 390PF 5% 50V
C437 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C438 1-163-131-00 CERAMIC CHIP 390PF 5% 50V
C439 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C440 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C442 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C443 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C447 1-136-850-11 FILM 0.1uF 5% 63V
C448 1-104-664-11 ELECT 47uF 20% 16V
C449 1-104-664-11 ELECT 47uF 20% 16V
C450 1-136-850-11 FILM 0.1uF 5% 63V
C501 1-104-664-11 ELECT 47uF 20% 16V
C502 1-104-664-11 ELECT 47uF 20% 16V
C503 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C504 1-163-131-00 CERAMIC CHIP 390PF 5% 50V
C505 1-163-131-00 CERAMIC CHIP 390PF 5% 50V
C506 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C507 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C508 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C509 1-136-850-11 FILM 0.1uF 5% 63V
C512 1-136-850-11 FILM 0.1uF 5% 63V
C513 1-104-664-11 ELECT 47uF 20% 16V
C514 1-104-664-11 ELECT 47uF 20% 16V
C521 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C522 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.
8-5
Page 90
AU-215
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C523 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C524 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C525 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C526 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C541 1-104-664-11 ELECT 47uF 20% 16V
C542 1-104-664-11 ELECT 47uF 20% 16V
C543 1-163-130-00 CERAMIC CHIP 360PF 5% 50V
C544 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C545 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C546 1-163-130-00 CERAMIC CHIP 360PF 5% 50V
C547 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C548 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C549 1-104-664-11 ELECT 47uF 20% 16V
C550 1-104-664-11 ELECT 47uF 20% 16V
C571 1-104-664-11 ELECT 47uF 20% 16V
C572 1-104-664-11 ELECT 47uF 20% 16V
C573 1-163-130-00 CERAMIC CHIP 360PF 5% 50V
C574 1-163-020-00 CERAMIC CHIP 0.0082uF 10% 50V
C575 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C576 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V
C577 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C578 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C579 1-104-664-11 ELECT 47uF 20% 16V
C580 1-104-664-11 ELECT 47uF 20% 16V
C581 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
< CONNECTOR >
CN301 1-785-698-11 CONNECTOR, FFC/FPC 28P
CN302 1-785-695-11 CONNECTOR, FFC/FPC 13P
CN303 1-785-694-11 CONNECTOR, FFC/FPC 7P
* CN304 1-568-946-11 PIN, CONNECTOR 8P
* CN401 1-568-941-11 PIN, CONNECTOR 3P
< DIODE >
D301 8-719-988-61 DIODE 1SS355TE-17
D303 8-719-975-40 DIODE RB411D
D304 8-719-067-59 DIODE MAZ9120D0LS0-TX/L
D305 8-719-067-59 DIODE MAZ9120D0LS0-TX/L
D306 8-719-067-59 DIODE MAZ9120D0LS0-TX/L
D307 8-719-067-59 DIODE MAZ9120D0LS0-TX/L
D308 8-719-988-61 DIODE 1SS355TE-17
D309 8-719-988-61 DIODE 1SS355TE-17
D310 8-719-988-61 DIODE 1SS355TE-17
D311 8-719-988-61 DIODE 1SS355TE-17
D312 8-719-988-61 DIODE 1SS355TE-17
D401 8-719-988-61 DIODE 1SS355TE-17
D402 8-719-988-61 DIODE 1SS355TE-17
D431 8-719-914-44 DIODE DAP202K
D525 8-719-914-44 DIODE DAP202K
D551 8-719-914-44 DIODE DAP202K
D561 8-719-067-59 DIODE MAZ9120D0LS0-TX/L
D591 8-719-914-44 DIODE DAP202K
< EARTH TERMINAL >
* ET301 1-537-738-21 TERMINAL, EARTH
* ET302 1-537-738-21 TERMINAL, EARTH
< FERRITE BEAD >
FB305 1-414-553-11 FERRITE 0uH
FB306 1-414-553-11 FERRITE 0uH
FB307 1-414-553-11 FERRITE 0uH
FB308 1-414-553-11 FERRITE 0uH
FB310 1-414-553-11 FERRITE 0uH
FB311 1-414-553-11 FERRITE 0uH
FB312 1-414-553-11 FERRITE 0uH
FB313 1-414-553-11 FERRITE 0uH
FB314 1-414-553-11 FERRITE 0uH
FB315 1-414-553-11 FERRITE 0uH
FB316 1-414-553-11 FERRITE 0uH
FB317 1-414-553-11 FERRITE 0uH
FB318 1-414-553-11 FERRITE 0uH
FB319 1-414-553-11 FERRITE 0uH
FB320 1-414-553-11 FERRITE 0uH
FB321 1-414-553-11 FERRITE 0uH
FB322 1-414-553-11 FERRITE 0uH
FB323 1-414-553-11 FERRITE 0uH
FB324 1-414-553-11 FERRITE 0uH
FB325 1-414-553-11 FERRITE 0uH
FB341 1-414-135-11 FERRITE 0uH
FB342 1-414-553-11 FERRITE 0uH
FB401 1-414-553-11 FERRITE 0uH
FB402 1-414-553-11 FERRITE 0uH
FB403 1-414-553-11 FERRITE 0uH
FB404 1-414-553-11 FERRITE 0uH
FB405 1-414-553-11 FERRITE 0uH
FB406 1-414-553-11 FERRITE 0uH
FB407 1-414-553-11 FERRITE 0uH
FB408 1-414-553-11 FERRITE 0uH
FB409 1-414-553-11 FERRITE 0uH
FB561 1-414-553-11 FERRITE 0uH
FB562 1-414-553-11 FERRITE 0uH
< IC >
IC301 8-759-701-58 IC NJM78M08FA
IC302 8-759-982-54 IC RC79M09FA
IC303 8-759-563-79 IC BA7660F-E2
IC321 8-759-563-79 IC BA7660F-E2
IC401 8-759-909-71 IC BA4558F
IC431 8-759-909-71 IC BA4558F
IC502 8-759-909-71 IC BA4558F
IC505 8-749-016-00 IC HVE0024
IC541 8-759-909-71 IC BA4558F
IC571 8-759-909-71 IC BA4558F
< JACK >
J303 1-793-483-11 JACK, PIN 3P (COMPONENT VIDEO OUT)
J304 1-793-484-11 JACK, PIN 2P (AUDIO IN)
J305 1-764-188-21 JACK (SMALL TYPE) (DIA. 3.5)
(MEGA CONTROL)
J501 1-764-188-21 JACK (SMALL TYPE) (DIA. 3.5) (S-LINK)
J502 1-793-446-21 JACK, PIN 1P (COAXIAL)
J505 1-694-409-41 TERMINAL BOARD (LINE OUT/S VIDEO OUT)
J508 1-793-482-11 JACK, PIN 6P (5.1CH OUTPUT)
< COIL >
L301 1-412-953-11 INDUCTOR 15uH
L302 1-412-953-11 INDUCTOR 15uH
L303 1-412-953-11 INDUCTOR 15uH
L304 1-412-953-11 INDUCTOR 15uH
L305 1-412-953-11 INDUCTOR 15uH
L306 1-412-953-11 INDUCTOR 15uH
8-6
Page 91
AU-215
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
L307 1-412-963-11 INDUCTOR 100uH
L308 1-414-930-21 INDUCTOR 2.2uH
L321 1-412-963-11 INDUCTOR 100uH
R318 1-216-097-91 RES, CHIP 100K 5% 1/10W
R319 1-216-097-91 RES, CHIP 100K 5% 1/10W
R320 1-216-097-91 RES, CHIP 100K 5% 1/10W
< TRANSISTOR >
Q301 8-729-424-08 TRANSISTOR UN2111
Q303 8-729-216-22 TRANSISTOR 2SA1162
Q304 8-729-421-19 TRANSISTOR UN2213
Q305 8-729-424-08 TRANSISTOR UN2111
Q306 8-729-424-08 TRANSISTOR UN2111
Q307 8-729-424-08 TRANSISTOR UN2111
Q308 8-729-424-08 TRANSISTOR UN2111
Q309 8-729-424-08 TRANSISTOR UN2111
Q310 8-729-424-08 TRANSISTOR UN2111
Q311 8-729-424-08 TRANSISTOR UN2111
Q314 8-729-424-08 TRANSISTOR UN2111
Q315 8-729-421-19 TRANSISTOR UN2213
Q316 8-729-422-27 TRANSISTOR 2SD601A-Q
Q317 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q318 8-729-422-27 TRANSISTOR 2SD601A-Q
Q319 8-729-424-08 TRANSISTOR UN2111
Q320 8-729-421-19 TRANSISTOR UN2213
Q321 8-729-421-19 TRANSISTOR UN2213
Q322 8-729-424-08 TRANSISTOR UN2111
Q323 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q324 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q341 8-729-422-27 TRANSISTOR 2SD601A-Q
Q401 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q402 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q403 8-729-424-08 TRANSISTOR UN2111
Q404 8-729-421-19 TRANSISTOR UN2213
Q431 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q432 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q435 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q436 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q503 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q504 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q543 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q544 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q573 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
Q574 8-729-046-97 TRANSISTOR 2SD1938 (F)-T (TX).SO
< RESISTOR >
R321 1-216-073-00 METAL CHIP 10K 5% 1/10W
R322 1-216-073-00 METAL CHIP 10K 5% 1/10W
R323 1-216-021-00 METAL CHIP 68 5% 1/10W
R324 1-216-021-00 METAL CHIP 68 5% 1/10W
R325 1-216-021-00 METAL CHIP 68 5% 1/10W
R326 1-216-021-00 METAL CHIP 68 5% 1/10W
R327 1-216-021-00 METAL CHIP 68 5% 1/10W
R328 1-216-021-00 METAL CHIP 68 5% 1/10W
R329 1-216-049-91 RES, CHIP 1K 5% 1/10W
R330 1-216-073-00 METAL CHIP 10K 5% 1/10W
R333 1-216-049-91 RES, CHIP 1K 5% 1/10W
R334 1-216-097-91 RES, CHIP 100K 5% 1/10W
R335 1-216-049-91 RES, CHIP 1K 5% 1/10W
R336 1-216-089-91 RES, CHIP 47K 5% 1/10W
R337 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R338 1-216-073-00 METAL CHIP 10K 5% 1/10W
R339 1-216-001-00 METAL CHIP 10 5% 1/10W
R340 1-216-089-91 RES, CHIP 47K 5% 1/10W
R341 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R342 1-216-063-91 RES, CHIP 3.9K 5% 1/10W
R343 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R344 1-216-033-00 METAL CHIP 220 5% 1/10W
R345 1-216-021-00 METAL CHIP 68 5% 1/10W
R346 1-216-025-91 RES, CHIP 100 5% 1/10W
R347 1-216-295-91 SHORT 0
R348 1-216-295-91 SHORT 0
R349 1-216-041-00 METAL CHIP 470 5% 1/10W
R350 1-216-041-00 METAL CHIP 470 5% 1/10W
R353 1-216-295-91 SHORT 0
R355 1-216-295-91 SHORT 0
R356 1-216-049-91 RES, CHIP 1K 5% 1/10W
R357 1-216-081-00 METAL CHIP 22K 5% 1/10W
R358 1-216-097-91 RES, CHIP 100K 5% 1/10W
R359 1-216-097-91 RES, CHIP 100K 5% 1/10W
R360 1-216-097-91 RES, CHIP 100K 5% 1/10W
R361 1-216-049-91 RES, CHIP 1K 5% 1/10W
R362 1-216-049-91 RES, CHIP 1K 5% 1/10W
R401 1-216-085-00 METAL CHIP 33K 5% 1/10W
R402 1-216-085-00 METAL CHIP 33K 5% 1/10W
R403 1-216-085-00 METAL CHIP 33K 5% 1/10W
R301 1-216-042-00 METAL CHIP 510 5% 1/10W
R302 1-216-042-00 METAL CHIP 510 5% 1/10W
R303 1-216-042-00 METAL CHIP 510 5% 1/10W
R304 1-216-021-00 METAL CHIP 68 5% 1/10W
R305 1-216-073-00 METAL CHIP 10K 5% 1/10W
R306 1-216-021-00 METAL CHIP 68 5% 1/10W
R307 1-216-073-00 METAL CHIP 10K 5% 1/10W
R308 1-216-021-00 METAL CHIP 68 5% 1/10W
R309 1-216-097-91 RES, CHIP 100K 5% 1/10W
R310 1-216-042-00 METAL CHIP 510 5% 1/10W
R311 1-216-042-00 METAL CHIP 510 5% 1/10W
R312 1-216-042-00 METAL CHIP 510 5% 1/10W
R313 1-216-097-91 RES, CHIP 100K 5% 1/10W
R314 1-216-097-91 RES, CHIP 100K 5% 1/10W
R315 1-216-097-91 RES, CHIP 100K 5% 1/10W
R316 1-216-097-91 RES, CHIP 100K 5% 1/10W
R317 1-216-073-00 METAL CHIP 10K 5% 1/10W
R404 1-216-085-00 METAL CHIP 33K 5% 1/10W
R405 1-216-085-00 METAL CHIP 33K 5% 1/10W
R406 1-216-077-91 RES, CHIP 15K 5% 1/10W
R407 1-216-077-91 RES, CHIP 15K 5% 1/10W
R408 1-216-085-00 METAL CHIP 33K 5% 1/10W
R409 1-216-025-91 RES, CHIP 100 5% 1/10W
R410 1-216-025-91 RES, CHIP 100 5% 1/10W
R411 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R412 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R413 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R414 1-216-049-91 RES, CHIP 1K 5% 1/10W
R431 1-216-089-91 RES, CHIP 47K 5% 1/10W
R432 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R433 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R434 1-216-089-91 RES, CHIP 47K 5% 1/10W
R435 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R436 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
8-7
Page 92
AU-215 CK-81
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R437 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R438 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R439 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R563 1-216-049-91 RES, CHIP 1K 5% 1/10W
R564 1-216-295-91 SHORT 0
R569 1-216-295-91 SHORT 0
R440 1-216-295-91 SHORT 0
R441 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R443 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R444 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R445 1-216-049-91 RES, CHIP 1K 5% 1/10W
R446 1-216-047-91 RES, CHIP 820 5% 1/10W
R447 1-216-049-91 RES, CHIP 1K 5% 1/10W
R448 1-216-047-91 RES, CHIP 820 5% 1/10W
R449 1-216-109-00 METAL CHIP 330K 5% 1/10W
R450 1-216-109-00 METAL CHIP 330K 5% 1/10W
R451 1-216-041-00 METAL CHIP 470 5% 1/10W
R452 1-216-041-00 METAL CHIP 470 5% 1/10W
R455 1-216-097-91 RES, CHIP 100K 5% 1/10W
R456 1-216-049-91 RES, CHIP 1K 5% 1/10W
R457 1-216-049-91 RES, CHIP 1K 5% 1/10W
R458 1-216-041-00 METAL CHIP 470 5% 1/10W
R459 1-216-041-00 METAL CHIP 470 5% 1/10W
R460 1-216-041-00 METAL CHIP 470 5% 1/10W
R461 1-216-041-00 METAL CHIP 470 5% 1/10W
R501 1-216-089-91 RES, CHIP 47K 5% 1/10W
R502 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R503 1-216-089-91 RES, CHIP 47K 5% 1/10W
R504 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R510 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R511 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R571 1-216-089-91 RES, CHIP 47K 5% 1/10W
R572 1-216-089-91 RES, CHIP 47K 5% 1/10W
R573 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R574 1-216-077-91 RES, CHIP 15K 5% 1/10W
R575 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R576 1-216-077-91 RES, CHIP 15K 5% 1/10W
R577 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R578 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R579 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R580 1-216-079-00 METAL CHIP 18K 5% 1/10W
R585 1-216-109-00 METAL CHIP 330K 5% 1/10W
R586 1-216-109-00 METAL CHIP 330K 5% 1/10W
R587 1-216-041-00 METAL CHIP 470 5% 1/10W
R588 1-216-041-00 METAL CHIP 470 5% 1/10W
R589 1-216-049-91 RES, CHIP 1K 5% 1/10W
R590 1-216-025-91 RES, CHIP 100 5% 1/10W
R591 1-216-025-91 RES, CHIP 100 5% 1/10W
R592 1-216-049-91 RES, CHIP 1K 5% 1/10W
R593 1-216-295-91 SHORT 0
R598 1-216-295-91 SHORT 0
< RELAY >
RY301 1-755-041-11 RELAY
RY302 1-755-041-11 RELAY
R512 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R513 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R514 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R517 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R519 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R520 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R521 1-216-109-00 METAL CHIP 330K 5% 1/10W
R522 1-216-109-00 METAL CHIP 330K 5% 1/10W
R523 1-216-041-00 METAL CHIP 470 5% 1/10W
R524 1-216-041-00 METAL CHIP 470 5% 1/10W
R525 1-216-049-91 RES, CHIP 1K 5% 1/10W
R526 1-216-025-91 RES, CHIP 100 5% 1/10W
R527 1-216-025-91 RES, CHIP 100 5% 1/10W
R528 1-216-049-91 RES, CHIP 1K 5% 1/10W
R541 1-216-089-91 RES, CHIP 47K 5% 1/10W
R542 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R543 1-216-089-91 RES, CHIP 47K 5% 1/10W
R544 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R545 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R546 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R547 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R548 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R549 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R553 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R555 1-216-109-00 METAL CHIP 330K 5% 1/10W
R556 1-216-109-00 METAL CHIP 330K 5% 1/10W
R557 1-216-041-00 METAL CHIP 470 5% 1/10W
R558 1-216-041-00 METAL CHIP 470 5% 1/10W
R559 1-216-049-91 RES, CHIP 1K 5% 1/10W
R560 1-216-025-91 RES, CHIP 100 5% 1/10W
* A-6065-330-A CK-81 BOARD, COMPLETE
*********************
(Ref.No. 2,000 Series)
< CAPACITOR >
C652 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C653 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C654 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C655 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C656 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C657 1-128-551-11 ELECT 22uF 20% 25V
C658 1-126-099-11 ELECT 2.2uF 20% 35V
C659 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C660 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C661 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
< CONNECTOR >
CN651 1-770-165-11 CONNECTOR, FFC/FPC 13P
CN656 1-770-638-11 CONNECTOR, FFC/FPC 7P
* CN657 1-568-951-11 PIN, CONNECTOR 2P
< DIODE >
D651 8-719-069-59 DIODE UDZS-TE17-8.2B
D652 8-719-988-61 DIODE 1SS355TE-17
< IC >
IC651 8-759-473-06 IC BU4011BF-E2
IC652 8-759-522-08 IC BA6780FP-Y-E2
< TRANSISTOR >
R561 1-216-025-91 RES, CHIP 100 5% 1/10W
R562 1-216-049-91 RES, CHIP 1K 5% 1/10W
Q651 8-729-421-22 TRANSISTOR UN2211
Q652 8-729-421-22 TRANSISTOR UN2211
8-8
Page 93
CK-81 CK-88 FL-104
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Q653 8-729-421-22 TRANSISTOR UN2211
Q654 8-729-421-22 TRANSISTOR UN2211
Q656 8-729-120-28 TRANSISTOR 2SC1623-L5L6
< RESISTOR >
R662 1-216-097-91 RES, CHIP 100K 5% 1/10W
R664 1-216-037-00 METAL CHIP 330 5% 1/10W
R665 1-216-073-00 METAL CHIP 10K 5% 1/10W
R666 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R667 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
R668 1-216-075-00 METAL CHIP 12K 5% 1/10W
R669 1-216-081-00 METAL CHIP 22K 5% 1/10W
R670 1-216-081-00 METAL CHIP 22K 5% 1/10W
R671 1-216-081-00 METAL CHIP 22K 5% 1/10W
R672 1-216-081-00 METAL CHIP 22K 5% 1/10W
R673 1-216-081-00 METAL CHIP 22K 5% 1/10W
R674 1-216-081-00 METAL CHIP 22K 5% 1/10W
R675 1-216-081-00 METAL CHIP 22K 5% 1/10W
R676 1-216-081-00 METAL CHIP 22K 5% 1/10W
R677 1-219-397-11 RES, CHIP 1.8 5% 1/8W
R678 1-219-397-11 RES, CHIP 1.8 5% 1/8W
R679 1-219-397-11 RES, CHIP 1.8 5% 1/8W
R681 1-216-049-91 RES, CHIP 1K 5% 1/10W
R682 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R683 1-216-073-00 METAL CHIP 10K 5% 1/10W
R684 1-216-049-91 RES, CHIP 1K 5% 1/10W
R685 1-216-075-00 METAL CHIP 12K 5% 1/10W
R686 1-216-073-00 METAL CHIP 10K 5% 1/10W
R687 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
R688 1-216-295-91 SHORT 0
C216 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C219 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C220 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C221 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C222 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C223 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C224 1-128-131-11 ELECT 22uF 20% 50V
C225 1-128-131-11 ELECT 22uF 20% 50V
C226 1-137-150-11 FILM 0.01uF 5% 100V
C227 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C230 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C231 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C232 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C233 1-128-131-11 ELECT 22uF 20% 50V
C234 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C235 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C236 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C237 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C238 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C239 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C240 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C241 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C242 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C243 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C244 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C245 1-128-131-11 ELECT 22uF 20% 50V
C246 1-128-131-11 ELECT 22uF 20% 50V
C247 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
< CONNECTOR >
* A-6065-336-A CK-88 BOARD, COMPLETE
*********************
(Ref.No. 2,000 Series)
< CONNECTOR >
* CN901 1-568-955-11 PIN, CONNECTOR 6P
* CN902 1-568-934-11 PIN, CONNECTOR 7P
* CN903 1-568-951-11 PIN, CONNECTOR 2P
* A-6065-326-A FL-104 BOARD, COMPLETE
**********************
(Ref.No. 2,000 Series)
3-051-075-02 HOLDER, FL
3-884-241-01 SHEET (C), ADHESIVE
< CAPACITOR >
C201 1-124-589-11 ELECT 47uF 20% 16V
C203 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C204 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C205 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C206 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C207 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C208 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C209 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C211 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C212 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
* CN201 1-568-945-11 PIN, CONNECTOR 7P
CN202 1-793-490-11 CONNECTOR, FFC/FPC 17P
CN203 1-785-730-11 CONNECTOR, FFC/FPC 9P
CN204 1-770-031-11 CONNECTOR, BOARD TO BOARD 7P
* CN205 1-568-941-11 PIN, CONNECTOR 3P
< DIODE >
D202 8-719-988-61 DIODE 1SS355TE-17
D205 8-719-073-03 DIODE MA8082-(K8).S0
D206 8-719-041-97 DIODE MA113-(TX)
D209 8-719-041-97 DIODE MA113-(TX)
D213 8-719-056-06 DIODE SLR-342DCT32 (JOG)
D214 8-719-056-06 DIODE SLR-342DCT32 (MEGA CONTROL)
D215 8-719-018-12 DIODE MA8330-L-TX
D216 8-719-422-67 DIODE MA8062-H-TX
< FERRITE BEAD >
FB201 1-414-135-11 FERRITE 0uH
FB202 1-414-135-11 FERRITE 0uH
FB203 1-414-135-11 FERRITE 0uH
FB204 1-469-324-21 FERRITE 0uH
< IC >
IC201 8-759-640-11 IC M38B57MCH-G221FP
IC202 8-759-326-78 IC PST9140NL
IC203 8-759-356-27 IC NJM2129M-TE2
IC205 8-759-593-18 IC M35501FP-T2
C213 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C214 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C215 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
< COIL >
L201 1-412-533-21 INDUCTOR 47uH
8-9
Page 94
FL-104 FR-154
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< FLUORESCENT INDICATOR >
ND201 1-517-835-11 INDICATOR TUBE, FLUORESCENT
< TRANSISTOR >
R270 1-216-073-00 METAL CHIP 10K 5% 1/10W
R279 1-216-049-91 RES, CHIP 1K 5% 1/10W
R280 1-216-037-00 METAL CHIP 330 5% 1/10W
R281 1-216-049-91 RES, CHIP 1K 5% 1/10W
R283 1-216-025-91 RES, CHIP 100 5% 1/10W
Q201 8-729-808-01 TRANSISTOR 2SD1622-S
Q202 8-729-808-01 TRANSISTOR 2SD1622-S
Q203 8-729-421-22 TRANSISTOR UN2211
Q204 8-729-421-22 TRANSISTOR UN2211
Q205 8-729-421-22 TRANSISTOR UN2211
Q206 8-729-421-22 TRANSISTOR UN2211
Q207 8-729-804-41 TRANSISTOR 2SB1122-S
Q211 8-729-808-01 TRANSISTOR 2SD1622-S
< RESISTOR >
R201 1-208-806-11 RES, CHIP 10K 0.50% 1/10W
R202 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R203 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R204 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R205 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R206 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R207 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R208 1-216-077-91 RES, CHIP 15K 5% 1/10W
R209 1-216-091-00 METAL CHIP 56K 5% 1/10W
R210 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R211 1-208-806-11 RES, CHIP 10K 0.50% 1/10W
R212 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R213 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R214 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R215 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R284 1-216-025-91 RES, CHIP 100 5% 1/10W
R285 1-216-073-00 METAL CHIP 10K 5% 1/10W
R288 1-216-063-91 RES, CHIP 3.9K 5% 1/10W
R289 1-216-073-00 METAL CHIP 10K 5% 1/10W
R290 1-216-025-91 RES, CHIP 100 5% 1/10W
R291 1-216-025-91 RES, CHIP 100 5% 1/10W
R292 1-216-025-91 RES, CHIP 100 5% 1/10W
R293 1-216-025-91 RES, CHIP 100 5% 1/10W
R294 1-216-025-91 RES, CHIP 100 5% 1/10W
R295 1-216-025-91 RES, CHIP 100 5% 1/10W
R296 1-216-093-91 RES, CHIP 68K 5% 1/10W
R298 1-216-031-00 METAL CHIP 180 5% 1/10W
R299 1-216-049-91 RES, CHIP 1K 5% 1/10W
< SWITCH >
S201 1-771-349-21 SWITCH, KEYBOARD (p)
S202 1-771-349-21 SWITCH, KEYBOARD (P)
S208 1-771-349-21 SWITCH, KEYBOARD (JOG)
S209 1-771-349-21 SWITCH, KEYBOARD (MEGA CONTROL)
S212 1-771-349-21 SWITCH, KEYBOARD (§ OPEN/CLOSE)
S213 1-771-349-21 SWITCH, KEYBOARD (·)
S214 1-771-349-21 SWITCH, KEYBOARD (DISC SKIP)
S215 1-771-349-21 SWITCH, KEYBOARD (EX-CHANGE)
S216 1-771-349-21 SWITCH, KEYBOARD (PREV =)
S217 1-771-349-21 SWITCH, KEYBOARD (NEXT +)
R216 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R218 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R219 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R221 1-208-806-11 RES, CHIP 10K 0.50% 1/10W
R222 1-208-806-11 RES, CHIP 10K 0.50% 1/10W
R223 1-208-806-11 RES, CHIP 10K 0.50% 1/10W
R226 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R227 1-216-073-00 METAL CHIP 10K 5% 1/10W
R228 1-216-049-91 RES, CHIP 1K 5% 1/10W
R229 1-216-049-91 RES, CHIP 1K 5% 1/10W
R230 1-216-295-91 SHORT 0
R231 1-216-073-00 METAL CHIP 10K 5% 1/10W
R232 1-216-073-00 METAL CHIP 10K 5% 1/10W
R233 1-216-073-00 METAL CHIP 10K 5% 1/10W
R234 1-216-073-00 METAL CHIP 10K 5% 1/10W
R235 1-216-089-91 RES, CHIP 47K 5% 1/10W
R236 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R237 1-216-025-91 RES, CHIP 100 5% 1/10W
R238 1-216-097-91 RES, CHIP 100K 5% 1/10W
R239 1-216-025-91 RES, CHIP 100 5% 1/10W
R253 1-216-073-00 METAL CHIP 10K 5% 1/10W
R254 1-216-073-00 METAL CHIP 10K 5% 1/10W
R255 1-216-073-00 METAL CHIP 10K 5% 1/10W
R261 1-216-049-91 RES, CHIP 1K 5% 1/10W
R262 1-216-049-91 RES, CHIP 1K 5% 1/10W
R263 1-216-073-00 METAL CHIP 10K 5% 1/10W
R264 1-216-073-00 METAL CHIP 10K 5% 1/10W
R265 1-216-073-00 METAL CHIP 10K 5% 1/10W
R266 1-216-073-00 METAL CHIP 10K 5% 1/10W
R267 1-216-073-00 METAL CHIP 10K 5% 1/10W
S222 1-771-349-21 SWITCH, KEYBOARD (DISC SELECT 5)
S223 1-771-349-21 SWITCH, KEYBOARD (DISC SELECT 4)
< TRANSFORMER >
T201 1-433-841-11 TRANSFORMER, DC-DC CONVERTER
< VIBRATOR >
X201 1-781-282-31 VIBRATOR, CERAMIC (4MHz)
* A-6065-327-A FR-154 BOARD, COMPLETE
**********************
(Ref.No. 2,000 Series)
< CAPACITOR >
C001 1-107-725-11 CERAMIC CHIP 0.1uF 10% 16V
C002 1-124-589-11 ELECT 47uF 20% 16V
< CONNECTOR >
* CN001 1-691-406-11 CONNECTOR, BOARD TO BOARD 7P
< DIODE >
D001 8-719-064-11 DIODE SPR-325MVW (ON/STANDBY)
< IC >
IC001 8-749-011-22 IC GP1U27X
< COIL >
L001 1-414-936-21 INDUCTOR 22uH
8-10
Page 95
FR-154 HP-114 LE-24 LM-59 MB-85
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< TRANSISTOR >
Q001 8-729-421-22 TRANSISTOR UN2211
Q002 8-729-421-22 TRANSISTOR UN2211
* A-6065-332-A LM-59 BOARD, COMPLETE
**********************
< RESISTOR >
R001 1-216-037-00 METAL CHIP 330 5% 1/10W
R002 1-216-033-00 METAL CHIP 220 5% 1/10W
R003 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R004 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R005 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
< SWITCH >
S001 1-771-349-21 SWITCH, KEYBOARD (1/u)
S002 1-771-349-21 SWITCH, KEYBOARD (DISC SELECT 3)
S003 1-771-349-21 SWITCH, KEYBOARD (DISC SELECT 2)
S004 1-771-349-21 SWITCH, KEYBOARD (DISC SELECT 1)
* A-6065-329-A HP-114 BOARD, COMPLETE
**********************
(Ref.No. 2,000 Series)
< CAPACITOR >
C701 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C702 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
< CONNECTOR >
* CN701 1-568-941-11 PIN, CONNECTOR 3P
< DIODE >
* A-6065-334-A MB-85 BOARD, COMPLETE (EXCEPT E)
* A-6065-335-A MB-85 BOARD, COMPLETE (E)
*************************
(Ref.No. 1,000 Series)
< CAPACITOR >
C001 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C002 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C003 1-126-246-11 ELECT CHIP 220uF 20% 4V
C004 1-126-204-11 ELECT CHIP 47uF 20% 16V
C005 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C007 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C008 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C010 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C011 1-125-822-11 TANTALUM 10uF 20% 10V
C012 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C013 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C015 1-126-246-11 ELECT CHIP 220uF 20% 4V
C016 1-125-822-11 TANTALUM 10uF 20% 10V
C017 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C018 1-125-822-11 TANTALUM 10uF 20% 10V
C019 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C201 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C202 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C203 1-125-822-11 TANTALUM 10uF 20% 10V
C204 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
D701 8-719-071-15 DIODE HZM6.8ZWA1TL
D702 8-719-071-15 DIODE HZM6.8ZWA1TL
< FERRITE BEAD >
FB701 1-414-135-11 FERRITE 0uH
FB702 1-414-135-11 FERRITE 0uH
FB703 1-414-135-11 FERRITE 0uH
< JACK >
J701 1-785-505-31 JACK, LARGE TYPE (PHONES)
< VARIABLE RESISTOR >
RV701 1-225-738-11 RES, VAR, CARBON 500/500 (LEVEL)
* A-6065-337-A LE-24 BOARD, COMPLETE
*********************
(Ref.No. 2,000 Series)
< CONNECTOR >
CN850 1-506-481-11 PIN, CONNECTOR 2P
< DIODE >
D850 8-719-069-45 DIODE SELU5E23C-TP15 (DOLBY DIGITAL)
C206 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C209 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C210 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C211 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C212 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C213 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C304 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V
C307 1-125-822-11 TANTALUM 10uF 20% 10V
C309 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C310 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C312 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C313 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C314 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C315 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C316 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C317 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C318 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C319 1-125-822-11 TANTALUM 10uF 20% 10V
C320 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C321 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C322 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C323 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C324 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C325 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C327 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
< RESISTOR >
R850 1-216-041-00 METAL CHIP 470 5% 1/10W
C328 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C329 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C331 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C333 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C334 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
8-11
Page 96
MB-85
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C337 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C338 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C339 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C341 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C343 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C707 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C708 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C709 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C710 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C711 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C344 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C401 1-125-822-11 TANTALUM 10uF 20% 10V
C402 1-126-209-11 ELECT CHIP 100uF 20% 4V
C403 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C404 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C405 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C406 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C408 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C410 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C411 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C413 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C414 1-125-822-11 TANTALUM 10uF 20% 10V
C415 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C416 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C418 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C420 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C422 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C425 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C426 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C428 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C431 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C432 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C433 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C434 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C436 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C712 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C713 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C714 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C715 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C717 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C801 1-126-204-11 ELECT CHIP 47uF 20% 16V
C802 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C803 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C805 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C806 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C807 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C808 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C809 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V
C810 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V
C812 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C813 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C814 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C815 1-110-666-11 ELECT CHIP 22uF 20% 6.3V
C816 1-104-601-11 ELECT CHIP 10uF 20% 10V
C817 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C818 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C819 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C820 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C821 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C822 1-126-204-11 ELECT CHIP 47uF 20% 16V
C438 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C439 1-125-822-11 TANTALUM 10uF 20% 10V
C440 1-125-822-11 TANTALUM 10uF 20% 10V
C441 1-126-209-11 ELECT CHIP 100uF 20% 4V
C443 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C502 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C505 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C506 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C508 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C510 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C512 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C513 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C514 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C515 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C516 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C517 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C601 1-125-822-11 TANTALUM 10uF 20% 10V
C602 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C603 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C604 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C605 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C606 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C607 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C608 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C701 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C823 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C824 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C825 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C830 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C831 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C832 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C833 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C834 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C835 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C836 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C837 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C904 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C905 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C906 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C907 1-125-822-11 TANTALUM 10uF 20% 10V
C908 1-128-391-11 ELECT CHIP 330uF 20% 6.3V
C909 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C910 1-125-822-11 TANTALUM 10uF 20% 10V
C911 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C913 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C914 1-125-822-11 TANTALUM 10uF 20% 10V
C916 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C922 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C923 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C924 1-125-822-11 TANTALUM 10uF 20% 10V
C702 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C703 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C704 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C705 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C706 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C925 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C926 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C927 1-125-822-11 TANTALUM 10uF 20% 10V
C928 1-128-391-11 ELECT CHIP 330uF 20% 6.3V
C929 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
8-12
Page 97
MB-85
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C931 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C932 1-125-822-11 TANTALUM 10uF 20% 10V
C933 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C934 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C935 1-125-822-11 TANTALUM 10uF 20% 10V
C937 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C939 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C940 1-125-822-11 TANTALUM 10uF 20% 10V
< CONNECTOR >
CN001 1-785-728-21 PIN (PC BOARD), CONNECTOR 7P
CN002 1-779-936-11 CONNECTOR, FFC/FPC 18P
CN003 1-779-936-11 CONNECTOR, FFC/FPC 18P
CN004 1-778-772-11 CONNECTOR, FFC/FPC 7P
CN005 1-784-327-11 CONNECTOR, FFC/FPC 28P
CN006 1-774-768-11 CONNECTOR, FFC/FPC 17P
CN007 1-778-274-11 CONNECTOR, FFC/FPC 13P
CN009 1-778-274-11 CONNECTOR, FFC/FPC 13P
CN010 1-573-806-21 PIN, CONNECTOR (1.5mm) (SMD) 6P
* CN012 1-573-768-21 PIN, CONNECTOR (1.5mm) (SMD) 5P
< DIODE >
FB037 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
FB040 1-469-116-21 FERRITE 0uH
FB043 1-500-283-11 INDUCTOR CHIP 0uH
FB047 1-469-116-21 FERRITE 0uH
FB048 1-500-283-11 INDUCTOR CHIP 0uH
FB049 1-469-116-21 FERRITE 0uH
FB050 1-500-283-11 INDUCTOR CHIP 0uH
FB051 1-469-116-21 FERRITE 0uH
FB052 1-500-283-11 INDUCTOR CHIP 0uH
FB053 1-500-283-11 INDUCTOR CHIP 0uH
FB054 1-500-283-11 INDUCTOR CHIP 0uH
FB055 1-500-283-11 INDUCTOR CHIP 0uH
FB056 1-500-283-11 INDUCTOR CHIP 0uH
FB058 1-500-283-11 INDUCTOR CHIP 0uH
FB060 1-500-283-11 INDUCTOR CHIP 0uH
FB061 1-469-116-21 FERRITE 0uH
FB063 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
FB065 1-469-116-21 FERRITE 0uH
FB067 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
FB069 1-469-116-21 FERRITE 0uH
FB071 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
D701 8-719-988-61 DIODE 1SS355TE-17
D801 8-719-941-09 DIODE DAP202U
D802 8-719-988-61 DIODE 1SS355TE-17
D803 8-719-941-09 DIODE DAP202U
D804 8-719-941-86 DIODE DAN202U
D805 8-719-941-86 DIODE DAN202U
D806 8-719-988-61 DIODE 1SS355TE-17
D807 8-719-988-61 DIODE 1SS355TE-17
< FERRITE BEAD >
FB001 1-469-324-21 FERRITE 0uH
FB002 1-469-324-21 FERRITE 0uH
FB003 1-469-324-21 FERRITE 0uH
FB004 1-469-324-21 FERRITE 0uH
FB005 1-469-324-21 FERRITE 0uH
FB006 1-469-324-21 FERRITE 0uH
FB007 1-469-324-21 FERRITE 0uH
FB008 1-469-324-21 FERRITE 0uH
FB010 1-469-116-21 FERRITE 0uH
FB011 1-469-116-21 FERRITE 0uH
FB012 1-469-116-21 FERRITE 0uH
FB014 1-469-116-21 FERRITE 0uH
FB015 1-469-116-21 FERRITE 0uH
FB016 1-216-801-11 METAL CHIP 22 5% 1/16W
FB017 1-469-116-21 FERRITE 0uH
FB018 1-469-116-21 FERRITE 0uH
FB019 1-469-116-21 FERRITE 0uH
FB020 1-469-116-21 FERRITE 0uH
FB021 1-469-116-21 FERRITE 0uH
FB022 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
FB024 1-469-116-21 FERRITE 0uH
FB026 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
FB028 1-469-116-21 FERRITE 0uH
FB029 1-469-324-21 FERRITE 0uH
FB030 1-469-116-21 FERRITE 0uH
FB031 1-469-116-21 FERRITE 0uH
FB032 1-469-116-21 FERRITE 0uH
FB033 1-469-116-21 FERRITE 0uH
FB035 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
FB073 1-469-116-21 FERRITE 0uH
FB075 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
FB077 1-469-116-21 FERRITE 0uH
FB078 1-216-801-11 METAL CHIP 22 5% 1/16W
FB080 1-216-801-11 METAL CHIP 22 5% 1/16W
FB081 1-216-801-11 METAL CHIP 22 5% 1/16W
FB083 1-216-801-11 METAL CHIP 22 5% 1/16W
FB084 1-216-801-11 METAL CHIP 22 5% 1/16W
FB085 1-216-801-11 METAL CHIP 22 5% 1/16W
FB086 1-216-801-11 METAL CHIP 22 5% 1/16W
FB087 1-216-801-11 METAL CHIP 22 5% 1/16W
FB088 1-216-801-11 METAL CHIP 22 5% 1/16W
FB105 1-469-324-21 FERRITE 0uH
FB106 1-469-324-21 FERRITE 0uH
< FILTER >
FL001 1-234-177-21 FILTER, CHIP EMI
FL002 1-234-177-21 FILTER, CHIP EMI
FL003 1-233-893-21 FILTER, CHIP EMI
FL004 1-233-893-21 FILTER, CHIP EMI
FL005 1-234-177-21 FILTER, CHIP EMI
FL006 1-234-177-21 FILTER, CHIP EMI
FL008 1-234-177-21 FILTER, CHIP EMI
FL009 1-234-177-21 FILTER, CHIP EMI
FL010 1-234-177-21 FILTER, CHIP EMI
FL011 1-234-177-21 FILTER, CHIP EMI
FL013 1-233-893-21 FILTER, CHIP EMI
FL014 1-234-177-21 FILTER, CHIP EMI
FL015 1-234-177-21 FILTER, CHIP EMI
FL016 1-234-177-21 FILTER, CHIP EMI
FL202 1-234-177-21 FILTER, CHIP EMI
FL203 1-234-177-21 FILTER, CHIP EMI
FL204 1-234-177-21 FILTER, CHIP EMI
FL205 1-234-177-21 FILTER, CHIP EMI
FL301 1-234-177-21 FILTER, CHIP EMI
FL302 1-234-177-21 FILTER, CHIP EMI
FL303 1-234-177-21 FILTER, CHIP EMI
FL401 1-234-177-21 FILTER, CHIP EMI
FL402 1-234-177-21 FILTER, CHIP EMI
8-13
Page 98
MB-85
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
FL403 1-234-177-21 FILTER, CHIP EMI
FL404 1-234-177-21 FILTER, CHIP EMI
FL405 1-234-177-21 FILTER, CHIP EMI
FL501 1-234-177-21 FILTER, CHIP EMI
FL502 1-234-177-21 FILTER, CHIP EMI
FL503 1-234-177-21 FILTER, CHIP EMI
FL601 1-234-177-21 FILTER, CHIP EMI
FL602 1-234-177-21 FILTER, CHIP EMI
FL701 1-234-177-21 FILTER, CHIP EMI
FL904 1-234-177-21 FILTER, CHIP EMI
< IC >
IC001 8-759-594-91 IC SM8701AM-E2
IC003 8-759-531-92 IC TC7WH04FU (TE12R)
IC004 8-759-531-92 IC TC7WH04FU (TE12R)
IC005 8-759-486-55 IC NJM2370U33-TE2
IC201 8-759-469-25 IC AK6440AF-E2
IC202 8-759-599-39 IC MB91101PFV-G-BND-R
IC203 8-759-580-60 IC SN74AHCT08PWR
IC204 8-759-573-65 IC IDT71V016S20PHAU-TL
IC205 8-759-581-30 IC MBM29LV160B-260B-10
IC207 8-759-427-92 IC PST9126NL
IC302 8-759-486-55 IC NJM2370U33-TE2
IC303 8-759-567-27 IC CXD8784R
IC304 8-759-567-35 IC KM416V1200CT-L6T
IC401 8-752-398-60 IC CXD1930BQ
IC402 8-759-567-34 IC KM416S1020CT-G10T
IC403 8-759-567-34 IC KM416S1020CT-G10T
IC404 8-759-486-55 IC NJM2370U33-TE2
IC501 8-752-400-43 IC CXD1901AR
IC502 8-752-390-12 IC CXD1857Q
IC601 8-759-591-83 IC CXD9515Q
IC602 8-759-567-55 IC KM29V16000AT-T
IC701 8-759-598-87 IC CXD8791AQ
IC702 8-759-337-40 IC NJM2904V (TE2)
IC801 8-759-522-13 IC BA5981FP-E2
IC802 8-759-567-26 IC BA5983FP-E2
IC803 8-759-338-78 IC BA10324AFV-E2
IC902 8-759-572-26 IC CXD8799N-T2
IC904 8-759-052-52 IC L78M05T-FA
IC905 8-759-572-26 IC CXD8799N-T2
IC906 8-759-572-26 IC CXD8799N-T2
R006 1-216-821-11 METAL CHIP 1K 5% 1/16W
R007 1-216-864-11 METAL CHIP 0 5% 1/16W
R009 1-216-864-11 METAL CHIP 0 5% 1/16W
R010 1-216-801-11 METAL CHIP 22 5% 1/16W
R014 1-216-801-11 METAL CHIP 22 5% 1/16W
R016 1-216-821-11 METAL CHIP 1K 5% 1/16W
R023 1-216-821-11 METAL CHIP 1K 5% 1/16W
R030 1-216-821-11 METAL CHIP 1K 5% 1/16W
R035 1-216-833-91 RES, CHIP 10K 5% 1/16W
R036 1-216-821-11 METAL CHIP 1K 5% 1/16W
R037 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R040 1-216-864-11 METAL CHIP 0 5% 1/16W
R044 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R045 1-216-833-91 RES, CHIP 10K 5% 1/16W
R053 1-216-833-91 RES, CHIP 10K 5% 1/16W
R202 1-216-801-11 METAL CHIP 22 5% 1/16W
R203 1-216-833-91 RES, CHIP 10K 5% 1/16W
R204 1-216-833-91 RES, CHIP 10K 5% 1/16W
R205 1-216-845-11 METAL CHIP 100K 5% 1/16W
R206 1-216-845-11 METAL CHIP 100K 5% 1/16W
R207 1-216-833-91 RES, CHIP 10K 5% 1/16W
R212 1-216-813-11 METAL CHIP 220 5% 1/16W
R213 1-216-801-11 METAL CHIP 22 5% 1/16W
R217 1-216-833-91 RES, CHIP 10K 5% 1/16W
R222 1-216-833-91 RES, CHIP 10K 5% 1/16W
R223 1-216-833-91 RES, CHIP 10K 5% 1/16W
R225 1-216-833-91 RES, CHIP 10K 5% 1/16W
R226 1-216-833-91 RES, CHIP 10K 5% 1/16W
R227 1-216-813-11 METAL CHIP 220 5% 1/16W
R228 1-216-813-11 METAL CHIP 220 5% 1/16W
R229 1-216-813-11 METAL CHIP 220 5% 1/16W
R230 1-216-813-11 METAL CHIP 220 5% 1/16W
R231 1-216-813-11 METAL CHIP 220 5% 1/16W
R232 1-216-813-11 METAL CHIP 220 5% 1/16W
R235 1-216-864-11 METAL CHIP 0 5% 1/16W
R237 1-216-246-00 RES, CHIP 100K 5% 1/8W
R238 1-216-216-00 RES, CHIP 5.6K 5% 1/8W
R239 1-216-230-00 RES, CHIP 22K 5% 1/8W
R240 1-216-246-00 RES, CHIP 100K 5% 1/8W
R241 1-216-216-00 RES, CHIP 5.6K 5% 1/8W
(E)
(E)
(E)
IC907 8-759-572-26 IC CXD8799N-T2
< COIL >
L001 1-414-754-11 INDUCTOR 10uH
L402 1-414-754-11 INDUCTOR 10uH
< TRANSISTOR >
Q801 8-729-015-74 TRANSISTOR UN5111-TX
Q802 8-729-230-63 TRANSISTOR 2SC4116-YG
Q803 8-729-230-63 TRANSISTOR 2SC4116-YG
< RESISTOR >
R001 1-216-833-91 RES, CHIP 10K 5% 1/16W
R002 1-216-833-91 RES, CHIP 10K 5% 1/16W
R003 1-216-833-91 RES, CHIP 10K 5% 1/16W
R004 1-216-821-11 METAL CHIP 1K 5% 1/16W
R005 1-216-821-11 METAL CHIP 1K 5% 1/16W
R305 1-218-879-11 RES, CHIP 22K 0.50% 1/16W
R306 1-218-831-11 RES, CHIP 220 0.50% 1/16W
R307 1-218-883-11 RES, CHIP 33K 0.50% 1/16W
R308 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R309 1-216-838-11 METAL CHIP 27K 5% 1/16W
R310 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R311 1-216-821-11 METAL CHIP 1K 5% 1/16W
R313 1-216-833-91 RES, CHIP 10K 5% 1/16W
R314 1-216-833-91 RES, CHIP 10K 5% 1/16W
R315 1-216-833-91 RES, CHIP 10K 5% 1/16W
R316 1-218-855-11 RES, CHIP 2.2K 0.50% 1/16W
R317 1-218-871-11 RES, CHIP 10K 0.50% 1/16W
R318 1-216-849-11 METAL CHIP 220K 5% 1/16W
R319 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R320 1-218-853-11 RES, CHIP 1.8K 0.50% 1/16W
R321 1-218-847-11 RES, CHIP 1K 0.50% 1/16W
R322 1-218-871-11 RES, CHIP 10K 0.50% 1/16W
R323 1-216-833-91 RES, CHIP 10K 5% 1/16W
8-14
Page 99
MB-85
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R324 1-216-833-91 RES, CHIP 10K 5% 1/16W
R325 1-216-833-91 RES, CHIP 10K 5% 1/16W
R647 1-216-833-91 RES, CHIP 10K 5% 1/16W
R701 1-216-805-11 METAL CHIP 47 5% 1/16W
R326 1-216-833-91 RES, CHIP 10K 5% 1/16W
R327 1-216-833-91 RES, CHIP 10K 5% 1/16W
R328 1-216-833-91 RES, CHIP 10K 5% 1/16W
R329 1-216-833-91 RES, CHIP 10K 5% 1/16W
R330 1-216-833-91 RES, CHIP 10K 5% 1/16W
R331 1-216-833-91 RES, CHIP 10K 5% 1/16W
R332 1-216-833-91 RES, CHIP 10K 5% 1/16W
R337 1-216-809-11 METAL CHIP 100 5% 1/16W
R338 1-216-833-91 RES, CHIP 10K 5% 1/16W
R339 1-216-833-91 RES, CHIP 10K 5% 1/16W
R340 1-216-833-91 RES, CHIP 10K 5% 1/16W
R341 1-216-809-11 METAL CHIP 100 5% 1/16W
R403 1-216-833-91 RES, CHIP 10K 5% 1/16W
R404 1-216-864-11 METAL CHIP 0 5% 1/16W
R405 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R406 1-216-822-11 METAL CHIP 1.2K 5% 1/16W
R407 1-216-833-91 RES, CHIP 10K 5% 1/16W
R409 1-216-864-11 METAL CHIP 0 5% 1/16W
R410 1-216-821-11 METAL CHIP 1K 5% 1/16W
R411 1-216-833-91 RES, CHIP 10K 5% 1/16W
R412 1-216-809-11 METAL CHIP 100 5% 1/16W
R426 1-216-813-11 METAL CHIP 220 5% 1/16W
R427 1-216-813-11 METAL CHIP 220 5% 1/16W
R428 1-216-813-11 METAL CHIP 220 5% 1/16W
R429 1-216-813-11 METAL CHIP 220 5% 1/16W
R702 1-216-817-11 METAL CHIP 470 5% 1/16W
R703 1-216-817-11 METAL CHIP 470 5% 1/16W
R704 1-216-817-11 METAL CHIP 470 5% 1/16W
R705 1-216-817-11 METAL CHIP 470 5% 1/16W
R706 1-216-821-11 METAL CHIP 1K 5% 1/16W
R707 1-216-844-11 METAL CHIP 82K 5% 1/16W
R708 1-216-844-11 METAL CHIP 82K 5% 1/16W
R709 1-216-844-11 METAL CHIP 82K 5% 1/16W
R710 1-216-844-11 METAL CHIP 82K 5% 1/16W
R711 1-216-833-91 RES, CHIP 10K 5% 1/16W
R712 1-216-839-11 METAL CHIP 33K 5% 1/16W
R720 1-216-821-11 METAL CHIP 1K 5% 1/16W
R721 1-216-821-11 METAL CHIP 1K 5% 1/16W
R722 1-216-801-11 METAL CHIP 22 5% 1/16W
R748 1-216-833-91 RES, CHIP 10K 5% 1/16W
R751 1-216-821-11 METAL CHIP 1K 5% 1/16W
R752 1-216-821-11 METAL CHIP 1K 5% 1/16W
R755 1-216-830-11 METAL CHIP 5.6K 5% 1/16W
R757 1-216-864-11 METAL CHIP 0 5% 1/16W
R758 1-216-864-11 METAL CHIP 0 5% 1/16W
R801 1-216-841-11 METAL CHIP 47K 5% 1/16W
R802 1-216-841-11 METAL CHIP 47K 5% 1/16W
R803 1-216-841-11 METAL CHIP 47K 5% 1/16W
R804 1-216-841-11 METAL CHIP 47K 5% 1/16W
R805 1-216-840-11 METAL CHIP 39K 5% 1/16W
R430 1-216-813-11 METAL CHIP 220 5% 1/16W
R431 1-216-813-11 METAL CHIP 220 5% 1/16W
R501 1-216-809-11 METAL CHIP 100 5% 1/16W
R519 1-216-809-11 METAL CHIP 100 5% 1/16W
R520 1-216-833-91 RES, CHIP 10K 5% 1/16W
R521 1-216-833-91 RES, CHIP 10K 5% 1/16W
R522 1-216-833-91 RES, CHIP 10K 5% 1/16W
R527 1-216-833-91 RES, CHIP 10K 5% 1/16W
R528 1-216-833-91 RES, CHIP 10K 5% 1/16W
R530 1-216-864-11 METAL CHIP 0 5% 1/16W
R537 1-216-806-11 RES, CHIP 56 5% 1/16W
R539 1-216-864-11 METAL CHIP 0 5% 1/16W
R540 1-216-864-11 METAL CHIP 0 5% 1/16W
R541 1-216-864-11 METAL CHIP 0 5% 1/16W
R543 1-216-864-11 METAL CHIP 0 5% 1/16W
R544 1-216-864-11 METAL CHIP 0 5% 1/16W
R604 1-216-833-91 RES, CHIP 10K 5% 1/16W
R605 1-216-833-91 RES, CHIP 10K 5% 1/16W
R606 1-216-833-91 RES, CHIP 10K 5% 1/16W
R630 1-216-833-91 RES, CHIP 10K 5% 1/16W
R631 1-216-833-91 RES, CHIP 10K 5% 1/16W
R632 1-216-833-91 RES, CHIP 10K 5% 1/16W
R633 1-216-833-91 RES, CHIP 10K 5% 1/16W
R634 1-216-833-91 RES, CHIP 10K 5% 1/16W
R635 1-216-833-91 RES, CHIP 10K 5% 1/16W
R806 1-216-840-11 METAL CHIP 39K 5% 1/16W
R807 1-216-835-11 METAL CHIP 15K 5% 1/16W
R808 1-216-835-11 METAL CHIP 15K 5% 1/16W
R809 1-216-844-11 METAL CHIP 82K 5% 1/16W
R810 1-216-844-11 METAL CHIP 82K 5% 1/16W
R812 1-216-845-11 METAL CHIP 100K 5% 1/16W
R813 1-216-845-11 METAL CHIP 100K 5% 1/16W
R815 1-216-836-11 METAL CHIP 18K 5% 1/16W
R816 1-216-845-11 METAL CHIP 100K 5% 1/16W
R817 1-216-852-11 METAL CHIP 390K 5% 1/16W
R818 1-216-852-11 METAL CHIP 390K 5% 1/16W
R819 1-216-849-11 METAL CHIP 220K 5% 1/16W
R820 1-216-851-11 METAL CHIP 330K 5% 1/16W
R821 1-216-840-11 METAL CHIP 39K 5% 1/16W
R822 1-216-845-11 METAL CHIP 100K 5% 1/16W
R823 1-216-833-91 RES, CHIP 10K 5% 1/16W
R824 1-216-833-91 RES, CHIP 10K 5% 1/16W
R825 1-216-830-11 METAL CHIP 5.6K 5% 1/16W
R826 1-216-830-11 METAL CHIP 5.6K 5% 1/16W
R827 1-216-851-11 METAL CHIP 330K 5% 1/16W
R828 1-216-837-11 METAL CHIP 22K 5% 1/16W
R829 1-216-837-11 METAL CHIP 22K 5% 1/16W
R831 1-216-833-91 RES, CHIP 10K 5% 1/16W
R832 1-216-833-91 RES, CHIP 10K 5% 1/16W
R834 1-216-847-11 METAL CHIP 150K 5% 1/16W
R636 1-216-815-11 METAL CHIP 330 5% 1/16W
R637 1-216-809-11 METAL CHIP 100 5% 1/16W
R638 1-216-809-11 METAL CHIP 100 5% 1/16W
R639 1-216-809-11 METAL CHIP 100 5% 1/16W
R640 1-216-809-11 METAL CHIP 100 5% 1/16W
R641 1-216-809-11 METAL CHIP 100 5% 1/16W
R642 1-216-809-11 METAL CHIP 100 5% 1/16W
R643 1-216-815-11 METAL CHIP 330 5% 1/16W
R835 1-216-847-11 METAL CHIP 150K 5% 1/16W
R836 1-216-847-11 METAL CHIP 150K 5% 1/16W
R837 1-216-844-11 METAL CHIP 82K 5% 1/16W
R838 1-216-848-11 METAL CHIP 180K 5% 1/16W
R839 1-216-848-11 METAL CHIP 180K 5% 1/16W
R840 1-216-848-11 METAL CHIP 180K 5% 1/16W
R841 1-216-843-11 METAL CHIP 68K 5% 1/16W
R842 1-216-844-11 METAL CHIP 82K 5% 1/16W
8-15
Page 100
MB-85 POWER BLOCK
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R843 1-216-844-11 METAL CHIP 82K 5% 1/16W
R844 1-216-843-11 METAL CHIP 68K 5% 1/16W
R845 1-216-843-11 METAL CHIP 68K 5% 1/16W
R846 1-216-841-11 METAL CHIP 47K 5% 1/16W
R847 1-216-296-91 SHORT 0
R851 1-216-833-91 RES, CHIP 10K 5% 1/16W
R852 1-216-833-91 RES, CHIP 10K 5% 1/16W
R853 1-216-833-91 RES, CHIP 10K 5% 1/16W
R854 1-216-833-91 RES, CHIP 10K 5% 1/16W
R855 1-216-834-11 METAL CHIP 12K 5% 1/16W
R856 1-216-836-11 METAL CHIP 18K 5% 1/16W
R857 1-218-899-11 RES, CHIP 150K 0.50% 1/16W
R858 1-218-899-11 RES, CHIP 150K 0.50% 1/16W
R859 1-218-889-11 RES, CHIP 56K 0.50% 1/16W
R860 1-218-889-11 RES, CHIP 56K 0.50% 1/16W
R861 1-216-296-91 SHORT 0
R864 1-216-138-00 METAL CHIP 3.3 5% 1/8W
R867 1-216-833-91 RES, CHIP 10K 5% 1/16W
R868 1-216-833-91 RES, CHIP 10K 5% 1/16W
R869 1-216-833-91 RES, CHIP 10K 5% 1/16W
R870 1-216-815-11 METAL CHIP 330 5% 1/16W
R871 1-216-817-11 METAL CHIP 470 5% 1/16W
R872 1-216-815-11 METAL CHIP 330 5% 1/16W
R873 1-216-821-11 METAL CHIP 1K 5% 1/16W
R909 1-216-809-11 METAL CHIP 100 5% 1/16W
R912 1-216-809-11 METAL CHIP 100 5% 1/16W
R915 1-216-809-11 METAL CHIP 100 5% 1/16W
R918 1-216-809-11 METAL CHIP 100 5% 1/16W
< COMPOSITION CIRCUIT BLOCK >
C212 1-111-090-11 ELECT 560uF 35V
C213 1-126-947-11 ELECT 47uF 35V
C301 1-126-960-11 ELECT 1uF 50V
C311 1-111-090-11 ELECT 560uF 35V
C313 1-126-942-11 ELECT 1000uF 25V
C315 1-126-964-11 ELECT 10uF 50V
C511 1-126-942-11 ELECT 1000uF 25V
C512 1-126-947-11 ELECT 47uF 35V
C611 1-111-087-11 ELECT 330uF 35V
C612 1-111-087-11 ELECT 330uF 35V
C613 1-126-947-11 ELECT 47uF 35V
< DIODE >
D101 9-884-089-01 DIODE S1WBA60
D102 8-719-160-68 DIODE RD18FB2 (HS-034SF)
D104 8-719-109-57 DIODE RD2.4ESB2
D105 9-980-073-01 DIODE 1SS270A
D106 9-880-435-01 DIODE D1N60
D109 9-880-435-01 DIODE D1N60
D211 9-884-584-01 DIODE SF6L20U
D311 8-719-500-50 DIODE D3S4M
D312 9-980-073-01 DIODE 1SS270A
D511 8-719-027-43 DIODE S2L20U
D611 8-719-500-50 DIODE D3S4M
D612 8-719-160-68 DIODE RD18FB2
D613 9-980-073-01 DIODE 1SS270A
< FUSE >
! F101 1-532-388-31 FUSE (2A/250V) (HS-034SF)
! F101 1-533-296-11 FUSE (2A/125V) (HS-034SU)
* RB201 1-233-270-11 NETWORK, RES (8 GANG) 10K
* RB202 1-233-270-11 NETWORK, RES (8 GANG) 10K
* RB203 1-233-270-11 NETWORK, RES (8 GANG) 10K
* RB204 1-233-270-11 NETWORK, RES (8 GANG) 10K
* RB601 1-233-270-11 NETWORK, RES (8 GANG) 10K
< VARIABLE RESISTOR >
RV401 1-223-583-11 RES, ADJ, CARBON 1K
< VIBRATOR >
X001 1-781-188-21 OSCILLATOR, CRYSTAL (27MHz)
X201 1-781-185-21 VIBRATOR, CERAMIC (12.5MHz)
* 1-468-372-11 POWER BLOCK (HS-034SU) (US, Canadian)
* 1-468-372-21 POWER BLOCK (HS-034SF) (E, PX)
**********************
(Ref.No. 6,000 Series)
< CAPACITOR >
! C101 1-115-165-11 FILM 0.1uF 250V
! C102 1-115-165-11 FILM 0.1uF 250V
C110 1-113-607-11 ELECT 330uF 400V
(HS-034SF)
C110 9-884-583-01 ELECT 270uF 200V
(HS-034SU)
C114 1-107-967-11 ELECT 1uF 400V
C211 1-111-090-11 ELECT 560uF 35V
< IC >
IC301 8-759-420-19 IC AN1431T
< IC LINK >
! P211 1-533-588-11 IC LINK 500mA
! P311 1-533-593-11 IC LINK 2A
! P312 1-533-589-11 IC LINK 750mA
! P511 1-533-589-11 IC LINK 750mA
! P611 1-533-593-11 IC LINK 2A
< PHOTO COUPLER >
! PC101 8-749-010-59 PHOTO COUPLER TLP721F
< TRANSISTOR >
Q101 8-729-039-75 TRANSISTOR 2SK2185 (HS-034SU)
Q101 9-880-450-01 TRANSISTOR 2SK2333 (HS-034SF)
Q102 8-729-023-98 TRANSISTOR 2SC3377
Q103 8-729-039-75 TRANSISTOR 2SK2185 (HS-034SU)
Q103 9-880-450-01 TRANSISTOR 2SK2333 (HS-034SF)
Q211 9-884-585-01 TRANSISTOR 2SJ490
Q311 9-980-439-01 TRANSISTOR 2SJ488
Q312 8-729-900-95 TRANSISTOR 2SC1740S
Q511 9-880-440-01 TRANSISTOR 2SK2279
Q512 8-729-901-52 TRANSISTOR 2SA933S
Q611 8-729-921-42 TRANSISTOR 2SA1679
8-16
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Loading...