Sony DSLR-A230 annexe 4 Instruction Manual
Preparing the camera
Before your operation
Shooting images
Using the shooting
function
Using the viewing
function
Changing your setup
Viewing images on a
computer
Printing images
Additional information on this product and
answers to frequently asked questions can be
found at our Customer Support Website.
Printed on 70% or more recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
Digital Single Lens Reflex Camera
Instruction Manual
DSLR-A230
Owner’s Record
The model and serial numbers are located
on the bottom.
Record the serial number in the space
provided below.
Refer to these numbers whenever you call
upon your Sony dealer regarding this
product.
Model No. DSLR-A230
Serial No. __________________________
WARNING
To reduce fire or shock hazard, do
not expose the unit to rain or
moisture.
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE
INSTRUCTIONS.
DANGER - TO
REDUCE THE RISK
OF FIRE OR
ELECTRIC SHOCK,
CAREFULLY
FOLLOW THESE
INSTRUCTIONS.
If the shape of the plug does not fit the
power outlet, use an attachment plug
adaptor of the proper configuration for the
power outlet.
Caution
Battery pack
If the battery pack is mishandled, the
battery pack can burst, cause a fire or even
chemical burns. Observe the following
cautions.
• Do not disassemble.
• Do not crush and do not expose the
battery pack to any shock or force such as
hammering, dropping or stepping on it.
• Do not short circuit and do not allow
metal objects to come into contact with
the battery terminals.
• Do not expose to high temperature above
60°C (140°F) such as in direct sunlight or
in a car parked in the sun.
• Do not incinerate or dispose of in fire.
• Do not handle damaged or leaking
lithium ion batteries.
• Be sure to charge the battery pack using a
genuine Sony battery charger or a device
that can charge the battery pack.
2
• Keep the battery pack out of the reach of
small children.
• Keep the battery pack dry.
• Replace only with the same or equivalent
type recommended by Sony.
• Dispose of used battery pack promptly
described the instructions.
Battery charger
Even if the CHARGE lamp is not lit, the
battery charger is not disconnected from the
AC power source (mains) as long as it is
connected to the wall outlet (wall socket).
If some trouble occurs while using the
battery charger, immediately shut off the
power by disconnecting the plug from the
wall outlet (wall socket).
For Customers in the U.S.A.
and Canada
RECYCLING LITHIUM-ION
BATTERIES
Lithium-Ion batteries are
recyclable.
You can help preserve
our environment by
returning your used
rechargeable batteries to
the collection and
recycling location nearest you.
For more information regarding recycling
of rechargeable batteries, call toll free
1-800-822-8837, or visit http://
www.rbrc.org/
Caution: Do not handle damaged or
leaking Lithium-Ion batteries.
Battery pack
This device complies with Part 15 of the
FCC Rules, Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This Class B digital apparatus complies
with Canadian ICES-003.
For Customers in the U.S.A.
UL is an internationally recognized safety
organization.
The UL Mark on the product means it has
been UL Listed.
If you have any questions about this
product, you may call:
Sony Customer Information Services
Center
1-800-222-SONY (7669)
The number below is for the FCC related
matters only.
Regulatory Information
Declaration of Conformity
Trade Name: SONY
Model No.: DSLR-A230
Responsible Party: Sony Electronics
Inc.
Address:16530 Via Esprillo,
San Diego, CA 92127 U.S.A.
Telephone No.: 858-942-2230
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
3
Note:
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the
following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
The supplied interface cable must be used
with the equipment in order to comply with
the limits for a digital device pursuant to
Subpart B of Part 15 of FCC Rules.
For Customers in Europe
Notice for the customers in the
countries applying EU Directives
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku
Tokyo, 108-0075 Japan. The Authorized
Representative for EMC and product safety
is Sony Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart, Germany. For
any service or guarantee matters please
refer to the addresses given in separate
service or guarantee documents.
This product has been tested and found
compliant with the limits set out in the
EMC Directive for using connection cables
shorter than 3 meters (9.8 feet).
Attention
The electromagnetic fields at the specific
frequencies may influence the picture and
sound of this unit.
Notice
If static electricity or electromagnetism
causes data transfer to discontinue midway
(fail), restart the application or disconnect
and connect the communication cable
(USB, etc.) again.
4
Disposal of Old Electrical &
Electronic Equipment (Applicable in
the European Union and other
European countries with separate
collection systems)
This symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead it
shall be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment. By
ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise
be caused by inappropriate waste handling
of this product. The recycling of materials
will help to conserve natural resources. For
more detailed information about recycling
of this product, please contact your local
Civic Office, your household waste
disposal service or the shop where you
purchased the product.
Disposal of waste batteries
(applicable in the European Union
and other European countries with
separate collection systems)
This symbol on the battery or on the
packaging indicates that the battery
provided with this product shall not be
treated as household waste.
By ensuring these batteries are disposed of
correctly, you will help prevent potentially
negative consequences for the environment
and human health which could otherwise be
caused by inappropriate waste handling of
the battery. The recycling of the materials
will help to conserve natural resources.
In case of products that for safety,
performance or data integrity reasons
require a permanent connection with an
incorporated battery, this battery should be
replaced by qualified service staff only.
To ensure that the battery will be treated
properly, hand over the product at end-oflife to the applicable collection point for the
recycling of electrical and electronic
equipment.
For all other batteries, please view the
section on how to remove the battery from
the product safely. Hand the battery over to
the applicable collection point for the
recycling of waste batteries.
For more detailed information about
recycling of this product or battery, please
contact your local Civic Office, your
household waste disposal service or the
shop where you purchased the product.
5
Notice for customers in the
United Kingdom
A moulded plug complying with BS 1363
is fitted to this equipment for your safety
and convenience.
Should the fuse in the plug supplied need to
be replaced, a fuse of the same rating as the
supplied one and approved by ASTA or
BSI to BS 1362, (i.e., marked with an or
mark) must be used.
If the plug supplied with this equipment has
a detachable fuse cover, be sure to attach
the fuse cover after you change the fuse.
Never use the plug without the fuse cover.
If you should lose the fuse cover, please
contact your nearest Sony service station.
6
Notes on using your camera
No compensation for contents of the
recording
The contents of the recording cannot be
compensated for if recording or playback is
not possible due to a malfunction of your
camera or a memory card, etc.
Back up recommendation
To avoid the potential risk of data loss,
always copy (back up) data to other
medium.
Notes on the LCD monitor and lens
• The LCD monitor is manufactured using
extremely high-precision technology so
over 99.99% of the pixels are operational
for effective use. However, there may be
some tiny black points and/or bright
points (white, red, blue or green in color)
that constantly appear on the LCD
monitor. These points are normal in the
manufacturing process and do not affect
the images in any way.
Black, white, red,
blue and green
points
• Do not expose the camera to direct
sunlight. If sunlight is focused on a
nearby object, it may cause a fire. When
you must place the camera under direct
sunlight, attach the lens cap.
• Images may trail across on the LCD
monitor in a cold location. This is not a
malfunction. When turning on the camera
in a cold location, the LCD monitor may
become temporarily dark. When the
camera warms up, the monitor will
function normally.
• Do not press against the LCD monitor.
The monitor may be discolored and that
may cause a malfunction.
Warning on copyright
Television programs, films, videotapes, and
other materials may be copyrighted.
Unauthorized recording of such materials
may be contrary to the provisions of the
copyright laws.
The pictures used in this manual
The photographs used as examples of
pictures in this manual are reproduced
images, and are not actual images shot
using this camera.
On the data specifications described
in this Instruction Manual
The data on performance and specifications
is defined under the following conditions,
except as described in this Instruction
Manual: at an ordinary ambient
temperature of 25ºC (77°F), and using a
fully charged battery pack.
7
Table of Contents
Notes on using your camera .............................................. 7
Preparing the
camera
Before your
operation
Shooting images
Checking the accessories supplied .................................. 11
Preparing the battery pack ............................................... 12
Attaching a lens ............................................................... 18
Inserting a memory card .................................................. 20
Preparing the camera ....................................................... 23
Using the accessories supplied ........................................ 25
Checking the number of recordable images .................... 27
Cleaning ........................................................................... 29
Identifying parts and screen indicators ............................ 32
Front side .................................................................... 32
Rear side ..................................................................... 33
Sides/Bottom .............................................................. 34
Switching the recording information display (DISP)
............................................................................ 35
LCD monitor (Graphic Display) ................................ 36
LCD monitor (Standard Display) ............................... 38
Viewfinder .................................................................. 40
Selecting a function/setting ............................................. 41
The functions selected by the Control button ............ 42
The functions selected by the Fn (Function) button ... 43
The functions selected by the MENU button ............. 43
Shooting an image without camera shake ....................... 45
Correct posture ........................................................... 45
Using the SteadyShot function ................................... 46
Using a tripod ............................................................. 47
/ Shooting with the automatic setting............... 48
Shooting with a suitable setting for the subject (Scene
Selection) .................................................................... 51
Taking portrait photos .......................................... 52
Taking landscape photos ...................................... 53
Taking small-subject photos ................................ 54
Taking moving-subject photos ............................. 55
Taking sunset photos ........................................... 56
Taking night view photos .................................... 57
8
Using the
shooting function
Shooting an image the way you want it (Exposure mode)
..................................................................................... 58
Shooting with program auto .................................. 60
Shooting by controlling the blur of the background
(Aperture priority) ............................................. 61
Shooting a moving subject with various expressions
(Shutter speed priority) ..................................... 63
Shooting with the exposure adjusted manually
(Manual exposure) ............................................ 65
Shooting trails with long exposure (BULB) .......... 67
Selecting the focus method .............................................. 69
Using autofocus .......................................................... 69
Shooting with your desired composition (Focus-lock)
............................................................................ 71
Selecting the focus method to suit the movement of the
subject (Autofocus mode) ................................. 72
Selecting the focus area (AF area) ............................. 73
Adjusting the focus manually (Manual focus) ........... 74
Using the flash ................................................................. 75
Performing wireless flash shooting ............................ 78
Adjusting the brightness of the image (Exposure, Flash
compensation, Metering) ............................................ 79
Using brightness compensation for the entire image
(Exposure compensation) .................................. 79
Adjusting the amount of flash light (Flash compensation)
............................................................................ 80
Selecting the method for measuring the brightness of a
subject (Metering mode) ................................... 81
Setting ISO ...................................................................... 82
Adjusting the color tones (White balance) ...................... 83
Adjusting the white balance to suit a specific light source
(Auto/Preset white balance) .............................. 83
Registering the color tones (Custom white balance) .. 84
9
Image processing ............................................................. 86
Correcting the brightness of the image (D-Range
Optimizer) ......................................................... 86
Selecting your desired image processing (Creative Style)
............................................................................ 86
Changing the range of color reproduction (Color Space)
............................................................................ 88
Selecting the drive mode .................................... 89
Shooting single shot ................................................... 89
Shooting continuously ................................................ 89
Using the self-timer .................................................... 90
Shooting images with the exposure shifted (Exposure
bracket) .............................................................. 91
Shooting with the Remote Commander ..................... 93
Using the viewing
function
Changing your
setup
Viewing images
on a computer
Printing images
Others
Playing back images ........................................................ 94
Checking the information of recorded images ................ 98
Protecting images (Protect) ........................................... 101
Deleting images (Delete) ............................................... 102
Viewing images on a TV screen .................................... 104
Setting image size and image quality ............................ 108
Setting the method for recording on a memory card ..... 110
Changing the noise reduction setting ............................ 112
Changing the functions of the control dial .................... 113
Changing other settings ................................................. 114
Setting the LCD monitor ............................................... 116
Confirming the version of the camera ........................... 118
Resetting to the default .................................................. 119
Copying images to your computer ................................ 121
Viewing images on your computer ................................ 125
Using the software ......................................................... 129
Specifying DPOF ........................................................... 135
Printing images by connecting the camera to a PictBridge
compliant printer ...................................................... 137
Specifications ................................................................ 140
Troubleshooting ............................................................. 144
Warning messages ......................................................... 153
Precautions .................................................................... 156
Index .............................................................................. 158
10
Preparing the camera
Checking the accessories supplied
The number in parentheses indicates the number of pieces.
• BC-VH1 Battery charger (1)
• Power cord (mains lead) (1) (not
supplied in the U.S.A. and
Canada)
• Rechargeable battery pack NPFH50 (1)
• USB cable (1)
• Shoulder strap (1)
• Eyepiece cover (1)
• Body cap (1) (Attached on the
camera)
• Eyecup (1) (Attached on the
camera)
• CD-ROM (Application Software
for α camera) (1)
• Quick Start Guide (1)
• Instruction Manual (This manual)
(1)
Preparing the camera
11
Preparing the battery pack
When using the camera for the first time, be sure to charge the NP-FH50
“InfoLITHIUM” battery pack (supplied).
Charging the battery pack
The “InfoLITHIUM” battery pack can be charged even when it has not
been fully depleted.
It can also be used when it has not been fully charged.
1 Insert the battery pack on the
battery charger.
Push the battery pack until it clicks.
12
2 Connect the battery charger to the
wall outlet (wall socket).
Light on: Charging
Light off: Normal charge completed
One hour after the lamp is turned off: Full
charge completed
For customers in the U.S.A. and
Canada
Plug
To the wall
outlet (wall
socket)
CHARGE lamp
For customers in countries/regions
other than the U.S.A. and Canada
Power cord
(mains lead)
CHARGE lamp
About charging time
• Time required to charge a fully depleted battery pack (supplied) at a
temperature of 25°C (77°F) is as follows.
Full charge Normal charge
Approx. 265 min. Approx. 205 min.
• The charging time differs depending on the remaining capacity of the
battery back or charging conditions.
Preparing the camera
When the CHARGE lamp flashes
• The CHARGE lamp of the supplied battery charger flashes in either way:
– Fast flashing: Turns the light on and off repeatedly at the interval of
0.15 seconds.
– Slow flashing: Turns the light on and off repeatedly at the interval of
1.5 seconds.
13
• When the CHARGE lamp flashes fast, remove the battery pack being
charged, and then insert the same battery pack into the battery charger
securely again. When the CHARGE lamp flashes fast again, this may
indicate a battery error or that a battery pack other than the specified type
has been inserted. Check that the battery pack is the specified type. If the
battery pack is the specified type, remove the battery pack, replace it with
a new one or another one and check if the battery charger operates
correctly. If the battery charger operates correctly, a battery error may
have occurred.
• When the CHARGE lamp flashes slowly, it indicates that the battery
charger stops charging temporarily on standby. The battery charger stops
charging and enters the standby status automatically when the
temperature is outside of the recommended operating temperature. When
the temperature gets back within the appropriate range, the battery
charger resumes charging and the CHARGE lamp lights up again. We
recommend charging the battery pack in an ambient temperature of
between 10°C to 30°C (50°F to 86°F).
Notes
• Connect the battery charger to the nearest wall outlet (wall socket).
• When charging is finished, disconnect the power cord (mains lead) from the wall
outlet (wall socket), and remove the battery pack from the battery charger. If you
leave the charged battery pack on the charger, battery life may be decreased.
• Do not charge any battery pack other than the “InfoLITHIUM” H series battery pack
in the battery charger (supplied) with your camera. Batteries other than the specified
kind may leak, overheat, or explode if you attempt to charge them, posing a risk of
injury from electrocution and burns.
• If the battery charger is dirty, charging may not be performed successfully. Clean the
battery charger with dry cloth, etc.
To use your camera abroad — Power sources
You can use your camera and the battery charger and the AC-PW10AM
AC Adaptor (sold separately) in any country or region where the power
supply is within 100 V to 240 V AC, 50/60 Hz.
Note
• Do not use an electronic transformer (travel converter), as this may cause a
malfunction.
14
Inserting the charged battery pack
1 While sliding the battery cover
open lever, open the battery
cover.
2 Firmly insert the battery pack all
the way while pressing the lock
lever with the tip of the battery.
3 Close the battery cover.
To remove the battery pack
Turn off the camera and slide the lock
lever in the direction of the arrow. Be
careful not to drop the battery pack.
Preparing the camera
Lock lever
Lock lever
15
To check the remaining battery level
Set the power switch to ON and check the level on the LCD monitor.
“Battery
Battery level
High Low
exhausted”
You cannot shoot
any more pictures.
What is an “InfoLITHIUM” battery pack?
An “InfoLITHIUM” battery pack is a lithium-ion battery pack that has
functions for exchanging information related to operating conditions with
your camera.
Notes
• The displayed level may not be correct under certain circumstances.
• Do not expose the battery pack to water. The battery pack is not water-resistant.
• Do not leave the battery pack in extremely hot places, such as in a car or under direct
sunlight.
Available battery packs
Only an NP-FH50 battery pack can be used with the camera. Note that the
NP-FH30 and NP-FH40 cannot be used.
Effective use of the battery pack
• Battery performance decreases in low temperature surroundings. So, the
time that the battery pack can be used is shorter in cold places and the
speed of continuous shooting slows down. We recommend that you put
the battery pack in a pocket close to your body to warm it up, and insert it
in your camera immediately before you start shooting.
• The battery pack will run out quickly if you use the flash frequently, use
continuous shooting often, or turn the camera on and off frequently.
Battery life
• The battery life is limited. Battery capacity decreases little by little as you
use it more and more, and as time passes. If the battery operating time
seems shortened considerably, a probable cause is that the battery pack
has reached the end of its life. Buy a new battery pack.
• The battery life varies according to how it is stored and the operating
conditions and environment in which each battery pack is used.
16
How to store the battery pack
If the battery pack is not to be used for a long time, fully charge it and then
fully use it up once a year on your camera before storing the battery pack in
a dry, cool place to prolong the battery life.
Preparing the camera
17
Attaching a lens
1 Remove the body cap from the
camera and the packaging lid
from the rear of the lens.
• When changing the lens, quickly
change the lens away from dusty
locations so as to keep dust or debris
from getting inside the camera.
Packaging lid
2 Mount the lens by aligning the
orange index marks on the lens
and camera.
3 Turn the lens clockwise until it
clicks into the locked position.
Notes
• A rear lens cap is not supplied with the DT 18-55mm F3.5-5.6 SAM Lens Kit. When
you store the lens without attaching it to the camera, purchase the Rear Lens Cap
ALC-R55.
• When attaching a lens, do not press the lens release button.
• Do not use force when attaching a lens.
Body cap
Orange index marks
18
To remove the lens
1 Press the lens release button all
the way in and turn the lens
counterclockwise until it stops.
Lens release button
2 Replace the packaging lid on the
lens and attach the body cap to
the camera.
• Before you attach them, remove dust
from them.
• When you purchase the DT 18 – 55 mm
F3.5 – 5.6 SAM Lens Kit, purchase the
Rear Lens Cap ALC-R55 also.
Note on changing the lens
When changing the lens, if dust or debris gets inside the camera and lands
on the surface of the image sensor (the part that acts as the film), it may
appear on the image, depending on the shooting environment.
The camera is equipped with an anti-dust function to prevent dust from
landing on the image sensor. However, quickly change the lens away from
dusty locations when attaching/removing a lens.
If dust or debris lands on the image sensor
Clean the image sensor using [Cleaning mode] in the Setup menu
(page 30).
Preparing the camera
19
Inserting a memory card
Only “Memory Stick PRO Duo” media, “Memory Stick PRO-HG Duo”
media, SD memory cards and SDHC memory cards can be used with this
camera. A MultiMediaCard cannot be used with this camera.
The “Memory Stick PRO Duo” media and “Memory Stick PRO-HG Duo”
media are referred to as the “Memory Stick PRO Duo” media and the SD
memory card and SDHC memory card are referred to as the “SD memory
card” in this Instruction Manual.
1 Open the memory card cover.
2 Insert “Memory Stick PRO Duo”
media or an SD memory card.
• Insert the memory card until it clicks as
illustrated.
3 Select the type of memory card
you want to use using the memory
card switch.
20
Face side (SD memory card)
Terminal part
Face side (“Memory Stick PRO
Duo”)
Terminal part
4 Close the memory card cover.
To remove the memory card
Check that the access lamp is not lit, then
open the memory card cover, and push
the memory card once.
Access lamp
Notes on using memory cards
• Do not strike, bend or drop the memory card.
• Do not use or store the memory card under the following conditions:
– High temperature locations such as the hot interior of a car parked in
direct sunlight.
– Locations exposed to direct sunlight.
– Humid locations or locations with corrosive substances present.
• The memory card may be hot just after it has been used for a long time.
Be careful when you handle it.
• When the access lamp is lit, do not remove the memory card or the
battery pack, or turn off the power. The data may be corrupted.
• Data may be damaged if you place the memory card near stronglymagnetized material or use the memory card in a static-prone or
electrically noisy environment.
• We recommend backing up important data, such as to a hard disk of a
computer.
• When you carry or store the memory card, put it in the case supplied with
it.
• Do not expose the memory card to water.
• Do not touch the terminal section of the memory card with your hand or a
metal object.
• When the write-protect switch of a memory card is set to the LOCK
position, you cannot perform operations, such as recording or deleting
images.
21
Preparing the camera
• The “Memory Stick PRO Duo” media with a capacity up to 16 GB or the
SD memory cards with a capacity up to 32 GB have been confirmed to
operate properly with this camera.
• The memory cards formatted with a computer are not guaranteed to
operate with this camera.
• Data read/write speeds differ depending on the combination of the
memory cards and the equipment used.
• Do not press down hard when you write down on the memo area.
• Do not attach a label on the memory cards themselves.
• Do not disassemble or modify the memory cards.
• Do not leave the memory cards within the reach of small children. They
might accidentally swallow it.
Notes on the “Memory Stick” media used with the camera
The types of “Memory Stick” media that can be used with this camera are
listed in the table below. However, proper operation cannot be guaranteed
for all “Memory Stick PRO Duo” media functions.
“Memory Stick PRO Duo”
media*
“Memory Stick PRO-HG Duo”
media*
“Memory Stick Duo” media Unavailable with your camera
Available with your camera
“Memory Stick” media and
“Memory Stick PRO” media
* This is equipped with MagicGate function. MagicGate is copyright protection
technology that uses encryption technology. Data recording/playback that requires
MagicGate functions cannot be performed with this camera.
* Supports high-speed data transfer using a parallel interface.
Unavailable with your camera
22
Preparing the camera
Setting up the date
When you turn the camera on for the first time, the date/time setup screen
appears.
1 Set the power switch to ON to turn
the camera on.
• To turn the camera off, set it to OFF.
2 Verify that [OK] is selected on the
LCD monitor, then press the
center of the control button.
3 Select each item with b/B and
set the numeric value with v/V.
• When changing the sequence of
[YYYY/MM/DD], first select [YYYY/
MM/DD] with b/B, then change it
with v/V.
Preparing the camera
4 Repeat step 3 to set other items, then press the center of the
control button.
23
5 Verify that [OK] is selected, then press the center of the control
button.
To cancel the date/time setting operation
Press the MENU button.
To set up the date/time again
MENU button t 2 t [Date/Time setup]
Adjusting the focus of the finder (diopter adjustment)
Adjust the diopter-adjustment dial
to your eyesight until the indicators
appear clearly in the viewfinder.
• Turn the dial toward + when you are farsighted, toward – when you are near-sighted.
• Training the camera on a light allows you to
adjust the diopter easily.
When it is hard to rotate the diopter-adjustment dial
Put your fingers under the eyecup, and
slide it upward to remove the eyecup,
then adjust the diopter.
• When attaching the FDA-M1AM Magnifier
(sold separately) or the FDA-A1AM Angle
Finder (sold separately) to the camera,
remove the eyecup as illustrated and attach
them.
24
Using the accessories supplied
This section describes how to use the shoulder strap, the eyepiece cover,
and eyecup. The other accessories are described in the following pages.
• Rechargeable battery pack (page 12)
• Battery charger (page 12)
• Power cord (mains lead) (not supplied in the U.S.A. and Canada)
(page 12)
• USB cable (pages 122, 138)
•CD-ROM (page130)
Attaching the shoulder strap
Attach both ends of the strap onto
the camera.
• You can also attach the eyepiece cover
(page 26) on the strap.
Eyepiece cover
Preparing the camera
25
Using the eyepiece cover and eyecup
You can prevent light from entering through the viewfinder and affecting
the exposure. When the shutter is released without the use of the
viewfinder, as in shooting with the self-timer, attach the eyepiece cover.
1 Carefully slide the eyecup off by
pushing on each side of the
eyecup.
• Put your fingers under the eyecup, and
slide it upward.
2 Slide the eyepiece cover over the
viewfinder.
Note
• The eyepiece sensors located below the viewfinder may be activated depending on
the situation, and the focus may be adjusted or the LCD monitor may continue to
flash. In such cases, turn off both [Eye-Start AF] (page 71) and [Auto off w/ VF]
(page 117).
26
Checking the number of recordable images
Once you insert a memory card into the
camera and set the power switch to ON,
the number of images that can be
recorded (should you continue to shoot
using the current settings) is displayed on
the LCD monitor.
Notes
• When “0” (the number of recordable images) flashes in yellow, the memory card is
full. Replace the memory card with another one, or delete images in the current
memory card (page 102).
• When “NO CARD” (the number of recordable images) flashes in yellow, it means
no memory card has been inserted. Insert a memory card.
The number of images that can be recorded on a memory
card
The table shows the approximate number of images that can be recorded on
a memory card formatted with this camera. The values are defined using
Sony standard memory cards for testing. The values may vary depending
on the shooting conditions.
Image size: L 10M
Aspect ratio: 3:2*
“Memory Stick PRO Duo” media (Units: Images)
Capacity
Size
Standard 320 647 1281 2575 5221
Fine 237 480 951 1910 3874
RAW & JPEG 48 98 195 392 797
RAW 60 123 245 494 1004
1GB 2GB 4GB 8GB 16GB
Preparing the camera
27
SD memory card (Units: Images)
Capacity
Size
Standard 319 634 1277 2571 5221
Fine 236 470 947 1908 3874
RAW & JPEG 47 96 194 392 797
RAW 60 121 245 494 1004
* When [Aspect ratio] is set to [16:9], you can record more images than the numbers
shown in the table above. However, if it is set to [RAW], the number is the same as
that of the [3:2] aspect ratio.
1GB 2GB 4GB 8GB 16GB
The number of images that can be recorded using a battery
pack
The approximate number of images that can be recorded is 510 when you
use the camera with the battery pack (supplied) at full capacity.
Note that the actual numbers may be less than those indicated depending on
the conditions of use.
• The number is calculated with a battery pack at full capacity and in the
following situation:
– At an ambient temperature of 25°C (77°F).
– [Quality] is set to [Fine].
– [Autofocus mode] is set to (Automatic AF).
– Shooting once every 30 seconds.
– The flash strobes once every two times.
– The power turns on and off once every ten times.
• The measurement method is based on the CIPA standard.
(CIPA: Camera & Imaging Products Association)
28
Cleaning
Cleaning the LCD monitor
Wipe the screen surface with a commercially available LCD cleaning kit to
remove fingerprints, dust, etc.
Cleaning the lens
• When cleaning the lens surface, remove dust using a commercially
available blower. In case of dust that sticks to the surface, wipe it off with
a soft cloth or tissue paper slightly moistened with lens cleaning solution.
Wipe in a spiral pattern from the center to the outside. Do not spray lens
cleaning solution directly onto the lens surface.
• Do not touch the inside of the camera, such as lens contacts, or the mirror.
Since dust on the mirror or around the mirror may affect the autofocus
system, blow away dust using a commercially available blower. If dust
lands on the image sensor, it may appear on the photo image. Turn the
camera to the cleaning mode, then clean it using a blower (page 30). Do
not use a spray blower to clean the inside of the camera. Using this may
cause a malfunction.
• Do not use a cleaning solution containing organic solvents, such as
thinner, or benzine.
Cleaning the camera surface
Clean the camera surface with a soft cloth slightly moistened with water,
then wipe the surface with a dry cloth. Do not use the following as they
may damage the finish or the casing.
• Chemical products such as thinner, benzine, alcohol, disposable cloths,
insect repellent, sunscreen or insecticide, etc.
• Do not touch the camera with the above on your hand.
• Do not leave the camera in contact with rubber or vinyl for a long time.
Preparing the camera
29
Cleaning the image sensor
If dust or debris enters the camera and lands on the image sensor (the part
that acts as the film), it may appear on the photo image, depending on the
shooting environment. If there is dust on the image sensor, use a
commercially available blower and clean the image sensor following the
steps below. You can easily clean the image sensor using only the blower
and the anti-dust function.
Notes
• Cleaning can be performed only when the battery level is (three remaining
battery icons) or more. Low battery power during cleaning can cause damage to the
shutter. The cleaning should be completed quickly. The use of an AC-PW10AM AC
Adaptor (sold separately) is recommended.
• Do not use a spray blower because it may scatter water droplets inside the camera
body.
1 Confirm that the battery is fully charged (page 16).
2 Press the MENU button, then
select 3 with b/B on the
control button.
MENU button
3 Select [Cleaning mode] with v/V,
then press the center of the
control button.
The message “After cleaning, turn
camera off. Continue?” appears.
4 Select [OK] with v on the control button, and press the center
of the control button.
After the image sensor vibrates for a short time, the mirror in front is lifted.
30
Loading...