Sony DRBT1, DRCBT1 User Manual

2-186-671-11(1)

Bluetooth® Earset System

Getting started

Unpacking

Check that you have the following items:

• Bluetooth earset (1)

Charging the units

The Bluetooth earset contains a rechargeable LithiumIon battery and the Bluetooth earset adaptor contains a Nickel-Metal Hydride battery, which should be charged before using for the first time.

1 Dock the Bluetooth earset with the

Bluetooth earset adaptor.

Operating Instructions Manual de instrucciones

DR-BT1K

THIS PRODUCT IS MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING SONY U.S. PATENTS: 4,429,194; 4,736,435; 4,668,842; AND OTHER PATENTS ISSUED OR PENDING IN U.S. AND OTHER COUNTRIES

English

Owner’s Record

The model and serial number are located at the rear of the Bluetooth earset and at the belt clip of the Bluetooth earset adaptor. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. DR-BT1K

Bluetooth earset : DR-BT1 Bluetooth earset adaptor : DRC-BT1

Serial No.

Bluetooth earset: Bluetooth earset adaptor:

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Note :

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and

receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/ TV

technician for help.

------------------------

------------------

For the customers in the USA

– Recycling of battery in Bluetooth earset

RECYCLING LITHIUM-ION BATTERIES

Lithium-Ion batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you.

For more information regarding recycling of rechargeable batteries, call toll free 1-800-822-8837, or visit http://www.rbrc.org/

Caution: Do not handle damaged or leaking Lithium-Ion batteries.

–Recycling of battery in Bluetooth earset adaptor

RECYCLING NICKEL METAL HYDRIDE BATTERIES

Nickel Metal Hydride batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you.

For more information regarding recycling of rechargeable batteries, call toll free 1-800-822-8837, or visit http://www.rbrc.org/

Caution: Do not handle damaged or leaking Nickel Metal Hydride batteries.

Welcome!

Thank you for purchasing the Sony DR-BT1K Bluetooth earset system. Before operating the unit, please read this manual thoroughly and retain it for future reference. Some features are:

•Wireless system that allows you to talk by mobile phone.

• Car Air-vent clip for car use.

•Fits on either your right or left ear.

• Convenient earset adaptor with belt clip

• Up to 5 hours for talking. Up to 100hours for standby.

• Flexible pipe microphone.

•Volume control function on the earset.

What's Bluetooth?

Bluetooth is a new technology that enables wireless data communication by mobile phones, computers or other mobile devices. Bluetooth wireless technology operates within a range of about 10 meters* (about 30 feet). * Obstacles (body, metal, wall etc.) or reception

conditions may adversely affect the usable range.

• Hanger (Size S) (1)

• Bluetooth earset adaptor (1)

•AC power adaptor (1)

• Car Air-vent clip (1)

•Warranty (1)

• Operating Instructions (1)

Identifying

Bluetooth earset

1 Hanger 2 Multifunction button

Controls various functions of the Bluetooth earset.

3 LED indicator

Indicates the status of the Bluetooth earset.

4 VOLUME + 5 VOLUME - 6 Pipe microphone 7 Housing 8 Contact terminal

Bluetooth earset adaptor

1 LED indicator

Indicates the status of the Bluetooth earset adaptor.

2 Power on button 3 Pairing / Power off button 4 Contact pin 5 Belt clip 6 DC IN 4.5 V jack

2 Connect the supplied AC power

adaptor to DC IN 4.5 V jack on the Bluetooth earset adaptor.

When the AC power adaptor connected to an AC outlet, both units will turn off automatically.

To an AC outlet

AC power adaptor (supplied)

To DC IN 4.5 jack

3 Make sure that the indicator lights up

green.

Charging is completed in about 2.5 hours* and the indicator goes off.

Both indicators light up green

*Time required to fully charge empty battery.

Notes

• Charge in an environmental temperature of between 0˚C and 40˚C (between 32˚F and 104˚F).

•Avoid exposure to temperature extremes, direct sunlight, moisture, sand, dust or mechanical shock. Never leave in a car parked in the sun.

• Use only the supplied AC power adaptor. Do not use any other AC power adaptor.

Polarity of the plug

Recommended accessory

Car Multi-Voltage DC Adaptor : DCC-E345 Buy Sony Accessories at URL : http://www.sony.com/sonyaccessories or call 1-888-559-7669 (SONY)

Charging and usage hours

It is usage time from fully charged.

Bluetooth Bluetooth earset earset adaptor <DR-BT1> <DRC-BT1>

Talk time 7 hours 5 hours (up to)

Standby time 160 hours 100 hours (up to)

Time stated above may vary, depending on the temperature or conditions of use.

Note

Charge the built-in rechargeable battery or if the LED indicator is still off after charging the built-in rechargeable battery, take the Bluetooth earset and Bluetooth earset adaptor to a Sony dealer for replacement of the rechargeable battery.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has very low levels of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR).

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by SONY is under license. Nokia is a registered trademark of Nokia Corporation.

Notes

• The communication with Bluetooth wireless technology may be affected by the conditions below.

– Obstacles between the Bluetooth earset and the

Bluetooth earset adaptor or mobile phones with Bluetooth wireless technology : Body, metal, walls, etc.

– Electromagnetic waves

: A place where a wireless LAN is installed, a microwave oven is used, or where electromagnetic energy exists

•The above is also subject to the mobile phone’s antenna and reception conditions.

Pairing the units

To pair Bluetooth earset with Bluetooth earset adaptor

The Bluetooth earset and Bluetooth earset adaptor come already paired from factory. To pair the Bluetooth earset and Bluetooth earset adaptor again after use, do the following.

1 Place the Bluetooth earset and the

Bluetooth earset adaptor close together, as illustrated.

1m*

2 While the Bluetooth earset is turned

off, hold down the Maltifunction button.

The LED will blink in blue for the first 7 seconds (approx.). Keep pressing until the LED blinks blue and green.

Operating the system

Wearing the headset

1 Hook the Bluetooth earset around

your ear, as you would glasses.

2 Adjust the position of the Bluetooth

earset to fit comfortably.

Changing the direction of the hanger

This unit can be worn on the right or left ear by the following procedure.

1 Holding the housing firmly, unlatch

the hanger assembly.

Operating the units

General operation flow is described as follows:

To change into a standby mode

To shut down the units

D To call

Take the calling, finish the talking or dial by operating the mobile phone.

If your mobile phone equipped with voice-dial function, you can dial by the pipe microphone.

E To discommunicate of the units

Press the Multifunction button once.

SCO LINK disconnects. The Bluetooth earset and the Bluetooth earset adaptor return to the standby mode.

To shut down the units

To shut down the Bluetooth earset

Hold down the POWER/TALK button on the Bluetooth earset until LED turned off.

3 Press the Power on button on the

Bluetooth earset adaptor.

4 Hold down the Pairing / Power off

button with the point of the plug or similar instrument (for about 3 seconds) until the LED lights up blue and green.

After a few seconds, both units the blue/green blinking will change to blink only blue, indicating Standby mode.

Note

Time out for pairing mode is as follows: The Bluetooth earset : about 60 seconds. The Bluetooth earset adaptor : about 20 seconds.

To pair Bluetooth earset with a mobile phone for Bluetooth wireless technology

The Bluetooth earset can pair directly a mobile phone with Bluetooth wireless technology. Do the following.

1 Place the Bluetooth earset and the

mobile phone close together within 1 m.

2 Repeat above step 2.

See “To pair Bluetooth earset with Bluetooth earset adaptor”.

3 Search the Bluetooth earset by the

mobile phone.

If the mobile phone detects the Bluetooth earset, “DR-BT1” will appear in the display of the mobile phone.

4 Select “DR-BT1” in the list, then input

the passkey* (0000).

After a few seconds, the setting is completed.

*Passkey may also be called the following.

– Pass code, PIN code, PIN number, Password.

Note

Refer to the manual supplied with your mobile phone.

2 Holding the housing, rotate the

hanger, and then pull out in the direction of the arrow.

Tip

The unit comes with 2 hanger sizes to ensure a comfortable fit.

3 Turn the hanger around as illustrated

below, and attach in the direction of the arrow.

4 Rotate the housing.

The mobile phone provided function may not correspond. Refer to the manual supplied with your mobile pone.

To change into a standby mode

A To prepare the Bluetooth earset

Hold down the Multifunction button on the Bluetooth earset about 7 seconds.

When the LED blinks fast blue, release the button. The LED becomes to blink slowly blue.

Note

Take care that if the Maltifunction button hold down about 10 seconds, the status goes pairing mode.

B To prepare the Bluetooth earset

adaptor

1 Press the POWER ON button a few

seconds.

When the LED lights up blue and green, after the LED becomes to blink slowly blue.

2 Connect the Bluetooth earset adaptor

to your mobile phone.

2.5 mm tripe polarity jack

If there are not obstacles between the Bluetooth earset and the Bluetooth earset adaptor, the communication sensitivity goes up.

C To communicate of the units

(SCO LINK)

Press the Multifunction button.

The Bluetooth earset and the Bluetooth earset adaptor start communication (SCO LINK), so that the sound from mobile phone is heard by the Bluetooth earset. And the voice talking by the pipe microphone is transmitted to the mobile phone.

G To shut down the Bluetooth

earset adaptor

Hold down the Pairing/Power off button with the point of the plug or similar instrument until LED turned off.

When the telephone is received

Press your mobile phone buttons.

There is a mobile phone that can receive pressing the POWER/TALK button.

To adjust the volume

Press the VOLUME + or – while SCO Link.

The beep of current volume is heard every time by pressing each button. When the volume setting is maximum or minimum, the beep does not sound for the exceeded operations.

VOLUME + VOLUME -

How to use the car attachment

The car attachment (supplied) can be used hold the Bluetooth earset adaptor, by installing it in the vent of the air conditioner of your car. It is convenient for charging/using while driving.

Standard installation

Horizontal fin

17 mm (min)

3 mm (min)

Vertical fin

3 mm (min)

7 mm (min)

9 mm (min)

7 mm (min)

9 mm (min)

Note

The housing and the hanger are marked left (L) and right (R). For example, when using the left ear, the housing is set in the L position, and the hanger is attached with the L mark visible.

When the SCO LINK has been started, the LED on Bluetooth earset adaptor lights up green, then that blinks blue. The LED on Bluetooth earset blinks 3 times blue.

17 mm (min)

+ 1 hidden pages