SONY DPP-MS300, DK1830SI, DR400, DR6, W300 Service Manual

HCD-DR4/DR5/DR6/DR440/
W300/W5000/XB500
SERVICE MANUAL
HCD-DR4/DR5/DR6/DR440/W300/W5000/ XB500 is the tuner, deck, CD and amplifier section in LBT -DR4/DR5/DR6/DR440/W300/ W5000/XB500.
Photo: HCD-DR6
CD
SECTION
TAPE DECK
SECTION
Model Name Using Similar Mechanism HCD-D290/G3300/XB3 CD Mechanism Type CDM37M-5BD32L Base Unit Type BU-5BD32L Optical Pick-up Type KSS-213D/Q-N Model Name Using Similar Mechanism NEW T ape Transport Mechanism T ype TCM-230AWR2/230PWR2
US Model
HCD-W300/W5000
Canadian Model
HCD-W300
AEP Model
UK Model
E Model
HCD-DR4/DR5/DR6/DR440
Australian Model
HCD-DR4
SPECIFICATIONS
— Continued on next page —
MICROFILM
COMPACT DISC DECK RECEIVER
– 1 –
– 2 –
CAUTION
0.15µF
To Exposed Metal Parts on Set
1.5k
AC voltmeter (0.75V)
Earth Ground
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous ra­diation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PROD­UCT MARKING is located on the rear exterior.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow­ing safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for A C leakage. Check leakage as described below.
LEAKAGE
The AC leakage from any exposed metal part to earth Ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leak­age current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments.
2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a V OM or battery-operated A C v oltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a pas­sive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)
This caution label is located inside the unit.
Fig. A. Using an AC voltmeter to check AC leakage.
COMPONENTS IDENTIFIED BY MARK ! OR DO TTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
SAFETY-RELATED COMPONENT WARNING !!
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS P AR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT . NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
– 3 –
MODEL IDENTIFICATION — BACK PANEL —
Parts No.
MODEL PRODUCT COUNTRY PARTS No.
DR4: E, AR model INDONESIA PRODUCT 4-214-786-0π DR4: TH model THAI PRODUCT 4-214-786-9π DR4: SP model INDONESIA PRODUCT 4-214-786-1π DR4: MX model INDONESIA PRODUCT 4-214-786-2π DR4: AUS model INDONESIA PRODUCT 4-214-786-3π DR4: EA model INDONESIA PRODUCT 4-214-786-4π DR5: E, AR model INDONESIA PRODUCT 4-214-786-5π DR5: SP model INDONESIA PRODUCT 4-214-786-6π DR5: MX model INDONESIA PRODUCT 4-214-786-7π DR440: MX model INDONESIA PRODUCT 4-214-786-8π W300: US model INDONESIA PRODUCT 4-214-787-4π W300: CND model INDONESIA PRODUCT 4-214-787-5π W5000: US model INDONESIA PRODUCT 4-214-787-6π DR6: E, AR model INDONESIA PRODUCT 4-214-788-3π DR6: MX model INDONESIA PRODUCT 4-214-788-5π XB500: AEP, UK model INDONESIA PRODUCT 4-214-785-0π XB500: AEP model THAI PRODUCT 4-214-785-2π
• Abbreviation CND : Canadian model TH : Thailand model SP : Singapore model MX : Mexican model AUS : Australian model EA : Saudi Arabia model AR : Argentine model
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick­up block. Therefore, when checking the laser diode emission, ob­serve from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION CHECK
Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveform is output four times.
SECTION 1

SERVICING NOTE

About CD-TEXT display
This unit is provided with a simple CD-TEXT display function. The CD-TEXT contents of 20 tracks are displayed on the fluores­cent display tube. Since the function is simple, some special characters may not be displayed, or may be displayed as other characters.
– 4 –
TABLE OF CONTENTS
1. SERVICING NOTE .......................................................... 4
2. GENERAL ....................................................................6
2. DISASSEMBLY
3-1. Front Panel ............................................................................ 8
3-2. Main Board ........................................................................... 8
3-3. Sub Panel .............................................................................. 9
3-4. CD-L/CD-R Board and CD LID Assembly .......................... 9
3-5. Tape Mechanism Deck and Cassette LID...........................10
3-6. CD Mechanism Deck .......................................................... 10
3-7. Base Unit.............................................................................10
3-8. Disc Table ........................................................................... 11
4. SERVICE MODE ............................................................ 12
5. MECHANICAL ADJUSTMENTS ..........................16
6. ELECTRICAL ADJUSTMENTS ...............................16
7. DIAGRAMS
7-1. Circuit Boards Location ...................................................... 20
7-2. Block Diagrams
• BD (CD) Section.............................................................. 21
• Deck Section .................................................................... 23
• Main (1/2) Section ........................................................... 25
• Main (2/2) Section ........................................................... 27
• Power Section (DR4, DR5, DR6, DR440 model) ........... 29
• Power Section (W300, W5000, XB500 model)............... 31
• Display Section ................................................................ 33
7-3. Printed Wiring Board – BD (CD) Section – ....................... 37
7-4. Schematic Diagram – BD (CD) Section – .......................... 39
7-5. Printed Wiring Board – Main Section – .............................. 41
7-6. Schematic Diagram – Main (1/5) Section – ........................ 43
7-7. Schematic Diagram – Main (2/5) Section – ........................ 45
7-8. Schematic Diagram – Main (3/5) Section – ........................ 47
7-9. Schematic Diagram – Main (4/5) Section – ........................ 49
7-10. Schematic Diagram – Main (5/5) Section – ..................... 51
7-11. Schematic Diagram – Deck Section – .............................. 53
7-12. Printed Wiring Board – Deck Section – ........................... 55
7-13. Schematic Diagram – Power (1/2) Section –
(DR4, DR5, DR6, DR440 model) .................................... 57
7-14. Schematic Diagram – Power (2/2) Section –
(DR4, DR5, DR6, DR440 model) .................................... 59
7-15. Printed Wiring Board – Power Section –
(DR4, DR5, DR6, DR440 model) .................................... 61
7-16. Schematic Diagram – Power (1/2) Section –
(W300, W5000, XB500 model) ....................................... 63
7-17. Schematic Diagram – Power (2/2) Section –
(W300, W5000, XB500 model) ....................................... 65
7-18. Printed Wiring Board – Power Section –
(W300, W5000, XB500 model) ....................................... 67
7-19. Schematic Diagram – Panel FL Section – ........................ 69
7-20. Printed Wiring Board – Panel FL Section – ..................... 71
7-21. Schematic Diagram – Panel VR Section – ....................... 73
7-22. Printed Wiring Board – Panel VR Section – ....................75
7-23. Schematic Diagram – TC Panel Section – ....................... 77
7-24. Printed Wiring Board – TC Panel Section –..................... 79
7-25. Schematic Diagram – CD Panel Section – ....................... 81
7-26. Printed Wiring Board – CD Panel Section – .................... 83
7-27. Schematic Diagram – CD Motor Section – ...................... 85
7-28. Printed Wiring Board – CD Motor Section –...................87
7-29. Schematic Diagram – Jack Section – ............................... 89
7-30. Printed Wiring Board – Jack Section – ............................ 91
7-31. Schematic Diagram – Trans Section –
(W300, W5000, XB500 model) ....................................... 93
7-32. Printed Wiring Board – Trans Section –
(W300, W5000, XB500 model) ....................................... 95
7-33. Schematic Diagram – Trans Section –
(DR4, DR5, DR6, DR440 model) .................................... 97
7-34. Printed Wiring Board – Trans Section –
(DR4, DR5, DR6, DR440 model) .................................... 99
7-35. Schematic Diagram – Leaf SW Section – ...................... 100
7-36. Printed Wiring Board – Leaf SW Section – ................... 100
7-37. IC Block Diagrams ......................................................... 101
7-38. IC Pin Functions ............................................................. 102
8. EXPLODED VIEWS
8-1. Case and Back Panel Section ............................................ 105
8-2. Front Panel Section 1 ........................................................ 106
8-3. Front Panel Section 2 ........................................................ 107
8-4. Chassis Section ................................................................. 108
8-5. TC Mechanism Section 1 (TCM230AWR2/230PWR2)... 109 8-6. TC Mechanism Section 2 (TCM230AWR2/230PWR2)... 110
8-7. CD Mechanism Section (CDM37M-5BD32L).................111
8-8. Base Unit Section (BU-5BD32L) ..................................... 112
9. ELECTRICAL PARTS LIST ...................................... 113
– 5 –
Front Panel
SECTION 2

GENERAL

70 69
68 67
66
65
59 57
54
64
58 56
53
63
606162
55
10
2341
56
79
8
11 12
13 14 15 16 17
26 28
27
29
18
19
20 21
22
23 2425
30
31 32
33
34
52 51 50 49 48
47
35
37
36
39 40 41
42
43
44
4546
38
– 6 –
LOCATION OF PARTS AND CONTROLS
1 1/u (Power) button and indicator 2 DEMO (STANDBY) button
(DR4/DR5/DR6/DR440) POWER SAVE/DEMO (STANDBY) button (W300/W5000/XB500)
3 DISPLAY button 4 SPECTRUM ANALYZER button 5 Display window 6 GEQ control button 7 SYNC BASS button 8 SYNC EQ button 9 Remote sensor 10 PTY button (XB500) 11 TUNING MODE button 12 STEREO/MONO button 13 ENTER/NEXT button and indicator 14 TUNER MEMORY button 15 TUNER/BAND button 16 TUNING - button 17 TUNING + button 18 FUNCTION button 19 VOLUME knob 20 PHONES jack 21 MIC LEVEL knob 22 MIX MIC jack 23 GROOVE button and indicator
24 SUPER WOOFER button and indicator 25 MODE button 26 ª (B Deck) button and indicator 27 · (B Deck) button and indicator 28 p (B Deck) button 29 0 (B Deck) button 30 ) (B Deck) button 31 P (B Deck) button 32 r REC (B Deck) button 33 HI-SPEED DUB button 34 CD SYNCHRO button 35 PLAY MODE button 36 REPEAT button 37 0 (CD) button 38 ) (CD) button 39 ·P (CD) button and indicator 40 p (CD) button 41 DISK SKIP button 42 = AMS + knob 43 VIDEO2 INPUT jacks 44 EDIT button 45 NON-STOP button and indicator 46 LOOP button 47 FLASH button 48 DISC 5 button 49 DISC 4 button
50 DISC 3 button 51 DISC 2 button 52 DISC 1 button 53 DOLBY NR button 54 DIRECTION button 55 ) (A Deck) button 56 0 (A Deck) button 57 p (A Deck) button 58 · (A Deck) button 59 ª (A Deck) button 60 KARAOKE PON/MPX button 61 SURROUND button and indicator 62 EFFECT button and indicator 63 ENTER button and indicator 64 GEQ CONTROL button 65 P. FILE MEMORY 66 Equalizer indicators 67 t/CLOCK SET button 68 SLEEP button 69 REC button and indicator 70 DAILY button and indicator
• AMS is the abbreviation for Automatic Music Sensor.
This section is extracted from instruction manual.
– 7 –
SECTION 3
)

DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.
3-1. FRONT PANEL
3
Connector (CN452)
2
Connector (CN702)
1
Three flat type wires
(CN303,CN304,CN431)
4
7
Front panel
Connector (CN802)
3-2. MAIN BOARD
!∞
Back panel
Power cord
6
Screw (BVTP 3x8)
(HCD-W300/W5000/XB500)
Four screw (BVTP 3x8)
!™
Screw (BVTP 3x8)
(HCD-XB500)
2
Two screws (BVTP 3x8)
0
Two screws (BVTP 3x8)
(HCD-DR4/DR440/W300/W5000)
9
Three screws (BVTP 3x8)
0
Two screws (BVTP 3x8)
(HCD-DR5/DR6)
8
Two screws (BVTP 3x8)
7
Seven screws (BVTP 3x8)
5
Screw (BVTP 3x8
Main board
6
Connector (CN903)
(Except XB500)
1
Flat type wire (CN1)
Fan motor
(Except XB500)
5
Flat type wire (CN411)
4
Connector (CN412)
– 8 –
3
T uner unit
Two screws (BVTP 3x8)
3-3. SUB PANEL
5
Two screws (BTP 2.6x6)
4
Open the CD lid assembly
9
Sub panel block
6
Screw (BVTP 3x8)
8
Three screws (BVTP 2.6x8)
7
Two screws (BVTP 2.6x8)
1
Two screws (BVTP 2.6x8)
2
Screw (BVTP 3x8)
3
Front input board
3-4. CD-L/CD-R BOARD AND CD LID ASSEMBLY
1
Three screws (BVTP 2.6x8)
3
Bracket (CD-L)
4
CD-L board
2
Three screws
(BVTP 2.6x8)
Torsion spring (CD-L)
CD lid assembly
!™
Torsion spring (CD-L)
Sub panel assembly
5
Knob (CD)
6
Nut
0
CD-R board
Torsion spring (CD-R)
7
Three screws
(BVTP 2.6x8)
9
Bracket (CD-R)
8
Two screws (BVTP 2.6x8)
Sub panel assembly
CD lid assembly
– 9 –
3-5. TAPE MECHANISM DECK AND CASSETTE LID
t
5
Cassette lid (B) block
6
Cassette lid (A) block
Portion
2
Release
(Refer to order No.1)
B
Portion
1
A
Release
4
Torsion spring (TC-A)
Portion
A
7
Two screws (BVTP 2.6x8)
Portion
C
Portion
3
Torsion spring (TC-B)
Portion
B
A
Portion
8
Three screws
(BVTP 2.6x8)
9
T ape mechanism
C
3-6. CD MECHANISM DECK 3-7. BASE UNIT
1
Five screws (BVTP3x8)
2
CD mechanism
deck
2
Boss
3
Base uni
1
Yoke fitting
– 10 –
3-8. DISC TABLE
Note:
When the disc table is installed, adjust the positions of roller cam and mark as shown in the figure, then set to the groove of disc table.
A
2
Screw (BVTP3X8)
3
Bracket (BU)
1
Screw (BVTP3X8)
4
Stop screw
5
Disc table
A
– 11 –
SECTION 4

SERVICE MODE

MC Cold Reset
• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer.
Procedure:
1. Press three buttons t/CLOCK SET , ENTER , and 1/u simultaneously.
2. “COLD RESET” is displayed on the fluorescent display tube and reset is executed.
CD Delivery Mode
• This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.
Procedure:
1. Press 1/u button to turn the set ON.
2. Press LOOP button and 1/u button simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator tube, and the CD delivery mode is set.
MC Hot Reset
• This mode resets the set with the preset data kept stored in the memory . The hot reset mode functions same as if the po wer cord is plugged in and out.
Procedure:
1. Press three buttons t/CLOCK SET , ENTER , and DISC 1 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.
Sled Servo Mode
• This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up.
Procedure:
1. Press 1/u button to turn the set ON.
2. Press three buttons t/CLOCK SET , ENTER , and DISC 5 simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the fluorescent indicator tube.
4. With the CD in stop status, When the = AMS + knob is rotated in the clockwise direction, the pick-up moves outside. When
rotated counterclockwise, it moves inside.
5. To exit from this mode, perform as follows:
1) Move the pick-up to the most inside track.
2) Execute MC cold reset. (Press the three buttons t/CLOCK SET , ENTER , and 1/u button simultaneously.)
Note:
• Always move the pick-up to most inside track when exiting from this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be chipped.
Change-over of AM Tuner Step between 9kHz and 10kHz
• A step of AM channels can be changed over between 9kHz and 10kHz.
Procedure:
1. Press 1/u button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND button to select the BAND “AM”.
3. Press 1/u button to turn the set OFF.
4. Press ENTER and 1/u buttons simultaneously, and the display of fluorescent indicator tube changes to “AM 9k STEP” or “AM 10k
STEP”, and thus the channel step is changed over.
LED and Fluorescent Indicator Tube All Lit, Key Check Mode
Procedure:
1. Press three buttons t/CLOCK SET , ENTER , and DISC 2 simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
Press DISC 2 button, and the key check mode is activated.
3. In the key check mode, the fluorescent indicator tube displays “K @ V0 J0”. Each time a button is pressed , “K”value increases. Howe ver ,
once a button is pressed, it is no longer taken into account. “J” Value increases like 1, 2, 3 ... if rotating = AMS + knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction. “V” Value increases like 1, 2, 3 ... if rotating VOLUME knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
4. To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.
– 12 –
AMS Test Mode
• This mode is used for checking the AMS operations of the tape deck.
JIG 7-819-039-12 Alignment tape, AMS-110A
Procedure:
1. Press the 1/u button to turn the set ON.
2. Set the tape (AMS-110A).
3. Press the three buttons t/CLOCK SET , ENTER , and DISC 3 button simultaneously.
4. “TEST MODE” is displayed on the fluorescent display tube.
5. Press the FUNCTION button and switch the function to the deck with the tape (AMS-110A).
6. Press the CD SYNCHRO button. “AMS CHECK” is displayed on the fluorescent display tube and the tape is rewound.
7. AMS starts in the normal direction. If the AMS count is 2 at shut down, proceed to step 8. “NG” is displayed at other times, and the deck stops.
8. AMS starts in the opposite direction. If the AMS count is 2 at shut down again, “OK” is displayed. “NG” is displayed at other times.
Aging Mode
During the aging mode, both the CD player and tape deck are executed together.
• If an error occurs:
Aging stops, and the error state is displayed on the fluorescent display tube.
• If no error occurs:
Aging is repeated.
Procedure:
1. Press the 1/u button to turn the set ON.
2. Load 10 minute tapes with unbent rec-proof tabs in decks A and B.
3. Set CDs on the DISC 1 and DISC 4 tables.
4. Set the CD mode REPEAT to OFF and PLAY MODE to ALL DISCS. (Press the PLAY MODE and REPEAT buttons to set these modes.)
5. Press the FUNCTION button to switch the function to “CD”.
6. Press the three buttons t/CLOCK SET , ENTER , and DISC 4 button simultaneously.
7. Aging starts.
8. To end aging, press the 1/u button to turn the set OFF.
Aging Sequence:
Aging is performed in the following sequence.
• T ape Deck
1. The tape in deck A is rewound. “TAPE A AG-1” is displayed.
2. The FWD side of deck A is played for two minutes. “TAPE A AG-2” is displayed.
3. The tape in deck A is fast forwarded. “TAPE A AG-3” is displayed. Fast forward is carried out for 20 seconds or to the tape end.
4. The RVS side of deck A is played for two minutes. “TAPE A AG-4” is displayed.
5. The tape in deck A is rewound. “TAPE A AG-5” is displayed.
6. The FWD side of deck B is played for two minutes. “TAPE B AG-2” is displayed.
7. The tape in deck B is fast forwarded. “TAPE B AG-3” is displayed. Fast forward is carried out for 20 seconds or to the tape end.
8. The RVS side of deck B is played for two minutes. “TAPE B AG-4” is displayed.
9. The tape in deck A is rewound. “TAPE A AG-5” is displayed.
10. Repeated from step 2.
• CD
1. The tray rotates.
2. DISC 1 is chucked.
3. The TOC is read.
4. The first track is played for 2 seconds.
5. The last track is played for 2 seconds.
6. The tray rotates.
7. DISC 4 is chucked.
8. The TOC is read.
9. The first track is played for 2 seconds.
10. The last track is played for 2 seconds.
11. Repeated from step 1.
– 13 –
• Display when ended abnormally When the tape deck is abnormal:
The state when ended abnormally is displayed. The contents of display are the same as that during aging.
When the CD player is abnormal:
A message indicating that errors such as “CD MEC ERR” have occurred. Check the error contents in the following error history display mode.
Error History Display Mode
Mode which enables the history of error occurring in the CD player to be checked. Execute this mode after ending the aging mode.
Procedure:
1. Press the 1/u button to turn the set ON.
2. Press the three buttons t/CLOCK SET , ENTER , and CD SYNCHRO simultaneously.
3. A message such as “EMC@@EDC**” is displayed. @@ : Number of mechanical errors (Up to three past errors) ** : Number of errors (NO DISC ERROR) which occurs after chucking (Up to three past errors)
4. When checking the history of mec hanical errors, press the PLAY MODE button. When checking errors after chucking, press the REPEAT button to switch the display.
5. Press the 1/u button to end and turn the set OFF.
6. To erase the error history, perform COLD reset. (Press the three buttons t/CLOCK SET , ENTER , and DISC 1 simultaneously.
• Viewing the mechanical error history display
(Switch the history by pressing the PLAY MODE button.)
Display E@@M#*****
@@ : Error number. 00 is the newest.
# : Operating state of table
0 : Currently in the INITIAL mode 7 : Currently rotating to the right 8 : Currently rotating to the left A : Currently chucking down B : Currently chucking up
* : Invalid
– 14 –
• Viewing the NO DISC ERROR history display (Switch the history by pressing the REPEAT button.)
Display E@@D##$$%*
@@ : Error number. 00 is the newest
## : Error contents
01: Focus error 02: GFS error 03: Setup error
$$ : Retries
00: NO DISC is determined without attempting chucking retry 02: NO DISC is determined after chucking retry.
% : State when determined as NO DISC 1 : When stopped 2 : At setup 3 : At TOC READ 4 : When accessing 5 : When playing 6 : When pausing 7 : When manual searching (during play) 8 : When manual searching (during pausing) * : Invalid
– 15 –
SECTION 5

MECHANICAL ADJUSTMENTS

SECTION 6

ELECTRICAL ADJUSTMENTS

Precaution
1. Clean the following parts with a denatured alcohol-moistened swab:
record/playback heads pinch rollers erase head rubber belts capstan idlers
2. Demagnetize the record/playback head with a head demagne­tizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the parts adjusted.
5. The adjustments should be performed with the rated power sup­ply voltage unless otherwise noted.
Torque Measurement
Mode
FWD FWD
back tension REV
REV back tension
FF/REW
FWD tension
REV tension
Torque meter
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
Meter reading
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
71 to 143 g • cm
(0.98 – 1.99 oz • inch)
100 g or more
(3.53 oz or more)
100 g or more
(3.53 oz or more)
DECK SECTION 0 dB=0.775V
1. Demagnetize the record/playback head with a head damagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the parts adjusted.
4. The adjustments should be performed with the rated power sup­ply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjust­ment.)
6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwise specified.
Signal
P-4-A100
WS-48B
P-4-L300
10 kHz, –10 dB
3 kHz, 0 dB
315 Hz, 0 dB
Record/Playback Head Azimuth Adjustment (Deck A, Deck B)
Note: Perform this adjustments for both decks.
Procedure:
1. Mode : Playback
Used forTape
Azimuth Adjustment
Tape Speed Adjustment
Level Adjustment
test tape P-4-A100 (10kHz, –10dB)
set
MD OUT
level meter
+ –
2. Turn the adjustment scre w and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1 dB of peak.
L-CH peak
screw position
R-CH peak
output level
within 1 dB
L-CH peak
R-CH peak
within 1dB
screw position
– 16 –
3. Mode: Playback Tape Speed Adjustment (Deck A)
)
test tape P-4-A100 (10kHz, –10dB)
oscilloscope
MD OUT
Note: Set the test mode using the following method and begin tape
speed adjustment. In the test mode, the speed will switch to double speed or normal speed each time the HI-SPEED DUB button is pressed.
set
Waveform of oscilloscope
in phase 45
good
°
135
90
°
°
wrong
180
°
4. After the adjustments, apply suitable locking compound to the parts adjusted.
Adjustment Location: Playback Head (Deck A)
Record/Playback/Erase Head (Deck B)
Remove the cassette lid.
Procedure:
With the power turned ON, press the t/CLOCK SET button, ENTER button, and DISC 3 button simultaneously. (The “VOLUME” on the fluorescent display tube will blink while in the test mode.) To exit the test mode, press the 1/u button.
1. Insert the WS-48B into deck B.
2. Press the · button of deck B.
3. Press the HI-SPEED DUB button and play the tape at double speed.
4. Adjust RV1001 of the LEAF SW board so that the reading of the frequency counter becomes 6000 ± 180 Hz.
5. Press the HI-SPEED DUB button and play the tape at normal speed.
6. Adjust RV1002 of the LEAF SW board so that the reading of the frequency counter becomes 3000 ± 90 Hz.
Adjustment Location: LEAF SW board
Sample Value of Wow and flutter
W.RMS (JIS) less than 0.3% (test tape: WS-48B)
Playback Level Adjustment (Deck A, Deck B)
Procedure:
Mode: Playback
Reverse Foward
test tape P-4-L300 (315Hz, 0dB)
set
MD OUT
level meter
Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301 (L-CH) and RV401 (R-CH) so that adjustment within the following adjustment level.
Adjustment level:
CN301 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level difference between the channels: within ± 0.5 dB Adjustment Location: AUDIO board
Adjustment Location [LEAF SW BOARD]
RV1001(High Speed) RV1002(Normal Speed
RV1002 RV1001
– 17 –
Record Bias Adjustment (Deck B)
Record Level Adjustment (Deck B)
Procedure:
INTRODUCTION
When set to the test mode performed in Tape Speed Adjust­ment, when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is set. This “REC memory mode” is convenient for performing this ad­justment. During recording, the input signal FUNCTION will auto­matically switch to VIDEO 1. (After recording, press the 0 button without stopping will re­turn to the position where recording was started.)
1. Press FUNCTION button to select VIDEO 1. (This step is not necessary if the above test mode has already been set.)
2. Insert a tape into deck B, press the r REC button, and then press the · button to start recording.
3. Mode: Record
VIDEO 1 (AUDIO) IN
1) 315 Hz
2) 10 kHz
AF OSC
attenuator
600
} 50 mV (–23.8 dB)
blank tape CS-123
set
Procedure:
INTRODUCTION
When set to the test mode performed in Tape Speed Adjust­ment, when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is set. This “REC memory mode” is convenient for performing this adjustment. During recording, the input signal FUNCTION will au­tomatically switch to VIDEO 1. (After recording, press the 0 button without stopping will re­turn to the position where recording was started.)
1. Press FUNCTION button to select VIDEO 1. (This step is not necessary if the above test mode has already been set.)
2. Insert a tape into deck B, press the r REC button, and then press the · button to start recording.
3. Mode: Record
VIDEO 1 (AUDIO) IN 315Hz 50 mV (–23.8 dB)
AF OSC
attenuator
600
set
blank tape CS-123
4. Mode: Playback
recorded position
set
MD OUT
level meter
5. Confirm playback the signal recorded in step 2 become adjust­ment level as follows. If these levels do not adjustment lev el, adjust the R V341 (L-CH) and R V441 (R-CH) on the A UDIO board to repeat steps 3 and 4.
Adjustment level: The playback output of 10 kHz le vel dif ference
against 315 Hz reference should be ± 1.0 dB.
Adjustment Location: AUDIO board
Adjustment Location:
[AUDIO BOARD] (Conductor Side)
RV341(Lch),RV441(Rch) Record Bias
RV311(Lch),RV411(Rch) Playback Level (Deck A)
4. Mode: Playback
recorded position
set
MD OUT
level meter
5. Confirm playback the signal recorded in step 2 become adjust­ment level as follows. If these levels do not adjustment lev el, adjust the R V301 (L-CH) and R V351 (R-CH) on the MAIN board to repeat steps 3 and 4.
Adjustment level:
CN403 playback level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
Adjustment Location: MAIN board
[MAIN BOARD] (Conductor Side)
RV301 RV401
RV441 RV341
RV301(Lch),RV401(Rch) Playback Level (Deck B)
RV311
RV411
– 18 –
Record Level (Lch) RV301
1 3
14
15
28
1
IC301
RV351 Record Level (Rch)
29
56
42
43
HCD-DR4/DR5/DR6/DR440/W300/W5000/XB500
TRANS board
SUB TRANS board
(W300/W5000/XB500)
MAIN board
PA board
CD-L board
CD-R board
LED (PANEL) board
DOOR SWITCH board
SECTION 7
DIAGRAMS
CD SECTION
Note:
1. CD Block is basically constructed to operate without adjustment. Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M impedance.
4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks.
S Curve Check
BD board
TP (FE) TP (VC)
Procedure :
1. Connect the oscilloscope to test points TP (FE) and TP (VC).
2. Connect TP (FEI) and GND, and TP (AGCCON) and GND of the BD board with lead wires.
3. Press the 1/u button to turn the set ON.
4. With the disc (YEDS-18) loaded, press the ·P button and perform focus search. (Focus search will be performed in the same way even while the disc table is pushed in and out.)
5. Check the symmetry and peak to peak level of the oscilloscope waveform (S curve) at this time.
oscilloscope
+ –
E-F Balance (1 Track Jump) c heck
oscilloscope
BD board
TP (TE) TP (VC)
+ –
Procedure:
1. Connect oscilloscope to test point TP (TE) on BD board.
2. Press the 1 /u button to turn the unit ON.
3. Put disc (YEDS-18) in to play the number five track.
4. Press the ·P button.
5. Check the level B of the oscilloscope's waveform and the A (DC voltage) of the center of the Traverse wave­form. Confirm the following:
• A/B x 100 = less then ± 22 (%)
• B = 1.3 ± 0.6 Vp-p
1 track jump waveform
Center of the waveform
B
0V
A (DC voitage)
7-1. CIRCUIT BOARDS LOCATION
PANEL FL board
TC-A board
PANEL VR board
FRONT INPUT board
TUNER UNIT
JACK board
TC-B board
S-curve waveform
symmetry
A
B
Within 3
±
1 Vp-p
6. After check, remove the lead wire connected in step 2. Note: • Try to measure several times to make sure than the ratio of
A : B or B : A is more than 10 : 7.
• Tak e sweep time as long as possible and light up the bright­ness to obtain best waveform.
RF Level Check
oscilloscope
BD board
TP (RF) TP (VC)
+ –
Procedure :
1. Connect oscilloscope to test point TP (RF) and TP (VC) on BD board.
2. Press the 1/u button to turn the set ON.
3. Put disc (YEDS-18) in and playback 5 track.
4. Confirm that oscilloscope waveform is clear and check RF sig­nal level is correct or not.
Note: Clear RF signal waveform means that the shape “” can be
clearly distinguished at the center of the waveform.
level : 1.3
±
0.6 Vp-p
Adjustment Location :
[ BD BOARD ] — SIDE A —
TP (VC)
TP (RF)
TP (AGCCON)
TP (FE)
TP (TE)
TP (FE1)
Symmetry
TABLE SENSOR board
LEAF SW board
AUDIO board
BD board
RF signal waveform
VOLT/DIV : 200mV TIME/DIV : 500ns
level : 1.45 ± 0.25 Vp-p
– 19 –
CD MOTOR board
LED (CD) board
– 20 –
HCD-DR4/DR5/DR6/DR440/W300/W5000/XB500
7-2. BLOCK DIAGRAMS
– BD (CD) SECTION –
OPTICAL PICK-UP BLOCK
(KSS-213B/K-N)
• SIGNAL PATH : CD : Digital out
09
DETECTOR
E
ABC
D
F
FD
PD
TRACKING
COIL
FOCUS
COIL
LASER
DIODE
LD
POWER
SPINDLE
M102 SLED
MOTOR
M101
MOTOR
VCC VC
A C
D
B
E
F
LD
DRIVE
Q101
T+
T–
F+
F–
SD+
M
SD–
SP+
M
SP–
A
5
C
7
D
8
B
6
E
11
F
10
LD
3
PD
4
VREF
IC102 FOCUS/TRACKING COIL DRIVE SPINDLE/SLED MOTOR DRIVE
CH2OUTR
11
12
14
13
17
18
15
16
CH2OUTF
CH1OUTF
CH1OUTR
CH3OUTF
CH3OUTR
CH4OUTF
CH4OUTR
CH2FIN
CH2RIN
CH1FIN
CH1RIN
CH3RIN
CH3FIN
CH4SIN CH4BIN
APCLD/PD
MUTE
SUMMING
TRACKING
AMP
5 6
2 3
23 24
25 27
20
IC103
RF AMP
RF
AMP
FOCUS ERROR
AMP
ERROR
AMP
TFDR TRDR
FFDR FRDR
SRDR SFDR
BUFFER
HOLD SW
VC
VC
RF EQ
AMP
REF
RF
16
FF
14 49
TE
13
12
VC
LDON
22
1521
INTEG­RATOR
INTEG­RATOR
VC
IC101
DIGITAL SERVO
DIGITAL SIGNAL PROCESSOR
RF AC
51
ASY1
ASYMMETRY CORRECTION
ASY0
48
VC
38
CE
42
RFDC
43
FE TE
SE
CE
TFDR TRDR
FFDR FRDR
SRDR SFDR
MDP
OPERATIONAL
AMPLIFIER
ANALOG SWITCH
PWM
GENERATOR
TRACKING
PWM
GENERATOR
FOCUS
PWM
GENERATOR
SLED PWM
GENERATOR
DIGITAL
CLV
39 41
40
42
30 31
32 33
29 28
26
DIGITAL
PLL
A/D
CONVERTER
SERVO DSP
TRACKING
SERVO
FOCUS SERVO
SLED
SERVO
16K
RAM
EFM
DEMODULATION
SUBCODE
PROCESSOR
SERIAL IN
INTERFACE
OVER SAMPLING
DIGITAL FILTER
3rd ORDER
NOISE SHAPER
PWM PWM
DATA BUS
ERROR
CORRECTOR
D/A
INTERFACE
SERVO
AUTO
SEQUENCER
TIMING
LOGIC
DIGITAL
OUT
CPU
INTERFACE
SERVO
INTERFACE
XTA1
STAO
D OUT
XRST SQSO SQCK
SENS
DATA
XLAT
CLOK
SCOR XLON
SCLK SSTP
RMUT
LMUT
LMUT
AIN1
LOUT1
LOUT2
AIN2
LOUT2
66
67
60
3 1 2
8
5 6
7
20 14
9
27
79
80
70
71
72
77
76
75
S101
LIMIT SW
X101
16.9344MHz
DOUT
XRST SQSO
SENS
DATA XLT
CLOK
SCOR
SQCK +5V
L OUT
R OUT HOLD
A
MAIN
SECTION
(Page 25, 27)
– 21 – – 22 –
– DECK SECTION –
HCD-DR4/DR5/DR6/DR440/W300/W5000/XB500
HP101 PB HEAD (DECK A)
REC/PB HEAD
(DECK B)
HRPE101
ERASE HEAD
PB A/B
MS OUT
TC PB L
LM ON/OFF
NORM/HIGH
NR ON/OFF
REC/PB/PASS
TC REC L
BIAS ON/OFF RM ON/OFF
ALC ON/OFF
RELAY
CAPM CNT1
CAPM CNT2
CAP M H / L
A SHUT
B
MAIN
SECTION
(Page 25,
26, 27)
17
2
DOLBY NR
RECOUT
D
32
S1008 B CrO
2
19
B NORM/CROM/
METAL
PAS
DOL
BIAS SW
M
31, 33
M1
CAPSTAN
MOTOR
DOLBY TYPE B
CN301
1
R CH
28
27
M
MS
26
PB OUT
LM ON/
OFF
NORM/
HIGH
NR ON/
OFF
PB
LIN
BIAS ON/OFF
RM ON/OFF
ALC ON/OFF
CAP MOTOR CONTROL Q336-343
CONTROL
RV1002
NORMAL
SPEED
SPEED
Q1001
40
25
18
23
24
43
20 22 15
RV1001
HIGH
SPEED
3
SWITCH
Q335
REEL DETECT IC1001
S1004
A CrO
RV311
4
PLAYBACK
LEVEL
DECK A
RV301
PLAYBACK
LEVEL
DECK B
RV341
REC
BIAS
REC BIAS
BIAS OSC
T621, Q621, 622
IC611
L
R
L
R
X
R CH
R CH
3
P
ERASE BIAS
IC601
1
IC602
R
REC/PB
16
PB-A/B
A IN
48
B IN
46
RV301
REC LEVEL
+7.5V
Q623
EQIN
38
EQOUT
36
70
120
DOLBY NR IC301
A 120/70
39
REEL DETECT IC1002
S1001 (A PLAY)
• R CH : Same as L ch
• SIGNAL PATH
+5V
S1002 (B PLAY)
: PB (DECK A) : PB (DECK B) : REC (DECK B)
09
• PLUNGER SOLENOID is supplied as the MECHANICAL BLOCK ASSY.
A DECK/ B DECK PLUNGER
TRIGGER MOTOR CONTROL Q331-334
S1003
(A HALF)
S1005
(REC A)
S1006
(B HALF)
S1009
(REC B)
+5V
+5V
B SHUT
A PLAY
B PLAY
A HALF
B HALF/REC A/REC B
B TRIG
A TRIG
– 23 –
– 24 –
HCD-DR4/DR5/DR6/DR440/W300/W5000/XB500
– MAIN (1/2) SECTION –
IC191
AV SWITCH
6
IN3
IN4
IN1
1
B
A
2 3 5
46 45 28
IC181 SELECTOR
12
X0
X1
14
15
X2
A
10 9
46 45
X
B
VD OUT
13
10
C
IC601
PHONO AMP
3
DECK
SECTION
(Page 24)
CD
SECTION
(Page 22)
POWER
SECTION
(Page 30,
32)
VIDEO 2
IN
VIDEO
IN
PHONO
(L IN)
FM/AM TUNER TUNER UNIT IS SUPPLED AS THE ASSEMBLED BLOCK
B
A
MD (L IN)
C
R, AUDIO
(L IN)
V2, AU,
L-CH IN
FRONT
(L IN)
J804
J702
J701
ST-L
TC PB L
CD-L
J701
MIC-SIG
J701
J804
J703
J702
VIDEO
OUT
IC101
SOUND PROCESSOR 1
30
L+R
1
69
IN A2
IN B2
68
IN C2
67
IN D2
66
65
IN E2
MIC IN
2
64
IN F2
BUS OUT2
REC B2
REC A2
BBA2
BBB2
BUF IN2
57
36
58
39
38
37
SWITCH
Q114
44 34
SWITCH
Q115
SWITCH
Q111
TC REC L
SWITCH
Q112
(TA-MUTE)
7
MUTE
SWITCH
Q113
SPEANA
J701
L-CH SIG
TC REC L
D
REC OUT
E
B
DISPLAY
SECTION
(Page 33)
POWER
SECTION
(Page 29, 31)
DECK
SECTION
(Page 24)
• R CH: Same as L ch
• SIGNAL PATH : FM : CD : PB : REC : VIDEO/MD
09
– 25 –
MUTE
SWITCH
Q803
D807
RESET
SWITCH
Q802
MUTE
SWITCH
Q804
6
3
LINE-MUTE
F-RELAY
MAIN CONTROL
IC501 (1/2)
BASS FREQ FUNC-SEL1
DBFB-H/L
PL-CLK
PL-DATA
PL-LAT
V-MUTE
SW-MODE
493-LAT
493-DATA
7
7
23
23
24
24
25
25
28
28
34
34
38
38
44
44
45
45
46
46FUNC-SEL0
47
47
48
48493-MUTE
22AC-CUT
RESET
F-RELAY
G
F
DISPLAY
SECTION
(Page 33)
POWER
SECTION
(Page 29, 31)
– 26 –
– MAIN (2/2) SECTION –
HCD-DR4/DR5/DR6/DR440/W300/W5000/XB500
H
POWER
SECTION
(Page 30,
A
BD (CD)
SECTION
(Page 22)
B
DECK
SECTION
(Page 24)
FM/AM TUNER TUNER UNIT IS SUPPLED AS THE ASSEMBLED BLOCK
32)
B-HALF/REC A/REC B
HP.SW
SCOR
SQ-DATA
SQ-CLK
CD-DATA
CD-CLK
SENS
HOLD X-LAT X-RST
TRAY.SENS
TBL.L TBL.R
UP SW
LED
B TRG A TRG
CAPM-CNT 2 CAPM-CNT 1
CAP-M-H/L
MS OUT
LM ON/OFF
REC/PB/PASS
NR ON/OFF
RM ON/OFF
BIAS ON/OFF
NORM/HIGH
PB A/B
ALC ON/OFF
B PLAY A PLAY A-HALF
B SHUT A SHUT
RELAY
RDS-INT
RDS-DATA
ST-MUTE
STEREO
TUNED
ST-CE
ST-DOUT
ST-DIN
ST-CLK
IC781
OPTIC
TRANSMITTING
D.OUT
36 H/P IN
19
SCOR
32
SQ-DATA
33
SQ-CLK
35
CD-DATA
37
CD-CLK
56
SENS
57
HOLD
58
XLT
59
XRST
61
DISC-SENS
63
TBL-L
65
TBL-R
68
ENC 3/UP-SW ENC 2/DISC-LED
69
72
B-TRG
73
A-TRG
74
CAPM-CNT 2
75
CAPM-CNT 1
76
CAP-M-H/L
77
AMS IN
78
TC-MUTE
79
R/PB/PAS
80
NR-ON/OFF REC-MUTE
81 82
BIAS
83
EQ-H/N
84
PB-A/B ALC
85 86
B-PLAY-SW
87
A-PLAY-SW
88
A-HALF
89
B-HALF
90
B-SHUT
91
A-SHUT TC-RELAY
100
20
RDS-INT
21
RDS-DATA
49
ST-MUTE
50
STEREO
51
TUNED
52
ST-CE
53
ST-DOUT
54
ST-DIN
55
ST-CLK
MAIN CONTROL
IC501 (2/2)
STBY RELAY
STK-POWER
PROTECT
FL OFF
HP MUTE
WAKE UP
IIC-CLK
IIC-DATA
XC-IN
XC-OUT
X-OUT
X-IN
POWER
CD-POWER
IC931
+UNREG, 12V
W300,W5000,XB500
1
1
27
27
42
42
43
43
93
93
18
18
29
29
30
30
X501
10
11
X502
16MHz
13
15
2
5
43 42 93
1
27
30 29 18
POWER ECO HP MUTE
STK POWER PROTECT
DATA CLOCK WAKE UP
I
POWER
SECTION
(Page 29, 31)
J
DISPLAY SECTION
(Page 33)
UN–10V
2
UN+10V
+10V
1 3
REG
IC932
+12V
1 3
REG
FAN DETECTOR
D405-409
IC951
–7V
2 3
REG
Q932 SWITCH
IC901
+7V
1 3
REG
IC911
+5V
1 3
REG
Q914
SWITCH
5
IC921
DETECTOR
Q905
SWITCH
2
SWITCH
SWITCH
2
Q931
Q931
Q901
Q932 SWITCH
Q932 SWITCH
Q902 SWITCH
SWITCH
2
SWITCH
Q901
Q913
FAN SWITCH
Q961, 963
IC933
+7V
1 3
REG
Q902 SWITCH
(LED–7V)
(LED+7V)
(D+5V SW)
(CD D+5V SW)
(CD A+5V SW)
PL A+10V
ST +10V
FAN901
FAN
TC MOTOR+12V
M+7V (UNSW)
7V
A–7.5V
–V BIAS
–7
TC–7V
–7V
A+7.5V
+V BIAS
–7
TC–7V
–7V
LED 5V
LED 5V
D+5V UNSW
5V
AU D+5V
EVER +5V
D+5V (SW)
A+5V (SW)
L
POWER
SECTION
(Page 29, 31)
+5V
1 3
REG
09
• R CH : Same as L ch
Q921
SWITCH
CD D+5V SW
CD A+5V SW
– 27 – – 28 –
HCD-DR4/DR5/DR6/DR440/W300/W5000/XB500
– POWER SECTION – (DR4, DR5, DR6, DR440 model)
MAIN 1
SECTION
(Page 26)
MAIN 1
SECTION
(Page 26)
MAIN 2
SECTION
(Page 28)
G
E
L
MIX MIC
J801
F-RELAY
L-CH IN
EVER +5V
HP-MUTE
POWER AMP & VOLUME CONTROL
22
THERMAL
SENSOR
13
12
D804
HEAD PHONE
MUTE Q833
MIC AMP
IC850 (1/2)
IC801
CONTROL
VOLUME
CONTROL
8
MUTE
Q834
6
5
MIC VOLUME
RV850
15
VOLUME CONTROL D802, 852
THERMAL
SENSOR Q831-832
ECHO CONTROL
9
LPF 2 IN
OP 2 IN
11
1
LPF 1 IN
PROTECT
DC AMP
Q433-434
L-CH THERMAL
PROTECT SWITCH
Q801
IC851
LPF 1 OUT
LPF 2 OUT
OP 2 OUT
LATCH
DRIVER
Q432
MIC LEVEL
RV851
2
8
10
RELAY
DRIVER
Q401-402
LATCH
DRIVER
Q437
PROTECT
SWITCH
Q439
MIC AMP
IC850 (2/2)
RY401
PROTECT
SWITCH
Q431
R-CH
MIC-SIG
MIC-SIG
J803
PHONES
HP.SW
TM401
L
FRONT
R
K
C
H
DISPLAY SECTION
(Page 33)
MAIN 1
SECTION
(Page 25)
MAIN 2
SECTION
(Page 27)
MAIN 2
SECTION
(Page 27)
09
I
STK-POWER
• R CH : Same as L ch
• SIGNAL PATH : FM
PROTECT
MUTE DRIVE
Q804
MUTE
SWITCH
Q803
VF (–35V)
SWITCH
Q904
–35V REG
Q903
+VH
RECT D831
+UNREG. 12V
UN +10V
UN –10V
AC-L
AC-L
RECT
D833-836
RECT
D841-844
RECT D832
VF
VF
POWER
TRANSFORMER
T951
MX ONLY
JW966
JW969
JW968
EXCEPT MX,AUS,TH
VOLTAGE
SELECTOR
VS901
AUS,TH
ONLY
AC
IN
– 29 – – 30 –
– POWER SECTION – (W300, W5000, XB500 model)
J801
MIX MIC
MIC AMP
IC850 (1/2)
MIC VOLUME
RV850
9
11
1
ECHO CONTROL
IC851
LPF 2 IN
OP 2 IN
LPF 1 IN
LPF 1 OUT
LPF 2 OUT
OP 2 OUT
HCD-DR4/DR5/DR6/DR440/W300/W5000/XB500
DISPLAY
MIC LEVEL
RV851
2
8
10
MIC AMP
IC850 (2/2)
MIC-SIG
MIC-SIG
J803
PHONES
K
C
SECTION
(Page 33)
MAIN 1
SECTION
(Page 25)
MAIN 1
SECTION
(Page 26)
MAIN 1
SECTION
(Page 26)
MAIN 2
SECTION
(Page 28)
MAIN 2
SECTION
(Page 27)
09
G
E
L
I
• R CH : Same as L ch
• SIGNAL PATH : FM
F-RELAY
L-CH IN
W300 W5000 XB500
EVER +5V
HP-MUTE
STK-POWER
PROTECT
W300, W5000, XB500
POWER
ECO
POWER AMP & VOLUME CONTROL
22
14
D804
HEAD PHONE
MUTE Q833
MUTE
DRIVE
Q804
THERMAL
SENSOR
13
IC801
12
VOLUME
CONTROL
8
MUTE
CONTROL
Q834
MUTE
SWITCH
Q803
MAIN 2
HP.SW
RECT
D833-836
RECT
D841-844
RECT D832
RECT
D902-905
RECT
D907-910
SWITCH
Q904-905
SWITCH
Q906
TM401
L
FRONT
R
TM402
L
REAR
R
W300 ONLY
TRANSFORMER
RELAY CONTROL
SUB-TRANSFORMER
VF
RY401
15
W300 W5000
7
XB500
6
5
VOLUME
CONTROL
D802, 852
THERMAL
SENSOR
Q831-832
PROTECT
DC AMP
Q433-434
L-CH THERMAL
PROTECT SWITCH
Q801
LATCH
DRIVER
Q432
RELAY
DRIVER
Q401-402
Q903
Q907
+5.6V
PROTECT
SWITCH
Q431
RECT D831
+UNREG. 12V
+5.6V
3
REG
IC901
POWER SWITCH
Q902
UN +10V
UN –10V
VF
LATCH
DRIVER
Q437
PROTECT
SWITCH
Q439
+VH –VH
VF
–30V REG
SWITCH
R-CH
JW76
R-CH
+VL
–VL
1
H
POWER
T951
STANDBY
Q901
T901
SECTION
(Page 27)
XB500 ONLY
230V
JW954
F951
120V
W300 W5000 ONLY
STANDBY
RELAY RY901
AC
IN
– 31 – – 32 –
HCD-DR4/DR5/DR6/DR440/W300/W5000/XB500
– DISPLAY SECTION –
(Page
F
26)
MAIN 1 SECTION
MAIN 2 SECTION
(Page
27)
(Page 30, 32)
J
RESET
DATA
CLOCK
WAKE UP
A –7V A +7V
D671 – D675
REC LEVEL
OUTPUT
DISPLAY CONTROL (FOR MIC)
K
POWER SECTION MAIN 1 SECTION
MIC–SIG
SPE–ANA
3 4 6 5
LINE NF LINE IN REC IN REC NF
D
(Page 26)
IC603
REC LEVEL
12.5MHz
F06 F05 F04 F02 F01
X601
11 12 13 14 16 17
70
72
73 78 79 22
21 20 19 18 17 16
X IN
X OUT
RESET I2C DATA
2
I
C CLK
WAKE UP
ALL BAND BPF 4 BPF 3 BPF 2 BPF 1 BPF 0
SEG-1
45 67
DISPLAY CONTROL
IC601
23
GR-3 14, 2
29VF40, 42
SIRCS
JOG A JOG B
LED SCK
LED LATCH
LED DAT
D-SW
LED SEL
VOLUME A VOLUME B
KEY 0
KEY 4
DAILY LED
REC LED LED-EC0
GR-1 GR-15 GR-16
REMOTE
1
2 8
3 4 5
80
7
9
10
11
15
74 75 77
43 28 27
CONTROL
RECIEVE
IC602
S702
JOG
ROTARY
ENCODER
S691
6
OPEN
Q601 – Q603
LED POWER
SWITCH
S701
VOLUME
ROTARY
ENCODER
KEY MATRIX
Q605 – Q607 LED DRIVER
Q608 – Q610
DRIVER
14
CLK
15
STB
13
DATA
D604 – D607
D604 – D607
D601 – D603
SERIAL
PARALLEL
CONVERTER
IC604
D611, D612, D616, D618 – D621, D623 – D627, D635 – D638
1
P3
5
P5
• 7
P7
9
P11
20
P12
22
P14
P1
17
P2
19
D631, D632
D700
FLUORESCENT INDICATOR TUBE
09
FL601
– 33 – – 34 –
HCD-DR4/DR5/DR6/DR440/W300/W5000/XB500
2.5V
APPROX 500mVp-p (PLAY)
2.5V
APPROX 200m Vp-p (PLAY)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.
• All resistors are in and 1/ specified.
¢
C : panel designation.
U : B+ Line.
V : B– Line.
H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
• Voltages are taken with a VOM (Input impedance 10 M).
• Waveforms are taken with a oscilloscope.
• Circled numbers refer to wavefor ms.
• Signal path.
• Abbreviation
: internal component.
Note:
The components identi-
fied by mark ! or dotted line with mark ! are criti­cal for safety.
Replace only with part
number specified.
under no-signal (detuned) conditions. Voltage var iations may be noted due to normal produc-
tion tolerances. Voltage var iations may be noted due to normal pro-
duction tolerances.
F : FM g : VIDEO/MD E : PB (DECK A) d : PB (DECK B) G : REC (DECK B) J : CD c : digital out I : PHONO
CND : Canadian model. AUS : Australian model.
4
W or less unless otherwise
Note:
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
For printed wiring boards.
Note:
X : parts extracted from the component side.
®
b : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
: Through hole.
¢
: internal component.
WAVEFORMS – BD (CD) SECTION –
1
16.9MHz
IC101 XTAI
2
(PLAY)
IC101 RF AC
3
IC101 TE
4
IC101 FE
5
7.5µsec
IC101 MDP
3.1Vp-p
1.2Vp-p
2.4Vp-p
– MAIN (2/5) SECTION –
1
5.5Vp-p
16MHz
IC501 X-OUT
2
5.2Vp-p
32.768kHz
IC501 XC-OUT
– PANEL FL SECTION –
1
3.4Vp-p
12.5MHz
IC601 &™ X-OUT
• Indication of transistor
C
EB
These are omitted
C
Q
These are omitted
EB
– 35 –
– 36 –
Loading...
+ 61 hidden pages