Sony Cyber-shot DSC-W5,Cyber-shot DSC-W7,Cyber-shot DSC-W15,Cyber-shot DSC-W17 Service Manual
SERVICE MANUAL
LEVEL 2
Link
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
Link
Revision History
Revision History
How to use
Acrobat Reader
How to use
Acrobat Reader
Sony EMCS Co.
DSC-W5/W7/W15/W17
•For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-856-51).
•For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-856-41).
• This service manual contains information for Japanese model as well.
• Reference No. search on printed wiring boards is available.
•Table for Differences of Function of Each Model
• Note in Lens Frame Installation
•Method for Copying or Erasing the Data in Internal Memory.
• Exchange Method of Barrier Assy
Ver. 1.5 2007.09
DIGITAL STILL CAMERA
On the CH-168 and SY-001 boards
This service manual procides the information that is premised the
circuit board replacement service and not intended repair inside the
CH-168 and SY-001 boards.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the CH-168 and SY-001 boards are not shown.
The following pages are not shown.
Schematic diagrams.................. Pages 4-11 to 4-30
Printed wiring boards ................ Pages 4-39 to 4-42
Waveforms ................................ Pages 4-45 and 4-46
Mounted parts location.............. Pages 4-48
Electrical parts list ..................... Pages 5-7 and 5-9 to 5-12
The above-described information is shown in service manual Lev el 3.
DSC-W5/W7/W15/W17
2007I0500-1
© 2007.9
Published by Kohda TEC9-876-856-31
Photo: DSC-W5/Silver
DSC-W5/W7
US Model
Canadian Model
Argentine Model
Brazilian Model
Japanese Model
DSC-W5/W7/W15/W17
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Korea Model
Tourist Model
DSC-W5/W7/W15
Chinese Model
— 2 —
DSC-W5/W7/W15/W17
SPECIFICATIONS
Camera
[System]
Image device DSC-W7/W17:
9.11 mm (1/1.8 type) color
CCD, Primary color filter
DSC-W5/W15:
9.04 mm (1/1.8 type) color
CCD, Primary color filter
Total pixel number of camera
DSC-W7/W17:
Approx. 7 410 000 pixels
DSC-W5/W15:
Approx. 5 255 000 pixels
Effective pixel number of camera
DSC-W7/W17:
Approx. 7 201 000 pixels
DSC-W5/W15:
Approx. 5 090 000 pixels
Lens Carl Zeiss Vario-Tessar
3 zoom lens
f = 7.9 - 23.7 mm (38 - 114 mm
when converted to a 35 mm still
camera)
F2.8 - 5.2
Exposure control Automatic exposure, Manual
exposure, Scene Selection (7
modes)
White balance Automatic, Daylight, Cloudy,
Fluorescent, Incandescent,
Flash
File format (DCF compliant)
Still images: Exif Ver. 2.2
JPEG compliant, DPOF
compatible
Movies: MPEG1 compliant
(Monaural)
Recording media Internal memory 32 MB
Memor y Stick
Flash Recommended distance (ISO
set to Auto): 0.2 m to 4.5 m
(7 7/8 inches to 14 feet 9 1/4
inches) (W)/0.3 m to 2.5 m
(11 7/8 inches to 8 feet 2 1/2
inches) (T)
[Input and Output connectors]
A/V OUT (MONO) jack (Monaural)
Minijack
Video: 1 Vp-p, 75 Ω,
unbalanced, sync negative
Audio: 327 mV (at a 47 kΩ
load)
Output impedance 2.2 kΩ
USB jack mini-B
USB communication
Hi-Speed USB (USB 2.0
compliant)
[LCD screen]
LCD panel 6.2 cm (2.5 type) TFT drive
Total number of dots
115 200 (480×240) dots
[Power, general]
Power HR 15/51:HR6 (size AA)
Nickel-Metal Hydride batteries
(2), 2.4 V
R6 (size AA) Alkaline batteries
(2, not supplied), 3 V
AC-LS5K AC Acaptor (not
supplied), 4.2 V
Power consumption
(during shooting with the LCD screen on)
DSC-W7/W17: 1.2 W
DSC-W5/W15: 1.1 W
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
−20°C to +60°C (−4°F to
+140°F)
Dimensions 91×60×37.1 mm
(3 5/8×2 3/8×1 1/2 inches)
(W/H/D, excluding maximum
protrusions)
Mass Approx. 253 g (8.9 oz)
(including two batterries and
wrist strap)
Microphone Electret condenser microphone
Speaker Dynamic speaker
Exif Print Compatible
PRINT Image Matching III
Compatible
PictBridge Compatible
BC-CS2A/CS2B Ni-MH battery charger
Power requirements
AC 100 to 240 V, 50/60 Hz,
3 W
Output voltage AA: DC 1.4V 400 mA × 2
AAA: DC 1.4 V 160 mA × 2
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
−20°C to +60°C (−4°F to
+140°F)
Dimensions Approx. 71×30×91 mm
(2 7/8×1 3/16×3 5/8 inches)
(W/H/D)
Mass Approx. 90 g (3 oz)
Design and specifications are subject to change
without notice.
— 3 —
DSC-W5/W7/W15/W17
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY .
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS P AR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMA TIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show ob vious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. FLEXIBLE Circuit Board Repairing
•Keep the temperature of the soldering iron around 270°C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky , less prone to flo w) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Table for differences of function
Model DSC-W5 DSC-W7 DSC-W15 DSC-W17
US, CND, AEP, UK, US, CND, AEP, UK, AEP, UK, AEP, UK
Destination E, AUS, HK, CH, E, AUS, HK, CH, E, AUS, HK, CH, E, AUS, HK,
KR, AR, BR, J, JE KR, AR, BR, J, JE KR, JE KR, JE
CCD imager 5 255 000 pixels 7 410 000 pixels 5 255 000 pixels 7 410 000 pixels
Total pixel (Effective pixel) (5 090 000 pixels) (7 201 000pixels) (5 090 000 pixels) (7 201 000pixels)
CD board CD-545 CD-546 CD-545 CD-546
•Abbreviation
AR : Argentine model
AUS: Australian model
BR : Brazilian model
CH : Chinese model
CND: Canadian model
HK : Hong Kong model
J: Japanese model
JE : T our ist model
KR : Korea model
Note: DSC-W15/W17 are the same as DSC-W5/W7
except accessories and packing materials.
— 4 —
DSC-W5/W7/W15/W17
TABLE OF CONTENTS
1. SERVICE NOTE
1-1. Note for Repair ································································1-1
1-2. Discharging of The SY-001 Board’s Charging Capacitor
(C901)··············································································1-1
1-3. Note in Lens Frame Installation ······································1-2
1-4. Description on Self-diagnosis Display ···························· 1-2
1-5. Method for Copying or Erasing the Data in Internal
Memory ···········································································1-3
1-6. Process After Fixing Flash Error·····································1-4
2. DISASSEMBLY
2-1. Disassembly·····································································2-1
2-2. SY-001 Board Service Position ·······································2-3
2-3. Exchange Method of Barrier Assy ··································2-5
2-3-1.Peel Off Old Ornamental Ring A ····································2-5
2-3-2.Remove Old Barrier Assy ················································2-6
2-3-3.Install New Barrier Assy ·················································2-6
2-3-4.Adhere the Ornamental Ring A ·······································2-7
2-4. Circuit Boards Location ··················································2-8
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/2)···········································3-1
3-2. Overall Block Diagram (2/2)···········································3-3
3-3. Power Block Diagram ·····················································3-5
4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagram ··············································4-1
4-2. Schematic Diagrams························································4-5
CD-545 FLEXIBLE (CCD IMAGER) ···························4-7
CD-545 FLEXIBLE (CCD IMAGER) ···························4-9
SW-001 BOARD (CONTROL SWITCH)····················4-31
CONTROL SWITCH BLCOK·····································4-32
4-3. Printed Wiring Boards ···················································4-35
CD-545 FLEXIBLE······················································4-37
CD-546 FLEXIBLE······················································4-38
SW-001 ········································································· 4-44
4-5. Mounted Parts Location ················································4-47
5. REPAIR PARTS LIST
5-1. Exploded Vie ws ·······························································5-2
5-1-1.Overall Assembly ··························································· 5-2
5-1-2.Cabinet (Front) Block······················································ 5-3
5-1-3.Main Block Assembly ····················································· 5-4
5-1-4.Lens Block Assembly······················································ 5-5
5-2. Electrical Parts List ·························································5-6
Section Title Page Section Title Page
1-1
DSC-W5/W7/W15/W17
1-2. DISCHARGING OF THE SY-001
BOARD’S CHARGING CAPACITOR
(C901)
The charging capacitor (C901) of SY-001 board is charged up to
the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
1 kΩ/1 W
Wrap insulating tape.
Discharging the Capacitor
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
1. SERVICE NOTE
R:1 kΩ/1 W
(Part code:
1-215-869-11)
1-2
DSC-W5/W7/W15/W17
1-3. NOTE IN LENS FRAME INSTALLATION
When tightening a screw, have both sides of the lens block assembly so as not for the load to depend.
P2 tapping screw
Lens block assembly
Lens frame
assembly
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
Display Code
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the “Memory Stick” or internal
memory.
Cause
Trouble with hardware.
“Memory Stick” or internal memory is
unformatted.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
E:92:ss
1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Insert a new “Memory Stick”. “Memory Stick” is broken.
Turn the power off and on again. Trouble with internal memory. INTERNAL MEMORY ERROR
Checking of lens drive circuit.
When failed in the focus and zoom
initialization.
—
Checking of flash unit or replacement
of flash unit. (Note)
Insert batteries correctly.
Abnormality when flash is being
charged.
Batteries are not inserted correctly.
Note: After repair, be sure to perfom “1-6. PROCESS AFTER FIXING FLASH ERROR”.
1-3
DSC-W5/W7/W15/W17
1-5. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note: 1 When replacing the SY-001 board, erase the data in internal memory of the board before replacement.
Note: 2 When replacing the SY-001 board or the IC381 on the SY-001 board, execute formatting and initialize the internal memory after
replacement.
Method for Copying the Data in Internal Memory
Method for Formatting the Internal Memory
Copies all images in the internal memory to a “Memory Stick”.
1 Insert a “Memory Stick” having 32 MB or larger capacity.
2 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.
3 Select [OK] with v, then z.
Copying starts.
• Use fully charged Nickel-Metal Hydride batteries or the AC Adaptor (not supplied). If you attempt to
copy image files using batteries with little remaining charge, the batteries may run out, causing copying to
fail or possibly corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick” after copying, then execute the [Format] command in
Internal Memory Tool).
• You cannot select a folder copied on a “Memory Stick”.
• A (Print order) mark added to an image is deleted when you copy data.
Copy
OK
See the following procedure.
Cancel
Cancels the copying.
Copying
102_COPY
Formats the internal memory.
• Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be erased Ready?” appears.
2 Select [OK] with v, then press z.
The format is com
p
lete.
Format
OK
See the following procedure.
Cancel
Cancels the formatting.
1-4E
DSC-W5/W7/W15/W17
1-6. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code
Initializes the setting to the default setting.
1 Select [OK] with v on the control button, then press z.
The message “Initialize all settings Ready?” appears.
2 Select [OK] with v, then press z.
The settings are reset to the default setting.
• Make sure that the power is not disconnected during resetting.
Initialize
OK
See the following procedure.
Cancel
Cancels the resetting.
DSC-W5/W7/W15/W17
2-1 2-2
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
2. DISASSEMBLY
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two
points with the short jig about 10
seconds.
R:1 kΩ/1 W
(Part code:
1-215-869-11)
1
1
3
1
4
5
qa
0
9
9
qs
2
6
7
8
1 P2 torasuta screw (M1.7)
x4
2 Claw
x1
3 Cabinet (rear) block assembly
4 Screw (M1.7)
x2
5 SW-001 board
6 Flexible board x2: CN451, 452
1 Screw (M1.7)
x2
2 LCD frame
3 Te rminal guard
4 Fuse label
5 Remove the control switch block.
1 Connector: CN001
2 Battery holder
3 Connector
x2
: CN201, 401
4 Lens block
1 Ornamental ring A
2 Tapping screw
x2
3 Barrier assy
1
2
3
Note: When you exchange rings, be sure
to follow the procedure carried on
"2-3. Exchange Method of Barrier
Assy" (2-5 page).
1
2
3
4
9
5
7
8
0
6
3
4
1
2
6 Connector: CN753
7 Control switch block
8 Connector x2:
CN801, 802
9 Remove the cabinet (front) block.
0 Cabinet (front) block
7 Claw
x1
8 BT side cabinet (C)
9 Claw
x3
0 SP sheet
qa Connector: CN601
qs D901, LCD901
DSC-W5/W7/W15/W17
2-3 2-4
SW-001
Batery holder
Connection cord (DK-2AA)
(1-830-351-11)
FFC-051
Control switch block
SY-001 board
Lens block
D901, LCD901
(Note)
Color monitor
A/V cable (Note)
AC power
adaptor
AC IN
1
1
3
1
4
5
qa
0
9
9
qs
2
6
7
8
1
2
3
4
9
5
7
8
0
6
3
4
1
2
Note: If the A/V cable is connected to the AV OUT (MONO) jac k
of SY-001 board, the image can not appear on the LCD
screen.
If you want to confirm the circuit of LCD drive or LCD,
disconnect the A/V cable.
2-2. SY-001 BOARD SERVICE POSITION
DSC-W5/W7/W15/W17
2-5 2-6
2-3. EXCHANGE METHOD OF BARRIER ASSY
Service parts
Part Number Part Name Quantity
1 3-091-427-01 Ring (A), Ornamental 1
2 X-3954-476-1 Barrier Assy 1
3 3-086-156-31 Tapping screw (P2) 2
Tools used
Torque driver
Soldering iron
Weight about 60g
Adhesive (Super X) (Note)
Note: Use adhesive (Super X) or an equivalent article.
Don’t use what becomes white after drying like a quick-drying glue.
2-3-1. PEEL OFF OLD ORNAMENTAL RING A
The Ornamental Ring A has adhered to the Barrier Assy strongly and accordingly, use a soldering iron to weaken the adhesive force.
Heat four circled portions with the soldering iron.
Heating temperature is about 300ºC.
Beware of a burn since the entire Ornamental Ring becomes hot.
* As the adhesive force of Ornamental Ring A is considerably large, the forced peeling will damage the group-1 frame.
Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize the ring.
* Take extreme care so as not to damage the coated surface of the group-1 frame.
In case of difficult peeling, heat the ring again with the soldering iron.
If this re-heating failed, it may be advisable that the ring be peeled while heating the portions 1 → 2 → 3 → 4 in the under figure one
by one sequentially.
* Discard the removed Ornamental Ring A.
1
2
3
1
Tip
3
4
2
2-3-2. REMOVE OLD BARRIER ASSY
1 Remove two screws.
* Discard the removed screws.
2 Remove the Barrier Assy.
* Discard the removed Barrier Assy.
* After removing the Barrier Assy, if the “G1 Dust-Proof Ring” was removed, it must be returned to the home position.
In returning the ring, adjust the location of a projection to the lens direction.
This is an important part to prevent the dust and light from coming in.
* After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel.
2-3-3. INSTALL NEW BARRIER ASSY
1 Install new Barrier Assy by paying attention to the projection of the Barrier Assy in relation to the position shown in the under figure.
2 Tighten two screws.
* Tightening torque = 0.5 kgf (4.9 N)
1
1
2
Projection
2
2
1
2-7
DSC-W5/W7/W15/W17
2-3-4. ADHERE THE ORNAMENTAL RING A
Apply an adhesive to four recesses on the top surface of the Barrier Assy.
* Do not apply too much adhesive. (Make quantity of adhesives into the quantity in which a groove hides.)
Meeting a “notch” of the Ornamental Ring A with a “projection” of the group-1 frame, push the Ornamental Ring A into the group-1 frame.
* The projection of the spring for preventing static electricity must be tilted.
Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does not float up until the adhesive hardens.
Note: Be careful not to give a shock.
* After the weight was put, no gap must be present in full circumference between Ornamental Ring A and group-1 frame.
A gap, if present, causes the crackle sound NG.
* The weight must push in the Ornamental Ring A only.
If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up.
Completion after 30 minutes.
Notch
Adhesive
Adhesive
Adhesive
Do not put the weight on a black mold part.
Not gap in full circumference.
Adhesive
Projection
2-8E
DSC-W5/W7/W15/W17
2-4. CIRCUIT BOARDS LOCATION
SW-001
SY-001
(including CP201
(CH-168 board))
CD-545 flexible (W5/W15)/
CD-546 flexible (W7/W17)
Board Name Function
CD-545 flexible CCD IMAGER
CD-546 flexible CCD IMAGER
CH-168 CCD SIGNAL PROCESS
(included in SY-001)
SW-001 CONTROL SWITCH
SY-001 CAMERA MODULE, CAMERA DSP, CPU,
(including CP-201 LENS DRIVE, BURST FLASH, SDRAM, AND FLASH
,
(CH-168 board))
LCD DRIVE,
AUDIO, VIDEO, DC/DC CONVERTER,
FLASH DRIVE, CONNECTOR
DSC-W5/W7/W15/W17
Link
Link
3. BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (2/2)
POWER BLOCK DIAGRAMOVERALL BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/2)
POWER BLOCK DIAGRAMOVERALL BLOCK DIAGRAM (1/2)
DSC-W5/W7/W15/W17
3-1. OVERALL BLOCK DIAGRAM (1/2)
3-1 3-2
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3. BLOCK DIAGRAMS
LENS
IRIS
(METER)
CCD
IMAGER
IC101
CD-545/546 FLEXIBLE BOARD (1/2)
SY-001 BOARD (1/2)
17
19
86
133
CAMERA MODULE
(1/9)
SAN AUOUT
V LINE OUT
FC BRK A,
FC DIR A,
FC DIR B
48
MCK TG
XCS FE, XCS TG
XSAN RST OUT
XSAN RST OUT
XSAN RST OUT
VSUB CONT
47
CP201
22
ı
35
126
ı
129
23
25
24
F2
E1
R23
33
42
51
66
101
120
IRIS
MOTOR
M
LENS BLOCK
FC SENS
2
OVERALL (2/2)
(PAGE 3-3)
USB DP, USB DM
H26
AF4
U23
K26
L26
K5 G4 H4
L5 H2 H1
J1 J2 M5
J4 K4 M6
K2 K1
CN201
(1/2)
CD-545 : W5/W15
CD-546 : W7/W17
W5/
W15
W5/W15
W5/W15
W7/W17
W7/W17
W7/
W17
LENS TEMP
IC401
ZOOM
MOTOR
M
ZOOMFGZOOM
SENSOR
FOCUS
MOTOR
M
FOCUS
SENSOR
AC1
AD1
X201
67.5MHz
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
4
10
7
34
30
ı
28
26
ı
23
16
C1
D2
G5
H6
G4
H4
D901
BACKLIGHT
COLOR
LCD
MONITOR
K3
K1
J6
K2
B9
A10
U2
R6
A9
C9
A2
E9
B8
D9
R
G
B
CS, COM
BL H
5
3
23
24
2
6
ı
8
11
ı
14
19
ı
22
4
CN601
1
CN452
LCD901
RGT, PSIG,
HCK1, HCK2, REF,
HST, PCG, XSTBY,
DWN, EN, VCK, VST
LCD HD, LCD VD, LCD CK
LCD DRIVE
(6/9)
IC601
M
SHUTTER
MOTOR
LENS TEMP
SENSOR
24
ı
27
17
ı
20
5
ı
8
1
ı
4
29
21
CLKTGO
U4
V4
R4
E7
D7
F8
F7
R25
R5
V5
W4
MSHUT DIR,
MSHUT EN
IRIS M IN,
IRIS M EN,
IRIS S IN,
IRIS S EN
FOCUS
MOTOR
DRIVER
ZOOM
MOTOR
DRIVER
IRIS
MOTOR
DRIVER
SHUTTER
MOTOR
DRIVER
ZM BRK A,
ZM BRK B,
ZM DIR A
J25
IRIS M±, S±
Z DC MOTOR ±
F MOTOR A, A, B, B
SHUTTER ±
CN401
BUFFER
Q103
IC301
(1/2)
XCS PANEL
VIDEO AMP ON
USB DPULLUP
SAN VOUT
B1 K4 C2
D2 J4 D1
E2 F2 F1
G2 G1 H2
PANEL UNIT
31
ZM SENS 1ST
ZM DC FG 1A, 1B
LENS TEMP
F PI SENS OUT
Z PI SENS OUT
Z BOX1 PI SENS Col,
Z BOX2 PI SENS Col
IRIS M±, S±
ZOOM DC ±
FOCUS A, A, B, B
SHUTTER±
SAN AUIN
A6
B5
A4
B4
1
3
5
6
1
3
7
6
36
35
33
32
11
7 5
26
27
31
7
11
303128
29
19
135
37
48
9
6
10
13
19
10
13
17
20
113 109
112 115
125 119
118 121
6
37
5
2
4
20
19
21
36
1
3
7
8
10
11
9
12
ı
18
CAMERA DSP, CPU
LENS CONTROL,
MODE CONTROL
(2/9)
J5
46
LENS DRIVE
(3/9)
05
Q101
Q102
VIDEO AMP
(7/9)
24
1
IC802
V23
R22
AB22
Y26
T5
T23
XCS AUDIO
XAUDIO MUTE
DPULLUP ON
B3 A3
B4 B5
A5 B6
A7 B7
D8 D7
E8 E7
D6 D5
E6 B4
AB6 AC4
AE4 AE5
AC5 AF6
BL H
BL L
OVERALL (2/2)
(PAGE 3-4)
1
BL L
3
BL H
8
CN451 (1/2)CN752 (1/2)
BL L
787
B10
C10
W25
XSAN RST OUT
CA FD
H5
45
CA HD
4
8
ı
10
12
ı
15
CCD OUT
POWER SAVE
20
V2, V4, V5A, V5B,
V7, V8, V9, V10
V2, V4, V5A, V5B,
V6, V7A, V7B, V8
RG, H1B, H2B
V1, VST,
V3B, V3A
V1A, V1B,
V3A, V3B
V6
VHLD
W7/W17
W5/W15
VHLD
VST
21
VSUB
H1A, H2A
27
Q201
Q202
VSUB CONT
38
39
99
84
42
134 136
2 4
6 9 12 15
18 21 24
27 30 32
132
124
40
41
3
123
49
105
U22
Y25
B7
B8
C7
C8
G3
H2
G2
G1
P4
N4
P6
R2
B3
B1
A2
L4
L2
N5
SAN1 SO, XSAN1 SCK
SAN1 SO, XSAN1 SCK
SAN1 SO, XSAN1 SCK
CH-168 BOARD
CCD SIGNAL
PROCESSOR,
TIMING
GENERATOR
IC101
54MHz
STRB CHG
XSTRB FULL
ST UNREG
Q851
FLASH
UNIT
TRANS DRIVE,
FLASH CONTROL,
FLASH CHARGE
DETECT
(9/9)
5
7
8
6
2
IC851
XE_H
TRIG 300V
XE_L
CHARGE+
CHARGE-
+
C901
CHARGING
CAPACITOR
D851
3
5 4
1
1
T851
STRB CHG CONT
4
STRB ON
N2
P5
N6
SW-001 BOARD (1/2)
CA AD00 – CA AD13
LCD D0 – LCD D7
SAN1 SO, XSAN1 SCK
MS BS, MS D0 – MS D3, MS CLK
Q301
CPU D0 – CPU D15
CPU D0 – CPU D15
XCPU CS4
IC351
32M BURST FLASH
(4/9)
IC353
256M SDRAM
(4/9)
IC381
32M AND FLASH
(5/9)
K3 J3 G3 H7 H9 G6 G9
F7 E8
D10
D9
H8
H10
G8
G10
E7 E9 D7
E10
AB13 AA13 AE13 AF13
AF12 AE12 AA12 AC12
AC11 AB12 AE11 AF11
AE10 AB11 AC10 AB10
F7 E6 E5 G5
E4 G3 E3 G1
G7 F6 F5 F4
D5 F3 F2 E2
E8 D8 C8 B8 A8 B7 A7
C7 A2 B2 C2 A1 B1 C1
D2 D1 D4 B6 A6 C6 B3
AF21 AF20 AE20 AB18 AB19 AC19 AB16
AE19 AF19 AF18 AE18 AA15 AC18 AC17
AB15 AE17 AF17 AE16 AB14 AC16 AC15 AE14
B5
K10AC6
XCPU CS0
E7
SAN 27M CLKO
B4
AE6
AF9
DSP QCLK
J1
DSP QCLKE
J2
A18
A17
F4
CPU A01 – CPU A21, CPU A25
CPU D0 – CPU D15
CPU A01 – CPU A21
CPU A20, A21, A25
DSP DQ00 – DSP DQ31, DSP DQM0 – DSP DQM3
DSP AQ00 – DSP AQ11, DSP QBA0, DSP QBA1
R8 N7 R9 N8 P9 M8
M7 L8 L2 M3 M2 P1
N2 R1 N3 R2 E8 D7
D8 B9 C8 A9 C7 A8
A2 C3 A1 C2 B1 D2
D3 E2 K9 K1 F8 F2
D21 D22 D20 B22 A22 A23
B23 E20 E21 B24 A24 A25
B25 C25 C26 B26 E10 A10
D10 E11 B10 A11 B11 E12
D11 D12 F12 B12 A12 E13
D13 D14 F13 B15 F14 E14
G8 G9 F7 F3 G1
G2 G3 H1 H2 J3
G7 H9 J7 H8
D17 D18 D16 B18 A19
B19 E16 D19 E19 E17
B20 A20 B21 A21
DSC-W5/W7/W15/W17
3-3 3-4
3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
DPULLUP ON
SY-001 BOARD (2/2)
AUDIO AMP
(7/9)
IC801
E6
D1
B6
05
MIC901
V LINE OUT
SAN AUOUT
SAN AUIN
XCS AUDIO
XAE LOCK LED
XSTRB LED
E5
E4
SP901
SPEAKER
V LINE OUT
MIC SIG
CN802
CN801
2
OVERALL (1/2)
(PAGE 3-2)
MODE
DIAL
S001
(SHUTTER)
POWER
CONTROL SWITCH BLOCK
S002
1
XPWR ON XPWR ON
MODE DIAL0, 1 MODE DIAL0, 1
L22
L25
5
XPWR LED
D001
(POWER)
USB DP, USB DM
DC/DC
CONVERTER
(8/9)
IC001
D 3.1V
ST UNREG
PANEL 8.5V
EVER 3.0V
MS VCCV
A 3.1V
D 1.8V
CAM 2.9V
CAM –7.5V/–8.0V
CAM 15V
D 1.2V
CAM –0.5V
M 5V
SAN1 SO, XSAN1 SCK
F3
E3
CN753
XAV JACK IN
USB VBUS
XMS IN
SAN0 SI, SAN0 SO, XSAN0 SCK
A9
A8
X001
32.768kHz
S456 – 458,
454, 460
KEY AD0
KEY AD1
KEY AD0
KEY AD1
CN752
(2/2)
A5
A2
U25
AV OUT
(MONO)
3
2
(USB)
CN751
J751
1
ı
7
10
ı
16
9
8
7
10
XAE LOCK ON
XSHTR ON
XAE LOCK SW
XSHUTTER SW
CN001
+
−
BT901
BATTERY
TERMINAL
BATT UNREG
BATT GND
A6
X301
12MHz
VCC
INT
XAUDIO MUTE
F1
E22
D23
E4
K23
F22
F9
OVERALL (1/2)
(PAGE 3-2)
1
BL L
C7
AA23
XPWR OFF
W23
XCS DD
A6
T25
Y4
MS PWR ON
D3
B10
C9
E9
A4
BL H
D702
FLASH/
RECORDING
D703
(AE/AF LOCK)
2
1
1
2
D±
MS BS, MS D0 – MS D3, MS CLK MS BS, DATA0 – DATA3, SCLK
MEMORY
STICK
2
ı
5
7
8
6
CN705
6
CN451
(2/2)
6
XACCESS LED XACCESS LED
1
1
55
L23
N21
P23
BT701
LITHIUM
BATTERY
FUNCTION
KEY
S451 – 453,
455, 459
FUNCTION
KEY
AU LINE OUT
XAV JACK IN
SP±
D456
(MS ACCESS)
B7
K25
BATT SENS
G5
R26
XDD RST OUT
A7
B8
H1
CN201
(2/2)
39
D104
SELF TIMER/
AF ILLUMINATOR
XAF LEDXAF LED
CD-545/546 FLEXIBLE
BOARD (2/2)
CD-545 : W5/W15
CD-546 : W7/W17
SW-001 BOARD (2/2)
IC301
(2/2)
FRONT CONTROL
(2/9)
C6
C5
B6
AA5
AB5
Y5
W7/W17
Loading...