Sony CXP872P48A Datasheet

CXP872P48A

CMOS 8-bit Single Chip Microcomputer

Description

The CXP872P48A is a CMOS 8-bit microcomputer
which consists of A/D converter, serial interface,
timer/counter, time base timer, vector interruption,
high precision timing pattern generation circuit, PWM
generator, PWM for tuner, VISS/VASS circuit, 32kHz
timer/event counter, remote control receiving circuit,
general purpose prescaler, HSYNC counter, VCR
vertical sync separation circuit and the measuring
circuit which measure signals of capstan FG and
drum FG/PG and other servo systems, as well as
basic configurations like 8-bit CPU, PROM, RAM and
I/O port. They are integrated into a single chip.

Also this IC provides sleep/stop function which
enables to lower power consumption and ultra-low
speed instruction mode in 32kHz operation.

The CXP872P48A is the on-chip PROM version of
the CXP87248A with on-chip mask ROM, providing
the function of being able to write directly into the
program. It is suitable for evaluation use during
system development and for small quantity production.

100 pin QFP (Plastic) 100 pin LQFP (Plastic)

Structure

Silicon gate CMOS IC

Features

• A wide instruction set (213 instructions) which covers various types of data

— 16-bit arithmetic instruction/multiplication and division instruction/boolean bit operation instruction

• Minimum instruction cycle During operation 333ns/12MHz (3.0 to 5.5V)

During operation 250ns/16MHz (4.5 to 5.5V)
During operation 122µs/32kHz

• Incorporated PROM capacity 48 Kbytes

• Incorporated RAM capacity 1376 bytes

• Peripheral functions

— A/D converter 8 bit, 12-channel, successive approximation system

(Conversion time 20.0µs/16MHz)

— Serial interface Incorporated buffer RAM (1 to 32 bytes auto transfer) 1-channel

Incorporated 8-bit and 8-stage FIFO
(1 to 8 bytes auto transfer) 1-channel

— Timer 8-bit timer

8-bit timer/counter
19-bit time base timer
32kHz timer/counter

— High precision timing pattern generator PPG 19-pin 32-stage programmable

RTG 5-pin, 2-channel

— PWM/DA gate output PWM 12-bit, 2-channel

(Repetitive frequency 62kHz/16MHz)

DA gate pulse output 13-bit, 4-channel
— Servo input control Capstan FG, Drum FG/PG, CTL input
— VSYNC separator
— FRC capture unit Incorporated 26-bit and 8-stage FIFO
— PWM output 14-bit, 1-channel
— VISS/VASS circuit Pulse duty auto detection circuit
— Remote control receiving circuit 8-bit pulse measuring counter, 6-stage FIFO
— General purpose prescaler 7-bit (SYNC1 input frequency divided, FRC capture possible)
— HSYNC counter 12-bit event counter (counts SYNC1 input)

• Interruption 22 factors, 15 vectors, multi-interruption possible

• Standby mode SLEEP/STOP

• Package 100-pin plastic QFP/LQFP

Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.

– 1 –

E94813-ST

CXP872P48A

Vss

DD

V
MP

RST
XTAL

EXTAL
TX

TEX

PE1/INT2
PI4/INT1/NMI

PE0/INT0

AVss

PA0 to PA7

PB0 to PB7

8

PORT A8PORT B8PORT C

CLOCK

GENERATOR/

SYSTEM CONTROL

SPC700

CPU CORE

NMI

2

RAM

PC0 to PC7

PD0 to PD7

PE0/CKOUT

8

PORT D

RAM

1376 BYTES

ROM

48K BYTES

INTERRUPT CONTROLLER

2

FIFO

PE0 to PE1

PE2 to PE7

2

6

PORT E

2

2

2

PF4 to PF7

PF0 to PF3

4

PG0 to PG7

PH0 to PH7

4

PORT F8PORT G8PORT H7PORT I

32kHz

PRESCALER/

TIME BASE TIMER

TIMER/COUNTER

FIFO

FRC

CAPTURE UNIT

3

FIFO

PI1 to PI7

REALTIME

2

PJ0 to PJ7
8

PORT J

1

CH

PULSE

CH0

GENERATOR

RAM

PATTERN

GENERATOR

PROGRAMMABLE

4

2

PC7/RTO7

5

19

to

PC3/RTO3

PC2/PPO18

to

PA0/PPO0

AV

REF

AV

DD

AN0 to AN3

Block Diagram

A/D CONVERTER

SERIAL

12

SI0

CS0

PF0/AN4

PF7/AN11

to

SERIAL

INTERFACE UNIT

SCK0

PI7/SI1

PI6/SO1

(CH1)

PI5/SCK1

(CH0)

INTERFACE UNIT

SO0

8 BIT TIMER 1

8 BIT TIMER/COUNTER 0

PE1/EC

VSYNC SEPARATOR

PG5/SYNC1

PG4/SYNC0

PI3/TO/DDO

PG7/EXI1

PG6/EXI0

– 2 –

CONTROL

SERVO INPUT

CTL

DRUM

CAPSTAN

PG1/DFG

PG0/CFG

PG2/DPG

PG3/PBCTL

VISS/VASS

REMOCON INPUT

PI1/RMC

14 BIT PWM GENERATOR

PI2/PWM

HSYNC COUNTER

12 BIT PWM GENERATOR CH1

12 BIT PWM GENERATOR CH0

PE6/DAB0

PE4/DAA0

PE3/PWM1

PE2/PWM0

PROGRAMMABLE PRESCALER

PE7/DAB1

PE5/DAA1

PI3/ADJ

PE1/HCOUT

Pin Assignment 1 (Top View) 100-pin QFP package

PA6/PPO6

PA5/PPO5

PA4/PPO4

PA3/PPO3

PA2/PPO2

PA1/PPO1

PA0/PPO0

PB7/PPO15

PB6/PPO14

DD

V

Vpp

PA7/PPO7

CXP872P48A

SS

TX

V

TEX

PI2/PWM

PI1/RMC

PI5/SCK1

PI4/INT1/NMI

PI3/TO/DDO/ADJ

PB5/PPO13
PB4/PPO12
PB3/PPO11
PB2/PPO10

PB1/PPO9

PB0/PPO8
PC7/RTO7
PC6/RTO6
PC5/RTO5
PC4/RTO4
PC3/RTO3

PC2/PPO18
PC1/PPO17
PC0/PPO16

PJ7
PJ6
PJ5
PJ4
PJ3
PJ2
PJ1

PJ0
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0

100

99

98

1

2
3
4
5
6
7
8
9

10

11
12
13
14
15
16
17

18
19

20

21

22

23

24
25

26

27

28
29
30

32

31

33

95

93

94

96

97

35

36

34

92

37

38

39

91

40

90

41 42

89

88

87

43

44

84

86

85

46

45

47

81

82

83

80
79
78
77
76

75

74
73
72
71
70
69
68
67
66
65
64
63
62
61
60

59

58
57
56

55

54
53
52
51

49

48

50

PI6/SO1
PI7/SI1
PE0/INT0/CKOUT
PE1/EC/INT2/HCOUT
PE2/PWM0
PE3/PWM1
PE4/DAA0
PE5/DAA1
PE6/DAB0
PE7/DAB1
PG0/CFG
PG1/DFG
PG2/DPG
PG3/PBCTL
PG4/SYNC0
PG5/SYNC1
PG6/EXI0
PG7/EXI1
AN0
AN1
AN2
AN3
PF0/AN4
PF1/AN5
PF2/AN6
PF3/AN7
AV

DD

AVREF
AVSS
PF4/AN8

PH7

PH6

PH5

PH4

PH3

PH2

PH1

PH0

MP

RST

SS

V

XTAL

CS0

EXTAL

SI0

SO0

Note) 1. Vpp (Pin 90) is always connected to VDD.

2. VSS (Pins 41 and 88) are both connected to GND.

– 3 –

SCK0

PF6/AN10

PF7/AN11

PF5/AN9

Pin Assignment 2 (Top View) 100-pin LQFP package

Vpp

PA7/PPO7

PA6/PPO6

PA5/PPO5

PA4/PPO4

PA3/PPO3

PA2/PPO2

PA1/PPO1

PA0/PPO0

PB7/PPO15

PB6/PPO14

PB5/PPO13

PB4/PPO12

CXP872P48A

SS

DD

V

TX

V

TEX

PI2/PWM

PI1/RMC

PI5/SCK1

PI4/INT1/NMI

PI3/TO/DDO/ADJ

PI7/SI1

PI6/SO1

PE0/INT0/CKOUT

PB3/PPO11
PB2/PPO10

PB1/PPO9
PB0/PPO8
PC7/RTO7
PC6/RTO6
PC5/RTO5
PC4/RTO4

PC3/RTO3
PC2/PPO18
PC1/PPO17
PC0/PPO16

PJ7
PJ6
PJ5
PJ4
PJ3
PJ2
PJ1

PJ0
PD7
PD6
PD5
PD4
PD3

100

99

98

1

2
3
4
5
6
7
8
9

10
11
12
13
14
15
16
17
18
19

20
21
22

23

24
25

27

28

26

95

93

94

96

97

30

31

29

92

32

33

34

89

88

91

90

35

36

87

37

38

39

84

86

85

40

41

42

81

82

83

43

80

78

79

46

45

44

47

76

77

75
74
73
72
71
70

69

68

67

66
65
64
63
62

61

60

59

58

57

56

55

54
53
52
51

49

48

50

PE1/EC/INT2/HCOUT
PE2/PWM0
PE3/PWM1
PE4/DAA0
PE5/DAA1
PE6/DAB0
PE7/DAB1
PG0/CFG
PG1/DFG
PG2/DPG
PG3/PBCTL
PG4/SYNC0
PG5/SYNC1
PG6/EXI0
PG7/EXI1
AN0
AN1
AN2
AN3
PF0/AN4
PF1/AN5
PF2/AN6
PF3/AN7
AV

DD

AVRE

PD2

PD1

PD0

PH7

PH6

PH5

PH4

PH3

PH2

PH1

PH0

MP

RST

V

XTAL

CS0

EXTAL

SI0

SS

Note) 1. Vpp (Pin 88) is always connected to VDD.

2. VSS (Pins 39 and 86) are both connected to GND.

– 4 –

SO0

SCK0

PF6/AN10

PF7/AN11

PF4/AN8

PF5/AN9

SS

AV

Pin Description

Symbol I/O Description

(Port A)

PA0/PPO0

to

PA7/PPO7

PB0/PPO8

to

PB7/PPO15

Output/Real time
output

Output/Real time
output

8-bit output port.
Data is gated with PPO
contents by OR-gate and
they are output. (8 pins)

(Port B)
8-bit output port.
Data is gated with PPO
contents by OR-gate and
they are output. (8 pins)

Programmable pattern generator (PPG)
output. Functions as high precision real
time pulse output port.
(19 pins)
PB0 and PB2 can be 3-state controlled
with PPG.

CXP872P48A

PC0/PPO16

to

PC2/PPO18

PC3/RTO3

to

PC7/RTO7

PD0

to

PD7

PE0/INT0/
CKOUT

PE1/EC/
INT2/HCOUT

PE2/PWM0
PE3/PWM1
PE4/DAA0
PE5/DAA1
PE6/DAB0
PE7/DAB1
AN0 to AN3
PF0/AN4

to

PF3/AN7
PF4/AN8

to

PF7/AN11

I/O/Real time
output

I/O/Real time
output

I/O

Input/Input/Output

Input/Input/Input/
Output

Output/Output
Output/Output
Output/Output
Output/Output
Output/Output
Output/Output
Input

Input/Input

Output/Input

(Port C)
8-bit I/O port, enables to
specify I/O by bit unit.
Data is gated with PPO or
RTO contents by OR-gate
and they are output.
(8 pins)

Real time pulse generator (RTG) output.
Functions as high precision real time pulse
output port. (5 pins)
PC3 can be 3-state controlled with RTG.

(Port D)
8-bit I/O port.
Enables to specify I/O by 4-bit unit.
Enables to drive 12 mA sink current.
(8 pins)

Input pin to request external interruption.
Active when falling edge.

System clock frequency division output.

(Port E)
8-bit port.
Lower 2 bits

External event
input pin for
timer/counter.

Input pin to request
external interruption.
Active when falling
edge.

are input port
and upper 6
bits are output

PWM output pins.

(2 pins)
port.
(8 pins)

DA gate pulse output pins.

(4 pins)

Analog input pins to A/D converter. (12 pins)
(Port F)

Lower 4 bits are input port and upper 4 bits are
output port.
Lower 4 bits also serve as standby release input pins.
(8 pins)

Output pin for
HSYNC counter
matching signal.

SCK0
SO0
SI0
CS0

I/O
Output
Input
Input

Serial clock (CH0) I/O pin.
Serial data (CH0) output pin.
Serial data (CH0) input pin.
Serial chip select (CH0) input pin.

– 5 –

Symbol I/O Description

CXP872P48A

PG0/CFG
PG1/DFG
PG2/DPG

PG3/PBCTL
PG4/SYNC0

PG5/SYNC1
PG6/EXI0
PG7/EXI1

PH0 to PH7

PI1/RMC
PI2/PWM
PI3/TO/

DDO/ADJ
PI4/INT1/

NMI
PI5/SCK1

Input/Input
Input/Input
Input/Input

Input/Input
Input/Input

Input/Input
Input/Input
Input/Input

Output

I/O/Input
I/O/Output
I/O/Output/Output

/Output
I/O/Input/Input
I/O/I/O

Capstan FG input pin.
Drum FG input pin.
Drum PG input pin.

(Port G)
8-bit input

Playback CTL pulse input pin.
External event input pin of timer/counter.

port.
(8 pins)

Composite sync signal input pin.

External input pin to FRC capture unit.

(Port H)
8-bit output port; Medium withstand voltage (12V) and high current
(12 mA), N-ch open drain output.
(8 pins)

Remote control receiving circuit input pin.
14-bit PWM output pin.

(Port I)
7-bit I/O port.
Enables to
specify I/O by
bit unit.
(7 pins)

Timer/counter, CTL duty detection, 32kHz oscillation
adjustment output pin.

Input pin to request external interruption and
non-maskable interruption. Active when falling edge.

Serial clock (CH1) I/O pin.
PI6/SO1
PI7/SI1

PJ0 to PJ7

EXTAL
XTAL

TEX
TX

RST
MP
AVDD

AVREF
AVss
VDD

Vpp

I/O/Output
I/O/Input

I/O

Input
Output

Input
Output

Input
Input

Input

Serial data (CH1) output pin.

Serial data (CH1) input pin.

(Port J)
8-bit I/O port. Function as standby release input can be specified by
bit unit. Enables to specify I/O by bit unit.

Connection pin of crystal oscillator for system clock. When supplying
the external clock, input the external clock to EXTAL pin and input
opposite phase clock to XTAL pin.

Connection pin of crystal oscillator for 32kHz timer clock. When used
as event counter, input to TEX pin and leave TX pin open.
(Feedback resistor is not removed.)

System reset pin of active "L" level.
Microprocessor mode input pin. Always connect to GND.
Positive power supply pin of A/D converter.

Reference voltage input pin of A/D converter.
GND pin of A/D converter.
Positive power supply pin.
Positive power supply pin used for writing incorporated PROM.

Connect to VDD during normal operation.

Vss

GND pin. Connect both VSS pins to GND.

– 6 –

A

Input/Output Circuit Formats for Pins

CXP872P48A

Pin

PA0/PPO0

to

PA7/PPO7
PB4/PPO12

to

PB7/PPO15

12 pins

PB0/PPO8
PB2/PPO10

Port A
Port B

Data bus

PPO data

Port A or Port B

RD (Port A or Port B)

PPO8 or PPO10

PB0 or
PB2 data

RD (Port B)

Circuit format

Output becomes active from high impedance by
data writing to port register.

When reset

Hi-Z

Hi-Z

2 pins

PB1/PPO9
PB3/PPO11

2 pins

Data bus

Output becomes active from high impedance
by data writing to port register.

PPO9 or PPO11

PPG control status
register bit 0
3-state control
selection

AAA

PPO9 or PPO11

PB1 or
PB3 data

Data bus

RD
(Port B)

Output becomes active
from high impedance by
data writing to port register.

Hi-Z

– 7 –

CXP872P48A

Pin

PC0/PPO16

to

PC2/PPO18
PC5/RTO5

to

PC7/RTO7

6 pins

PC3/RTO3

Port C

Data bus

Data bus

Data bus

PPO, RTO data

Port C data

Port C direction

RD (Port C)

RD (Port C direction)

RTO3

PC3 data

PC3 direction

Circuit format

(Every bit)

Input
protection
circuit

IP

IP

When reset

Hi-Z

Hi-Z

1 pin

PC4/RTO4

1 pin

RD (Port C)

Data bus

RD (Port C direction)

RTG interruption control
register
bit 7
3-state control selection

AAA

RTO4

PC4 data

PC4 direction

Data bus

RD (Port C)

Data bus

RD (Port C direction)

RTO4

Hi-Z

IP

RTO data is OR-gate data of ch0 and ch1.

– 8 –

CXP872P48A

A

Pin

PD0

to

PD7

8 pins

Port D

Port D data

Port D direction

Data bus

RD (Port D)

Port E

Port E/PWM
selection register
bit 0, 1

AAA

Circuit format

When reset

High current
12mA

Hi-Z

IP

(Every 4 bits)

PD0 to 3
PD4 to 7

PE0/INT0
/CKOUT

1 pin

PE1/EC/INT2
/HCOUT

Data bus

Port E

From HSYNC
counter

RD (Port E)

Hi-Z control

HCOUT

Data bus

PS1
PS2
PS3

Interruption circuit

RD (Port E)

MPX

IP

Input
protection
circuit

IP

Input
protection
circuit

Hi-Z

Hi-Z

1 pin

To interruption
circuit/event counter

– 9 –

CXP872P48A

A

A

Pin

PE2/PWM0
PE3/PWM1
PE4/DAA0
PE5/DAA1

4 pins

PE6/DAB0
PE7/DAB1

Port E

Hi-Z control

Data bus

Port E

Hi-Z control

DA gate output or
PWM output

Port E data

Port/DA output
select

RD (Port E)

DA gate output

Port E data

Circuit format

MPX

A

MPX

A

When reset

Hi-Z

H level

2 pins

AN0

to

AN3

4 pins

PF0/AN4

to

PF3/AN7

4 pins

Data bus

Port F

Port/DA output
select

RD (Port E)

Input multiplexer

IP

Input multiplexer

IP

RD (Port F)

A/D converter

Hi-Z

A/D converter

Hi-Z

Data bus

– 10 –