Sony CDX - M 600650 SERVICE MANUAL

CDX-M600/M600R/M650
SERVICE MANUAL
Photo: CDX-M600
• The tuner and CD sections have no adjustments.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (CDX-M600/M650)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION 19 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 1% total harmonic distortion.
Other Specifications CD player section
System Compact disc digital audio
Signal-to-noise ratio 90 dB Frequency response 10 – 20,000 Hz Wow and flutter Below measurable limit Laser Diode Properties (CDX-M600/M650)
Material GaAlAs Wavelength 780 nm Emission Duration Continuous Laser output power Less than 44.6 µW*
* This output is the value measured at a distance
of 200 mm from the objective lens surface on the Optical Pick-up Block.
Tuner section
FM
Tuning range 87.5 – 107.9 MHz (CDX-M600R)
Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 8 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 66 dB (stereo),
Harmonic distortion at 1 kHz
Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz
AM (CDX-M600/M650)
Tuning range 530 – 1,710 kHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV
system
87.5 – 108.0 MHz (CDX-M600/M650)
72 dB (mono)
0.6% (stereo),
0.3% (mono)
FM/MW/LW COMPACT DISC PLAYER
US Model
CDX-M600/M650
AEP Model
UK Model
Model Name Using Similar Mechanism NEW CD Drive Mechanism Type MG-383Z-121//K Optical Pick-up Name KSS-720A
MW/LW (CDX-M600R)
Tuning range MW: 531 – 1,602 kHz
LW: 153 – 279 kHz Aerial terminal External aerial connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW: 30 µV
LW: 40 µV
Power amplifier section
Outputs Speaker outputs Speaker impedance 4 – 8 ohms Maximum power output 50 W × 4 (at 4 ohms)
General
Outputs Audio outputs (3) (CDX-M600/M650)
Audio outputs (2) (CDX-M600R)
Power antenna relay
control lead (CDX-M600/M650)
Power aerial relay
control lead (CDX-M600R)
Power amplifier control
lead Inputs Telephone ATT control
lead
Illumination control lead Power requirements 12 V DC car battery
(negative ground)
– Continued on next page –
FM/AM COMPACT DISC PLAYER
CDX-M600/M650
CDX-M600R
1
Dimensions Approx. 178 × 50 × 182 mm
Mounting dimensions Approx. 182 × 53 × 163 mm
Mass Approx. 1.5 kg (3 lb. 1 oz.) Supplied accessories Card remote commander
Design and specifications are subject to change without notice.
(7
1/8 × 2 × 7 1/4 in.)
(w/h/d)
(7
1/4 × 2 1/8 × 6 1/2 in.)
(w/h/d)
RM-X93 (CDX-M600) RM-X94 (CDX-M650) RM-X96 (CDX-M600R) Parts for installation and connections (1 set)
SERVICE NOTE
CAUTION
Use of controls or adjustments or performance of proce­dures other than those specified herein may result in haz­ardous radiation exposure.
NOTE FOR THE OPENING OF THE FRONT PANEL
In this set, the front panel is lowered to below the bottom face when it is opened. When servicing the set, place it on a stand having a height of about 2 cm.
stand
Notes on Chip Component Replacement
Never reuse a disconnected chip component.
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick­up block. Therefore, when checking the laser diode emission, ob­serve from more than 30 cm away from the objective lens.
MODEL IDENTIFICATION
CDX-M600R have 3 type models.
– MODEL NUMBER LABEL –
MODEL No. CDX-M600R
FM/MW/LW COMPACT DISC PLAYER
Part No.
Part No. Model 3-046-059-0s TYPE1 3-046-060-0s TYPE2 3-047-827-0s TYPE3
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE P ART NUMBERS APPEAR AS SHOWN IN THIS MANU AL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
TABLE OF CONTENTS
1. GENERAL
Location of controls................................................................. 4
Getting Started......................................................................... 5
Setting the clock ...................................................................... 5
CD Player CD/MD Unit .......................................................... 6
Radio ....................................................................................... 7
RDS ......................................................................................... 9
DAB....................................................................................... 10
Other Functions ..................................................................... 11
TV/Video ...............................................................................13
Connections ........................................................................... 14
2. DISASSEMBLY
2-1. Front Panel Assy (Normal)................................................ 21
2-2. Front Panel Assy (Inoperative).......................................... 21
2-3. CD Mechanism Block, Flexible Board ............................. 22
2-4. Sub Panel (CD) Sub Assy ................................................. 22
2-5. Motor Block Assy, Cam (R) Assy ..................................... 23
2-6. Main Board ....................................................................... 23
2-7. Heat Sink ........................................................................... 24
2-8. Chassis (T) Sub Assy ........................................................ 24
2-9. Lever Section..................................................................... 25
2-10. Servo Board....................................................................... 25
2-11. Shaft Roller Assy .............................................................. 26
2-12. Floating Block Assy .......................................................... 26
2-13. Optical Pick-up Block ....................................................... 27
3. PHASE ALIGNMENT
3-1. Arm (A-L) Assy, Arm (B-L) Assy..................................... 28
3-2. Cam (L) ............................................................................. 28
3-3. Motor Block ...................................................................... 29
3-4. Alignment between Arm (A-L) Assy
and Arm (B-L) Assy .......................................................... 29
3-5. Arm (A-R) Assy, Arm (B-R) Assy .................................... 30
3-6. Cam (R) ............................................................................. 30
4. DIAGRAMS
4-1. IC Pin Descriptions ........................................................... 31
4-2. Block Diagram –CD Section–........................................... 40
4-3. Block Diagram –Tuner Section–....................................... 41
4-4. Block Diagram –Display Section–.................................... 42
4-5. Circuit Boards Location .................................................... 43
4-6. Printed Wiring Boards –CD Mechanism Section–............ 44
4-7. Schematic Diagram –CD Mechanism Section (1/2)– ....... 46
4-8. Schematic Diagram –CD Mechanism Section (2/2)– ....... 47
4-9. Printed Wiring Boards –Main Section– ............................ 48
4-10. Schematic Diagram –Main Section (1/4)– ........................ 50
4-11. Schematic Diagram –Main Section (2/4)– ........................ 51
4-12. Schematic Diagram –Main Section (3/4)– ........................ 52
4-13. Schematic Diagram –Main Section (4/4)– ........................ 53
4-14. Printed Wiring Board –Sub Section– ................................ 54
4-15. Schematic Diagram –Sub Section– ................................... 55
4-16. Printed Wiring Board –Display Section– .......................... 56
4-17. Schematic Diagram –Display Section–............................. 57
5. EXPLODED VIEWS
5-1. Chassis Section ................................................................. 60
5-2. Front Panel Section ........................................................... 61
5-3. CD Mechanism Section (1) ............................................... 62
5-4. CD Mechanism Section (2) ............................................... 63
5-5. CD Mechanism Section (3) ............................................... 64
6. ELECTRICAL PARTS LIST ........................................ 65
3
CDX-M600R
SECTION 1
GENERAL
This section is extracted from instruction manual.
CDX-M600/M650
4
567
CDX-M600R
CDX-M600/M650
8
CDX-M600R
9
CDX-M600R
10
111213
CDX-M600/M650
CDX-M600R
14
151617
CDX-M600/M650
18
192021
SECTION 2
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
2-1. FRONT PANEL ASSY (NORMAL)
1 Turn on the power and open the front panel.
4 screw (panel)
5 spacer (arm)
6 front panel assy
(Take care not to pull the flexible board excessively.)
2-2. FRONT PANEL ASSY (INOPERATIVE)
0 Lift the motor block assy slightly to make a play.
3 screw (panel)
4 spacer (arm)
7 PTT 2.6x6
8 PTT 2.6x6
3 spacer (arm)
flexible board
stand
2 screw (panel)
5 PTT 2.6x6
6 PTT 2.6x6
qa
qs front panel assy
(Take care not to pull the
flexible board excessively.)
9 Lift the cam (R) assy
slightly to make a play.
1 screw (panel)
2 spacer (arm)
flexible board
2-3. CD MECHANISM BLOCK, FLEXIBLE BOARD
5 CD mechanism block
3 PTT 2.6x4
7 bracket (CD)
6 PTT 2.6x6
8 cover (flexible)
0 flexible board
9 CNP802
Note: When installing
the flexible board, make the board slack
as illustrated.
1 PTT 2.6x6
2-4. SUB PANEL (CD) SUB ASSY
4 claw
3 PTT 2.6x6
2 PTT 2.6x4
4 CNP701
1 CNP805
22
6 sub panel (CD) sub assy
5 claw
2 PTT 2.6 x6
2-5. MOTOR BLOCK ASSY, CAM (R) ASSY
Note : Install the motor block assy and cam (R) assy in this roder.
For phase alignment between cams (L) and (R), see page 28 and 30.
5 motor block assy
3 CNP902
4 PTT 2.6x6
1 PTT 2.6x6
2 cam (R) assy
Note: Install the cam (R) assy with the cam fully rotated in the direction of the arrow A.
A
2-6. MAIN BOARD
6 MAIN board
5 PTT 2.6x6
ground point
4 PTT 2.6x6 ground point
3 PTT 2.6x8
2 PTT 2.6x8
1 PTT 2.6x8
23
2-7. HEAT SINK
5 heat sink
4 PTT 2.6x8
3 PTT 2.6x8
2 PTT 2.6x12
1 PTT 2.6x8
2-8. CHASSIS (T) SUB ASSY
1 Unsolder the lead wires.
2 P 2x3
3 P 2x3
4 chassis (T) sub assy
black red
white
24
Loading...
+ 54 hidden pages