Sony CDX-L400X User Manual

SERVICE MANUAL
Ver 1.0 2001. 12
• The tuner and CD sections have no adjustments.
SPECIFICATIONS
AEP Model
UK Model
Model Name Using Similar Mechanism CDX-L350/L360
CD Drive Mechanism Type MG-393X-121//Q
Optical Pick-up Name KSS-720A
CD player section
Signal-to-noise ratio 90 dB Frequency response 10 – 20,000 Hz Wow and flutter Below measurable limit
Tuner section
FM
Tuning range 87.5 – 108.0 MHz Aerial terminal External aerial connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 8 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 66 dB (stereo),
72 dB (mono)
Harmonic distortion at 1 kHz
0.6% (stereo),
0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz
MW/LW
Tuning range MW: 531 – 1,602 kHz
LW: 153 – 279 kHz Aerial terminal External aerial connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW: 30 µV
LW: 40 µV
Power amplifier section
Outputs Speaker outputs
(sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 45 W × 4 (at 4 ohms)
General
Outputs Audio outputs
Power aerial relay control
lead Inputs Telephone ATT control lead Tone controls Bass ±9 dB at 100 Hz
Treble ±9 dB at 10 kHz Power requirements 12 V DC car battery
(negative ground) Dimensions Approx. 178 × 50 × 177 mm
(w/h/d) Mounting dimension Approx. 182 × 53 × 162 mm
(w/h/d) Mass Approx. 1.2 kg Supplied accessories Parts for installation and
connections (1 set)
Front panel case (1)
Design and specifications are subject to change without notice.
9-873-438-01
2001L0400-1
© 2001. 12
FM/MW/LW COMPACT DISC PLAYER
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation
1
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable) as shown below.
Connect the MAIN board (CNP301) and the SERVO board (CN1) with the extension cable (Part No. J-2502-011-1).
CDX-L400X
MAIN BOARD CNP301
SERVO BOARD CN1
J-2502-011-1

TABLE OF CONTENTS

1. GENERAL
Location of controls ................................................................. 4
Notes on CD-R/CD-RW discs ................................................. 4
Connections ............................................................................. 5
2. DISASSEMBLY
2-1. Sub Panel Assy .................................................................... 6
2-2. CD Mechanism Block ......................................................... 7
2-3. Main Board ......................................................................... 7
2-4. Heat Sink ............................................................................. 8
2-5. Chassis (T.U) Assy .............................................................. 8
2-6. Disc in Board ...................................................................... 9
2-7. Servo Board ......................................................................... 9
2-8. Arm Roller Assy ................................................................ 10
2-9. Chassis (OP) Assy ............................................................. 10
2-10. Optical Pick-up Block ....................................................... 11
3. DIAGRAMS
3-1. IC Pin Description ............................................................. 12
3-2. Circuit Boards Location .................................................... 14
3-3. Block Diagram –CD Section– ........................................... 15
3-4. Block Diagram –Tuner Section– ....................................... 16
3-5. Block Diagram –Display Section– .................................... 17
3-6. Printed Wiring Boards –CD Mechanism Section– ............ 18
3-7. Schematic Diagram –CD Mechanism Section– ................ 20
3-8. Printed Wiring Board –Main Section– .............................. 21
3-9. Schematic Diagram –Main Section (1/2)– ........................ 22
3-10. Schematic Diagram –Main Section (2/2)– ........................ 23
3-11. Printed Wiring Board –Key Section– ................................ 24
3-12. Schematic Diagram –Key Section–................................... 25
4. EXPLODED VIEWS
4-1. Chassis Section ................................................................. 28
4-2. Front panel Section ........................................................... 29
4-3. CD Mechanism Section (1) ............................................... 30
4-4. CD Mechanism Section (2) ............................................... 31
4-5. CD Mechanism Section (3) ............................................... 32
5. ELECTRICAL PARTS LIST......................................... 33
3
CDX-L400X
SECTION 2

DISASSEMBLY

Note : This set can be disassemble according to the following sequence.
SET
2-5. CHASSIS (T.U) ASSY
2-1. SUB PANEL ASSY
(Page 6)
(Page 8)
2-2. CD MECHANISM BLOCK
(Page 7)
2-3. MAIN BOARD
(Page 7)
2-4. HEAT SINK
(Page 8)
2-6. DISC IN BOARD
(Page 9)
2-8. ARM ROLLER ASSY
(Page 10)
2-9. CHASSIS (OP) ASSY
(Page 10)
2-10. OPTICAL PICK-UP BLOCK
(Page 11)
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL ASSY
2-7. SERVO BOARD
(Page 9)
2
PTT 2.6x6
1
PTT 2.6x6
3
claw
5

sub panel assy

4
claws
6
2-2. CD MECHANISM BLOCK
6
6
5

CD mechanism block

2
PTT 2.6x6
7
bracket (CD)
6
PTT 2.6x
CDX-L400X
2-3. MAIN BOARD
5
ground point screws
(PTT 2.6x6)
3
6

MAIN board

4
CNP301
4
ground point screw
(PTT 2.6x6)
1
PTT 2.6x6
3
PTT 2.6x
1
PTT 2.6x6
2
PTT 2.6x6
7
CDX-L400X
0
2-4. HEAT SINK
4

heat sink

3
PTT 2.6x1
2-5. CHASSIS (T.U) ASSY
1 Unsolder the lead wires.
2 P 2x3
1
PTT 2.6x10
2
PTT 2.6x16
3 P 2x3

4 chassis (T.U) assy

black red white
8
2-6. DISC IN BOARD
5
guide (disc)
3
tension spring (LR)
1
PS 2x4
2

DISC IN board

CDX-L400X
2-7. SERVO BOARD
3 Removal the solders.
4
8 PS 2x4
5 P 2x3
claws
7 PS 2x4
2 CN2
1 CN3

9 SERVO board

4 Removal the solders.
6 loading motor assy
(M903)
9
CDX-L400X
)
2-8. ARM ROLLER ASSY
When installing, take note of the positions
arm (roller) and washers. (Fig. 1)

2 arm roller assy

3 PS 2x3
4 LOAD board
retaining ring (roller)
arm
bearing (roller)
washer(RA)
Fig. 1
washer(RA)
bearing (roller
arm
2-9. CHASSIS (OP) ASSY
8 compression spring (FL)
1 tension spring (KF1)
1 tension spring (RA3)

7 chassis (OP) assy

9 compression spring (FL)
2 tension spring (KR1)
5 Fit lever (D) in the
direction of the arrow.
10
6 Turn loading ring in the direction of the arrow.
3 damper (T)
4 damper (T)
2-10. OPTICAL PICK-UP BLOCK
1
P 2x3
2
sled motor assy
7
shaft (feed) assy
5
P 2x3
6
plate spring (feed)
3

optical pick-up block

CDX-L400X
4
pick-up flexible board
11
CDX-L400X
SECTION 3

DIAGRAMS

3-1. IC PIN DESCRIPTION
• IC501 MN101C49KTD2 (SYSTEM CONTROL)
Pin No. Pin Name I/O Pin Description
1 VREF– Rated voltage – for A/D converter.
2 VSM I S-meter voltage detection input
3 NC Not used. (Connect to ground in this set)
4 KEYIN1 I Key input 1
5 KEYIN0 I Key input 0
6 RCIN0 I Rotary commander input 0 (Fixed at L in this set)
7 QUALITY I Noise detection input
8 MPTH I Tuner multi-path detection input
9 NC Not used. (Connect to ground in this set)
10 VREF+ Rated voltage + for A/D converter. (+5 V)
11 VDD Power supply pin (+5 V)
12 OSCOUT O Oscillator output (18.432 MHz)
13 OSCIN I Oscillator input (18.432 MHz)
14 VSS Ground
15 XIN I Oscillator input (32.768 kHz)
16 XOUT O Oscillator output (32.768 kHz)
17 MMOD Mode selector (Connect to ground in this set)
18 LCDSO O LCD serial data output
19 LCDCE O LCD chip enable output
20 LCDCKO O LCD serial clock output
21 CD_TSO O CD text serial data output
22 CD_TSI I CD text serial data input
23 CD_TCKO O CD text serial clock output
24 NC Not used. (Open)
25 NC Not used. (Open)
26 KEY ACK I Key acknowledge detection input
27 DAVN I RDS data block synchro detection input
28 BUIN I Back-up power detection input
29 NC I Not used. (Connect to ground in this set)
30 CD_SELFSW I CD self switch input
31 CD_PACK I CD pack synchro signal input
32 NC (VCC) Not used. (Connect to VDD in this set)
33 RESET I Reset input
34 NC Not used. (Fixed at H in this set)
35 BEEP O Beep output
36 NC Not used. (Open)
37 TESTIN I Test mode detection input
38 ACCIN I Accessory power detection input
39 NC (VCC) Not used. (Open)
40 TELATT I Telephone attenuate detection input
41 NC (VCC) Not used. (Connect to VDD in this set)
42 UNISO O SONY BUS data output
43 UNISI I SONY BUS data input
44 UNICKO O SONY BUS clock output
45 I2C_SIO I/O I2C BUS serial data input/output
46 NC Not used. (Open)
47 I2C_CKO O I2C BUS serial clock output
48 NC Not used. (Open)
49 TUNON O Tuner power control output
50 PW_ON O System power control output
51 TSTB O CD text strobe output
12
Loading...
+ 18 hidden pages