HCD-GR5/RX50 is the tuner, deck, CD
and amplifier section in MHC-GR5/RX50.
Photo: HCD-GR5
Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol a are trademarks
of Dolby Laboratories Licensing Corporation.
CD
SECTION
TAPE
DECK
SECTION
Model Name Using Similar MechanismHCD-H551
CD Mechanism TypeCDM28-5BD19
Base Unit TypeBU-5BD19
Optical Pick-up TypeKSS-213BA/F-NP
Model Name Using Similar MechanismHCD-H551
T ape Transport Mechanism T ypeTCM-220WR2E
AEP Model
UK Model
HCD-RX50
E Model
Tourist Model
HCD-GR5
CD player section
SystemCompact disc and digital
audio system
LaserSemiconductor (λ = 780nm)
Emission duration:
continuous
Laser outputMax 44.6 µW*
*This output is the value
measured at a distance of
200mm from the objective
lens surface on the Optical
Pick-up Block with 7mm
aperture.
Wavelength780 – 790 nm
Frequency response
2 Hz – 20 kHz (±0.5 dB)
Signal-to-noise ratio
More than 90 dB
Dynamic range More than 90 dB
CD DIGITAL OPTICAL OUTPUT
(Square optical connector jack,rear panel)
Wavelength600nm
Output level-18dBm
T uner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
East European model:
65.0 – 75.0 MHz,
87.5 – 108.0 MHz
SPECIFICATIONS
Tourist model:
76.0 – 108.0 MHz
Other models:
87.5 – 108.0 MHz
AerialFM lead aerial
Aerial terminals 75 ohm unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
AEP, UK, East European models:
MW: 531 – 1,602 kHz (with
the interval set at 9 kHz)
LW: 153 – 279 kHz (with
the interval set at 3 kHz)
German models:
531 – 1,602 kHz (with
the interval set at 9 kHz)
EA4,Thailand models:
531 – 1,710 kHz(with
the interval set at 9 kHz)
530 – 1,710 kHz(with
the interval set at 10 kHz)
— Continue on next page —
COMPACT DISC DECK RECEIVER
MICROFILM
— 1 —
Page 2
Other models:
MW: 531 – 1,602 kHz (with
the interval set at 9 kHz)
MW: 530 – 1,710 kHz (with
the interval set at 10 kHz)
SW: 5.95 – 17.90 MHz
(with the interval set at 10 kHz)
AntennaAM loop antenna,
External antenna terminals
Intermediate frequency
450 kHz
Amplifier section
(AEP,UK,German,East European models)
DIN power output
40W+40W (6 ohms, at
1kHz, DIN)
Continuous RMS power output
50W+50W (6 ohms, at
1kHz, 10% THD)
Music power output
85W+85W (6 ohms, at
1kHz, 10% THD)
(Other models)
Peak music power output
800W
Continuous RMS power output
50W+50W (6 ohms, at
1kHz, 10% THD)
General
Power requirements
AEP,UK,German,East European models:
220 – 230 V AC, 50/60 Hz
EA4,Thailand models:
220 – 240 V AC, 50/60 Hz
Other models:
110 – 120 V, 220 – 240 V
AC, 50/60 Hz
Adjustable with the voltage selector
Power consumption
95 W
DimensionsApprox. 280 x 330 x 360 mm
(11 1/8 x 13 x 14 1/4 in)
(w/h/d)
incl. projecting parts and
controls
MassApprox. 7.5 kg (16 lb 9 oz)
Design and specifications are subject to
change without notice.
• Abbreviation
EA4: Without voltage selector Saudi Arabia model
Inputs
MIX MIC (phone jacks):
AUDIO IN:
Outputs
PHONES (stereo phone jack):
SPEAKER: accepts impedance of 6 to
AUDIO OUT:
GR5 model:
SUPPER WOOFER:
Tape player section
Recording system
Frequency response
Wow and flutter
sensitivity 1 mV,
impedance 10 kilohms
Audio (Phono Jacks)
Voltage 450mV
Impedance 47 kilohms
accepts headphones of 8 ohms
or more.
16 ohms.
Audio (Phono Jacks)
Voltage 450mV
Impedance 1 kilohms
Voltage 1 V, impedance
1 kilohms
4-track 2-channel stereo
(DOLBY NR OFF)
40 – 13,000 Hz (±3 dB),
using Sony TYPE I cassette
40 – 14,000 Hz (±3 dB),
using Sony TYPE II cassette
0.3% W .RMS (NAB)
— 2 —
Page 3
MODEL IDENTIFICATION
— BACK PANEL —
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Parts No.
MODELPARTS No.
GR5 : E model
GR5 : EA3,Taiwan, Tourist model
GR5 : Singapore,Malaysia model
GR5 : Hong Kong model
GR5 : Indonesian model
GR5 : EA4,Thailand model
RX50 : AEP ,German model
RX50 : UK model
RX50 : East European model
• Abbreviation
EA3: With voltage selector Saudi Arabia model.
EA4: Without voltage selector Saudi Arabia model.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
This caution
label is located
inside the unit.
— 3 —
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED
LINE WITH MARK ! ON THE SCHEMA TIC DIA GRAMS AND
IN THE P ARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
8. ELECTRICAL PARTS LIST....................................79
— 4 —
Page 5
SECTION 1
SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH
TURNS OFF
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output two times.
Note for installation (ROTARY ENCODER)
Note :
When attaching the Base unit, insert the
BU cam
groove
section A into the groove of BU cam.
Section A
Note :
When attaching the BU
cam, engage the Rotary
encoder switch as shown in
the figure.
Insert a tapering driver into the
aperture of the unit bottom, and turn
in the direction of arrow.
*
To close the disc tray, turn the
driver in the reverse direction.
[FL Display Tube, LED All Lit and Key Check mode]
When the TUNER/BAND , DISPLAY , and MENU 2 buttons
are pressed simultaneously, the FL display tube and LEDs will all
light up. Press any button to enter the key check mode.
When the key check mode is entered, the FL display tube displays
“K 1 J0 V0”. Each time a button is pressed, the counter increases
in the following order, K 2 n K 3 n K 4.
If buttons already pressed once are pressed again, the counter will
not increase. When the VOLUME knob is rotated in the + direction,
the count increases in the following order.
V1 n V2 n V3.
When rotated in the–direction, it decreases in the following order.
V0 n V9 n V8.
When the AMS dial is rotated in the clockwise direction, the count
increases in the following order.
J1 n J2 n J3.
When rotated in the counterclockwise direction, it decreases in the
following order.
J0 n J9 n J8.
T o exit form the test mode, press the TUNER/BAND , DISPLA Y
, MENU 2 buttons simultaneously again.
[Switching the channel step 9 KHz/10 KHz]
Press ENTER/NEXT button and POWER button simultaneously
to switch the AM channel step 9 KHz and 10 KHz. Be sure not to
change with carelessness.
— 5 —
Page 6
SECTION 2
GENERAL
This section is extracted from
instruction manual.
Index to Parts and Controls
Refer to the pages indicated in parentheses for
details on how to use the controls.
Controls with an asterisk have indicators on
themselves.
Front Panel
!™
1
2
3
4
5
6
7
8
9
0
!¡
@∞
@§
@¶
@•
@ª
#º
#¡
#™
·
ª
·
ª
!£
^
!¢
!∞
!
§
!
¶
!•
!ª
@º
@¡
·
ª
@™
@£
@¢
#£
#¢
#∞
@•
·
ª
@ª
#º
#§
#™
1 Disc tray
2 POWER switch
3 LOOP button
4 TIMER button
5 PHONES jack
6 DISPLAY button
7 SURROUND button
8 MIX MIC jack
9 MULTI FUNCTION CONTROL buttons
0 FREQUENCY +/– buttons
!¡ JOG dial
!™ MENU 1 – 3 button
!£ § OPEN / CLOSE button
!¢ fl (play / pause) button
!∞ p (stop) button
!§ P FILE button
!¶ EFFECT ON / OFF button
!• TUNER / BAND button
!ª FUNCTION button
@º ENTER / NEXT button
@¡ GROOVE button
@™ DBFB button
@£ VOLUME control
@¢ KARAOKE PON / MPX button
@∞ HIGH SPEED DUBBING button
@§ DIRECTION button
@¶ DOLBY NR button
@• 0 / ) (rewind / fast forward) button
@ª ª / · (reverse side play /
front side play) button
#º p (stop) button
#¡ Deck A
#™ § EJECT button
#£ CD SYNCHRO button
#¢ r REC button
#∞ P PAUSE button
#§ Deck B
MULTI FUNCTION CONTROL buttons
The buttons you can operate the CD player,
tuner and the timer light up.
CD player
C DCONTINUESHUFFLEPROGRAMREPEAT
Tuner
TUNING
TUNER
MODE
TUNER
MEMORY
STEREO
MONO
Timer
TIMERCLOCK SETSELECTSLEEP
SET
Rear Panel
(AEP, UK, German, East European models)
4
1
2
3
1 MD OUT / IN jacks
2 CD DIGITAL OUT OPTICAL jack
3 SPEAKER L / R connectors
4 ANTENNA terminals
(E, EA, Hong Kong, Malaysia, Singapore,
T aiwan, T ourist, Thailand, Indonesian models)
5
1
2
3
6
4
1 MD OUT / IN jacks
2 CD DIGITAL OUT OPTICAL jack
3 SPEAKER L / R connectors
4 SUPER WOOFER jack
5 ANTENNA terminals
6 Voltage selector (except for EA4, Thailand
models)
• Abbreviation
EA4: Without v oltage selector Saudi Arabia model
— 6 —
Page 7
Display Window
Remote (RM-SD50)
1!™23 456789 0!¡
SUR 12
12 REC SLEEP
DOLBY NR
PON
TUNED MONO STEREO
B OFF
MANUAL
PRESET
RELAY
AUTO
SYNC
REC
DBFB
ALL PROGRAM
1DISK S SHUFFLE
REPEAT 1 STEP
12345
678910
11 12 13 14 15
16 17 18 19 20
khz dB
Mhz MIN
MPX
!£!¢
1 SUR indicators
2 indicator
3 Timer indicators
4 Karaoke PON / MPX indicators
5 DOLBY NR indicator
6 Tuning indicator
7 Direction mode indicators
8 DBFB indicator
9 CD playback indicators
0 Music calendar
!¡ VOLUME indicators
!™ Tuner indicators
!£ Multi display
!¢ Radio frequency / playing time / sound
frequency level indications
1
2
VOL
3
4
–
5
6
7
8
9
1 SLEEP button
2 LOOP button
3 CD button
4 TUNER / BAND button
5 DECK A / DECK B button
6 FUNCTION button
7 / button
8 MUSIC MENU ON / OFF button
9 / button
0 POWER switch
!¡ (pause) button
!™ (stop) button
2. Demagnetize the record/playback head with a head
demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
TorqueTorque meterMeter reading
FWD
FWD
back tension
REV
REV
back tension
FF/REW
FWD tension
REV tension
CQ-102C
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
36 to 61 g • cm
(0.5 - 0.84 oz • inch)
2 to 6 g • cm
(0.02 - 0.08 oz • inch)
36 to 61 g • cm
(0.5 - 0.84 oz • inch)
2 to 6 g • cm
(0.02 - 0.08 oz • inch)
61 to 143 g • cm
(0.85 - 1.99 oz • inch)
100 g or more
(3.53 oz or more)
100 g or more
(3.53 oz or more)
DECK SECTION0 dB=0.775V
1. Demagnetize the record/playback head with a head damagnetizer .
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
parts adjusted.
4. The adjustments should be performed with the rated power supply
voltage unless otherwise noted.
5. The adjustments should be performed in the order g iven in this
service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit
adjustment.)
6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwise
specified.
DOLBY NR switch: OFF
P-4-A100
WS-48B
P-4-L300
SignalTape
10 kHz, –10 dB
3 kHz, 0 dB
315 Hz, 0 dB
Used for
Azimuth Adjustment
Tape Speed Adjustment
Level Adjustment
Record/Playback Head Azimuth Adjustment
(Deck A, Deck B)
Note: Perform this adjustments for both decks.
test tape
P-4-A100
(10kHz, –10dB)
MAIN board
CN403
Pin
3
(L-CH)
Pin
1
(R-CH)
level meter
set
MAIN board
CN403
Pin
2
(GND)
+
–
— 11 —
Page 12
Procedure:
1. Mode : Playback
2. T urn the adjustment scre w and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw so
that outputs match within 1 dB of peak.
L-CH
peakoutput
screw
position
level
R-CH
peak
within
1dB
L-CH
peak
R-CH
peak
within 1dB
screw
position
3. Mode: Playback
test tape
P-4-A100
(10kHz, –10dB)
main board
CN403
Pin
set
3
(L-CH)
L
R
Pin
2
(GND)
oscilloscope
Tape Speed Adjustment (Deck A)
Note: Start the Tape Speed adjustment as below after setting the
test mode.
The tape speed can be changed with the HIGH SPEED
DUBBING button during the test mode.
Method :
1. Turn the power switch on.
2. Press the DISPLAY button, MENU 1 button and TUNER/
BAND button simultaneously.
Procedure :
Mode: Playback
test tape WS-48B
(3kHz, 0dB)
set
MAIN board
CN403 Pin
Pin
3
(L-CH)
1
(R-CH)
frequency counter
+
–
1. Insert the WS-48B into the deck A to playback.
2. Press the HIGH SPEED DUBBING button. Then at HIGH
SPEED mode.
3. Adjust the RV652 on the AUDIO board so that the frequency
counter reading becomes 6,000 ± 90 Hz.
4. Press the HIGH SPEED DUBBING button again to be set the
NORMAL SPEED mode.
5. Set to the playback mode.
6. Adjust the RV651 on the AUDIO board so that the frequency
counter reading becomes 3,000 ± 90 Hz.
Pin 1 (R-CH)
Waveform of oscilloscope
in phase
45˚
90˚
135˚180˚
wronggood
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
Adjustment Location: Playback Head (Deck A)
Record/Playback/Erase Head (Deck B)
FWD side
Adjustment screw
REV side
Frequency difference between deck A and deck B the beginning
of the tape should be within ± 1.5%.
Adjustment Location: AUDIO board
Playback Level Adjustment (Deck A, Deck B)
Procedure:
Mode: Playback
test tape P-4-L300
(315Hz, 0dB)
set
MAIN board
CN403 Pin
Pin
level meter
3
(L-CH)
1
(R-CH)
Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301
(L-CH) and RV401 (R-CH)
so that adjustment within the following adjustment level.
Adjustment level:
CN403 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB)
level differ ence between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board
— 12 —
Page 13
Record Bias Adjustment (Deck B)
Record Level Adjustment (Deck B)
Procedure:
1. Press FUNCTION button to Select MD.
2. Mode: Record
MD IN
1) 315Hz
2) 10kHz
AF OSC
attenuator
}
50 mV (–23.8 dB)
600
blank tape
CS-123
set
3. Mode: Playback
recorded
position
set
MAIN board
CN403Pin
Pin
3
(L-CH)
1
(R-CH)
level meter
4. Confirm playback the signal recorded in step 2 become
adjustment level as follows.
If these levels do not adjustment lev el, adjust the R V341 (L-CH)
and RV441 (R-CH) on the A UDIO board to repeat steps 2 and 3.
Procedure:
1. Press FUNCTION button to Select MD.
2. Mode: Record
MD IN
315Hz 50mV (–23.8 dB)
AF OSC
attenuator
600
set
blank tape
CS-123
3. Mode: Playback
recorded
portion
set
MAIN board
CN403Pin
Pin
3
(L-CH)
1
(R-CH)
level meter
4. Confirm playback the signal recorded in step 2 become
adjustment level as follows.
If these levels do not adjustment lev el, adjust the R V301 (L-CH)
and R V351 (R-CH) on the MAIN board to repeat steps 2 and 3.
Adjustment level: The playback output of 10 kHz le vel differ ence
CN403 PB level: 47.3 to 53.1 mV (–24.3 to –23.3 dB)
Adjustment Location: MAIN board
[MAIN BOARD] (Component Side)
3
1
CN403
RV351
Record Level Adjustment
(R CH)
IC401
RV301
Record Level Adjustment
(L CH)
RV351
RV301
— 13 —
Page 14
TUNER SECTION0dB=1µV
Note: 1. As a front-end (FE1) is difficult to repair if faulty, replace
it with new one.
2. No adjustment is needed due to a tuner pack.
AM Tuned Level Adjustment
Note: FM Tuned Level adjustment should be performed after this
AM Tuned Level Adjustment.
Setting:
Band: AM or MW
loop antenna
loop antenna
AM RF SSG
(Supplied accessories)
set
30% amplitude
modulation by
400Hz signal
Modulation: 999 kHz (at 9 kHz step)
1,050 kHz (at 10 kHz step)
Field strength dB (µV/m) = SSG output level dB (µV/m) –26dB.
60cm
Procedure:
1. Set the output of SSG so that the input lev el of the set becomes
55 dB.
2. Tune the set to 999 kHz or 1,050 kHz.
3. Adjust R V41 to the point (moment) when the TUNED indicator
will change from going off to going on.
Adjustment Location: TCB board
FM Tuned Level Adjustment
Note: This adjustment should be after AM Tuned Le vel Adjustment.
Setting:
Band: FM
FM RF stereo signal
generator
75
Ω
coaxial
AM antenna
terminal (TM1)
Adjustment Location:
[TCB BOARD] (Component Side)
IC41RV42
RV42
FM Tuned Level
Adjustment
RV41
AM T uned Level
Adjustment
FE1
RV41
TM1
set
Carrier frequency : 98MHz
Modulation: AUDIO 1kHz, 75kHz
Output level: 25dB (at 75
deviation (100%)
Ω
open)
FM ANTENNA terminal
(TM1)
Procedure:
1. Supply a 25 dB 98 MHz signal from the ANTENNA terminal.
2. Tune the set to 98 MHz.
3. Adjust R V42 to the point (moment) when the TUNED indicator
will change from going off to going on.
Adjustment Location: TCB board
— 14 —
Page 15
SW OSC Voltage Adjustment
(Tourist model)
Setting:
Band: SW
Adjustment Location:
[TCB BOARD] — Component Side —
Procedure:
1. Connect digital Voltmeter to diode D1 center lead and ground.
2. Adjust for a following value reading on digital voltmeter.
Reading on digital
voltmeter
1.2 ± 0.1 V
8.5 ± 0.2 V
SW
Set frequency
5.95 MHz
17.9 MHz
Adjustment
part
T2
CV2
SW T racking Adjustment
(Tourist model)
Setting:
Band: SW
AM RF SSG
30% amplitude
modulation by
400Hz signal
set
SPEAKER terminal
AM ANTENNA terminal
level meter
IC41
D1, CV2, T2
SW OSC Voltage
Adjustment
CV2
CV1
D1
T1
T2
CV1, T1
SW Tracking
Adjustment
TM1
Procedure:
Adjust for maximum reading on level meter.
Adjustment
part
T1
CV1
SW
Set frequency
7 MHz
17 MHz
• Repeat the procedures is each adjustment several times, and the
frequency coverage and tracking adjustment should be f inally done
by the trimmer capacitors.
— 15 —
Page 16
CD SECTION
Note:
1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10MΩ impedance.
4. Clean the object lens by an applicator with neutral detergent when
the signal level is low than specified value with the following
checks.
5. Adjust the focus bias adjustment when optical block is replaced.
Focus Bias Adjustment
oscilloscope
BD board
TP (RF)
TP (VC)
Procedure:
1. Connect oscilloscope to test point TP (RF).
(Ground terminal : TP (VC))
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Adjust RV101 so that the waveform is clear.
(Clear RF signal waveform means that the shape “
clearly distinguished at the center of the waveform.)
5. After adjustment, check the RF signal level.
• RF signal
VOLT/DIV: 200 mV
TIME/DIV: 500 nS
” can be
S Curve Check
Procedure :
BD board
TP (FEO)
TP (VC)
oscilloscope
1. Connect oscilloscope to test point TP (FEO).
2. Connect between test point TP (FOK) and Ground by lead wire.
3. Turn Power switch on.
4. Put disc (YEDS-18) in and turned Power switch on again and
actuate the focus search. (actuate the focus search when disc
table is moving in and out.)
5. Check the oscilloscope waveform (S-curve) is symmetrical
between A and B. And confirm peak to peak level within 2.4 ±
0.7 Vp-p.
S-curve waveform
symmetry
A
within 2.4 ± 0.7 Vp-p
B
6. After check, remove the lead wire connected in step 2.
Note: • Try to measure several times to make sure than the ratio of
A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the
brightness to obtain best waveform.
level: 1.3 ± 0.3 Vp-p
RF Level Check
Procedure :
oscilloscope
BD board
TP (RF)
TP (VC)
1. Connect oscilloscope to test point TP (RF) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that oscilloscope wa veform is clear and check RF signal
level is correct or not.
Note: Clear RF signal waveform means that the shape “
” can be
clearly distinguished at the center of the waveform.
RF signal waveform
VOLT/DIV: 200 mV
TIME/DIV: 500 nS
level: 1.3 ± 0.3 Vp-p
— 16 —
Page 17
E-F Balance Check
Adjustment Location:
oscilloscope
BD board
TP (TEO)
TP (VC)
Procedure:
1. Connect test point TP703 (ADJ2) on MAIN board to Ground
with a lead wire.
2. Connect oscilloscpe to test point TP (TEO).
3. Turned Power switch on.
4. Put disc (YEDS-18) in and playback.
5. Confirm that the oscilloscope waveform is symmetrical on the
top and bottom in relation to 0Vdc, and check this level.
Traverse waveform
A
0V
B
level: 300 ± 100 mVp-p
Specified level: • x 100 = less than ± 7%
A – B
2 (A + B)
• A + B = 300 ± 100 mVp-p
[BD BOARD] — Component Side —
RV103
IC104
RV101
TEO
VC
RF
IC101
TEI
FEO
RV102
GND
FOK
FEI
PCK
[MAIN BOARD] — Conductor Side —
IC102
6. Remove the lead wire connected in step 1.
Focus/Tracking Gain Adjustment (RV102, RV103)
This gain has a margin, so even if it is slightly off.
There is no problem.
Therfore, do not perform this adjustment.
Please note that it should be fixed to mechanical center position
when you moved and do not know original position.
IC701
TP703
(ADJ2)
— 17 —
Page 18
HCD-GR5/RX50
6-1 BLOCK DIAGRAMS
- CD SECTION -
SECTION 6
DIAGRAMS
OPTICAL PICK-UP BLOCK
DETECTORK
E
A
B
LASER
DIODE
M102
SLED MOTOR
M101
SPINDLE MOTOR
M
M
D
C
F
B+
FOCUS
26
.
27
1
.
2
COIL
A
D
C
B
TRACKING
SLED / SPINDLE
MOTOR DRIVE
IC102 (2 / 2)
SLED MOTOR
DRIVE
SPINDLE MOTOR
DRIVE
COIL
10
2-AXIS
DEVICE
CD
DIGITAL OUT
IC200
OPTICAL
IC103
SQS0
CLOCK
SCOR
53
46
47
43
LOADING MOTOR DRIVER
2
OUT1
M
10
OUT2
XTAI
PCMD
LRCK
BCLK
XRST
SENS
SQCK
50
49
S291 LOAD OUT
S292 LOAD IN
IC201
39
DOUT
DIGITAL SIGNAL
PROCESSOR
CLV SERVO
MDP
DATA
52
3
51
M903
LOADING MOTOR
3
XLAT
IC101 (1/2)
FOCUS/TRACKING SERVO
EFM COMPARATOR
RV101
FOCUS
BIAS
14
55
54
1
56
57
59
B+
Q103
FOCUS SW
RF
CNIN
SEIN
FOK
DATAO
XLTO
CLKO
1
4
2
5
6
TRACKING
Q101,102
LD DRIVE
T-
T+
F-
F+
25
4
RV102
FOCUS
GAIN
RV103
GAIN
35
RF1
36
PD2
F
38
39
E
2
FE1
1
FEO
42
TEO
44
TEI
LD
33
PHD
34
25
XRESET
18
TRACKING
COIL DRIVE
17
FOCUS / TRAKING
COIL DRIVE
IC102 (1 / 2 )
12
FOCUS
COIL DRIVE
11
SLED
SERVO
IC101 (2 / 2)
16
SLOSL+
7
C,OUT
SENS
DATA
FE BIAS
FE-M
TA-M
XRST
RFO
FOK
XLT
CLK
FE-O
TA-O
FGD
31
23
24
25
21
20
19
37
6
7
12
13
4
19
9
14
344
21
20
223
IN1
IN2
X101
16.9344MHz
5 • 6
XTI
CKO
2
DATA
1
LRCK
BCLK
L OUT
R OUT
DATA
26 28 27
5
6
DIGITAL FILTER
D/A CONVERTER
XTO
16
13
MLAT
CLOCK
CD CLK
CD DATA
DF LAT
SCOR
SQ DATA
SQ CLK
SENS
FOCUS SW
XRST
XLAT
OUT SW
IN SW
LOAD IN
LOAD OUT
IC104
L-CH
R-CH
C
MAIN
SECTION
(page 19)
— 18 —
• R CH:Same as L CH
• SIGNAL PATH
:CD
:digidal out
Page 19
— MAIN SECTION —
J801
MD
(AUDIO)
IN
L
PB L
REC L
PLAY REC/PB
A SHUT
B SHUT
B HALF
A HALF
A PLAY
B PLAY
PB A/B
NORM/HIGH
BIAS ON/OFF
B
RM ON/OFF
DECK
NR ON/OFF
SECTION
(Page 23)
TUNER
SECTION
SECTION
(Page 18)
AEP,UK,G,EE MODEL : (Page 21)
*
JE MODEL : (Page 22)
(*)
CD
A
C
REC/PB
PAS/DOL
LM ON/OFF
CAP M H/L
A TRG
B TRG
TRIG H/L
CAP M ON/OFF
ST L
COM DATA
COM CLK
COM DIN
STEREO
TUNED
ST CE
MUTE
L CH
SCOR
DF LAT
SENS
X RST
CD CLK
CD DATA
FOCUS SW
SQ CLK
SQ DATA
X LAT
OUT SW
IN SW
LOAD IN
LOAD OUT
J601
MIX
MIC
IC802 INPUT SELECTOR
v
TC
ST
CD
DA
CK
1
2
4
5
55
TC RELAY
A SHUT
56
57
B SHUT
58
B HALF
59
A HALF
60
220 A PLAY
61
220 B PLAY
80
TC A
81
NORM
BIAS OFF
82
83
REC MUTE
NR OFF
84
85
PB
86
PASS AMP/DOLBY
87
LINE MUTE ON
CAP M HIGH
88
89
A TRG
90
B TRG
TRG LOW
91
92
CAP M ON
COM DATA
73
71
COM CLK
COM DIN
72
93
STEREO
94
TUNED
95
ST CE
10
ST MUTE ON
SCOR
25
DF LAT
29
30
SENS
31
XRST
38
CD CLK
CD DATA
40
43
FOCUS SW
SQ CLK
44
SQ DATA
45
X LAT
46
20
OUT-SW-OPEN
IN SW
16
LOAD IN
21
LOAD OUT
22
3
B
A
INH
IC601
MIC AMP
167
3
9
10
6
71
29
28
30
IC701
MASTER CONTROL
MICON
INTERFACE
32 33 34
CK
DA
62
62427 LAT
6564
R-CH
+
4544
–
EQ
IC901
EQUALIZER/VOLUME
6240 41
62
POWER ON
67
77
DBFB HIGH
MUTE
70
X501
5MHz
REQ GM
13
CLK MG
14
DATA GM
15
16
DATA MG
RDY MG
46
RESET
34
X1
X2
35
GR1-12SEG1-22
7 - 1 • 80 - 76 75 - 72 • 70 - 53
FLUORESCENT INDICATOR TUBE
GM REQ
34
35
MG CLK
36
GM DATA
37
MG DATA
MG RDY
32
4
RESET
817
AC CUT
XOUT
2
3
XIN
XOUT
5
XIN
6
68
CD POWER
D705
RESET
SWITCH
IC702
RESET
+5.6V
X701
10MHz
X702
32kHz
Q701
43
IC501
GRAPHIC
CONTROL
FL501
4238
BB12
BB22
Q901
DBFB
SWITCH
LED1
LED4
LED9
LED13
LED SELECT
SIRCS IN
JOG A
JOG B
KEY4
|
KEY1
VOL A
VOL B
HCD-GR5/RX50
EXCEPT AEP,UK,G,EE
J201
SUPER
WOOFER
+
R-CH
IC1201
POWER AMP
1
10
+7.5V
+5.6V
D +5V
D +5V
(CD)
Q1201
OVER LOAD
DET
+
R-CH
R-CH
Q502,503
D704
+5V
D706
+5V
D1018
Q1001,1002
CD POWER
ON/OFF
Q1204
+
D +5V
D1016,1017
D1021,1022
TC +5V
+7.5V
-7.5V
ST +10V
VF DP
• R CH:Same as L CH
• SIGNAL PATH
R-CH
+
+10V REG
-25V REG
: FM
: PB
: REC
: CD
: MD
Q954
MUTE
Q820
MUTE
SWITCH
Q902
FEED
BACK
43
|
Q504
40
Q507-511
••
10
Q601-603
•
LED
9
•
DRIVE
51
|
49
Q501
19
47
45
31
28
|
25
44
12
VF
LED
CONTROL
IC502
REMOTE
CONTROL
RECEIVER
S562
MULTI JOG
STATION
ROTARY
ENCODER
KEY
MATRIX
S561
VOLUME
ROTARY
ENCODER
D579,583
D585-590
D601,611,621
RY1201
6
2
IC1202
PROTECTOR
1
7
4
Q1205
PROTECTOR
SWITCH
Q1206
STANDBY
SWITCH
IC1003
+7V REG
IC1002
+7V REG
D1097
|
IC1001
D1099
+5V REG
RECT
IC1004
-7V REG
Q1003
Q1006
+B
-B
• Abbreviation
: German model.
G
: East European model.
EE
: Without voltage selector Saudi Arabia model.
EA4
: Thailand model.
TH
: Tourist model.
JE
Q1207
RELAY DRIVE
Q1208
HP/SP
SWITCHING
D1309,1310
D1003
|
D1006
RECT
D1001
RECT
D1013
D1014
RECT
D1250
RECT
VF
RECT
POWER TRANSFORMER
+B
T1601
EXCEPT AEP,UK,G,EE,EA4,TH
R-CH
VS1601
VOLTAGE
SELECTOR
TM1201
SPEAKER
+
-
J501
PHONES
AC -IN
– 19 –
– 20 –
Page 20
HCD-GR5/RX50
— TUNER SECTION —
(AEP,UK,German,East European MODEL)
VSS
XOUT
XIN
RESET
XOUT
XIN
GND (test)
AC CUT
SUPER WOOFER ON
ST-MUTE ON
180-A-PLAY
180-B-PLAY
180-B-REC
CLK CHK
UP-SW
IN-SW
ENCODER-0
ENCODER-1
ENCODER-2
OUT SW OPEN
LOAD IN
LOAD OUT
TBL-L
TBL-R
SCOR
TBL-SENS
RDS INT
RDS DATA
DF LAT
SENS
XRST
MG-RDY
ADJ
GM-REQ
MG-CLK
GM-DATA
MG-DATA
CD-CLK
ADJ-2
CD-DATA
FunctionI/O
–
Ground
O
X’tal (10 MHz).
I
I
Reset signal input.
O
X’tal for clock (32.768 KHz).
I
–
Ground
I
Back up signal input.
O
Not used. (Connected to ground)
O
Mute signal output for tuner.
I
I
Tape detection signal input. (Not used) (Connected to ground)
I
Not used. (Pull up)
I
Disc table up detect. (Not used) (Connected to ground)
I
Loading in detection signal input.
I
I
I
Disctray address detect encoder input. (Not used) (Connected to ground)
I
I
Loading out detection signal input.
O
Loading motor control signal output.
O
O
Table motor control signal output. (Not used) (Open)
O
I
Sub-code sync signal input.
I
CD Table sensor signal input. (Not used) (Connected to ground)
I
RDS data start input. (Not used) (Connected to ground)
O
RDS data start output. (Not used) (Connected to ground)
AUB IN
AUB OUT
FOCUS SW
SQ-CLK
SQ-DATA
X-LAT
TEST
VAREF
VA
SS
VSS
VDD
SPEC
DESTINATION
DISC SENS
TC RELAY
A-SHUT
B-SHUT
B-HALF
A-HALF
220-A-PLAY
220-B-PLAY
62427 LAT
K-CON-LAT
VOL LAT (AV)
REAR SP RELAY B
FRONT SP RELAY C
POWER ON
CD POWER
PROLOG LAT
MUTE
COM CLK
COM DIN
COM DATA
K CON ON
LIDDED LED
PROLOG ON
DBFB-HIGH
URG STB STDBY
URG STB ON
TC A
I
Audio bus in/output. (Not used) (Open)
O
O
Focus switching signal output.
O
Subcode Q data read clock output.
I
Subcode Q data input.
O
Latch signal digital signal processor.
I
Test land.
I
Analog reference voltage input.
–
Ground
–
+5V
–
I
Destination detection setting input.
I
I
Not used. (Connected to ground)
O
REC/PB select signal output.
I
I
I
Control signal input from deck.
I
I
I
PLL latch output.
O
Not used. (Open)
O
Latch signal for electrical volume. (Not used) (Open)
O
O
Not used. (Open)
O
Power on signal output.
O
CD power control signal output.
O
Not used. (Open)
O
Mute signal for AMP.
O
PLL clock output.
O
PLL data input.
I
PLL data output.
O
Not used. (Open)
O
Disc No. LED drive signal output. (Not used) (Open)
NORM
BIAS OFF
REC MUTE
NR OFF
PB
P ASS. AMP/DOLBY
LINE MUTE ON
CAP. M-HIGH
A-TRG
B-TRG
TRG LOW
CAP M ON
STEREO
TUNED
ST-CE
DELAY SEL MIC
DELAY ON
DELAY LEVEL A
DELAY LEVEL B
V
seldom required for routine service. Some delay
should be anticipated when ordering these items.
• The mechanical parts with no reference number in
the exploded views are not supplied.
• Hardware (# mark) list and accessories and pac king
materials are given in the last of this parts list.
• Color Indication of Appearrance Parts
Example:
KNOB, BALANCE (WHITE)
↑
Cabinet's Color
7-1. CASE SECTION
2
1
• Abbreviation
G : German model
EE : East European model
EA3: With voltage selector Saudi Arabia model
EA4: Without voltage selector Saudi Arabia model
MY : Malaysia model
SP : Singapore model
HK : Hong Kong model
TH : Thailand model
TW : Taiwan model
IA : Indonesian model
JE : T ourist model
3
#1
4
5
The components identified by
mark ! or dotted line with mark !
are critical for safety.
Replace only with part number
specified.
* 53A-4386-430-A MAIN BOARD,COMPLETE (AEP,UK)
* 53A-4386-432-A MAIN BOARD,COMPLETE (JE)
* 53A-4386-433-A MAIN BOARD,COMPLETE (G)
* 53A-4386-434-A MAIN BOARD,COMPLETE (E,EA3,MY,SP,HK,TW)
* 53A-4386-436-A MAIN BOARD,COMPLETE (EE)
* 53A-4386-437-A MAIN BOARD,COMPLETE (IA)
* 53A-4386-439-A MAIN BOARD,COMPLETE (EA4,TH)
* 544-988-833-01 PANEL, BACK (E)
* 544-988-833-11 PANEL, BACK (EA3,TW,JE)
* 544-988-833-21 PANEL, BACK (SP,MY)
* 544-988-833-31 PANEL, BACK (HK)
* 544-988-833-41 PANEL, BACK (IA)
* 544-988-833-51 PANEL, BACK (EA4,TH)
* 544-988-834-01 PANEL, BACK (AEP,G)
* 544-988-834-11 PANEL, BACK (UK)
* 544-988-834-21 PANEL, BACK (EE)
554-956-370-12 BAND, PLUG FIXED (UK,HK)
The components identified by
mark ! or dotted line with mark !
are critical for safety.
Replace only with part number
specified.
3553-928-047-01 PULLEY, TENSION
3563-908-601-01 SPRING (REV LEVER),TORSION
3573-908-599-01 LEVER (REV-A)
3583-908-603-01 LEVER (TRIGGER A)
359X-3370-108-1 FLYWHEEL (BF) ASSY
3603-908-605-01 SPRING (TRIGGER), TORSION
3613-908-609-01 GEAR, TRIGGER
3623-913-845-11 BELT (A)
3633-913-846-11 BELT (FR)
not supplied
369
354
#8
353
#7
351
352
Ref. No.Part No.DescriptionRemark
364X-3370-171-1 FLYWHEEL (BR) ASSY
3653-908-600-01 LEVER (REV-B)
* 3661-650-669-11 LEAF SWITH BOARD
3673-908-598-01 CAM (B)
368X-3372-931-1 ARM (B) ASSY,FR
3693-914-111-01 SPRING (FR), TORSION
3703-908-604-01 LEVER (TRIGGER B)
3713-911-115-01 WASHER, STOPPER
3723-917-176-11 BELT (B)
373X-3370-172-1 FLYWHEEL (AF) ASSY
374X-3371-441-1 CHASSIS ASSY, MECHANICAL
* 375A-2007-435-A AUDIO BOARD, COMPLETE
M1X-3371-223-1 MOTOR ASSY (CAPSTAN)
M2A-2004-410-A MOTOR ASSY, DC (TRIGGER)
— 78 —
Page 51
SECTION 8
ELECTRICAL PARTS LIST
Note:
The components identified by
mark ! or dotted line with mark !
are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board
name.
• Abbreviation
G: German model
EE : East European model
EA3 : With voltage selector Saudi Arabia model
EA4 : W ithout voltage selector Saudi Arabia model
MY : Malaysia model
SP : Singapore model
HK : Hong Kong model
TH : Thailand model
TW : Taiwan model
IA : Indonesian model
JE: Tourist model
R1021-216-001-00 METAL CHIP105%1/10W
R1031-216-049-91 METAL GLAZE1K5%1/10W
R1041-216-097-91 METAL GLAZE100K5%1/10W
R1051-216-093-00 METAL CHIP68K5%1/10W
R1061-216-093-00 METAL CHIP68K5%1/10W
R1071-216-093-00 METAL CHIP68K5%1/10W
R1081-216-093-00 METAL CHIP68K5%1/10W
R1091-216-097-91 METAL GLAZE100K5%1/10W
R1121-216-083-00 METAL CHIP27K5%1/10W
R1131-216-083-00 METAL CHIP27K5%1/10W
R1141-216-101-00 METAL CHIP150K5%1/10W
R1151-216-101-00 METAL CHIP150K5%1/10W
R1161-216-061-00 METAL CHIP3.3K5%1/10W
R1171-216-069-00 METAL CHIP6.8K5%1/10W
R1181-216-049-91 METAL GLAZE1K5%1/10W
R1191-216-089-91 METAL GLAZE47K5%1/10W
R1201-216-089-91 METAL GLAZE47K5%1/10W
R1211-216-114-00 METAL GLAZE510K5%1/10W
R1221-216-097-91 METAL GLAZE100K5%1/10W
R1231-216-099-00 METAL CHIP120K5%1/10W
R1241-216-091-00 METAL CHIP56K5%1/10W
R1251-216-069-00 METAL CHIP6.8K5%1/10W
R1261-216-063-91 METAL GLAZE3.9K5%1/10W
R1271-216-089-91 METAL GLAZE47K5%1/10W
The components identified by
mark ! or dotted line with mark !
are critical for safety.
Replace only with part number
specified.
R1291-216-049-91 METAL GLAZE1K5%1/10W
R1301-216-079-00 METAL CHIP18K5%1/10W
R1311-216-079-00 METAL CHIP18K5%1/10W
R1321-216-061-00 METAL CHIP3.3K5%1/10W
R1331-216-061-00 METAL CHIP3.3K5%1/10W
R1341-216-065-00 METAL CHIP4.7K5%1/10W
R1351-216-065-00 METAL CHIP4.7K5%1/10W
R1361-216-073-00 METAL CHIP10K5%1/10W
R1371-216-065-00 METAL CHIP4.7K5%1/10W
R1381-216-049-91 METAL GLAZE1K5%1/10W
R1391-216-033-00 METAL CHIP2205%1/10W
R1401-216-081-00 METAL CHIP22K5%1/10W
R1411-216-061-00 METAL CHIP3.3K5%1/10W
R1421-216-061-00 METAL CHIP3.3K5%1/10W
R1431-216-121-91 METAL GLAZE1M5%1/10W
R1441-216-073-00 METAL CHIP10K5%1/10W
R1451-216-097-91 METAL GLAZE100K5%1/10W
R1461-216-097-91 METAL GLAZE100K5%1/10W
R1471-216-049-91 METAL GLAZE1K5%1/10W
R1481-216-049-91 METAL GLAZE1K5%1/10W
R1491-216-049-91 METAL GLAZE1K5%1/10W
R1501-216-037-00 METAL CHIP3305%1/10W
R1511-216-037-00 METAL CHIP3305%1/10W
R1521-216-037-00 METAL CHIP3305%1/10W
R1531-216-082-00 METAL GLAZE24K5%1/10W
R1541-216-065-00 METAL CHIP4.7K5%1/10W
R1561-216-085-00 METAL CHIP33K5%1/10W
R1571-216-069-00 METAL CHIP6.8K5%1/10W
R1581-216-001-00 METAL CHIP105%1/10W
(EXCEPT AEP,UK,G,EE,IA)
J5011-774-728-11 JACK (PHONES) (IA)
J5011-770-226-11 JACK (LARGE TYPE)(PHONES)(AEP,UK,G,EE)
J6011-778-605-11 JACK (LARGE TYPE)(MIX MIC)
(EXCEPT AEP,UK,G,EE,IA)
J6011-774-728-11 JACK (MIX MIC) (IA)
J6011-770-226-11 JACK (LARGE TYPE)(MIX MIC)(AEP,UK,G,EE)
*A-4386-430-A MAIN BOARD, COMPLETE (AEP,UK)
*A-4386-432-A MAIN BOARD, COMPLETE (JE)
*A-4386-433-A MAIN BOARD, COMPLETE (G)
*A-4386-434-A MAIN BOARD, COMPLETE
(E,EA3,MY,SP,HK,TW)
*A-4386-436-A MAIN BOARD, COMPLETE (EE)
*A-4386-437-A MAIN BOARD, COMPLETE (IA)
*A-4386-439-A MAIN BOARD, COMPLETE (EA4,TH)
IC4018-759-289-38 IC HA12195NT
IC4028-759-822-09 IC LB1641
IC7018-759-451-82 IC TMP87CS64YF-6521
IC7028-759-165-80 IC PST600C-T
IC8028-759-000-48 IC MC14052BCP
IC9018-759-331-39 IC M62427FP
IC1001 8-759-231-53 IC TA7805S
IC1002 8-759-604-86 IC M5F7807L
IC1003 8-759-604-86 IC M5F7807L
IC1004 8-759-604-90 IC M5F7907L
IC1201 8-749-920-09 IC STK-4152MK2K
IC1202 8-759-111-68 IC uPC1237HA
FE11-233-542-11 FRONT END (4 GANG) (AEP,UK,G)
FE11-693-335-11 FRONT END (3 GANG) (EE)
FE21-233-514-11 ENCAPSULATED COMPONENT (AEP,UK,EE)
FE21-239-260-11 ENCAPSULATED COMPONENT (G)
< IC >
IC218-759-288-54 IC LC72130
IC418-759-176-03 IC LA1835
IFT411-409-636-11 TRANSFORMER, IF (CERAMIC FILTER)
< JUMPER RESISTOR >
JR11-216-295-91 METAL CHIP05%1/10W
(G)
JR21-216-295-91 METAL CHIP05%1/10W
(AEP,UK,EE)
JR31-216-295-91 METAL CHIP05%1/10W
(G)
JR61-216-295-91 METAL CHIP05%1/10W
(AEP,UK,G)
JR71-216-295-91 METAL CHIP05%1/10W
(G)
JR81-216-295-91 METAL CHIP05%1/10W
(AEP,UK,EE)
JR91-216-295-91 METAL CHIP05%1/10W
(AEP,UK,EE)
JR451-216-295-91 METAL CHIP05%1/10W
JR461-216-296-91 METAL CHIP05%1/8W
JR471-216-295-91 METAL CHIP05%1/10W
JR481-216-295-91 METAL CHIP05%1/10W
JR491-216-296-91 METAL CHIP05%1/8W
JR511-216-295-91 METAL CHIP05%1/10W
(AEP,UK,EE)
JR521-216-295-91 METAL CHIP05%1/10W
JR531-216-296-91 METAL CHIP05%1/8W
(AEP,UK,EE)
JR541-216-295-91 METAL CHIP05%1/10W
R11-249-401-11 CARBON475%1/4W
R21-216-037-00 METAL CHIP3305%1/10W
R31-216-037-00 METAL CHIP3305%1/10W
R51-216-037-00 METAL CHIP3305%1/10W
R61-216-081-00 METAL CHIP22K5%1/10W
R71-216-037-00 METAL CHIP3305%1/10W
R81-216-037-00 METAL CHIP3305%1/10W
R9
1-216-081-00 METAL CHIP22K5%1/10W
R101-216-037-00 METAL CHIP3305%1/10W
R111-216-081-00 METAL CHIP22K5%1/10W
R121-216-037-00 METAL CHIP3305%1/10W
R131-216-037-00 METAL CHIP3305%1/10W
R141-216-081-00 METAL CHIP22K5%1/10W
R181-216-073-00 METAL CHIP10K5%1/10W
(AEP,UK,EE)
R191-216-073-00 METAL CHIP10K5%1/10W
(AEP,UK,EE)
R211-216-049-91 METAL CHIP1.0K5%1/10W
R221-216-049-91 METAL CHIP1.0K5%1/10W
R231-216-049-91 METAL CHIP1.0K5%1/10W
R241-216-025-91 METAL CHIP1005%1/10W
R251-249-417-11 CARBON1K5%1/4W
R261-249-437-11 CARBON47K5%1/4W
R271-249-429-11 CARBON10K5%1/4W
R281-249-417-11 CARBON1K5%1/4W
R291-216-061-00 METAL CHIP3.3K5%1/10W
R301-216-186-00 METAL CHIP3305%1/8W
R311-216-025-91 METAL CHIP1005%1/10W
R321-249-425-11 CARBON4.7K5%1/4W
R331-249-425-11 CARBON4.7K5%1/4W
R341-216-065-00 METAL CHIP4.7K5%1/10W
R351-216-214-00 METAL CHIP4.7K5%1/8W
R361-216-025-91 METAL CHIP1005%1/10W
R371-216-073-00 METAL CHIP10K5%1/10W
R381-216-089-91 METAL CHIP47K5%1/10W
R391-249-429-11 CARBON10K5%1/4W
R421-216-073-00 METAL CHIP10K5%1/10W
R431-216-042-00 METAL CHIP5105%1/10W
R441-216-013-00 METAL CHIP335%1/10W
R451-247-843-11 CARBON3.3K5%1/4W
R461-216-073-00 METAL CHIP10K5%1/10W
R471-216-097-91 METAL CHIP100K5%1/10W
R481-249-417-11 CARBON1K5%1/4W
R491-216-049-91 METAL CHIP1.0K5%1/10W
R501-216-065-00 METAL CHIP4.7K5%1/10W
R511-216-065-00 METAL CHIP4.7K5%1/10W
R531-249-429-11 CARBON10K5%1/4W
R551-216-162-00 METAL CHIP335%1/8W
R561-249-393-11 CARBON105%1/4W
R911-216-295-91 METAL CHIP05%1/10W
JR501-216-295-91 METAL GLAZE05%1/10W
JR511-216-295-91 METAL GLAZE05%1/10W
JR521-216-295-91 METAL GLAZE05%1/10W
JR531-216-296-91 METAL GLAZE05%1/8W
JR541-216-295-91 METAL GLAZE05%1/10W
R11-249-401-11 CARBON475%1/4W
R21-216-037-00 METAL CHIP3305%1/10W
R31-216-037-00 METAL CHIP3305%1/10W
R51-216-037-00 METAL CHIP3305%1/10W
R61-216-081-00 METAL CHIP22K5%1/10W
R71-216-037-00 METAL CHIP3305%1/10W
R81-216-037-00 METAL CHIP3305%1/10W
R91-216-081-00 METAL CHIP22K5%1/10W
R101-216-037-00 METAL CHIP3305%1/10W
R111-216-081-00 METAL CHIP22K5%1/10W
R121-216-037-00 METAL CHIP3305%1/10W
R131-216-037-00 METAL CHIP3305%1/10W
R141-216-081-00 METAL CHIP22K5%1/10W
R181-216-065-00 METAL CHIP4.7K5%1/10W
R191-216-073-00 METAL CHIP10K5%1/10W
Ref. No.Part No.DescriptionRemark
R421-216-073-00 METAL CHIP10K5%1/10W
R431-216-042-00 METAL CHIP5105%1/10W
R441-216-021-00 METAL CHIP685%1/10W
R451-247-843-11 CARBON3.3K5%1/4W
R461-216-073-00 METAL CHIP10K5%1/10W
R471-216-097-91 METAL CHIP100K5%1/10W
R481-247-843-11 CARBON3.3K5%1/4W
R491-216-061-00 METAL CHIP3.3K5%1/4W
R501-216-065-00 METAL CHIP4.7K5%1/10W
R511-216-065-00 METAL CHIP4.7K5%1/10W
R531-249-429-11 CARBON10K5%1/4W
R541-249-399-11 CARBON335%1/4W
R551-216-162-00 METAL CHIP335%1/10W
R561-249-393-11 CARBON105%1/4W
R911-216-065-00 METAL CHIP4.7K5%1/10W
R921-216-073-00 METAL CHIP10K5%1/10W
R931-216-073-00 METAL CHIP10K5%1/10W
R941-216-073-00 METAL CHIP10K5%1/10W
R201-216-121-91 METAL CHIP1.0M5%1/10W
R211-216-049-91 METAL CHIP1.0K5%1/10W
R221-216-049-91 METAL CHIP1.0K5%1/10W
R231-216-049-91 METAL CHIP1.0K5%1/10W
R241-216-025-91 METAL CHIP1005%1/10W
R301-216-186-00 METAL CHIP3305%1/8W
R311-216-025-91 METAL CHIP1005%1/10W
R321-249-425-11 CARBON4.7K5%1/4W
R331-249-425-11 CARBON4.7K5%1/4W
R341-216-065-00 METAL CHIP4.7K5%1/10W
R351-216-214-00 METAL CHIP4.7K5%1/8W
R361-216-025-91 METAL CHIP1005%1/10W
R371-216-073-00 METAL CHIP10K5%1/10W
R381-216-089-91 METAL CHIP47K5%1/10W
R391-249-429-11 CARBON10K5%1/4W
HP101 1-500-093-11 HEAD,MAGNETIC (PLAYBACK) (DECK A)
HRPE1011-500-094-11 HEAD, MAGNETIC (REC/PB/ERASE) (DECK B)
M1X-3371-223-1 MOTOR ASSY (CAPSTAN)
M2A-2004-410-A MOTOR ASSY, DC (TRIGGER)
M101X-4917-523-4 MOTOR ASSY (SPINDLE)
M102X-4917-504-1 MOTOR ASSY (SLED)
M903A-4604-363-A MOTOR (L)ASSY (LOADING)
S1011-572-085-11 SWITCH, LEAF (LIMIT)