Sony CBEH19Z1, CBEH19C1 User Manual

EN
FR

Safety and Support
Sécurité et support technique

CECH-4001C

4-431-009-51(1)

WARNING

To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel
only.

Caution
Use of controls or adjustments or performance of
procedures other than those specified herein
may result in hazardous radiation exposure.

The use of optical instruments with this product
will increase eye hazard.

This appliance is classified as a CLASS 1 LASER product under
IEC60825-1:2007.

2

FCC and IC notice

This equipment complies with FCC/IC radiation exposure limits
set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines in Supplement C to
OET65 and RSS-102 of the IC radio frequency (RF) Exposure
rules. This equipment should be installed and operated with at
least 20 cm (8 in) and more between the radiator and person’s
body (excluding extremities: hands, wrists, feet and ankles).
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
The wireless controller complies with FCC/IC radiation exposure
limits set forth for uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines in Supplement C to
OET65 and RSS-102 of the IC radio frequency (RF) Exposure
rules. This equipment has very low levels of RF energy that are
deemed to comply without testing of specific absorption rate
(SAR).

NOTE:

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and

receiver.

– Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician

for help.

You are cautioned that any changes or modifications not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

If you have questions about this product, call our technical
support line at 1-800-345-7669 or write to:
Sony Computer Entertainment America LLC
Consumer Services/Technical Support
PO Box 5888, San Mateo, CA 94402-0888 U.S.A.

Trade Name : SONY
Model No. : CECH-4001C
Responsible Party : Sony Electronics Inc.
Address : 16530 Via Esprillo San Diego,

Telephone No. : 858-942-2230
This device complies with Part 15 of the FCC Rules and
RSS-Gen of IC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.

Declaration of Conformity

CA 92127 U.S.A.

Photosensitivity/Epilepsy/Seizures

A very small percentage of individuals may experience epileptic
seizures or blackouts when exposed to certain light patterns or
flashing lights. Exposure to certain patterns or backgrounds on
a television screen or when playing video games may trigger
epileptic seizures or blackouts in these individuals. These
conditions may trigger previously undetected epileptic
symptoms or seizures in persons who have no history of prior
seizures or epilepsy. If you, or anyone in your family, has an
epileptic condition or has had seizures of any kind, consult your
doctor before playing.

IMMEDIATELY DISCONTINUE use and consult your doctor
before resuming gameplay if you or your child experience any
of the following health problems or symptoms:

• dizziness,

• altered vision,

• eye or muscle twitches,

• loss of awareness,

• disorientation,

• seizures, or

• any involuntary movement or convulsion.

RESUME GAMEPLAY ONLY ON APPROVAL OF YOUR
DOCTOR.

Use and handling of video games to reduce the likelihood
of a seizure

• Use in a well-lit area and keep as far away as possible from
the television screen.

• Avoid large screen televisions. Use the smallest television
screen available.

EN

3

• Avoid prolonged use of the PS3™ system. Take a 15-minute
break during each hour of play.

• Avoid playing when you are tired or need sleep.

3D images

Some people may experience discomfort (such as eye strain,
eye fatigue, or nausea) while watching 3D video images or
playing stereoscopic 3D games on 3D televisions. If you
experience such discomfort you should immediately
discontinue use of your television until the discomfort subsides.
SCE recommends that all viewers take regular breaks while
watching 3D video, or playing stereoscopic 3D games. The
length and frequency of necessary breaks may vary from
person to person - please take breaks that are long enough to
allow any feelings of discomfort to subside. If symptoms persist,
consult your doctor.
The vision of young children (especially those under six years
old) is still under development. SCE recommends that you
consult with a doctor (such as a pediatrician or eye doctor)
before allowing a young child to watch 3D video images or play
stereoscopic 3D games. Adults should supervise young
children to ensure they follow the recommendations listed
above. When using any 3D enabled device with your
PlayStation®3 system you should read the instruction manual for
that device and check www.us.playstation.com/support/3D for
updated information.

Radio waves

Radio waves may affect electronic equipment or medical
devices (for example, pacemakers), which may cause
malfunctions and possible injuries.

4

• If you use a pacemaker or other medical device, consult your
doctor or the manufacturer of your medical device before
using the wireless networking feature (Bluetooth® and
wireless LAN).

• Do not use the wireless networking feature in the following
locations:

– Areas where wireless network use is prohibited, such as in

hospitals. Abide by medical institution regulations when
using the system on their premises.

– Areas near fire alarms, automatic doors and other types of

automated equipment.

About the lithium coin memory back-up battery

The lithium coin memory back-up battery inside this product
contains Perchlorate. The following statement is required by the
State of California, USA:
Perchlorate Material - special handling may apply. See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate

Contents

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Using the Wireless Controller . . . . . . . . . . . . . . . . . 10

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Before disposing of the system . . . . . . . . . . . . . . . . . 15

LIMITED HARDWARE WARRANTY AND LIABILITY . . . . 15

Copyright and trademarks . . . . . . . . . . . . . . . . . . . . 17

EN

5

Precautions

Before using this product, carefully read all the precautions.

Safety

This product has been designed with the highest concern for
safety. However, any electrical device, if used improperly, has
the potential for causing fire, electrical shock or personal injury.
To help ensure accident-free operation, follow these guidelines:

• Observe all warnings, precautions and instructions.

• Regularly inspect the AC power cord for damage.

• Stop use, unplug the AC power cord from the electrical outlet
and disconnect any other cables immediately if the device
functions in an abnormal manner, produces unusual sounds
or smells or becomes too hot to touch.

• Do not handle damaged or leaking Lithium-Ion batteries.

• If you come into contact with material from a leaking battery,
take the following actions:

– If the material gets into the eyes, do not rub. Immediately

flush the eyes with clean water and seek medical attention.

– If the material comes into contact with the skin or clothes,

immediately rinse the affected area with clean water.
Consult your doctor if inflammation or soreness develops.

• Do not allow the battery to come into contact with fire or
subject it to extreme temperatures such as in direct sunlight,
in a vehicle exposed to the sun or near a heat source.

• For more information on product safety and support, visit our
website ( back cover).

6

Use and handling

• Do not use the system in a closed cabinet or other locations
where heat may build up. Doing so may cause the system to
overheat and may lead to fire, injury or malfunction.

• If the system's internal temperature becomes elevated, the
power indicator will flash alternately in red and green. In this
case, turn off the system and leave it unused for a while. After
the system cools down, move it to a location with good
ventilation, and then resume use.

• Use in a well-lit area and keep as far away as possible from
the television screen.

• Avoid prolonged use of the PS3™ system and wireless
controller.

• Stop using the system immediately if you begin to feel tired or
if you experience discomfort or pain in your hands or arms
while operating the wireless controller. If the condition
persists, consult a doctor.

• If you experience any of the following health problems,
discontinue use of the system immediately. If symptoms
persist, consult with your doctor.

– Dizziness, nausea, fatigue or symptoms similar to motion

sickness

– Discomfort or pain in a part of the body, such as eyes, ears,

hands or arms

• Keep the system and accessories, including cable ties and
fasteners, out of the reach of small children.

• Do not connect cables other than a USB cable while the
system is turned on (power indicator is lit solid green).

• Any TV or component connected to the system must be
functioning properly and free of defects. If a TV or component
connected to the system is faulty or defective, it may cause
damage to the TV or component, or to the system itself. As
with all electrical products, connection to faulty or defective

components, or the failure to connect to a properly wired
outlet, may cause sparking and pose a fire hazard.

• Do not touch the system or connected cables or accessories
during an electrical storm.

• Do not use the system or accessories near water.

• Do not allow liquid, small particles or other foreign objects to
get into the system or accessories.

• Do not touch the connectors of the system or accessories.

• Do not expose the system or accessories to dust, smoke or
steam. Also, do not place the system in an area subject to
excessive dust or cigarette smoke. Dust build-up or cigarette
smoke residue on the internal components (such as the lens)
may cause the system to malfunction.

• Do not expose the system or accessories to high
temperatures, high humidity or direct sunlight.

• Do not place the system or accessories on surfaces that are
unstable, tilted or subject to vibration.

• Do not set the system other than in the vertical or horizontal
position. When setting the system in the vertical position, use
the vertical stand (sold separately) for this model of the
system. Also, do not change the position of the system while
it is turned on.

• Be careful when carrying the system. If you do not have a
good grip, the system may drop causing potential damage or
injury.

• Keep the disc cover closed except when inserting or
removing discs. Leaving the disc cover open may result in
damage to internal components (such as the lens) or system
malfunction.

• Be careful not to pinch your hands or fingers when closing the
disc cover. This can cause injuries or system malfunction.

• Do not touch a disc while it is spinning. This can cause
injuries, damage to the disc, or system malfunction.

• Do not turn off the system while data is being saved on or
loaded from the hard disk.

• Do not move or change the position of the system while the
power indicator is lit solid green or flashing green. The
vibration that occurs as a result of moving the system may
cause data loss or corruption, or damage to the system.

• Do not stand on or put objects on the system, and do not
stack the system with other devices.

• Do not place the system and connected accessories on the
floor or in a place where they may cause someone to trip or
stumble.

• Do not allow bodily contact with the system or air from the
system vents for an extended period of time while in use.
Extended contact under these conditions may cause low­temperature burns.

• When connecting the system to a plasma or projection* TV,
do not leave a still image on the TV screen for an extended
period of time, as this may leave a faint image permanently on
the screen.

* Except LCD screen types

• Parents are encouraged to monitor children in online activities
to ensure safe and responsible Internet usage.

About the USB device

If "An unknown USB device has been connected" is displayed
on-screen, the reason may be one of the following:

• The connected USB device is not compatible with the system.

• The connected USB device is compatible with only some
software titles.

• Too many USB devices are connected to the USB hub.

EN

7

Notes on safety when using the DUALSHOCK®3
Wireless Controller*

• Stop using the system immediately if you begin to feel tired or
if you experience discomfort or pain in your hands or arms
while operating the DUALSHOCK®3 Wireless Controller. If the
condition persists, consult a doctor.

• The vibration function of the DUALSHOCK®3 Wireless
Controller can aggravate injuries. Do not use the vibration
function if you have any ailment or injury to the bones, joints
or muscles of your hands or arms. If you have an ailment or an
injury, do not play software titles that contain the vibration
function using the DUALSHOCK®3 Wireless Controller unless
you have set the vibration function to [Off].

• Avoid prolonged use of the DUALSHOCK®3 Wireless
Controller. Take a break at about 30-minute intervals.

• Note that some software titles set the vibration function to [On]
by default. To disable the vibration function, press the PS
button of the controller, and then select [Controller Settings]

[Vibration Function] [Off].

• When using the motion sensor function of the wireless
controller, be cautious of the following points. If the controller
hits a person or object, this may cause accidental injury or
damage.

– Before using, check that there is plenty of space around

you.

– When using the controller, grip it firmly to make sure it

cannot slip out of your hand.

– If using a controller that is connected to the PS3™ system

with a USB cable, make sure there is enough space for the
cable so that the cable will not hit a person or object. Also,
take care to avoid pulling the cable out of the PS3™ system
while using the controller.

8

– Some PlayStation® and PlayStation®2 peripherals such as

the analog controller (DUALSHOCK®) and analog
controller (DUALSHOCK®2) are not compatible with the
PS3™ system. For details, visit www.us.playstation.com.

* These notes may also apply to other controllers.

Vents

Do not block any vents. To maintain good ventilation, follow the
guidelines below:

• Place the system at least 10 cm (4 in) away f rom a wall surface.

• Do not place on a carpet or rug with long fibers.

• Do not place in a narrow or cramped space.

• Do not cover with cloth.

• Do not allow dust to build up on the vents.

AC power cord use

• Any TV or component connected to the system must be
functioning properly and free of defects. If a TV or component
is faulty or defective, it may cause damage to the TV or
component, or to the system itself. As with all electrical
products, connection to faulty or defective components, or
the failure to connect to a properly wired outlet, may cause
sparking and pose a fire hazard.

• Do not plug the AC power cord for the system into an
electrical outlet until you have made all other connections.
Make sure the TV or other component is unplugged from the
electrical outlet prior to connecting it to the system.

• To help ensure safe oper ation, regularly inspect the AC pow er
cord. If damaged, stop use immediately and contact SCEA
Consumer Services ( back cover).

• Do not use a power cord other than the supplied AC power
cord. Do not modify the cord.

• Do not touch the plug of the AC power cord with wet hands.

• Protect the AC power cord from being walked on or pinched
particularly at plugs, expansion receptacles and the point
where the cord exits from the system.

• Do not place heavy items on the cord.

• Do not place the AC power cord near heating equipment and
do not expose the cord to heat.

• Unplug the AC power cord from the electrical outlet before
cleaning or moving the system, or when you do not intend to
use the system for an extended period of time. When
disconnecting, grasp the power cord by the plug and pull
straight out of the electrical outlet. Never pull by the cord and
do not pull out at an angle.

• Do not connect the AC power cord to a voltage transformer or
inverter. Connecting the AC power cord to a voltage
transformer for overseas travel or an inverter for use in an
automobile may cause heat to build up in the system and may
cause burns or a malfunction.

Never disassemble or modify the system or
accessories

Use the PS3™ system and accessories according to the
instructions in the product documentation. No authorization for
the analysis or modification of the system or accessories, or the
analysis and use of its circuit configurations, is provided.
Unauthorized modification of the system or accessories will void
your warranty. There are no user serviceable components
inside the PS3™ system (the supplied hard disk may be
removed but not disassembled or modified).
Additionally, there is a risk of exposure to laser radiation as well
as to electrical shock.

Network

• A broadband connection is required to access the Internet.
Note that dial-up connectivity is not supported.

• User is responsible for Internet service fees. For details, refer
to the information provided in your service contract or contact
your Internet service provider.

• Do not use a cord for a standard residential telephone line or
cables of types other than those mentioned here. Using the
wrong type of cord or cable can cause more electrical current
than necessary to flow through the LAN connector, which may
lead to heat build-up, fire or malfunction.

Wireless networking feature

• The 2.4 GHz range of radio waves used by the wireless
networking feature of this product is a range shared by
various devices. This product has been designed to minimize
the effect of other devices using the same range. However, in
some cases interference from other devices may reduce the
connection speed, shorten the signal range or cause the
connection to be terminated unexpectedly.

• When using the PS3™ system’s scan function to select a
wireless LAN access point, access points that are not
intended for public use may be displayed. Only connect to an
access point that you are authorized to use.

Moisture condensation

If the system or disc is brought directly from a cold location to a
warm one, moisture may condense on the lens inside the
system or on the disc. Should this occur, the system may not
operate properly. In this case, remove the disc and turn off and

EN

9

unplug the system. Do not put the disc back in until the moisture
evaporates (this may take several hours). If the system still does
not operate properly, contact SCEA Consumer Services
( back cover).

Protecting the lens and and the surrounding area

Do not touch the lens located inside the disc cover or any of the
parts around the lens. To help protect the lens from dust, keep
the disc cover closed except when inserting or removing discs.
If the lens is dirty, or if you touch the parts around the lens, the
system may not operate properly.

10

Using the Wireless Controller

If you disconnect the USB cable, you can use the controller
wirelessly. To use it wirelessly, the controllerfs battery must be
charged. You can check the battery level on the screen by
pressing the PS button for at least one second.

Pairing the controller with a PS3™ system

When using the controller for the first time, you must first pair the
PS3™ system and the controller. To pair the devices, connect
the controller and the system using a USB cable and press the
PS button.
When using two or more controllers, each controller must be
paired with the PS3™ system separately.

Hint

You can connect up to seven controllers at one time.

Charging the battery

To charge the controller battery, connect the controller to the
system using a USB cable while the system is turned on.

Hint

Charge in an environ ment where the temperature range is between
10° C - 30° C (50°F - 86°F). Charging may not be as effective when
performed in other en vironments.

Wireless controller battery life

The battery has a limited lifespan. Battery duration will gradually
decrease with repeated usage and age.

Hint

Battery life also varies depending on the storage method, usage
state, environment and other factors.

Storage

When the wireless controller is not used for an extended period
of time, it is recommended that you fully charge it at least once
a year in order to maintain battery functionality.

Specifications

Design and specifications are subject to change without notice.
Information about system functionality and images published in
this document may vary from those for your PS3™ system,
depending on the system software version in use.

PlayStation®3 system

CPU Cell Broadband Engine™

GPU RSX™

Audio output

Memory

*3

2.5" Serial
ATA

Hi-Speed USB
(USB 2.0)

Hard disk

Inputs/
outputs

Networking

Controller Wireless Controller (Bluetooth

LPCM 7.1ch, Dolby Digital,
Dolby Digital Plus, Dolby
TrueHD, DTS, DTS-HD, AAC

256 MB Main Memory,
256 MB Graphics Memory

*1*2

500 GB

2

Ethernet (10BASE-T, 100BAS E-TX,
1000BASE-T) × 1

IEEE 802.11 b/g

® 2.0 (EDR)

Bluetooth

®)

EN

11

Resolution 1080p, 1080i, 720p, 480p, 480i

HDMI™ OUT
connector

AV output

BD/DVD/CD
drive
(read only)

Laser

Power 120 V AC, 60 Hz

Power consumption Approx. 190 W

External dimensions
(excluding maxim um
projecting part)

Mass Approx. 2.1 kg (4.6 lb)

Operating temperature 5° C - 35° C (41°F - 95°F)

AV MULTI OUT
connector

Digital out
(optical)
connector

Maximum
read rate

1

*4

1

1

BD × 2 (BD-ROM)
DVD × 8 (DVD-ROM)
CD × 24 (CD-ROM)

Type: Semiconductor,

continuous

BD Wavelength: 400 - 410 nm

Power: Max. 17.5 mW

DVD Wavelength: 655 - 664 nm

Power: Max. 2.6 mW

CD Wavelength: 770 - 800 nm

Power: Max. 4.0 mW

Approx. 290 × 60 × 230 mm
(11.4 × 2.4 × 9.1 in)
(width × height × length)

12

*1 Hard disk capacity calculated using base 10 mathematics (1GB =

1,000,000,000 bytes). The system software for this PS3™ system
calculates capa city using binary mathematics (1GB =
1,073,741,824 bytes) and consequently displays lower capacity
and free space. The difference in displayed values does not
indicate a difference in the actual number of bytes.

*2 A portion of the hard disk capacity is reserved for use in

connection with system administration, maintenance, and
additional options. This may occur upon installation of system
software or other software. As a result, the availa bility of hard disk
capacity may vary depending on the system, system software
version, or available options, and is not otherwise available for

your use.
*3 Functionality of all connected devices is not guaranteed.
*4 "3D", "Deep Color", "x.v.Color" and "HD lossless audio format" are

supported.

Playable discs

For additional information on compatible media types, visit our
website at www.us.playstation.com.

®3 format BD-ROM

PlayStation

Blu-ray Disc™ (BD)

BD-ROM

BD-R

BD-RE

*1