Sony 76c User Manual

Page 1
Epson® PowerLite® 76c
Multimedia Projector
User’s Guide
Page 2

Important Safety Information

WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.
Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

Trademarks

Epson is a registered trademark, and Exceed Your Vision and Instant Off are trademarks of Seiko Epson Corporation.
PowerLite, PrivateLine, and Presenters Club are registered trademarks; SizeWise is a trademark; and Epson Connection, Epson Store, and Extra Care are service marks of Epson America, Inc.
Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
© 2005 Epson America, Inc. 8/05
2
Page 3

Contents

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Getting the Most from Your Projector . . . . . . . . . . . . . . . . . 8
Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 9
Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 9
Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10
Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Projector Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Additional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1 Setting Up the Projector . . . . . . . . . . . . . . . . . . . . 15
Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Other Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . 18
Connecting with the VGA Cable . . . . . . . . . . . . . . . . . 19
Connecting with a VGA-5BNC Cable. . . . . . . . . . . . . 20
Connecting a USB Cable for Remote Mouse Control . 21
Connecting an External Monitor . . . . . . . . . . . . . . . . . 22
Playing Sound Through the Projector . . . . . . . . . . . . . 23
Connecting to Video Sources . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting a Composite Video Source . . . . . . . . . . . . 25
Connecting an S-Video Source . . . . . . . . . . . . . . . . . . 26
Connecting an RGB Video Source. . . . . . . . . . . . . . . . 27
Connecting a Component Video Source . . . . . . . . . . . 28
Playing Sound Through the Projector . . . . . . . . . . . . . 29
3
Page 4
2 Projecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Turning On Your Equipment . . . . . . . . . . . . . . . . . . . . . . . 32
Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 32
Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 34
What To Do If You See a Blank Screen . . . . . . . . . . . . . 34
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Focusing and Zooming Your Image. . . . . . . . . . . . . . . . 37
Adjusting the Height of Your Image . . . . . . . . . . . . . . . 38
Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 39
Adjusting the Brightness . . . . . . . . . . . . . . . . . . . . . . . . 39
Correcting Computer Images. . . . . . . . . . . . . . . . . . . . . 40
Adjusting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 40
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 41
3 Using the Remote Control . . . . . . . . . . . . . . . . . . . 43
Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 44
Switching Between Picture Sources . . . . . . . . . . . . . . . . 44
Turning Off the Picture and Sound. . . . . . . . . . . . . . . . 45
Stopping Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Zooming Your Image. . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Changing the Image’s Aspect Ratio . . . . . . . . . . . . . . . . 46
Using the Remote Control as a Wireless Mouse . . . . . . . . . . 47
Replacing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4 Fine-tuning the Projector. . . . . . . . . . . . . . . . . . . . 49
Using the Projector’s Menu System . . . . . . . . . . . . . . . . . . . 50
Changing Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . 51
Adjusting Colors and Clarity . . . . . . . . . . . . . . . . . . . . . . . . 53
Adjusting the Input Signal . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 58
Selecting Projector Setup Options . . . . . . . . . . . . . . . . . . . . 60
4
Page 5
Viewing Lamp Usage and Other Information . . . . . . . . . . . 62
Using the Projector’s Security Features. . . . . . . . . . . . . . . . . 63
Creating Your Own Screen Logo. . . . . . . . . . . . . . . . . . 64
Setting a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Turning On the Password and User’s Logo . . . . . . . . . . 66
Starting the Projector with a Password. . . . . . . . . . . . . . 67
Disabling the Projector’s Buttons . . . . . . . . . . . . . . . . . 68
Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . . . . 69
5 Maintaining and Transporting the
Projector
Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 72
Cleaning and Replacing the Air Filter . . . . . . . . . . . . . . . . . 73
Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Transporting the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . 78
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
6 Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Using On-Screen Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
What To Do When the Lights Flash . . . . . . . . . . . . . . . . . . 81
Solving Problems with the Image or Sound . . . . . . . . . . . . . 83
Solving Password Problems . . . . . . . . . . . . . . . . . . . . . . . . . 90
Solving Problems with the Remote Control . . . . . . . . . . . . . 90
Where To Get Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Telephone Support Services. . . . . . . . . . . . . . . . . . . . . . 92
5
Page 6
A Technical Specifications . . . . . . . . . . . . . . . . . . . . . 95
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Projection Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Mouse Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Safety and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Compatible Video Formats . . . . . . . . . . . . . . . . . . . . . . . . . 98
Compatible Computer Display Formats. . . . . . . . . . . . . . . . 99
B Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . 101
Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . 103
FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 104
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
6
Page 7
-

Welcome

The Epson
®
PowerLite® 76c is an ultra-portable projector that offers 2000 ANSI lumens of brightness. From conference rooms to auditoriums, your full-color presentations and videos will be bright and visible even in ordinary indoor lighting.
Images are displayed at a native resolution of 1024 × 768 pixels. Epson 3LCD technology ensures accurate color and remarkable saturation, even in well-lit rooms. Support for S-Video contributes to theater-quality performance.
You can connect the projector to a wide range of computers, including
®
IBM
-compatible PCs and laptops, Apple® Macintosh,® Power Macintosh computers, and many iMac patented SizeWise
®
series (including G3, G4, and G5 systems), PowerBook®
®
and iBook® series systems. With Epson’s
technology, the projector supports computer
displays ranging from VGA through UXGA.
You can use any of the following video sources: HDTV, VCR, DVD player, gaming console (such as Microsoft PlayStation
®
2, and Nintendo GameCube™), camcorder, digital
®
Xbox,™ Sony®
camera, or laser disc player. The projector supports NTSC, PAL, and SECAM video formats.
You can connect up to three devices to the projector at the same time. The source buttons let you easily switch among them. With the projector’s
Source Search button, you don’t even have to identify
your input source. Just press the button until you see the image you want on the screen.
To prevent unauthorized use of the projector, you can assign a password, create a user logo which is displayed at startup to identify the projector, and disable the projector’s buttons through the Operation Lock feature. For more information about security features, see page 63.
7
Page 8

Getting the Most from Your Projector

Depending on your presentation, you can take advantage of any or all of these options:
Connecting to a laptop or other computer
If you want to connect the projector to a laptop or desktop computer, see page 18. For additional presentation control, you can connect a USB cable to the projector for running slide shows, and connect an external monitor to view the presentation on your computer simultaneously.
Connecting to video sources
You can connect a DVD player, VCR, HDTV, camcorder, laser disc player, digital camera, and other video sources to your projector. See page 24 for instructions.
Using the remote control
The remote control lets you switch from computer to video sources, zoom in on part of your image, freeze or mute the presentation, and adjust many other projector features. For details, see Chapter 3.
By connecting a USB cable to your projector, you can also use the remote control as a wireless mouse. This lets you click through computer-based presentations (such as PowerPoint 20 feet away. For more information, see page 47.
®
) from up to
8 Welcome
Page 9

Using Your Documentation

Your documentation includes a Quick Setup sheet, warranty brochures, and an Epson PrivateLine
The Quick Setup sheet gives instructions to quickly set up your projector and connect it to a computer or video device.
This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it:
Warnings must be followed carefully to avoid bodily injury.
Cautions must be observed to avoid damage to your equipment.
Notes contain important information about your projector.

Getting More Information

Need tips on giving presentations? How about quick steps for setting up your projector? Here’s where you can look for help:
www.presentersonline.com
Includes a library of articles covering presentation tips, tricks, and technology. The site provides templates, clip art, and sound clips, as well as Presenters Services to use on the road. Even more resources and services are available if you register to join the Presenters Club
®
—and it’s free.
®
Support card.
Built-in help system
Press the Help button on the remote control or projector to get quick solutions for common problems. See page 80 for details.
support.epson.com
Download FAQs (frequently asked questions) and e-mail your questions to Epson support.
If you still need help after checking this User’s Guide and the sources listed above, you can use the Epson PrivateLine Support service to get help fast. Call (800) 637-7661 and enter the PIN on your PrivateLine Support card. See page 92 for more information.
Welcome 9
Page 10

Registration and Warranty

Your projector comes with a basic carry-in warranty and an international warranty that let you project with confidence anywhere in the world. For details, see the warranty brochures that came with your projector.
In addition, Epson offers free Extra Care
SM
Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada, usually via overnight delivery. See the Extra Care Road Service brochure for details.
To register, complete the registration form that came with your projector and mail it to Epson. Or register your product online at:
http://www.epson.com/webreg
Registering also lets you receive special updates on new accessories, products, and services.

Unpacking the Projector

After unpacking the projector, make sure you have all these items:
Quick Setup sheet
10 Welcome
Projector
VGA computer cable
Remote control
and batteries
Power cord
Soft carrying case
Password Protected Sticker
Page 11
Save all packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when you need to send the projector to another location.
If you are moving the projector by hand, use the carrying case included with the projector.

Projector Parts

Temperature light
Lamp light
Control panel
Lamp cover
Air exhaust vents Front adjustable foot Foot release lever
Computer(Component Video) port
Monitor Out port
Power inlet
S-Video port
Power button
Video port
USB port for wireless mouse
Security lock
Power light
Zoom ring
Focus ring
Remote control sensor
Lens cap
Remote control sensorSpeakerAudio input portsRear adjustable foot
Welcome 11
Page 12

Additional Components

Depending on how you plan to use the projector, you may need additional components:
To receive an S-Video signal, you need an S-Video cable. One is
usually provided with your video device, or you can purchase it from Epson. See page 13.
To receive a component video signal from a VCR or other video
device, you need a D-sub, 15-pin, VGA-to-component video cable, which is available from Epson. See page 13.
Some older PowerBooks and Macintosh desktop models may
need a Macintosh video adapter; see your computer dealer. Older iMac systems may need a special adapter to provide a VGA output port; see your computer dealer.
To receive an audio signal, you need a commercially available
audio cable; see your computer or electronics dealer.
To use the projector’s remote control as a wireless mouse, you
need a USB cable; see your computer or electronics dealer.
12 Welcome
Page 13

Optional Accessories

To enhance your use of the projector, Epson provides the following optional accessories:
Product Product number
Replacement lamp V13H010L34
Air filter set (includes 2 filters) V13H134A08
®
Samsonite laptop
Samsonite soft shoulder case with laptop compartment
Component video cable S-Video cable
Distribution amplifier ELPDA01
50-inch portable screen 60-inch portable pop-up screen 80-inch portable pop-up screen
83.6-inch hanging pull-down screen
Image presentation camera ELPDC05 V12H162020
Kensington
Ceiling mount (gyro lock with suspension adapter) False ceiling plate Suspension adapter Security bracket/cabling for gyro lock mounts Adjustable ceiling channel
wheeled soft case for projector and
®
security lock ELPSL01
ELPKS35-S
ELPKS43
ELPKC19 ELPSV01
ELPSC06 ELPSC07 ELPSC08 ELPSC09
ELPMBUNI ELPMBFCP ELPMBAPL ELPMBSEC ELPMBACC
note
To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer referral in Canada).
You can purchase video cables, screens, carrying cases, or other accessories from an Epson authorized reseller. Please call 800-GO-EPSON (800-463-7766) for product information and to find the nearest authorized reseller. To purchase online, visit the Epson Store
SM
at www.epsonstore.com (U.S. sales only). In Canada,
please call (800) 463-7766 for dealer referral.
Welcome 13
Page 14
14 Welcome
Page 15

Setting Up the Projector

This chapter tells you how to set up the projector and connect it to a
computer or video source. You can connect up to three devices simultaneously: three video sources or one computer and two video sources.
You’ll find instructions for the following in this chapter:
Positioning the projector
Connecting to a computer
Connecting to video sources
1
15
Page 16

Positioning the Projector

Before connecting the projector, you need to decide where to place it. If you’re setting up the projector yourself and it isn’t already installed in the room you’re using, you’ll probably want to place it on a table in front of the screen, as shown.
This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it. Try to leave as much space as possible between the projector and the screen to get a good-size image.
Place the projector somewhere between 3 and 35 feet from the screen. Use the figure below to help you determine exactly how far. Image size increases with distance, but can vary depending on how you’ve adjusted the optical zoom and other settings.
note
You can download the Projection Distance Calculator program from the Drivers and Downloads section of Epson’s web site:
http://support.epson.com.
16 Setting Up the Projector
29.5 to 35.4 feet
5.8 to 7 feet
2.8 to 3.4 feet
Also keep these considerations in mind:
Place the projector on a sturdy, level surface.
Make sure there is plenty of space for ventilation around and
under the projector. Do not set the projector on top of loose papers that could block the vents under the projector.
Make sure the projector is within 6 feet (2 m) of a grounded
electrical outlet or extension cord.
Page 17
Try to place the projector directly in front of the center of the screen, facing it toward the screen squarely. If the projector isn’t positioned this way, the image will be “keystone” shaped, instead of square or rectangular.
If you place the projector below the level of the screen, you’ll have to tilt it up by extending the front adjustable foot, as described on page 38. This also causes the image to be keystone shaped, instead of square or rectangular. To adjust the keystone correction value, see page 39.

Other Installations

You can also project from behind the screen or from the ceiling, with the projector mounted upside-down:
translucent screen)
Rear/ceiling projection (using a translucent screen)
To project from overhead, you’ll need the optional ceiling mount hardware. (See page 13 for ordering information.) You’ll also need to select
Front/Ceiling or Rear/Ceiling for the Projection option in the
Extended menu. To project from the rear, select
Rear. See page 60 for
more information.
Front/ceiling projectionRear projection (using a
Setting Up the Projector 17
Page 18

Connecting to a Computer

note
If you have an iBook with an RCA video-out port, follow the instructions for connecting to a video device on page 25.
You can connect the PowerLite projector to any computer that has a standard VGA or BNC monitor port, including PC notebook and laptop computers, Macintosh PowerBooks and iBooks, and hand-held devices.
Follow the instructions in this section to:
Connect the projector to your computer with the VGA cable
included with the projector.
Connect the projector to your computer with a commercially
available VGA–5BNC cable.
After connecting the projector to your computer, you may also want to:
Connect a USB cable to your projector so that you can use the
remote control as a wireless mouse; see page 21
Connect a monitor to the projector so you can view your
presentation close-up as well as on-screen (not necessary if you’re using a laptop); see page 22
Connect the projector to your computer with a commercially
available audio cable to play computer audio; see page 23
18 Setting Up the Projector
Page 19

Connecting with the VGA Cable

Follow these instructions to connect to your computer with the VGA cable that came with your projector. Before you start, make sure your computer and the projector are turned off.
1. If you are connecting the projector to a desktop computer, disconnect the monitor cable from your computer.
2. Locate the VGA computer cable that came with the projector.
Connect one end of the cable to the projector’s
Video)
3. Connect the other end of the cable to your computer’s video-out or monitor port.
If you’re using a PowerBook or iBook and you can’t connect the cable, you may need to use an optional Macintosh video adapter; see your computer dealer.
Computer(Component
port.
VGA computer cable
4. If you want to view the display simultaneously on your computer monitor and the projector screen, see “Connecting an External Monitor” on page 22.
5. Tighten the screws on the connectors.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
If more than one device is connected to the projector, select the correct source after projection starts by pressing the button on the projector or the
Comp button on the remote control.
Source Search
See page 34.
Setting Up the Projector 19
Page 20
VGA-5BNC cable

Connecting with a VGA-5BNC Cable

If your computer provides video output through BNC connectors, follow these instructions to connect the projector to your computer with an optional VGA-5BNC cable. Before you start, make sure your computer and the projector are turned off.
1. Disconnect the monitor cable from your computer.
2. Connect the cable’s VGA connector to the projector’s
Computer(Component Video) port.
3. Connect the BNC connectors to your computer’s BNC ports.
4. If you want to view the display simultaneously on your computer monitor and the projector screen, see “Connecting an External Monitor” on page 22.
5. Tighten the screws on the VGA connector.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
20 Setting Up the Projector
If more than one device is connected to the projector, select the correct source after projection starts by pressing the button on the projector or the
Comp button on the remote control.
Source Search
See page 34.
Page 21

Connecting a USB Cable for Remote Mouse Control

Using the remote control as a wireless mouse lets you click through slide show-style presentations, such as PowerPoint, from up to 20 feet away. This makes it easy to deliver your presentation, since you won’t need to stand near your computer.
To use the wireless mouse function, you will need a USB cable, a system with a working USB port, and the full version of one of these operating systems:
note
For details about using the remote control as a wireless mouse, see page 47.
Windows
Windows 98SE, 2000, Me, or XP Macintosh OS 9, OS X
®
Macintosh
1. If you are using a desktop computer, disconnect the mouse cable from your computer.
2. Connect the square end of the USB cable to the projector’s USB port.
3. Connect the flat end of the cable to any available USB port on your computer.
4. If necessary, configure your laptop to work with an external mouse.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
Setting Up the Projector 21
Page 22
note
Some LCD monitors may not be able to display the image correctly. If you have trouble displaying the image, connect a multiscan monitor. If you’re projecting computer images, make sure the computer’s refresh rate is set to 65 Hz or greater.

Connecting an External Monitor

If you want to see your presentation close-up as well as on the projection screen, you can connect an external monitor to the projector. This lets you view images on your computer monitor while the projector is in standby mode (plugged in but not turned on) and check your presentation or switch between picture sources even if you’ve pressed the projection on the screen.
Simultaneous display is possible only when the computer is connected to the projector’s
Make sure the projector and computer are off. Then connect the monitor’s cable to the projector’s
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
A/V Mute button on the remote control to turn off
Computer(Component Video) port.
Monitor Out port, as shown:
22 Setting Up the Projector
Page 23

Playing Sound Through the Projector

You can connect a commercially available audio adapter cable to take advantage of the projector’s built-in speaker. You can obtain an audio adapter cable (3.5-mm stereo miniplug to two male RCA plugs) from a computer or electronics dealer.
1. Connect the RCA plugs on the audio adapter cable to the
L-Audio-R jacks on the projector.
2. Connect the other end of the audio cable to your laptop’s
headphone jack or audio-out jack, or your desktop’s
speaker or audio-out port.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
Setting Up the Projector 23
Page 24
note
The projector does not support TV antenna cable F connectors.

Connecting to Video Sources

You can connect a DVD player, VCR, camcorder, laser disc player, digital camera, gaming console—such as Microsoft Xbox, Sony PlayStation 2, or Nintendo GameCube—or any other compatible video source to your projector. You can connect up to three video devices at one time.
The projector supports HDTV, SDTV, NTSC, PAL, and SECAM, and automatically detects the video format. It can receive composite video, S-Video, RGB video, and component video. The type of cable you need depends on the video source:
For composite video, use a commercially available RCA A/V
cable. See page 25.
For S-Video, use the S-Video cable supplied with your video
device or order one from Epson. See page 26.
For RGB video, use the VGA computer cable included with the
projector. See page 27.
For component video, you’ll need the optional Epson component
video cable. See page 28.
24 Setting Up the Projector
After connecting your video device to the projector, you may want to connect an audio cable to play sound from your video equipment through the projector’s built-in speaker. See page 29 for instructions.
Page 25

Connecting a Composite Video Source

If you’re connecting a composite video device, use a commercially available RCA A/V cable. Before starting, make sure the projector and your DVD player or other video source are turned off.
1. Connect the yellow RCA plug on one end of the cable to the projector’s yellow
2. Connect the yellow plug on the other end of the cable to the video-out port on your video source.
3. To play sound through the projector, follow the instructions beginning on page 29.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
If more than one device is connected to the projector, select the correct source after projection starts by pressing the button on the projector or the Video button on the remote control. See page 34.
Video jack.
Source Search
Setting Up the Projector 25
Page 26

Connecting an S-Video Source

If your video source has an S-Video jack, you can use it to project a higher quality video image. You’ll need an S-Video cable, which is usually provided with your video source, or you can purchase one from Epson (part number ELPSV01). See page 13 for ordering information.
Before starting, make sure the projector and your DVD player or other video source are turned off.
1. Insert one end of the S-Video cable into the projector’s
S-Video
port and the other end into the S-Video output port of your video source.
2. To play sound through the projector, follow the instructions beginning on page 29.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
If more than one device is connected to the projector, select the correct source after projection starts by pressing the button on the projector or the
S-Video button on the remote control.
Source Search
See page 34.
26 Setting Up the Projector
Page 27

Connecting an RGB Video Source

Follow these instructions to connect the projector to a video player or satellite receiver that has an RGB video output port using the VGA computer cable that came with the projector.
Before starting, make sure the projector and your DVD player or other video source are turned off.
1. Connect one end of the VGA computer cable to the
Computer(Component Video) port on the projector.
2. Connect the other end to the video port on your player.
3. To play sound through the projector, follow the instructions beginning on page 29.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
If more than one device is connected to the projector, select
Computer (RGB) as the source after projection starts by pressing the Source Search button on the projector or the Comp button on the
remote control. See page 34.
Setting Up the Projector 27
Page 28

Connecting a Component Video Source

If your video source has component video connectors, you can use them to project a higher quality video image. You’ll need a component video cable, which can be purchased from Epson (part number ELPKC19). See page 13 for ordering information.
Before starting, make sure the projector and your DVD player or other video device are turned off.
1. Connect the large end of the component video cable to the projector’s
2. Insert the three ends of the component video cable into the
R, G, and B ports on your video source.
3. To play sound through the projector, follow the instructions beginning on page 29.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
Computer(Component Video) port.
28 Setting Up the Projector
If more than one device is connected to your projector, select
Computer (Component Video) as the source by pressing the Source
Search button on the projector or the
Comp button on the remote
control. See page 34.
Page 29

Playing Sound Through the Projector

The projector has a built-in speaker with a maximum output of 1 W. You can play sound from your video equipment through the projector’s speaker if your video device has an audio output port.
For RCA-Style Audio Output Ports
Most video devices have an RCA-style audio output port. In this case, use a commercially available RCA-style audio cable to connect the projector to your video source:
1. Connect the red and white plugs on one end of the audio cable to
L-Audio-R jacks on the projector.
the
2. Connect the red and white plugs on the other end of the audio cable to the corresponding color-coded audio output port on your video source.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
Setting Up the Projector 29
Page 30
For Stereo Mini-Jack Audio Output Ports
Some video devices, especially camcorders, may have a stereo mini-jack audio output port. In this case, use a commercially available audio adapter cable (3.5-mm stereo miniplug to two male RCA plugs) to connect to the projector:
1. Connect the red and white plugs on the audio adapter cable to the
L-Audio-R jacks on the projector.
2. Connect the other end of the audio adapter cable to your video device’s audio output port.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 32 for instructions.
30 Setting Up the Projector
Page 31

Projecting

Once you’ve set up the projector, you’re ready to turn it on, adjust
the image, and give your presentation.
Although you can operate the projector without it, the remote control lets you use additional features. See Chapter 3 for instructions on using the remote. This chapter covers the following:
Turning on the projector and other equipment
Adjusting the image
Adjusting the volume
Shutting down the projector
2
31
Page 32
caution
Do not use the projector with the lens cap in place. The heat generated by the lamp can damage it.

Turning On Your Equipment

Make sure your projector and other equipment are set up and connected correctly, as described in Chapter 1. Then turn on your projector, as described below.
If you turn on your connected computer or video equipment before starting the projector, the projector automatically detects and displays the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image source manually. See page 34.

Turning On the Projector

Follow these steps to plug in and turn on the projector:
1. Push in the tabs and remove the lens cap.
32 Projecting
2. Connect one end of the power cord to the projector’s power inlet.
3. Connect the other end to an electrical outlet.
The power light on top of the projector turns orange, indicating that the projector is receiving power but not yet turned on. Wait until the light stops flashing but stays orange.
Page 33
4. Turn on your computer or video source if you have not already.
5. Press the P (You can also press the P
Power button on top of the projector to turn it on.
Power button on the remote control.)
Power button
Projector Remote control
The projector beeps and the power light flashes green as the projector warms up. The projector lamp comes on in about 4 seconds and the power light stays green.
If you’re using a computer, you should see your computer
display projected after a moment or two. If not, you need to select the image source. See page 34.
note
If you are using the remote control for the first time, be sure to insert the batteries as described on the Quick Setup poster.
warning
Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.
(Windows only: If you see a message saying that it has found a plug-and-play monitor, click
If you’re projecting a video, press the Source Search button
Cancel.)
on the projector or remote control to switch to your video source. Then press the
Play button on your DVD player or
other device.
If you are prompted to enter a password, see page 67.
To focus and adjust the image, see page 37. If a projected image fails to appear, see “What To Do If You See a Blank Screen” on page 34.
When you’re done with your presentation, shut down the projector as described on page 41.
Projecting 33
Page 34
note
The name of the selected image source appears in the upper right corner of the screen.

Selecting the Image Source

Selecting the image source lets you switch between images input from different pieces of equipment connected to the projector (such as a computer and DVD player). If you don’t see the image you want, press one of the following buttons on the remote control:
Comp
Press this button to move through the following options:
Computer (Auto), Computer (RGB), and Computer (Component Video)
S-Video
Press to select S-Video.
Video
Press to select Video.
.
You can also press the
Source Search button on the remote control
or projector until the correct device image is projected. If a projected image fails to appear, see the next section for help.
Once you see your image, turn to page 37 for instructions on focusing and making other image adjustments.

What To Do If You See a Blank Screen

If you see a blank screen or a blue screen with the message No Signal after turning on your computer or video source, try the following:
Make sure the cables are connected correctly, as described in
Chapter 1.
Make sure the power light is green and not flashing and the lens
cap is off.
Make sure you’ve selected the correct image source; see the
previous section. Allow a few seconds for the projector to sync up after pressing the button.
Check the Signal menu to make sure the correct input source is
selected. See page 56.
34 Projecting
Page 35
If you’re using a PC laptop:
Hold down the Fn key and press the function key that lets you
display on an external monitor. It may have an icon such as or it may be labelled projector to sync up after pressing it. Check your laptop’s manual or online help for details.
CRT/LCD. Allow a few seconds for the
On most systems, the or
CRT/LCD key lets you toggle
between the LCD screen and the projector, or display on both at the same time.
If you’re projecting from a laptop, and you don’t see the same
image on the projection screen and computer screen, check your monitor settings to make sure both the LCD screen and the external monitor port are enabled.
From the Control Panel, open the
Settings tab, then click Advanced. The method for adjusting
the settings varies by brand; you may need to click a
Display utility. Click the
Monitor tab,
then make sure the external Monitor port is set as your primary display and/or enabled. See your computer’s documentation or online help for details.
If you’re using a Macintosh laptop with OS X:
You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps:
1. From the Apple menu, select
Display or Displays.
System Preferences, then click
2. Select VGA Display or Color LCD, click Arrange or
Arrangement, and make sure Mirror Displays is checked.
Click here
Select Mirror Displays
Projecting 35
Page 36
If you’re using a Macintosh laptop with OS 9:
You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps:
1. From the Apple menu, select
Control Panels, then click
Monitors or Monitors and Sound.
2. Click the Arrange icon.
Click here
Drag one monitor icon on top of the other
3. Drag one monitor icon on top of the other.
Arrange option isn’t available, you may need to select one of
If the the Simulscan resolution settings:
1. Click the
Monitor icon, if necessary.
36 Projecting
Click here
2. Select a
Simulscan resolution, as shown. (Allow a few seconds
for the projector to sync up after making the selection.)
Select a Simulscan resolution
Page 37

Adjusting the Image

Once you see your image, you’ll need to make certain adjustments:
To focus or zoom your image, below.
If the image is too high or too low, you can reposition it.
See page 38.
If the image isn’t square, see page 39.
To adjust image brightness, see page 39.
If a computer image displays incorrectly, see page 40.
To change the color mode for your image and surroundings, see
page 40.
You can make many other adjustments to the image—such as changing the brightness, contrast, and aspect ratio—using the projector’s menu system. See Chapter 4 for more information.

Focusing and Zooming Your Image

Rotate the focus ring to sharpen the image.
Focus ring
Rotate the zoom ring to reduce or enlarge the image.
Zoom ring
You can also change the image size by moving the projector closer to or farther away from the screen. You can use the
E-Zoom buttons on
the remote control to zoom in on a portion of the image. See page 45 for instructions.
Projecting 37
Page 38

Adjusting the Height of Your Image

If the image is too low, you can raise it by extending the projector’s front adjustable foot.
1. Stand behind the projector. Press up on the blue foot release lever and lift the front of the projector to extend the front adjustable foot.
2. Once the image is positioned where you want, release the lever to lock the foot in position.
Foot
38 Projecting
3. To fine-tune the height of the image, rotate the foot at the back of the projector.
If the image is no longer rectangular after raising it, see the next section.
Page 39

Adjusting the Image Shape

If the projector is tilted up or down, the images that are displayed will be distorted. To correct the distortion or “keystone” shape, do one or more of the following:
If your image looks like or , you’ve placed the projector
off to one side of the screen, at an angle. Move it directly in front of the center of the screen, facing the screen squarely.
If your image looks like or , you need to adjust the
keystone correction value. Press the or buttons on the projector to correct the shape of the image. After correction, your image will be slightly smaller.
You can also make keystone adjustments using the projector’s Settings menu. See page 59.

Adjusting the Brightness

The brightness of an image depends on the source you are projecting and the amount of light in the room. If the image is too bright or not bright enough, here are two ways you can adjust it:
Change the Brightness setting in the Image menu. See page 54.
Select Low or High for the Brightness Control option in the
Settings menu. (See page 59.) Low brightness mode extends the life of the lamp and decreases the fan noise.
Projecting 39
Page 40

Correcting Computer Images

If you’ve connected a computer and the image doesn’t look right, or it doesn’t fit properly on the screen, press the
Auto button on the
remote control. This automatically resets the projector’s tracking, sync, resolution, and position settings. You must be projecting a computer image for this button to have any effect. Additionally, if the
Auto Setup option in the Signal menu is set to OFF, the Auto
function will not work. See page 57.

Adjusting the Color Mode

Color Mode button
Auto button
You may want to adjust the color mode to select a different setting that is appropriate for the image you’re projecting and the environment in which you’re projecting it.
If you’re projecting computer or RGB video images, the default color mode is
Presentation, which is appropriate for presentations in
bright rooms.
The following table lists the color modes available.
Color mode Description
Photo Best for projecting still images with vivid color in a
bright room (Computer input only).
Sports Best for watching TV in a bright room (component,
S-video, or composite video input only).
Presentation Use when you’re projecting a presentation in a
bright room.
Theatre Use when projecting movies in a dark room.
Game Best for playing video games in a bright room.
sRGB Use when projecting computer images conforming to
the sRGB color standard.
40 Projecting
Blackboard Choose this fixed color mode when you need to
project against a green blackboard.
Page 41
To change the color mode, press the Color Mode button on the
f
remote control until you see the mode you want. The currently selected setting appears in the upper right corner of the screen. You can also use the projector menu system to change the color mode in the Image menu (see page 54).

Adjusting the Volume

You can use the buttons on the remote control or projector to increase or decrease the volume the projector’s built-in speaker. Press the button to increase the volume, or the button to decrease it. A volume gauge appears on the screen while the volume is being adjusted.
Volume controls
note
You can also adjust the volume using the projector’s Settings menu. See page 58 for details.

Shutting Down the Projector

When you’ve finished using the projector, follow the recommended procedure to shut it down.
1. If you’re using a computer, shut it down first; otherwise you may not be able to see your computer’s display to shut it down properly.
2. To turn off the projector, press the P projector or remote control.
You see this confirmation message: (If you don’t want to turn it off, press any other button or wait a few seconds until it disappears.)
Power button on the
note
When the projector has not received any input signals for 30 minutes, it automatically turns off the projector lamp and enters “sleep mode.” This conserves electricity, cools the projector, and extends the life of the lamp. If you are done using the projector, unplug the power cord. If you want to start projecting again, press the P
Power button. You
can turn sleep mode on or of through the Extended menu. See page 61.
Projecting 41
Page 42
3. Press the P
Power button again. The projector beeps twice, the
lamp is turned off, and the power light turns orange.
With Epson’s exclusive Instant Off
technology there’s no cool-down period, so you can pack up and go immediately after turning off the projector.
caution
To avoid damaging the projector or lamp, never unplug the power cord when the power light is green or flashing orange.
If you want to turn the projector on again, press the P
Power
button.
4. Press up on the blue foot release lever and lower the projector to retract the front adjustable foot, as shown.
Foot
5. Replace the lens cap and unplug the power cord.
6. Turn off and disconnect any equipment plugged into the projector.
7. If you won’t be using the projector for awhile, store it in the soft case that came with it or in a protective case.
42 Projecting
Page 43

Using the Remote Control

The remote control lets you access your projector’s features from
anywhere in the room—up to 20 feet away. For example, you can turn the projector on and off, freeze the presentation, zoom in on a portion of your image, and access the menu system. (The projector menus let you adjust many projector settings; see Chapter 4.)
If you’re using a computer and you’ve connected a USB cable as described in Chapter 1, you can use the remote control as a wireless mouse.
When using the remote control, stand within 20 feet of the projector. Point the remote control either at the front or back of the projector or at the screen (the projector’s front sensor can detect signals bounced off the screen). Press the button for the function you want to use.
33
This chapter covers the following information:
Controlling the picture and sound
Using the remote control as a wireless mouse
Replacing the remote control batteries
43
Page 44

Controlling the Picture and Sound

You can use the remote control to select your source, temporarily turn off the picture and sound, freeze the action, or zoom in on the picture. Make sure you have set up your projector and connected any equipment as described in Chapter 1.

Switching Between Picture Sources

Select a source
Move through all the input sources in sequence
If you’ve connected your projector to more than one computer and/or video source, you can use the buttons on the remote control to switch between the different sources.
Press the Comp button to select the computer or video source
connected to the projector’s
Computer(Component Video)
port.
Press the S-Video button to select a video source connected to the
projector’s
Press the Video button to select a video source connected to the
projector’s
Press the Source Search button to move successively through all
S-Video port.
Video port.
of the input sources.
After you select a source, the screen goes dark for a moment before the image appears. The name of the selected source (such as
S-Video) appears briefly on the screen.
Computer or
44 Using the Remote Control
Page 45

Turning Off the Picture and Sound

Press the A/V Mute button on the remote control to turn off the image and sound and darken your screen. This is useful if you want to temporarily re-direct your audience’s attention without the distraction of a bright screen.
To turn off the picture and sound, press the A/V Mute button.
The screen goes dark.
To turn the image and sound back on, press the button again, or
Esc.
press
You can create an image, such as a company logo or a picture, to display on the screen whenever you press the
A/V Mute button. See
page 64 for more information.

Stopping Action

Press the Freeze button to stop the action in your video or computer image and keep the current image on the screen. The sound will continue, however. Also, because the source continues to transmit signals, you won’t resume the action from the point you paused it.
Press the
Freeze button again or press Esc to restart it.

Zooming Your Image

Follow these steps to zoom in on a portion of the image:
1. Press the
You see a crosshair indicating the center of the zoom-in area.
2. Use the pointer button to position the crosshair in the area you want to enlarge.
E-Zoom button on the remote control.
Zoom inEsc
Zoom out
FreezeA/V Mute
3. Continue pressing the area up to 4 times.
E-Zoom button to enlarge the selected
Using the Remote Control 45
Page 46
4. While the image is enlarged, you can:
Use the pointer button to pan about.
Press the E-Zoom button to zoom out.
note
You must be projecting component, composite, or S-Video images to change the aspect ratio.
You can also change the aspect ratio using the projector’s Signal menu. See page 56 for details.
5. When you’re done, press the
ESC button to return to the original
size.

Changing the Image’s Aspect Ratio

If you’re projecting a widescreen format image, you can use the
Resize button on the remote control to change the aspect ratio.
Follow these steps:
1. Press the for widescreen format.
2. Press it again to return to 4:3 aspect ratio.
Resize button once to change the aspect ratio to 16:9
46 Using the Remote Control
Page 47

Using the Remote Control as a Wireless Mouse

When you use the remote control as a wireless mouse, you can control your computer or click through slide show-style presentations (such as PowerPoint) from up to 20 feet away. This gives you more flexibility, since you don’t need to stand near your computer to change slides.
To control your computer with the remote, make sure you have connected your computer to the projector with a USB cable as described on page 21.
To display the mouse pointer, press the Pointer button.
To move the pointer on the screen, aim the remote at the screen
and use the pointer button.
To click (or left-click), press the Enter button.
To right-click, press the Esc button.
To double-click, press the Enter button twice.
To click and drag, press down and hold the Enter button and use
the pointer button to move where you want to drag.
To advance slides in a PowerPoint presentation in Slide Show
mode, press the Press the
Page up or Enter button on the remote control.
Page down or Esc button to go back a slide.
Left-click or double-click
pointer
Move the pointer
Right-clickDisplay the
Page upPage down
Using the Remote Control 47
Page 48
note
The remote control automatically shuts off when it detects a button being pressed more than 30 seconds. This conserves battery life. It can be helpful, for example, when the remote is in a carrying case and the
P
Power button is
accidentally pushed.
caution
When replacing batteries, take the following precautions:
Replace the batteries as
soon as they run out. If a battery leaks, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately.
Do not expose batteries to
heat or flame.
Dispose of used batteries
according to local regulations.
Remove the batteries if you
won’t be using the remote control for a long period of time.

Replacing the Batteries

The remote control uses two AAA alkaline batteries. Follow these steps when you need to replace them:
1. Press in the tab to remove the battery cover.
2. Remove the old batteries, then insert the new ones as shown.
3. Replace the battery cover. (It should click into place.)
48 Using the Remote Control
Page 49

Fine-tuning the Projector

You can use the Menu button on the projector or remote control to
access on-screen menus to adjust the image, sound, and other features. This chapter covers the following information:
Using the menu system
Adjusting image colors and clarity
Adjusting the input signal
Customizing projector features
Selecting projector setup options
Viewing lamp usage and other information
Using the projector’s security features
433
Restoring the default settings
49
Page 50

Using the Projector’s Menu System

The six projector menus let you adjust and customize the projector features:
The Image menu lets you modify the colors of the projected
image and fine-tune brightness, contrast, and sharpness.
The Signal menu lets you make adjustments to the input signal.
You can select your input source, change the image position and aspect ratio, and adjust tracking and sync for computer images.
The Settings menu lets you customize the way you use the
projector. It allows you to adjust the volume and keystone correction, set lamp brightness to high or low, select the shape of the mouse pointer, and disable buttons on the projector while you are projecting.
The Extended menu lets you customize the way you set up the
projector. Among the options, you can select the menu language, set rear or ceiling projection, and record a custom image or logo to be displayed as the startup screen or whenever you press the
A/V Mute button on the remote control.
50 Fine-tuning the Projector
The Info menu provides information about lamp status and
computer or video settings.
The Reset menu lets you restore the projector’s factory default
settings.
Page 51

Changing Menu Settings

Use the buttons on the remote control to access the menus and change settings. Follow these steps:
1. Press the
Menu button on the remote control or projector to
display the menu screen:
Menu options
Menus
The six menus are listed on the left, and the options available for the highlighted menu are shown on the right.
2. Use the pointer button on the remote control or the up and down arrow buttons on the projector to scroll through the menu list. When you’ve highlighted the desired menu, press the
Enter
button to select it.
Menu button Esc button
Enter button Arrow buttons
Pointer button
The highlight moves to the first option for that menu.
3. Use the pointer button or the up and down arrow buttons to scroll through the list of options. (The options available depend on which source is selected.)
Esc buttonEnter button
Fine-tuning the Projector 51
Page 52
4. After highlighting the option you want to adjust, use the pointer button on the remote control or left or right arrow
buttons on the projector to change the setting. In some cases, you may have to press the
Enter button to see a sub-screen for
changing the setting.
Press the left or right side of the pointer button or the left
or right arrow buttons on the projector to adjust a slider bar.
To select from two or more settings, use the pointer
button or arrow buttons to highlight the desired setting, then press
Enter.
5. Press the
Esc button to return to the previous menu or to close
the menu system if you are at the main menu. Your changes are saved automatically.
6. Press the
Menu button to exit the menu system.
52 Fine-tuning the Projector
Page 53

Adjusting Colors and Clarity

The Image menu lets you make adjustments to the colors of the projected image and fine-tune brightness, contrast, and sharpness. The options available depend on which image source is selected:
Computer (analog-RGB) and RGB video
Component, composite, and S-Video
Follow these steps to adjust the appearance of your image:
1. Press the
2. Press
Menu button. You see the main menu.
Enter to select the Image menu.
Fine-tuning the Projector 53
Page 54
3. Use the pointer button (or the up and down arrow buttons)
and press
Color Mode
Enter to select any of the following options:
Corrects the vividness of image color. You can select from the following settings, and save a different one for each computer and/or video source:
Photo: For projecting still images with vivid color in a bright
room (Computer input only).
Sports: For watching TV in a bright room (component,
S-Video, or composite video input only).
Presentation: For presentations in a bright room.
Theatre: For optimizing movie images with natural color in a
dark room (the default for video or S-Video display).
Game: For playing video games in a bright room.
sRGB: For standard sRGB computer displays (the default
when projecting from a computer with analog video).
Blackboard: Fixed color mode for projecting against a green
blackboard.
note
You can also select High or
Low brightness mode in the
Settings menu. See page 59.
54 Fine-tuning the Projector
Brightness
Lightens or darkens the overall image.
Contrast
Adjusts the difference between light and dark areas.
Color Saturation (component, composite, and S-Video)
Adjusts the depth or intensity of the image colors.
Tint (component, composite, and S-Video)
Adjusts the balance of green to magenta in the image.
Page 55
Sharpness
Sharpens or softens the image.
Color Temp.
Adjusts red and blue tones. A lower color temperature produces an image with more red (warmer tones), while a higher color temperature produces an image with more blue (cooler tones).
Color Adjustment
Adjusts the intensity of red, green, and blue.
4. When the image is set correctly, press are automatically saved.
Esc or Menu. Your settings
Fine-tuning the Projector 55
Page 56

Adjusting the Input Signal

Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to make manual adjustments. In addition to changing the position of the projected image, you can correct tracking and sync for computer images, or change the aspect ratio to widescreen format for video images.
1. Press the
2. Select the
Computer (analog-RGB) and RGB video
Menu button. You see the Image menu.
Signal menu. You see one of the following screens:
56 Fine-tuning the Projector
Component video
Composite video and S-Video
Page 57
3. Press Enter. Then use the pointer button (or up and down arrow buttons) and the
Enter button to select any of the
following options:
Auto Setup (computer images)
Leave this setting
ON to automatically optimize the computer
image. Turn it off if you want to save adjustments you have made to the video settings.
Tracking (computer images)
Removes unwanted vertical lines from a computer image by matching the projector’s internal clock to various computer signals. See page 88 for more information about adjusting the tracking.
Sync (computer images)
Corrects fuzziness or screen flicker by synchronizing the projector with the tracking signal sent from the computer. See page 88 for more information about adjusting the sync setting.
Position
Use the pointer button or arrow buttons to move the image on the screen left, right, up, or down.
note
If you have repositioned the image but then change your mind, you can press the
Auto button on the remote
control to restore the default settings.
Progressive
Leave this setting ON when viewing S-Video or composite video so that interlaced-to-progressive conversion is carried out (best for fast-moving pictures). If you notice flickering while viewing still images, switch this setting to
Computer Input
OFF.
Selects the signal from equipment connected to the
Computer(Component Video) port. If your image colors
look wrong, try changing this setting from following:
Component Video for component video sources.
RGB for computer or RGB video sources, or
Auto to one of the
Fine-tuning the Projector 57
Page 58
Video Signal (composite and S-Video)
Leave this setting at system (select
Resize (video)
Auto unless you are using a 60-Hz PAL
PAL60).
Sets the image’s aspect ratio (ratio of width to height) to for letterbox video content and to
16:9 for widescreen video
content.
4:3
4. When you’re finished adjusting the signal settings, press
Menu.
Esc or

Customizing Projector Features

The Settings menu lets you customize the way you use the projector, from adjusting lamp brightness and speaker volume to changing the shape of the mouse pointer.
1. Press the
2. Select the
Menu button.
Settings menu.
58 Fine-tuning the Projector
Page 59
3. Press Enter. Then use the pointer button (or up and down arrow buttons) and the
Keystone
Enter button to set the following options:
Adjusts a distorted image from a trapezoid shape to rectangular.
Operation Lock
When turned on, this function disables all projector buttons except the P
Power button. Changes to this setting take
effect after you restart the projector. (After you turn off the projector, wait for the Ppower light to turn a steady orange before turning it on again.)
Pointer Shape
Lets you select from three different pointer shapes. The Password Protect function must be cancelled first. See page 66.
Brightness Control
Select Low lamp brightness when the projection is too bright for the room. The
Low setting also reduces electricity
consumption and fan noise. Select maximum brightness. (Also check the the Image menu; see page 54.)
Volume
Adjusts the volume for the projector’s speaker.
4. When you’re finished, press
High to project the
Esc or Menu.
Brightness setting in
note
To cancel the Operation Lock function from the projector, press the button for about seven seconds.
Enter
Fine-tuning the Projector 59
Page 60

Selecting Projector Setup Options

Use the Extended menu to customize the way you set up the projector. You can configure the projector for rear and/or ceiling projection, change the language for the menus and messages, set the screen background color, and capture and store a custom image or logo for the startup screen.
note
The Startup Screen option cannot be turned off if the User’s Logo Protect feature has been turned on. See page 66.
1. Press the
2. Select the
Menu button.
Extended menu. You see the features and their settings
on the right side:
3. Press
Enter. Then use the pointer button (or the up and down
arrow buttons) and the
Display
Message:
Background Color: Sets the screen background to Black, Blue, or Logo when the A/V Mute button is pressed.
Startup Screen: Enables or disables display of the startup
screen when the projector is turned on.
User’s Logo
Turn on to display the image or logo you have captured whenever the projector is turned on. See page 64 for more information.
Enter button to set the following options:
Lets you turn screen messages on or off.
60 Fine-tuning the Projector
Page 61
Projection
Projector is in front of the screen.
Front:
Front/Ceiling: Projector is in front of the screen, mounted
upside-down from the ceiling.
Rear: Projector is behind the screen.
Rear/Ceiling: Projector is behind the screen, mounted
upside-down from the ceiling.
Operation
Direct Power:
When this feature is enabled, projection starts
as soon as you plug in the power cord. You don’t have to press the P
Sleep Mode: When Sleep Mode is on, the projector turns
Power button.
off the lamp if it has not received any input signals for 30 minutes.
High Altitude Mode: When using the projector at an
altitude above 4,921 feet, turn this setting on to ensure that the internal temperature of the projector is regulated properly. Turn this setting off for lower elevations.
Link 21L
Turn this setting on only if you’re controlling the projector from a computer with the EMP Link 21L software. This software can be downloaded from the Epson website at support.epson.com. (You must turn the projector off and then on again to use the new setting.)
Language
Select the language to be used for the projector menus.
note
When Direct Power is turned on, press the P
Power button to turn
the projector off, wait until the P power light turns a steady orange, then unplug the power cord.
4. When you’re finished, press
Esc or Menu.
Fine-tuning the Projector 61
Page 62
Viewing Lamp Usage and Other
note
You can make changes to many of the signal settings on the Signal menu. See page 56 for details.
note
The lamp usage timer doesn’t register until you’ve used the lamp for at least 10 hours.
Information
Use the Info menu to view information about the display settings of your computer and the number of hours the lamp has been used.
1. Press the the following menus:
Computer (analog RGB, digital RGB, RGB Video/Component video, YCbCr, YPbPr)
Menu button and select the Info menu. You see one of
62 Fine-tuning the Projector
Video (Composite video, S-Video)
Lamp Hours
Displays the number of hours the lamp has been used. The life span of the lamp ranges from about 2000 hours in brightness mode to about 3000 hours in
Low brightness
mode. If the number shown is close to 2000 or the information is displayed in red, make sure you have a spare lamp handy.
High
Page 63
Source
Displays the input source currently being projected.
Input Signal (computer, RGB video, and component video)
Displays the input signal setting.
Resolution (computer, RGB video, and component video)
Displays the input resolution.
Video Signal (composite and S-Video)
Displays the video signal format.
Refresh Rate (computer, RGB video, and component video)
Displays the refresh rate.
Sync Info (computer, RGB video, and component video)
Provides information that may be needed by the service technician.
2. When you’re finished, press
Esc or Menu.

Using the Projector’s Security Features

To prevent unauthorized use of the projector, you can do the following:
Create an identifying user logo that is displayed at startup and/or
when the
Assign a password; this can be disabled for a set period if you want
to loan the projector to someone
Disable the projector’s buttons; this is useful, for example, if
you’re projecting in a classroom and you want to ensure that no one touches the projector’s buttons while you’re using the remote control
If you create a user’s logo for the projector, you can lock the logo on so it is displayed as the startup screen and/or AV/Mute screen. Unauthorized users cannot turn it off or change it. This feature is intended to discourage theft and provides a way to identify the projector should it be stolen.
A/V Mute button is pressed
Fine-tuning the Projector 63
Page 64
note
If you should happen to enable the password before you set one and you see the prompt to enter the password, enter the default password 0000 to proceed.
If you assign the projector a password, a screen appears requesting the password whenever the projector is turned on. If you enter the password incorrectly three times in succession, the projector’s operation is locked and you’ll need to disconnect the power cord, then reconnect it to redisplay the password screen. If an incorrect password is entered 30 times in a row, the projector is locked and you’ll need to contact Epson to unlock it. See “Where To Get Help” on page 92.
If someone else will be using the projector for awhile but you want to make sure that person returns it by a certain time, you can temporarily disable the password for a set period. When that time has elapsed, the password is reactivated and must be entered before the projector can be used.
When you enable the Operation Lock feature, all of the projector’s buttons are disabled except the P
Power button.

Creating Your Own Screen Logo

You can transfer any image on your computer to the projector, and then use it as the startup screen and/or the screen that is displayed when you press the A/V Mute button. The image can be a company logo, slogan, photograph, or any other image you want to use. The projector considers this image the “User’s Logo.”
note
If the User’s Logo Protect function is message that the logo cannot be recorded. You’ll need to disable the User’s Logo Protect function before you can create or change the User’s Logo. See page 66.
64 Fine-tuning the Projector
ON, you see a
Follow these steps to capture the image and transfer it to the projector:
1. Display the image you want to use on the projector. You can use an image from either a computer or video source, such as a VCR.
2. Press the
Menu button and select the Extended menu.
Page 65
3. Use the pointer button (or the down arrow button) and press
Enter to select User’s Logo.
4. When you see a message asking if you want to use the present image as a user’s logo, select
Yes and press Enter. A selection box
displays over the image.
5. Use the pointer button on the remote control or the arrow buttons on the projector to select the area of the image you want to use. Once you have selected the area, press
Enter.
6. When you see the message press
Enter. If you want to change the area selected, select No,
press
Enter and repeat steps 5 and 6.
Select this image?, choose Yes and
7. When you see this screen, select a zoom rate (display size), and then press
8. When you see the message
Yes and press Enter. Saving the logo takes a few moments. Do
Enter.
Save image as user’s logo?, select
not use the projector or other sources (computer, video, etc.) while the logo is being saved.
9. When you see the message
Completed, press Esc.
10. To display the logo as the background screen when the A/V Mute button is press, select the
11. Select
Background Color and press Enter. Then select Logo and
press
Enter.
12. When you’re finished, press
Display menu and press Enter.
Menu to exit the menus.
note
The default setting for the
Startup Screen option in
the
Display menu is ON. If
the
Startup Screen is set to
OFF, the logo will not
display at startup.
If the User’s Logo Protect function has been set to the
Background Color
setting cannot be changed. You need to turn the protect function off first. See page 66 for details.
Once you’ve saved a user’s logo, you cannot reset the logo setting to its factory default (no logo).
ON,
Fine-tuning the Projector 65
Page 66
note
If a password has already been set, you see the Password Protect Release screen. See “Starting the Projector with a Password” on page 67.

Setting a Password

1. Press the Freeze button on the remote control for about 7 seconds until you see the Password Protect menu:
Hold down this button to activate the numeric keypad
Use these buttons like a numeric keypad to enter the password
2. Select
3. Select
4. Hold down the
Password and press Enter. You see the message Change
the password?
Yes and press Enter.
Num key on the remote control and use the
numeric keypad to enter a 4-digit password.
The password will be displayed as
****. After you enter the last
digit, a confirmation screen appears. Enter the password again.
5. After you finish setting the password, press the
Esc button to
return to the Password Protect menu.
Make a note of the password and keep it in a safe place in case you forget it.

Turning On the Password and User’s Logo

1. Press the Freeze button on the remote control for about 7 seconds until you see the Password Protect menu.
2. To enable the password, select
Enter. Select ON then press Esc.
3. If you want to disable the password temporarily, select press
Enter. Then hold down the Num button while you use the
numeric keypad to enter the number of hours (from 0 to 9999) that you want the password feature disabled. If you want the projector to request the password every time it is turned on, set the timer to
0H.
Power ON Protect and press
Timer and
66 Fine-tuning the Projector
Page 67
The countdown for the elapsed time begins as soon as you close the Password Protect menu. (You can check the elapsed time in this menu next to
Time elapsed.)
4. To enable your screen logo, select
Enter. Select ON and press Enter.
User’s Logo Protect and press
When this feature is on the logo appears whenever the projector is turned on (if the
Startup Screen is enabled in the Extended
menu; see page 60) and as the A/V Mute screen (if you selected the
Logo as the Background Color in the Extended menu).
None of the User’s Logo features can be changed when the User’s Logo Protect function is enabled.
5. Press
Menu to close the Password Protect menu.
If you lose the remote control, you will not be able to enter the password, so keep the remote control in a safe place at all times.
When the period defined in the Time-elapsed setting has passed, and the password is entered correctly, the elapsed time will be reset to
0
and the countdown will start again. Remember to disable or change this setting when you need to.

Starting the Projector with a Password

When the password function is enabled, you see this screen when you turn on the projector:
Press down the
Num button on the remote control as you use the
numeric keypad buttons to enter the password. Once you have entered the password correctly, the password screen closes, and projection begins.
Fine-tuning the Projector 67
Page 68
note
To cancel Operation Lock, press the projector’s button for seven seconds.
Enter
If the password is not correct, you see the message
Please try again.
succession, you see the message
locked. Request code xxxxx
If you enter an incorrect password three times in
The projector’s operation will be
and the projector switches to standby
Wrong password.
mode for approximately 5 minutes. Write down the request code. Then disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on.
When you see the Password Protect Release screen again, you can try to enter the correct password.
If you have forgotten the password, contact Epson with the request code number that appears in the Password Protect Release screen for assistance. See “Where To Get Help” on page 92.
If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson to unlock it.

Disabling the Projector’s Buttons

When you enable the Operation Lock function, all the projector’s buttons are disabled except for the P
1. Press the
2. Select the
Menu button.
Settings menu and press Enter.
Power button.
68 Fine-tuning the Projector
3. Use the pointer button (or up and down arrow buttons) to
Operation Lock and press the Enter button.
select
4. Select
5. Select
6. Press the
ON and press Enter.
Yes and press Enter to confirm the setting.
Menu button.
Page 69

Restoring the Default Settings

The Reset menu lets you return most projector menu settings to their default values. It also lets you reset the lamp hours to their initial default value; see page 77 for instructions on resetting the lamp timer.
To reset most projector menu settings, select
Enter button to display the confirmation screen. Select Yes to reset all
the default settings or
No to cancel.
Reset All and press the
note
The input signal, Video Signal, User’s Logo, and Language settings do not return to their defaults when you select the input signal or video signal, use the on the Signal menu; see page 56 for details. To reset the User’s Logo and Language settings, use the
Reset option on the
Extended menu; see page 60 for details.
Reset All. To reset
Reset option
Fine-tuning the Projector 69
Page 70
70 Fine-tuning the Projector
Page 71
warning
Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically explained in this User’s Guide. Refer all other servicing to qualified service personnel.
5

Maintaining and Transporting the Projector

Your projector needs little maintenance. All you need to do on a
regular basis is keep the lens clean. Any dirt or smears on the lens may show up on your projected image.
You also need to periodically clean the air filter and the air intake and exhaust vents. A clogged air filter or air vent can block ventilation needed to cool the projector and cause overheating.
The only parts you should replace are the lamp and air filter. If any other part needs replacing, contact your dealer or a qualified servicer.
This chapter covers the following:
Cleaning the lens
Cleaning the projector case
Cleaning and replacing the air filter
Replacing the lamp
Resetting the lamp timer
Transporting the projector
71
Page 72

Cleaning the Lens

Clean the lens whenever you notice dirt or dust on the surface.
Use a canister of compressed air to remove dust.
caution
Do not use glass cleaner to clean the lens.
To remove dirt or smears on the lens, use lens-cleaning paper. If
necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface.

Cleaning the Projector Case

Before you clean the case, first turn off the projector and unplug the power cord.
To remove dirt or dust, wipe the case with a soft, dry, lint-free
cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water
and a mild detergent. Then wipe the case.
Do not use wax, alcohol, benzene, paint thinner, or other
chemical detergents. These can damage the case.
72 Maintaining and Transporting the Projector
Page 73

Cleaning and Replacing the Air Filter

Clean the air filter and air intake and exhaust vent on the bottom of the projector after every 100 hours of use. If they are not cleaned periodically, they can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. When the filter and vent are clogged, the projector displays the message
To clean the air filter and air vent, follow these steps:
1. Turn off the projector, allow it to cool down, and unplug the
2. Turn the projector upside-down and clean the filter and air intake
The projector is overheated.
power cord.
vent on the base of the projector.
To clean the filter and air vent, Epson recommends using a small vacuum cleaner designed for computers and other office equipment. If you don’t have one, gently clean them using a very soft brush (such as an artist’s brush).
Air vent
Air filter
If the dirt is difficult to remove or if the filter is torn, replace it. Contact your dealer or call Epson at (800) 873-7766 to obtain a new one. The air filter set (part number V13H134A08) contains two filters. In Canada, please call (800) 463-7766 to locate a dealer.
Maintaining and Transporting the Projector 73
Page 74
3. If you need to replace the filter, slide it off, as shown.
4. Align the new filter carefully as you slide it into place. It should click into place.
74 Maintaining and Transporting the Projector
Page 75

Replacing the Lamp

The projection lamp typically lasts for about 2000 hours of use (in high brightness mode) or 3000 hours (in low brightness mode). It is time to replace the lamp when:
The projected image gets darker or starts to deteriorate.
The lamp light is flashing orange.
The message Replace the Lamp appears on the screen when the
lamp comes on. To maintain projector brightness and image quality, replace the lamp as soon as possible.
Contact your dealer or call Epson at (800) 873-7766 in the United States for a replacement lamp. Request part number V13H010L34. In Canada, please call (800) 463-7766 to locate a dealer.
note
You can check to see how many hours the lamp has been used. See page 62.
Turn the projector off when not in use. Continuous 24-hour-a-day use may reduce the overall life of this product.
Follow these steps to replace the lamp:
1. Press the P
Power button twice to turn off the projector. When
you hear the projector beep twice, unplug the power cord.
2. If the projector has been on, allow it to cool down for at least an hour (or until the lamp is cool).
3. Use the screwdriver included with the replacement lamp to loosen the screw holding the lamp cover (the lamp cover is located on top of the projector).
4. Slide the cover out, then lift it off.
warning
Let the lamp cool before replacing it. If the lamp breaks, handle the shards carefully to avoid injury.
Maintaining and Transporting the Projector 75
Page 76
5. Use the screwdriver to loosen the two screws holding the lamp in place. (You can’t remove the screws.)
Don’t remove these screws
note
The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
caution
Do not touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure.
note
Be sure to seat the lamp fully and secure the lamp cover. If the lamp is not properly installed or the cover is loose, the lamp will not turn on.
6. Hold the lamp as shown and pull it straight out.
7. Gently insert the new lamp. If it doesn’t fit easily, make sure it’s facing the correct way.
8. Once the lamp is fully inserted, tighten its screws.
76 Maintaining and Transporting the Projector
Page 77
9. Lower the lamp cover into place. (The opening should be almost covered, and the top of the cover should be flush with the top of the projector.) Then slide the cover closed and tighten the screw.
10. Reset the lamp timer as described in the next section.

Resetting the Lamp Timer

You must reset the lamp timer after replacing the lamp to clear the
Replace the Lamp warning message. Follow these steps:
1. Connect the power cable and turn on the projector.
2. Press the select the
3. Select the the following:
Menu button on the remote control or projector and
Reset menu. Then press Enter. You see the following:
Lamp-Hours Reset option and press Enter. You see
note
Do not reset the lamp timer if you have not replaced the lamp. If you do, the Lamp Hours will not accurately reflect the number of hours that the lamp has been used.
Esc button
Enter button Menu button
Maintaining and Transporting the Projector 77
Page 78
Menu button Esc button
4. Select
Yes and press Enter.
Enter button
note
Epson shall not be liable for any damages incurred during transportation.
5. Press
Esc to return to the main menu or the Menu button to exit
the menu system.

Transporting the Projector

The projector contains many glass and precision parts. If you need to transport it, please follow these packing guidelines to prevent damage to the projector:
When shipping the projector for repairs, use the original
packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.
When transporting the projector as freight or checked luggage,
first put it in the supplied carrying case, then pack it in a firm box, using cushioning around the case.
When you are hand-carrying the projector, be sure to use the
supplied carrying case.
78 Maintaining and Transporting the Projector
Page 79

Solving Problems

This chapter helps you solve problems with your projector, and tells
you how to contact technical support for problems you can’t solve yourself. This chapter explains the following:
Using the projector’s on-screen help system
What to do when the projector’s status lights flash
Solving problems with the image or sound
Solving password problems
Solving problems with the remote control
Contacting technical support
6
79
Page 80

Using On-Screen Help

If the image doesn’t look right or your audio isn’t working, you can get help by pressing the control. The following choices are available:
No signal or image appears on the screen
Problems with sound
Language change
Follow these steps to get help:
? Help button on the projector or remote
Press to return to the last menu
Press to confirm selection
Use to select a problem or solution
Help button
1. Press the
? Help button on the remote control or projector. You
see the help menu.
Press to confirm selection
Press to return to the last menu
Help button
Press one of these buttons to select a problem or solution
2. Use the pointer button on the remote control or the up and down arrow buttons on the projector to select an option. Then press the
Enter button to select it.
3. Use the pointer button on the remote control or the up and down arrow buttons on the projector to highlight the problem you want to solve. Then press the
Enter button to view the
solution(s).
80 Solving Problems
Page 81
4. Highlight a solution (if this choice is available). Then press the
Enter button to select the solution.
Press the
Esc button if you need to back up.
If the solution is to adjust one of the settings, use the pointer button on the remote control or the left and right arrow buttons on the projector to adjust it.
5. To exit the Help system, press the
? Help button.
If none of the suggestions solves your problem, see additional solutions to problems in the following sections.

What To Do When the Lights Flash

The lights on top of the projector indicate the projector’s status and let you know when a problem occurs.
Lamp light
Power light
Temperature light
If the projector is not working correctly, first turn it off and unplug it. Then plug the power cord back in and turn on the projector. If this does not solve the problem, check the status lights on top of the projector and try the solutions recommended in the following table.
Solving Problems 81
Page 82
Power light
Red Flashing red Flashing red There is an internal error in the projector. Turn the
Red Off Flashing red There is a problem with the fan or a sensor. Turn
Red Flashing red Off The lamp is burned out, broken, or not installed
Flashing orange Off Replace the lamp with a new one as soon as
Red Off Red The projector has overheated and turned itself
Lamp light
Temperature light Description
projector off and unplug it. Contact Epson for help.
the projector off and unplug it. Contact Epson for help.
correctly; or the lamp cover is open. Close the cover or replace or reseat the lamp, if necessary, as described on page 75. If these suggestions don’t work, contact Epson.
possible; see page 75 for instructions. If you continue to use the lamp, there is a risk it may break.
off. Let it cool for about five minutes, then turn it back on. Make sure there is plenty of space around and under the projector for ventilation. Also clean the air filter and air exhaust vents. See page 73. If it continues to overheat, you may need to replace the air filter.
Flashing red Off Flashing orange The projector is too hot. Make sure the
temperature surrounding the projector does not exceed 95 around and under the projector for ventilation. Clean the air filter and air vents, if necessary. See page 73 for instructions.
Orange Off Off The projector is in standby or sleep mode. You
can unplug it or press the P Power button to turn it on.
Flashing green
Green Off Off The projector is operating normally.
Flashing orange
Off Off The projector is warming up. Wait for the image
to appear.
Off Off The projector is shutting down. Wait for the light
to stop flashing and remain orange before unplugging it.
°F (35 °C) and there is plenty of space
82 Solving Problems
Page 83

Solving Problems with the Image or Sound

No image appears on the screen.
Check that the power light is green, not flashing, and the lens cap
is off.
The projector may be in standby or sleep mode. If the projector
has not received any input signal for 30 minutes, it turns off the lamp to conserve the lamp life and save energy. If the power light is orange, press the P
Press the A/V Mute button to make sure the picture has not been
turned off temporarily.
If the power was switched off and then on again, wait until the
power light stops flashing and remains orange; then press the P
Power button again.
Check the Video Signal or Computer Input setting in the
Signal menu to make sure it is correct for the selected source. See page 56 for more information.
Power button to turn the projector on.
Have messages been turned off in the Display setting of the
Extended menu? See page 60 for details.
Adjust the Brightness setting on the Image menu or select High
for the
Brightness Control setting in the Extended menu. See
page 54 or page 59.
The attached computer may be in sleep mode or displaying a
black screen saver. Try pressing a key on the computer.
Nothing appears on the external monitor.
Make sure the VGA computer cable is connected to your
computer’s video port and the projector’s
Computer(Component Video) port. Make sure the cable from
your monitor is connected to the projector’s
Monitor Out port.
Solving Problems 83
Page 84
You see a blue screen with the message No Signal displayed.
Make sure the cables are connected correctly, as described in
Chapter 1.
Make sure the power to your computer or video source is
turned on.
If you’ve connected a computer and one or more video sources,
you may need to press the projector or the
Comp, S-Video, or Video button on the remote
Source Search button on the
control to select the correct source. Allow a few seconds for the projector to sync up after pressing the button.
If you’ve connected a laptop computer, make sure it’s set to
display on an external monitor. See page 35.
If you’re using a PC laptop:
Hold down the Fn key and press the function key that lets you
display on an external monitor. It may have an icon such as
, or it may be labelled the projector to sync up after pressing it. Check your laptop’s manual or online help for details.
CRT/LCD. Allow a few seconds for
84 Solving Problems
On most systems, the or
CRT/LCD key lets you toggle
between the LCD screen and the projector, or display on both at the same time.
Depending on your computer’s video card, you might need to use
the Display utility in the Control Panel to make sure that both the LCD screen and external monitor port are enabled. See your computer’s documentation or online help for details.
If you’re using a PowerBook or iBook with Macintosh OS X:
1. From the Apple menu, select System Preferences, then click
Display or Displays.
2. Select
VGA Display or Color LCD, click Arrange or Arrangement, then put a check mark in Mirror Displays.
Page 85
If you’re using a PowerBook or iBook with Macintosh OS 9:
1. From the Apple menu, select Control Panels, then click
Monitors or Monitors and Sound.
2. Click the Arrange icon.
3. Drag one monitor icon on top of the other. This lets you display on the projector screen as well as the LCD screen.
4. If the
5. Select one of the listed
Arrange icon isn’t available, click the Monitor icon.
Simulscan resolutions. (Allow a few
seconds for the projector to sync up after making the selection.)
The message Not Supported is displayed.
Make sure your computer’s resolution doesn’t exceed XGA and
the frequency is supported by the projector. See page 98. If necessary, change your computer’s resolution setting as described below.
Make sure the correct Video Signal is selected in the Signal
menu. See page 58. It should normally be set to
Auto.
Only part of the computer image is displayed.
If you’re projecting from a computer or RGB video device, press
the
Auto button on the remote control. If this doesn’t work or if
you’re projecting from a component, composite, or S-Video device, you may need to adjust the menu. See page 57 for more information.
If you’ve enlarged part of the image using the E-Zoom button
on the remote control, press the and return to full display.
Position setting in the Signal
Esc button to cancel zooming
Try pressing the Resize button on the remote control to select a
different aspect ratio (ratio of length to height).
Solving Problems 85
Page 86
Make sure your computer’s resolution setting is correct. Ideally,
it should be 1024 × 768 to match the projector’s native resolution. If this option isn’t available, select one of the other compatible video formats listed on page 98.
Windows:
Right-click the desktop, select
Properties, click the Settings
tab, and select a different resolution.
Macintosh OS X:
On the Apple menu, choose click
Display or Displays. Select a different resolution.
Macintosh OS 9.x:
On the Apple menu, choose
Monitors or Monitors and Sound. Select a different
System Preferences, then
Control Panels, then click
resolution.
You also may need to modify existing presentation files if you
created them for a different resolution. See your software documentation for specific information.
The image isn’t rectangular, but trapezoid-shaped.
86 Solving Problems
Make sure the projector isn’t placed off to one side of the screen,
at an angle, or the image won’t be rectangular. Place it directly in front of the center of the screen, facing the screen squarely.
If you’ve tilted the projector upward, the image will be broader at
the top. Hold down the or buttons on top of the projector until the image is rectangular.
The image contains static or noise.
If you’re using a computer cable longer than 6 feet, or an
extension cable, the image quality may be reduced.
Keep your computer and video cables separated from the power
cord as much as possible to prevent interference.
Page 87
The video signal may be split between the computer and the
projector. If you notice a decline in the projected image quality when the image is displayed simultaneously on your laptop computer and the projector, turn off the laptop’s LCD display.
If you’re projecting from a composite or S-Video source, check
Video Signal setting in the Signal menu. In most cases, leave
the it set at this setting to
Make sure the cables are securely connected at both ends.
Select the correct resolution; see “Compatible Video Formats” on
Auto. If you’re using a 60-Hz PAL video source, change
PAL60. See page 58 for details.
page 98.
If you’re projecting from a computer, press the Auto button on
the remote control or the
Enter button on the projector to adjust
tracking and sync automatically. If that doesn’t work, try adjusting the
Sync and Tracking settings in the Signal menu. See
page 57.
The image is blurry.
Adjust the focus using the focus ring.
Make sure the lens cap is off.
There may be dirt or smears on the lens. Clean the lens as
described on page 72.
Make sure the lens is not fogged by condensation. You may need
to wait before using the projector after moving it from a cold environment.
Make sure the projection distance is within the range described on
page 16.
Adjust the Sharpness setting on the Image menu (see page 55).
You should be able to see the effect on the screen immediately.
Solving Problems 87
Page 88
You see vertical stripes or the image still looks blurry after trying the solutions in the previous section.
If you’re projecting from a computer and displaying an image that
contains a lot of fine detail, you may notice one or more vertical stripes or bands, or some of the characters may look heavy or blurred. Press the the projector’s tracking and sync settings.
If further adjustment is needed, you can fine-tune the Tracking
Sync settings manually using the Signal menu as described
and on page 57.
1. Fill the screen with an image containing fine detail when making these adjustments. For example, in Windows you can select a pattern to appear as your desktop background. Or try projecting black text on a white background.
Auto button on the remote control. This resets
note
Because of the different technologies used, your projected image may not exactly match the colors on your laptop or computer monitor.
2. Adjust the
3. Adjust the
Tracking to eliminate vertical stripes.
Sync to increase the sharpness of the image.
The colors of the image are not right.
Try selecting a different Color Mode. See page 54 for
instructions.
If you’re displaying video, adjust the Color Saturation and Tint
settings on the Image menu. See page 54 for instructions.
Adjust the Brightness and Contrast settings on the Image
menu. See page 54.
Try adjusting the Color Adjustment setting on the Image menu.
See page 55.
Make sure the input signal setting on the Signal menu matches
the signal from the connected device. If the image is too purple and you’ve connected a computer or RGB video device to the
Computer(Component Video) port, select Computer as the
input source. If you’ve connected a component video device, select
Component Video. If you’re projecting from a composite
video or S-Video source, make sure the correct selected on the Signal message. See page 56 for details.
Video Signal is
88 Solving Problems
Page 89
Check your computer display settings to correct the color balance.
If the image seems dark, the lamp may be nearing time for
replacement. Check the lamp hours as described on page 62 and replace it, if necessary, as described on page 75.
There is no sound.
Press the button on the remote control or projector to turn up
the volume.
If you’ve turned off the picture and sound, press the A/V Mute
button on the remote control to turn them on again.
If you’re using a VCR or other video source, make sure its volume
is not turned all the way down or muted. Also, make sure the cables are connected correctly, as described in Chapter 1.
Make sure the audio cable is connected to the correct Audio port.
See page 23.
If your presentation includes computer audio, make sure the
volume control on your computer is not turned all the way down or muted. Make sure the audio cable is securely connected to both the projector and your computer’s headphone jack or
audio out jack. See page 23.
The wrong source may be selected. Press the Source Search
button on the projector—or the Comp, S-Video, or Video button on the remote control—to select the correct source.
Solving Problems 89
Page 90

Solving Password Problems

You have forgotten the password.
Write down the request code that appears in the Password Protect
Release screen and contact Epson. See “Where To Get Help” on page 92.
If you turned on the password protect feature before setting the
password and no password was set before, try using the default password:
0000.
The remote control is not available.
You must have the remote control to enter the password. If necessary, you can purchase a replacement remote control from Epson. See page 93 for details about ordering.

Solving Problems with the Remote Control

90 Solving Problems
The projector doesn’t respond to remote control commands.
Make sure you are within 20 feet of the projector, and within
range of the projector’s front or back sensor (approximately 30° to the left or right and 15° above or below).
The remote control batteries may not be installed correctly or may
be low on power. Replace the batteries as described on page 48.
Dim the room lights and turn off any fluorescent lights. Make
sure the projector is not in direct sunlight. Strong lighting, especially fluorescent lights, may affect the projector’s infrared receivers.
Turn off any nearby equipment that emits infrared energy, such
as a radiant room heater.
Page 91
You have lost the remote control.
You need the remote control to access many projector features. If you have lost it, you can order another from Epson. See page 93 for details about ordering.
You can’t control the mouse pointer with the remote control.
Make sure the USB mouse cable is securely connected to both
your computer’s USB port and the projector’s USB port. For details, see page 21.
Your computer must be connected to the Computer
(Component Video)
your mouse pointer with the remote control.
To use the USB mouse connection on a PC, your system must
have a “clean” installation of Windows 98, Windows Me, Windows XP, or Windows 2000. The connection may not work correctly if your system was upgraded from Windows 95.
If you’re running Windows 98 or Me, you may need to install
USB drivers from your Windows CD-ROM. After you install the drivers, restart both the computer and the projector to resynchronize the setup.
port on the projector in order to control
Solving Problems 91
Page 92

Where To Get Help

Epson provides technical assistance through electronic support services 24 hours a day, as listed in the following table.
Service Access
World Wide Web From the Internet, you can reach Epson’s product
support page at http://support.epson.com. After selecting your product, you can access troubleshooting information, download product documentation, and receive technical advice through e-mail.
Presenters Online Access tips, templates, and training for
developing successful presentations at
http://www.presentersonline.com

Telephone Support Services

To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card included in your Start Here kit. This is the fastest way of speaking to a live representative, and it’s free. This service is available 6 Pacific Time, Monday through Friday, for the duration of your warranty period.
AM to 6 PM,
92 Solving Problems
You may also speak with a projector support specialist by dialing one of these numbers:
U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday
through Friday
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday
through Friday
Toll or long distance charges may apply.
Page 93
Before you call, please have the following information ready:
Product name (Epson PowerLite 76c)
Product serial number (located on the bottom of the projector)
Computer or video configuration
Description of the problem
You can purchase video cables, screens, carrying cases, or other accessories from an Epson authorized reseller. Please call 800-GO-EPSON (800-463-7766) for product information and to find the nearest authorized reseller. To purchase online, visit the Epson Store
SM
at www.epsonstore.com (U.S. sales only). In Canada,
please call (800) 463-7766 for dealer referral.
note
To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer referral in Canada).
Solving Problems 93
Page 94
94 Solving Problems
Page 95

Technical Specifications

General

Type of display Poly-silicon TFT active matrix with MLA
Lens F=1.6, 18.4 to 22.12 mm
Resolution 1024 × 768 pixels (XGA)
Color reproduction Full color, 16.77 million colors
Brightness (ANSI) 2000 lumens (High brightness mode)
1500 lumens (Low brightness mode)
Contrast ratio 400:1
Image size 30 to 300 inches (0.8 to 7.6 meters)
A
Projection distance 2.8 to 35.4 feet (0.9 to 10.8 meters)
Projection methods Front, rear, ceiling
Focus adjustment Manual
Zoom adjustment Manual
Internal sound system 1 W monaural
Optical aspect ratio 4:3 (horizontal:vertical)
Zoom ratio 1:1.2
Noise level 36 dB (High brightness mode)
30 dB (Low brightness mode)
Keystone correction angle
± 30° vertical (maximum)
95
Page 96
note
Lamp life results vary depending on environmental conditions and usage. Turn the projector off when not in use. Continuous 24-hour-a-day use may reduce the overall life of the product.

Projection Lamp

Power consumption 170 W UHE
Lamp life About 2000 hours (High brightness);
3000 hours (Low brightness)

Remote Control

Range 20 feet (6 meters)
Batteries (2) Alkaline AAA

Mouse Compatibility

Supports USB

Dimensions

Height 3.4 to 3.9 inches (foot extended)
(86 to 98 mm)
Width 12.9 inches (327 mm)
Depth 9.7 inches (246 mm)
Weight 5.7 lb (2.6 kg)
96 Technical Specifications

Electrical

Rated frequency 50/60 Hz
Power supply 100 to 120 VAC, 2.9 A
200 to 240 VAC, 1.2 A
Power consumption Operating: 250 W
Standby: 4 W
Page 97

Environmental

Temperature Operating: 41 to 95 °F (5 to 35 °C)
Storage: 14 to 140 °F (–10 to 60 °C)
Humidity Operating: 20 to 80% RH,
non-condensing
Storage: 10 to 90% RH, non-condensing
Altitude Up to 4,921 feet (1,500 m)
Up to 7,500 feet (2,286 m) with high altitude mode enabled

Safety and Approvals

United States FCC 47CFR Part15B Class B (DoC)
UL60950 Third Edition
Canada ICES-003 Class B
CSA C22.2 No. 60950 (cUL)
CE Marking Directive 73/23/EEC, 89/336/EEC
IEC60950 Third Edition EN 55022, EN 55024
Pixelworks projector.
DNX™ ICs are used in this
Technical Specifications 97
Page 98

Compatible Video Formats

You can use any of the following video sources: VCR, DVD player, camcorder, digital camera, gaming console, or laser disc player. The projector supports composite video, S-Video, component video, and RGB video, and it automatically senses the video format (HDTV, SDTV, NTSC, PAL, or SECAM).
The projector supports these international video standards:
Mode Refresh Rate (Hz)
NTSC NTSC 4:3 PAL M-PAL N-PAL PAL60 SECAM
TV525i TV625i SDTV480p SDTV480p HDTV720p HDTV720p HDTV1080i HDTV1080i
60 60 50 60 50 60 50
60 50 60 50 60 50 60 50
98 Technical Specifications
Page 99

Compatible Computer Display Formats

You can connect the projector to a wide range of computers, including PCs and notebooks, Apple Macintosh, Power Macintosh series (including G3, G4 and G5 systems), PowerBook computers, many iMac and iBook series systems, and high-end workstations such as the
®
Sun
SPARCstation.
Although images are displayed at the projector’s native resolution of 1024 × 768 pixels, Epson’s patented SizeWise chip supports computer display formats ranging from VGA through UXGA.
To project images output from a computer, the computer’s external monitor signal must be set at a refresh rate (vertical frequency) that’s compatible with the projector; see the following table for compatible formats. For best results, the computer’s resolution should be set to match the projector’s native resolution (1024 × 768). If this resolution isn’t available, select one of the other compatible formats:
Windows:
Right-click the desktop, select and select a compatible resolution. (For a notebook displaying through an external monitor port, you’ll need to click the
Advanced button on the Settings tab, then adjust the resolution
of the external monitor.)
Properties, click the Settings tab,
Macintosh OS X:
From the Apple menu, select
Displays. Make sure the VGA Display or Color LCD dialog box
is selected, then click the
System Preferences, then click
Display tab and select a compatible
resolution.
Macintosh OS 9.x:
On the Apple menu, choose
Monitors or Monitors and Sound. Click the Monitor tab and
Control Panels, then click
select a compatible resolution for your external monitor.
You may need to modify existing presentation files if you created them for a different resolution. See your software documentation for details.
Technical Specifications 99
Page 100
The projector supports these monitor display formats:
Mode Refresh Rate (Hz) Resolution
VGA EGA 70 640 × 350
VGA—60 VESA—72 VESA—75 VESA—85
SVGA—56 SVGA—60 SVGA—72 SVGA—75 SVGA—85
XGA—60 XGA—70 XGA—75 XGA—85
SXGA1—70 SXGA1—75 SXGA1—85
SXGA2—60 SXGA2—75 SXGA2—85
SXGA3—60 SXGA3—75 SXGA3—85
SXGA+60 SXGA+75 SXGA+85
UXGA—60 60 1600 ×
iMAC VGA iMAC SVGA iMAC XGA MAC13 MAC16 MAC19—60 MAC19 MAC21
60 72
75 85
56 60 72 75 85
60 70 75 85
70 75 85
60 75 85
60 75 85
60 75 85
117 95 75 67 75 59 75 75
640 × 480 640 × 480
640 × 480 640 × 480
800 × 600 800 × 600 800 × 600 800 × 600 800 × 600
1024 × 768 1024 × 768 1024 × 768 1024 × 768
1152 × 864 1152 × 864 1152 × 864
1280 × 960 1280 × 960 1280 × 960
1280 × 1024 1280 × 1024 1280 × 1024
1400 × 1050 1400 × 1050 1400 × 1050
640 × 480 800 × 600 1024 × 768 640 × 480 832 × 624 1024 × 768 1024 × 768 1152 × 870
1200
100 Technical Specifications
Loading...