SONY 29FS120, 29FA310, 29D4V3X Service Manual

HISTORY INFORMATION FOR THE FOLLOWING MANUAL:

SERVICE MANUAL

MODEL NAME REMOTE COMMANDER DESTINATION CHASSIS NO.

KV-27FS120
KV-27FS120
KV-29FA310
KV-29FA310
KV-29FS120
KV-29FS120

RM-Y195 US SCC-S61N-A

RM-Y195 CANADA SCC-S59J-A

RM-Y180 LATIN NORTH SCC-S60V-A

RM-Y180 LATIN SOUTH SCC-S60W-A

RM-Y195 LATIN NORTH SCC-S73D-A

RM-Y195 LATIN SOUTH SCC-S73E-A

BA-6

CHASSIS

ORIGINAL MANUAL ISSUE DATE: 3/2004

REVISION DATE SUBJECT

3/2004 No revisions or updates are applicable at this time.

TRINITRON® COLOR TELEVISION

9-965-960-01

Self Diagnosis

Supported model

SERVICE MANUAL

MODEL NAME REMOTE COMMANDER DESTINATION CHASSIS NO.

KV-27FS120
KV-27FS120
KV-29FA310
KV-29FA310
KV-29FS120
KV-29FS120

RM-Y195 US SCC-S61N-A

RM-Y195 CANADA SCC-S59J-A

RM-Y180 LATIN NORTH SCC-S60V-A

RM-Y180 LATIN SOUTH SCC-S60W-A

RM-Y195 LATIN NORTH SCC-S73D-A

RM-Y195 LATIN SOUTH SCC-S73E-A

BA-6

CHASSIS

KV-27FS120 KV-29FA310

TRINITRON® COLOR TELEVISION

9-965-960-01

KV-27FS120/29FA310/29FS120

TABLE OF CONTENTS

SECTION TITLE PAG E

Specifi cations ............................................................................................................................................................................. 4

Warnings and Cautions .............................................................................................................................................................. 5

Safety Check-Out ....................................................................................................................................................................... 6

Self-Diagnostic Function............................................................................................................................................................. 7

SECTION 1: DISASSEMBLY............................................................................................................................................................. 9

1-1. Rear Cover Removal (All Except KV-29FA310)................................................................................................................. 9

1-2. Rear Cover Removal (KV-29FA310 Only).......................................................................................................................... 9

1-3. Chassis Assembly Removal (All Except KV-29FA310) .................................................................................................... 10

1-4. Chassis Assembly Removal (KV-29FA310 Only)............................................................................................................. 10

1-5. Service Position (All Except KV-29FA310)........................................................................................................................11

1-6. Service Position (KV-29FA310 Only) ................................................................................................................................11

1-7. Picture Tube Removal...................................................................................................................................................... 12

Anode Cap Removal Procedure....................................................................................................................................... 12

SECTION 2: SET-UP ADJUSTMENTS............................................................................................................................................ 13

2-1. Beam Landing .................................................................................................................................................................. 13

2-2. Convergence.................................................................................................................................................................... 14

2-3. Focus ............................................................................................................................................................................... 15

2-4. Screen (G2)...................................................................................................................................................................... 16

2-5. Method of Setting the Service Adjustment Mode ............................................................................................................. 16

2-6. White Balance Adjustments ............................................................................................................................................. 16

SECTION 3: SAFETY RELATED ADJUSTMENTS......................................................................................................................... 17

3-1.

X

R564 Confi rmation Method (HV Hold-Down Confi rmation) and Readjustments ........................................................ 17

3-2. B+ Voltage Confi rmation and Adjustment ........................................................................................................................ 17

SECTION 4: CIRCUIT ADJUSTMENTS.......................................................................................................................................... 19

4-1. Setting the Service Adjustment Mode .............................................................................................................................. 19

4-2. Memory Write Confi rmation Method ................................................................................................................................ 19

4-3. Remote Adjustment Buttons and Indicators ..................................................................................................................... 19

4-4. Service Data Lists ............................................................................................................................................................ 20

4-4. ID Map Table .................................................................................................................................................................... 32

4-5. A Board Adjustments........................................................................................................................................................ 32

SECTION 5: DIAGRAMS................................................................................................................................................................. 35

5-1. Circuit Boards Location .................................................................................................................................................... 35

5-2. Printed Wiring Board and Schematic Diagram Information.............................................................................................. 35

5.3. Block Diagram and Schematics ....................................................................................................................................... 36

A Board Schematic Diagram ........................................................................................................................................... 37

CW Board Schematic Diagram ....................................................................................................................................... 39

D Board Schematic Diagram (All Except KV-29FA310) .................................................................................................. 40

HS Board Schematic Diagram (All Except KV-29FA310)................................................................................................. 41

V Board Schematic Diagram ........................................................................................................................................... 41

GD Board Schematic Diagram (KV-29FA310 Only) ......................................................................................................... 44

HR Board Schematic Diagram (KV-29FA310 Only) ......................................................................................................... 47

HU Board Schematic Diagram (KV-29FA310 Only) ......................................................................................................... 49

K Board Schematic Diagram (KV-29FA310 Only) ........................................................................................................... 52

5-4. Semiconductors ............................................................................................................................................................... 53

SECTION 6: EXPLODED VIEWS.................................................................................................................................................... 54

6-1. Picture Tube (KV-27FS120/29FS120 Only) ..................................................................................................................... 54

6-2. Chassis (KV-27FS120/29FS120 Only)............................................................................................................................. 55

6-3. Picture Tube (KV-29FA310 Only)..................................................................................................................................... 56

6-4. Chassis (KV-29FA310 Only) ............................................................................................................................................ 57

SECTION 7: ELECTRICAL PARTS LIST....................................................................................................................................... 58

KV-27FS120/29FA310/29FS120

3

SPECIFICATIONS

)

r

KV-27FS120/29FA310/29FS120

KV-27FS120

Power Requirements 220V, 50/60Hz 120V, 60Hz 220V, 50/60Hz

120V, 60Hz

KV-29FS120

(L. NORTH)

KV-29FS120

(L. SOUTH)

KV-29FA320

(L. NORTH)

KV-29FA320

(L. SOUTH)

Number of Inputs/Outputs

1)

Video
S Video
Y,PB, P

R

Audio

Speaker Output(W

Subwoofe

2)

3)

4)

3
1
1

2

10W x 2

N/A

3
1
1

2

7W x 3

20W

Power Consumption (W)

In Use (Max) 175W 220W 215W

In Standby (Max)

5)

180W

1W

1W 1W 1W

Dimensions (W x H x D)

mm

in

768 x 589 x 497 mm

30

1/4

x 23

1/4

x 19

5/8

in

784 x 678 x 520.5 mm

7/8

x 26 3/4 x 20

30

1/2

in

Mass

50 kg

110 lbs 4 oz

Television system

American TV standard, NTSC

Channel coverage

VHF: 2-13/ UHF: 14-69/ CATV: 1-125

kg

lbs

45.2 kg

99 lbs 10 oz

1)

1 Vp-p 75 ohms unbalanced, sync negative

2)

Y: 1 Vp-p 75 ohms unbalanced, sync negative

C: 0.286 Vp-p (Burst signal), 75 ohms

3) Y: 1.0 Vp-p, 75 ohms, sync negative; PB: 0.7 Vp-p, 75 ohms;

PR Vp-p, 75 ohms.

4)

500 mVrms (100% modulation), Impedance: 47 kilohms

5)

This specifi cation is the maximum wattage.

Picture tube

FD Trinitron® tube

Visible screen size

27-inch picture measured diagonally

Actual screen size

29-inch measured diagonally

Supplied Accessories

Remote Commander RM-Y195

(All Except KV-29FA310 Only)

Remote Commander RM-Y180

(KV-29FA310 Only)

Two Size AA (R6) Batteries

© 2004 Dolby Laboratories, Inc.
Dolby, Pro Logic, and the double-D symbol are registered
trademarks of Dolby Laboratories.

TruSurround

TruSurround is a trademark of SRS Labs, Inc. SRS and the SRS
symbol are registered trademarks of SRS Labs, Inc. in the United
States and in select foreign countries. SRS and TruSurround are
incorporated under license from SRS Labs, Inc. and are protected
under United States Patent Nos. 4,748,669 and 4,841,572 with
numerous additional issued and pending foreign patents. Pur­chase of this product does not convey the right to sell recordings
made with the TruSurround technology.

by SRS

™

®

SRS (SOUND RETRIEVAL SYSTEM)

The SRS (SOUND RETRIEVAL SYSTEM) is manufactured
by Sony Corporation under license from SRS Labs, Inc. It is
covered by U.S. Patent No. 4,748,669. Other U.S. and foreign
patents pending.

The word ‘SRS’ and the SRS symbol are registered trade­marks of SRS Labs, Inc. BBE and BBE symbol are trademarks of
BBE Sound, Inc. and are licensed by BBE Sound, Inc. under U.S.
Patent No. 4,638,258 and 4,482,866.

KV-27FS120/29FA310/29FS120

Design and specifi cations are subject to change without notice.

4

KV-27FS120/29FA310/29FS120

WARNINGS AND CAUTIONS

CAUTION

Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield, or carbon painted on the CRT, after
removing the anode.

WARNING!!

An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis. The chassis of
this receiver is directly connected to the AC power line.

! SAFETY-RELATED COMPONENT WARNING!!

Components identifi ed by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe
operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements
published by Sony. Circuit adjustments that are critical for safe operation are identifi ed in this manual. Follow these procedures
whenever critical components are replaced or improper operation is suspected.

ATTENTION!!

Apres avoir deconnecte le cap de l’anode, court-circuiter l’anode du tube cathodique et celui de l’anode du cap au chassis metallique
de l’appareil, ou la couche de carbone peinte sur le tube cathodique ou au blindage du tube cathodique.

Afi n d’eviter tout risque d’electrocution provenant d’un chássis sous tension, un transformateur d’isolement doit etre utilisé lors de tout
dépannage. Le chássis de ce récepteur est directement raccordé à l’alimentation du secteur.

! ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!

Les composants identifi es par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces
sont d’une importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero
de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance
est critique pour la securite du fonctionnement sont identifi es dans le present manuel. Suivre ces procedures lors de chaque
remplacement de composants critiques, ou lorsqu’un mauvais fonctionnement suspecte.

KV-27FS120/29FA310/29FS120

5

SAFETY CHECK-OUT

KV-27FS120/29FA310/29FS120

After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:

1. Check the area of your repair for unsoldered or poorly soldered
connections. Check the entire board surface for solder splashes and
bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or
touching high-wattage resistors.

3. Check that all control knobs, shields, covers, ground straps, and
mounting hardware have been replaced. Be absolutely certain that
you have replaced all the insulators.

4. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.

5. Look for parts which, though functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.

6. Check the line cords for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.

7. Check the B+ and HV to see if they are specifi ed values. Make sure
your instruments are accurate; be suspicious of your HV meter if sets
always have low HV.

8. Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.

Leakage Test

The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instructions.

2. A battery-operated AC milliampmeter. The Data Precision 245
digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of
passive VOMs that are suitable. Nearly all battery-operated digital
multimeters that have a 2 VAC range are suitable (see Figure A).

How to Find a Good Earth Ground

A cold-water pipe is a guaranteed earth ground; the cover-plate
retaining screw on most AC outlet boxes is also at earth ground. If the
retaining screw is to be used as your earth ground, verify that it is at
ground by measuring the resistance between it and a cold-water pipe
with an ohmmeter. The reading should be zero ohms.

If a cold-water pipe is not accessible, connect a 60- to 100-watt
trouble- light (not a neon lamp) between the hot side of the receptacle
and the retaining screw. Try both slots, if necessary, to locate the hot
side on the line; the lamp should light at normal brilliance if the screw
is at ground potential (see Figure B).

To Exposed Metal

Parts on Set

0.15 F

Earth Ground

Figure A. Using an AC voltmeter to check AC leakage. Figure B. Checking for earth ground.

KV-27FS120/29FA310/29FS120

1.5 K Ω

AC

Voltmeter

(0.75 V)

Trouble Light

AC Outlet Box

Ohmmeter

Cold-water Pipe

6

KV-27FS120/29FA310/29FS120

SELF-DIAGNOSTIC FUNCTION

Self Diagnosis

Supported model

The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER LED will automatically begin to fl ash. The number
of times the LED fl ashes translates to a probable source of the problem. A defi nition of the STANDBY/TIMER LED fl ash indicators is listed in the
instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the Remote Commander can be used to review
the failure occurrence data stored in memory to reveal past problems and how often these problems occur.

Diagnostic Test Indicators

When an error occurs, the STANDBY/TIMER LED will fl ash a set number of times to indicate the possible cause of the problem. If there is more than
one error, the LED will identify the fi rst of the problem areas.
Results for all of the following diagnostic items are displayed on screen. No error has occurred if the screen displays a “0”.

Diagnostic Item

Description

Power does not turn on

+B overcurrent (OCP)*

I-Prot

IK (AKB)

STANDBY/ TIMER

No. of times

lamp fl ashes

Does not light

2 times

4 times

5 times

Self-Diagnositc

Display/

Diagnostic Result

2:0 or 2:1

4:0 or 4:1

5:0 or 5:1

Probable Cause Location

• Power cord is not plugged in.

• Fuse is burned out (F601). (A Board)

• H.OUT (Q505) is shorted. (A Board)

• IC2751 is shorted. (CW Board)

• +13V is not supplied. (A Board)

• IC545 is faulty. (A Board)

• IC001 is faulty. (A Board)

• Screen (G2) is improperly adjusted.**

Detected Symptoms

• Power does not come on.

• No power is supplied to the TV.

• AC Power supply is faulty.

• Power does not come on.

• Load on power line is shorted.

• Has entered standby state after horizontal raster.

• Vertical defl ection pulse is stopped.

• Power line is shorted or power supply is stopped.

• No raster is generated.

• CRT Cathode current detection reference pulse
output is small.

*If a +B overcurrent is detected, stoppage of the vertical defl ection is detected simultaneously. The symptom that is diagnosed fi rst by the
mircrocontroller is displayed on the screen.
**Refer to Screen (G2) Adjustments in Section 2-4. of this manual.

Display of Standby/Timer LED Flash Count

2 times

4 times

5 times

LED ON 0.3 sec.

LED OFF 0.3 sec.

LED OFF

3 sec.

Standby/Timer LED

Diagnostic Item Flash Count*

+B Overcurrent 2 times
I-Prot 4 times
IK (AKB) 5 times
*One fl ash count is not used for self-diagnostic.

Stopping the Standby/Timer LED Flash

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER LAMP from fl ashing.

KV-27FS120/29FA310/29FS120

7

KV-27FS120/29FA310/29FS120

Self-Diagnostic Screen Display

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confi rmed, it is possible to bring up past
occurrences of failure on the screen for confi rmation.

To Bring Up Screen Test

In standby mode, press buttons on the Remote Commander sequentially, in rapid succession, as shown below:

Display

Self-Diagnostic Screen Display

Handling of Self-Diagnostic Screen Display

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you
have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.

Clearing the Result Display

To clear the result display to “0”, press buttons on the Remote Commander sequentially when the diagnostic screen is displayed, as shown below:

Channel

Quitting the Self-Diagnostic Screen

To quit the entire self-diagnostic screen, turn off the power switch on the Remote Commander or the main unit.

Channel

SELF DIAGNOSTIC

2: +B OCP 0

3: +B OVP N/A

4: VSTOP 0

5: AKB 1

101: WDT N/A

8

ENTER

5

Sound Volume

Numeral “0” means that no fault was detected.

Numeral “1” means a fault was detected one time only.

-

Power ON

Note that this differs from entering the Service Mode (Sound Volume

+

).

Self-Diagnostic Circuit

FROM

CW BOARD

IC2751 PIN 5

A BOARD

IC001

Y/CHROMA JUNGLE

51

IK-AKBIN

A BOARD

IC545

V. OUT

REF

3

A BOARD

IC001

SYSTEM

IO-BDAT

78

I-Prot

53

A BOARD

IC002

MEMORY

5

BDA

FROM

72

A BOARD

IC561
PIN 7

+B overcurrent (OCP)

Occurs when an overcurrent on the +B (135V) line is detected by pin 72 of IC001 (A Board). If the voltage of pin 72 of IC001 (A Board) is less than 1V
when V.SYNC is more than seven verticals in a period, the unit will automatically turn off.

I-Prot

Occurs when an absence of the vertical defl ection pulse is detected by pin 78 of IC001 (A Board). Power supply will shut down when waveform interval
exceeds 2 seconds.

IK (AKB)

If the RGB levels* do not balance within 2 seconds after the power is turned on, this error will be detected by IC001 (A Board). TV will stay on, but
there will be no picture.

I-HLDWN

O-LED

79

DISPLAY

*(Refers to the RGB levels of the AKB detection Ref pulse that detects 1K).

KV-27FS120/29FA310/29FS120

8

SECTION 1: DISASSEMBLY

1-1. REAR COVER REMOVAL (ALL EXCEPT KV-29FA310)

4

Screws +BVTP 4X16 TYPE2 TT(B)

Rear Cover

2

Screws +BVTP 4X16 TYPE2 TT(B)

KV-27FS120/29FA310/29FS120

2

Screws +BVTP 4X16 TYPE2 TT(B)

5

Screws +BVTP 3X12 TYPE2 TT(B)

1-2. REAR COVER REMOVAL (KV-29FA310 ONLY)

3

Screws +BVTP 4X16 TYPE2 IT3

Rear Cover

3

Screws +BVTP 4X16 TYPE2 IT3

2

Screws +BVTP 4X16 TYPE2 TT(B)

3

Screws +BVTP 4X16 TYPE2 IT3

KV-27FS120/29FA310/29FS120

5

Screws +BVTP 3X10 TYPE2 IT3

6

Screws +BVTP 4X16 TYPE2 IT3

9

1-3. CHASSIS ASSEMBLY REMOVAL (ALL EXCEPT KV-29FA310)

KV-27FS120/29FA310/29FS120

Claw

1-4. CHASSIS ASSEMBLY REMOVAL (KV-29FA310 ONLY)

Chassis Assembly

KV-27FS120/29FA310/29FS120

Claw

Chassis Assembly

10

1-5. SERVICE POSITION (ALL EXCEPT KV-29FA310)

1

Press on catch tab to release A Board.

2

Disconnect cables as needed to allow A Board to be removed.

KV-27FS120/29FA310/29FS120

V Board

CW Board

HS Board

1-6. SERVICE POSITION (KV-29FA310 ONLY)

1

Press on catch tab to release A Board.

2

Disconnect cables as needed to allow A Board to be removed.

D Board

A Board

CW Board

KV-27FS120/29FA310/29FS120

K Board

HU Board

V Board

GD Board

A Board

11

1-7. PICTURE TUBE REMOVAL

WARNING: BEFORE REMOVING THE ANODE CAP
High voltage remains in the CRT even after the power is disconnected. To avoid electric shock,
discharge CRT before attempting to remove the anode cap. Short between anode and CRT
coated earth ground strap.

1

10

1. Discharge the anode of the CRT and remove the anode cap.

2. Unplug all interconnecting leads from the defl ection yoke, neck

8

7

3

6

2

5

9

4

assembly, degaussing coils and CRT grounding strap.

3. Remove the CW Board from the CRT.

4. Remove the chassis assembly.

5. Loosen the neck assembly fi xing screw and remove.

6. Loosen the defl ection yoke fi xing screw and remove.

7. Place the set with the CRT face down on a cushion and remove
the degaussing coil holders.

8. Remove the degaussing coils.

9. Remove the CRT grounding strap and spring tension devices.

10. Unscrew the four CRT fi xing screws [located on each CRT
corner] and remove the CRT [Take care not to handle the CRT
by the neck].

KV-27FS120/29FA310/29FS120

ANODE CAP REMOVAL PROCEDURE

WARNING: High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to

remove the anode cap. Short between anode and coated earth ground strap of CRT.
NOTE: After removing the anode cap, short circuit the anode of the picture tube and the anode cap to either the metal chassis, CRT shield, or carbon
painted on the CRT.

REMOVAL PROCEDURES

c

b

a

Anode Button

Turn up one side of the rubber cap in
the direction indicated by arrow

a

.

HOW TO HANDLE AN ANODE CAP

1. Do not use sharp objects which may cause damage to the surface of the anode
cap.

2. To avoid damaging the anode cap, do not squeeze the rubber covering too
hard. A material fi tting called a shatter-hook terminal is built into the rubber.

3. Do not force turn the foot of the rubber cover. This may cause the shatter-hook
terminal to protrude and damage the rubber.

Use your thumb to pull the rubber
cap fi rmly in the direction indicated
by arrow

.

b

When one side of the rubber cap separates from
the anode button, the anode cap can be removed
by turning the rubber cap and pulling it in the
direction of arrow

.

c

KV-27FS120/29FA310/29FS120

12

SECTION 2: SET-UP ADJUSTMENTS

KV-27FS120/29FA310/29FS120

The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.

These adjustments should be performed with rated power supply
voltage unless otherwise noted.

Set the controls as follows unless otherwise noted:
VIDEO MODE: Pro
PICTURE CONTROL: Normal
BRIGHTNESS CONTROL: Normal

2-1. BEAM LANDING

Before beginning adjustment procedure:

1. Degauss the entire screen.

2. Feed in the white pattern signal.

Adjustment Procedure

1. Input a raster signal with the pattern generator.

2. Loosen the defl ection yoke mounting screw, and set the purity
control to the center as shown below:

Purity Control

Perform the adjustments in order as follows:

1. Beam Landing

2. Convergence

3. Focus

4. Screen (G2)

5. White Balance

Note Test Equipment Required:

1. Color Bar Pattern Generator

2. Degausser

3. DC Power Supply

4. Digital Multimeter

6. Switch over the raster signal to red and blue and confi rm the
condition.

7. When the position of the defl ection yoke is determined, tighten it with
the defl ection yoke mounting screw.

8. If landing at the corner is not right, adjust by using the disk magnets.

3. Turn the raster signal of the pattern generator to green.

4. Move the defl ection yoke backward, and adjust with the purity control
so that green is in the center and red and blue are even on both
sides.

Blue Red

Green

5. Move the defl ection yoke forward, and adjust so that the entire
screen becomes green.

KV-27FS120/29FA310/29FS120

Purity control

corrects this area.

Disk magnets
or rotatable disk
magnets correct

these areas (a-d).

Deflection yoke positioning

b

d

a

b

cd

corrects these areas.

a

c

13

KV-27FS120/29FA310/29FS120

2-2. CONVERGENCE

Before starting convergence adjustments:

1 Perform FOCUS, VLIN and VSIZE adjustments.

2. Set BRIGHTNESS control to minimum.

3. Feed in dot pattern.

Vertical Static Convergence

1. Adjust V. STAT magnet to converge red, green and blue dots in the
center of the screen.

Center dot

RV2750

R

B

G

H.STAT

R
G
B

Horizontal Static Convergence

If the blue dot does not converge with the red and green dots, perform
the following:

1. Move H STAT VR magnet (a) to correct insuffi cient H.Static
convergence.

H STAT VR

V. STAT

BMC MAGNET

PURITY

V.STAT magnet

2. Tilt the V. STAT magnet and adjust static convergence to open or
close the V. STAT magnet.

When the V. STAT magnet is moved in the direction of arrow a and b,

red, green, and blue dots move as shown below:

1

a

b

2

a

a

b

B
G

R

b

b

B
G

R

a

RGB

b

BGR

3

b

KV-27FS120/29FA310/29FS120

a

a

R

G

b

b

B

G

B

R

14

Dynamic Convergence Adjustment

Before performing this adjustment, perform Horizontal and Vertical Static
Convergence Adjustment.

1. Slightly loosen defl ection yoke screw.

2. Remove defl ection yoke spacers.

3. Move the defl ection yoke for best convergence as
shown below:

G

B

R

R

G

B

BGR

B

G

R

R

B

G

R

B

G

KV-27FS120/29FA310/29FS120

B R R B
(R)(B) (B)(R)

4. Adjust XCV core to balance X axis.

5. Adjust YCH VR to balance Y axis.

6. Adjust vertical red and blue convergence with V.TILT (TLV VR.)

Note: Perform adjustment 3-6 while tracking items 1 and 2.

TLH+
TLH-

Screen-Corner Convergence

BGR

B

G

R

B

G

R

B

R

G

B

R

G

R

GB

4. Tighten the defl ection yoke screw.

5. Install the defl ection yoke spacers.

TLH Plate Adjustment

1. Input crosshatch pattern.

2. Adjust PICTURE QUALITY to standard, PICTURE and BRIGHTNESS
to 50%, and OTHER to standard.

3 Adjust the Horizontal Convergence of red and blue dots by tilting the

TLH plate on the defl ection yoke.

RV2750
V.STAT

TLH Plate

1. Affi x a permalloy assembly corresponding to the misconverged areas:

b

a

ba

a-d: screen-corner

misconvergence

c

d

c

d

2-3. FOCUS

1. Adjust FOCUS control for best pictures.

Focus (FV)

Screen (G2)

CW
Board

KV-27FS120/29FA310/29FS120

XCV

(TLV)

YCH

TLV

15

2-4. SCREEN (G2)

1. Input a dot pattern.

2. Set the PICTURE and BRIGHTNESS controls at minimum and
COLOR control at normal.

3. Adjust SBRT, GCUT, BCUT in service mode with an oscilloscope as
shown below so that voltages on the red, green, and blue cathodes
are 160 ± 2VDC.

±

160 – 2VDC

Pedestal

Ground

4. Observe the screen and adjust SCREEN (G2) VR in FBT to obtain
the faintly visible background of dot signal.

2-5. METHOD OF SETTING THE SERVICE

ADJUSTMENT MODE

Service Mode Procedure

KV-27FS120/29FA310/29FS120

2-6. WHITE BALANCE ADJUSTMENTS

1. Input an entire white signal with burst.

2. Set to Service Adjustment Mode.

3. Set the PICTURE and BRIGHTNESS to minimum.

4. Adjust with SBRT if necessary.

ENTER

1

and 4 .

1

4

and

.

to save into the memory.

5. Select GCUT and BCUT with
3

6. Adjust with

6

and

for the best white balance.

7. Set the PICTURE and BRIGHTNESS to maximum.

8. Select GDRV and BDRV with

9. Adjust with

10. Press

3

and 6 for the best white balance.

MUTING

then

1. Standby mode (power off).

2. Press

Display

Channel

Sound Volume

5

Power

+

on the Remote Commander (press each button within a second).

Service Adjustment Mode On

1. The CRT displays the time being adjusted.

2. Press

3. Press

4. Press

Display

hsiz 16

to save into the memory.

service

ntsc

vchp

then

Category

defl

00000000

ENTER

Mode

Signal
Type

1

or 4 on the Remote Commander to select the time.

3

or 6 on the Remote Commander to change the data.

MUTING

Item

00000000

Display

Item

Service Adjustment Mode Memory

Turn the set off then on to exit Service Adjustment Mode.

Mode

Category

Display

Item

Item
Data

service defl hsiz 16

Signal
Type

ntsc

vchp 00000000 00000000

KV-27FS120/29FA310/29FS120

write

MUTING

ENTER

Green

Red

16

SECTION 3: SAFETY RELATED ADJUSTMENTS

KV-27FS120/29FA310/29FS120

3-1. X R564 CONFIRMATION METHOD

(HV HOLD-DOWN CONFIRMATION) AND
READJUSTMENTS

The following adjustments should always be performed when replacing
the following components which are marked with
diagram:

Part Replaced (Y ) Adjustment (X)

DY, T585, CRT, IC001, IC561,
IC600, IC604, C506, C507,
C508, C510, C511, C513,
C514, L588, D566, D567,
D568, PH602, R526, R564,
R565, R566, R851, T510,

T511……....A Board

HV HOLD-DOWN
R564

Y

on the schematic

Preparation Before Confi rmation

1. Using a Variac, apply AC input voltage: 120 ± 2 VAC.

2. Turn the POWER switch ON.

3. Input a white signal and set the PICTURE and BRIGHTNESS
controls to maximum.

4. Confi rm that the voltage between C566 (+) or TP30 and ground is
more than 99VDC.

Hold-Down Readjustment

If the setting indicated in Step 2 of Hold-Down Operation Confi rmation
cannot be met, readjustment should be performed by altering the
resistance value of R564 component marked with

X

.

T585

FBT

ammeter

3.0 mA DC
range

ABL

+

-

A

IABL

3-2. B+ VOLTAGE CONFIRMATION AND

ADJUSTMENT

Note: The following adjustments should always be performed when
replacing the following components, which are marked with
schematic diagram on the A Board:

A BOARD: Y IC604, PH602

Y

on the

Hold-Down Operation Confi rmation

1. Connect the current meter between Pin 11 of the FBT (T585) and the
PWB land where Pin 11 would normally attach (See Figure 1 on the
next page).

2. Input a dot signal and adjust the ABL current to follow with the
PICTURE and BRIGHTNESS control: IABL = 140 ± 100µA.

3. Confi rm the voltage of A Board TP-23 is 135.6 ± 1.0VDC.

4. Connect the digital voltmeter and the DC power supply via Diode
1SS119 to C566 (+) and ground (See Figure 1 on next page).

5. Increase the DC power voltage gradually until the picture blanks out.

6. Turn DC power source off immediately.

7. Read the digital voltmeter indication
(Standard

8. Input 100 IRE White Signal and adjust the ABL current to follow with
the PICTURE and BRIGHTNESS control: IABL = 1820µA ± 200µA.

9. Repeat steps 4 through 7.

114.6 +OVDC/-0.3DC).

1. Using a Variac, apply AC input voltage: 130 + 2.0 / - 0.0 VAC.

2. Input a DOT pattern at Q.C.

3. Set the PICTURE and the BRIGHTNESS controls to minimum.

4. Confi rm the voltage of A Board between TP-23 & Ground is =135.6
± 1VDC.

5. If step 4 is not satisfi ed, replace the components listed above, then
repeat steps 1 throught 3.

KV-27FS120/29FA310/29FS120

17

(

)

FIGURE 1

KV-27FS120/29FA310/29FS120

DIGITAL
MULTIMETER

+

-

X

R564

R

5

3

1

0

4

S

P

R

5

1

1

J

R

1

R

4

3

7

0

6

R

C

4

5

1

C

5

D

5

6

5

2

R

5

8

9

T

2

P

4

2

9

L

3

7

0

1

5

6

C

1

5

T

2

8

6

2

R

5

3

2

L

3

7

1

1

1

5

C

R

2

1

5

C

1

1

5

L

1

C

5

3

1

5

L

0

2

B

2

P

5

T

R

5

0

4

R

5

3

3

C

5

4

0

5

S

5

6

5

C

I

C

5

3

0

6

2

5

D

5

2

5

L

5

1

0

6

2

5

C

1

5

C

4

1

5

C

2

H

5

Q

B

5

2

5

C

3

L

5

1

5

R

5

3

7

R

5

6

2

2

R

5

5

2

2

E

C

5

2

7

R

5

4

9

R

5

1

5

6

7

C

5

6

1

R

5

4

6

5

4

5

D

6

R

5

4

8

C

5

4

5

R

9

0

R

5

4

0

0

D

2

7

C

R

5

4

7

6

0

1

5

L

R

5

6

C

5

4

8

1

J

R

5

0

POWER
SUPPLY

+

­1SS119

C566

Q

4

0

2

R

4

0

8

R

4

1

1

O

R

.

T

H

P

R

P

T

3

0

6

6

5

D

R

5

2

9

C

5

6

2

C

5

2

9

1

6

5

C

I

C

5

4

4

2

C

5

9

7

1

T

P

V

.

O

U

T

5

4

7

5

4

5

C

I

4

1

C

5

9

5

P

7

T

1

R

9

0

1

5

1

2

C

2

5

2

8

D

5

2

8

D

5

6

1

R

5

8

3

2

8

5

C

P

T

3

3

Q

5

2

1

5

7

5

R

C

5

7

1

R

5

6

8

D

5

6

8

6

7

R

5

7

0

D

5

6

R

R

2

8

5

L

9

5

2

6

R

5

6

5

9

7

4

D

6

3

0

6

0

1

2

0

6

C

6

1

0

0

2

4

TP23

8

9

5

E

R

5

0

R

5

9

3

3

0

5

R

C

5

9

0

1

9

5

R

B

0

9

5

Q

R

5

9

4

T

P

1

3

4

2

6

E

C

C

P

3

T

2

1

6

8

C

6

4

0

4

2

6

D

4

5

0

5

C

H

-

O

Q

5

C

5

0

4

1

6

5

0

5

R

U

T

E

0

5

6

0

5

C

6

0

5

D

3

4

R

5

0

6

C

5

1

T

2

P

2

0

C

4

1

5

R

2

1

5

R

H

D

T

5

0

5

T

H

B

5

8

8

R

8

5

L

T

U

O

­6

0

5

Q

6

G

2

0

0

V

8

N

/

C

V

D

Y

+

P

T

2

1

V

D

Y

-

T

2

P

7

H

D

Y

-

P

T

2

8

H

D

Y

-

H

D

Y

+

T

P

H

D

Y

+

3

1

H

-

O

2

9

1

5

5

N

C

D

R

5

9

8

T

1

P

9

H

E

A

T

E

R

N

D

5

V

U

T

-

1

3

V

G

N

D

G

N

D

G

N

D

5

5

T

+

1

3

V

N

/

C

A

B

L

T

2

P

0

R

5

8

8

F

B

T

1

AMMETER
3mA dc range

A

+

-

KV-27FS120/29FA310/29FS120

18

SECTION 4: CIRCUIT ADJUSTMENTS

Electrical AdjustmenTs by Remote Commander

Use the Remote Commander (RM-Y180, RM-Y195) to perform the circuit adjustments in this section.

Test Equipment Required: 1. Pattern generator 2. Frequency counter 3. Digital multimeter 4. Audio oscillator

KV-27FS120/29FA310/29FS120

4-1. SETTING THE SERVICE ADJUSTMENT

MODE

1. Standby mode (Power off).

2. Press the following buttons on the remote commander within a
second of each other:

Display

Channel

5

Sound Volumne

Power

+

Service Adjustment Mode On

1. The CRT displays the item being adjusted.

Item
Data
41

2. Press

3. Press

4. Press

Signal

Category

Display
Item

1

or 4 on the Remote Commander to select the item.

3

or 6 on the Remote Commander to change the data.

MUTING

DEF NTSC 1 NVM OK

M65582AMF-101FPZ0

then

Type

H SIZE

ENTER

Display

Item #

to write into memory.

Service Adjustment Mode Memory

1. Press

Signal
Type

Category

Mode

service defl hsiz 16

Signal
Type

8

then

Mode

service defl hsiz 16

ntsc

vchp 00000000 00000000

ntsc

vchp 00000000 00000000

ENTER

Category

on the Remote Commander to initialize.

Display

Item

write

Display

Item
Data

Item

Item

Data

write

Carry out Step 1 when adjusting
IDs 0-7 and when replacing and
adjusting IC002

4-2. MEMORY WRITE CONFIRMATION

METHOD

1. After adjustment, pull out the plug from the AC outlet, then replace
the plug in the AC outlet again.

2. Turn the power switch ON and set to Service Mode.

3. Call the adjusted items again to confi rm they were adjusted.

4-3. REMOTE ADJUSTMENT BUTTONS AND

INDICATORS

MUTING

(Enter into
memory)

1

Disp. (Item up)

2

(Device Item Up)

4

Disp. (Item down)

8

(Initialize)

VOLUME (+)

(Service Mode)

RM-Y180

POWER

(Service Mode)

DISPLAY

(Service Mode)

3

Item
(Data up)

6

Item
(Data down)

5

(Device item
down)

ENTER

(Enter into
memory)

0

(Remove from
memory)

2. Press

MUTING

then

ENTER

to write into memory.

3. Turn set off then on to exit Service Adjustment Mode.

KV-27FS120/29FA310/29FS120

19

4-4. SERVICE DATA LISTS

p

K

K

K

K

KV-27FS120/29FA310/29FS120

Service

Group

VERSION Fix 0 VER

DEF

Fix/

No.

Var

VAR
VAR
VAR
VAR 4 VPOS
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR

FIX

FIX 18 HMSK

FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX 29 HOSC
FIX
FIX

Name Description

1HSIZ
2HPOS
3 VSIZ

5VLIN
6SCOR
7 VBOW
8 VANG

9TRAP
10 PAMP
11 UPIN
12 LPIN
13 TROT
14 HBL
15 RBL
16 LBL
17 VBL

19 HDW
20 AFC
21 AFC1
22 AFCW
23 CDMD
24 HSS
25 VSS
26 SLDN
27 SLUP
28 JPSW

30 EHT
31 EHTG

rocessor version information

Micro
H-SIZE ( EW DC : YUV OFFSET )
H POSITION: YUV OFFSET
V RAMP SIZE: YUV OFFSET
V POSITION (RAMP DC) NOT USEFUL: YUV OFFSET
V LINEARITY
S CORRECTION
BOW
ANGLE
EW TRAPESIUM
PARABOLA ( EW PIN )
UPPER CORNER ( UPPER PIN )
LOWER CORNER ( LOWER PIN )
TROT
FBPBLK ( H BLK MODE SELECT )
HBLK R POS ( HBLK REAR TIMING: YUV OFFSET )
HBLK F POS ( HBLK FRONT TIMING: YUV OFFSET )
VBLK POS ( V BLK WIDTH )
Macro OFF ( TOP VEND [ WHEN MACROVISION ] PREVENT
OFF )
IIC_HOUT_DUTY ( H PULSE WIDTH [ 25u/19u ]
H AFC Gain ( AFC GAIN )
H Charge pump ( AFC1 TIME CONSTANT )
AFC1 PULLIN ( AFC1 PULL IN WIDE )
V CD MODE ( V DET WINDOW SW TIMING )
SYNC SLICE LVL(H) ( SYNC SLICE LEVEL [ H sepa ] )
SYNC SLICE LVL(L) ( SYNC SLICE LEVEL [ V sepa ] )
AUTO SLICE DOWN ( AUTO SLICE LEVEL DOWN )
AUTO SLICE UP ( AUTO SLICE LEVEL UP )
VJPSW ( JUMP SW )
H VCO FOR OFFSET ADJUST OFFSET
EHT
EHT GAIN ( EHT MODE )

NTSC

Init

Data

=
47
36
28
37
32
49
31
37
24
49
31
30

109

0
15
41

0

0

1

0

3

0

1

0

3

0

0

0

7

4

1

KV-27FS120/29FA310/29FS120

20

KV-27FS120/29FA310/29FS120

Service

Group

16 : 9

Fix/
Var

VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR

No.

1 VSIZ
2 VPOS
3VLIN
4SCOR
5TRAP
6 PAMP
7UPIN
8LPIN

9 ABLG
10 SCON
11 VPW

V RAMP SIZE
V POSITION ( RAMP DC )
V LINEARITY
S CORRECTION
EW TRAPESIUM
PARABOLA ( EW PIN )
UPPER CORNER ( UPPER PIN )
LOWER CORNER ( LOWER PIN )
ABL GAIN
SUB CONTRAST LEVEL
JUMP PULSE WIDTH

NTSC

Item name & ( Description )Name

Init

Data

48
40
26
24
22
24
31
31
15
13

1

KV-27FS120/29FA310/29FS120

21

KV-27FS120/29FA310/29FS120

Service

Group

VP1

Fix/
Var

VAR
VAR 2 GDRV
VAR 3 BDRV
VAR
VAR 5 GCUT
VAR 6 BCUT
VAR
VAR
VAR
VAR

FIX 11 RON
FIX 12 GON
FIX 13 BON

FIX 14 BLLV

FIX

FIX
VAR 17 SSHO
VAR 18 SSHP
VAR 19 SHPF

FIX 20 SHCL

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX 28 BKAT

FIX 29 BKRC

FIX 30 BKDP

FIX

Name Item name & ( Description )No.

1 RDRV

4 RCUT

7SCON
8 SHUE
9SCOL

10 SBRT

15 MTRX
16 AXIS

21 SHMX
22 ACLV
23 AKBD
24 AKBS
25 REFP
26 YNRC
27 BKON

31 BKSP

R DRIVE
G DRIVE: GDOF OFFSET ( only Color Temp. "Warm")
B DRIVE: BDOF OFFSET ( only Color Temp. "Warm")
HARDWARE AKB (R) CMP DATA
HARDWARE AKB (G) CMP DATA
HARDWARE AKB (B) CMP DATA
SUB CONTRAST LEVEL
SUB TINT (HUE)
SUB COLOR LEVEL
SUB BRIGHTNESS
R OUTPUT ON ( 0:R OUTPUT OFF 1:R OUTPUT ON )
G OUTPUT ON ( 0:R OUTPUT OFF 1:R OUTPUT ON )
B OUTPUT ON ( 0:R OUTPUT OFF 1:R OUTPUT ON )

BLUE STRETCH ( 00:NO<->11:DEEP ) only Color Temp "Cool"
MATRIX RATIO SELECT
R-Y PHASE SELECT
SUB SHARPNESS GAIN (OVER) RF/VIDEO
SUB SHARPNESS GAIN (PRE) RF/VIDEO
SHARPNESS FOR ( 00:2 CLK <-> 11:5 CLK )
SHARPNESS CORING LEVEL
SHARPNESS LIMITER LEVEL
ACL GAIN
AKB SELF DIAGNOSTIC COUNTER (@1 SEC)
AKB SWITCH ( 0:AKB OFF 1:H/W AKB ON )
AKB REFPLS TIMING
YNR LIMITER LEVEL
BLACK STRETCH ON
BLACK STRETCH DETECTOR TIME CONSTANT1
BLACK STRETCH DETECTOR TIME CONSTANT2
BLACK STRETCH DEPTH
BLKSTPNT BLACK STRETCH POINT

NTSC

Init Video YUV 16:09

Data

64
45 45 48 N/A
45 45 44 N/A

120

91 91 90 N/A
87 87 105 N/A
19

777
14 14 24
13 13 15

1

1

1

1

0
52
10 25 25 N/A
15 30 30 N/A

100N/A

0
15

0

2

1

0
15

1
15

4

soft cont'l

2

64 64 N/A

120 120 N/A

19 19 N/A

N/A
N/A
N/A

KV-27FS120/29FA310/29FS120

22

KV-27FS120/29FA310/29FS120

Service

Group

VP2

Fix/

No. Name Item name & ( Description )

Var

FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX

FIX 12 YCMD

FIX 13 VACL
FIX
FIX 15 VAMX
FIX
FIX
FIX
FIX
FIX

FIX
VAR
VAR
VAR
VAR
VAR

FIX

1VMOF
2VMLO
3VMHI
4VMDL
5VMPL
6VMWD
7VMCL
8 VMMX

9CKLV
10 CKON
11 ALFA

14 VAGA

16 GAMM
17 YDLY
18 CDLY
19 YOFF
20 CBPF
21 BGPP
22 GDOF
23 BDOF
24 GCOF
25 BCOF
26 DCTV
27 DCTG

NTSC

Init Video YUV 16:09

Data

VM GAIN(Off) ( VM LEVEL AT "OFF" SETTING ) 2
VM GAIN(Low) ( VM LEVEL AT "LOW" SETTING )
VM GAIN(High) ( VM LEVEL AT "HIGH"SETTING )
VM DELAY ( VM DELAY )
VM POL ( VM POLARITY )
VM WIDTH ( VM WIDTH )
VM CORING LEVEL ( VM CORING LEVEL )
VM MAX ( VM LIMITER LEVEL )
KILLER LEVEL ( VM COLOR KILLER VTH )
FORCE KILLER ( FORCE KILLER )
ALFA ( ADAPTIVE DET SENSITIVITY )
MANEXP ( YC SEPA FORCE SELECT [ 00:ADAPTIVE 01:H 10:V
11:HV ] )
V APERTURE CORING LV ( V APERTURE CORING LEVEL )
V APERTURE GAIN ( V APERTURE GAIN LEVEL )
V APERTURE MAX GAIN (V APERTURE LIMITER LEVEL)
GAMMA ( GAMMA [ 00:NO <-> 11:DEEP ] )
Y DELAY ( Y DELAY TIME )
C DELAY ( C DELAY TIME )
Y Mute ( Y OUTPUT MUTE )
SAW FILTER(7.2MHzBPF) ( C BPF FOR HI )
BGP POS ( BGP [ FOR C DECODER ] TIMING )
G DRIVE OFFSET only Color Temp. "Warm"
B DRIVE OFFSET only Color Temp. "Warm"
G CUT CMP DATA OFFSET only Color Temp. "Warm"
B CUT CMP DATA OFFSET only Color Temp. "Warm"
DCTRAN VTH<6:0> ( DCTRANSFER VTH )
DCTRAN GAIN<4:0> ( DCTRANFER GAIN )

soft cont'l

soft cont'l

soft cont'l

4

7
6
0
0
0

15

1
0
2

0

0

5

1
0
0
0
9

9
14
11
28
30

10N/A

13N/A

928N/A

KV-27FS120/29FA310/29FS120

23

KV-27FS120/29FA310/29FS120

Service

Group

Service

Group

PALLET NR

Fix/

No. Name

Var

VAR
VAR
VAR

FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX

Fix/
Var

FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX 11 VBKP
FIX 12 TBKD

1SCOL
2 SHCL
3SHMX
4 YNRC
5VMHI
6VMCL
7 VMMX
8 VAMX

9GAMM
10 YNRS
11 WSTH
12 WSVA
13 WSCA
14 NRCH
15 NRCL
16 NRVL
17 NRVH
18 IPNC
19 IPNV

No.

Name

1 VPIC

2 VBRI

3VCOL

4 VHUE

5 VSHA

6 VVM

7VTRI

8 VAPA

9VGMA
10 VDCT

NTSC

Item name & ( Description )

SUB COLOR LEVEL 14
SHARPNESS CORING LEVEL
SHARPNESS LIMITER LEVEL
YNR LIMITER LEVEL
VM LEVEL AT " HIGH " SETTING
VM CORING LEVEL
VM LIMITER LEVEL
V APERTURE LIMITER LEVEL
GAMMA ( 00: NO < - > 11:DEEP)
YNR ON
WEAK SIGNAL VTH
WEAK SIGNAL VIDEO ATT
WEAK SIGNAL CHROMA ATT
THRNZV1( NOISE DET TIME CONSTANT )
THRNZV2 ( NOISE DET TIME CONSTANT )
THRNZH1 ( NOISE DET VTH )
THRNZH2 ( NOISE DET VTH )
DETNZ STATUS COUNTER
DETECTION PERIOD

Item name & ( Description )

PICTURE
BRIGHTNESS
COLOR
HUE
SHARPNESS
VM
COLOR TEMP
APERTURE G
GAMMA
DCT LV
BLACK STRETCH DEPTH ( VIDEO )
BLACK STRETCH DEPTH ( TUNER )

Init

Data

15

10

16

10

PALLET

= VIVID

63 50 37 31
27 30 31 31
37 32 31 31
31 31 31 31
31 32 31 21

23 15 2 2

7
7

0
7
0
0
1
7
0
5
0

2
0
2

NTSC

BA6 DATA (DEC)

PALLET

= STD

2100
0121
5530
3100

3347
3347

PALLET

= MOVIE

PALLET

= PRO

KV-27FS120/29FA310/29FS120

24

KV-27FS120/29FA310/29FS120

(

)

(

)

(

)

(

y

]

(

)

(

)

(

)

(

)

(

])

(

)

Service

Group

Y

Service

Group

C

Fix/
Var

No.

Name

FIX 1 YNRS
FIX 2 YTHR
FIX 3 Y2D
FIX 4 2DFX

FIX 5 CLPS

FIX 6 VLPF
FIX 7 CLPF
FIX 8 BPFB
FIX 9 BPFF
FIX 10 BKTS

FIX 11

VMG

2

FIX 12 CLPT

Fix/

No.

Var

FIX 1
FIX 2
FIX 3

Name Item name & ( Description )

A1FL

A1ON

ACCS
FIX 4 AASL
FIX 5
FIX 6
FIX 7
FIX 8
FIX 9
FIX 10
FIX 11
FIX 12
FIX 13
FIX 14
FIX 15

BASL
XFFR
A2ON
A3ON

A2FL

A3FL
AXTH
ACTH
AVAV
B2TH

ACCP

Item name & ( Description )

YNR SW
Y THR 2D
Y2D Fix
C BPF Fix

YNR ON

Y SIGNAL THROUGH 2DYCS

Y SIGNAL GENERATE from 2DYCS

C SIGNAL GENERATE from H/V BPF onl
CLAMP CONTROL SW ( 0: CLAMP OFF. 1:
CLAMP AUTO. 2: CLAMP ON
VIDEO LPF
CHROMA LPF
YCS HBPF BACK
YCS HBPF FRONT
BS T2 IFON

Y_LPF [ ANALOG ] for adjust

C_LPF [ ANALOG ] for adjust

YCS HBPF SELECT [ BACK ]

YCS HBPF SELECT [ FRONT ]

BLACK STRETCH RECOVER TIME OUT

VMGAIN2 ( MODULATOR FEEDBACK GAIN CONTROL
CLAMP KEEP TIMER ( CLAMP AUTO ON KEEP TIMER COUNT [

@ 100 MS

AMP OFF1 L ( ANALOG ACC hysteresis )
AMP ON ( ANALOG ACC AMP ON LEVEL)
ACC SW ( ACC ON/OFF )
AVE SEL

C DECODER TIME CONSTANT [32, 16, 8, 1H ]
B2AVE SEL ( ACC TIME CONSTANT )
FREE RUN ( VCXO FORCE FREERUN )
AMP2 ON Thresh ( ABL VTH )
AMP3 ON Thresh ( ACL VTH )
AMP2 OFF Thresh L ( AMP2 OFF LEVEL LOWER )
AMP3 OFF Thresh L ( AMP3 OFF LEVEL LOWER )
AXIS HYS ( AXS HYS )
ROM HYS ( ROM HYS )
AVE SEL AV (AVE SEL AV )
B2COMP ( B2COMP )
ACC COMP ( ACC COMP )

NTSC

Init

Data

0
0
0
1

1

3
3
1
1
0

3

15

A8
Init Video YUV 16:09

Data

90

4
0

01N/A
2
0
0

01N/A
4
4

64
64
30
10

3
0
0

KV-27FS120/29FA310/29FS120

25

KV-27FS120/29FA310/29FS120

(

)

Service

Group

RGB

Fix/

No. Name

Var

FIX
FIX
FIX
FIX

FIX 5 COGL

FIX 6 COGH

FIX 7 COBL

FIX 8 COBH

FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX 20 UOFS
FIX
FIX
FIX
FIX
FIX

1AMUT
2PMUT
3CORL
4CORH

9 ABLS
10 ALSP
11 ALRS
12 ALAS
13 ABLG
14 ALS2
15 AKBM
16 AKBP
17 OSDL
18 UVIN
19 UVG

21 VOFS
22 AALG
23 AALS
24 UVDE
25 UVDT

Item name & ( Description )

RGB POWER ON MUTE ( RGB POWER ON MUTE )
RGB Mute before OSD ( RGB MUTE [ EXCEPT OSD ]
CUTOFF R L ( R CUTOFF LOWER )
CUTOFF R H ( R CUTOFF UPPER )
CUTOFF G L ( G CUTOFF LOWER WHEN TEMP IS "COOL" AND
"NEUTRAL"
CUTOFF G H ( G CUTOFF LOWER WHEN TEMP IS "COOL" AND
"NEUTRAL"
CUTOFF B L ( B CUT OFF LOWER WHEN TEMP IS "COOL" AND
"NEUTRAL"
CUTOFF B H ( B CUT OFF LOWER WHEN TEMP IS "COOL" AND
"NEUTRAL"
ABL SEL ( ABL SELECT )
ACL SPEED ( ACL SPEED )
ACL SPE ( ACL RECOVER SPEED )
ACL ASPE ( ACL ATACK SPEED )
ABL GAIN ( ABL GAIN )
ACLASPE2 ( ACL ATACK SPEED [ 2 ] )
AKB MODE ( AKB MODE )
AKB P[5:0] ( AKB PULSE HEIGHT )
OSD LIMIT ( OSD LIMMIT SELECT )
Y/U/V UVINV ( U/V INVERT )
U/V GAIN ( U/V OFFSET CANCELER ON )
U IN OFFSET
V IN OFFSET ( V IN OFFSET )
ANA ACL GAIN ( ANALOG ACL GAIN CONTROL )
ANA ACL ON ( ANALOG ACL ON/OFF CONTROL)
UV_DITHER_EN ( UVIN DITHER ENABLE )
UV_DITHER_TEST ( UVIN DITHER TEST )

U IN OFF SET

NTSC

Init Video YUV 16:09

Data

0
1

212

0

197

0

176

0

0
0
2
9
5
2
0

16

0
0

0
15
12

0

1

0

0

01N/A
06N/A

KV-27FS120/29FA310/29FS120

26

KV-27FS120/29FA310/29FS120

K

K

Service

Group

DEFD

Fix/

No.

Var

FIX
FIX
FIX

FIX 4 EWCL V/EW DAC CLK CONTROL ( EW/VRAMP DA CLOCK SELECT ) 0 0 0 N/A

FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX

1 HFFR
2HFUP
3JSWW

5XF0A
6BGST
7 XPHA
8 HRMP

9RPLU
10 RPLB
11 XF0B
12 RPLS
13 SSM
14 VSAG
15 AFC2
16 VRFL
17 SSLP
18 XPLU
19 8FSC
20 4FS2
21 CDM2
22 BGPC
23 MHDL
24 BFRE

AFC FREE RUN ( AFC1 FORCE FREE RUN )
HFREE UP ( H FREE RUN FREQUENCY UP [ 700 Hz ]
VJP WIDTH ( JUMP PULSE WIDTH )

FREE RUN OFFSET ( VCXO FREE RUN ADJUST)
BG START ( BGP [ FOR PLL ] TIMING )
VCXO CTL ( VXCO PHASE ADJUST )
Ramp Slew Rate ( AFC2 TIME CONSTANT )
Ref Charge pump ( REF PLL TIME CONSTANT )
Ref VCO ( REF PLL TIME CONSTANT )
VCXO FREE RUN ( VXCO Fo ADJUST )
REF FB SW ( REF VCO FB LOOP SELECT )
Sync Sepa Mask ( SyncSepaMasking CONTROL )
V-sag ( V-SAG prevent ON )
AFC2 Gain ( AFC2 GAIN CONTROL )
V RAMP FIL OFF ( V RAMP FILTER SWITCHING OFF )
LPY SYNC ( LFP pre SYNC SEPA ON/OFF
B PLL Change pump ( ACP TIME CONSTANT )
8FSC SEL ( 8fsCLK Skew OFF )
4FSC SEL2 ( 4fsCLK Skew OFF )
V_CD_MODE2 ( V_LOGIC SW )
Add. FTN BGP C ( BGP C )
Add. FTN BGP SEL ( BBP SEL )
V FREE ( FORCE V FREE RUN )

Item name & ( Description )Name

NTSC

Init Video YUV 16:09

Data

0
0
0

0
16
10

3

3

1

0

0

0

0

3

1

1

1

1

1

1

0

1

0

16 1 N/A

10N/A
10N/A

FIX 25 HRPP AFC2 RAMP POS ( FRAMP RRAMP H OUT CONTROL RANGE 8

FIX
FIX
FIX

FIX 29 DTH

FIX

26 DSC
27 VBH
28 VPW

30 SLON

CLOCK SEL ( DS DAC CLK SW 2 )
VBLK HALFKIL ( V BLK HALF KILL )
V PLS WIDTH ( V Pulse Wide )
D THRESHOLD LEVEL ( DITHER THRESHOLD LEVEL
CONTROL AT IIC AUTOD= ON
LPF SYNC ON ( LPF SYNC ON )

KV-27FS120/29FA310/29FS120

1

0

1

0

1

110

27

KV-27FS120/29FA310/29FS120

Service

Group

Service

Group

Fix/

No.

Var

FIX 31 VSSW

FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX

Fix/

No.

Var

FIX 1 PCLP

FIX 2 VRT

FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX

Name Item name & ( Description )

32 AF2S
33 VSL2
34 VSL1
35 VYUV
36 VYVP
37 VYHS
38 VYHP
39 VSHE
40 VYRB
41 VYLB

Name

3 14HI
4 14HD
5DSI
6DSD
7 ADCD
84FSC

9WSTH
10 WSVA
11 WSCA
12 VREF

NTSC

SYNC SLICE LVL(V)_W ( SYNC SLICE LEVEL [ V ] Wide Window
AFC2_SEL ( ADC2 TIMING SW )
V_SYNC_LPF_2 ( DIGITAL V_SINC_LPF [ Fall ] )
V_SYNC_LPF_1 ( DIGITAL V_SINC_LPF [ Rise ] )
YUV VSIZE OFFSET ( YUV V-SIZE OFFSET )
YUV VPOS OFFSET ( YUV V-POSITION OFFSET )
YUV HSIZE OFFSET ( YUV H-SIZE OFFSET )
YUV HPOS OFFSET ( YUV H-POSITION OFFSET)
V-SHRINK MODE ( V-SHRINK MODE for AV )
YUV RBLK ( YUV RBLK OFFSET )
YUV LBLK ( YUV LBLK OFFSET )

NTSC

Item name & ( Description )

pedestal CLAMP ON/OFF ( SYNC TIP/PEDESTAL CLAMP
SELECT )
VRT Voltage ( ADC REFERENCE [ 00:1.15Vpp 01:1.25 Vpp
10:1.35 Vpp 11:1.45 Vpp ] )
INV 14H CLK ( 4fsc [ Skew ] CLK POLARITY )
14H CLK DLY ( 4fscCLK [ Skew ] CLK DELAY ADJUST )
INV DS CLK ( 8fscCLK POLARITY )
DS CLK DLY ( 8fscCLK DELAY ADJUST )
AD CLK DLY ( ADC CLK DELAY ADJUSTO )
4FSC SW ( AD/LOGIC CLK SWAP )
WEAK_SIG_VTH ( WEAK_SIGNAL VTH )
WEAK SIG VIDEO ATT ( WEAK SIGNAL VIDEO ATT )
WEAK SIG CHROMA ATT (WEAK SIGNAL CHROMA ATT)
VREF_SEL ( AD REFERENCE SELECT [ VZ ] )

Init Video YUV 16:09

Data

0

0
0
1
8
8
8
7
0
7
7

Init Video YUV 16:09

Data

0

1

0
0
0
0
0
0
0
0
0
0

00N/A
00N/A
00N/A
00N/A
01N/A

00N/A
00N/A

Service

Group

OSD OTHER DEFD

Fix/
Var

FIX 1
FIX 2
FIX
FIX
FIX

KV-27FS120/29FA310/29FS120

NameNo.

HT ( HALF TONE LEVEL )

HT

OSLR
3OSLG
4OSDC
5OSLB

OSD LVL R ( R OSD LEVEL )
OSD LVL G ( G OSD LEVEL )
OSD COMP ( OSD COMP )
OSD LVL B ( B OSD LEVEL )

Item name & ( Description )

NTSC

Init

Data

0
25
25

0
25

28

KV-27FS120/29FA310/29FS120

(

)

(

)

Service

Group

H/W AKB

Fix/
Var

FIX
FIX

FIX 3 HGIL

FIX 4 HGIH

FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX 13 HASP
FIX 14 HERL
FIX
FIX
FIX

FIX 18 HFMT

FIX 19 SPMT

1 HRIL
2 HRIH

5HBIL
6HBIH
7HLM1
8HLM2

9HLM3
10 HAD1
11 HAD2
12 HAKE

15 HLMC
16 HPWL
17 HPWC

Item name & ( Description )No. Name

H/W AKB R INI DATA L ( H/W AKB RED OUTPUT LOWER )
H/W AKB R INI DATA H ( H/W AKB RED OUTPUT UPPER )

H/W AKB G INI DATA L ( H/W AKB GREEN OUTPUT LOWER )

H/W AKB G INI DATA H ( H/W AKB GREEN OUTPUT UPPER )
H/W AKB B INI DATA L (H/W AKB BLUE OUTPUT LOWER)
H/W AKB B INI DATA H (H/W AKB BLUE OUTPUT UPPER)
AKB_LIM1<7:0> ( H/W AKB LIM1 )
AKB_LIM2<7:0> ( H/W AKB LIM2 )
AKA_LIM3<7:0> ( H/W AKB LIM3 )
AKB_ADD1<7:0> ( H/W AKB SPEED1 )
AKB_ADD2<7:0> ( H/W AKB SPEED2 )
AKB_EN ( H/W AKB MANUAL [ MCU ] / HARD
AKB_SPEED
AKB_SWERR<7:0>
AKB_ERRC<7:0> ( H/W AKB ERROR DET TIME )
AKBSWPON<7:0> ( H/W AKB POWER ON TRESH )
AKB_PWERRC ( H/W AKB POWER ON TIME )
H/W AKB2 HOLD TIMER ( H/W AKB2 HOLD TIMER (@
100 MSEC ) [ 0: No hold ]
AKB POW ON MUTE EXIT ( AKB POWER ON MUTE EXIT
TIMMER )

H/W AKB SPEED

H/W AKB ERROR DET THRESH

NTSC

Init

Data

soft cont'l
soft cont'l

soft cont'l

soft cont'l
soft cont'l
soft cont'l

6
12
21

2

6

1

3
40
20

4
90

20

120

KV-27FS120/29FA310/29FS120

29

KV-27FS120/29FA310/29FS120

Service

Group

SSOR

AUDIO

PROCE

Service

Group

Fix/
Var

VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR
VAR

Fix/
Var

No. Name

1 SBAL
2 SBAS
3STRE
4SRL
5 BBOL
6 BBOH
7 BBSL
8 BBSH

9 BBGL
10 BBGH
11 BBTL
12 BBTH
13 BBDL
14 BBDH
15 VFIX
16 AGCL
17 VCOF

No. Name Item name & ( Description )

SBAL ( SUB BALANCE )
SBAS ( SUB BASS )
STRE ( SUB TREBLE )
SRL ( SURROUND LEVEL )
BBOL ( SURROUND OFF-BBE LOW )
BBOH ( SURROUND OFF-BBE HIGH)
BBSL ( SIMULATE BBE LOW )
BBSH ( SIMULATE BBE HIGH )
BBGL ( WOW GAME BBE LOW )
BBGH ( WOW GAME BBE HIGH )
BBTL ( SRS BBE LOW )
BBTH ( SRS BBE HIGH )
BBDL ( Audio Processor Prologic BBE Low for DOLBY )
BBDH ( Audio Processor Prologic BBE High for DOLBY )
VFIX ( AUDIO OUTPUT FIX DATA )
AGCL ( AGC LEVEL )
RF OFFSET DATA

Item name & ( Description )

NTSC

29FA310 27FS120

44
00
60
00
86
45
24
44
60
40
06
04
60
40
0 243
22
99

NTSC

29FA310 27FS120

VAR

AP2

VAR
VAR
VAR
VAR
VAR
VAR

KV-27FS120/29FA310/29FS120

1 BBEL

2 BBEH

3 BBOL

4 BBSL

5 BBGL

6AGCL

7 DDOF

SUB AUDIO PROCESSOR PROLOGIC BBE LOW
SUB AUDIO PROCESSOR PROLOGIC BBE HIGH
SURROUND OFF-BBE LOW
SIMULATE BBE LOW
WOW GAME BBE LOW
SUB AUDIO PROCESSOR AGC LEVEL
DOLBY OFFSET DATA

90
90
90
50

10 0

20

15 0

30