Sony 26-473-01, 26-483-01 User Manual

Page 1
Configuration and ConnectionsSony LCD Compatible Installation
SYSTEM 4
xixi
xi
xixi
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: SONY LCD compatible
Included Communications Adapter(s):
Quantity Part Number Description
1 26-483-01 ADP, IR COMM 1 26-473-01 ADP, UNV, “E”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE” IN THE “CONFIG AS” COLUMN. IF Y OUR PROJECTOR MODEL DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE Y OUR SWITCHER
WITH THE CORRECT SETTINGS. PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR: SONY LCD VPL-X600 or
SONY VPL-X2000U
Config MODEL SW1 SW2 SW3 SW4 SW5 SW6 PROJ COMM
as 1 2 3 4 CABLE ADAPTER
Sony VPL-X600 off on off on 0 0 3 5 1 J15 26-483-01Sony VPL-X2000U off on off on 0 0 3 5 1 J15 26-483-01
Sony RS-232 off on off on 0 0 8 E 0 J15 26-473-01
Extron • System 4
xixi
xi
Switcher Series • User’s Manual • P/N 68-428-02 Rev. C
xixi
Page 2
Sony LCD Compatible Installation Configuration and Connections
y
)
Connecting System 4
[System 4xi model and software
version displayed here]
(See note.)
(See note.)
(See note.)
(Note: Information depends on
stem 4xi
S
(See note.)
setup.
}
xixi
xi to Sony VPL-X600
xixi
If the System 4xi is already configured for a Sony LCD VPL-X600 projector, go to step 4. If it is not set up correctly, it will be necessary to change switch
settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration.
1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Sony LCD projector. Apply power to the System 4xi and do the following:
a. Press to display the MENU SELECT on the LCD screen. b. Press or to step to Menu 8. c. Press to select this menu. d. Press or to display the configuration. The example to the left is general,
yours will show the System 4xi model name, the software version and the following information: PRJ = SONY PRJ BAUD = 9600 UNIT No. = 000 HST BAUD = 9600 (value depends upon setup Menu 3)
2. Go to the procedure on page 2-3 of the System 4xi cover. Then go to page 2-4 and refer to the configuration below to set up the Main Controller board. Continue with Step 3 (below) when the configuration is correct.
System 4xi User’s Manual
to remove the
Config
as
Model
Sony LCD VPL-X600
SW4
3. Double-check your work and be sure the System 4xi cover is on securely.
SW6
SW1
1 2 3 4
off on off on 0 0
SW2
SW2 SW3 SW4 SW5 SW6
351
SW3
SW1
4
PROJ
CABLE
SW5
J15
3
2
J15
1
Comm
Adapter
26-4
ON
83-01
Extron • System 4
4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.
__________ Changes in some switch configurations are not detected until the power is
removed at the AC cord, and then restored.
Refer to the following connection diagram and continue.
xixi
xi
Switcher Series • User’s Manual • P/N 68-428-02 Rev. C
xixi
Page 1
Page 3
Configuration and ConnectionsSony LCD Compatible Installation
5. Verify that the IR Comm Adapter is configured correctly (refer to the
Adapter User’s Guide
). Connect the 3.5 mm male plug end of the supplied cable into the “OUT” jack of the IR Comm Adapter. Connect the other end of the cable into the “CONTROL S IN” port of the projector. If a hardwired remote or host controller is being implemented, connect that device to the “IN” jack of the IR Comm Adapter.
6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4xi. Connect the other end of the cable into the IR Comm Adapter’s “PROJECTOR CONTROL” port.
______ Secure all of the connector screws.
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable into the System 4xi output Connect the 15-pin male end of the RGBS/HV cable into “INPUT A” of the projector.
Use the illustration below as a guide when connecting the System 4xi to a Sony LCD projector. Refer to Sony documentation to continue the installation.
Hardwired remote/
host controller
○○○○○○○○○○○○
IR Comm
○○○○○○○○○○○○○○
IR Comm Adapter
26-483-01
Cable
26-485-01
Female
9-pin
15-pin
CC 50'
15-pin
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the
Extron • System 4
System 4xi. See page 2-5 for cabling guidelines.
xixi
xi
Switcher Series • User’s Manual • P/N 68-428-02 Rev. C
xixi
Page 2
Page 4
Sony LCD Compatible Installation Configuration and Connections
y
)
Connecting System 4
[System 4xi model and software
version displayed here]
(See note.)
(See note.)
(See note.)
(Note: Information depends on
stem 4xi
S
(See note.)
setup.
xixi
xi to Sony VPL-X2000U
xixi
If the System 4xi is already configured for a Sony LCD VPL-X2000U projector,
go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration.
1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Sony LCD projector. Apply power to the System 4xi and do the following:
a. Press to display the MENU SELECT on the LCD screen. b. Press or to step to Menu 8. c. Press to select this menu. d. Press or to display the configuration. The example to the left is general,
yours will show the System 4xi model name, the software version and the following information: PRJ = SONY
}
PRJ BAUD = 9600 UNIT No. = 000 HST BAUD = 9600 (value depends upon setup Menu 3)
2. Go to the procedure on page 2-3 of the System 4xi cover. Then go to page 2-4 and refer to the configuration below to set up the Main Controller board. Continue with Step 3 (below) when the configuration is correct.
System 4xi User’s Manual
to remove the
Config
as
Model
Sony LCD VPL-X2000U
SW4
3. Double-check your work and be sure the System 4xi cover is on securely.
SW1
1 2 3 4
off on off on 0 0
SW2
SW6
SW2 SW3 SW4 SW5 SW6
351
SW3
PROJ
CABLE
J15
SW5
J15
SW1
4
3
2
Comm
Adapter
26-4
1
ON
83
-01
Extron • System 4
4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.
__________ Changes in some switch configurations are not detected until the power is
removed at the AC cord, and then restored.
Refer to the following connection diagram and continue.
xixi
xi
Switcher Series • User’s Manual • P/N 68-428-02 Rev. C
xixi
Page 3
Page 5
Configuration and ConnectionsSony LCD Compatible Installation
5. Verify that the IR Comm Adapter is configured correctly (refer to the
Adapter User’s Guide
). Connect the 3.5 mm male plug end of the supplied cable into the “OUT” jack of the IR Comm Adapter. Connect the other end of the cable into the “CONTROL S IN” port of the projector. If a hardwired remote or host controller is being implemented, connect that device to the “IN” jack of the IR Comm Adapter.
6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4xi. Connect the other end of the cable into the IR Comm Adapter’s “PROJECTOR CONTROL” port.
______ Secure all of the connector screws.
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable into the System 4xi output Connect the other end of the cable into the “INPUT A” BNC connectors of the projector.
Use the illustration below as a guide when connecting the System 4xi to a Sony X2000U projector. Refer to Sony documentation to continue the installation.
Hardwired remote/
host controller
○○○○○○○○
IR Comm
IR Comm Adapter
26-483-01
Cable
26-485-01
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Female
9-pin
CC 50'
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the
Extron • System 4
15-pin
System 4xi. See page 2-5 for cabling guidelines.
xixi
xi
Switcher Series • User’s Manual • P/N 68-428-02 Rev. C
xixi
Page 4
Page 6
Sony LCD Compatible Installation Configuration and Connections
y
)
Connecting System 4
[System 4xi model and software
version displayed here]
(See note.)
(See note.)
(See note.)
(Note: Information depends on
stem 4xi
S
(See note.)
setup.
xixi
xi to Sony Projector under RS-232 Control
xixi
If the System 4xi is already configured for a Sony RS-232 projector, go to step
4. If it is not set up correctly, it will be necessary to change switch settings on the
System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration.
1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Sony RS-232 projector. Apply power to the System 4xi and do the following:
a. Press to display the MENU SELECT on the LCD screen. b. Press or to step to Menu 8. c. Press to select this menu. d. Press or to display the configuration. The example to the left is general,
yours will show the System 4xi model name, the software version and the following information: PRJ = SONY PRJ BAUD = 38400
}
UNIT No. = 000 HST BAUD = 9600 (value depends upon setup Menu 3)
2. Go to the procedure on page 2-3 of the
System 4xi User’s Manual
to remove the System 4xi cover. Then go to page 2-4 and refer to the configuration below to set up the Main Controller board. Continue with Step 3 (below) when the configuration is correct.
Config
as
Model
Sony RS-232
SW1
1 2 3 4
off on off on
SW2
SW6
SW4
SW2 SW3 SW4 SW5 SW6
00
SW3
8E0
PROJ
CABLE
J15
SW5
J15
SW1
4
3
2
1
Comm
Adapter
26-473-01
ON
3. Double-check your work and be sure the System 4xi cover is on securely.
Extron • System 4
4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.
__________ Changes in some switch configurations are not detected until the power is
removed at the AC cord, and then restored.
Refer to the following connection diagram and continue.
xixi
xi
Switcher Series • User’s Manual • P/N 68-428-02 Rev. C
xixi
Page 5
Page 7
Configuration and ConnectionsSony LCD Compatible Installation
5. Connect the Comm Adapter to the “RS-232C/422A” port on the projector.
6. Connect the CC-50’ or (CC-100’) cable from the 9-pin male connector of the Comm Adapter to the 15-pin HD “PJ COMM” port on the rear panel of the System 4xi.
______ Secure all of the connector screws.
7. Ensure the projector’s RS-232C/RS-422A switch is in the RS-232C position.
8. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable into the System 4xi output Connect the other end of the cable into the “INPUT A” BNC connectors of the projector.
Use the illustration below as a guide when connecting the System 4xi to a Sony RS-232 projector. Refer to Sony documentation to continue the installation.
0 1
9-pin9-pin
Comm Adapter
26-473-01
Female
Male
E
Male
9-pin
CC 50'
15-pin15-pin
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the
System 4xi. See page 2-5 for cabling guidelines.
____________ Ensure the projector’s INDEX and PERIPHERAL dials are set to 01.
Extron • System 4
xixi
xi
Switcher Series • User’s Manual • P/N 68-428-02 Rev. C
xixi
Page 6
Loading...